Past evidence with system hangs and hsds tie
WaForceEnableNonCoherent and WaDisableHDCInvalidation to
WaForceContextSaveRestoreNonCoherent. Documentation
states that WaForceContextSaveRestoreNonCoherent would
not be needed on skl past E0 but evidence proved otherwise. See
commit <510650e8b2ab> ("drm/i915/skl: Fix spurious gpu hang with gt3/gt4
revs"). In this scope consider kbl to be skl with a bigger revision than
E0 so play it safe and bind these two workarounds to the
WaForceContextSaveRestoreNonCoherent, and apply to all gen9.
v2: fix comment (Matthew)
References: HSD#2134449, HSD#2131413
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-7-git-send-email-mika.kuoppala@intel.com
We need to disable clock gating in this unit to work around
hardware issue causing possible corruption/hang.
v2: name the bit (Ville)
v3: leave the fix enabled for 2227050 and set correct bit (Matthew)
References: HSD#2227156, HSD#2227050
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-2-git-send-email-mika.kuoppala@intel.com
The atomic version of intel_pre_plane_update did not check
for HAS_GMCH_DISPLAY before calling intel_set_memory_cxsr().
While this doesn't cause any issues on its own (it will
return without doing anything if the hardware doesn't
have the required feature), the drm_wait_one_vblank() that
is needed if memory self-refresh is disabled introduces
an unnecessary delay in the suspend path.
In cases where i915 is on the critical path it means that
we slow down suspend by 16.8ms on platforms that don't
need to disable memory self-refresh.
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463662236-18192-1-git-send-email-david.weinehall@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Apparently some CHV boards failed to hook up the port presence straps
for HDMI ports as well (earlier we assumed this problem only affected
eDP ports). So let's check the VBT in addition to the strap, and if
either one claims that the port is present go ahead and register the
relevant connector.
While at it, change port D to register DP before HDMI as we do for ports
B and C since
commit 457c52d87e ("drm/i915: Only ignore eDP ports that are connected")
Also print a debug message when we register a HDMI connector to aid
in diagnosing missing/incorrect ports. We already had such a print for
DP/eDP.
v2: Improve the comment in the code a bit, note the port D change in
the commit message
Cc: Radoslav Duda <radosd@radosd.com>
Tested-by: Radoslav Duda <radosd@radosd.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96321
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464945463-14364-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The recent patch
. fce91f2 drm/i915/guc: add enable_guc_loading parameter
enabled GuC loading and submission by default, but as issues
were found with warnings being issued during suspend-resume
cycles, GuC loading was disabled by default, by patch
. 2335986 drm/i915/guc: Disable automatic GuC firmware loading
Those warnings have been resolved, so this patch re-enables GuC
loading and submission by default.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465287291-2187-1-git-send-email-david.s.gordon@intel.com
When resetting and reloading the GuC, the GuC submission management code
also needs to destroy and recreate the GuC client(s). Currently this is
done by a separate call from the GuC loader, but really, it's just an
internal detail of the submission code. So here we remove the call from
the loader (which is too late, really, because the GuC has already been
reloaded at this point) and put it into guc_submission_init() instead.
This means that any preexisting client is destroyed *before* the GuC
(re)load and then recreated after, iff the firmware was successfully
loaded. If the GuC reload fails, we don't recreate the client, so
fallback to execlists mode (if active) won't leak the client object
(previously, the now-unusable client would have been left allocated,
and leaked if the driver were unloaded).
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
The last stage of the GuC loader also sanitises the GuC submission
settings, so should be called unconditionally (even on platforms
without a GuC) to ensure consistent settings; in particular, this
prevents any attempt to use GuC submission on GuCless platforms!
Also fix error path handling and clarify DRM_INFO fallback message.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fix the failure mode where the display appears split, or shifted about
2/3 of the screen, and the color components are cycled. Turns out we
were missing the crucial BXT_DEFEATURE_DPI_FIFO_CTR bit in the
EOT_DISABLE register.
Per bspec, with the bit set, the "mipi_dpf_vblank_start" signal is
asserted only when the complete frame is transferred in the DPHY line
and also the DPI FIFO is flushed out at the end of each frame.
The problem was mitigated by keeping the panel fitter enabled, but that
only limited the issue to a shift of about 0..10 pixels. With the fix
here, the panel fitter workaround does not seem to be needed at all.
While at it, set BXT_DPHY_DEFEATURE_EN in EOT_DISABLE register which is
also needed per the BXT DSI mode set sequence.
Issue: VIZ-7610
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464965825-31035-1-git-send-email-jani.nikula@intel.com
The VBT has these mysterious H/V image sizes as part of the display
timings. Looking at some dumps those appear to be the physical
dimensions in mm. Which makes sense since the timing descriptor matches
the format used by EDID detailed timing descriptor, which defines these
as "H/V Addressable Video Image Size in mm".
So let's use that information from the panel fixed mode to get the
physical dimensions for LVDS/eDP/DSI displays. And with that we can
fill out the display_info so that userspace can get at it via
GetConnector.
v2: Use (hi<<8)|lo instead of broken (hi<<4)+lo
Handle LVDS and eDP too
Cc: Stephen Just <stephenjust@gmail.com>
Tested-by: Stephen Just <stephenjust@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96255
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464685714-30507-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
My old 845g complains that the child_device_size inside its VBT,
version 110, is incorrect. Let's fiddle with the version matching such
that it works with this VBT (i.e. treat BIOS v110 as having the same size
as v108).
Fixes [drm:intel_bios_init] *ERROR* Unexpected child device config
size 27 (expected 33 for VBT version 110)
Whether this is correct, no one knows - but it works for this particular
machine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464800923-6054-1-git-send-email-chris@chris-wilson.co.uk
Git got absolutely destroyed with all our cherry-picking from
drm-intel-next-queued to various branches. It ended up inserting
intel_crtc_page_flip 2x even in intel_display.c.
Backmerge to get back to sanity.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
drm-intel-next-2016-05-22:
- cmd-parser support for direct reg->reg loads (Ken Graunke)
- better handle DP++ smart dongles (Ville)
- bxt guc fw loading support (Nick Hoathe)
- remove a bunch of struct typedefs from dpll code (Ander)
- tons of small work all over to avoid casting between drm_device and the i915
dev struct (Tvrtko&Chris)
- untangle request retiring from other operations, also fixes reset stat corner
cases (Chris)
- skl atomic watermark support from Matt Roper, yay!
- various wm handling bugfixes from Ville
- big pile of cdclck rework for bxt/skl (Ville)
- CABC (Content Adaptive Brigthness Control) for dsi panels (Jani&Deepak M)
- nonblocking atomic commits for plane-only updates (Maarten Lankhorst)
- bunch of PSR fixes&improvements
- untangle our map/pin/sg_iter code a bit (Dave Gordon)
drm-intel-next-2016-05-08:
- refactor stolen quirks to share code between early quirks and i915 (Joonas)
- refactor gem BO/vma funcstion (Tvrtko&Dave)
- backlight over DPCD support (Yetunde Abedisi)
- more dsi panel sequence support (Jani)
- lots of refactoring around handling iomaps, vma, ring access and related
topics culmulating in removing the duplicated request tracking in the execlist
code (Chris & Tvrtko) includes a small patch for core iomapping code
- hw state readout for bxt dsi (Ramalingam C)
- cdclk cleanups (Ville)
- dedupe chv pll code a bit (Ander)
- enable semaphores on gen8+ for legacy submission, to be able to have a direct
comparison against execlist on the same platform (Chris) Not meant to be used
for anything else but performance tuning
- lvds border bit hw state checker fix (Jani)
- rpm vs. shrinker/oom-notifier fixes (Praveen Paneri)
- l3 tuning (Imre)
- revert mst dp audio, it's totally non-functional and crash-y (Lyude)
- first official dmc for kbl (Rodrigo)
- and tons of small things all over as usual
* 'drm-intel-next' of git://anongit.freedesktop.org/drm-intel: (194 commits)
drm/i915: Revert async unpin and nonblocking atomic commit
drm/i915: Update DRIVER_DATE to 20160522
drm/i915: Inline sg_next() for the optimised SGL iterator
drm/i915: Introduce & use new lightweight SGL iterators
drm/i915: optimise i915_gem_object_map() for small objects
drm/i915: refactor i915_gem_object_pin_map()
drm/i915/psr: Implement PSR2 w/a for gen9
drm/i915/psr: Use ->get_aux_send_ctl functions
drm/i915/psr: Order DP aux transactions correctly
drm/i915/psr: Make idle_frames sensible again
drm/i915/psr: Try to program link training times correctly
drm/i915/userptr: Convert to drm_i915_private
drm/i915: Allow nonblocking update of pageflips.
drm/i915: Check for unpin correctness.
Reapply "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
drm/i915: Make unpin async.
drm/i915: Prepare connectors for nonblocking checks.
drm/i915: Pass atomic states to fbc update functions.
drm/i915: Remove reset_counter from intel_crtc.
drm/i915: Remove queue_flip pointer.
...
Frist -misc pull for 4.8, with pretty much just random all over plus a few
more lockless gem BO patches acked/reviewed by driver maintainers.
I'm starting a bit earlier this time around because there's a few invasive
patch series to land (nonblocking atomic prep work, fence prep work,
rst/sphinx kerneldoc finally happening) and I need a baseline with all the
branches merged.
* tag 'topic/drm-misc-2016-06-01' of git://anongit.freedesktop.org/drm-intel: (21 commits)
drm/vc4: Use lockless gem BO free callback
drm/vc4: Use drm_gem_object_unreference_unlocked
drm: Initialize a linear gamma table by default
drm/vgem: Use lockless gem BO free callback
drm/qxl: Don't set a gamma table size
drm/msm: Nuke dummy gamma_set/get functions
drm/cirrus: Drop redundnant gamma size check
drm/fb-helper: Remove dead code in setcolreg
drm/mediatek: Use lockless gem BO free callback
drm/hisilicon: Use lockless gem BO free callback
drm/hlcd: Use lockless gem BO free callback
vga_switcheroo: Support deferred probing of audio clients
vga_switcheroo: Add helper for deferred probing
virtio-gpu: fix output lookup
drm/doc: Unify KMS Locking docs
drm/atomic-helper: Do not call ->mode_fixup for CRTC which will be disabled
Fix annoyingly awkward typo in drm_edid_load.c
drm/doc: Drop vblank_disable_allow wording
drm: use seqlock for vblank time/count
drm/mm: avoid possible null pointer dereference
...
if downscaling is enabled plane data rate increases according to scaling
amount. take scaling amount under consideration while calculating plane
data rate
v2: Address Matt's comments, where data rate was overridden because of
missing else.
v3 (by Matt):
- Add braces to 'else' branch to match kernel coding style
- Adjust final calculation now that skl_plane_downscale_amount()
returns 16.16 fixed point value instead of a decimal fixed point
v4 (by Matt):
- Avoid integer overflow by making sure final multiplication is
treated as 64-bit.
Cc: matthew.d.roper@intel.com
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463695381-21368-1-git-send-email-matthew.d.roper@intel.com
Don't use pipe pixel rate for plane pixel rate. Calculate plane pixel according
to formula
adjusted plane_pixel_rate = adjusted pipe_pixel_rate * downscale ammount
downscale amount = max[1, src_h/dst_h] * max[1, src_w/dst_w]
if 90/270 rotation use rotated width & height
v2: use intel_plane_state->visible instead of (fb == NULL) as per Matt's
comment.
v3 (by Matt):
- Keep downscale amount in 16.16 fixed point rather than converting to
decimal fixed point.
- Store adjusted plane pixel rate in plane state instead of the plane
parameters structure that we no longer use.
v4 (by Matt):
- Significant rebasing onto latest atomic watermark work
- Don't bother storing plane pixel rate in state; just calculate it
right before the calls that make use of it.
- Fix downscale calculations to actually use width values when
computing downscale_w rather than copy/pasted height values.
Cc: matthew.d.roper@intel.com
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463439121-28974-4-git-send-email-matthew.d.roper@intel.com
don't always use 8 ddb as minimum, instead calculate using proper
algorithm.
v2: optimizations as per Matt's comments.
v3 (by Matt):
- Fix boolean logic for !fb test in skl_ddb_min_alloc()
- Adjust negative tiling format comparisons in skl_ddb_min_alloc() to
improve readability.
v4 (by Matt):
- Rebase onto recent atomic watermark changes
- Slight tweaks to code flow to make the logic more closely match the
description in the bspec.
v5 (by Matt):
- Handle minimum scanline calculation properly for 4 & 8 bpp formats.
8bpp isn't actually possible right now, but it's listed in the bspec
so I've included it here for forward compatibility (similar to how
we have logic for NV12).
v6 (by Matt):
- Calculate plane_bpp correctly for non-NV12 formats. (Mahesh)
Cc: matthew.d.roper@intel.com
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464713939-10440-1-git-send-email-matthew.d.roper@intel.com
We don't actually read out full plane state during driver startup (only
whether the primary plane is enabled/disabled), so all of the src/dest
rectangles are invalid at this point. However this calculation was
needless anyway since we re-calculate them from scratch on the very
first atomic transaction after boot anyway.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463439121-28974-2-git-send-email-matthew.d.roper@intel.com
If the VBT says that a certain port should be eDP (and hence fused off
from HDMI), but in reality it isn't, we need to try and acquire the HDMI
connection instead. So only trust the VBT edp setting if we can connect
to an eDP device on that port.
Fixes: d2182a6608 (drm/i915: Don't register HDMI connectors for eDP ports on VLV/CHV)
References: https://bugs.freedesktop.org/show_bug.cgi?id=96288
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Phidias Chiang <phidias.chiang@canonical.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464766070-31623-1-git-send-email-chris@chris-wilson.co.uk
This reverts the following patches:
d55dbd06bb drm/i915: Allow nonblocking update of pageflips.
15c86bdb76 drm/i915: Check for unpin correctness.
95c2ccdc82 Reapply "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
a6747b7304 drm/i915: Make unpin async.
03f476e1fc drm/i915: Prepare connectors for nonblocking checks.
2099deffef drm/i915: Pass atomic states to fbc update functions.
ee7171af72 drm/i915: Remove reset_counter from intel_crtc.
2ee004f7c5 drm/i915: Remove queue_flip pointer.
b8d2afae55 drm/i915: Remove use_mmio_flip kernel parameter.
8dd634d922 drm/i915: Remove cs based page flip support.
143f73b3bf drm/i915: Rework intel_crtc_page_flip to be almost atomic, v3.
84fc494b64 drm/i915: Add the exclusive fence to plane_state.
6885843ae1 drm/i915: Convert flip_work to a list.
aa420ddd8e drm/i915: Allow mmio updates on all platforms, v2.
afee4d8707 Revert "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
"drm/i915: Allow nonblocking update of pageflips" should have been
split up, misses a proper commit message and seems to cause issues in
the legacy page_flip path as demonstrated by kms_flip.
"drm/i915: Make unpin async" doesn't handle the unthrottled cursor
updates correctly, leading to an apparent pin count leak. This is
caught by the WARN_ON in i915_gem_object_do_pin which screams if we
have more than DRM_I915_GEM_OBJECT_MAX_PIN_COUNT pins.
Unfortuantely we can't just revert these two because this patch series
came with a built-in bisect breakage in the form of temporarily
removing the unthrottled cursor update hack for legacy cursor ioctl.
Therefore there's no other option than to revert the entire pile :(
There's one tiny conflict in intel_drv.h due to other patches, nothing
serious.
Normally I'd wait a bit longer with doing a maintainer revert, but
since the minimal set of patches we need to revert (due to the bisect
breakage) is so big, time is running out fast. And very soon
(especially after a few attempts at fixing issues) it'll be really
hard to revert things cleanly.
Lessons learned:
- Not a good idea to rush the review (done by someone fairly new to
the area) and not make sure domain experts had a chance to read it.
- Patches should be properly split up. I only looked at the two
patches that should be reverted in detail, but both look like the
mix up different things in one patch.
- Patches really should have proper commit messages. Especially when
doing more than one thing, and especially when touching critical and
tricky core code.
- Building a patch series and r-b stamping it when it has a built-in
bisect breakage is not a good idea.
- I also think we need to stop building up technical debt by
postponing atomic igt testcases even longer. I think it's clear that
there's enough corner cases in this beast that we really need to
have the testcases _before_ the next step lands.
(cherry picked from commit 5a21b6650a
from drm-intel-next-queeud)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
On Loading, GuC sets PM interrupts routing (bit 31) and clears ARAT
expired interrupt (bit 9). Host turbo also updates this register
in RPS flows. This patch ensures bit 31 and bit 9 setup by GuC persists.
ARAT timer interrupt is needed in GuC for various features. It also
facilitates halting GuC and hence achieving RC6. PM interrupt routing
will not impact RPS interrupt reception by host as GuC will redirect
them.
This patch fixes igt test pm_rc6_residency that was failing with guc
load/submission enabled. Tested with SKL GuC v6.1 and BXT GuC v5.1 and v8.7.
v2: i915_irq/i915_pm decoupling from intel_guc. (ChrisW)
v3: restructuring the mask update and rebase w.r.t Ville's patch. (ChrisW)
v4: Updating the pm_intr_keep during direct_interrupts_to_guc. (Sagar)
Cc: Chris Harris <chris.harris@intel.com>
Cc: Zhe Wang <zhe1.wang@intel.com>
Cc: Deepak S <deepak.s@intel.com>
Cc: Satyanantha, Rama Gopal M <rama.gopal.m.satyanantha@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Testcase: igt/pm_rc6_residency
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Tested-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464683307-19475-1-git-send-email-sagar.a.kamble@intel.com
Since my last struct_mutex crusade someone escaped!
This already has the advantage that for the common case when someone
else holds a ref the unref won't even acquire dev->struct_mutex. And
I'm working on code to allow drivers to completely opt-out of any and
all dev->struct_mutex usage, but that only works if they use the
_unlocked variants everywhere.
v2: Drop comment too.
v3: Drop the other comment too.
Cc: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464630800-30786-15-git-send-email-daniel.vetter@ffwll.ch
Code stolen from gma500.
This is just a minor bit of safety code that I spotted and figured it
might be useful if we put it into the core. This is to make the
get_gamma ioctl reflect likely reality even before the first set_gamma
ioctl call.
v2 on irc: Extend commit message per Maarten's suggestions.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459331485-28376-2-git-send-email-daniel.vetter@ffwll.ch
qxl doesn't have any functions for setting the gamma table, so this is
completely defunct.
Not nice to lie to userspace, so let's stop!
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1459331485-28376-10-git-send-email-daniel.vetter@ffwll.ch
Again the fbdev emulation gamma_set/get functions are only needed for
drivers that try to also use 8bpp paletted mode. Which msm doesn't, so
this is dead code. Let's rip it out.
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1459331485-28376-7-git-send-email-daniel.vetter@ffwll.ch
DRM fbdev emulation only supports pallete_color with depth == 8, and
truecolor with depth > 8. Handling depth == 16 for palettes is hence
dead code, let's remove it.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1459331485-28376-3-git-send-email-daniel.vetter@ffwll.ch
Daniel Vetter pointed out that vga_switcheroo_client_probe_defer() could
be needed by audio clients as well. To avoid mistakes when someone adds
conditions for these in the future, constrain the single existing
condition to VGA clients by checking for PCI_BASE_CLASS_DISPLAY. This
encompasses both PCI_CLASS_DISPLAY_VGA as well as PCI_CLASS_DISPLAY_3D,
which is used by some Nvidia Optimus GPUs.
Any future checks for audio clients should then be constrained to
PCI_BASE_CLASS_MULTIMEDIA.
v6: Spun out from commit introducing vga_switcheroo_client_probe_defer()
to keep it a pure refactoring change. (Emil Velikov, Jani Nikula)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/358d58490eb9dda5f270d844b0dce511a2a20828.1464685538.git.lukas@wunner.de
So far we've got one condition when DRM drivers need to defer probing
on a dual GPU system and it's coded separately into each of the relevant
drivers. As suggested by Daniel Vetter, deduplicate that code in the
drivers and move it to a new vga_switcheroo helper. This yields better
encapsulation of concepts and lets us add further checks in a central
place. (The existing check pertains to pre-retina MacBook Pros and an
additional check is expected to be needed for retinas.)
One might be tempted to check deferred probing conditions in
vga_switcheroo_register_client(), but this is usually called fairly late
during driver load. The GPU is fully brought up and ready for switching
at that point. On boot the ->probe hook is potentially called dozens of
times until it finally succeeds, and each time we'd repeat bringup and
teardown of the GPU, lengthening boot time considerably and cluttering
logfiles. A separate helper is therefore needed which can be called
right at the beginning of the ->probe hook.
Note that amdgpu currently does not call this helper as the AMD GPUs
built into MacBook Pros are only supported by radeon so far.
v2: This helper could eventually be used by audio clients as well,
so rephrase kerneldoc to refer to "client" instead of "GPU"
and move the single existing check in an if block specific
to PCI_CLASS_DISPLAY_VGA devices. Move documentation on
that check from kerneldoc to a comment. (Daniel Vetter)
v3: Mandate in kerneldoc that registration of client shall only
happen after calling this helper. (Daniel Vetter)
v4: Rebase on 412c8f7de0 ("drm/radeon: Return -EPROBE_DEFER when
amdkfd not loaded")
v5: Some Optimus GPUs use PCI_CLASS_DISPLAY_3D, make sure those are
matched as well. (Emil Velikov)
v6: The if-condition referring to PCI_BASE_CLASS_DISPLAY may be
considered a functional change. Move to a separate commit to
keep this a pure refactoring change. (Emil Velikov, Jani Nikula)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/575885fd440c2b13c3f19ddf44360cfbbff35f50.1464685538.git.lukas@wunner.de
Rather than let the core generate usless encoder names, let's pass in
something that actually identifies the piece of hardware we're dealing
with.
v2: Use 'DSI %c' instead of 'MIPI %c' for DSI encoders (Jani)
v3: Use port_name() in DSI code since we have it
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-7-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Let's name our planes in a way that makes sense wrt. the spec:
- skl+ -> "plane 1A", "plane 2A", "plane 1C", "cursor A" etc.
- g4x+ -> "primary A", "primary B", "sprite A", "cursor C" etc.
- pre-g4x -> "plane A", "cursor B" etc.
v2: Rebase on top of the fixed/cleaned error paths
Use a local 'name' variable to make things easier
v3: Pass the name as a function argument to drm_universal_plane_init() (Jani)
v3: Pass the printf style string to drm_universal_plane_init()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Call intel_plane_destroy() instead of drm_plane_cleanup() so that we
also free the plane struct itself when bailing out of the crtc init.
And make intel_plane_destroy() NULL tolerant to avoid having to check
for it in the caller.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
v2: Fix intel_crtc leak on failure to allocate the name
Use a local 'name' variable to make things easier
v3: Pass the name as a function arguemnt to drm_crtc_init_with_planes() (Jani)
v4: Pass the printf style format string to drm_crtc_init_with_planes()
v5: Drop spurious code changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
When a CRTC is going to be disabled, it's state may contain a display mode
with zeroed content. This could be reproduced by HDMI cable hotplug out
operation with legacy fbdev support in dual display cases. It would confuse
driver's CRTC callback ->mode_fixup and make the total state be rejected.
So, let's don't call the callback for the CRTC.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1464341754-7087-1-git-send-email-gnuiyl@gmail.com
