The phyCORE-AM335x development kit is a combination of the
phyCORE-AM335x SoM and a PCM-953 carrier board. The features
of the PCM-953 are:
* ETH phy on carrier board: 1x RGMII
* 1x CAN
* Up to 4x UART
* USB0 (otg)
* USB1 (host)
* SD slot
* User gpio-keys
* User LEDs
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA72 and DRA718 EVM boards has a pcf8575 gpio expander
which is used for the LCD/LEDs and USB vbus detection.
Add the node for the pcf8575.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Tested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the ISL29023 ALS connected via the I2C bus.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the 16-Bit I/O Expander connected via the I2C bus.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the BQ32000 Real Time Clock connected to the I2C bus
and disable the AM335x Real Time Clock.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the 32Mb Serial Flash Memory connected to SPI0
and using CS1.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The UART1 is connected to the infrared (IR) receiver module, so enable it
to be able to comunicate with it.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I2C1 is not used so remove it in order to avoid conflicts.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
FDT harcoded partition table does not match that one in historical
TI's 2.6.37 kernel and non legacy kernels even use different ECC scheme,
yet noone complained, so remove it altogether.
Also, UBI volumes instead of partitions are used since u-boot-2016.09.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to errata i880 description the speed of Ethernet port 1 on AM572x
SoCs rev 1.1 should be limited to 10/100Mbps, because RGMII2 Switching
Characteristics are not compatible with 1000 Mbps operation [1].
The issue is fixed with Rev 2.0 silicon.
Hence, rework Beagle-X15 and Begale-X15-revb1 to use phy-handle instead of
phy_id and apply corresponding limitation to the Ethernet Phy 1.
[1] http://www.ti.com/lit/er/sprz429j/sprz429j.pdf
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As the bootloader passes the NAND and the SPI flash partition tables
there is no need to keep them in the kernel device tree.
Removed them.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
TI DRA72-EVM Rev C has two DP83867 ethernet phys which support IRQ
generation in case of phy/link status changes. The INT/PWDN lines from both
DP83867 phys are wired to DRA7 gpio6.16, so reflect the same in DT.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is slightly different wiring compared to omap5-uevm or pandaboard:
/sys/bus/usb/devices/3-2 hub
/sys/bus/usb/devices/3-2.3 7500
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Note that with 9730 the wiring is different compared to 9514 found on
beagleboard xm for example.
On beagleboard xm we have:
/sys/bus/usb/devices/1-2 hub
/sys/bus/usb/devices/1-2.1 9514
While on omap5-uevm we have:
/sys/bus/usb/devices/1-2 hub
/sys/bus/usb/devices/1-3 9730
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Inspired by a patch for beagleboard xm by Laurent Pinchart
<laurent.pinchart@ideasonboard.com>, similar patch also works for
pandaboard. The only difference is that the hub is address 1 instead
of 2.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Beagleboard-xM has a LAN9514 USB hub and ethernet controller,
connected to port 2 of the OMAP EHCI controller. The board however has
no EEPROM to store the ethernet MAC address, which is programmed by the
boot loader.
To allow Linux to use the same MAC address as the boot loader (or for
that matter any fixed MAC address), we need a node in the device tree
for the ethernet controller that the boot loader can update at runtime
with a local-mac-address property. Add it, along with an alias for the
ethernet controller to let the boot loader locate it easily.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Set USB0 to otg mode (default) and not fix to peripheral.
As it can be used in host mode also.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include the i2c temperature sensor which is optionaly mounted
on the phyCORE-AM335x-R2 module.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As we may have different SPI NOR flashes with 8MB populated on
phyCORE-AM335x SOM, set the "jedec,spi-nor" SPI Flash compatible string.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
From v4.2+ the GPMC code has been changed to reset all the bootloader
GPMC settings when the kernel starts.
As such, this DTS file now needs the external FRAM defined.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For the existing IOdelay configuration via U-Boot, NAND is
not supported on dra72-evm (both Rev B and Rev C).
Disable it. Commit 46cfc89458 ("ARM: dts: dra72-evm: Remove
pinmux configurations for erratum i869") has already removed
pinmuxing for NAND making it unusable.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinmux configuration for SD card slot and eMMC device
found on TI's DRA74x EVM.
Only the default modes are supported. For higher speed modes
(UHS and HS200) to function, we need full fledged IODelay support
in kernel. IODelay support is yet to be added.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[nsekhar@ti.com: rebase to mainline/master, use IOPAD() macro,
update commit message]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pinmuxing for DRA7x/AM57x family of processors need to be done in IO
isolation as part of initial bootloader executed from SRAM. This is
done as part of iodelay configuration sequence and is required due
to the limitations introduced by erratum ID: i869[1] (IO Glitches
can occur when changing IO settings) and elaborated in the Technical
Reference Manual[2] 18.4.6.1.7 Isolation Requirements.
Only peripheral that is permitted for dynamic pin mux configuration
is MMC and DCAN. MMC is permitted to change to accommodate the
requirements for varied speeds (which require IO-delay support in
kernel as well). DCAN is a result of i893[1] (DCAN initialization
sequence).
DCAN pinmux is retained in this patch. MMC pinmux is missing from
the dra7-evm.dts file and the board is relying on configuration done
by bootloader. A subsequent patch will add MMC pinmux configuration.
A side-effect of this patch is that NAND support is removed. NAND
pins clash with VOUT3 on DRA7-EVM. U-Boot selects VOUT3 over NAND
as per TI EVM application needs.
[1] http://www.ti.com/lit/pdf/sprz429
[2] http://www.ti.com/lit/pdf/sprui30
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On chiliSOM TPS65217 nWAKEUP pin is connected to AM335x internal RTC
EXT_WAKEUP input. In RTC-only state TPS65217 is notifying about power on
events (such as power buton presses) by setting nWAKEUP output
low. After that it waits 5s for proper device boot. Currently it doesn't
happen, as the processor doesn't listen for such events. Consequently
TPS65217 changes state from SLEEP (RTC-only state) to OFF.
Enable EXT_WAKEUP input of AM335x's RTC, so the processor can properly
detect power on events and recover immediately from RTC-only states,
without powering off RTC and losing time.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix GPIO comment to be consistent with rest of file and add comment what
tpa6130 is.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Reviewed-By: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
SeeedStudio BeagleBone Green Wireless (BBGW) is an expansion of the
SeeedStudio Green (BBG) with the Ethernet replaced by a TI wl1835
wireless module.
This board can be indentified by the GW1x value after A335BNLT (BBB)
in the at24 eeprom:
GW1x [aa 55 33 ee 41 33 33 35 42 4e 4c 54 47 57 31 41 |.U3.A335BNLTGW1A|]
http://beagleboard.org/green-wirelesshttp://wiki.seeed.cc/BeagleBone_Green_Wireless/
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: Stored in at24 eeprom at address 5-16:
hexdump -e '8/1 "%c"' /sys/bus/i2c/devices/0-0050/eeprom | cut -b 5-16
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is going to be shared with the SeeedStudio BeagleBone Green Wireless
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with
the Ethernet replaced by a TI wl1835 wireless module.
This board can be indentified by the BWAx value after A335BNLT (BBB)
in the at24 eeprom:
BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
http://beagleboard.org/black-wirelesshttps://github.com/beagleboard/beaglebone-black-wireless
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
Acked-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is going to be shared with the BeagleBone Black Wireless
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SoC hix5hd2 compatible string has the suffix "-gmac" and
we should not change it.
We should only add the generic compatible string "hisi-gmac-v1".
Fixes: 0855950ba5 ("ARM: dts: hix5hd2: add gmac generic compatible and clock names")
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where things
come together.
We get a DT descriptions for a couple of new SoCs, all of them variants
of other chips we already support, and usually coming with a new
evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers
or industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on
Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it into
products and have served their purpose in the kernel as a template
for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree
Conflicts:
arch/arm/boot/dts/r8a*.dtsi: a node was added
the clk tree, keep both sides and watch out for git
dropping the required '};' at the end of each side.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wJt3
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where
things come together.
We get a DT descriptions for a couple of new SoCs, all of them
variants of other chips we already support, and usually coming with a
new evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers or
industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it
into products and have served their purpose in the kernel as a
template for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits)
arm: dts: zynq: Add MicroZed board support
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: artpec: add pcie support
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
ARM: dts: berlin2q-marvell-dmp: fix regulators' name
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM: dts: r8a7794: Add device node for PRR
ARM: dts: r8a7793: Add device node for PRR
ARM: dts: r8a7792: Add device node for PRR
ARM: dts: r8a7791: Add device node for PRR
ARM: dts: r8a7790: Add device node for PRR
ARM: dts: r8a7779: Add device node for PRR
ARM: dts: r8a73a4: Add device node for PRR
ARM: dts: sk-rzg1e: add Ether support
ARM: dts: sk-rzg1e: initial device tree
...
As usual, we queue up a few fixes that don't seem urgent enough to go in
through -rc, or that just came a little too late given their size.
The zx fixes make the platform finally boot on real hardware, the
davinci and imx31 get the DT support working better for some of
the machines that are still normally used with classic board files.
One tegra fix is important for new bootloader versions, but the
bug has been around for a while without anyone noticing.
The other changes are mostly cosmetic.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i2l2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc, or that just came a little too late given their size.
The zx fixes make the platform finally boot on real hardware, the
davinci and imx31 get the DT support working better for some of the
machines that are still normally used with classic board files. One
tegra fix is important for new bootloader versions, but the bug has
been around for a while without anyone noticing.
The other changes are mostly cosmetic"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
arm64: tegra: Add missing Smaug revision
arm64: tegra: Add VDD_GPU regulator to Jetson TX1
arm64: dts: zte: clean up gic-v3 redistributor properties
arm64: dts: zx: Fix gic GICR property
bus: vexpress-config: fix device reference leak
soc: ti: qmss: fix the case when !SMP
ARM: lpc32xx: drop duplicate header device.h
ARM: ixp4xx: drop duplicate header gpio.h
ARM: socfpga: fix spelling mistake in error message
ARM: dts: imx6q-cm-fx6: fix fec pinctrl
ARM: dts: imx7d-pinfunc: fix UART pinmux defines
ARM: dts: imx6qp: correct LDB clock inputs
ARM: OMAP2+: pm-debug: Use seq_putc() in two functions
ARM: OMAP2+: Remove the omapdss_early_init_of() function
mfd: tps65217: Fix mismatched interrupt number
ARM: zx: Fix error handling
ARM: spear: Fix error handling
ARM: davinci: da850: Fix pwm name matching
ARM: clk: imx31: properly init clocks for machines with DT
clk: imx31: fix rewritten input argument of mx31_clocks_init()
...
Fairly routine update this time around with all changes specific to drivers.
o New driver for STMicroelectronics FDMA
o Memory-to-memory transfers on dw dmac
o Support for slave maps on pl08x devices
o Bunch of driver fixes to use dma_pool_zalloc
o Bunch of compile and warning fixes spread across drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYUg7NAAoJEHwUBw8lI4NH5/gP/j81+2RzCUX8PiLQxNUt0Vj+
tVJEizpWCwN1cnhc8ibZdI1DAwyj+GbN2lghYTjqqEng4yOm3czPzUl99grBrpQl
t+Qylr9PSpck/paRhd2lgZzG8Nk+B5HJDcxBQbW4pwmbc69YAbqYzt44i4bDpR5K
u3mBve1Ulng7peP45EZB8BA32ffCpOEAC/9SdkaPokrSv6XxxPEFvzewy+mLtioU
a0zY0iuHqVGpOTABK65fXO/zkGiZLPXJ1T5vK7Iz8mOwuvtYVif0yktQSrx3BWbc
9r64W7Si633wWt/C9LkuMMSmQ7nI/PyHk811cDOcxp3SA79JV5SWwdQl+5QPdtoP
hyToaISfAY0BiNI9ltdscx3MPjlwSp08xXvi46RjSs8E2TXnbHUw+J5mTsxYuocl
Yi61nlL5ClhCbySf9Q3GFsuAJ3O2Nq9WkCTNRIvJtrMhe3NeqDDTfBZJRD4Bfg1G
q8RAc5oqGZDtqKHtLfwULr7Ec2Ru0hIZAyN907OwW+4jBR/eBJB1y+nGrNPtTWPT
OOcvrxe85/+ZNROGCZKr0L8UA/MBBMZtjvMY8RMXjBE4YJbakq7tV+7l5VolKeNH
G6I/1CC06qVPHrnetM6YejhtnmOQ4F8P1sE0wvpG0QTyHJoFq+aOhHNKJC8F9Eln
CQM2apvL4BHvS7OHt9XL
=Pf0d
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.10-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"Fairly routine update this time around with all changes specific to
drivers:
- New driver for STMicroelectronics FDMA
- Memory-to-memory transfers on dw dmac
- Support for slave maps on pl08x devices
- Bunch of driver fixes to use dma_pool_zalloc
- Bunch of compile and warning fixes spread across drivers"
[ The ST FDMA driver already came in earlier through the remoteproc tree ]
* tag 'dmaengine-4.10-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (68 commits)
dmaengine: sirf-dma: remove unused ‘sdesc’
dmaengine: pl330: remove unused ‘regs’
dmaengine: s3c24xx: remove unused ‘cdata’
dmaengine: stm32-dma: remove unused ‘src_addr’
dmaengine: stm32-dma: remove unused ‘dst_addr’
dmaengine: stm32-dma: remove unused ‘sfcr’
dmaengine: pch_dma: remove unused ‘cookie’
dmaengine: mic_x100_dma: remove unused ‘data’
dmaengine: img-mdc: remove unused ‘prev_phys’
dmaengine: usb-dmac: remove unused ‘uchan’
dmaengine: ioat: remove unused ‘res’
dmaengine: ioat: remove unused ‘ioat_dma’
dmaengine: ioat: remove unused ‘is_raid_device’
dmaengine: pl330: do not generate unaligned access
dmaengine: k3dma: move to dma_pool_zalloc
dmaengine: at_hdmac: move to dma_pool_zalloc
dmaengine: at_xdmac: don't restore unsaved status
dmaengine: ioat: set error code on failures
dmaengine: ioat: set error code on failures
dmaengine: DW DMAC: add multi-block property to device tree
...
Here's the big set of USB/PHY patches for 4.10-rc1.
A number of new drivers are here in this set of changes. We have a new
USB controller type "mtu3", a new usb-serial driver, and the usual churn
in the gadget subsystem and the xhci host controller driver, along with
a few other new small drivers added. And lots of little other changes
all over the USB and PHY driver tree. Full details are in the shortlog
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWFAxRg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynuLgCgsHgM/oba6UaVm1kmyN9V5e3PVjEAn34tRLht
R4enLi8Yv1bOWPdlrpzN
=3MGJ
-----END PGP SIGNATURE-----
Merge tag 'usb-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here's the big set of USB/PHY patches for 4.10-rc1.
A number of new drivers are here in this set of changes. We have a new
USB controller type "mtu3", a new usb-serial driver, and the usual
churn in the gadget subsystem and the xhci host controller driver,
along with a few other new small drivers added. And lots of little
other changes all over the USB and PHY driver tree. Full details are
in the shortlog
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (309 commits)
USB: serial: option: add dlink dwm-158
USB: serial: option: add support for Telit LE922A PIDs 0x1040, 0x1041
USB: OHCI: nxp: fix code warnings
USB: OHCI: nxp: remove useless extern declaration
USB: OHCI: at91: remove useless extern declaration
usb: misc: rio500: fix result type for error message
usb: mtu3: fix U3 port link issue
usb: mtu3: enable auto switch from U3 to U2
usbip: fix warning in vhci_hcd_probe/lockdep_init_map
usb: core: usbport: Use proper LED API to fix potential crash
usbip: add missing compile time generated files to .gitignore
usb: hcd.h: construct hub class request constants from simpler constants
USB: OHCI: ohci-pxa27x: remove useless functions
USB: OHCI: omap: remove useless extern declaration
USB: OHCI: ohci-omap: remove useless functions
USB: OHCI: ohci-s3c2410: remove useless functions
USB: cdc-acm: add device id for GW Instek AFG-125
fsl/usb: Workarourd for USB erratum-A005697
usb: hub: Wait for connection to be reestablished after port reset
usbip: vudc: Refactor init_vudc_hw() to be more obvious
...
framework. The only patch that can even be considered "core" adds another
clk_get() variant. The rest of the changes are in drivers for various SoCs, and
we have a few bits for ARM shmobile architecture code (dts and mach) due to the
dependency we're breaking between shmobile architecture code and its clk
driver. Those shmobile bits have also been pulled into arm-soc tree. Here's the
summary:
Core:
- Support for devm_get_clk_from_child() used with DT bindings that have
subnodes with the 'clocks' property
New Drivers:
- Allwinner A64 (sun50i)
- i.MX imx6ull
- Socionext's UniPhier SoC CPUs
- Mediatek MT2701 SoCs
- Rockchip rk1108 SoCs
- Qualcomm MSM8994/MSM8992 SoCS
- Qualcomm RPM Clocks
- Hisilicon Hi3516CV300 and Hi3798CV200 CRG
- Oxford Semiconductor OX820 and OX810SE SoCs
- Renesas RZ/G1M and RZ/GIE SoCs
- Renesas R-Car RST driver for mode pin states
Updates:
- Four Allwinner SoCs are migrated to the new style clk driver
- Rockchip rk3399,rk3066 PLL optimizations
- i.MX LVDS display glitch fixes and AV PLL precision improvements
- Qualcomm MSM8996 GPU GDSCs, hw controlled GDSCs, and Alpha PLL support
- Explicit demodularization of always builtin drivers
- Freescale Qoriq ls1012a and ls1046a support
- Exynos 5433 parent typo fix and critical clock tagging
- Renesas r8a7743/r8a7745 CPG
- Renesas R-Car M3-W CSI2/VIN/SYS-DMAC/(H)SCIF/I2C/DRIF/gfx support
- stm32f4* LSI, LSE, RTC, and QSPI clocks
- pxa27x and pxa25x cpufreq as clks
- TI omap36xx sprz319 advisory 2.1 workaround
- Broadcom bcm2835 rate change propogation to PLLH_AUX from VEC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=RXZr
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This is a fairly quiet release. We don't have any patches to the core
framework. The only patch that can even be considered "core" adds
another clk_get() variant. The rest of the changes are in drivers for
various SoCs, and we have a few bits for ARM shmobile architecture
code (dts and mach) due to the dependency we're breaking between
shmobile architecture code and its clk driver. Those shmobile bits
have also been pulled into arm-soc tree. Here's the summary:
Core:
- Support for devm_get_clk_from_child() used with DT bindings that
have subnodes with the 'clocks' property
New Drivers:
- Allwinner A64 (sun50i)
- i.MX imx6ull
- Socionext's UniPhier SoC CPUs
- Mediatek MT2701 SoCs
- Rockchip rk1108 SoCs
- Qualcomm MSM8994/MSM8992 SoCS
- Qualcomm RPM Clocks
- Hisilicon Hi3516CV300 and Hi3798CV200 CRG
- Oxford Semiconductor OX820 and OX810SE SoCs
- Renesas RZ/G1M and RZ/GIE SoCs
- Renesas R-Car RST driver for mode pin states
Updates:
- Four Allwinner SoCs are migrated to the new style clk driver
- Rockchip rk3399,rk3066 PLL optimizations
- i.MX LVDS display glitch fixes and AV PLL precision improvements
- Qualcomm MSM8996 GPU GDSCs, hw controlled GDSCs, and Alpha PLL
support
- Explicit demodularization of always builtin drivers
- Freescale Qoriq ls1012a and ls1046a support
- Exynos 5433 parent typo fix and critical clock tagging
- Renesas r8a7743/r8a7745 CPG
- Renesas R-Car M3-W CSI2/VIN/SYS-DMAC/(H)SCIF/I2C/DRIF/gfx support
- stm32f4* LSI, LSE, RTC, and QSPI clocks
- pxa27x and pxa25x cpufreq as clks
- TI omap36xx sprz319 advisory 2.1 workaround
- Broadcom bcm2835 rate change propogation to PLLH_AUX from VEC"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (150 commits)
clk: bcm: Fix 'maybe-uninitialized' warning in bcm2835_clock_choose_div_and_prate()
clk: add devm_get_clk_from_child() API
clk: st: clk-flexgen: Unmap region obtained by of_iomap
clk: keystone: pll: Unmap region obtained by of_iomap
clk:mmp:clk-of-mmp2: Free memory and Unmap region obtained by kzalloc and of_iomap
clk:mmp:clk-of-pxa910: Free memory and Unmap region obtained by kzmalloc and of_iomap
clk: mmp: clk-of-pxa1928: Free memory obtained by kzalloc
clk: cdce925: Fix limit check
clk: bcm: Make COMMON_CLK_IPROC into a library
clk: qoriq: added ls1012a clock configuration
clk: ti: dra7: fix "failed to lookup clock node gmac_gmii_ref_clk_div" boot message
clk: bcm: Allow rate change propagation to PLLH_AUX on VEC clock
clk: bcm: Support rate change propagation on bcm2835 clocks
clk: bcm2835: Avoid overwriting the div info when disabling a pll_div clk
clk: ti: omap36xx: Work around sprz319 advisory 2.1
clk: clk-wm831x: fix a logic error
clk: uniphier: add cpufreq data for LD11, LD20 SoCs
clk: uniphier: add CPU-gear change (cpufreq) support
clk: qcom: Put venus core0/1 gdscs to hw control mode
clk: qcom: gdsc: Add support for gdscs with HW control
...
Bug report from Debian [0] shows there's minor changed model of
Linkstation LS-GL that uses the 2nd SATA port of the SoC.
So it's necessary to enable two SATA ports, though for that specific
model only the 2nd one is used.
[0] https://bugs.debian.org/845611
Fixes: b1742ffa9d ("ARM: dts: orion5x: add device tree for buffalo linkstation ls-gl")
Reported-by: Ryan Tandy <ryan@nardis.ca>
Tested-by: Ryan Tandy <ryan@nardis.ca>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The eLCDIF IP of the i.MX 7 SoC knows multiple clocks and lists them
separately:
Clock Clock Root Description
apb_clk MAIN_AXI_CLK_ROOT AXI clock
pix_clk LCDIF_PIXEL_CLK_ROOT Pixel clock
ipg_clk_s MAIN_AXI_CLK_ROOT Peripheral access clock
All of them are switched by a single gate, which is part of the
IMX7D_LCDIF_PIXEL_ROOT_CLK clock. Hence using that clock also for
the AXI bus clock (clock-name "axi") makes sure the gate gets
enabled when accessing registers.
There seem to be no separate AXI display clock, and the clock is
optional. Hence remove the dummy clock.
This fixes kernel freezes when starting the X-Server (which
disables/re-enables the display controller).
Fixes: e8ed73f691 ("ARM: dts: imx7d: add lcdif support")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
In a previous commit, I made a copy/paste error in the pinmux
definitions of UART3: PG{13,14} instead of PA{13,14}. This commit takes
care of that. I have tested this commit on Orange Pi PC and Orange Pi
Plus, and it works for these boards.
Fixes: e3d11d3c45 ("dts: sun8i-h3: add pinmux definitions for
UART2-3")
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
bias control on DA850.
- Enable high speed support on DA850 MMC/SD
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=w2Ug
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.10/dt-4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
- Add device tree nodes for pin pull-up/pull-down
bias control on DA850.
- Enable high speed support on DA850 MMC/SD
* tag 'davinci-for-v4.10/dt-4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
Signed-off-by: Olof Johansson <olof@lixom.net>