This patch updates some register setting according to recommendation
from HW designer and experiment.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use ACPI "_RST" method to reset the controller, since FLR is not
supported.
Function hisi_sas_stop_phys() is introduced to remove some code
duplication.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds calls to kill CQ takslets v3 hw during probe failure.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The channel interrupt is to process all the interrupts except PHY
UP/DOWN and broadcast interrupt. So we need to clear all the interrupts
except those 3 interrupts after processing channel interrupts.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify STP link timer from 10ms to 500ms. Also add the register address.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For v3 hw, internal abort function required status and command buffer to
be set, so add necessary code for this.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add two ATA commands, ATA_CMD_ZAC_MGMT_IN and ATA_CMD_ZAC_MGMT_OUT in
hisi_sas_get_ata_protocol(), to support SATA SMR disk.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is a fix related to freeing a device in v2 hw driver.
Before, we polled to ITCT CLR interrupt to check if a device is free.
This was error prone, as if the interrupt doesn't occur in 10us, we miss
processing it.
To avoid this situation, service this interrupt and sync the event with
a completion.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support to clean-up allocated IRQs and kill tasklets
when probe fails and for driver removal.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch removes some repeated configurations:
(1) The device id of the device is already set in the alloc function, so
we don't need to modify in free device function.
(2) Field dev_type and dev_status are configured in hisi_sas_dev_gone(),
so there is no need for repeated config in free_device_v3_hw.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code to print ECC errors in v2 hw driver is very repetitive. This
patch condensed the code by looping an array of errors.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add DFX feature for v2 hw. We are adding support for
the following errors:
- loss_of_dword_sync_count
- invalid_dword_count
- phy_reset_problem_count
- running_disparity_error_count
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The value dw0 is the residual bytes when UNDERFLOW error happens, but we
filled the residual with the value of dw3 before. So change the residual
from dw3 to dw0.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When some interrupts happen together, we need to process every interrupt
one-by-one, and should not return immediately when one interrupt process
is finished being processed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provides fixes for the following issues:
1. Fix issue of controller reset required to send commands. For reset
process, it may be required to send commands to the controller, but
not during soft reset. So add HISI_SAS_NOT_ACCEPT_CMD_BIT to prevent
executing a task during this period.
2. Send a broadcast event in rescan topology to detect any topology
changes during reset.
3. Previously it was not ensured that libsas has processed the PHY up
and down events after reset. Potentially this could cause an issue
that we still process the PHY event after reset. So resolve this by
flushing shot workqueue in LLDD reset.
4. Port ID requires refresh after reset. The port ID generated after
reset is not guaranteed to be the same as before reset, so it needs
to be refreshed for each device's ITCT.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver’s PCI IDs to match the latest Microsemi controllers
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add PQI reset to driver shutdown callback to work around controller bug.
During an 1.) OS shutdown or 2.) kexec outside of a kdump, the Linux
kernel will clear BME on our controller.
If BME is cleared during a controller/host PCIe transfer, the controller
will lock up.
So we perform a PQI reset in the driver's shutdown callback function to
eliminate the possibility of a controller/host PCIe transfer being
active when the kernel clears BME immediately after calling the driver's
shutdown callback.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- make pass-thru requests bi-directional
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- distinguish between shutdown and non-shutdown.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The null check on pHba->channel[chan].device is redundant because
device is an array and hence can never be null. Remove the check.
Detected by CoverityScan, CID#115362 ("Array compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The return value of dma_map_single() should be checked by
dma_mapping_error(). However, in function qla26xx_dport_diagnostics(), its
return value is checked against NULL, which could result in failures.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The return value of scsi_host_alloc() should be released by
scsi_host_put(). However, in function mvs_pci_init(), kfree()
is used. This patch replaces kfree() with scsi_host_put() to avoid
possible memory leaks.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function pm8001_pci_probe(), on errors that the control flow jumps to
label err_out_ha_free, function pm8001_free() is called. In pm8001_free(),
scsi_host_put() is called to release shost, which keeps the return value
of scsi_host_alloc(). After pm8001_free() returns, kfree() is called to
free shost again, resulting in a double free bug. This patch removes
scsi_host_put() from pm8001_free() and explicitly calls scsi_host_put()
to release Scsi_Host in need.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fix allocate instance->pd_info twice which was introduced by 96188a89cc.
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After sending a message, always clear esp->msg_out_len. Otherwise,
eh_abort_handler may subsequently fail to send an ABORT TASK SET
message.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch improves readability. There are no functional changes.
Since this touches on a questionable ESP_INTR_DC conditional, add some
commentary to help others who may (as I did) find themselves chasing an
"Invalid Command" error after the device flags this condition.
This cleanup also eliminates a warning from "make W=1":
drivers/scsi/esp_scsi.c: In function 'esp_finish_select':
drivers/scsi/esp_scsi.c:1233:5: warning: variable 'orig_select_state' set but not used [-Wunused-but-set-variable]
u8 orig_select_state;
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When in MESSAGE IN phase, the ESP device does not automatically
acknowledge each byte that is transferred by PIO. The mac_esp driver
neglects to explicitly ack them, which causes a timeout during messages
larger than one byte (e.g. tag bytes during reconnect). Fix this with an
ESP_CMD_MOK command after each byte.
The MESSAGE IN phase is also different in that each byte transferred
raises ESP_INTR_FDONE. So don't exit the transfer loop for this interrupt,
for this phase.
That resolves the "Reconnect IRQ2 timeout" error on those Macs which use
PIO transfers instead of PDMA. This patch also improves on the weak tests
for unexpected interrupts and phase changes during PIO transfers.
Tested-by: Stan Johnson <userm57@yahoo.com>
Fixes: 02507a80b3 ("[PATCH] [SCSI] mac_esp: fix PIO mode, take 2")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid the following warning from "make C=1":
CHECK drivers/scsi/mac_esp.c
drivers/scsi/mac_esp.c:357:30: warning: incorrect type in initializer (different address spaces)
drivers/scsi/mac_esp.c:357:30: expected unsigned char [usertype] *fifo
drivers/scsi/mac_esp.c:357:30: got void [noderef] <asn:2>*
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add const to bin_attribute structures as they are only passed to the
functions system_{remove/create}_bin_file. The arguments passed are of
type const, so declare the structures to be const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If cxgbi_ep_connect() is called with valid shost then find associated
ndev and use ndev->ifindex to find route.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the lines above this test, 8 'kzalloc' are performed, but only 7
results are tested.
Add the missing one (i.e. '!ioc->port_enable_cmds.reply').
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Regenerate firmware files to make cleaner base for following fix.
This removes some unused definitions and reorders some #defines, but
the code remains the same.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We need to override Kbuild rules for copying shipped files, otherwise
aic7xxx_reg.h and aic7xxx_reg_print.c will be ovewritten by old versions.
Fixes: 516b7db593
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ahc_platform_dump_card_state() does nothing. Remove it.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Scsi_cmnd is an unsuitable argument for eh_device_reset_handler(),
eh_target_reset_handler(), and eh_host_reset_handler() which do not have
the scope of one single SCSI command. These callbacks tend to use
fc_block_scsi_eh() requiring scsi_cmnd. In order to start decoupling
above eh callbacks from scsi_cmnd, introduce a new variant of the
function called fc_block_rport() taking an fc_rport as argument.
Refactor the old fc_block_scsi_eh() to simply delegate to
fc_block_rport().
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support to the driver to set the exchange threshold value for
the number of outstanding AENs.
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality.
Following cleanups have been done as requested by reviewer
- Changed waitQ --> waitq
- Collapsed multiple debug statements into single
- Remove extra parentheses in if-else as per operator precedence
- Remove unnecessary casting
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's better to use the DRIVER_ATTR_RW() and DRIVER_ATTR_RO() macros to
explicitly show that this is a read/write or read/only sysfs file. So
convert the remaining SCSI drivers that use the old style to use the
newer macros.
Bonus is that this removes some checkpatch.pl warnings :)
This is part of a series to drop DRIVER_ATTR() from the tree entirely.
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: Willem Riede <osst@riede.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We print a 256 byte event string into a buffer that is only 161
bytes long, this is clearly wrong:
drivers/scsi/gdth_proc.c: In function 'gdth_show_info':
drivers/scsi/gdth.c:3660:41: error: '%s' directive writing up to 255 bytes into a region of size between 141 and 150 [-Werror=format-overflow=]
sprintf(buffer,"Adapter %d: %s\n",
^~
/git/arm-soc/drivers/scsi/gdth.c:3660:13: note: 'sprintf' output between 13 and 277 bytes into a destination of size 161
sprintf(buffer,"Adapter %d: %s\n",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
dvr->eu.async.ionode,dvr->event_string);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
gcc calculates that the worst case buffer size would be 277 bytes,
so we can use that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The MSI interrupt name can require 11 bytes in addition to the device name,
for a total of 23 bytes:
drivers/scsi/fnic/fnic_isr.c: In function 'fnic_request_intr':
drivers/scsi/fnic/fnic_isr.c:192:4: error: '-fcs-rq' directive writing 7 bytes into a region of size between 5 and 16 [-Werror=format-overflow=]
"%.11s-fcs-rq", fnic->name);
drivers/scsi/fnic/fnic_isr.c:206:3: note: 'sprintf' output between 12 and 23 bytes into a destination of size 16
sprintf(fnic->msix[FNIC_MSIX_ERR_NOTIFY].devname,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%.11s-err-notify", fnic->name);
This extends the buffer to fit any possible value.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
gcc notices that we would overflow the buffer for the
inquiry of the product name if we have too many adapters:
drivers/scsi/gdth.c: In function 'gdth_next':
drivers/scsi/gdth.c:2357:29: warning: 'sprintf' may write a terminating nul past the end of the destination [-Wformat-overflow=]
sprintf(inq.product,"Host Drive #%02d",t);
^~~~~~~~~~~~~~~~~~~
drivers/scsi/gdth.c:2357:9: note: 'sprintf' output between 16 and 17 bytes into a destination of size 16
sprintf(inq.product,"Host Drive #%02d",t);
This won't happen in practice, so just use snprintf to
truncate the string.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We print the driver name into one string and then add and ID
and copy it into a second string of the same length, at which
point gcc complains about a possible overflow:
drivers/scsi/mpt3sas/mpt3sas_scsih.c: In function '_scsih_probe':
drivers/scsi/mpt3sas/mpt3sas_scsih.c:8884:21: error: '_cm' directive writing 3 bytes into a region of size between 1 and 32 [-Werror=format-overflow=]
printf(ioc->name, "%s_cm%d", ioc->driver_name, ioc->id);
^~~~~~~~~
drivers/scsi/mpt3sas/mpt3sas_scsih.c:8884:21: note: directive argument in the range [0, 255]
drivers/scsi/mpt3sas/mpt3sas_scsih.c:8884:2: note: 'sprintf' output between 5 and 38 bytes into a destination of size 32
sprintf(ioc->name, "%s_cm%d", ioc->driver_name, ioc->id);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Making the first string shorter is sufficient to avoid the
warning here, as we know it can only contain either "mpt2sas"
or "mpt3sas".
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
gcc-7 complains that the firmware version strings might overflow
for some values:
drivers/scsi/megaraid.c: In function 'megaraid_probe_one':
drivers/scsi/megaraid.c:314:33: error: '%d' directive writing between 1 and 2 bytes into a region of size between 1 and 2 [-Werror=format-overflow=]
drivers/scsi/megaraid.c:314:33: note: directive argument in the range [0, 15]
drivers/scsi/megaraid.c:314:3: note: 'sprintf' output between 7 and 9 bytes into a destination of size 7
drivers/scsi/megaraid.c:320:35: error: '%d' directive writing between 1 and 2 bytes into a region of size between 1 and 2 [-Werror=format-overflow=]
drivers/scsi/megaraid.c:320:35: note: directive argument in the range [0, 15]
drivers/scsi/megaraid.c:320:3: note: 'sprintf' output between 7 and 9 bytes into a destination of size 7
This makes the code use a truncating snprintf() instead, which shuts
up that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API. It also updates
some comments, accordingly.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API. It also updates
the name of some variables and the content of comments, accordingly.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Limit PDMA send to 512 B to avoid data corruption on DTC3181E. The
corruption is always the same: one byte missing at the beginning of a
128 B block. It happens only with slow Quantum LPS 240 drive, not with
faster IBM DORS-32160. It's not clear what causes this. Documentation
for the DTC436 chip has not been made available.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The polling loops in pread() and pwrite() can easily become infinite
loops and hang the machine.
Merge the IRQ check into host buffer wait loop and add polling limit.
Also place a limit on polling for 53C80 registers accessibility.
[Use NCR5380_poll_politely2() for register polling. Rely on polling for
gated IRQ rather than polling for phase error, like the algorithm in the
53c400 datasheet. Move DTC436 workarounds into a separate patch.
Factor-out common code as wait_for_53c80_access(). Rework the residual
calculations. -- F.T.]
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The word "read" may be used to mean "DMA read operation" or "SCSI READ
command", though a READ command implies writing to memory.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an IRQ arrives during PDMA transfer, pread() and pwrite() return
without waiting for the 53C80 registers to be ready and this ends up
messing up the chip state. This was observed with SONY CDU-55S which is
slow enough to disconnect during 4096-byte reads.
IRQ during PDMA is not an error so don't return -1. Instead, store the
remaining byte count for use by NCR5380_dma_residual().
[Poll for the BASR_END_DMA_TRANSFER condition rather than remove the
error message -- F.T.]
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
generic_NCR5380_dma_xfer_len() incorrectly uses cmd->transfersize which
causes rescan-scsi-bus and CD-ROM access to hang the system. Use
cmd->SCp.this_residual instead, like other NCR5380 drivers.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When issuing a bus reset we should complete all commands, not
just the command triggering the reset.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To correctly identify which fib has a scsi command callback this
patch implements a flag FIB_CONTEXT_FLAG_SCSI_CMD.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
aac_hba_send() will return FAILED for any non-SCSI command requests,
failing any TMFs. This patch updates the check to allow TMFs.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When sending a reset fib we shouldn't rely on the scsi command,
but rather set the TMF status in the map_info->reset_state variable.
That allows us to send a TMF independent on a scsi command.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Split off device, target, and bus reset functionality into
individual functions.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Split off the host reset parts of aac_eh_reset() into a separate
host reset function.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Split off reset FIB generation into separate functions.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This seven is mostly minor build, Kconfig and error leg fixes.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJZgeACAAoJEAVr7HOZEZN4vxwP/0GZc1EWDubS8DZZOr4X25WA
jofQFCrWYf9jBcCA64pv7kF5wCbQk0MFXMvs2u5YHGMV8U4VyquNT2zEYm+R5ZD8
C3sIdgZyxb7x+KkUJ5NxvDBIzAQuQcPEUPZspgi809veoATQ28qoMO1NkOJzbJGE
nUs/6TZcpA5xGdqXtI3G6IsbvuAFO1hmI2aIUAj5UVKV+B9ILGsxWHPzYPErgtra
afTJ8jO4vYW/wcyY7/DG/V8UAvU/0pe9NZqgt0Gn+XiSq5C9HnqS9+BWjU9nx98g
EiPuvP6UBq7zGmjFQdUTwYuysbPDwyVfB1l7RJFVeBTPj6sINFrqTQPU8qwy96S8
gxfObnfbEkx4zJmv4iP8HtAgRQMVsVN64ICD6oeS4JQWmXoz90S0vCLwrTQv36ll
UHmBaSKMqPHTt+emEmup3rcOBU+4PIVq40jQjUyBCJXd/kg5GUz7Og++/NHX8JDZ
qhVJ/VhkBacnDD9fZLQ2cMfcB/E5pUmEgx3MycZty8pXx0AkttWyB0lIddln2yiL
qpZwbJ4nbhS7TO1/ScZlHEqp/rVY3aaIvLovWrhrmy4N1KBk41EmSxCokxkv+Kmd
Twy35eHLDT9Hn0emT+y12Ul5y0cTxy1JMOcMf6LLXAHQsKgg2khm3JfHcXC7H4mO
H/FpxwQT7z47yU3FF2mZ
=/+Ot
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"These seven patches are mostly minor build, Kconfig and error leg
fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qedi: Fix return code in qedi_ep_connect()
scsi: lpfc: fix linking against modular NVMe support
scsi: scsi_transport_fc: return -EBUSY for deleted vport
scsi: libcxgbi: add check for valid cxgbi_task_data
scsi: aic7xxx: fix firmware build with O=path
scsi: megaraid_sas: fix memleak in megasas_alloc_cmdlist_fusion
scsi: qedi: Add ISCSI_BOOT_SYSFS to Kconfig
Three small fixes. The transfer size fixes are actually correcting
some performance drops on the hpsa and smartpqi cards. The cards
actually have an internal cache for request speed up but bypass it for
transfers > 1MB. Since 4.3 the efficiency of our merges has rendered
the cache mostly unused, so limit transfers to under 1MB to recover
the cache boost.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=7jN6
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three small fixes.
The transfer size fixes are actually correcting some performance drops
on the hpsa and smartpqi cards. The cards actually have an internal
cache for request speed up but bypass it for transfers > 1MB. Since
4.3 the efficiency of our merges has rendered the cache mostly unused,
so limit transfers to under 1MB to recover the cache boost"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sg: fix static checker warning in sg_is_valid_dxfer
scsi: smartpqi: limit transfer length to 1MB
scsi: hpsa: limit transfer length to 1MB
We shouldn't be writing over the "ret" variable. It means we return
ERR_PTR(0) which is NULL and it results in a NULL dereference in the
caller.
Fixes: ace7f46ba5 ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When LPFC is built-in but NVMe is a loadable module, we fail to link the
kernel:
drivers/scsi/built-in.o: In function `lpfc_nvme_create_localport':
(.text+0x156a82): undefined reference to `nvme_fc_register_localport'
drivers/scsi/built-in.o: In function `lpfc_nvme_destroy_localport':
(.text+0x156eaa): undefined reference to `nvme_fc_unregister_remoteport'
We can avoid this either by forcing lpfc to be a module, or by disabling
NVMe support in this case. This implements the former.
Fixes: 7d7080335f ("scsi: lpfc: Finalize Kconfig options for nvme")
Cc: stable@vger.kernel.org
Link: https://patchwork.kernel.org/patch/9636569/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When trying to delete a vport via 'vport_delete' sysfs attribute we
should be checking if the port is already in state VPORT_DELETING; if so
there's no need to do anything.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In error case it is possible that ->cleanup_task() gets called without
calling ->alloc_pdu() in this case cxgbi_task_data is not valid, so add
a check for for valid cxgbi_task_data in cxgbi_cleanup_task().
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Building firmware with O=path was apparently broken in aic7 for ever.
Message of the previous commit to the Makefile (from 2008) mentions this
unfortunate state of affairs already. Fix this, mostly to make
randconfig builds more reliable.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qedi uses iscsi_boot_sysfs to export the targets used for boot to
sysfs. Select the config option to make sure the module is built.
This addresses the compile time issue,
drivers/scsi/qedi/qedi_main.o: In function `qedi_remove':
qedi_main.c:(.text+0x3bbd): undefined reference to `iscsi_boot_destroy_kset'
drivers/scsi/qedi/qedi_main.o: In function `__qedi_probe.constprop.0':
qedi_main.c:(.text+0x577a): undefined reference to `iscsi_boot_create_target'
qedi_main.c:(.text+0x5807): undefined reference to `iscsi_boot_create_target'
qedi_main.c:(.text+0x587f): undefined reference to `iscsi_boot_create_initiator'
qedi_main.c:(.text+0x58f3): undefined reference to `iscsi_boot_create_ethernet'
qedi_main.c:(.text+0x5927): undefined reference to `iscsi_boot_destroy_kset'
qedi_main.c:(.text+0x5d7b): undefined reference to `iscsi_boot_create_host_kset'
[mkp: fixed whitespace]
Signed-off-by: Nilesh Javali <nilesh.javali@cavium.com>
Fixes: c57ec8fb7c ("scsi: qedi: Add support for Boot from SAN over iSCSI offload")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
dxfer_len is an unsigned int and we always assign a value > 0 to it, so
it doesn't make any sense to check if it is < 0. We can't really check
dxferp as well as we have both NULL and not NULL cases in the possible
call paths.
So just return true for SG_DXFER_FROM_DEV transfer in
sg_is_valid_dxfer().
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: Colin Ian King <colin.king@canonical.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The smartpqi firmware will bypass the cache for any request larger than
1MB, so we should cap the request size to avoid any performance
degradation in kernels later than v4.3
This degradation is caused from d2be537c3b,
which changed max_sectors_kb to 1280k, but the hardware is able to
work fine with it, so the true fix should be from smartpqi driver.
Signed-off-by: Yadan Fan <ydfan@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hpsa firmware will bypass the cache for any request larger than 1MB,
so we should cap the request size to avoid any performance degradation
in kernels later than v4.3
This degradation is caused from d2be537c3b,
which changed max_sectors_kb to 1280k, but the hardware is able to work
fine with it, so the true fix should be from hpsa driver.
Signed-off-by: Yadan Fan <ydfan@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is actually just a small set of mainly bug fixes for the original
merge window code plus a few trivial updates and qedi boot from SAN
support feature patch.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=XhC/
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is actually just a small set of mainly bug fixes for the original
merge window code plus a few trivial updates and qedi boot from SAN
support feature patch"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: libfc: pass an error pointer to fc_disc_error()
scsi: hisi_sas: make several const arrays static
scsi: qla2xxx: Off by one in qlt_ctio_to_cmd()
scsi: sg: fix SG_DXFER_FROM_DEV transfers
scsi: virtio_scsi: always read VPD pages for multiqueue too
scsi: qedf: fix spelling mistake: "offlading" -> "offloading"
scsi: qedi: fix another spelling mistake: "alloction" -> "allocation"
scsi: isci: fix typo in function names
scsi: cxlflash: return -EFAULT if copy_from_user() fails
scsi: qedi: Add support for Boot from SAN over iSCSI offload
Pull SCSI target updates from Nicholas Bellinger:
"It's been usually busy for summer, with most of the efforts centered
around TCMU developments and various target-core + fabric driver bug
fixing activities. Not particularly large in terms of LoC, but lots of
smaller patches from many different folks.
The highlights include:
- ibmvscsis logical partition manager support (Michael Cyr + Bryant
Ly)
- Convert target/iblock WRITE_SAME to blkdev_issue_zeroout (hch +
nab)
- Add support for TMR percpu LUN reference counting (nab)
- Fix a potential deadlock between EXTENDED_COPY and iscsi shutdown
(Bart)
- Fix COMPARE_AND_WRITE caw_sem leak during se_cmd quiesce (Jiang Yi)
- Fix TMCU module removal (Xiubo Li)
- Fix iser-target OOPs during login failure (Andrea Righi + Sagi)
- Breakup target-core free_device backend driver callback (mnc)
- Perform TCMU add/delete/reconfig synchronously (mnc)
- Fix TCMU multiple UIO open/close sequences (mnc)
- Fix TCMU CHECK_CONDITION sense handling (mnc)
- Fix target-core SAM_STAT_BUSY + TASK_SET_FULL handling (mnc + nab)
- Introduce TYPE_ZBC support in PSCSI (Damien Le Moal)
- Fix possible TCMU memory leak + OOPs when recalculating cmd base
size (Xiubo Li + Bryant Ly + Damien Le Moal + mnc)
- Add login_keys_workaround attribute for non RFC initiators (Robert
LeBlanc + Arun Easi + nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (68 commits)
iscsi-target: Add login_keys_workaround attribute for non RFC initiators
Revert "qla2xxx: Fix incorrect tcm_qla2xxx_free_cmd use during TMR ABORT"
tcmu: clean up the code and with one small fix
tcmu: Fix possbile memory leak / OOPs when recalculating cmd base size
target: export lio pgr/alua support as device attr
target: Fix return sense reason in target_scsi3_emulate_pr_out
target: Fix cmd size for PR-OUT in passthrough_parse_cdb
tcmu: Fix dev_config_store
target: pscsi: Introduce TYPE_ZBC support
target: Use macro for WRITE_VERIFY_32 operation codes
target: fix SAM_STAT_BUSY/TASK_SET_FULL handling
target: remove transport_complete
pscsi: finish cmd processing from pscsi_req_done
tcmu: fix sense handling during completion
target: add helper to copy sense to se_cmd buffer
target: do not require a transport_complete for SCF_TRANSPORT_TASK_SENSE
target: make device_mutex and device_list static
tcmu: Fix flushing cmd entry dcache page
tcmu: fix multiple uio open/close sequences
tcmu: drop configured check in destroy
...
This patch is basically to silence a static checker warning.
drivers/scsi/libfc/fc_disc.c:326 fc_disc_error()
warn: passing a valid pointer to 'PTR_ERR'
It doesn't affect runtime because it treats -ENOMEM and a valid pointer
the same. But the documentation says we should be passing an error
pointer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don't populate various tables on the stack but make them static const.
Makes the object code smaller by over 280 bytes:
Before:
text data bss dec hex filename
39887 5080 64 45031 afe7 hisi_sas_v2_hw.o
After:
text data bss dec hex filename
39318 5368 64 44750 aece hisi_sas_v2_hw.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are "req->num_outstanding_cmds" elements in the
req->outstanding_cmds[] array so the > here should be >=.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SG_DXFER_FROM_DEV transfers do not necessarily have a dxferp as we set
it to NULL for the old sg_io read/write interface, but must have a
length bigger than 0. This fixes a regression introduced by commit
28676d869b ("scsi: sg: check for valid direction before starting the
request")
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: 28676d869b ("scsi: sg: check for valid direction before starting the request")
Reported-by: Chris Clayton <chris2553@googlemail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Multi-queue virtio-scsi uses a different scsi_host_template struct. Add
the .device_alloc field there, too.
Fixes: 25d1d50e23
Cc: stable@vger.kernel.org
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake in QEDF_INFO message and remove
duplicated "since" (thanks to Tyrel Datwyler for spotting the latter
issue).
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake in QEDF_ERR message. I should have also
included this in a previous fix, but I only just spotted this one.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are a couple of typos in function names and spelling of request
where the letters u and e are swapped:
scu_ssp_reqeust_construct_task_context
scu_sata_reqeust_construct_task_context
Fix the spelling of request.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The copy_from/to_user() functions return the number of bytes remaining
to be copied but we had intended to return -EFAULT here.
Fixes: bc88ac47d5 ("scsi: cxlflash: Support AFU debug")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for Boot from SAN over iSCSI offload. The iSCSI
boot information in the NVRAM is populated under
/sys/firmware/iscsi_bootX/ using qed NVM-image reading API and further
exported to open-iscsi to perform iSCSI login enabling boot over offload
iSCSI interface in a Boot from SAN environment.
Signed-off-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@cavium.com>
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: Nilesh Javali <nilesh.javali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull more block updates from Jens Axboe:
"This is a followup for block changes, that didn't make the initial
pull request. It's a bit of a mixed bag, this contains:
- A followup pull request from Sagi for NVMe. Outside of fixups for
NVMe, it also includes a series for ensuring that we properly
quiesce hardware queues when browsing live tags.
- Set of integrity fixes from Dmitry (mostly), fixing various issues
for folks using DIF/DIX.
- Fix for a bug introduced in cciss, with the req init changes. From
Christoph.
- Fix for a bug in BFQ, from Paolo.
- Two followup fixes for lightnvm/pblk from Javier.
- Depth fix from Ming for blk-mq-sched.
- Also from Ming, performance fix for mtip32xx that was introduced
with the dynamic initialization of commands"
* 'for-linus' of git://git.kernel.dk/linux-block: (44 commits)
block: call bio_uninit in bio_endio
nvmet: avoid unneeded assignment of submit_bio return value
nvme-pci: add module parameter for io queue depth
nvme-pci: compile warnings in nvme_alloc_host_mem()
nvmet_fc: Accept variable pad lengths on Create Association LS
nvme_fc/nvmet_fc: revise Create Association descriptor length
lightnvm: pblk: remove unnecessary checks
lightnvm: pblk: control I/O flow also on tear down
cciss: initialize struct scsi_req
null_blk: fix error flow for shared tags during module_init
block: Fix __blkdev_issue_zeroout loop
nvme-rdma: unconditionally recycle the request mr
nvme: split nvme_uninit_ctrl into stop and uninit
virtio_blk: quiesce/unquiesce live IO when entering PM states
mtip32xx: quiesce request queues to make sure no submissions are inflight
nbd: quiesce request queues to make sure no submissions are inflight
nvme: kick requeue list when requeueing a request instead of when starting the queues
nvme-pci: quiesce/unquiesce admin_q instead of start/stop its hw queues
nvme-loop: quiesce/unquiesce admin_q instead of start/stop its hw queues
nvme-fc: quiesce/unquiesce admin_q instead of start/stop its hw queues
...
This reverts commit 5f572526a1.
As reported by Pascal here:
http://www.spinics.net/lists/target-devel/msg15808.html
there still appears to be another issue related to this change
to drop the original bogus tcm_qla2xxx_free_cmd() usage from
tcm_qla2xxx_handle_data_work() and tcm_qla2xxx_aborted_task().
So revert this for now, until Pascal can verify with further
debug in place to understand what's going on.
Reported-by: Pascal de Bruijn <p.debruijn@unilogic.nl>
Cc: Pascal de Bruijn <p.debruijn@unilogic.nl>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: Quinn Tran <quinn.tran@cavium.com>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch drops two incorrect usages of tcm_qla2xxx_free_cmd()
during TMR ABORT within tcm_qla2xxx_handle_data_work() and
tcm_qla2xxx_aborted_task(), which where attempting to dispatch
into workqueue context to do tcm_qla2xxx_complete_free() and
subsequently invoke transport_generic_free_cmd().
This is incorrect because during TMR ABORT target-core will
drop the outstanding se_cmd->cmd_kref references once it has
quiesced the se_cmd via transport_wait_for_tasks(), and in
the case of qla2xxx it should not attempt to do it's own
transport_generic_free_cmd() once the abort has occured.
As reported by Pascal, this was originally manifesting as a
BUG_ON(cmd->cmd_in_wq) in qlt_free_cmd() during TMR ABORT,
with a LIO backend that had sufficently high enough WRITE
latency to trigger a host side TMR ABORT_TASK.
In addition, for the case in tcm_qla2xxx_write_pending_status()
and tcm_qla2xxx_handle_data_work() that waits for outstanding
FCP WRITE data transfer to complete before preceeding with a
TMR ABORT, avoid se_cmd->t_transport_stop_comp that is already
used by transport_wait_for_tasks() and use a qla2xxx internal
struct completion instead.
Reported-by: Pascal de Bruijn <p.debruijn@unilogic.nl>
Tested-by: Pascal de Bruijn <p.debruijn@unilogic.nl>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: Quinn Tran <quinn.tran@cavium.com>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
ibmvscsis always returned 0 for the tpg/tag, since it did not
parse the value passed in by the user.
When functions like ALUA members exports the value, it will
be incorrect because targetcli/rtslib starts the tpg numbering
at 1.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Following Himanshu's earlier patch to drop the redundant tag
lookup within __qlt_24xx_handle_abts(), go ahead and drop this
now QLA_TGT_ABTS can use TARGET_SCF_LOOKUP_LUN_FROM_TAG and
have target_submit_tmr() do this from common code.
Reviewed-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Quinn Tran <quinn.tran@cavium.com>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
