If ubi_thread() exits but kthread_should_stop() is not true
then kthread_stop() will never return and cleanup thread
will forever stay in "D" state.
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
'ubi_io_read_data()' may return EBADMSG in case of an ECC error,
and we should not panic because of this. We have CRC32 checksum
and may check the data. So just ignore the EBADMSG error.
This patch also fixes a minor spelling error at the same time.
Signed-off-by: Zoltan Sogor <weth@inf.u-szeged.hu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
For "unlock" cycles to 16bit devices in 8bit compatibility mode we need
to use the byte addresses 0xaaa and 0x555. These effectively match
the word address 0x555 and 0x2aa, except the latter has its low bit set.
Most chips don't care about the value of the 'A-1' pin in x8 mode,
but some -- like the ST M29W320D -- do. So we need to be careful to
set it where appropriate.
cfi_send_gen_cmd is only ever passed addresses where the low byte
is 0x00, 0x55 or 0xaa. Of those, only addresses ending 0xaa are
affected by this patch, by masking in the extra low bit when the device
is known to be in compatibility mode.
[dwmw2: Do it only when (cmd_ofs & 0xff) == 0xaa]
v4: Fix stupid typo in cfi_build_cmd_addr that failed to compile
I'm writing this patch way to late at night.
v3: Bring all of the work back into cfi_build_cmd_addr
including calling of map_bankwidth(map) and cfi_interleave(cfi)
So every caller doesn't need to.
v2: Only modified the address if we our device_type is larger than our
bus width.
Cc: stable@kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Finally move registration of sharpsl-nand device to board-specific code.
sharpsl nand driver is now clean and simple.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Merge mtd_info and nand_chip info special struct and
make it drvdata instead of plain static variable.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Start cleanup of sharpsl_nand driver. Convert it to platform driver.
Corresponding device is temprorary registered in sharpsl.c but will be
later moved to corresponding board files.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
replace open_bdev_excl/close_bdev_excl with variants taking fmode_t.
superblock gets the value used to mount it stored in sb->s_mode
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
To keep the size of changesets sane we split the switch by drivers;
to keep the damn thing bisectable we do the following:
1) rename the affected methods, add ones with correct
prototypes, make (few) callers handle both. That's this changeset.
2) for each driver convert to new methods. *ALL* drivers
are converted in this series.
3) kill the old (renamed) methods.
Note that it _is_ a flagday; all in-tree drivers are converted and by the
end of this series no trace of old methods remain. The only reason why
we do that this way is to keep the damn thing bisectable and allow per-driver
debugging if anything goes wrong.
New methods:
open(bdev, mode)
release(disk, mode)
ioctl(bdev, mode, cmd, arg) /* Called without BKL */
compat_ioctl(bdev, mode, cmd, arg)
locked_ioctl(bdev, mode, cmd, arg) /* Called with BKL, legacy */
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* git://git.infradead.org/mtd-2.6: (69 commits)
Revert "[MTD] m25p80.c code cleanup"
[MTD] [NAND] GPIO driver depends on ARM... for now.
[MTD] [NAND] sh_flctl: fix compile error
[MTD] [NOR] AT49BV6416 has swapped erase regions
[MTD] [NAND] GPIO NAND flash driver
[MTD] cmdlineparts documentation change - explain where mtd-id comes from
[MTD] cfi_cmdset_0002.c: Add Macronix CFI V1.0 TopBottom detection
[MTD] [NAND] Fix compilation warnings in drivers/mtd/nand/cs553x_nand.c
[JFFS2] Write buffer offset adjustment for NOR-ECC (Sibley) flash
[MTD] mtdoops: Fix a bug where block may not be erased
[MTD] mtdoops: Add a magic number to logged kernel oops
[MTD] mtdoops: Fix an off by one error
[JFFS2] Correct parameter names of jffs2_compress() in comments
[MTD] [NAND] sh_flctl: add support for Renesas SuperH FLCTL
[MTD] [NAND] Bug on atmel_nand HW ECC : OOB info not correctly written
[MTD] [MAPS] Remove unused variable after ROM API cleanup.
[MTD] m25p80.c extended jedec support (v2)
[MTD] remove unused mtd parameter in of_mtd_parse_partitions()
[MTD] [NAND] remove dead Kconfig associated with !CONFIG_PPC_MERGE
[MTD] [NAND] driver extension to support NAND on TQM85xx modules
...
This reverts commit 75d0ee2202.
Although it seems ObviouslyCorrect™, the spi_write() call uses DMA,
while spi_write_then_read() does not. Since our buffer is on the stack,
we must use the latter even though we don't actually want to read
anything back.
Pointed out by David Brownell <david-b@pacbell.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Not all architectures provide readsb(). We should probably move to using
ioread8_rep() instead.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix compile error because the first patch was broken -- the file got
truncated.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The CFI information read from AT49BV6416 lists the erase regions in the
wrong order, causing problems when trying to erase or update the first
or last 64KiB block.
Work around this by inverting the "top boot" flag, which will
effectively reverse the order of the erase regions.
This chip is obsolete, but it's used in some existing designs.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The patch adds support for NAND flashes connected to GPIOs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds TopBottom detection for most Macronix chips with CFI V1.0.
The main purpose of this patch is to add detection of the MX29LV400C B
used on the LaCie Ethernet Disk mini V2 NAS.
It detects the following parts correctly:-
MX28F640C3B T
MX29LV002C B
MX29LV002NC B
MX29LV004C T
MX29LV400C T/B
MX29LV800C T/B
MX29LV160C T/B
MX29SL800C T/B
MX29SL802C T/B
It detects the following uniform part as bottom but it should work
correctly:-
MX29LV040C
For T parts it causes the erase block table to be reversed correctly.
For other parts it avoids the bogus "Assuming top" message.
It does not detect the following correctly:-
MX28F640C3B B
MX29LV002C T
MX29LV002NC T
MX29LV004C B
MX29SL400C T/B
MX29SL402C T/B
If desired I could supply a more complicated patch to handle these as
well.
Only the MX29LV400C B has been physically tested; others were checked
against their data sheets.
Signed-off-by: Christopher Moore <moore@free.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This makes the driver erase a block when it doesn't find any
existing saved log messages which is safer than assuming the
flash was already erased.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a magic number to logged kernel oops messages so that they
can be more accurately detected rather than just having to rely
on the sequence number. This also allows easier detection of
saved crashes by userspace.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix an off by one error in the mtdoops driver
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits)
UIO: Fix mapping of logical and virtual memory
UIO: add automata sercos3 pci card support
UIO: Change driver name of uio_pdrv
UIO: Add alignment warnings for uio-mem
Driver core: add bus_sort_breadthfirst() function
NET: convert the phy_device file to use bus_find_device_by_name
kobject: Cleanup kobject_rename and !CONFIG_SYSFS
kobject: Fix kobject_rename and !CONFIG_SYSFS
sysfs: Make dir and name args to sysfs_notify() const
platform: add new device registration helper
sysfs: use ilookup5() instead of ilookup5_nowait()
PNP: create device attributes via default device attributes
Driver core: make bus_find_device_by_name() more robust
usb: turn dev_warn+WARN_ON combos into dev_WARN
debug: use dev_WARN() rather than WARN_ON() in device_pm_add()
debug: Introduce a dev_WARN() function
sysfs: fix deadlock
device model: Do a quickcheck for driver binding before doing an expensive check
Driver core: Fix cleanup in device_create_vargs().
Driver core: Clarify device cleanup.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
module: remove CONFIG_KMOD in comment after #endif
remove CONFIG_KMOD from fs
remove CONFIG_KMOD from drivers
Manually fix conflict due to include cleanups in drivers/md/md.c
This updates most of the OMAP drivers which are in mainline to switch to
using the cross-platform GPIO calls instead of the older OMAP-specific
ones.
This is all fairly brainless/obvious stuff. Probably the most interesting
bit is to observe that the omap-keypad code seems to now have a portable
core that could work with non-OMAP matrix keypads. (That would improve
with hardware IRQ debouncing enabled, of course...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Straight forward conversions to CONFIG_MODULE; many drivers
include <linux/kmod.h> conditionally and then don't have any
other conditional code so remove it from those.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: video4linux-list@redhat.com
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-ppp@vger.kernel.org
Cc: dm-devel@redhat.com
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Several Renesas SuperH CPU has FLCTL. The FLCTL support NAND Flash.
This driver support SH7723.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The functions that write the OOB info (on hardware ECC only) use the
HW_SYNDROME method.
This is not correct : the start position is "pos = eccsize + chunk" and
should be eccsize. So, the standard (nand_write_oob_std) function should
be used. This patch corrects this by using NAND_ECC_HW instead of
NAND_ECC_HW_SYNDROME.
This has only been tested on small pages nand flash.
(if anyone can test it on large pages that would be great).
kernel version : 2.6.27-rc2 (current git mtd-2.6)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
Removed the Kconfig associated with 'NDFC NanD Flash Controller'.
We can't enable !CONFIG_PPC_MERGE so there is no way to enable
this. Additionally the code needs to get updated for arch/powerpc.
For the time being lets just remove the Kconfig option so we can
actually remove CONFIG_PPC_MERGE.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch extends the FSL UPM NAND driver from Anton Vorontsov to
support hardware which does not have the R/B pin of the NAND chip
connected, like the TQM8548 module:
- The OF_GPIO dependency has been removed from the Kconfig option
because GPIO is not needed. The relevant gpio_* function are then
stubbed out in <linux/gpio.h>.
- It re-introduces the chip-delay property to define an appropriate
maximum delay time (tR) required for read operations. The binding
will be documented in a separate patch.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
- Get rid of fsl,wait-pattern and fsl,wait-write. I think this isn't
chip-specific, and we should always do waits. I saw one board that
didn't need fsl,wait-pattern, but I assume this was the exception
that proves the rule;
- Get rid of chip-delay. Today there are no users for this, and if
anyone really need this they should push the OF bindings beforehand;
- Now flash chips should be child nodes of the FSL UPM NAND controller;
- Implement OF partition parsing.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch makes debugging a missconfigured UBI a bit easier
by providing the needed information in the boot log.
Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
We can benefit from knowing that the file system no longer cares about
the contents of certain sectors, by throwing them away immediately and
then never having to garbage collect them, and using the extra free
space to make our operations more efficient. Do so.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When iterating over a chain in reverse (oldest block first), this
patch correctly marks the PUtable[] entry of the second to last erase
block of a chain as BLOCK_NIL, regardless of whether or not it can
format the last block successfully. Before, the second to last block
was only marked as pointing to BLOCK_NIL if INFTL_formatblock()
succeeded on the last block of the chain, which could potentially
result in an infinite loop if the block was worn out and refused to
format.
Signed-off-by: Daniel Rosenthal <danielrosenthal@acm.org>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
...since it only probes that
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Now that the needed helpers are exported, it becomes a nice simple
switch over. Closes#9420
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The patch fixes CFI issue with multipartitional devices leading to the
set of errors or even deadlock. The problem is CFI FL_SYNCING state race
with flash operations (e.g. erase suspend). It is reproduced by running
intensive writes on one JFFS2 partition and simultaneously performing
mount/unmount cycle on another partition of the same chip.
Signed-off-by: Alexander Belyakov <abelyako@googlemail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In case of error, the function add_volume returns an ERR pointer. The
result of IS_ERR, which is supposed to be used in a test as it is, is
here checked to be less than zero, which seems odd. We suggest to
replace this test by a simple IS_ERR test.
A simplified version of the semantic match that finds this problem is
as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@def0@
expression x;
position p0;
@@
x@p0 = add_volume(...)
@protected@
expression def0.x,E;
position def0.p0;
position p;
statement S;
@@
x@p0
... when != x = E
if (!IS_ERR(x) && ...) {<... x@p ...>} else S
@unprotected@
expression def0.x,E;
identifier fld;
position def0.p0;
position p != protected.p;
@@
x@p0
... when != x = E
* x@p->fld
// </smpl>
Signed-off-by: Julien Brunel <brunel@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Add copyright information for some of the AT91 header files.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some chips require a RESET after power-up (e.g. Micron MT29FxGxxxxx).
The first command sent is NAND_CMD_READID.
Issue a NAND_CMD_RESET in nand_scan_ident before reading the device id.
Tested with an MT29F4G08AAC.
Signed-off-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Very occasionally, (about one in a million) read operations are
ongoing after the timeout has expired. So, retry three times
while the ongoing bit remains set.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix offset of second word used for programming base address of memory
window. Also program tmio with offset of the FCR, not with physical
memory location.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for the integrated NAND flash controller of the
i.MX2 and i.MX3 family. It is tested on MX27 but should work on MX3
aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The MEMGETREGIONINFO ioctl() in mtdchar.c was clobbering user memory by
overwriting more than intended, due the size of struct mtd_erase_region_info
changing in commit 0ecbc81adf ('Support
for auto locking flash on power up').
Fix avoids this by copying struct members one by one with put_user(), as there
is no longer a convenient struct to use the size of as the length argument to
copy_to_user().
Signed-off-by: Zev Weiss <zevweiss@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Minor patch to help debugging of NAND detection.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch moves some attributes out from the platform data into the
dynamically created nand device. This results into a cleaner interface
and allows to use constant pxa3xx_nand_flash definitions.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch marks some attributes as 'const' which are set only once and
never be modified by the driver. There are some changes in parameter
list and variable declarations too which mark them as 'const'.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a MTD_NAND_PXA3xx_BUILTIN configuration variables which
allows to disable usage of builtin flash-type table. Not enabling this
option saves some space in the generated driver.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds 'flash' and 'num_flash' attributes to the platform data.
There was added code in the driver to iterate across these attributes in the
detect-flash routine. This is done similarly to the existing method
which uses a 'builtin_flash_types' field.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch moves the exported datastructures from the pxa3xx_nand.c driver
into the <mach/pxa3xx_nand.h> header. This is a plain movement without
any modification of the attributes.
This is the first one of a set of patches which:
* allows to specify used NAND flash in the platform code and allows to turn
off the old way to specify NAND characteristics in the driver. This way did
not worked well as these characteristics depend on the platform and can not be
derived from NAND id alone.
E.g. some NAND chips share the same ID (e.g. K9K8G08U0A and K9NBG08U5A) but
have different timings (which are written in the common driver currently and
must be modified there).
* adds 'const' annotations at various places
Further patches will be sent to the mtd-list.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Semun Lee <semun.lee@samsung.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since we're just parsing the tuple being passed to this function, we don't
need any device-specific information.
Also, remove the call to pcmcia_validate_cis() from pcmciamtd.c, since it
is already called by the PCMCIA core.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
It doesn't use LINUX_VERSION_CODE nor KERNEL_VERSION.
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of using own error or success codes, the PCMCIA code should rely on
the generic return values. Therefore, replace all occurrences of CS_SUCCESS
with 0.
CC: netdev@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Remove the three remaining pcmcia_get_configuration_info() users:
- pcmciamtd is marked broken anyway.
- serial_cs.c can access the relevant structs directly
- ipwireless didn't use the output
CC: linux-serial@vger.kernel.org
CC: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch for nand_ecc.c fixes three issues
- fix code so it also works on big endian architectures
- added a printk in case of an uncorrectable ecc error
- strengthen the test for correctable errors (decreasing the chance
that multiple bit faults by accident will be seen as correctable)
Note: the big endian code is only tested in a testbed (running on big endian
hardware) as I cannot rebuild and test a big endian kernel at the moment.
However the only thing that can go wrong is if <asm/byteorder.h> does not
give __BIG_ENDIAN in that case. In my eyes very unlikely.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/mtd/maps/amd76xrom.c
drivers/mtd/maps/ck804xrom.c
drivers/mtd/maps/esb2rom.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* master.kernel.org:/home/rmk/linux-2.6-arm: (38 commits)
[ARM] 5191/1: ARM: remove CVS keywords
[ARM] pxafb: fix the warning of incorrect lccr when lcd_conn is specified
[ARM] pxafb: add flag to specify output format on LDD pins when base is RGBT16
[ARM] pxafb: fix the incorrect configuration of GPIO77 as ACBIAS for TFT LCD
[ARM] 5198/1: PalmTX: PCMCIA fixes
[ARM] Fix a pile of broken watchdog drivers
[ARM] update mach-types
[ARM] 5196/1: fix inline asm constraints for preload
[ARM] 5194/1: update .gitignore
[ARM] add proc-macros.S include to proc-arm940 and proc-arm946
[ARM] 5192/1: ARM TLB: add v7wbi_{possible,always}_flags to {possible,always}_tlb_flags
[ARM] 5193/1: Wire up missing syscalls
[ARM] traps: don't call undef hook functions with spinlock held
[ARM] 5183/2: Provide Poodle LoCoMo GPIO names
[ARM] dma-mapping: provide sync_range APIs
[ARM] dma-mapping: improve type-safeness of DMA translations
[ARM] Kirkwood: instantiate the orion_spi driver in the platform code
[ARM] prevent crashing when too much RAM installed
[ARM] Kirkwood: Instantiate mv_xor driver
[ARM] Orion: Instantiate mv_xor driver for 5182
...
This patch improves the performance of the ecc generation code by a
factor of 18 on an INTEL D920 CPU, a factor of 7 on MIPS and a factor of 5
on ARM (NSLU2)
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
On OMAP3, the driver was occasionally not seeing the GPIO
interrupt. Adding a small delay of one register read
eliminates the problem.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver had resided in the OMAP tree but is now to be in MTD.
Original authors were:
Jarkko Lavinen <jarkko.lavinen@nokia.com> and Juha Yrjölä
IRQ and DMA support written by Timo Teras
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
- add extended device information support
- add s25sl128 device support
Signed-off-by: Chen Gong <g.chen@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds an erase_block command to enhance erase operation
Signed-off-by: Chen Gong <g.chen@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Removed duplicated include <asm/div64.h> in
drivers/mtd/nand/nandsim.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The TMIO chips are only found (and thus tested) on ARM machines.
Moreover, we don't want the TMIO cells to be built if one of the TMIO
driver is not selected (which indirectly make the TMIO cells drivers
depend on ARM as well).
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch adds support for the NAND controller commonly found in
TMIO based MFDs.
Signed-off-by: Ian Molton <spyro@f2s.com>
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch performs the equivalent include directory shuffle for
plat-orion, and fixes up all users.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
They need to be exported, so let's give them less generic-sounding names
while we're at it.
Original export patch, along with the suggestion about the nomenclature,
from Stephen Rothwell.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This adds a WRITE_VERIFY Kconfig option to the DataFlash driver,
closely mirroring the similar NAND and ONENAND options, giving
an option to disable some code that's currently always enabled.
Removing this step probably saves a millisecond or so per page
when writing data, which will add up quickly since these pages
are small (the largest is 1 KiB). It doesn't seem to add a
lot in terms of reliability, and wouldn't detect errors which
crop up when transferring data to the on-chip SRAM buffer.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
> > linux-next-20080805/drivers/mtd/devices/mtd_dataflash.c: In function 'add_dataflash_otp':
> > linux-next-20080805/drivers/mtd/devices/mtd_dataflash.c:670: error: too many arguments to function 'otp_setup'
Whoops, sorry ... I see what was going on. My bad.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Timeouts are currently given by the typical operation time times 8.
It works in the general well-behaved case but not when an erase block is
failing. For erase operations, it seems that a failing erase block will
keep the device state machine in erasing state until the vendor
specified maximum timeout period has passed. By this time the driver
would have long since timed out, left erasing state and attempted
further operations which all fail. This patch implements timeouts using
values from the CFI Query structure when available.
The patch also sets a longer timeout for locking operations. The current
value used for locking/unlocking given by 1000000/HZ microseconds is too
short for devices like J3 and J5 Strataflash which have a typical clear
lock-bits time of 0.5 seconds.
Signed-off-by: Anders Grafström <grfstrm@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There are some CFI chips which require non standard procedures to get
into QRY mode. The possible way to support them would be trying
different modes till QRY will be read. This patch introduce two new
functions qry_mode_on qry_mode_off. qry_mode_on tries different commands
in order switch chip into QRY mode.
So if we have one more "odd" chip - we just could add several lines to
qry_mode_on. Also using these functions remove unnecessary code
duplicaton in porbe procedure.
Currently there are two "odd" cases
1. Some old intel chips which require 0xFF before 0x98
2. ST M29DW chip which requires 0x98 to be sent at 0x555 (according to
CFI should be 0x55)
This patch is partialy based on the patch from Uwe
(see "[PATCH 2/4] [RFC][MTD] cfi_probe: remove Intel chip workaround"
thread )
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Signed-off-by: Alexander Belyakov <abelyako@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This long overdue trivial change to the MTD_CFI_AMDSTD kconfig menu
description is intended to help clarify that this option also supports
Spansion flash devices.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This was a reference board for which support never got merged upstream.
Kill it off, at rmk's suggestion.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
No file should be explicitly referencing its own platform headers
by specifying an absolute include path. Fix these paths to use
standard <asm/arch/...> includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As reported by Adrian Bunk, commit d5686b444f
(switch mtd and dm-table to lookup_bdev()) causes the following compile
error with CONFIG_BLOCK=n:
CC drivers/mtd/mtdsuper.o
drivers/mtd/mtdsuper.c: In function `get_sb_mtd':
drivers/mtd/mtdsuper.c:184: error: implicit declaration of function 'lookup_bdev'
drivers/mtd/mtdsuper.c:184: warning: assignment makes pointer from integer without a cast
drivers/mtd/mtdsuper.c:197: error: implicit declaration of function 'bdput'
make[3]: *** [drivers/mtd/mtdsuper.o] Error 1
Fix it by putting the block device lookup inside #ifdef CONFIG_BLOCK
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore
remove the dead code associated with !CONFIG_PPC_MERGE.
The mtd maps should be using the OF based mechanism.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Now that we can tell when we have one of the newer DataFlash chips,
optionally expose the 128 bytes of OTP memory they provide. Tested
on at45db642 revision B and D chips.
Switch mtdchar over to a generic HAVE_MTD_OTP flag instead of adding
another #ifdef for each type of chip whose driver has OTP support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6:
[MTD] [NAND] drivers/mtd/nand/nandsim.c: fix printk warnings
[MTD] [NAND] Blackfin NFC Driver: Cleanup the error exit path of bf5xx_nand_probe function
[MTD] [NAND] Blackfin NFC Driver: use standard dev_err() rather than printk()
[MTD] [NAND] Blackfin NFC Driver: enable Blackfin nand HWECC support by default
[MTD] [NAND] Blackfin NFC Driver: add proper devinit/devexit markings to probe/remove functions
[MTD] [NAND] Blackfin NFC Driver: add support for the ECC layout the Blackfin bootrom uses
[MTD] [NAND] Blackfin NFC Driver: fix bug - hw ecc calc by making sure we extract 11 bits from each register instead of 10
[MTD] [NAND] Blackfin NFC Driver: fix bug - do not clobber the status from the first 256 bytes if operating on 512 pages
[MTD] [NAND] diskonchip.c fix sparse endian warnings
[MTD] [NAND] drivers/mtd/nand/nandsim.c needs div64.h
[JFFS2] Fix allocation of summary buffer
Fix rename of at91_nand -> atmel_nand
[MTD] [NOR] drivers/mtd/chips/jedec_probe.c: fix Am29DL800BB device ID
[MTD] MTD_DEBUG always does compile-time typechecks
[MTD] DataFlash: bugfix, binary page sizes now handled
[MTD] [NAND] fsl_elbc_nand.c: fix printk warning
[MTD] [NAND] nandsim: support random page read command
[MTD] [NAND] fix subpage read for small page NAND
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
drivers/mtd/nand/nandsim.c: In function 'divide':
drivers/mtd/nand/nandsim.c:462: error: implicit declaration of function 'do_div'
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The device id for Am29DL800BB in jedec_probe.c is wrong.
Reference: http://www.spansion.com/datasheets/21519c4.pdf
I discovered this while working with u-boot.
The u-boot folks mentioned Linux as an upstream reference, thought I'd
post a heads-up here too.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The wrong version of the "teach dataflash about binary density" patch
just got merged (v2 not v3) ... this restores the missing updates:
* Fix the cmdlinepart *regression* that caused testing failures (!!)
by restoring the original part labels in relevant cases.
* Don't reference things that don't exist (!)
- An opcode that doesn't even exist for DataFlash
- The part is "at45db642" not "at45db641"
- ID zero in this JEDEC table
* Make the JEDEC probe routine report and handle errors better:
- If the SPI calls fail, return the error codes.
- Don't depend on ordering of table entries.
- Unrecognized ids are different from parts that have no ID.
We won't actually know how to handle them correctly; display
the ID and ignore the chip.
* Move the original block comment about the "legacy" chip ID scheme
back next to the code to which it applies ... not next to the new
JEDEC query code, which uses an entirely different strategy.
* Don't print a guessed erasesize; /proc/mtd has the real value.
And add a few more comments.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
drivers/mtd/nand/fsl_elbc_nand.c:890: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit 3d45955962 ("subpage read feature
as a way to improve performance") broke nandsim because nandsim does not
support the "random page read" NAND command. This patch adds
corresponding support.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (57 commits)
[MTD] [NAND] subpage read feature as a way to increase performance.
CPUFREQ: S3C24XX NAND driver frequency scaling support.
[MTD][NAND] au1550nd: remove unused variable
[MTD] jedec_probe: Fix SST 16-bit chip detection
[MTD][MTDPART] Fix a division by zero bug
[MTD][MTDPART] Cleanup and document the erase region handling
[MTD][MTDPART] Handle most checkpatch findings
[MTD][MTDPART] Seperate main loop from per-partition code in add_mtd_partition
[MTD] physmap: resume already suspended chips on failure to suspend
[MTD] physmap: Fix suspend/resume/shutdown bugs.
[MTD] [NOR] Fix -ETIMEO errors in CFI driver
[MTD] [NAND] fsl_elbc_nand: fix section mismatch with CONFIG_MTD_OF_PARTS=y
[JFFS2] Use .unlocked_ioctl
[MTD] Fix const assignment in the MTD command line partitioning driver
[MTD] [NOR] gen_probe: No debug message when debugging is disabled
[MTD] [NAND] remove __PPC__ hardcoded address from DiskOnChip drivers
[MTD] [MAPS] Remove the bast-flash driver.
[MTD] [NAND] fsl_elbc_nand: ecclayout cleanups
[MTD] [NAND] fsl_elbc_nand: implement support for flash-based BBT
[MTD] [NAND] fsl_elbc_nand: fix OOB workability for large page NAND chips
...
This patch enables NAND subpage read functionality.
If upper layer drivers are requesting to read non page aligned data NAND
subpage-read functionality reads the only whose ECC regions which include
requested data when original code reads whole page.
This significantly improves performance in many cases.
Here are some digits :
UBI volume mount time
No subpage reads: 5.75 seconds
Subpage read patch: 2.42 seconds
Open/stat time for files on JFFS2 volume:
No subpage read 0m 5.36s
Subpage read 0m 2.88s
Signed-off-by Alexey Korolev <akorolev@infradead.org>
Acked-by: Artem Bityutskiy <dedekind@infradead.org>
Acked-by: Jörn Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for CPU frequency scalling to the S3C24XX NAND driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The unlock_addr rework in kernel 2.6.25 breaks 16-bit SST chips. SST
39LF160 and SST 39VF1601 are both 16-bit only chip (do not have BYTE#
pin) and new uaddr value is not correct for them. Add
MTD_UADDR_0xAAAA_0x5555 for those chips. Tested with SST 39VF1601
chip.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When detecting a partition beyond the end of the device, skip most of
the initialisation, in particular those bits causing a division by zero.
Signed-off-by: Jörn Engel <joern@logfs.org>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mostly simplifying the loops. Now everything fits into 80 columns,
is easier to read and the finer details have extra comments.
Signed-off-by: Jörn Engel <joern@logfs.org>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remaining are 12 warnings about long lines and 1 about braces that
could be argued about.
Signed-off-by: Jörn Engel <joern@logfs.org>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
add_mtd_partition was a 150+ line monster consisting mostly of a single
loop. Seperate the loop from most of the body. Now it should be
obvious which variables are carried around from iteration to iteration.
Signed-off-by: Jörn Engel <joern@logfs.org>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
A nice side effect of this patch is that the return value of
physmap_flash_suspend in the error path is the value of the first failing
suspend callback and not the bitwise OR of all of them.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Don't call suspend/resume functions if they have not been
defined.
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Acked-By: Jörn Engel <joern@logfs.org>
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Existing CFI driver has problems with excessive writes during erase.
If CFI driver does many writes during one erase cycle we may face the
messages with -ETIMEO error on erase operation. It may cause the
following data corruption and kernel panics.
The reason of the issue is related to specifics of suspend operation:
if we write to flash during erase, suspend operation will cost some time
to erase procedure (for P30 it could be significant). In current version of
cfi driver the problem of many suspends is partially workarounded by adding
some time reserv to any operation (8xerase_time) but if we have many writes
during one erase the problem appears.
This patch detects the suspend and resets timer if suspend occured. It
has been well verified on different chips. No problems were found.
Could you please include the patch as it is simple and fixes bad issue.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
With CONFIG_MTD_OF_PARTS=y I'm getting this new section mismatch in reference
from the function fsl_elbc_chip_probe() to the function
.devinit.text:of_mtd_parse_partitions()
This patch fixes the mismatch by providing __devinit annotation to the
fsl_elbc_chip_probe() function.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fix only affects UBI debugging.
If the the background thread is disabled for debugging purposes,
start it anyway, because otherwise we see tonns of kernel debugging
complaints like this:
INFO: task ubi_bgt0d:26857 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
ubi_bgt0d D dd37bf94 0 26857 2
dd37bfcc 00000086 f8e17cea dd37bf94 00000046 00000000 00000000 f5c62430
f5c62430 f5c62590 c2a09c80 f6cbd498 dd8e9cbc 00000296 dd37bfb0 00000296
dd8e9cb8 dd8e9cbc dd37bfcc c0119774 00000000 00000000 c0132e89 f6961560
Call Trace:
[<f8e17cea>] ? ubi_thread+0x0/0x127 [ubi]
[<c0119774>] ? complete+0x43/0x4b
[<c0132e89>] ? kthread+0x0/0x5b
[<f8e17cea>] ? ubi_thread+0x0/0x127 [ubi]
[<c0132eae>] kthread+0x25/0x5b
[<c0132e89>] ? kthread+0x0/0x5b
[<c0104953>] kernel_thread_helper+0x7/0x14
=======================
So start it, and go sleep inside it, instead of creating it and never
start.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
On 32-bit architectures PAGE_ALIGN() truncates 64-bit values to the 32-bit
boundary. For example:
u64 val = PAGE_ALIGN(size);
always returns a value < 4GB even if size is greater than 4GB.
The problem resides in PAGE_MASK definition (from include/asm-x86/page.h for
example):
#define PAGE_SHIFT 12
#define PAGE_SIZE (_AC(1,UL) << PAGE_SHIFT)
#define PAGE_MASK (~(PAGE_SIZE-1))
...
#define PAGE_ALIGN(addr) (((addr)+PAGE_SIZE-1)&PAGE_MASK)
The "~" is performed on a 32-bit value, so everything in "and" with
PAGE_MASK greater than 4GB will be truncated to the 32-bit boundary.
Using the ALIGN() macro seems to be the right way, because it uses
typeof(addr) for the mask.
Also move the PAGE_ALIGN() definitions out of include/asm-*/page.h in
include/linux/mm.h.
See also lkml discussion: http://lkml.org/lkml/2008/6/11/237
[akpm@linux-foundation.org: fix drivers/media/video/uvc/uvc_queue.c]
[akpm@linux-foundation.org: fix v850]
[akpm@linux-foundation.org: fix powerpc]
[akpm@linux-foundation.org: fix arm]
[akpm@linux-foundation.org: fix mips]
[akpm@linux-foundation.org: fix drivers/media/video/pvrusb2/pvrusb2-dvb.c]
[akpm@linux-foundation.org: fix drivers/mtd/maps/uclinux.c]
[akpm@linux-foundation.org: fix powerpc]
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following warning:
drivers/mtd/ubi/vmt.c: In function 'ubi_rename_volumes':
drivers/mtd/ubi/vmt.c:642: warning: statement with no effect
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Before UBI got into mainline, there was a slight flash format
change - we did not have sequence number support, then added it.
We have carried full support of those ancient images till this
moment. Now the support is removed, well, not fully removed.
Now UBI will support only _clean_ old images, which were cleanly
detached last time (just before kernel upgrade). This is most
likely the case.
But we will not support unclean ancient images. Surprisingly,
this allows us to remove a big chunk of legacy code.
And the same should be true for downgrading: clean images should
downgrade fine, but unclean ones will not.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
No functional changes, just tweak comments to make kernel-doc
work fine and stop complaining.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Just out or curiousity ran checkpatch.pl for whole UBI,
and discovered there are quite a few of stylistic issues.
Fix them.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This is probably a copy-paste bug - we torture the old PEB
in the atomic LEB change function, but we should not do this.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
If bit-flips happen often, UBI prints to many messages. Lessen
the amount by only printing the messages when the PEB has been
scrubbed. Also, print torturing messages.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Quite useful ioctl which allows to make atomic system upgrades.
The idea belongs to Richard Titmuss <richard_titmuss@logitech.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Hch asked not to use "unit" for sub-systems, let it be so.
Also some other commentaries modifications.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Check that volume name is not shorter than 'name_len'.
No need to copy the trailing zero byte because whole array
was zeroed earlier.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
leb_read_unlock() may be called simultaniously by several tasks.
The would race at the following code:
up_read(&le->mutex);
if (free)
kfree(le);
And it is possible that one task frees 'le' before the other tasks
do 'up_read()'. Fix this by doing up_read and free inside the
'ubi->ltree' lock. Below it the oops we had because of this:
BUG: spinlock bad magic on CPU#0, integck/7504
BUG: unable to handle kernel paging request at 6b6b6c4f
IP: [<c0211221>] spin_bug+0x5c/0xdb
*pde = 00000000 Oops: 0000 [#1] PREEMPT SMP Modules linked in: ubifs ubi nandsim nand nand_ids nand_ecc video output
Pid: 7504, comm: integck Not tainted (2.6.26-rc3ubifs26 #8)
EIP: 0060:[<c0211221>] EFLAGS: 00010002 CPU: 0
EIP is at spin_bug+0x5c/0xdb
EAX: 00000032 EBX: 6b6b6b6b ECX: 6b6b6b6b EDX: f7f7ce30
ESI: f76491dc EDI: c044f51f EBP: e8a736cc ESP: e8a736a8
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process integck (pid: 7504, ti=e8a72000 task=f7f7ce30 task.ti=e8a72000)
Stack: c044f754 c044f51f 00000000 f7f7d024 00001d50 00000001 f76491dc 00000296 f6df50e0 e8a736d8 c02112f0 f76491dc e8a736e8 c039157a f7d9e830 f76491d8 e8a7370c c020b975 f76491dc 00000296 f76491f8 00000000 f76491d8 00000000 Call Trace:
[<c02112f0>] ? _raw_spin_unlock+0x50/0x7c
[<c039157a>] ? _spin_unlock_irqrestore+0x20/0x58
[<c020b975>] ? rwsem_wake+0x4b/0x122
[<c0390e0a>] ? call_rwsem_wake+0xa/0xc
[<c0139ee7>] ? up_read+0x28/0x31
[<f8873b3c>] ? leb_read_unlock+0x73/0x7b [ubi]
[<f88742a3>] ? ubi_eba_read_leb+0x195/0x2b0 [ubi]
[<f8872a04>] ? ubi_leb_read+0xaf/0xf8 [ubi]
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Normally UBI volumes are freed in the release function of
the struct device object. However, on error path they may
have to be freed before the struct device objects have been
initialized.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
UBI forgets to free internal volumes when detaching MTD device.
Fix this.
Pointed-out-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
ubi_free_volume() function sets ubi->volumes[] to NULL, so
ubi_eba_close() is useless, it does not free what has to be freed.
So zap it and free vol->eba_tbl at the volume release function.
Pointed-out-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
UBI already checks that @min io size is the power of 2 at io_init.
It is save to use bit operations then.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Instead of correctly pad the buffer wich we are writing to the
eraseblock during update, we used weird construct:
memset(buf + len, 0xFF, len - len);
Fix this.
Signed-off-by: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
It is not clear why we schedule PEB for scrubbing in case of
-EBADMSG. Elaborate.
Requested-by: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (85 commits)
[ARM] pxa: add base support for PXA930 Handheld Platform (aka SAAR)
[ARM] pxa: add base support for PXA930 Evaluation Board (aka TavorEVB)
[ARM] pxa: add base support for PXA930 (aka Tavor-P)
[ARM] Update mach-types
[ARM] pxa: make littleton to use the new smc91x platform data
[ARM] pxa: make zylonite to use the new smc91x platform data
[ARM] pxa: make mainstone to use the new smc91x platform data
[ARM] pxa: make lubbock to use new smc91x platform data
[NET] smc91x: prepare SMC_USE_PXA_DMA to be specified in platform data
[NET] smc91x: prepare for SMC_IO_SHIFT to be a platform configurable variable
[NET] smc91x: add SMC91X_NOWAIT flag to platform data
[NET] smc91x: favor the use of SMC91X_USE_* instead of SMC_CAN_USE_*
[NET] smc91x: remove "irq_flags" from "struct smc91x_platdata"
[ARM] 5146/1: pxa2xx: convert all boards to call pxa2xx_transceiver_mode helper
Support for LCD on e740 e750 e400 and e800 e-series PDAs
E-series UDC support
PXA UDC - allow use of inverted GPIO for pullup
Add e350 support
Fix broken e-series build
E-series GPIO / IRQ definitions.
...
This changes the MTD core to handle pci_name() now returning a constant
string.
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
[ARM] 5171/1: ep93xx: fix compilation of modules using clocks
[ARM] 5133/2: at91sam9g20 defconfig file
[ARM] 5130/4: Support for the at91sam9g20
[ARM] 5160/1: IOP3XX: gpio/gpiolib support
[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
[ARM] 5084/1: zylonite: Register AC97 device
[ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
[ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
[ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
[ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
[ARM] 5144/1: pxaficp_ir: cleanup includes
[ARM] pxa: remove pxa_set_cken()
[ARM] pxa: allow clk aliases
[ARM] Feroceon: don't disable BPU on boot
[ARM] Orion: LED support for HP mv2120
[ARM] Orion: add RD88F5181L-FXO support
[ARM] Orion: add RD88F5181L-GE support
[ARM] Orion: add Netgear WNR854T support
[ARM] s3c2410_defconfig: update for current build
[ARM] Acer n30: Minor style and indentation fixes.
...
Fix const to non-const pointer assignment in the MTD command line partitioning
driver.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use pr_debug(...) instead of printk(KERN_DEBUG ...) so that the message
is only printed when debugging is enabled.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: John stoffel <john@stoffel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Such a hardcoded address can cause a checkstop or machine check if
the driver is in the kernel but the address is not acknowledged.
Both drivers allow an address to be specified as either a module
parameter or config option. Any future powerpc board should either
use one of these methods or find the address in the device tree.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove the Simtec BAST flash driver as this has been replaced by using
the platform flash driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch deletes oobavail assignments, they're calculated by the nand
core code in nand_scan_tail, plus current oobavail values are wrong for
the LP NANDs.
Also remove mtd->ecclayout and mtd->oobavail assignments, mtd core
handles this all by itself.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch implements support for flash-based BBT for chips working
through ELBC NAND controller, so that NAND core will not have to re-scan
for bad blocks on every boot.
Because ELBC controller may provide HW-generated ECCs we should adjust
bbt pattern and bbt version positions in the OOB free area.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
For large page chips, nand_bbt is looking into OOB area, and checking
for "0xff 0xff" pattern at OOB offset 0. That is, two bytes should be
reserved for bbt means.
But ELBC driver is specifying ecclayout so that oobfree area starts at
offset 1, so only one byte left for the bbt purposes.
This causes problems with any OOB users, namely JFFS2: after first mount
JFFS2 will fill all OOBs with "erased marker", so OOBs will contain:
OOB Data: ff 19 85 20 03 00 ff ff ff 00 00 08 ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
And on the next boot, NAND core will rescan for bad blocks, then will
see "0xff 0x19" pattern, and will mark all blocks as bad ones.
To fix the issue we should implement our own bad block pattern: just one
byte at OOB start. Though, this will work only for x8 chips. For x16
chips two bytes must be checked. Since ELBC driver does not support x16
NANDs (yet), we're safe for now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There's no reason to prevent the Atmel NAND driver from
building as a module.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The ALE signal isn't correctly wired up to the ECC controller on the
AP7000, so it starts calculating ECC during the address cycles.
Work around this by resetting the ECC controller between the address and
data cycles.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This uses __raw_{read,write}s{b,w}() primitives to access data on NAND
chips for more efficient I/O.
On an arm926 with memory clocked at 100 MHz, this reduced the elapsed time
for a 64 MiB read by 16%. ("dd" /dev/mtd0 to /dev/null, with an 8-bit
NAND using hardware ECC and 128KiB blocksize.)
Also some minor section tweaks:
- Use platform_driver_probe() so no pointer to probe() lingers
after that code has been removed at run-time.
- Use __exit and __exit_p so the remove() code will normally be
removed by the linker.
Since these buffer read/write calls are new, this increases the runtime
code footprint (by 88 bytes on my build, after the section tweaks).
[haavard.skinnemoen@atmel.com: rebase onto atmel_nand rename]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use einfo, oinfo for the inner erase_info and otp_info structs used in
individual case statements.
drivers/mtd/mtdchar.c:582:26: warning: symbol 'info' shadows an earlier one
drivers/mtd/mtdchar.c:380:23: originally declared here
drivers/mtd/mtdchar.c:596:26: warning: symbol 'info' shadows an earlier one
drivers/mtd/mtdchar.c:380:23: originally declared here
drivers/mtd/mtdchar.c:704:19: warning: symbol 'info' shadows an earlier one
drivers/mtd/mtdchar.c:380:23: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The copy_to_user was casting away the address space to get the offset of
the length member. Use offsetof() instead and add it to the void __user
*argp.
drivers/mtd/mtdchar.c:527:23: warning: cast removes address space of expression
drivers/mtd/mtdchar.c:527:23: warning: incorrect type in argument 1 (different address spaces)
drivers/mtd/mtdchar.c:527:23: expected void [noderef] <asn:1>*to
drivers/mtd/mtdchar.c:527:23: got unsigned int *<noident>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Atmel serial flash tends to power up with the protection status bits set.
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=4089
[michael.hennerich@analog.com: remove duplicate code]
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Update CM-X270 NAND flash driver to use gpio_lib.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change omap_cf.c and omap_nor.c to use omap_readw/writew instead of __REG.
This is needed for multi-omap in the future.
Cc: David Brownell <david-b@pacbell.net>
Cc: linux-pcmcia@lists.infradead.org
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Tony Lindren <tony@atomide.com>
Some SoCs need a different chip_delay value.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Jörn Engel <joern@logfs.org>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Except for one debug message in a driver marked BROKEN, pcmcia_get_status is
only used by the ioctl. Therefore, move it to pcmcia_ioctl.c and unexport it.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The code in include/pcmcia/bulkmem.h was only kept for compatibility reasons.
Therefore, move the remaining region_info_t definition to ds.h
[linux@dominikbrodowski.net: do not modify the IOCTL, move definition to
ds.h, and update changelog]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As cisinfo_t only contains one unsigned_int, pccard_validate_cis can
be simplified by passing that around directly.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Make the atmel_nand driver selectable on AVR32, and update the Kconfig
help text to reflect this.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This fixes several bugs in the atmel_nand_probe() error path, including
at least one memory leak.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is basically s/at91_nand/atmel_nand/g with some manual inspection.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The AT91 NAND driver needs just a few tiny modifications to work on
AVR32 as well. Rename it atmel_nand to reflect this.
Also move the ECC register definitions into drivers/mtd/nand since they
are only useful to the atmel_nand driver, and get rid of the useless
filename at the top of each file.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
No point in using an AT91-specific GPIO API when the generic API works
just as well.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
WARNING: drivers/mtd/nand/built-in.o(.devinit.text+0x114): Section mismatch
in reference from the function fsl_elbc_ctrl_probe() to the function
.devexit.text:fsl_elbc_ctrl_remove()
__devinit functions should not call functions with __devexit. Since probe
function calls remove in case of errors, we want to remove __devexit
attribute from it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Although if people have questions about ARCnet, perhaps it's _better_
for them to be mailing dwmw2@cam.ac.uk about it...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix nandsim build error, missing #include:
linux-next-20080605/drivers/mtd/nand/nandsim.c: In function 'divide':
linux-next-20080605/drivers/mtd/nand/nandsim.c:462: error: implicit declaration of function 'do_div'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Now it returns the 0 if cmdlineparse not supplied.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The changelog on the driver is superflous given this
is being kept under revision control. Remove the other
cruft in the header and update the copyright and the
supported device list.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix a minor problem with what should have been
debug output by changing printk() to dev_dbg()
inside s3c2410_nand_update_chip().
Thanks to David Woodhouse for pointing this out.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Handle the case where flash memory and ethernet mac/phy are mapped onto
the same async bank
[try #4]
- drop superfluous casts
- drop SSYNC() when reading from the flash and rewrite
bfin_copy_from() to be like bfin_copy_to() so that
we dont have to handle all the aligned/unaligned cases
[try #3] rename bf5xx-flash to bfin-async-flash
- move all kconfig board settings into board resources
- fixup casting style according to lkml feedback
- rewrite driver so that it can handle arbitrary of
instances according to the declared platform resources
[try #2]
Remove useless SSYNC() as Will said
[try #1]
The BF533-STAMP does this for example.
All board-specific configuration goes in your board resources file.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Acked-By: Jörn Engel <joern@logfs.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Janitorial work to remove temporary pointers and make some functions a bit
more readable.
Signed-off-by: Chris Malley <mail@chrismalley.co.uk>
Reviewed-By: Jörn Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Once upon a time, the MTD repository was using CVS.
This patch therefore removes all usages of the no longer updated CVS
keywords from the MTD code.
This also includes code that printed them to the user.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Amend nandsim so that it does not assume 32-bit flash size.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
To get the correct information in case of power off recovery,
it should read ECC status first
Also remove previous workaround method.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
- Add support for binary page size DataFlashes.
- The driver now prints out pagesize and erasesize.
Printout valuable information for creating flash filesystems.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch add support for non-CFI Eon EN29SL800B[BT] NOR flash chips.
The Eon chips have manufacturer ID in the first bank, therefore this patch
depends on support for flash chips with ID in bank other than 0.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
According to JEDEC "Standard Manufacturer's Identification Code"
(http://www.jedec.org/download/search/jep106W.pdf)
several first banks of NOR flash can contain 0x7f instead of actual ID.
This patch adds support for reading manufacturer ID from banks other than 0.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
There's a reason why using C99 initialisers even in the supposedly
trivial structs is a good idea.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for M50FLW080A and M50FLW080B revisions of LPC flash
devices.
Signed-off-by: Aaron Lindner <alindner@xes-inc.com>
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
SH_MPC1211 has been marked as BROKEN for some time.
Unless someone is working on reviving it now, I'd therefore suggest this
patch to remove it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix typo in erase suspend while write fixup code leading to compile time
error if CMDSET0001_DISABLE_ERASE_SUSPEND_ON_WRITE was defined.
drivers/mtd/chips/cfi_cmdset_0001.c: In function 'fixup_intel_strataflash':
drivers/mtd/chips/cfi_cmdset_0001.c:212: error: 'struct cfi_pri_amdstd' has no member named 'SuspendCmdSupport'
Signed-off-by: Alexander Belyakov <abelyako@googlemail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Adding the ability to get a physical address from point() in addition
to virtual address. This physical address is required for XIP of
userspace code from flash.
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Reviewed-by: Jörn Engel <joern@logfs.org>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use at91_nand_enable(), at91_nand_disable() to manipulate enable_pin.
No functional changes.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This driver did not control NCE signal during normal operations (only
enable NCE on probing and disable NCE on removing). This patch make
NCE signal inactive on idle state.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The sam926x docs allegedly don't list an "ECC_PARITY" field, and the
header files in the upstream kernel don't have it either.
Masking with it was useless anyway, so just remove it.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is a patch to use the hardware ECC controller of
the AT91SAM9260 and AT91SAM9263 for the AT91 nand.
On AT91 NAND, there's now a choice between ECC soft,
ECC hard or no ECC (for debug).
It has been tested on AT91SAM9263 with 8 bits large
and small page NAND.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
UBI scan takes quite a time on some systems, so it is nice
to print a message that we started attaching an MTD device.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/ar7part.c: In function ‘create_mtd_partitions’:
drivers/mtd/ar7part.c:69: warning: passing argument 4 of ‘master->read’ from incompatible pointer type
drivers/mtd/ar7part.c:91: warning: passing argument 4 of ‘master->read’ from incompatible pointer type
drivers/mtd/ar7part.c:99: warning: passing argument 4 of ‘master->read’ from incompatible pointer type
drivers/mtd/ar7part.c:110: warning: passing argument 4 of ‘master->read’ from incompatible pointer type
drivers/mtd/ar7part.c:111: error: ‘SQUASHFS_MAGIC’ undeclared (first use in this function)
drivers/mtd/ar7part.c:111: error: (Each undeclared identifier is reported only once
drivers/mtd/ar7part.c:111: error: for each function it appears in.)
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
collie seems to contain LH28F640BF flash chips. According to
http://sharp-world.com/products/device/flash/pdf/*FUM00701*@E.pdf
(page 83) if they have 0x51 of Extended Query Table (number of hardware
partitions) set to zero, they have a single fixed partition.
This patch makes those chips work.
Signed-off-by: Thomas Kunze <thommycheck@gmx.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
With modern systems using bus-hold instead of bus pull-up, it can
often lead to erroneous reporting of NAND devices where there are
none. Do a double probe to ensure that the result we got the first
time is repeatable, and if it is not then return that there is no
chip there.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support to disable ECC checking for a given chip
when passed by the board via the platform data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for the ECC layout to be passed via the
platform data specified by the board.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
If a block's ecc field is all 0xff, then ignore the ECC
correction. This is for systems where some of the blocks,
such as the initial cramfs are written without ECC and
need to be loaded on start.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This adds support for using large page NAND devices
with the S3C24XX NAND controller. This also adds the
file Documentation/arm/Samsung-S3C24XX/NAND.txt to
describe the differences.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Commit 03680b1e00 incorrectly
was assuming S3C2410_NFCONF was being used to select the
NAND chip. Fix this error by ising the sel_reg.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
A power loss while writing can result in a page becoming unreadable.
When the device is mounted again, reading that page gives controller
errors. Upper level software like JFFS2 treat -EIO as fatal, refusing to
mount at all. That means it is necessary to treat the error as an ECC
error to allow recovery. Note that typically in this case, the
eraseblock can still be erased and rewritten i.e. it has not become a
bad block.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Minor tweaks to omap_nor ... as with most platform drivers, its probe
and remove logic can (and should!) safely vanish in most configs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is a known erratum confirmed by Spansion. I have an errata document,
but I can't find a link to it anywhere on their site to include here.
Some of the S29GL064N chips report 64 sectors when they should report 128,
and some of S29GL032N chips report 127 sectors when they should report 63.
Note that when the chip dies are fixed by Spansion, they will still have
the same id. The fix is done in such a way that it won't affect corrected
chips.
The fixups use the extended id made available by a previous patch. Without
that, virtually all newer AMD/Spansion chips will have the same ID (0x227e)
and it's not possible to apply the fixup to the correct chips.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
AMD/Spansion use a device id of 0x7e to indicate an extended device is
present at offset 0xe and 0xf in the query data.
I've verified with Spansion that all their chips (mfr == 0x01) with an id
of 0x7e use it to indicate an extended id is present. What's more, there
are no chips with a NON-extended id that is the same as a different chip's
extended id. In other words, when the extended ID is present, one can
replace the normal id with the extended id without losing any information.
Which is what I've done.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Using current driver elbc sometimes hangs during nand write. Reading back
last byte helps though (thanks to Scott Wood for the idea).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch sets mtd->name to the platform bus ID in the plat_nand
driver, so that you can specify partitions readily with mtdparts=.
Currently it relies on nand_base filling in the name from the device,
which results in names like "NAND 256MiB 3,3V 8-bit", that you can't
use with cmdlineparts.
Signed-off-by: Hamish Moffatt <hamish@cloud.net.au>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix a race condition in fsl_elbc_run_command
Fix incorrect usage of clearbits32 that bashed option register
Remove work around for bashed register
Signed-off-by: Mike Hench <mhench@elutions.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Currently fsl_elbc_nand doesn't initialize mtd->name, and this causes
nand_get_flash_type() to assign name that is equal to chip type, like
this:
root@b1:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00800000 00010000 "fe000000.flash"
mtd1: 02000000 00004000 "NAND 32MiB 3,3V 8-bit"
mtd0 is physmap_of flash (normal name), and mtd1 is fsl_elbc_nand.
Despite inconsistency, with mtd name like this specifying paritions
from the kernel command line becomes a torture (though, I didn't tried
and not sure if mtdparts= can handle spaces at all). Plus, this causes
real bugs when multiple fsl_elbc_nand chips registered.
With this patch applied fsl_elbc_nand chip will have proper name:
root@b1:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00800000 00010000 "fe000000.flash"
mtd1: 02000000 00004000 "e0600000.flash"
p.s. We can't use priv->dev->bus_id as in physmap_of, because
fsl_elbc_nand pretends to be a localbus controller, so its bus_id is
"address.localbus", which is incorrect and thus will also not work
for multiple chips.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is very simple driver, NAND is connected through localbus,
and User-Programmable Machine is doing various adjustments to
speak NAND. No special efforts needed to do read and write cycles,
though to control ALE and CLE phases, we ask UPM to generate exact
pre-programmed signals on the localbus lines.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for the SST 36VF3203 flash chip. It is used on Emerson
KSI8560 board.
Signed-off-by: Andrei Dolnikov <adolnikov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This enhances plat-ram to take a map_probes argument in
the platform_data structure which allow plat-ram to support
any direct-mapped device that MTD supports (jedec, cfi, amd ..)
A few items are also fixed:
- Don't panic if probes is 0
- Actually use the partition list that is passed in
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Untested, but shouldn't break anything... Makes MTD_XIP arch
independent. I guess this is why xip_iprefetch() was made for.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is preliminary since:
1. It supports only _one_ chip select at the moment. As there is no
existing platforms available using two chip selects of the NAND
controller, it shall really not include code for supporting the
2nd chip select for now, as such code cannot be verified.
2. It resorts to the default and simpliest memory based badblock
table
3. Only limited types of nand flash are currently supported. Most
PXA3xx processors come with on-chip NAND flash dies, so there
isn't much flexibility for other types of NAND.
4. The NAND controller should be configured to detect the device's
ID, thus making it difficult to use nand_scan_ident() to assist
the detection process (though it's not impossible)
TODO: fix all the above limitations of cuz :-)
Signed-off-by: eric miao <eric.miao@marvell.com>
Cc: Sergey Podstavin <spodstavin@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Return 0 partitions instead of -EINVAL on no mtdpart= argument in kernel
cmdline or missing partition info for device.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch extends the existing MAPS driver for the Nvidia CK804 chipset
(ck804xrom.c) to also work on the Nvidia MCP55 chipset. As both chipsets
are rather similar, suporting them both with the same driver is easy.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch makes the needlessly global struct rfd_ftl_tr static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch adds a proper prototype for onenand_bbt_read_oob() in
include/linux/mtd/onenand.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch makes the needlessly global cfi_staa_erase_varsize() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch makes the following needlessly global code static:
- ftl_freepart()
- struct ftl_tr
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Sparse spotted that 0 was compared to pointers.
While I was at it, I also moved the assignments out of the if's.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Every file should include the headers containing the externs for its
global functions (in this case for mtdram_init_device()).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch adds proper prototypes for nftl_{read,write}_oob() in
include/linux/mtd/nftl.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch adds proper prototypes for inftl_{read,write}_oob() in
include/linux/mtd/inftl.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Previously, a READ command was erroneously issued rather than SEQIN.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The part_probes[] should be static.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Jörn Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable MTD NAND
platform drivers, to re-enable auto loading.
NOTE: at91_nand for some reason disallows modular builds. I'm assuming that's
just an oversight that will be fixed.
[dbrownell@users.sourceforge.net: minor fix]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable MTD mapping
platform drivers, to re-enable auto loading.
NOTE oddness with physmap ... it's a legacy driver in some configs, which
means it can't always support hotplugging. (Not that most of these mapping
drivers would often be used as modules...)
[dbrownell@users.sourceforge.net: bugfix, more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I found this while I was looking how the rs_lib is working. The rs_decoder is
initialized _after_ the nand core code read the BBT table and _after_ the
partition table has been added. The driver has a private BBT description
which is in located in flash data so we Ooops if there is a bit flip _or_ if a
bit flips while reading the partition table.
This patch moves the initialization of the rs_lib before the first possible
access by nand core.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jörn Engel <joern@wh.fh-wedel.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for the ST M29W400DB flash chip. which is used on the GLAN Tank
NAS.
Signed-off-by: Gordon Farquharson <gordonfarquharson@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Address a number of small issues mainly regarding the output made by this
driver to dmesg:
- Some of the blkmtd's had not been changed to block2mtd which caused
display problem
- the parse_err() macro was displaying "block2mtd: " twice
Signed-off-by: Stéphane Chazelas <stephane.chazelas@emerson.com>
Acked-by: Jörn Engel <joern@lazybastard.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Make the needlessly global part_probes[] static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
struct oops_cxt needlessly became global.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Help out users by telling them the module name in the Kconfig help when
using the MTD_PHYSMAP option.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (202 commits)
[POWERPC] Fix compile breakage for 64-bit UP configs
[POWERPC] Define copy_siginfo_from_user32
[POWERPC] Add compat handler for PTRACE_GETSIGINFO
[POWERPC] i2c: Fix build breakage introduced by OF helpers
[POWERPC] Optimize fls64() on 64-bit processors
[POWERPC] irqtrace support for 64-bit powerpc
[POWERPC] Stacktrace support for lockdep
[POWERPC] Move stackframe definitions to common header
[POWERPC] Fix device-tree locking vs. interrupts
[POWERPC] Make pci_bus_to_host()'s struct pci_bus * argument const
[POWERPC] Remove unused __max_memory variable
[POWERPC] Simplify xics direct/lpar irq_host setup
[POWERPC] Use pseries_setup_i8259_cascade() in pseries_mpic_init_IRQ()
[POWERPC] Turn xics_setup_8259_cascade() into a generic pseries_setup_i8259_cascade()
[POWERPC] Move xics_setup_8259_cascade() into platforms/pseries/setup.c
[POWERPC] Use asm-generic/bitops/find.h in bitops.h
[POWERPC] 83xx: mpc8315 - fix USB UTMI Host setup
[POWERPC] 85xx: Fix the size of qe muram for MPC8568E
[POWERPC] 86xx: mpc86xx_hpcn - Temporarily accept old dts node identifier.
[POWERPC] 86xx: mark functions static, other minor cleanups
...
Print information about logicale eraseblock size, sub-page
size and so on at early stage, befor an attempt to attach
the MTD device was made. This is more convenient to do so
because the attempt to attach may fail, and the information
is never printed then.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
(a + b) / (c + d) != a / c + b / d. The old code errornously
assumed this incorrect formuld. Instead, just sum all erase
counters in a 64-bit variable and divide to the number of EBs
at the end.
Thanks to Adrian Hunter for pointing this out.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
I came across a problem which seems to be present since:
commit 941dfb07ed
UBI: set correct gluebi device size
ubi_create_gluebi() leaves mtd->size = 0 for static volumes. So even
existing static volumes are initialized with a size of 0.
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The new trend in linux is not to store headers which define
on-media format in the include/ directory, but instead, store
them locally. This is because these headers "do not define any
kernel<->userspace interface".
Do so for UBI as well.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Make I/O function to be always verbose when about CRC errors
and magic number errors when I/O debugging is enabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This is needed to support other localbus peripherals, such as
NAND on FSL UPM.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
cfi_amdstd_sync() and cfi_staa_sync() call schedule() without changing task's
state appropriately.
In case of e.g. chip->state == FL_ERASING, cfi_*_sync() will be busy-looping
either redundantly for a fixed interval of time (for SCHED_NORMAL tasks) or
possibly endlessly (for RT tasks and UP).
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
THe CFI driver in 2.6.24 kernel is broken. Not so intensive read/write
operations cause incomplete writes which lead to kernel panics in JFFS2.
We investigated the issue - it is caused by bug in FL_SHUTDOWN parsing code.
Sometimes chip returns -EIO as if it is in FL_SHUTDOWN state when it should
wait in FL_PONT (error in order of conditions).
The following patch fixes the bug in state parsing code of CFI. Also I've
added comments to notify developers if they want to add new case in future.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Reviewed-by: Joern Engel <joern@logfs.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
# reboot
...
[ 42.351266] Flash device refused suspend due to active operation (state 0)
[ 42.358195] Unable to handle kernel NULL pointer dereference at virtual address 00000078
[ 42.360060] pgd = c7d9c000
[ 42.362769] [00000078] *pgd=a7d8d031, *pte=00000000, *ppte=00000000
[ 42.372902] Internal error: Oops: 17 [#1]
[ 42.376911] Modules linked in:
[ 42.379980] CPU: 0 Not tainted (2.6.25-rc2-10642-ge8f2594-dirty #73)
[ 42.380000] PC is at physmap_flash_shutdown+0x28/0x54
...
[ 42.380000] Backtrace:
[ 42.380000] [<c0130c1c>] (physmap_flash_shutdown+0x0/0x54) from [<c01207c0>] (platform_drv_shutdown+0x20/0x24)
[ 42.380000] r5:28121969 r4:c0229e08
[ 42.380000] [<c01207a0>] (platform_drv_shutdown+0x0/0x24) from [<c011cd40>] (device_shutdown+0x60/0x88)
[ 42.380000] [<c011cce0>] (device_shutdown+0x0/0x88) from [<c003e8a4>] (kernel_restart_prepare+0x2c/0x3c)
[ 42.380000] r4:00000000
[ 42.380000] [<c003e878>] (kernel_restart_prepare+0x0/0x3c) from [<c003ea00>] (kernel_restart+0x14/0x48)
[ 42.380000] [<c003e9ec>] (kernel_restart+0x0/0x48) from [<c003fdc0>] (sys_reboot+0xe8/0x1f8)
[ 42.380000] r4:01234567
[ 42.380000] [<c003fcd8>] (sys_reboot+0x0/0x1f8) from [<c001aa00>] (ret_fast_syscall+0x0/0x2c)
[ 42.380000] r7:00000058 r6:00000004 r5:00000001 r4:00000000
[ 42.380000] Code: 0a000009 e7953004 e1a00003 e1a0e00f (e593f078)
[ 42.650051] ---[ end trace 6d6c26a0fc3141de ]---
Segmentation fault
INIT: no more processes left in this runlevel
While looping for mtd[i]s, we should stop at the mtd[i] == NULL.
This patch also removes unnecessary "if (info)" checks:
suspend/resume/shutdown ops are executed only if probe() is succeeded, so info
is guaranteed to be !NULL.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This has been forgotten in commit f5bbdacc41 ("[MTD] NAND Modularize
read function") and nobody compiled the driver.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Joern Engel <joern@wh.fh-wedel.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The block2mtd driver (drivers/mtd/devices/block2mtd.c) will kfree an on-stack
pointer when handling an invalid argument line (e.g.
block2mtd=/dev/loop0,xxx).
The kfree was added some time ago when "name" was dynamically allocated.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Acked-by: Joern Engel <joern@lazybastard.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: <stable@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a memory leak introduced by commit
4ccf8cffa9 and spotted by the Coverity
checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
In C, signed 1-bit bitfields can only take the values 0 and -1, only 0 and 1
are ever assigned in current code. Make them unsigned bitfields.
Fixes the (repeated) sparse errors:
drivers/mtd/ubi/ubi.h:220:15: error: dubious one-bit signed bitfield
drivers/mtd/ubi/ubi.h:221:17: error: dubious one-bit signed bitfield
drivers/mtd/ubi/ubi.h:222:18: error: dubious one-bit signed bitfield
drivers/mtd/ubi/ubi.h:223:16: error: dubious one-bit signed bitfield
drivers/mtd/ubi/ubi.h:224:20: error: dubious one-bit signed bitfield
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
drivers/mtd/ubi/vmt.c: In function `ubi_create_volume':
drivers/mtd/ubi/vmt.c:379: warning: statement with no effect
Signed-off-by: S.Çağlar Onur <caglar@pardus.org.tr>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
* Add path_put() functions for releasing a reference to the dentry and
vfsmount of a struct path in the right order
* Switch from path_release(nd) to path_put(&nd->path)
* Rename dput_path() to path_put_conditional()
[akpm@linux-foundation.org: fix cifs]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: <linux-fsdevel@vger.kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the central patch of a cleanup series. In most cases there is no good
reason why someone would want to use a dentry for itself. This series reflects
that fact and embeds a struct path into nameidata.
Together with the other patches of this series
- it enforced the correct order of getting/releasing the reference count on
<dentry,vfsmount> pairs
- it prepares the VFS for stacking support since it is essential to have a
struct path in every place where the stack can be traversed
- it reduces the overall code size:
without patch series:
text data bss dec hex filename
5321639 858418 715768 6895825 6938d1 vmlinux
with patch series:
text data bss dec hex filename
5320026 858418 715768 6894212 693284 vmlinux
This patch:
Switch from nd->{dentry,mnt} to nd->path.{dentry,mnt} everywhere.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix cifs]
[akpm@linux-foundation.org: fix smack]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implements kernel command line partitioning support for the CS5535/CS5536 chipsets driver.
For that the following is done:
* cs553x_cleanup(): try the cleanup for all chip selects to not leak memory
* Assign a unique name for each chip select to be separately addressable in the command line mtd-id portion(s)
* Use the already defined PIN_OPT_IDE constant where appropriate for readability
* Include command line partitioning support when CONFIG_MTD_PARTS is set
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* git://git.infradead.org/mtd-2.6: (120 commits)
[MTD] Fix mtdoops.c compilation
[MTD] [NOR] fix startup lock when using multiple nor flash chips
[MTD] [DOC200x] eccbuf is statically defined and always evaluate to true
[MTD] Fix maps/physmap.c compilation with CONFIG_PM
[MTD] onenand: Add panic_write function to the onenand driver
[MTD] mtdoops: Use the panic_write function when present
[MTD] Add mtd panic_write function pointer
[MTD] [NAND] Freescale enhanced Local Bus Controller FCM NAND support.
[MTD] physmap.c: Add support for multiple resources
[MTD] [NAND] Fix misparenthesization introduced by commit 78b65179...
[MTD] [NAND] Fix Blackfin NFC ECC calculating bug with page size 512 bytes
[MTD] [NAND] Remove wrong operation in PM function of the BF54x NFC driver
[MTD] [NAND] Remove unused variable in plat_nand_remove
[MTD] Unlocking all Intel flash that is locked on power up.
[MTD] [NAND] at91_nand: Make mtdparts option can override board info
[MTD] mtdoops: Various minor cleanups
[MTD] mtdoops: Ensure sequential write to the buffer
[MTD] mtdoops: Perform write operations in a workqueue
[MTD] mtdoops: Add further error return code checking
[MTD] [NOR] Test devtype, not definition in flash_probe(), drivers/mtd/devices/lart.c
...
drivers/mtd/mtdoops.c: In function ‘mtdoops_console_sync’:
drivers/mtd/mtdoops.c:329: error: implicit declaration of function ‘in_interrupt’
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Taken from http://bugzilla.kernel.org/show_bug.cgi?id=9829
I found and solved the problem, at line 115 of drivers/mtd/chips/gen_probe.c
(kernel 2.6.24): mapsize value must be calculated in bytes, not in long.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Acked-by: Joern Engel <joern@logfs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Implement the panic_write function for the onenand driver. This waits
for any active command to complete/timeout, performs the write, waits
for it to complete and then returns.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When the MTD provides a panic_write function, use it.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
MTDs are well suited for logging critical data and the mtdoops driver
allows kernel panics/oops to be written to flash in a blackbox flight
recorder fashion allowing better debugging and analysis of crashes.
Any kernel oops in user context can be easily handled since the kernel
continues as normal and any queued mtd writes are scheduled. Any kernel
oops in interrupt context results in a panic and the delayed writes will
not be scheduled however. The existing mtd->write function cannot be
called in interrupt context so these messages can never be written to
flash.
This patch adds a panic_write function pointer that drivers can
optionally implement which can be called in interrupt context. It is
only intended to be called when its known the kernel is about to panic
and we need to write to succeed. Since the kernel is not going to be
running for much longer, this function can break locks and delay to
ensure the write succeeds (but not sleep).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I have been prime author and maintainer of block2mtd from day one, but
neither MAINTAINERS nor the module source makes this fact clear. And while
I'm at it, update my email addresses tree-wide, as the old address
currently bounces and change my name to "joern" as unicode will likely
continue to cause trouble until the end of this century.
Signed-off-by: Joern Engel <joern@lazybastard.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch extends the physmap mapping driver to support multiple
resources for non-identical NOR chips that will be concatenated together
when selected.
This is needed for example for Intel 48F4400 512MBit chips, since they
consist of 2 single different NOR chips with different geometries. The
first (lower) one has botton boot sectors and the 2nd (upper) has top
boot sectors. This currently isn't handled correctly by calling the
physmap driver once with only one resource covering both chips in one
memory region. The same geometrie is used for both chips.
With this patch the following resource structure can be used to
describe the 48F4400 chip correctly:
static struct resource board_nor_resource[] = {
[0] = {
.start = 0xf8000000,
.end = 0xfbffffff,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = 0xfc000000,
.end = 0xffffffff,
.flags = IORESOURCE_MEM,
}
};
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
There is no suspend/resume operation in NFC driver at all, currently.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
With CONFIG_MTD_PARTITIONS not set, got this:
drivers/mtd/nand/plat_nand.c:113: warning: unused variable 'pdata'
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Patch for unlocking all Intel flash that has instant locking on power up.
The patch has been tested on Intel M18, P30 and J3D Strata Flash.
1. The automatic unlocking can be disabled for a particular partition
in the map or the command line.
a. For the bit mask in the map it should look like:
.mask_flags = MTD_POWERUP_LOCK,
b. For the command line parsing it should look like:
mtdparts=0x80000(bootloader)lk
2. This will only unlock parts with instant individual block locking.
Intel parts with legacy unlocking will not be unlocked.
Signed-off-by: Justin Treon <justin_treon@yahoo.com>
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Call parse_mtd_partitions before checking board's partition_info, so
that "mtdparts=" option can override board's default setting.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Various minor cleaups to mtdoops:
* Don't support the mtd->erasesize < OOPS_PAGE_SIZE case
* Tweak printks and make the device mtdoops connects to more visible
* CON_PRINTBUFFER flag is uneeded
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add a spinlock to ensure writes to the mtdoops buffer memory are
sequential and don't race.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Writing to the flash needs to be done in a workqueue. The console
write functions may be called in any context which can lead to
lockups otherwise.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add further error return code checks to the mtdoops driver.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/devices/lart.c:119:#define FLASH_DEVICE_16mbit_BOTTOM 0x88f488f4
As was, unless "manufacturer != FLASH_MANUFACTURER" this returned true
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/ubi/scan.c: In function 'ubi_scan':
drivers/mtd/ubi/scan.c:772: warning: 'ec' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/ubi/wl.c:746: warning: 'pe' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is just not necessary. We re-write whole layout copy, so
the old contents cannot show up again sice scan process will
drop it.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
In function onenand_verify_oob, local variable oobbuf shall be unsigned char.
In the case of a value is >= 0x80, it's unequal in comparing the value in an unsigned char and signed char.
Signed-off-by: Sheng Yongjie (Sam) <samsheng@trident.com.cn>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Consolidate OneNAND operation order as OneNAND Spec.
It also doesn't break previous operation order.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The single-bit error correction was, well, incorrect. For determing which
bit to correct it was using P1' P2' P4' P8' instead of P1 P2 P4 P8, and
it was using P16' P32' P64' P128' P256' P512' P1024' P2048' instead of
P16 P32 P64 P128 P256 P512 P1024 P2048.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Instead of passing vol_id to all functions and then find
struct ubi_volume, pass struct ubi_volume pointer.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since we do not change semantics of seek(), changing the file
pointer while updating does not make much sense.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Add more information about layout volume to make userspace tools
use the macros instead of constants. Also rename UBI_LAYOUT_VOL_ID
to make it consistent with other macros.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Old gcc complains:
CC drivers/mtd/ubi/wl.o
drivers/mtd/ubi/wl.c: In function 'wear_leveling_worker':
drivers/mtd/ubi/wl.c:746: warning: 'pe' may be used uninitialized in this function
CC drivers/mtd/ubi/scan.o
drivers/mtd/ubi/scan.c: In function 'ubi_scan':
drivers/mtd/ubi/scan.c:772: warning: 'ec' may be used uninitialized in this function
drivers/mtd/ubi/scan.c:772: note: 'ec' was declared here
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since the data offset parameter was removed, the size of
the parameters array is now 2, not 3.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The problem: NAND flashes have different amount of initial bad physical
eraseblocks (marked as bad by the manufacturer). For example, for 256MiB
Samsung OneNAND flash there might be from 0 to 40 bad initial eraseblocks,
which is about 2%. When UBI is used as the base system, one needs to know
the exact amount of good physical eraseblocks, because this number is
needed to create the UBI image which is put to the devices during
production. But this number is not know, which forces us to use the
minimum number of good physical eraseblocks. And UBI additionally
reserves some percentage of physical eraseblocks for bad block handling
(default is 1%), so we have 1-3% of PEBs reserved at the end, depending
on the amount of initial bad PEBs. But it is desired to always have
1% (or more, depending on the configuration).
Solution: this patch adds an "auto-resize" flag to the volume table.
The volume which has the "auto-resize" flag will automatically be re-sized
(enlarged) on the first UBI initialization. UBI clears the flag when
the volume is re-sized. Only one volume may have the "auto-resize" flag.
So, the production UBI image may have one volume with "auto-resize"
flag set, and its size is automatically adjusted on the first boot
of the device.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
drivers/mtd/ubi/cdev.c: In function ‘vol_cdev_read’:
drivers/mtd/ubi/cdev.c:187: warning: unused variable ‘vol_id’
CC [M] drivers/mtd/ubi/kapi.o
drivers/mtd/ubi/kapi.c: In function ‘ubi_leb_erase’:
drivers/mtd/ubi/kapi.c:483: warning: unused variable ‘vol_id’
drivers/mtd/ubi/kapi.c: In function ‘ubi_leb_unmap’:
drivers/mtd/ubi/kapi.c:544: warning: unused variable ‘vol_id’
drivers/mtd/ubi/kapi.c: In function ‘ubi_leb_map’:
drivers/mtd/ubi/kapi.c:582: warning: unused variable ‘vol_id’
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This slab cache is not really needed since the number of objects
is low and the constructor does not make much sense because we
allocate oblects when doint I/O, which is way slower then allocation.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
struct class_device is going away, this converts the code to use struct
device instead.
Signed-off-by: Tony Jones <tonyj@suse.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If there were multiple bit errors in the data s3c2410_nand_correct_data()
was returning 0 (no error) instead of -1, so the upper layers (like JFFS2)
would not know the data is corrupt.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The bug causes corruptions of data read from flash.
The original code performs cache invalidation from "adr" to "adr + len"
in do_write_buffer(). Since len and adr could be updated in the code
before invalidation - it causes improper setting of cache invalidation
regions.
Signed-off-by: Massimo Cirillo <maxcir@gmail.com>
Signed-off-by: Giuseppe D'Eliseo <giuseppedeliseo@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jörn Engel <joern@logfs.org>
Signed-off-by: David Woohouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to "Common Flash Memory Interface Publication 100" dated December 1,
2001, the interface code for x16/x32 chips is 0x0005, and not 0x0004 used so
far.
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Some hardware, such as the enhanced local bus controller used on some
mpc83xx chips, does ecc transparently when reading and writing data, rather
than providing a generic calculate/correct mechanism that can be exported to
the nand subsystem.
The subsystem should not BUG() when calculate, correct, or hwctl are
missing, if the methods that call them have been overridden.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
"include/linux/mtd/mtd.h" declares "mtd_oob_ops.retlen" as size_t, which
is 64 bits on targets with a 64 bit addressing. The MEMWRITEOOB ioctl
calls copy_to_user() to write it back to "mtd_oob_buf.length", which is
declared in "include/linux/mtd-abi.h" as uint32_t. Since powerpc is a
big endian architecture, this only copies the upper 32 bits of the
address, which is always 0.
Signed-off-by: David Scidmore <dscidmore@xes-inc.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When creating a new volume, do not forget to increment the
vol_count variable.
Also, users are not interested in internal volumes, so do not show
them in the volumes_count sysfs file.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
UBI allows to specify MTD device name or number when the module is being
loaded. When parsing MTD device identity string, it first tries to treat
it as device NAME, and if that fails, it treats it as device number.
Make it vice-versa as this is more logical and makes less troubles when
you have an MTD device named "1" and try to load mtd1 which has different
name. This is especially easy to hit when gluebi is enabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Introduce a separate mutex which serializes volumes checking,
because we cammot really use volumes_mutex - it cases reverse
locking problems with mtd_tbl_mutex when gluebi is used -
thanks to lockdep.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Prepare the attach and detach functions to by used outside of
module initialization:
* detach function checks reference count before detaching
* it kills the background thread as well
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This is one more step on the way to "removable" UBI devices. It
adds reference counting for UBI devices. Every time a volume on
this device is opened - the device's refcount is increased. It
is also increased if someone is reading any sysfs file of this
UBI device or of one of its volumes.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
