Currently, when tring to set up a serial console with a higher
baud rate, it would fallback to 921600.
Tested-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for sparse variable sampling rates on SCIFA and SCIFB.
According to the datasheet, sampling rate 1/5 needs a small quirk to
avoid corrupting the first byte received.
This increases the range and accuracy of supported baud rates.
E.g. on r8a7791/koelsch:
- Supports now 134, 150, and standard 500000-4000000 bps,
- Perfect match for 134, 150, 500000, 1000000, 2000000, and 4000000
bps,
- Accuracy has increased for most standard bps values.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the single sampling rate and special handling for HSCIF's
variable sampling rates by a bitmask and a custom iterator.
This prepares for the advent of SCIFA/SCIFB's sparse variable sampling
rates.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On SCIx variants different from HSCIF, the bit rate is equal to the
sampling clock rate divided by half the sampling rate. Currently this is
handled by dividing the sampling rate by two, which was OK as it was
always even.
Replace halving the sampling rate by premultiplying the base clock
frequency by 2, to accommodate odd sampling rates on SCIFA/SCIFB later.
Replace the shift value in the BRG divider calculation by a
premultiplication of the base clock frequency too, for consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIFA and SCIFB have additional bit rate config bits in the Serial Mode
Register. Don't touch them when using the port as a serial console, as
we rely on the boot loader to have configured the serial port config.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a non console i.MX UART is enabled in the device tree,
system suspend fails due to an unprepared clock:
[ 638.794563] PM: Syncing filesystems ... done.
[ 638.878902] Freezing user space processes ... (elapsed 0.002 seconds) done.
[ 638.888454] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 638.996697] PM: suspend of devices complete after 97.200 msecs
[ 639.002611] PM: suspend devices took 0.100 seconds
[ 639.013020] PM: late suspend of devices complete after 2.288 msecs
[ 639.021486] ------------[ cut here ]------------
[ 639.026147] WARNING: CPU: 0 PID: 488 at drivers/clk/clk.c:732 clk_core_enable+0xc0/0x12c()
[ 639.034413] Modules linked in:
[ 639.037490] CPU: 0 PID: 488 Comm: system_server Tainted: G W 4.4.0-rc5-pknbsp-svn2214-atag-v4.4-rc5-121-gebfd9cb #1304
[ 639.049312] Hardware name: Freescale i.MX53 (Device Tree Support)
[ 639.055444] [<c0016d54>] (unwind_backtrace) from [<c00140f8>] (show_stack+0x20/0x24)
[ 639.063199] [<c00140f8>] (show_stack) from [<c02c99a0>] (dump_stack+0x20/0x28)
[ 639.070442] [<c02c99a0>] (dump_stack) from [<c0024ca8>] (warn_slowpath_common+0x88/0xc0)
[ 639.078541] [<c0024ca8>] (warn_slowpath_common) from [<c0024d0c>] (warn_slowpath_null+0x2c/0x34)
[ 639.087332] [<c0024d0c>] (warn_slowpath_null) from [<c05171e8>] (clk_core_enable+0xc0/0x12c)
[ 639.095777] [<c05171e8>] (clk_core_enable) from [<c05172f8>] (clk_enable+0x2c/0x40)
[ 639.103441] [<c05172f8>] (clk_enable) from [<c0349880>] (imx_serial_port_suspend_noirq+0x20/0xe0)
[ 639.112336] [<c0349880>] (imx_serial_port_suspend_noirq) from [<c03a26a0>] (dpm_run_callback+0x68/0x16c)
[ 639.121825] [<c03a26a0>] (dpm_run_callback) from [<c03a2898>] (__device_suspend_noirq+0xf4/0x22c)
[ 639.130705] [<c03a2898>] (__device_suspend_noirq) from [<c03a4b0c>] (dpm_suspend_noirq+0x148/0x30c)
[ 639.139764] [<c03a4b0c>] (dpm_suspend_noirq) from [<c00511d4>] (suspend_devices_and_enter+0x2e8/0x6a4)
[ 639.149078] [<c00511d4>] (suspend_devices_and_enter) from [<c00518a0>] (pm_suspend+0x310/0x4b8)
[ 639.157782] [<c00518a0>] (pm_suspend) from [<c00500ec>] (state_store+0x7c/0xcc)
[ 639.165099] [<c00500ec>] (state_store) from [<c02cb6dc>] (kobj_attr_store+0x1c/0x28)
[ 639.172858] [<c02cb6dc>] (kobj_attr_store) from [<c01633d4>] (sysfs_kf_write+0x54/0x58)
[ 639.180871] [<c01633d4>] (sysfs_kf_write) from [<c01629b4>] (kernfs_fop_write+0x100/0x1c8)
[ 639.189152] [<c01629b4>] (kernfs_fop_write) from [<c00fb8b8>] (__vfs_write+0x3c/0xe8)
[ 639.196991] [<c00fb8b8>] (__vfs_write) from [<c00fc810>] (vfs_write+0xa4/0x160)
[ 639.204307] [<c00fc810>] (vfs_write) from [<c00fcac4>] (SyS_write+0x4c/0x98)
[ 639.211363] [<c00fcac4>] (SyS_write) from [<c0010760>] (ret_fast_syscall+0x0/0x3c)
This does not happen for the common case of a single UART used as a console
(since imx_console_setup() already does a prepare)
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
start_tx and the ISR used largely identical code to transmit data.
Consolidate that in one place.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the _OFFSET suffix from all register defines which makes code a
little easier to read and avoids a few line breaks.
Suggested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handling magic sysrq included dropping a lock to avoid a deadlock that
happened when cdns_uart_console_write tried to acquire a lock in the
from the sysrq code path. By making the acquisition of the lock in
cdns_uart_console_write depending on port->sysrq, cdns_uart_handle_rx can be
simplified to simply call uart_handle_sysrq.
Suggested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert an if-else into the more common early return on error, reducing
the indent level of the happy path.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The system could deadlock handling RX IRQs when RX-related IRQ
conditions became true while the receiver was disabled. To avoid this,
enable/disable the RX/TX IRQs together with the receiver/transmitter.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Request_irq() should be _after_ h/w programming, otherwise an
interrupt could be triggered and in-progress before the h/w has been
setup.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move RX-related IRQ handling into a helper function.
Fixes a problem where every char received after a parity or frame error
in the current isr will also be tagged as a parity or frame error.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shutting down the UART port can happen while console operations are in
progress. Holding the port lock serializes these operations and avoids
the UART HW to be disabled in the middle of console prints.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RX path in the interrupt handler released a lock unnecessarily.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The startup function is supposed to initialize the UART for receiving.
Hence, don't enable the TX part. Also, protect HW accesses with the port
lock.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When shutting down the UART, clear the interrupt status register. Bits
in the ISR are cleared by writing them as '1'.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restarting the transmitter even if the circ buffer is empty may be
necessary to push out remaining data when the port is restarted after
being stopped.
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of disabling the IRQ, use the spin lock to serialize accesses to
the HW. This protects the driver from interference of non-IRQ callbacks
with each other and makes the driver more consistent in its
serialization method.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"earlyprintk" is architecture specific option.
General "earlycon" option support is much better.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
[uli: preserve other SCSCR bits when asserting RE and TE]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
[geert: rewording, #ifdef rework]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Considering that pci_pericom_setup(()'s only difference to
pci_default_setup() is the setting of the uartclk field, and taking
into account that this field already gets taken care of by having the
base_baud field filled in the pci_boards[] entries, there's no need
for both the function and the quirks table entry.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use to_pci_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pl011 driver has gone back and forth on the definition of the
ZTE specific variation of the hardware definitions, but the
current state is that the vendor definition is left in place
yet unused:
drivers/tty/serial/amba-pl011.c:190:27: warning: 'vendor_zte' defined but not used [-Wunused-variable]
I don't know what the plan forward is to get this code to work,
but the current behavior is a bit annoying as we get a warning
whenever we build this driver.
This patch does not help us to make it work, but at least
shuts up the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 7ec7587189 ("tty: amba-pl011: add support for ZTE UART (EXPERIMENTAL)")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Busy loops that poll on a register should call cpu_relax(). On some
architectures, it can lower CPU power consumption or yield to a
hyperthreaded twin processor. It also serves as a compiler barrier,
so it can replace barrier() calls.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In datasheet, Modem Status Register MSR[4-7] reflect the modem pins
CTS/DSR/RI/CD signal state.
Signed-off-by: Wills Wang <wills.wang@live.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In all functions other than atmel_serial_probe_fifos,
atmel_serial_probe, and atmel_console_init, the name "port" is used to
refer to an instance of struct uart_port. In many of these functions,
"atmel_port" is used to refer to an instance of struct atmel_uart_port.
We make the use of the name "port" consistent by making
atmel_serial_probe_fifos, atmel_serial_probe, and atmel_console_init
use "atmel_port" to refer to an instance of struct atmel_uart_port
instead of the previous name of "port".
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Acked-by: Karthik Manamcheri <karthik.manamcheri@ni.com>
[nicolas.ferre@atmel.com: fix typo in variable, adapt to newer kernel]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with sama5d2, the new UART revision has an hardware timer. So, add it
to the IP detection code and set the "has_hw_timer" property for it.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functional change is associated with this patch.
A driver property depends on the Atmel serial IP revision. This property
is the way the rx timeout is handled: by an hardware or software timer.
So, change this property name and setup code so that it's easier to understand
and more future proof as the distinction of USART vs. UART is blurrier on newer
SoCs.
Variable names and debug comments are also adapted to make this code more obvious.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some UART HW has a single register combining UART_DLL/UART_DLM
(this was probably forgotten in the change that introduced the
callbacks, commit b32b19b8ff)
Fixes: b32b19b8ff ("[SERIAL] 8250: set divisor register correctly ...")
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's old, messy and mostly unmaintained.
Remove it as suggested by Peter Hurley and Alan.
Signed-off-by: Frederik Völkel <frederik.voelkel@fau.de>
Signed-off-by: Lukas Braun <lukas.braun@fau.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Constifies psc_ops structures in tty's serial
port driver since they are not modified after
their initialization.
Detected and found using Coccinelle.
Suggested-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Direct call to readl()/writel() is checked against iotype
and in case of UPIO_MEM32BE we use ioread32be()/iowrite32be()
instead of them.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for UPIO_MEM32BE in addition to UPIO_MEM32.
For big endian we use 2 new accessors similar to little endian,
called dw8250_serial_out32be() and dw8250_serial_in32be().
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the help of Heikki we take common code that
makes sure LCR write wasn't ignored and put it in new function called
dw8250_check_lcr(). This function serves 3 serial_out routines:
dw8250_serial_out(), dw8250_serial_out32(), and dw8250_serial_outq().
This patch only brings better code reuse.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use software emulated RS485 direction control to provide RS485 API
existed in omap_serial driver. Note that 8250_omap issues interrupt
on shift register empty which is single prerequesite for using software
emulated RS485.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implementation of software emulation of RS485 direction handling is based
on omap_serial driver.
Before and after transmission RTS is set to the appropriate value.
Note that before calling serial8250_em485_init() the caller has to
ensure that UART will interrupt when shift register empty. Otherwise,
emultaion cannot be used.
Both serial8250_em485_init() and serial8250_em485_destroy() are
idempotent functions.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Software RS485 emultaion is to be added in the following commit.
serial8250_start_tx() will need to refer serial8250_stop_rx().
Move serial8250_stop_rx() in front of serial8250_start_tx() in order
to avoid function forward declaration.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct uart_sio_port has a lots of unused members. Some of them are
set to some constant but never read. Remove all those.
This includes removal of uart_ops->pm handler as we never handle pm
(pm was never set).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DEBUG_AUTOCONF is unused.
Switch DEBUG_INTR to pr_debug. This is only enabled with DEBUG or
dynamic debug when explicitly asked for.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only variables in old_serial_port are port and irq. So make
old_serial_port contain only those two and move the initialization of
the rest to the place where old_serial_port is actually read.
Also get rid of SERIAL_PORT_DFNS. It is ugly and having the
initializer where it belongs makes more sense. Finally, use already
defined UART_NR in the loop.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only needed information from the header is struct old_serial_port.
Move it to m32r_sio.c, make it const and anonymous. And kill the rest
from the header as it is dead stuff.
Given m32r_sio_suspend_port and m32r_sio_resume_port are local to
m32r_sio.c and unused, kill them from .c too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a remnant from the dark age. Nobody uses the macro now, so
remove.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: <linux-xtensa@linux-xtensa.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since check_name and check_resources return only 0/1, switch them to
bool/true/false.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a chain of up to 4 nested ifs in init and remove functions.
Instead, make the code linear and use goto's to handle failures.
Remove unneeded cast from mpsc_release_port by referencing pi->port
directly. And finally, use dev_dbg instead of pr_debug given we have
dev->dev node.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When mpsc_routing_base, sdma_intr_base, mpsc_base, sdma_base, and
brg_base are mapped, they are never unmapped. The condition in the
free paths is always 'if (!XXX_base) { unmap }'. Fix it by inverting
the condition.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add DT earlycon for 8250_omap driver. This boot console is included
for kernels built with CONFIG_SERIAL_EARLYCON=y, CONFIG_OF=y,
CONFIG_SERIAL_8250_OMAP=y, and CONFIG_OF_EARLY_FLATTREE=y.
This boot console is enabled with the command line option "earlycon"
(without "=<name>...") when the DT 'stdout-path' property matches a
compatible uart. For example,
/ {
chosen {
stdout-path = "serial0:115200";
};
....
aliases {
serial0 = &uart0;
};
....
ocp : ocp {
uart0 : serial@44e09000 {
compatible = "ti,omap3-uart";
}
};
};
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>