The port net device passed to b53_fdb_copy is not used. Remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_serdes_power returns an error, so no need to print an error
message inside of it. Rather print it in its caller when the error is
ignored, which is in the mv88e6xxx_port_disable void function.
Catch and return its error in the counterpart mv88e6xxx_port_enable.
Fixes: 04aca99382 ("dsa: mv88e6xxx: Enable/Disable SERDES on port enable/disable")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the port enable/disable callbacks, which enable/disable the
SERDES interfaces, if applicable. This should save a bit of
power/heat.
We also need to enable SERDES on CPU and DSA ports, so keep the
existing call to the op, but make it conditional.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390X family has 8 SERDES lanes. These can be used for 2
10Gbps ports, ports 9 or 10. If these ports are used at slower speeds,
the SERDES lanes become available for other ports for 1000Base-X.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we use an op for SERDES operations, we don't need a flag for
it. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 family has a different SERDES implementation. Refactor
the mv88e6352 code into an ops function, so we can later add the
mv88e6390 code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The upcoming SERDES support will need to make use of PHY functions. Move
them out into a file of there own. No code changes.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cygnus is a small family of SoCs, of which we currently have
devicetree for BCM11360 and BCM58300. The 11360's B53 is mostly the
same as 58xx, just requiring a tiny bit of setup that was previously
missing.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the DSA public header includes switchdev.h, use the provided
switchdev_obj_dump_cb_t typedef for the object dump callback.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA drivers and core use switchdev. Include switchdev.h only once, in
the dsa.h public header, so that inclusion in DSA drivers or forward
declarations of switchdev structures in not necessary anymore.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With more drivers being added, it is time to sort the drivers to
impose some order.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A dsa_switch_tree instance holds a dsa_switch pointer and a port index
to identify the switch port to which the CPU is attached.
Now that the DSA layer has a dsa_port structure to hold this data, use
it to point the switch CPU port.
This patch simply substitutes s/dst->cpu_switch/dst->cpu_dp->ds/ and
s/dst->cpu_port/dst->cpu_dp->index/.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add default case to switch in order to avoid any chance of using an
uninitialized variable _low_, in case s->type does not match any of
the listed case values.
Addresses-Coverity-ID: 1398130
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If 'devm_kzalloc' fails, a NULL pointer will be dereferenced.
Return -ENOMEM instead, as done for some other memory allocation just a
few lines above.
Fixes: 98cd1552ea ("net: dsa: Mock-up driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 family of chips use only 2 of the 3 VTU Data registers to pack
the MemberTag and PortState VLAN data. This means that they must be
written or read before or after each VTU/STU operations.
Implement this variant to add support for VTU with such chips. These
chips have a 13th bit for the VID thus set their max_vid to 8191.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer chips such as the 88E6390 have a VTU Page bit in the VTU VID
register to specify a 13th bit for the VID. This can be used to support
8K VLANs.
When dumping the whole VTU, all VID bits must be set to one, including
this VTU Page bit. Add support for VID greater than 4095.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code which fetches or initializes a new VTU entry more concise.
This allows us the get rid of the old underscore prefix naming.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have chip operations for VTU accesses, mark all helpers from
global1_vtu.c as static. Only the various implementations of the
GetNext, LoadPurge and Flush operations need to be exposed.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new vtu_loadpurge operation to the chip info structure to differ
the various implementations of the VTU accesses.
Now that the STU handling is abstracted behind VTU operations, kill the
obsolete MV88E6XXX_FLAG_STU flag.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new vtu_getnext operation to the chip info structure to differ the
various implementations of the VTU accesses.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the code writes both VTU and STU data when loading a VTU entry,
load the corresponding STU entry at the same time.
This allows us to get rid of the STU management in the
_mv88e6xxx_vtu_new helper and thus remove the separate implementations
of STU Load/Purge and STU GetNext, as well as the unused family checks.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the code reads both VTU and STU data on VTU GetNext operation,
fetch the STU entry data of a VTU entry at the same time.
The STU data bits are masked with the VTU data bits and they are now all
read at the same time a VTU GetNext operation is issued.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the generic portion of code to issue an STU GetNext operation,
which will be used in other implementations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to access the VTU Data registers currently only supports the
88E6185 family and alike: 2-bit membership adjacent to 2-bit port state.
Even though the 88E6352 family introduced an indirect table to program
the VLAN Spanning Tree states, the usage of the VTU Data registers
remains the same regardless the VTU or STU operation.
Now that the mv88e6xxx_vtu_entry structure contains both port membership
and states data, factorize the code to access them in global1_vtu.c.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though every switch model has a different way to access the VTU
Data bits, the base implementation of the VTU GetNext operation remains
the same: wait, write the first VID to iterate from, start the
operation, and read the next VID.
Move this generic implementation into global1_vtu.c and abstract the
handling of the start VID (similarly to the ATU GetNext implementation),
before introducing a new chip operation for specific chips.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to access the VTU VID register in the global1_vtu.c file.
At the same time, move mv88e6xxx_g1_vtu_vid_write at the beginning of
_mv88e6xxx_vtu_loadpurge, which adds no functional changes but makes
future patches simpler.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to access the VTU SID register in the global1_vtu.c file.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to access the VTU FID register in the global1_vtu.c file.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the VTU flush operation to global1_vtu.c and call it from a
mv88e6xxx_vtu_setup helper, similarly to the ATU and PVT setup.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the helper functions to access the Global 1 VTU Operation register
to a new global1_vtu.c file, and get rid of the old underscore prefix
naming convention. This file will be extended will all VTU/STU related
code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN aware Marvell chips can program 802.1Q VLAN membership as well as
802.1s per VLAN Spanning Tree state using the same 3 VTU Data registers.
Some chips such as 88E6185 use different Data registers offsets for
ports state and membership, and program them in a single operation.
Other chips such as 88E6352 use the same register layout but program
them in distinct operations (an indirect table is used for 802.1s.)
Newer chips such as 88E6390 use the same offsets for both state and
membership in distinct operations, thus require multiple data accesses.
To correctly abstract this, split the "data" structure member of
mv88e6xxx_vtu_entry in two "state" and "member" members, before adding
VTU support for newer chips.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some chips don't have a VLAN Table Unit, most of them do have a 4K
table, some others as the 88E6390 family has a 13th bit for the VID.
Add a new max_vid member to the info structure, used to check the
presence of a VTU as well as the value used to iterate from in VTU
GetNext operations.
This makes the MV88E6XXX_FLAG_VTU obsolete, thus remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 58xx devices (Northstar Plus) do actually have their CPU port wired
at port 8, it was unfortunately set to port 5 (B53_CPU_PORT_25) which is
incorrect, since that is the second possible management port.
Fixes: 991a36bb46 ("net: dsa: b53: Add support for BCM585xx/586xx/88312 integrated switch")
Reported-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the correct software reset sequence for 58xx devices by
setting all 3 reset bits and polling for the SW_RST bit to clear itself
without a given timeout. We cannot use is58xx() here because that would
also include the 7445/7278 Starfighter 2 which have their own driver
doing the reset earlier on due to the HW specific integration.
Fixes: 991a36bb46 ("net: dsa: b53: Add support for BCM585xx/586xx/88312 integrated switch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Broadcom tags are not enabled in b53 (DSA_PROTO_TAG_NONE), we need
to make sure that the IMP/CPU port is included in the forwarding
decision.
Without this change, switching between non-management ports would work,
but not between management ports and non-management ports thus breaking
the default state in which DSA switch are brought up.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Reported-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_I2C=m and NET_DSA_SMSC_LAN9303=y, we run into a link error:
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_byte_reg_read':
regmap-i2c.c:(.text.regmap_smbus_byte_reg_read+0x18): undefined reference to `i2c_smbus_read_byte_data'
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_byte_reg_write':
regmap-i2c.c:(.text.regmap_smbus_byte_reg_write+0x18): undefined reference to `i2c_smbus_write_byte_data'
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_word_reg_read':
regmap-i2c.c:(.text.regmap_smbus_word_reg_read+0x18): undefined reference to `i2c_smbus_read_word_data'
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_word_read_swapped':
regmap-i2c.c:(.text.regmap_smbus_word_read_swapped+0x18): undefined reference to `i2c_smbus_read_word_data'
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_word_write_swapped':
This adds a Kconfig dependency to avoid the broken configuration.
Fixes: be4e119f99 ("net: dsa: LAN9303: add I2C managed mode support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the LAN9303 device is in MDIO manged mode, all register accesses must
be done via MDIO.
Please note: this code is compile time tested only due to the absence of such
configured hardware. It is based on a patch from Stefan Roese from 2014.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
CC: devicetree@vger.kernel.org
CC: robh+dt@kernel.org
CC: mark.rutland@arm.com
CC: sr@denx.de
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this mode the switch device and the internal phys will be managed via
I2C interface. The MDIO interface is still supported, but for the
(emulated) CPU port only.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
CC: devicetree@vger.kernel.org
CC: robh+dt@kernel.org
CC: mark.rutland@arm.com
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMSC/Microchip LAN9303 is an ethernet switch device with one CPU port
and two external ethernet ports with built-in phys.
This driver uses the DSA framework, but is currently only capable of
separating the two external ports. There is no offload support yet.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes build errors seen with CONFIG_GPIOLIB disabled and warnings enabled:
drivers/net/dsa/mt7530.c: In function 'mt7530_setup':
drivers/net/dsa/mt7530.c:948:3: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
gpiod_set_value_cansleep(priv->reset, 0);
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mt7530.c: In function 'mt7530_probe':
drivers/net/dsa/mt7530.c:1068:17: error: implicit declaration of function 'devm_gpiod_get_optional' [-Werror=implicit-function-declaration]
priv->reset = devm_gpiod_get_optional(&mdiodev->dev, "reset",
^~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mt7530.c:1069:13: error: 'GPIOD_OUT_LOW' undeclared (first use in this function)
GPIOD_OUT_LOW);
^~~~~~~~~~~~~
drivers/net/dsa/mt7530.c:1069:13:
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMI clause 22 & 45 read/write operations are local to the global2.c file,
so make them static. This eliminates the following warning:
drivers/net/dsa/mv88e6xxx/global2.c:571:5: warning: no previous prototype for 'mv88e6xxx_g2_smi_phy_read_c45' [-Wmissing-prototypes]
int mv88e6xxx_g2_smi_phy_read_c45(struct mv88e6xxx_chip *chip, int addr,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.c:602:5: warning: no previous prototype for 'mv88e6xxx_g2_smi_phy_read_c22' [-Wmissing-prototypes]
int mv88e6xxx_g2_smi_phy_read_c22(struct mv88e6xxx_chip *chip, int addr,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.c:635:5: warning: no previous prototype for 'mv88e6xxx_g2_smi_phy_write_c45' [-Wmissing-prototypes]
int mv88e6xxx_g2_smi_phy_write_c45(struct mv88e6xxx_chip *chip, int addr,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.c:664:5: warning: no previous prototype for 'mv88e6xxx_g2_smi_phy_write_c22' [-Wmissing-prototypes]
int mv88e6xxx_g2_smi_phy_write_c22(struct mv88e6xxx_chip *chip, int addr,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MT7530 is a 7-ports Gigabit Ethernet Switch that could be found on
Mediatek router platforms such as MT7623A or MT7623N platform which
includes 7-port Gigabit Ethernet MAC and 5-port Gigabit Ethernet PHY.
Among these ports, The port from 0 to 4 are the user ports connecting
with the remote devices while the port 5 and 6 are the CPU ports
connecting into Mediatek Ethernet GMAC.
For port 6, it can communicate with the CPU via Mediatek Ethernet GMAC
through either the TRGMII or RGMII which could be controlled by phy-mode
in the dt-bindings to specify which mode is preferred to use. And for
port 5, only RGMII can be specified. However, currently, only port 6 is
being supported in this DSA driver.
The driver is made with the reference to qca8k and other existing DSA
driver. The most of the essential callbacks of the DSA are already
support in the driver, including tag insert for user port distinguishing,
port control, bridge offloading, STP setup and ethtool operation to allow
DSA to model each user port into a standalone netdevice as the other DSA
driver had done.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan's static checker reported the following:
drivers/net/dsa/dsa_loop.c:223 dsa_loop_port_vlan_dump()
error: uninitialized symbol 'err'.
which could happen if we do hit the continue statement for each iteration of
the loop. Initialize err to 0 here.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 98cd1552ea ("net: dsa: Mock-up driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan's static analyzer reported the following:
drivers/net/dsa/dsa_loop.c:181 dsa_loop_port_vlan_del()
error: XXX uninitialized symbol 'pvid'.
we were missing the assignment of pvid to ps->vid, so add that.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 98cd1552ea ("net: dsa: Mock-up driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a DSA mock-up driver which essentially does
the following:
- registers/unregisters 4 fixed PHYs to the slave network devices
- uses eth0 (configurable) as the master netdev
- registers the switch as a fixed MDIO device against the fixed MDIO bus
at address 31
- includes dynamic debug prints for dsa_switch_ops functions that can be
enabled to get call traces
This is a good way to test modular builds as well as exercise the DSA
APIs without requiring access to real hardware. This does not test the
data-path, although this could be added later on.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the DSA cross-chip bridging operations by remapping the local
ports an external source port can egress frames to, when this cross-chip
port joins or leaves a bridge.
The PVT is no longer configured with all ones allowing any external
frame to egress any local port. Only DSA and CPU ports, as well as
bridge group members, can egress frames on local ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a local port of a switch chip becomes a member of a bridge group,
we need to reprogram the Cross-chip Port Based VLAN Table (PVT) to allow
existing cross-chip bridge members to egress frames on the new ports.
There is no functional changes yet, since the PVT is still programmed
with all ones, allowing any external port to egress frames locally.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factorize the code in the DSA port_bridge_{join,leave} routines used to
program the port VLAN map of all local ports of a given bridge group.
At the same time shorten the _mv88e6xxx_port_based_vlan_map to get rid
of the old underscore prefix naming convention.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All ports -- internal and external, for chips featuring a PVT -- have a
mask restricting to which internal ports a frame is allowed to egress.
Now that DSA exposes the number of ports and their bridge devices, it is
possible to extract the code generating the VLAN map and make it generic
so that it can be shared later with the cross-chip bridging code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
