If the in-service bfq_queue is sync and remains temporarily idle, then
I/O dispatching (from other queues) may be plugged. It may be dome for
two reasons: either to boost throughput, or to preserve the bandwidth
share of the in-service queue. In the first case, if the I/O of the
in-service queue, when it finally arrives, consists only of one small
I/O request, then it makes sense to plug even the I/O of the in-service
queue. In fact, serving such a small request immediately is likely to
lower throughput instead of boosting it, whereas waiting a little bit is
likely to let that request grow, thanks to request merging, and become
more profitable in terms of throughput (this is likely to happen exactly
because the I/O of the queue has been detected to boost throughput).
On the opposite end, if I/O dispatching is being plugged only to
preserve the bandwidth of the in-service queue, then it would be better
not to plug also the I/O of the in-service queue, because such a
plugging is likely to cause only loss of bandwidth for the queue.
Unfortunately, no distinction is made between the two cases, and the I/O
of the in-service queue is always plugged in case just a small I/O
request arrives. This commit draws this missing distinction and does not
perform harmful plugging.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is a preparatory commit for commits that need to check only one of
the two main reasons for idling. This change should also improve the
quality of the code a little bit, by splitting a function that contains
very long, non-trivial and little related comments.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In asymmetric scenarios, i.e., when some bfq_queue or bfq_group needs to
be guaranteed a different bandwidth than other bfq_queues or bfq_groups,
these service guaranteed can be provided only by plugging I/O dispatch,
completely or partially, when the queue in service remains temporarily
empty. A case where asymmetry is particularly strong is when some active
bfq_queues belong to a higher-priority class than some other active
bfq_queues. Unfortunately, this important case is not considered at all
in the code for detecting asymmetric scenarios. This commit adds the
missing logic.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Before commit 18e5a57d79 ("block, bfq: postpone rq preparation to
insert or merge"), the destination queue for a request was chosen by a
different hook than the one that then inserted the request. So, between
the execution of the two hooks, the bic of the process generating the
request could happen to be redirected to a different bfq_queue. As a
consequence, the destination bfq_queue stored in the request could be
wrong. Such an event does not need to ba handled any longer.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With some unlucky sequences of events, the function bfq_updated_next_req
updates the current budget of a bfq_queue to a lower value than the
service received by the queue using such a budget. Unfortunately, if
this happens, then the return value of the function bfq_bfqq_budget_left
becomes inconsistent. This commit solves this problem by lower-bounding
the budget computed in bfq_updated_next_req to the service currently
charged to the queue.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
To boost throughput on devices with internal queueing and in scenarios
where device idling is not strictly needed, bfq immediately starts
serving a new bfq_queue if the in-service bfq_queue remains without
pending I/O, even if new I/O may arrive soon for the latter queue. Then,
if such I/O actually arrives soon, bfq preempts the new in-service
bfq_queue so as to give the previous queue a chance to go on being
served (in case the previous queue should actually be the one to be
served, according to its timestamps).
However, the in-service bfq_queue, say Q, may also be without further
budget when it remains also pending I/O. Since bfq changes budgets
dynamically to fit the needs of bfq_queues, this happens more often than
one may expect. If this happens, then there is no point in trying to go
on serving Q when new I/O arrives for it soon: Q would be expired
immediately after being selected for service. This would only cause
useless overhead. This commit avoids such a useless selection.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The speed at which a bfq_queue receives I/O is one of the parameters by
which bfq decides whether the queue is soft real-time (i.e., whether the
queue contains the I/O of a soft real-time application). In particular,
when a bfq_queue remains without outstanding I/O requests, bfq computes
the minimum time instant, named soft_rt_next_start, at which the next
request of the queue may arrive for the queue to be deemed as soft real
time.
Unfortunately this filtering may cause problems with a queue in
interactive weight raising. In fact, such a queue may be conveying the
I/O needed to load a soft real-time application. The latter will
actually exhibit a soft real-time I/O pattern after it finally starts
doing its job. But, if soft_rt_next_start is updated for an interactive
bfq_queue, and the queue has received a lot of service before remaining
with no outstanding request (likely to happen on a fast device), then
soft_rt_next_start is assigned such a high value that, for a very long
time, the queue is prevented from being possibly considered as soft real
time.
This commit removes the updating of soft_rt_next_start for bfq_queues in
interactive weight raising.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If debugfs were to return a non-NULL error for a debugfs call, using
that pointer later in debugfs_create_files() would crash.
Fix that by properly checking the pointer before referencing it.
Reported-by: Michal Hocko <mhocko@kernel.org>
Reported-and-tested-by: syzbot+b382ba6a802a3d242790@syzkaller.appspotmail.com
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Florian reported a io hung issue when fsync(). It should be
triggered by following race condition.
data + post flush a flush
blk_flush_complete_seq
case REQ_FSEQ_DATA
blk_flush_queue_rq
issued to driver blk_mq_dispatch_rq_list
try to issue a flush req
failed due to NON-NCQ command
.queue_rq return BLK_STS_DEV_RESOURCE
request completion
req->end_io // doesn't check RESTART
mq_flush_data_end_io
case REQ_FSEQ_POSTFLUSH
blk_kick_flush
do nothing because previous flush
has not been completed
blk_mq_run_hw_queue
insert rq to hctx->dispatch
due to RESTART is still set, do nothing
To fix this, replace the blk_mq_run_hw_queue in mq_flush_data_end_io
with blk_mq_sched_restart to check and clear the RESTART flag.
Fixes: bd166ef1 (blk-mq-sched: add framework for MQ capable IO schedulers)
Reported-by: Florian Stecker <m19@florianstecker.de>
Tested-by: Florian Stecker <m19@florianstecker.de>
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
syzbot is hitting flush_work() warning caused by commit 4d43d395fe
("workqueue: Try to catch flush_work() without INIT_WORK().") [1].
Although that commit did not expect INIT_WORK(NULL) case, calling
flush_work() without setting a valid callback should be avoided anyway.
Fix this problem by setting a no-op callback instead of NULL.
[1] https://syzkaller.appspot.com/bug?id=e390366bc48bc82a7c668326e0663be3b91cbd29
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-and-tested-by: syzbot <syzbot+ba2a929dcf8e704c180e@syzkaller.appspotmail.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We can't touch a bio after ->make_request_fn(), for all we know it could
already have been completed by the time this function returns.
This reverts commit 698cef1739.
Reported-by: syzbot+4df6ca820108fd248943@syzkaller.appspotmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch avoids that sparse reports the following warnings:
CHECK block/blk-wbt.c
block/blk-wbt.c:600:6: warning: symbol 'wbt_issue' was not declared. Should it be static?
block/blk-wbt.c:620:6: warning: symbol 'wbt_requeue' was not declared. Should it be static?
CC block/blk-wbt.o
block/blk-wbt.c:600:6: warning: no previous prototype for wbt_issue [-Wmissing-prototypes]
void wbt_issue(struct rq_qos *rqos, struct request *rq)
^~~~~~~~~
block/blk-wbt.c:620:6: warning: no previous prototype for wbt_requeue [-Wmissing-prototypes]
void wbt_requeue(struct rq_qos *rqos, struct request *rq)
^~~~~~~~~~~
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Swap REQ_NOWAIT and REQ_NOUNMAP and add REQ_HIPRI.
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Except for blk_queue_split(), bio_split() is used for splitting bio too,
then the remained bio is often resubmit to queue via generic_make_request().
So the same queue enter recursion exits in this case too. Unfortunatley
commit cd4a4ae468 doesn't help this case.
This patch covers the above case by setting BIO_QUEUE_ENTERED before calling
q->make_request_fn.
In theory the per-bio flag is used to simulate one stack variable, it is
just fine to clear it after q->make_request_fn is returned. Especially
the same bio can't be submitted from another context.
Fixes: cd4a4ae468 ("block: don't use blocking queue entered for recursive bio submits")
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: NeilBrown <neilb@suse.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove the imprecise and sloppy:
"This files is licensed under the GPL."
license notice in the top level comment.
1) The file already contains a SPDX license identifier which clearly
states that the license of the file is GPL V2 only
2) The notice resolves to GPL v1 or later for scanners which is just
contrary to the intent of SPDX identifiers to provide clear and non
ambiguous license information. Aside of that the value add of this
notice is below zero,
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Matias Bjorling <mb@lightnvm.io>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Fixes: 6a5ac98465 ("block: Make struct request_queue smaller for CONFIG_BLK_DEV_ZONED=n")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We need to pass bio->bi_opf after bio intergrity preparing, otherwise
the flag of REQ_INTEGRITY may not be set on the allocated request, then
breaks block integrity.
Fixes: f9afca4d36 ("blk-mq: pass in request/bio flags to queue mapping")
Cc: Hannes Reinecke <hare@suse.com>
Cc: Keith Busch <keith.busch@intel.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Comments on function __bfq_deactivate_entity contains two imprecise or
wrong statements:
1) The function performs the deactivation of the entity.
2) The function must be invoked only if the entity is on a service tree.
This commits replaces both statements with the correct ones:
1) The functions updates sched_data and service trees for the entity,
so as to represent entity as inactive (which is only part of the steps
needed for the deactivation of the entity).
2) The function must be invoked on every entity being deactivated.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 5f0ed774ed ("block: sum requests in the plug structure") removed
the request_count parameter from block_attempt_plug_merge(), but did not
remove the associated kerneldoc comment, introducing this warning to the
docs build:
./block/blk-core.c:685: warning: Excess function parameter 'request_count' description in 'blk_attempt_plug_merge'
Remove the obsolete description and make things a little quieter.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There was some confusion about what these functions did. Make it clear
that this is a hint for upper layers to pass to the block layer, and
that it does not guarantee that I/O will not be submitted between a
start and finish plug.
Reported-by: "Darrick J. Wong" <darrick.wong@oracle.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=KYFj
-----END PGP SIGNATURE-----
Merge tag 'for-4.21/block-20190102' of git://git.kernel.dk/linux-block
Pull more block updates from Jens Axboe:
- Dead code removal for loop/sunvdc (Chengguang)
- Mark BIDI support for bsg as deprecated, logging a single dmesg
warning if anyone is actually using it (Christoph)
- blkcg cleanup, killing a dead function and making the tryget_closest
variant easier to read (Dennis)
- Floppy fixes, one fixing a regression in swim3 (Finn)
- lightnvm use-after-free fix (Gustavo)
- gdrom leak fix (Wenwen)
- a set of drbd updates (Lars, Luc, Nathan, Roland)
* tag 'for-4.21/block-20190102' of git://git.kernel.dk/linux-block: (28 commits)
block/swim3: Fix regression on PowerBook G3
block/swim3: Fix -EBUSY error when re-opening device after unmount
block/swim3: Remove dead return statement
block/amiflop: Don't log error message on invalid ioctl
gdrom: fix a memory leak bug
lightnvm: pblk: fix use-after-free bug
block: sunvdc: remove redundant code
block: loop: remove redundant code
bsg: deprecate BIDI support in bsg
blkcg: remove unused __blkg_release_rcu()
blkcg: clean up blkg_tryget_closest()
drbd: Change drbd_request_detach_interruptible's return type to int
drbd: Avoid Clang warning about pointless switch statment
drbd: introduce P_ZEROES (REQ_OP_WRITE_ZEROES on the "wire")
drbd: skip spurious timeout (ping-timeo) when failing promote
drbd: don't retry connection if peers do not agree on "authentication" settings
drbd: fix print_st_err()'s prototype to match the definition
drbd: avoid spurious self-outdating with concurrent disconnect / down
drbd: do not block when adjusting "disk-options" while IO is frozen
drbd: fix comment typos
...
- support -y option for merge_config.sh to avoid downgrading =y to =m
- remove S_OTHER symbol type, and touch include/config/*.h files correctly
- fix file name and line number in lexer warnings
- fix memory leak when EOF is encountered in quotation
- resolve all shift/reduce conflicts of the parser
- warn no new line at end of file
- make 'source' statement more strict to take only string literal
- rewrite the lexer and remove the keyword lookup table
- convert to SPDX License Identifier
- compile C files independently instead of including them from zconf.y
- fix various warnings of gconfig
- misc cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=r3Fl
-----END PGP SIGNATURE-----
Merge tag 'kconfig-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kconfig updates from Masahiro Yamada:
- support -y option for merge_config.sh to avoid downgrading =y to =m
- remove S_OTHER symbol type, and touch include/config/*.h files correctly
- fix file name and line number in lexer warnings
- fix memory leak when EOF is encountered in quotation
- resolve all shift/reduce conflicts of the parser
- warn no new line at end of file
- make 'source' statement more strict to take only string literal
- rewrite the lexer and remove the keyword lookup table
- convert to SPDX License Identifier
- compile C files independently instead of including them from zconf.y
- fix various warnings of gconfig
- misc cleanups
* tag 'kconfig-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (39 commits)
kconfig: surround dbg_sym_flags with #ifdef DEBUG to fix gconf warning
kconfig: split images.c out of qconf.cc/gconf.c to fix gconf warnings
kconfig: add static qualifiers to fix gconf warnings
kconfig: split the lexer out of zconf.y
kconfig: split some C files out of zconf.y
kconfig: convert to SPDX License Identifier
kconfig: remove keyword lookup table entirely
kconfig: update current_pos in the second lexer
kconfig: switch to ASSIGN_VAL state in the second lexer
kconfig: stop associating kconf_id with yylval
kconfig: refactor end token rules
kconfig: stop supporting '.' and '/' in unquoted words
treewide: surround Kconfig file paths with double quotes
microblaze: surround string default in Kconfig with double quotes
kconfig: use T_WORD instead of T_VARIABLE for variables
kconfig: use specific tokens instead of T_ASSIGN for assignments
kconfig: refactor scanning and parsing "option" properties
kconfig: use distinct tokens for type and default properties
kconfig: remove redundant token defines
kconfig: rename depends_list to comment_option_list
...
This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas. Additionally, we have
a pile of annotation, unused variable and minor updates. The big API
change is the updates for Christoph's DMA rework which include
removing the DISABLE_CLUSTERING flag. And finally there are a couple
of target tree updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXCEUNiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdjKAP9vrTTv
qFaYmAoRSbPq9ZiixaXLMy0K/6o76Uay0gnBqgD/fgn3jg/KQ6alNaCjmfeV3wAj
u1j3H7tha9j1it+4pUw=
=GDa+
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas.
Additionally, we have a pile of annotation, unused variable and minor
updates.
The big API change is the updates for Christoph's DMA rework which
include removing the DISABLE_CLUSTERING flag.
And finally there are a couple of target tree updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (259 commits)
scsi: isci: request: mark expected switch fall-through
scsi: isci: remote_node_context: mark expected switch fall-throughs
scsi: isci: remote_device: Mark expected switch fall-throughs
scsi: isci: phy: Mark expected switch fall-through
scsi: iscsi: Capture iscsi debug messages using tracepoints
scsi: myrb: Mark expected switch fall-throughs
scsi: megaraid: fix out-of-bound array accesses
scsi: mpt3sas: mpt3sas_scsih: Mark expected switch fall-through
scsi: fcoe: remove set but not used variable 'port'
scsi: smartpqi: call pqi_free_interrupts() in pqi_shutdown()
scsi: smartpqi: fix build warnings
scsi: smartpqi: update driver version
scsi: smartpqi: add ofa support
scsi: smartpqi: increase fw status register read timeout
scsi: smartpqi: bump driver version
scsi: smartpqi: add smp_utils support
scsi: smartpqi: correct lun reset issues
scsi: smartpqi: correct volume status
scsi: smartpqi: do not offline disks for transient did no connect conditions
scsi: smartpqi: allow for larger raid maps
...
-----BEGIN PGP SIGNATURE-----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=TRdW
-----END PGP SIGNATURE-----
Merge tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"This is the main pull request for block/storage for 4.21.
Larger than usual, it was a busy round with lots of goodies queued up.
Most notable is the removal of the old IO stack, which has been a long
time coming. No new features for a while, everything coming in this
week has all been fixes for things that were previously merged.
This contains:
- Use atomic counters instead of semaphores for mtip32xx (Arnd)
- Cleanup of the mtip32xx request setup (Christoph)
- Fix for circular locking dependency in loop (Jan, Tetsuo)
- bcache (Coly, Guoju, Shenghui)
* Optimizations for writeback caching
* Various fixes and improvements
- nvme (Chaitanya, Christoph, Sagi, Jay, me, Keith)
* host and target support for NVMe over TCP
* Error log page support
* Support for separate read/write/poll queues
* Much improved polling
* discard OOM fallback
* Tracepoint improvements
- lightnvm (Hans, Hua, Igor, Matias, Javier)
* Igor added packed metadata to pblk. Now drives without metadata
per LBA can be used as well.
* Fix from Geert on uninitialized value on chunk metadata reads.
* Fixes from Hans and Javier to pblk recovery and write path.
* Fix from Hua Su to fix a race condition in the pblk recovery
code.
* Scan optimization added to pblk recovery from Zhoujie.
* Small geometry cleanup from me.
- Conversion of the last few drivers that used the legacy path to
blk-mq (me)
- Removal of legacy IO path in SCSI (me, Christoph)
- Removal of legacy IO stack and schedulers (me)
- Support for much better polling, now without interrupts at all.
blk-mq adds support for multiple queue maps, which enables us to
have a map per type. This in turn enables nvme to have separate
completion queues for polling, which can then be interrupt-less.
Also means we're ready for async polled IO, which is hopefully
coming in the next release.
- Killing of (now) unused block exports (Christoph)
- Unification of the blk-rq-qos and blk-wbt wait handling (Josef)
- Support for zoned testing with null_blk (Masato)
- sx8 conversion to per-host tag sets (Christoph)
- IO priority improvements (Damien)
- mq-deadline zoned fix (Damien)
- Ref count blkcg series (Dennis)
- Lots of blk-mq improvements and speedups (me)
- sbitmap scalability improvements (me)
- Make core inflight IO accounting per-cpu (Mikulas)
- Export timeout setting in sysfs (Weiping)
- Cleanup the direct issue path (Jianchao)
- Export blk-wbt internals in block debugfs for easier debugging
(Ming)
- Lots of other fixes and improvements"
* tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block: (364 commits)
kyber: use sbitmap add_wait_queue/list_del wait helpers
sbitmap: add helpers for add/del wait queue handling
block: save irq state in blkg_lookup_create()
dm: don't reuse bio for flushes
nvme-pci: trace SQ status on completions
nvme-rdma: implement polling queue map
nvme-fabrics: allow user to pass in nr_poll_queues
nvme-fabrics: allow nvmf_connect_io_queue to poll
nvme-core: optionally poll sync commands
block: make request_to_qc_t public
nvme-tcp: fix spelling mistake "attepmpt" -> "attempt"
nvme-tcp: fix endianess annotations
nvmet-tcp: fix endianess annotations
nvme-pci: refactor nvme_poll_irqdisable to make sparse happy
nvme-pci: only set nr_maps to 2 if poll queues are supported
nvmet: use a macro for default error location
nvmet: fix comparison of a u16 with -1
blk-mq: enable IO poll if .nr_queues of type poll > 0
blk-mq: change blk_mq_queue_busy() to blk_mq_queue_inflight()
blk-mq: skip zero-queue maps in blk_mq_map_swqueue
...
Besides the OSD command set that never got traction, the only SCSI
command using bidirectional buffers is XDWRITEREAD in the 10 and 32 byte
variants, which is extremely esoteric and has been removed from the spec
again as of SBC4r15. It probably doesn't make sense to keep the support
code around just for that, so start deprecating the support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
An earlier commit 7fcf2b033b ("blkcg: change blkg reference counting
to use percpu_ref") moved around the release call from blkg_put() to be
a part of the percpu_ref cleanup. Remove the additional unused code
which should have been removed earlier.
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The implementation of blkg_tryget_closest() wasn't super obvious and
became a point of suspicion when debugging [1]. So let's clean it up so
it's obviously not the problem.
Also add missing RCU read locking to bio_clone_blkg_association(), which
got exposed by adding the RCU read lock held check in
blkg_tryget_closest().
[1] https://lore.kernel.org/linux-block/a7e97e4b-0dd8-3a54-23b7-a0f27b17fde8@kernel.dk/
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The Kconfig lexer supports special characters such as '.' and '/' in
the parameter context. In my understanding, the reason is just to
support bare file paths in the source statement.
I do not see a good reason to complicate Kconfig for the room of
ambiguity.
The majority of code already surrounds file paths with double quotes,
and it makes sense since file paths are constant string literals.
Make it treewide consistent now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
sbq_wake_ptr() checks sbq->ws_active to know if it needs to loop
the wait indexes or not. This requires the use of the sbitmap
waitqueue wrappers, but kyber doesn't use those for its domain
token waitqueue handling.
Convert kyber to use the helpers. This fixes a hang with waiting
for domain tokens.
Fixes: 5d2ee7122c ("sbitmap: optimize wakeup check")
Tested-by: Ming Lei <ming.lei@redhat.com>
Reported-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that the the SCSI layer replaced the use of the cluster flag with
segment size limits and the DMA boundary we can remove the cluster flag
from the block layer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
block consumers will need it for polling requests that
are sent with blk_execute_rq_nowait. Also, get rid of
blk_tag_to_qc_t and open-code it instead.
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The queue mapping of type poll only exists when set->map[HCTX_TYPE_POLL].nr_queues
is bigger than zero, so enhance the constraint by checking .nr_queues of type poll
before enabling IO poll.
Otherwise IO race & timeout can be observed when running block/007.
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There's a single user of this function, dm, and dm just wants
to check if IO is inflight, not that it's just allocated.
This fixes a hang with srp/002 in blktests with dm, where it tries
to suspend but waits for inflight IO to finish first. As it checks
for just allocated requests, this fails.
Tested-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
From 7e849dd9cf ("nvme-pci: don't share queue maps"), the mapping
table won't be initialized actually if map->nr_queues is zero, so
we can't use blk_mq_map_queue_type() to retrieve hctx any more.
This way still may cause broken mapping, fix it by skipping zero-queues
maps in blk_mq_map_swqueue().
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The blk-iolatency controller measures the time from rq_qos_throttle() to
rq_qos_done_bio() and attributes this time to the first bio that needs
to create the request. This means if a bio is plug-mergeable or
bio-mergeable, it gets to bypass the blk-iolatency controller.
The recent series [1], to tag all bios w/ blkgs undermined how iolatency
was determining which bios it was charging and should process in
rq_qos_done_bio(). Because all bios are being tagged, this caused the
atomic_t for the struct rq_wait inflight count to underflow and result
in a stall.
This patch adds a new flag BIO_TRACKED to let controllers know that a
bio is going through the rq_qos path. blk-iolatency now checks if this
flag is set to see if it should process the bio in rq_qos_done_bio().
Overloading BLK_QUEUE_ENTERED works, but makes the flag rules confusing.
BIO_THROTTLED was another candidate, but the flag is set for all bios
that have gone through blk-throttle code. Overloading a flag comes with
the burden of making sure that when either implementation changes, a
change in setting rules for one doesn't cause a bug in the other. So
here, we unfortunately opt for adding a new flag.
[1] https://lore.kernel.org/lkml/20181205171039.73066-1-dennis@kernel.org/
Fixes: 5cdf2e3fea ("blkcg: associate blkg when associating a device")
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When a request is added to rq list of sw queue(ctx), the rq may be from
a different type of hctx, especially after multi queue mapping is
introduced.
So when dispach request from sw queue via blk_mq_flush_busy_ctxs() or
blk_mq_dequeue_from_ctx(), one request belonging to other queue type of
hctx can be dispatched to current hctx in case that read queue or poll
queue is enabled.
This patch fixes this issue by introducing per-queue-type list.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Changed by me to not use separately cacheline aligned lists, just
place them all in the same cacheline where we had just the one list
and lock before.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For a zoned block device using mq-deadline, if a write request for a
zone is received while another write was already dispatched for the same
zone, dd_dispatch_request() will return NULL and the newly inserted
write request is kept in the scheduler queue waiting for the ongoing
zone write to complete. With this behavior, when no other request has
been dispatched, rq_list in blk_mq_sched_dispatch_requests() is empty
and blk_mq_sched_mark_restart_hctx() not called. This in turn leads to
__blk_mq_free_request() call of blk_mq_sched_restart() to not run the
queue when the already dispatched write request completes. The newly
dispatched request stays stuck in the scheduler queue until eventually
another request is submitted.
This problem does not affect SCSI disk as the SCSI stack handles queue
restart on request completion. However, this problem is can be triggered
the nullblk driver with zoned mode enabled.
Fix this by always requesting a queue restart in dd_dispatch_request()
if no request was dispatched while WRITE requests are queued.
Fixes: 5700f69178 ("mq-deadline: Introduce zone locking support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Add missing export of blk_mq_sched_restart()
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We should check if a given queue map actually has queues enabled before
dispatching to it. This allows drivers to not initialize optional but
not used map types, which subsequently will allow fixing problems with
queue map rebuilds for that case.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now we only export hctx->type via sysfs, and there isn't such info
in hctx entry under debugfs. We often use debugfs only to diagnose
queue mapping issue, so add the support in debugfs.
Queue mapping becomes a bit more complicated after multiple queue
mapping is supported, we may write blktest to verify if queue mapping
is valid based on blk-mq-debugfs.
Given not necessary to export hctx->type twice, so remove the export
from sysfs.
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Type of each element in queue mapping table is 'unsigned int,
intead of 'struct blk_mq_queue_map)', so fix it.
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This information is helpful to either investigate issues, or understand
wbt's internal behaviour.
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk-mq-debugfs has been proved as very helpful for debug some
tough issues, such as IO hang.
We have seen blk-wbt related IO hang several times, even inside
Red Hat BZ, there is such report not sovled yet, so this patch
adds support debugfs on rq_qos.
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This prevents a HIPRI bio from being submitted through a stacking
driver that does not support polling and thus won't poll for I/O
completion.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace blk_mq_request_issue_directly with blk_mq_try_issue_directly
in blk_insert_cloned_request and kill it as nobody uses it any more.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It is not necessary to issue request directly with bypass 'true'
in blk_mq_sched_insert_requests and handle the non-issued requests
itself. Just set bypass to 'false' and let blk_mq_try_issue_directly
handle them totally. Remove the blk_rq_can_direct_dispatch check,
because blk_mq_try_issue_directly can handle it well.If request is
direct-issued unsuccessfully, insert the reset.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Merge blk_mq_try_issue_directly and __blk_mq_try_issue_directly
into one interface to unify the interfaces to issue requests
directly. The merged interface takes over the requests totally,
it could insert, end or do nothing based on the return value of
.queue_rq and 'bypass' parameter. Then caller needn't any other
handling any more and then code could be cleaned up.
And also the commit c616cbee ( blk-mq: punt failed direct issue
to dispatch list ) always inserts requests to hctx dispatch list
whenever get a BLK_STS_RESOURCE or BLK_STS_DEV_RESOURCE, this is
overkill and will harm the merging. We just need to do that for
the requests that has been through .queue_rq. This patch also
could fix this.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Will be used by nvme-rdma for queue map separation support.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Between v3 [1] and v4 [2] of the blkg association series, the
association point moved from generic_make_request_checks(), which is
called after the request enters the queue, to bio_set_dev(), which is when
the bio is formed before submit_bio(). When the request_queue goes away,
the blkgs supporting the request_queue are destroyed and then the
q->root_blkg is set to %NULL.
This patch adds a %NULL check to blkg_tryget_closest() to prevent the
NPE caused by the above. It also adds a guard to see if the
request_queue is dying when creating a blkg to prevent creating a blkg
for a dead request_queue.
[1] https://lore.kernel.org/lkml/20180911184137.35897-1-dennisszhou@gmail.com/
[2] https://lore.kernel.org/lkml/20181126211946.77067-1-dennis@kernel.org/
Fixes: 5cdf2e3fea ("blkcg: associate blkg when associating a device")
Reported-and-tested-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
null_blk_zoned creation fails if the number of zones specified is equal to or is
smaller than 64 due to a memory allocation failure in blk_alloc_zones(). With
such a small number of zones, the required memory size for all zones descriptors
fits in a single page, and the page order for alloc_pages_node() is zero. Allow
this value in blk_alloc_zones() for the allocation to succeed.
Fixes: bf50545696 "block: Introduce blk_revalidate_disk_zones()"
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We don't need to zero fill the bio if not using kernel allocated pages.
Fixes: f3587d76da ("block: Clear kernel memory before copying to user") # v4.20-rc2
Reported-by: Todd Aiken <taiken@mvtech.ca>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: stable@vger.kernel.org
Cc: Bart Van Assche <bvanassche@acm.org>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The previous patches deleted all the code that needed the second value
returned from part_in_flight - now the kernel only uses the first value.
Consequently, part_in_flight (and blk_mq_in_flight) may be changed so that
it only returns one value.
This patch just refactors the code, there's no functional change.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now when part_round_stats is gone, we can switch to per-cpu in-flight
counters.
We use the local-atomic type local_t, so that if part_inc_in_flight or
part_dec_in_flight is reentrantly called from an interrupt, the value will
be correct.
The other counters could be corrupted due to reentrant interrupt, but the
corruption only results in slight counter skew - the in_flight counter
must be exact, so it needs local_t.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We want to convert to per-cpu in_flight counters.
The function part_round_stats needs the in_flight counter every jiffy, it
would be too costly to sum all the percpu variables every jiffy, so it
must be deleted. part_round_stats is used to calculate two counters -
time_in_queue and io_ticks.
time_in_queue can be calculated without part_round_stats, by adding the
duration of the I/O when the I/O ends (the value is almost as exact as the
previously calculated value, except that time for in-progress I/Os is not
counted).
io_ticks can be approximated by increasing the value when I/O is started
or ended and the jiffies value has changed. If the I/Os take less than a
jiffy, the value is as exact as the previously calculated value. If the
I/Os take more than a jiffy, io_ticks can drift behind the previously
calculated value.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All of part_stat_* and related methods are used with preempt disabled,
so there is no need to pass cpu around to allow of them. Just call
smp_processor_id() as needed.
Suggested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwNpb0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGwGwH/00UHnXfxww3ixxz
zwTVDzptA6SPm6s84yJOWatM5fXhPiAltZaHSYF9lzRzNU71NCq7Frhq3fQUIXKM
OxqDn9nfSTWcjWTk2q5n2keyRV/KIn67YX7UgqFc1bO/mqtVjEgNWaMyblhI+e9E
giu1ZXayHr43jK1cDOmGExZubXUq7Vsc9TOlrd+d2SwIqeEP7TCMrPhnHDwCNvX2
UU5dtANpVzGtHaBcr37wJj+L8kODCc0f+PQ3g2ar5jTHst5SLlHp2u0AMRnUmgdi
VkGx+mu/uk8mtwUqMIMqhplklVoqK6LTeLqsY5Xt32SKruw9UqyJGdphLjW2QP/g
MkmA1lI=
=7kaD
-----END PGP SIGNATURE-----
Merge tag 'v4.20-rc6' into for-4.21/block
Pull in v4.20-rc6 to resolve the conflict in NVMe, but also to get the
two corruption fixes. We're going to be overhauling the direct dispatch
path, and we need to do that on top of the changes we made for that
in mainline.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that we have this common helper, convert io-latency over to use it
as well.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that we have rq_qos_wait() in place, convert wbt_wait() over to
using it with it's specific callbacks.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Originally when I split out the common code from blk-wbt into rq_qos I
left the wbt_wait() where it was and simply copied and modified it
slightly to work for io-latency. However they are both basically the
same thing, and as time has gone on wbt_wait() has ended up much smarter
and kinder than it was when I copied it into io-latency, which means
io-latency has lost out on these improvements.
Since they are the same thing essentially except for a few minor things,
create rq_qos_wait() that replicates what wbt_wait() currently does with
callbacks that can be passed in for the snowflakes to do their own thing
as appropriate.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blkg reference counting now uses percpu_ref rather than atomic_t. Let's
make this consistent with css_tryget. This renames blkg_try_get to
blkg_tryget and now returns a bool rather than the blkg or %NULL.
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Every bio is now associated with a blkg putting blkg_get, blkg_try_get,
and blkg_put on the hot path. Switch over the refcnt in blkg to use
percpu_ref.
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that a bio only holds a blkg reference, so clean up is simply
putting back that reference. Remove bio_disassociate_task() as it just
calls bio_disassociate_blkg() and call the latter directly.
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The previous patch in this series removed carrying around a pointer to
the css in blkg. However, the blkg association logic still relied on
taking a reference on the css to ensure we wouldn't fail in getting a
reference for the blkg.
Here the implicit dependency on the css is removed. The association
continues to rely on the tryget logic walking up the blkg tree. This
streamlines the three ways that association can happen: normal, swap,
and writeback.
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Prior patches ensured that any bio that interacts with a request_queue
is properly associated with a blkg. This makes bio->bi_css unnecessary
as blkg maintains a reference to blkcg already.
This removes the bio field bi_css and transfers corresponding uses to
access via bi_blkg.
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
One of the goals of this series is to remove a separate reference to
the css of the bio. This can and should be accessed via bio_blkcg(). In
this patch, wbc_init_bio() now requires a bio to have a device
associated with it.
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A prior patch in this series added blkg association to bios issued by
cgroups. There are two other paths that we want to attribute work back
to the appropriate cgroup: swap and writeback. Here we modify the way
swap tags bios to include the blkg. Writeback will be tackle in the next
patch.
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bio_issue_init among other things initializes the timestamp for an IO.
Rather than have this logic handled by policies, this consolidates it to
be on the init paths (normal, clone, bounce clone).
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Liu Bo <bo.liu@linux.alibaba.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Previously, blkg association was handled by controller specific code in
blk-throttle and blk-iolatency. However, because a blkg represents a
relationship between a blkcg and a request_queue, it makes sense to keep
the blkg->q and bio->bi_disk->queue consistent.
This patch moves association into the bio_set_dev macro(). This should
cover the majority of cases where the device is set/changed keeping the
two pointers consistent. Fallback code is added to
blkcg_bio_issue_check() to catch any missing paths.
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The next patch changes the macro bio_set_dev() to associate a bio with a
blkg based on the device set. However, dm creates a static bio to be
used as the basis for cloning empty flush bios on creation. The
bio_set_dev() call in alloc_dev() will cause problems with the next
patch adding association to bio_set_dev() because the call is before the
bdev is associated with a gendisk (bd_disk is %NULL). To get around
this, set the device on the static bio every time and use that to clone
to the other bios.
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: Alasdair Kergon <agk@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are 3 ways blkg association can happen: association with the
current css, with the page css (swap), or from the wbc css (writeback).
This patch handles how association is done for the first case where we
are associating bsaed on the current css. If there is already a blkg
associated, the css will be reused and association will be redone as the
request_queue may have changed.
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are several scenarios where blkg_lookup_create() can fail such as
the blkcg dying, request_queue is dying, or simply being OOM. Most
handle this by simply falling back to the q->root_blkg and calling it a
day.
This patch implements the notion of closest blkg. During
blkg_lookup_create(), if it fails to create, return the closest blkg
found or the q->root_blkg. blkg_try_get_closest() is introduced and used
during association so a bio is always attached to a blkg.
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
To know when to create a blkg, the general pattern is to do a
blkg_lookup() and if that fails, lock and do the lookup again, and if
that fails finally create. It doesn't make much sense for everyone who
wants to do creation to write this themselves.
This changes blkg_lookup_create() to do locking and implement this
pattern. The old blkg_lookup_create() is renamed to
__blkg_lookup_create(). If a call site wants to do its own error
handling or already owns the queue lock, they can use
__blkg_lookup_create(). This will be used in upcoming patches.
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The bio_blkcg() function turns out to be inconsistent and consequently
dangerous to use. The first part returns a blkcg where a reference is
owned by the bio meaning it does not need to be rcu protected. However,
the third case, the last line, is problematic:
return css_to_blkcg(task_css(current, io_cgrp_id));
This can race against task migration and the cgroup dying. It is also
semantically different as it must be called rcu protected and is
susceptible to failure when trying to get a reference to it.
This patch adds association ahead of calling bio_blkcg() rather than
after. This makes association a required and explicit step along the
code paths for calling bio_blkcg(). In blk-iolatency, association is
moved above the bio_blkcg() call to ensure it will not return %NULL.
BFQ uses the old bio_blkcg() function, but I do not want to address it
in this series due to the complexity. I have created a private version
documenting the inconsistency and noting not to use it.
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
After the direct dispatch corruption fix, we permanently disallow direct
dispatch of non read/write requests. This works fine off the normal IO
path, as they will be retried like any other failed direct dispatch
request. But for the blk_insert_cloned_request() that only DM uses to
bypass the bottom level scheduler, we always first attempt direct
dispatch. For some types of requests, that's now a permanent failure,
and no amount of retrying will make that succeed. This results in a
livelock.
Instead of making special cases for what we can direct issue, and now
having to deal with DM solving the livelock while still retaining a BUSY
condition feedback loop, always just add a request that has been through
->queue_rq() to the hardware queue dispatch list. These are safe to use
as no merging can take place there. Additionally, if requests do have
prepped data from drivers, we aren't dependent on them not sharing space
in the request structure to safely add them to the IO scheduler lists.
This basically reverts ffe81d4532 and is based on a patch from Ming,
but with the list insert case covered as well.
Fixes: ffe81d4532 ("blk-mq: fix corruption with direct issue")
Cc: stable@vger.kernel.org
Suggested-by: Ming Lei <ming.lei@redhat.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since commit '2d29c9f89fcd ("block, bfq: improve asymmetric scenarios
detection")', if there are process groups with I/O requests waiting for
completion, then BFQ tags the scenario as 'asymmetric'. This detection
is needed for preserving service guarantees (for details, see comments
on the computation * of the variable asymmetric_scenario in the
function bfq_better_to_idle).
Unfortunately, commit '2d29c9f89fcd ("block, bfq: improve asymmetric
scenarios detection")' contains an error exactly in the updating of
the number of groups with I/O requests waiting for completion: if a
group has more than one descendant process, then the above number of
groups, which is renamed from num_active_groups to a more appropriate
num_groups_with_pending_reqs by this commit, may happen to be wrongly
decremented multiple times, namely every time one of the descendant
processes gets all its pending I/O requests completed.
A correct, complete solution should work as follows. Consider a group
that is inactive, i.e., that has no descendant process with pending
I/O inside BFQ queues. Then suppose that num_groups_with_pending_reqs
is still accounting for this group, because the group still has some
descendant process with some I/O request still in
flight. num_groups_with_pending_reqs should be decremented when the
in-flight request of the last descendant process is finally completed
(assuming that nothing else has changed for the group in the meantime,
in terms of composition of the group and active/inactive state of
child groups and processes). To accomplish this, an additional
pending-request counter must be added to entities, and must be
updated correctly.
To avoid this additional field and operations, this commit resorts to
the following tradeoff between simplicity and accuracy: for an
inactive group that is still counted in num_groups_with_pending_reqs,
this commit decrements num_groups_with_pending_reqs when the first
descendant process of the group remains with no request waiting for
completion.
This simplified scheme provides a fix to the unbalanced decrements
introduced by 2d29c9f89f. Since this error was also caused by lack
of comments on this non-trivial issue, this commit also adds related
comments.
Fixes: 2d29c9f89f ("block, bfq: improve asymmetric scenarios detection")
Reported-by: Steven Barrett <steven@liquorix.net>
Tested-by: Steven Barrett <steven@liquorix.net>
Tested-by: Lucjan Lucjanov <lucjan.lucjanov@gmail.com>
Reviewed-by: Federico Motta <federico@willer.it>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we attempt a direct issue to a SCSI device, and it returns BUSY, then
we queue the request up normally. However, the SCSI layer may have
already setup SG tables etc for this particular command. If we later
merge with this request, then the old tables are no longer valid. Once
we issue the IO, we only read/write the original part of the request,
not the new state of it.
This causes data corruption, and is most often noticed with the file
system complaining about the just read data being invalid:
[ 235.934465] EXT4-fs error (device sda1): ext4_iget:4831: inode #7142: comm dpkg-query: bad extra_isize 24937 (inode size 256)
because most of it is garbage...
This doesn't happen from the normal issue path, as we will simply defer
the request to the hardware queue dispatch list if we fail. Once it's on
the dispatch list, we never merge with it.
Fix this from the direct issue path by flagging the request as
REQ_NOMERGE so we don't change the size of it before issue.
See also:
https://bugzilla.kernel.org/show_bug.cgi?id=201685
Tested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 6ce3dd6eec ("blk-mq: issue directly if hw queue isn't busy in case of 'none'")
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If the user did setup polling in the driver we should not require
another know in the block layer to enable it.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This avoids having to have differnet mq_ops for different setups
with or without poll queues.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This was intended to support users like nvme multipath, but is just
getting in the way and adding another indirect call.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Having another indirect all in the fast path doesn't really help
in our post-spectre world. Also having too many queue type is just
going to create confusion, so I'd rather manage them centrally.
Note that the queue type naming and ordering changes a bit - the
first index now is the default queue for everything not explicitly
marked, the optional ones are read and poll queues.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwEZdIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAlQH/19oax2Za3IPqF4X
DM3lal5M6zlUVkoYstqzpbR3MqUwgEnMfvoeMDC6mI9N4/+r2LkV7cRR8HzqQCCS
jDfD69IzRGb52VSeJmbOrkxBWsR1Nn0t4Z3rEeLPxwaOoNpRc8H973MbAQ2FKMpY
S4Y3jIK1dNiRRxdh52NupVkQF+djAUwkBuVk/rrvRJmTDij4la03cuCDAO+Di9lt
GHlVvygKw2SJhDR+z3ArwZNmE0ceCcE6+W7zPHzj2KeWuKrZg22kfUD454f2YEIw
FG0hu9qecgtpYCkLSm2vr4jQzmpsDoyq3ZfwhjGrP4qtvPC3Db3vL3dbQnkzUcJu
JtwhVCE=
=O1q1
-----END PGP SIGNATURE-----
Merge tag 'v4.20-rc5' into for-4.21/block
Pull in v4.20-rc5, solving a conflict we'll otherwise get in aio.c and
also getting the merge fix that went into mainline that users are
hitting testing for-4.21/block and/or for-next.
* tag 'v4.20-rc5': (664 commits)
Linux 4.20-rc5
PCI: Fix incorrect value returned from pcie_get_speed_cap()
MAINTAINERS: Update linux-mips mailing list address
ocfs2: fix potential use after free
mm/khugepaged: fix the xas_create_range() error path
mm/khugepaged: collapse_shmem() do not crash on Compound
mm/khugepaged: collapse_shmem() without freezing new_page
mm/khugepaged: minor reorderings in collapse_shmem()
mm/khugepaged: collapse_shmem() remember to clear holes
mm/khugepaged: fix crashes due to misaccounted holes
mm/khugepaged: collapse_shmem() stop if punched or truncated
mm/huge_memory: fix lockdep complaint on 32-bit i_size_read()
mm/huge_memory: splitting set mapping+index before unfreeze
mm/huge_memory: rename freeze_page() to unmap_page()
initramfs: clean old path before creating a hardlink
kernel/kcov.c: mark funcs in __sanitizer_cov_trace_pc() as notrace
psi: make disabling/enabling easier for vendor kernels
proc: fixup map_files test on arm
debugobjects: avoid recursive calls with kmemleak
userfaultfd: shmem: UFFDIO_COPY: set the page dirty if VM_WRITE is not set
...
We only need the request fields and the end_io time if we have
stats enabled, or if we have a scheduler attached as those may
use it for completion time stats.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
I ran into a bug where after hibernation due to incompatible
backends, the block driver returned BLK_STS_NOTSUPP, with the
current message it's hard to find out what the command flags
were. Adding req->cmd_flags help make the problem easier to
diagnose.
Reviewed-by: Eduardo Valentin <eduval@amazon.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Balbir Singh <sblbir@amzn.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Even if we have no waiters on any of the sbitmap_queue wait states, we
still have to loop every entry to check. We do this for every IO, so
the cost adds up.
Shift a bit of the cost to the slow path, when we actually have waiters.
Wrap prepare_to_wait_exclusive() and finish_wait(), so we can maintain
an internal count of how many are currently active. Then we can simply
check this count in sbq_wake_ptr() and not have to loop if we don't
have any sleepers.
Convert the two users of sbitmap with waiting, blk-mq-tag and iSCSI.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we have that hook, we know the driver handles bd->last == true in
a smart fashion. If it does, even for multiple hardware queues, it's
a good idea to flush batches of requests to the device, if we have
batches of requests from the submitter.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we are issuing a list of requests, we know if we're at the last one.
If we fail issuing, ensure that we call ->commits_rqs() to flush any
potential previous requests.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk-mq passes information to the hardware about any given request being
the last that we will issue in this sequence. The point is that hardware
can defer costly doorbell type writes to the last request. But if we run
into errors issuing a sequence of requests, we may never send the request
with bd->last == true set. For that case, we need a hook that tells the
hardware that nothing else is coming right now.
For failures returned by the drivers ->queue_rq() hook, the driver is
responsible for flushing pending requests, if it uses bd->last to
optimize that part. This works like before, no changes there.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Only do it if we have requests for multiple queues in the same
plug.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
I recently found some code which called blk_mq_free_map_and_requests()
with a NULL set->tags pointer. I fixed the caller, but it seems like a
good idea to add a NULL check here as well. Now we can call:
blk_mq_free_tag_set(set);
blk_mq_free_tag_set(set);
twice in a row and it's harmless.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Give a interface to adjust io timeout(ms) by device.
Signed-off-by: Weiping Zhang <zhangweiping@didiglobal.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We recently got a stack by syzkaller like this:
BUG: sleeping function called from invalid context at mm/slab.h:361
in_atomic(): 1, irqs_disabled(): 0, pid: 6644, name: blkid
INFO: lockdep is turned off.
CPU: 1 PID: 6644 Comm: blkid Not tainted 4.4.163-514.55.6.9.x86_64+ #76
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
0000000000000000 5ba6a6b879e50c00 ffff8801f6b07b10 ffffffff81cb2194
0000000041b58ab3 ffffffff833c7745 ffffffff81cb2080 5ba6a6b879e50c00
0000000000000000 0000000000000001 0000000000000004 0000000000000000
Call Trace:
<IRQ> [<ffffffff81cb2194>] __dump_stack lib/dump_stack.c:15 [inline]
<IRQ> [<ffffffff81cb2194>] dump_stack+0x114/0x1a0 lib/dump_stack.c:51
[<ffffffff8129a981>] ___might_sleep+0x291/0x490 kernel/sched/core.c:7675
[<ffffffff8129ac33>] __might_sleep+0xb3/0x270 kernel/sched/core.c:7637
[<ffffffff81794c13>] slab_pre_alloc_hook mm/slab.h:361 [inline]
[<ffffffff81794c13>] slab_alloc_node mm/slub.c:2610 [inline]
[<ffffffff81794c13>] slab_alloc mm/slub.c:2692 [inline]
[<ffffffff81794c13>] kmem_cache_alloc_trace+0x2c3/0x5c0 mm/slub.c:2709
[<ffffffff81cbe9a7>] kmalloc include/linux/slab.h:479 [inline]
[<ffffffff81cbe9a7>] kzalloc include/linux/slab.h:623 [inline]
[<ffffffff81cbe9a7>] kobject_uevent_env+0x2c7/0x1150 lib/kobject_uevent.c:227
[<ffffffff81cbf84f>] kobject_uevent+0x1f/0x30 lib/kobject_uevent.c:374
[<ffffffff81cbb5b9>] kobject_cleanup lib/kobject.c:633 [inline]
[<ffffffff81cbb5b9>] kobject_release+0x229/0x440 lib/kobject.c:675
[<ffffffff81cbb0a2>] kref_sub include/linux/kref.h:73 [inline]
[<ffffffff81cbb0a2>] kref_put include/linux/kref.h:98 [inline]
[<ffffffff81cbb0a2>] kobject_put+0x72/0xd0 lib/kobject.c:692
[<ffffffff8216f095>] put_device+0x25/0x30 drivers/base/core.c:1237
[<ffffffff81c4cc34>] delete_partition_rcu_cb+0x1d4/0x2f0 block/partition-generic.c:232
[<ffffffff813c08bc>] __rcu_reclaim kernel/rcu/rcu.h:118 [inline]
[<ffffffff813c08bc>] rcu_do_batch kernel/rcu/tree.c:2705 [inline]
[<ffffffff813c08bc>] invoke_rcu_callbacks kernel/rcu/tree.c:2973 [inline]
[<ffffffff813c08bc>] __rcu_process_callbacks kernel/rcu/tree.c:2940 [inline]
[<ffffffff813c08bc>] rcu_process_callbacks+0x59c/0x1c70 kernel/rcu/tree.c:2957
[<ffffffff8120f509>] __do_softirq+0x299/0xe20 kernel/softirq.c:273
[<ffffffff81210496>] invoke_softirq kernel/softirq.c:350 [inline]
[<ffffffff81210496>] irq_exit+0x216/0x2c0 kernel/softirq.c:391
[<ffffffff82c2cd7b>] exiting_irq arch/x86/include/asm/apic.h:652 [inline]
[<ffffffff82c2cd7b>] smp_apic_timer_interrupt+0x8b/0xc0 arch/x86/kernel/apic/apic.c:926
[<ffffffff82c2bc25>] apic_timer_interrupt+0xa5/0xb0 arch/x86/entry/entry_64.S:746
<EOI> [<ffffffff814cbf40>] ? audit_kill_trees+0x180/0x180
[<ffffffff8187d2f7>] fd_install+0x57/0x80 fs/file.c:626
[<ffffffff8180989e>] do_sys_open+0x45e/0x550 fs/open.c:1043
[<ffffffff818099c2>] SYSC_open fs/open.c:1055 [inline]
[<ffffffff818099c2>] SyS_open+0x32/0x40 fs/open.c:1050
[<ffffffff82c299e1>] entry_SYSCALL_64_fastpath+0x1e/0x9a
In softirq context, we call rcu callback function delete_partition_rcu_cb(),
which may allocate memory by kzalloc with GFP_KERNEL flag. If the
allocation cannot be satisfied, it may sleep. However, That is not allowed
in softirq contex.
Although we found this problem on linux 4.4, the latest kernel version
seems to have this problem as well. And it is very similar to the
previous one:
https://lkml.org/lkml/2018/7/9/391
Fix it by using RCU workqueue, which allows sleep.
Reviewed-by: Paul E. McKenney <paulmck@linux.ibm.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we yank a 'same_queue_rq' request off the plug list, we should
also decrement the cached request count.
Fixes: 5f0ed774ed ("block: sum requests in the plug structure")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
