This clearly had never gotten tested, probably because you need a fairly
minimal configuration in order to disable DEBUG_FS (several other
options select it).
The dummy inline functions that were used for the no-DEBUG_FS case were
missing the argument names in the declarations.
Fixes: 1dac891c1c ("drm/i915: Register debugfs interface last")
Reported-and-tested-by: Jörg Otte <jrg.otte@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bspec says:
"Restriction : SRD must not be enabled when the PSR Setup time from DPCD
00071h is greater than the time for vertical blank minus one line."
Let's check for that and disallow PSR if we exceed the limit.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge drm updates from Dave Airlie:
"This is the main drm pull request for 4.8.
I'm down with a cold at the moment so hopefully this isn't in too bad
a state, I finished pulling stuff last week mostly (nouveau fixes just
went in today), so only this message should be influenced by illness.
Apologies to anyone who's major feature I missed :-)
Core:
Lockless GEM BO freeing
Non-blocking atomic work
Documentation changes (rst/sphinx)
Prep for new fencing changes
Simple display helpers
Master/auth changes
Register/unregister rework
Loads of trivial patches/fixes.
New stuff:
ARM Mali display driver (not the 3D chip)
sii902x RGB->HDMI bridge
Panel:
Support for new panels
Improved backlight support
Bridge:
Convert ADV7511 to bridge driver
ADV7533 support
TC358767 (DSI/DPI to eDP) encoder chip support
i915:
BXT support enabled by default
GVT-g infrastructure
GuC command submission and fixes
BXT workarounds
SKL/BKL workarounds
Demidlayering device registration
Thundering herd fixes
Missing pci ids
Atomic updates
amdgpu/radeon:
ATPX improvements for better dGPU power control on PX systems
New power features for CZ/BR/ST
Pipelined BO moves and evictions in TTM
GPU scheduler improvements
GPU reset improvements
Overclocking on dGPUs with amdgpu
Polaris powermanagement enabled
nouveau:
GK20A/GM20B volt and clock improvements.
Initial support for GP100/GP104 GPUs, GP104 will not yet support
acceleration due to NVIDIA having not released firmware for them as of yet.
exynos:
Exynos5433 SoC with IOMMU support.
vc4:
Shader validation for branching
imx-drm:
Atomic mode setting conversion
Reworked DMFC FIFO allocation
External bridge support
analogix-dp:
RK3399 eDP support
Lots of fixes.
rockchip:
Lots of small fixes.
msm:
DT bindings cleanups
Shrinker and madvise support
ASoC HDMI codec support
tegra:
Host1x driver cleanups
SOR reworking for DP support
Runtime PM support
omapdrm:
PLL enhancements
Header refactoring
Gamma table support
arcgpu:
Simulator support
virtio-gpu:
Atomic modesetting fixes.
rcar-du:
Misc fixes.
mediatek:
MT8173 HDMI support
sti:
ASOC HDMI codec support
Minor fixes
fsl-dcu:
Suspend/resume support
Bridge support
amdkfd:
Minor fixes.
etnaviv:
Enable GPU clock gating
hisilicon:
Vblank and other fixes"
* tag 'drm-for-v4.8' of git://people.freedesktop.org/~airlied/linux: (1575 commits)
drm/nouveau/gr/nv3x: fix instobj write offsets in gr setup
drm/nouveau/acpi: fix lockup with PCIe runtime PM
drm/nouveau/acpi: check for function 0x1B before using it
drm/nouveau/acpi: return supported DSM functions
drm/nouveau/acpi: ensure matching ACPI handle and supported functions
drm/nouveau/fbcon: fix font width not divisible by 8
drm/amd/powerplay: remove enable_clock_power_gatings_tasks from initialize and resume events
drm/amd/powerplay: move clockgating to after ungating power in pp for uvd/vce
drm/amdgpu: add query device id and revision id into system info entry at CGS
drm/amdgpu: add new definition in bif header
drm/amd/powerplay: rename smum header guards
drm/amdgpu: enable UVD context buffer for older HW
drm/amdgpu: fix default UVD context size
drm/amdgpu: fix incorrect type of info_id
drm/amdgpu: make amdgpu_cgs_call_acpi_method as static
drm/amdgpu: comment out unused defaults_staturn_pro static const structure to fix the build
drm/amdgpu: enable UVD VM only on polaris
drm/amdgpu: increase timeout of IB test
drm/amdgpu: add destroy session when generate VCE destroy msg.
drm/amd: fix deadlock of job_list_lock V2
...
Pull vfs updates from Al Viro:
"Assorted cleanups and fixes.
Probably the most interesting part long-term is ->d_init() - that will
have a bunch of followups in (at least) ceph and lustre, but we'll
need to sort the barrier-related rules before it can get used for
really non-trivial stuff.
Another fun thing is the merge of ->d_iput() callers (dentry_iput()
and dentry_unlink_inode()) and a bunch of ->d_compare() ones (all
except the one in __d_lookup_lru())"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (26 commits)
fs/dcache.c: avoid soft-lockup in dput()
vfs: new d_init method
vfs: Update lookup_dcache() comment
bdev: get rid of ->bd_inodes
Remove last traces of ->sync_page
new helper: d_same_name()
dentry_cmp(): use lockless_dereference() instead of smp_read_barrier_depends()
vfs: clean up documentation
vfs: document ->d_real()
vfs: merge .d_select_inode() into .d_real()
unify dentry_iput() and dentry_unlink_inode()
binfmt_misc: ->s_root is not going anywhere
drop redundant ->owner initializations
ufs: get rid of redundant checks
orangefs: constify inode_operations
missed comment updates from ->direct_IO() prototype change
file_inode(f)->i_mapping is f->f_mapping
trim fsnotify hooks a bit
9p: new helper - v9fs_parent_fid()
debugfs: ->d_parent is never NULL or negative
...
Some of our "for_each_xyz()" macro constructs make gcc unhappy about
lack of braces around if-statements inside or outside the loop, because
the loop construct itself has a "if-then-else" statement inside of it.
The resulting warnings look something like this:
drivers/gpu/drm/i915/i915_debugfs.c: In function ‘i915_dump_lrc’:
drivers/gpu/drm/i915/i915_debugfs.c:2103:6: warning: suggest explicit braces to avoid ambiguous ‘else’ [-Wparentheses]
if (ctx != dev_priv->kernel_context)
^
even if the code itself is fine.
Since the warning is fairly easy to avoid by adding a braces around the
if-statement near the for_each_xyz() construct, do so, rather than
disabling the otherwise potentially useful warning.
(The if-then-else statements used in the "for_each_xyz()" constructs are
designed to be inherently safe even with no braces, but in this case
it's quite understandable that gcc isn't really able to tell that).
This finally leaves the standard "allmodconfig" build with just a
handful of remaining warnings, so new and valid warnings hopefully will
stand out.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bunch of fixes for the 4.8 merge pull, nothing out of the ordinary. All
suitably marked up with cc: stable where needed.
* tag 'drm-intel-next-fixes-2016-07-25' of git://anongit.freedesktop.org/drm-intel:
drm/i915/gen9: Add WaInPlaceDecompressionHang
drm/i915/guc: Revert "drm/i915/guc: enable GuC loading & submission by default"
drm/i915/bxt: Fix inadvertent CPU snooping due to incorrect MOCS config
drm/i915/gen9: Clean up MOCS table definitions
drm/i915: Set legacy properties when using legacy gamma set IOCTL. (v2)
drm/i915: Enable polling when we don't have hpd
drm/i915/vlv: Disable HPD in valleyview_crt_detect_hotplug()
drm/i915/vlv: Reset the ADPA in vlv_display_power_well_init()
drm/i915/vlv: Make intel_crt_reset() per-encoder
drm/i915: Unbreak interrupts on pre-gen6
drm/i915/breadcrumbs: Queue hangcheck before sleeping
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXlRXSAAoJEHm+PkMAQRiGG/gH/0Z8O4zWOsrwO+X1mRToRDBH
joFOjAmCVe83T1VpF5LYNB+9+owL/dEDt6+ZIswnhH7AfQPjs4RqwS4PcuMbCDVO
+mDm0PmfcKaYcQZrB2Z2OwIzRNnfCTVcsDPhIHwuIHk0m4z/xuGZonD8KoAj0+tO
3yJF6sbE1KubDVjOb+lmZZSP3cXA0pDXrNhkYhE4Tsr8fiihGjeXSNJ8t2zPLjxo
W3MPqo0rzDvQsOwoF4TWHHagVaFSJlhLBBgqu33fI7uO3jtfQD2G8wG68JCND1j3
qbMoBfTLFV/yQmSIJUt0Wv1axaCcwnjpweEB35A/GEeZ0mNB1rDdoBeI1eKEQkc=
=DGFC
-----END PGP SIGNATURE-----
Backmerge tag 'v4.7' into drm-next
Linux 4.7
As requested by Daniel Vetter as the conflicts were getting messy.
Add this workaround to prevent hang when in place compression
is used.
References: HSD#2135774
Cc: stable@vger.kernel.org
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit 4ba9c1f7c7)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 041824ee25.
We have latency issues that might impact the performance: #96606.
and hangs and loading issues on resume after S4: #96526.
This is also blocking a platform milestone so let's disable
this for now while we make sure we don't have any more loading
issue, or related basic hangs and it pass BAT for real in all
platofmrs.
In case BAT is wrong let's first fix BAT before re-enable it here.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96606
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96526
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Christophe Prigent <christophe.prigent@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1468884477-30086-1-git-send-email-rodrigo.vivi@intel.com
(cherry picked from commit fe993bc958)
[danvet: Drop cc: stable since this is for 4.8 only.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Setting a write-back cache policy in the MOCS entry definition also
implies snooping, which has a considerable overhead. This is
unexpected for a few reasons:
- From user-space's point of view since it didn't want a coherent
surface (it didn't set the buffer as such via the set caching IOCTL).
- There is a separate MOCS entry field for snooping (which we never
set).
- This MOCS table is about caching in (e)LLC and there is no (e)LLC on
BXT. There is a separate table for L3 cache control.
Considering the above the current behavior of snooping looks like an
unintentional side-effect of the WB setting. Changing it to be LLC-UC
gets rid of the snooping without any ill-effects. For a coherent
surface the application would use a separate MOCS entry at index 1 and
call the set caching IOCTL to setup the PTE entries for the
corresponding buffer to be snooped. In the future we could also add a
new MOCS entry for coherent surfaces.
This resulted in 70% improvement in synthetic texturing benchmarks.
Kudos to Valtteri Rantala, Eero Tamminen and Michael T Frederick and
Ville who helped to narrow the source of problem to the kernel and to
the snooping behaviour in particular.
With a follow-up change to adjust the 3rd entry value
igt/gem_mocs_settings is passing after this change.
v2:
- Rebase on v2 of patch 1/2.
v3:
- Set the entry as LLC uncached instead of PTE-passthrough. This way
we also keep snooping disabled, but we also make the cacheability/
coherency setting indepent of the PTE which is managed by the
kernel. (Chris)
CC: Rong R Yang <rong.r.yang@intel.com>
CC: Yakui Zhao <yakui.zhao@intel.com>
CC: Valtteri Rantala <valtteri.rantala@intel.com>
CC: Eero Tamminen <eero.t.tamminen@intel.com>
CC: Michael T Frederick <michael.t.frederick@intel.com>
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Rong R Yang <rong.r.yang@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467380406-11954-3-git-send-email-imre.deak@intel.com
(cherry picked from commit 6bee14ed1e)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use named struct initializers for clarity. Also fix the target cache
definition to reflect its role in GEN9 onwards. On GEN8 a TC value of 0
meant ELLC but on GEN9+ it means the TC and LRU controls are taken from
the PTE.
No functional change, igt/gem_mocs_settings still passing after this
change.
v2: (Chris)
- Add back the hexa literals for the entries.
Add note that igt/gem_mocs_settings still passes.
CC: Rong R Yang <rong.r.yang@intel.com>
CC: Yakui Zhao <yakui.zhao@intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467380406-11954-2-git-send-email-imre.deak@intel.com
(cherry picked from commit e419899b7c)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As promised here's the pile of kbl cherry-picks assembled by Mika&Rodrigo.
It's a bit much, but all well-contained to kbl code and been tested for a
while in drm-intel-next. Still separate in case too much, but in that case
I think we'd need to disable kbl by default again (which would be annoying
too) in 4.7.
* tag 'topic/kbl-4.7-fixes-2016-07-18' of git://anongit.freedesktop.org/drm-intel: (28 commits)
drm/i915/kbl: Introduce the first official DMC for Kabylake.
drm/i915: Introduce Kabypoint PCH for Kabylake H/DT.
drm/i915/gen9: implement WaConextSwitchWithConcurrentTLBInvalidate
drm/i915/gen9: Add WaFbcHighMemBwCorruptionAvoidance
drm/i195/fbc: Add WaFbcNukeOnHostModify
drm/i915/gen9: Add WaFbcWakeMemOn
drm/i915/gen9: Add WaFbcTurnOffFbcWatermark
drm/i915/kbl: Add WaClearSlmSpaceAtContextSwitch
drm/i915/gen9: Add WaEnableChickenDCPR
drm/i915/kbl: Add WaDisableSbeCacheDispatchPortSharing
drm/i915/kbl: Add WaDisableGafsUnitClkGating
drm/i915/kbl: Add WaForGAMHang
drm/i915: Add WaInsertDummyPushConstP for bxt and kbl
drm/i915/kbl: Add WaDisableDynamicCreditSharing
drm/i915/kbl: Add WaDisableGamClockGating
drm/i915/gen9: Enable must set chicken bits in config0 reg
drm/i915/kbl: Add WaDisableLSQCROPERFforOCL
drm/i915/kbl: Add WaDisableSDEUnitClockGating
drm/i915/kbl: Add WaDisableFenceDestinationToSLM for A0
drm/i915/kbl: Add WaEnableGapsTsvCreditFix
...
The i915 driver is now using atomic properties and atomic commit
to handle the legacy set gamma IOCTL. However, if the driver is
configured without atomic (nuclear_pageflip = false), it won't
update the legacy properties for degamma_lut, gamma_lut and ctm
leaving them out of sync with the atomic version of the properties.
Until the driver is full atomic, make sure we update the non-atomic
version of the properties.
v2: Update the comment with a FIXME. (Daniel)
v3: Update arguments of the gamma_set vfunc (Lionel)
v4: Fixed vfunc prototype (Lionel)
igt-testcase: kms_pipe_color / legacy-gamma-reset-pipeX
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: stable@vger.kernel.org #v4.7
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1468591142-2253-1-git-send-email-lionel.g.landwerlin@intel.com
(cherry picked from commit a87848750e)
Unfortunately, there's two situations where we lose hpd right now:
- Runtime suspend
- When we've shut off all of the power wells on Valleyview/Cherryview
While it would be nice if this didn't cause issues, this has the
ability to get us in some awkward states where a user won't be able to
get their display to turn on. For instance; if we boot a Valleyview
system without any monitors connected, it won't need any of it's power
wells and thus shut them off. Since this causes us to lose HPD, this
means that unless the user knows how to ssh into their machine and do a
manual reprobe for monitors, none of the monitors they connect after
booting will actually work.
Eventually we should come up with a better fix then having to enable
polling for this, since this makes rpm a lot less useful, but for now
the infrastructure in i915 just isn't there yet to get hpd in these
situations.
Changes since v1:
- Add comment explaining the addition of the if
(!mode_config->poll_running) in intel_hpd_init()
- Remove unneeded if (!dev->mode_config.poll_enabled) in
i915_hpd_poll_init_work()
- Call to drm_helper_hpd_irq_event() after we disable polling
- Add cancel_work_sync() call to intel_hpd_cancel_work()
Changes since v2:
- Apparently dev->mode_config.poll_running doesn't actually reflect
whether or not a poll is currently in progress, and is actually used
for dynamic module paramter enabling/disabling. So now we instead
keep track of our own poll_running variable in dev_priv->hotplug
- Clean i915_hpd_poll_init_work() a little bit
Changes since v3:
- Remove the now-redundant connector loop in intel_hpd_init(), just
rely on intel_hpd_poll_enable() for setting connector->polled
correctly on each connector
- Get rid of poll_running
- Don't assign enabled in i915_hpd_poll_init_work before we actually
lock dev->mode_config.mutex
- Wrap enabled assignment in i915_hpd_poll_init_work() in READ_ONCE()
for doc purposes
- Do the same for dev_priv->hotplug.poll_enabled with WRITE_ONCE in
intel_hpd_poll_enable()
- Add some comments about racing not mattering in intel_hpd_poll_enable
Changes since v4:
- Rename intel_hpd_poll_enable() to intel_hpd_poll_init()
- Drop the bool argument from intel_hpd_poll_init()
- Remove redundant calls to intel_hpd_poll_init()
- Rename poll_enable_work to poll_init_work
- Add some kerneldoc for intel_hpd_poll_init()
- Cross-reference intel_hpd_poll_init() in intel_hpd_init()
- Just copy the loop from intel_hpd_init() in intel_hpd_poll_init()
Changes since v5:
- Minor kerneldoc nitpicks
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 19625e85c6)
One of the things preventing us from using polling is the fact that
calling valleyview_crt_detect_hotplug() when there's a VGA cable
connected results in sending another hotplug. With polling enabled when
HPD is disabled, this results in a scenario like this:
- We enable power wells and reset the ADPA
- output_poll_exec does force probe on VGA, triggering a hpd
- HPD handler waits for poll to unlock dev->mode_config.mutex
- output_poll_exec shuts off the ADPA, unlocks dev->mode_config.mutex
- HPD handler runs, resets ADPA and brings us back to the start
This results in an endless irq storm getting sent from the ADPA
whenever a VGA connector gets detected in the middle of polling.
Somewhat based off of the "drm/i915: Disable CRT HPD around force
trigger" patch Ville Syrjälä sent a while back
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit b236d7c842)
While VGA hotplugging worked(ish) before, it looks like that was mainly
because we'd unintentionally enable it in
valleyview_crt_detect_hotplug() when we did a force trigger. This
doesn't work reliably enough because whenever the display powerwell on
vlv gets disabled, the values set in VLV_ADPA get cleared and
consequently VGA hotplugging gets disabled. This causes bugs such as one
we found on an Intel NUC, where doing the following sequence of
hotplugs:
- Disconnect all monitors
- Connect VGA
- Disconnect VGA
- Connect HDMI
Would result in VGA hotplugging becoming disabled, due to the powerwells
getting toggled in the process of connecting HDMI.
Changes since v3:
- Expose intel_crt_reset() through intel_drv.h and call that in
vlv_display_power_well_init() instead of
encoder->base.funcs->reset(&encoder->base);
Changes since v2:
- Use intel_encoder structs instead of drm_encoder structs
Changes since v1:
- Instead of handling the register writes ourself, we just reuse
intel_crt_detect()
- Instead of resetting the ADPA during display IRQ installation, we now
reset them in vlv_display_power_well_init()
Cc: stable@vger.kernel.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Rebase over dev_priv/drm_device embedding.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 9504a89247)
This lets call intel_crt_reset() in contexts where IRQs are disabled and
as such, can't hold the locks required to work with the connectors.
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 28cf71ce3e)
Version 1.01.
This firmware is made for Kabylake platform so it doesn't
need the stepping workaround that we had before.
v2: Rebased on top of latest nightly with min version
required change.
v3: With right CSR_VERSION (Patrik).
Cc: Christophe Prigent <christophe.prigent@intel.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Reviewed-by: Ben Widawsky <benjamin.widawsky@intel.com> (v1)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461707991-15336-1-git-send-email-rodrigo.vivi@intel.com
(cherry picked from commit 4922d49195)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The i915 driver checks for color management properties changes as part
of a plane update. Therefore a color management update must imply a
plane update, otherwise we never update the transformation matrixes
and degamma/gamma LUTs.
v2: add comment about moving the commit of color management registers
to an async worker
v3: Commit color management register right after vblank
v4: Move back color management commit condition together with planes
commit
v5: Trigger color management commit through the planes commit (Daniel)
v6: Make plane change update more readable
Fixes: 20a34e78f0 (drm/i915: Update color management during vblank evasion.)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
References: https://lkml.org/lkml/2016/7/14/614
Reviewed-and-tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464183041-8478-1-git-send-email-lionel.g.landwerlin@intel.com
(cherry picked from commit e7852a4b3a)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
eDP should be treated as connected even if doesn't have an EDID. In that
case we'll use the timings from the VBT. That used to be the case until
commit f21a21983e ("drm/i915: Splitting intel_dp_detect")
broke things by considering even eDP disconnected if we fail to get
an EDID for it.
Fix things up again by treating eDP as always connected.
Cc: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Cc: Nathan D Ciobanu <nathan.d.ciobanu@intel.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: Larry Finger <larry.finger@lwfinger.net>
Reported-by: Larry Finger <larry.finger@lwfinger.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96675
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: f21a21983e ("drm/i915: Splitting intel_dp_detect")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Larry Finger <larry.finger@lwfinger.net>
Link: http://patchwork.freedesktop.org/patch/msgid/1468836914-16537-1-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit 1b7f2c8b07)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some Kabylake SKUs are going to use Kabypoint PCH.
It is mainly for Halo and DT ones.
>From our specs it doesn't seem that KBP brings
any change on the display south engine. So let's consider
this as a continuation of SunrisePoint, i.e., SPT+.
Since it is easy to get confused by a letter change:
KBL = Kabylake - CPU/GPU codename.
KBP = Kabypoint - PCH codename.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96826
Link: http://patchwork.freedesktop.org/patch/msgid/1467418032-15167-1-git-send-email-rodrigo.vivi@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit 22dea0be50)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
This patch enables a workaround for a mid thread preemption
issue where a hardware timing problem can prevent the
context restore from happening, leading to a hang.
v2: move to gen9_init_workarounds (Arun)
v3: move to start of gen9_init_workarounds (Arun)
Signed-off-by: Tim Gore <tim.gore@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465816501-25557-1-git-send-email-tim.gore@intel.com
(cherry picked from commit a8ab5ed5e1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Bspec states that we need to set nuke on modify all to prevent
screen corruption with fbc on skl and kbl.
v2: proper workaround name
References: HSD#2227109, HSDES#1404569388
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-27-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 031cd8c85a)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Set bit 8 in 0x43224 to prevent screen corruption and system
hangs on high memory bandwidth conditions. The same wa also suggest
setting bit 31 on ARB_CTL. According to another workaround we gain
better idle power savings when FBC is enabled.
v2: use correct workaround name
v3: split out overlapping wa for corruption avoidance (Ville)
References: HSD#2137218, HSD#2227171, HSD#2136579, BSID#883
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-26-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 303d4ea522)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
According to bspec this prevents screen corruption when fbc is
used.
v2: This workaround has a name, use it (Ville)
v3: remove bogus gen check on ilk/vlv wm path (Ville)
References: HSD#2135555, HSD#2137270, BSID#562
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-25-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 0f78dee6f0)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Workaround for display underrun issues with Y & Yf Tiling.
Set this on all gen9 as stated by bspec.
v2: proper workaround name
References: HSD#2136383, BSID#857
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-22-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 590e8ff04b)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
We need to disable clock gating in this unit to work around
hardware issue causing possible corruption/hang.
v2: name the bit (Ville)
v3: leave the fix enabled for 2227050 and set correct bit (Matthew)
v4: Split out the skl part in separate commit for easier backport
References: HSD#2227156, HSD#2227050
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-20-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 4de5d7ccbc)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Bspec states that we need to turn off dynamic credit
sharing on kbl revid a0 and b0. This happens by writing bit 28
on 0x4ab8.
References: HSD#2225601, HSD#2226938, HSD#2225763
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-15-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit c0b730d572)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Extend the scope of this workaround, already used in skl,
to also take effect in kbl.
v2: Fix KBL_REVID_E0 (Matthew)
References: HSD#2132677
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-12-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit fe90581987)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Add this workaround for kbl revid A0 only.
v2: rebase
v3: carve out a non related workaround (Chris)
References: HSD#1911714
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-9-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 8401d42fd5)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
We need this crucial workaround from skl also to all kbl revisions.
Lack of it was causing system hangs on skl enabling so this is
a must have.
v2: Don't add revid checks to gen9 init workarounds (Arun)
References: HSD#2126660
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-8-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit e587f6cb0a)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Past evidence with system hangs and hsds tie
WaForceEnableNonCoherent and WaDisableHDCInvalidation to
WaForceContextSaveRestoreNonCoherent. Documentation
states that WaForceContextSaveRestoreNonCoherent would
not be needed on skl past E0 but evidence proved otherwise. See
commit <510650e8b2ab> ("drm/i915/skl: Fix spurious gpu hang with gt3/gt4
revs"). In this scope consider kbl to be skl with a bigger revision than
E0 so play it safe and bind these two workarounds to the
WaForceContextSaveRestoreNonCoherent, and apply to all gen9.
v2: fix comment (Matthew)
References: HSD#2134449, HSD#2131413
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-7-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit bbaefe72a0)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
We need this for kbl a0 boards. Note that this should be also
for bxt A0 but we omit that on purpose as bxt A0's are
out of fashion already.
References: HSD#1912158, HSD#4393097
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-5-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 6e4f10c33a)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
We need to disable clock gating in this unit to work around
hardware issue causing possible corruption/hang.
v2: name the bit (Ville)
v3: leave the fix enabled for 2227050 and set correct bit (Matthew)
References: HSD#2227156, HSD#2227050
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-2-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit eee8efb02a)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Kernel only need to add a register to HW whitelist, required for a
preemption related issue.
Reference: HSD#2131039
Reviewed-by: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465203169-16591-1-git-send-email-arun.siluvery@linux.intel.com
(cherry picked from commit 6bb6285582)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Found this while browsing Bspec. Looks like it applies to both skl and
kbl.
v2: Also for bxt (Art).
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Cc: "Runyan, Arthur J" <arthur.j.runyan@intel.com>
Reviewed-by: Sonika Jindal<sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463642060-30728-1-git-send-email-daniel.vetter@ffwll.ch
(cherry picked from commit dc00b6a07c)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Dell XPS 13 9350 apparently doesn't like it when we use the panel type
from OpRegion. The OpRegion panel type (0) tells us to use use low
vswing for eDP, whereas the VBT panel type (2) tells us to use normal
vswing. The problem is that low vswing results in some display flickers.
Since no one seems to know how this stuff is supposed to be handled,
let's just ignore the OpRegion panel type on SKL for now.
v2: Print the panel type correctly in the debug output
Reported-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: drm-intel-fixes@lists.freedesktop.org
References: https://lists.freedesktop.org/archives/intel-gfx/2016-June/098826.html
Fixes: a05628195a ("drm/i915: Get panel_type from OpRegion panel details")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1468324837-29237-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit bb10d4ec3b)
[danvet: Fix up cherry-pick conflict with an s/dev_priv/dev/.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prior to gen6 we didn't have per-ring IMR registers, which means that
since commit 61ff75ac20 ("drm/i915: Simplify enabling
user-interrupts with L3-remapping") we're now masking off all interrupts
when init_render_ring() gets called. That's rather rude. Let's limit
the ring IMR frobbing to machines that actually have the per-ring IMR
registers.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 61ff75ac20 ("drm/i915: Simplify enabling user-interrupts with L3-remapping")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1468340687-3596-1-git-send-email-ville.syrjala@linux.intel.com
Reviewd-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 035ea405c9)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Never go to sleep waiting on the GPU without first ensuring that we will
get woken up.
We have a choice of queuing the hangcheck before every schedule() or the
first time we wakeup. In order to simply accommodate both the signaler
and the ordinary waiter, move the queuing to the common point of
enabling the irq. We lose the paranoid safety of ensuring that the
hangcheck is active before the sleep, but avoid code duplication (and
redundant hangcheck queuing).
Testcase: igt/prime_busy
Fixes: c81d46138d ("drm/i915: Convert trace-irq to the breadcrumb waiter")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1468055535-19740-2-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
(cherry picked from commit 232af392fd)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
