Some variants of the dw-hdmi on Rockchip socs use a separate phy block
accessed via the generic phy framework, so allow them to be included
if such a phy reference is found.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Zheng Yang <zhengyang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180912124740.20343-5-heiko@sntech.de
Some newer Rockchip SoCs use an Innosilicon hdmiphy accessed via general
mmio, so allow these to be referenced via the regular phy interfaces
and therefore add optional phy-related properties to the binding.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180912124740.20343-4-heiko@sntech.de
So far we always encountered socs with 2 output crtcs needing the driver
to tell the hdmi block which output to connect to. But there also exist
socs with only one crtc like the rk3228, rk3328 and rk3368.
So adapt the register field to simply carry a negative value to signal
that no output-switching is necessary.
changes in v3:
- fixed wording issue found by Robin Murphy
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Zheng Yang <zhengyang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180912124740.20343-3-heiko@sntech.de
In some IP implementations the reading of the phy-type may be broken.
One example are the Rockchip rk3228 and rk3328 socs that use a separate
vendor-type phy from Innosilicon but still report the HDMI20_TX type.
So allow the glue driver to force the vendor-phy for these cases.
In the future it may be necessary to allow forcing other types, but
for now we'll keep it simply to the case actually seen in the wild.
changes in v3:
- only allow forcing vendor type, as suggested by Laurent
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Zheng Yang <zhengyang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180912124740.20343-2-heiko@sntech.de
Link: https://patchwork.freedesktop.org/patch/msgid/20180912124740.20343-3-heiko@sntech.de
Hardware allow to read the position in scanout buffer so
we can use this information to make wait of vblank more accurate.
Active area bounds (start, end, total height) have already been
computed and written in ltdc registers, read them and get the
current line position to compute vpos value.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Yannick Fertré <yannick.fertre@st.com>
Tested-by: Yannick Fertré <yannick.fertre@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180629130140.16004-1-benjamin.gaignard@linaro.org
This patch adds Olimex Ltd. LCD-OLinuXino bridge panel driver. The panel
is used with different LCDs (currently from 480x272 to 1280x800). A
small EEPROM chip is used for identification, which holds some factory
data and timing requirements.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1531383729-13932-1-git-send-email-stefan@olimex.com
This panel is marketed as Banana Pi 7" LCD display. On the back is
a sticker denoting the model name S070WV20-CT16.
This is a 7" 800x480 panel connected through a 24-bit RGB interface.
However the panel only does 262k colors.
Depending on the variant, the PCB attached to the panel module either
supports DSI, or DSI + 24-bit RGB. DSI is converted to 24-bit RGB via
an onboard ICN6211 MIPI DSI - RGB bridge chip, then fed to the panel
itself.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180907041948.19913-5-wens@csie.org
There is no need to check innolux->base.dev when trying to remove
the panel, as that variable is always set directly before the panel
gets added and will still be available on panel_remove.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180816140920.5009-1-heiko@sntech.de
GPD has done it again, make a nice device (good), use way too generic
DMI strings (bad) and use a portrait screen rotated 90 degrees (ugly).
Because of the too generic DMI strings this entry is also doing bios-date
matching, so the gpd_win2 data struct may very well need to be updated
with some extra bios-dates in the future.
Reported-and-tested-by: russianneuromancer@ya.ru
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180909133457.10636-3-hdegoede@redhat.com
The variable is declared in an #ifdef section, but the user is
now unconditional, which leads to a build failure:
drivers/gpu/drm/imx/imx-drm-core.c: In function 'imx_drm_bind':
drivers/gpu/drm/imx/imx-drm-core.c:264:6: error: 'legacyfb_depth' undeclared (first use in this function); did you mean 'lockdep_depth'?
Remove the remaining #ifdef as well.
Fixes: f53705fd98 ("drm/imx: Use drm_fbdev_generic_setup()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180926193846.2490574-1-arnd@arndb.de
The hs_start interrupt on rk3188 fires at the start of a new frame, so
serves essentially the same purpose as the dsp_hold_valid irq in checking
when the last frame got delivered when going to standby. So define it
to fix a hang on atomic_disable of the vop because the completion never
really completed before.
Fixes: 428e15cc41 ("drm/rockchip: vop: add rk3188 vop definitions")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Sandy Huang <hjc@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180923123730.14706-1-heiko@sntech.de
This patch unifies the naming of DRM functions for reference counting
of struct drm_device. The resulting code is more aligned with the rest
of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <contact@tzimmermann.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180701132415.10161-1-contact@tzimmermann.org
R40 DE2 mixers are similar to those found in A83T, except it needs
different clock settings.
Add a compatibles for them.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-14-jernej.skrabec@siol.net
This reverts commit 3510e7a7f9.
During the 4.19 merge window for drm-misc, two patches critical to
supporting the display pipeline on the Allwinner R40 SoC were missed.
They were applied later but missed the merge window deadline. As a
result 4.19-rc1 kernel would crash on the R40 when it couldn't parse
the new device tree structure. We ended up removing support for the
R40 display pipeline for 4.19.
Since the missing patches are already merged for 4.20, we can now
revert the commit that removed support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180921142743.8711-1-wens@csie.org
This patch unifies the naming of DRM functions for reference counting
of struct drm_device. The resulting code is more aligned with the rest
of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180926114312.23097-1-tzimmermann@suse.de
The lcdif block is only powered on when display is active so plane
updates when not enabled are not valid. Writing to an unpowered IP block
is mostly ignored but can trigger bus errors on some chips.
Prevent this situation by switching to drm_atomic_helper_commit_tail_rpm
and having the drm core ensure atomic_plane_update is only called while
the crtc is active. This avoids having to keep track of "enabled" bits
inside the mxsfb driver.
This also requires handling the vblank event for disable from
mxsfb_pipe_disable.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Suggested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/c19c0c00ed42e8e8f7965aa4821ac295abc5cd05.1537191359.git.leonard.crestez@nxp.com
Adding lcdif nodes to a power domain currently results in
black/corrupted screens or hangs because power is not correctly enabled
when required.
Ensure power is on when display is active by adding
pm_runtime_get/put_sync to mxsfb_pipe_enable/disable.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/ee88148399c63494cda4129b05444b0ac331b7a7.1537191359.git.leonard.crestez@nxp.com
LCDIF will repeatedly display data from CUR_BUF and set CUR_BUF to
NEXT_BUF when done. Since we are only ever writing to NEXT_BUF the
display will show an initial corrupt frame.
Fix by writing the FB paddr to both CUR_BUF and NEXT_BUF when
activating the CRTC.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/7cdac9c064cc2b8a3d237934f186da98cefe6cb3.1537191359.git.leonard.crestez@nxp.com
The main axi clk is disabled at the end of mxsfb_crtc_mode_set_nofb and
immediately reenabled in mxsfb_enable_controller.
Avoid this by moving the handling of axi clk one level up to
mxsfb_crtc_enable. Do the same for mxsfb_crtc_disable for symmetry.
This shouldn't have any functional effect.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/985c1f1cad250bd9ca154b3e4b3f913c310eeabd.1537191359.git.leonard.crestez@nxp.com
This patch unifies the naming of DRM functions for reference counting
of struct drm_device. The resulting code is more aligned with the rest
of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180926115640.24755-1-tzimmermann@suse.de
This patch unifies the naming of DRM functions for reference counting
of struct drm_device. The resulting code is more aligned with the rest
of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180926120212.25359-1-tzimmermann@suse.de
Another "small driver" moving into drm-misc. Stefan has also offered to
co-maintain it.
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180919204026.3217-2-sean@poorly.run
Implement vmap/vunmap so we can export dmabufs to
other drivers, such as video4linux.
Tested with a virtio-gpu / vivid (virtual capture driver)
pipeline, where the vivid driver imports the dmabufs exported
by virtio-gpu.
Note that dma_buf_vmap() does its own vmap counting, so
it's not needed to take care of it in the driver.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20180925161606.17980-4-ezequiel@collabora.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Currently, virtio_gpu_object_kmap() is only called by
virtio_gpufb_create(), when a DRM framebuffer is created.
Thus, instead of returning the vmap'ed address, emit a warning
if virtio_gpu_object_kmap is called on an already mapped
object. With this change, kmap/kunmap calls are now balanced.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20180925161606.17980-3-ezequiel@collabora.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The function ttm_bo_put releases a reference to a TTM buffer object. The
function's name is more aligned to the Linux kernel convention of naming
ref-counting function _get and _put.
A call to ttm_bo_unref takes the address of the TTM BO object's pointer and
clears the pointer's value to NULL. This is not necessary in most cases and
sometimes even worked around by the calling code. A call to ttm_bo_put only
releases the reference without clearing the pointer.
The current behaviour of cleaning the pointer is kept in the calling code,
but should be removed if not required in a later patch.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Xinliang Liu <z.liuxinliang@hisilicon.com>
Signed-off-by: Xinliang Liu <z.liuxinliang@hisilicon.com>
This patch unifies the naming of DRM functions for reference counting
of struct drm_device. The resulting code is more aligned with the rest
of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Xinliang Liu <z.liuxinliang@hisilicon.com>
Signed-off-by: Xinliang Liu <z.liuxinliang@hisilicon.com>
convert drm_atomic_helper_suspend/resume() to use
drm_mode_config_helper_suspend/resume().
Fixed one sparse warning by making hibmc_drm_interrupt
static.
Signed-off-by: Ajit Negi <ajitn.linux@gmail.com>
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Xinliang Liu <z.liuxinliang@hisilicon.com>
Signed-off-by: Xinliang Liu <z.liuxinliang@hisilicon.com>
Switch to use Huawei PCI vendor ID macro from pci_ids.h file.
In addition, switch to use PCI_VDEVICE() instead of open coding.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xinliang Liu <z.liuxinliang@hisilicon.com>
Signed-off-by: Xinliang Liu <z.liuxinliang@hisilicon.com>
Currently the driver overwrites the surface depth provided by the fb
helper to give an invalid bpp/surface depth combination.
This has been exposed by commit 70109354fe ("drm: Reject unknown legacy
bpp and depth for drm_mode_addfb ioctl"), which now causes the driver to
fail to probe.
Fix by not overwriting the surface depth.
Fixes: d1667b8679 ("drm/hisilicon/hibmc: Add support for frame buffer")
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xinliang Liu <z.liuxinliang@hisilicon.com>
Signed-off-by: Xinliang Liu <z.liuxinliang@hisilicon.com>
Use DRM_FORMAT_HOST_XRGB8888, so we are using the correct format code
on bigendian machines. Also set the quirk_addfb_prefer_host_byte_order
mode_config bit so drm_mode_addfb() asks for the correct format code.
Both DRM_FORMAT_* and VIRTIO_GPU_FORMAT_* are defined to be little
endian, so using a different mapping on bigendian machines is wrong.
It's there because of broken drm_mode_addfb() behavior. So with
drm_mode_addfb() being fixed we can fix this too.
While wading through the code I've noticed we have a little issue in
virtio: We attach a format to the bo when it is created
(DRM_IOCTL_MODE_CREATE_DUMB), not when we map it as framebuffer
(DRM_IOCTL_MODE_ADDFB). Easy way out: Support a single format only.
Pick DRM_FORMAT_HOST_XRGB8888, it is the only one actually used in
practice. Drop unused mappings in virtio_gpu_translate_format().
With this patch applied both ADDFB and ADDFB2 ioctls work correctly in
the virtio-gpu.ko driver on big endian machines. Without the patch only
ADDFB (which still seems to be used by the majority of userspace) works
correctly.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20180921134704.12826-6-kraxel@redhat.com
Add bochs_hw_set_*_endian() helper functions, to set the framebuffer
byteorder at mode set time. Support both DRM_FORMAT_XRGB8888 and
DRM_FORMAT_BGRX8888 framebuffer formats, no matter what the native
machine byte order is.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20180921134704.12826-5-kraxel@redhat.com
Use DRM_FORMAT_HOST_XRGB8888, so we are using the correct format code
on bigendian machines. Also set the quirk_addfb_prefer_host_byte_order
mode_config bit so drm_mode_addfb() asks for the correct format code.
Create our own plane and use drm_crtc_init_with_planes() instead of
depending on the default created by drm_crtc_init(). That way the plane
format list is correct on bigendian machines.
Also re-add the framebuffer format check dropped by "df2052cc92 bochs:
convert to drm_fb_helper_fbdev_setup/teardown".
With this patch applied both ADDFB and ADDFB2 ioctls work correctly in
the bochs-drm.ko driver on big endian machines. Without the patch only
ADDFB (which still seems to be used by the majority of userspace) works
correctly.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20180921134704.12826-4-kraxel@redhat.com