iMX6 devices suffer from an errata (ERR005174) where the audio FIFO can
be emptied while it is partially full, resulting in misalignment of the
audio samples.
To prevent this, the errata workaround recommends writing N as zero
until the audio FIFO has been loaded by DMA. Writing N=0 prevents the
HDMI bridge from reading from the audio FIFO, effectively disabling
audio.
This means we need to provide the audio driver with a pair of functions
to enable/disable audio. These are dw_hdmi_audio_enable() and
dw_hdmi_audio_disable().
A spinlock is introduced to ensure that setting the CTS/N values can't
race, ensuring that the audio driver calling the enable/disable
functions (which are called in an atomic context) can't race with a
modeset.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce dw_hdmi_set_sample_rate(), which allows us to configure the
audio sample rate, setting the CTS/N values appropriately.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the struct hdmi_vmode mhsyncpolarity/mvsyncpolarity/minterlaced
members, which are only used within a single function. We can directly
reference the appropriate mode->flags instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When a YCBCR format is selected, we can merely copy the colorimetry
information directly as we use the same definitions for both the
unpacked AVI info frame and the hdmi_data_info structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clean up hdmi_set_clk_regenerator() by allowing it to take the audio
sample rate and ratio directly, rather than hiding it inside the
function. Raise the unsupported pixel clock/sample rate message from
debug to error level as this results in audio not working correctly.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phy configuration is dependent on the SoC, and we look up values for
some of the registers in SoC specific data. However, we had partially
programmed the phy before we had successfully looked up the clock rate.
Also, we were only checking that we had a valid configuration for the
currctrl register.
Move all these lookups to the start of this function instead, so we can
check that all lookups were successful before beginning to program the
phy.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phy comments in dw_hdmi.c applied to the iMX6 version. Move these
comments to the iMX6 dw_hdmi-imx data along side the data.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a function to find the start of the SADs in the ELD. This
complements the helper to retrieve the SAD count.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a helper to create the IEC958 channel status from an ALSA
snd_pcm_runtime structure, taking account of the sample rate and
sample size.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a helper for the EDID like data structure, which is typically passed
from a HDMI adapter to its associated audio driver. This informs the
audio driver of the capabilities of the attached HDMI sink.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AMD CPUs don't reinitialize the SS descriptor on SYSRET, so SYSRET with
SS == 0 results in an invalid usermode state in which SS is apparently
equal to __USER_DS but causes #SS if used.
Work around the issue by setting SS to __KERNEL_DS __switch_to, thus
ensuring that SYSRET never happens with SS set to NULL.
This was exposed by a recent vDSO cleanup.
Fixes: e7d6eefaaa x86/vdso32/syscall.S: Do not load __USER32_DS to %ss
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull intel drm fixes from Dave Airlie.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: vlv: fix save/restore of GFX_MAX_REQ_COUNT reg
drm/i915: Workaround to avoid lite restore with HEAD==TAIL
drm/i915: cope with large i2c transfers
Pull intel iommu updates from David Woodhouse:
"This lays a little of the groundwork for upcoming Shared Virtual
Memory support — fixing some bogus #defines for capability bits and
adding the new ones, and starting to use the new wider page tables
where we can, in anticipation of actually filling in the new fields
therein.
It also allows graphics devices to be assigned to VM guests again.
This got broken in 3.17 by disallowing assignment of RMRR-afflicted
devices. Like USB, we do understand why there's an RMRR for graphics
devices — and unlike USB, it's actually sane. So we can make an
exception for graphics devices, just as we do USB controllers.
Finally, tone down the warning about the X2APIC_OPT_OUT bit, due to
persistent requests. X2APIC_OPT_OUT was added to the spec as a nasty
hack to allow broken BIOSes to forbid us from using X2APIC when they
do stupid and invasive things and would break if we did.
Someone noticed that since Windows doesn't have full IOMMU support for
DMA protection, setting the X2APIC_OPT_OUT bit made Windows avoid
initialising the IOMMU on the graphics unit altogether.
This means that it would be available for use in "driver mode", where
the IOMMU registers are made available through a BAR of the graphics
device and the graphics driver can do SVM all for itself.
So they started setting the X2APIC_OPT_OUT bit on *all* platforms with
SVM capabilities. And even the platforms which *might*, if the
planets had been aligned correctly, possibly have had SVM capability
but which in practice actually don't"
* git://git.infradead.org/intel-iommu:
iommu/vt-d: support extended root and context entries
iommu/vt-d: Add new extended capabilities from v2.3 VT-d specification
iommu/vt-d: Allow RMRR on graphics devices too
iommu/vt-d: Print x2apic opt out info instead of printing a warning
iommu/vt-d: kill bogus ecap_niotlb_iunits()
Pull i2c fixes from Wolfram Sang:
"This has a mixture of merge window cleanups and bugfixes"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: st: add include for pinctrl
i2c: mux: use proper dev when removing "channel-X" symlinks
i2c: digicolor: remove duplicate include
i2c: Mark adapter devices with pm_runtime_no_callbacks
i2c: pca-platform: fix broken email address
i2c: mxs: fix broken email address
i2c: rk3x: report number of messages transmitted
Pull btrfs fixes from Chris Mason:
"Filipe hit two problems in my block group cache patches. We finalized
the fixes last week and ran through more tests"
* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: prevent list corruption during free space cache processing
Btrfs: fix inode cache writeout
three fixes for i915.
* tag 'drm-intel-next-fixes-2015-04-25' of git://anongit.freedesktop.org/drm-intel:
drm/i915: vlv: fix save/restore of GFX_MAX_REQ_COUNT reg
drm/i915: Workaround to avoid lite restore with HEAD==TAIL
drm/i915: cope with large i2c transfers
Highlights include:
Stable patches:
- Fix a regression in /proc/self/mountstats
- Fix the pNFS flexfiles O_DIRECT support
- Fix high load average due to callback thread sleeping
Bugfixes:
- Various patches to fix the pNFS layoutcommit support
- Do not cache pNFS deviceids unless server notifications are enabled
- Fix a SUNRPC transport reconnection regression
- make debugfs file creation failure non-fatal in SUNRPC
- Another fix for circular directory warnings on NFSv4 "junctioned" mountpoints
- Fix locking around NFSv4.2 fallocate() support
- Truncating NFSv4 file opens should also sync O_DIRECT writes
- Prevent infinite loop in rpcrdma_ep_create()
Features:
- Various improvements to the RDMA transport code's handling of memory
registration
- Various code cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=j5dP
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.1-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Another set of mainly bugfixes and a couple of cleanups. No new
functionality in this round.
Highlights include:
Stable patches:
- Fix a regression in /proc/self/mountstats
- Fix the pNFS flexfiles O_DIRECT support
- Fix high load average due to callback thread sleeping
Bugfixes:
- Various patches to fix the pNFS layoutcommit support
- Do not cache pNFS deviceids unless server notifications are enabled
- Fix a SUNRPC transport reconnection regression
- make debugfs file creation failure non-fatal in SUNRPC
- Another fix for circular directory warnings on NFSv4 "junctioned"
mountpoints
- Fix locking around NFSv4.2 fallocate() support
- Truncating NFSv4 file opens should also sync O_DIRECT writes
- Prevent infinite loop in rpcrdma_ep_create()
Features:
- Various improvements to the RDMA transport code's handling of
memory registration
- Various code cleanups"
* tag 'nfs-for-4.1-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (55 commits)
fs/nfs: fix new compiler warning about boolean in switch
nfs: Remove unneeded casts in nfs
NFS: Don't attempt to decode missing directory entries
Revert "nfs: replace nfs_add_stats with nfs_inc_stats when add one"
NFS: Rename idmap.c to nfs4idmap.c
NFS: Move nfs_idmap.h into fs/nfs/
NFS: Remove CONFIG_NFS_V4 checks from nfs_idmap.h
NFS: Add a stub for GETDEVICELIST
nfs: remove WARN_ON_ONCE from nfs_direct_good_bytes
nfs: fix DIO good bytes calculation
nfs: Fetch MOUNTED_ON_FILEID when updating an inode
sunrpc: make debugfs file creation failure non-fatal
nfs: fix high load average due to callback thread sleeping
NFS: Reduce time spent holding the i_mutex during fallocate()
NFS: Don't zap caches on fallocate()
xprtrdma: Make rpcrdma_{un}map_one() into inline functions
xprtrdma: Handle non-SEND completions via a callout
xprtrdma: Add "open" memreg op
xprtrdma: Add "destroy MRs" memreg op
xprtrdma: Add "reset MRs" memreg op
...
Pull fourth vfs update from Al Viro:
"d_inode() annotations from David Howells (sat in for-next since before
the beginning of merge window) + four assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RCU pathwalk breakage when running into a symlink overmounting something
fix I_DIO_WAKEUP definition
direct-io: only inc/dec inode->i_dio_count for file systems
fs/9p: fix readdir()
VFS: assorted d_backing_inode() annotations
VFS: fs/inode.c helpers: d_inode() annotations
VFS: fs/cachefiles: d_backing_inode() annotations
VFS: fs library helpers: d_inode() annotations
VFS: assorted weird filesystems: d_inode() annotations
VFS: normal filesystems (and lustre): d_inode() annotations
VFS: security/: d_inode() annotations
VFS: security/: d_backing_inode() annotations
VFS: net/: d_inode() annotations
VFS: net/unix: d_backing_inode() annotations
VFS: kernel/: d_inode() annotations
VFS: audit: d_backing_inode() annotations
VFS: Fix up some ->d_inode accesses in the chelsio driver
VFS: Cachefiles should perform fs modifications on the top layer only
VFS: AF_UNIX sockets should call mknod on the top layer only
- Fix a build warning in the intel_pstate driver showing up in non-SMP
builds (Borislav Petkov).
- Change one of the intel_pstate's P-state selection parameters for
Baytrail and Cherrytrail CPUs to significantly improve performance
at the cost of a small increase in energy consumption (Kristen
Carlson Accardi).
- Fix a NULL pointer dereference in the ACPI EC driver due to an unsafe
list walk in the query handler removal routine (Chris Bainbridge).
- Get rid of a false-positive lockdep warning in the ACPI container
hot-remove code (Rafael J Wysocki).
- Prevent the ACPI device enumeration code from creating device
objects of a wrong type in some cases (Rafael J Wysocki).
- Add Skylake processors support to the Intel RAPL power capping
driver (Brian Bian).
- Drop the stale MAINTAINERS entry for the ACPI dock driver that is
regarded as part of the ACPI core and maintained along with it now
(Chao Yu).
- Fix cpupower tool breakage caused by a library API change in libpci
3.3.0 (Lucas Stach).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=0bKD
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"These are fixes mostly (intel_pstate, ACPI core, ACPI EC driver,
cpupower tool), a new CPU ID for the Intel RAPL driver and one
intel_pstate driver improvement that didn't make it to my previous
pull requests due to timing.
Specifics:
- Fix a build warning in the intel_pstate driver showing up in
non-SMP builds (Borislav Petkov)
- Change one of the intel_pstate's P-state selection parameters for
Baytrail and Cherrytrail CPUs to significantly improve performance
at the cost of a small increase in energy consumption (Kristen
Carlson Accardi)
- Fix a NULL pointer dereference in the ACPI EC driver due to an
unsafe list walk in the query handler removal routine (Chris
Bainbridge)
- Get rid of a false-positive lockdep warning in the ACPI container
hot-remove code (Rafael J Wysocki)
- Prevent the ACPI device enumeration code from creating device
objects of a wrong type in some cases (Rafael J Wysocki)
- Add Skylake processors support to the Intel RAPL power capping
driver (Brian Bian)
- Drop the stale MAINTAINERS entry for the ACPI dock driver that is
regarded as part of the ACPI core and maintained along with it now
(Chao Yu)
- Fix cpupower tool breakage caused by a library API change in libpci
3.3.0 (Lucas Stach)"
* tag 'pm+acpi-4.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / scan: Add a scan handler for PRP0001
ACPI / scan: Annotate physical_node_lock in acpi_scan_is_offline()
ACPI / EC: fix NULL pointer dereference in acpi_ec_remove_query_handler()
MAINTAINERS: remove maintainship entry of docking station driver
powercap / RAPL: Add support for Intel Skylake processors
cpufreq: intel_pstate: Fix an annoying !CONFIG_SMP warning
intel_pstate: Change the setpoint for Atom params
cpupower: fix breakage from libpci API change
Pull crypto fixes from Herbert Xu:
"This push fixes a build problem with img-hash under non-standard
configurations and a serious regression with sha512_ssse3 which can
lead to boot failures"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: img-hash - CRYPTO_DEV_IMGTEC_HASH should depend on HAS_DMA
crypto: x86/sha512_ssse3 - fixup for asm function prototype change
dell-laptop: Add support for keyboard backlight.
toshiba_acpi: Adaptive keyboard, hotkey, USB sleep and charge,
and backlight updates. Update sysfs documentation.
toshiba_bluetooth: Fix enabling/disabling loop on recent devices
apple-gmux: lock iGP IO to protect from vgaarb changes
other: Fix typos, clear gcc warnings, clarify pr_* messages,
correct return types, update MAINTAINERS.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVOzXzAAoJEKbMaAwKp364yjQH/3RJQAiemygVKTv8npk6am4W
6NjoQHwFbvbHnea1DsMBI66DgvDFuXBi04/eKoFtZiSQdt3LOWyF04VY7yPdGKT/
0yIgxMonhLk/lbBiU1PmyAsloOI4mG3zylOO+zJv66LeW0q2vjlLK7xE7AJn0dVU
hRn+Wl0YCjPzEEB4uZpKY6V0+7ys0Odxd2MeYu7pcs5DQzbvzeo4JRwUL4VtNiX9
M1I4ucBRA9jjnuNDzr4d9WtttorOOymoBYy3KFE+2QzDr5chhXTbWp6mRzwnYRvy
siOEPLzeR9jTSB4U514I1CktsCmYxvGnrGcNj1IgiY8VFujoh9j6Ndh339f8064=
=O+n4
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.1-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"This series includes significant updates to the toshiba_acpi driver
and the reintroduction of the dell-laptop keyboard backlight additions
I had to revert previously. Also included are various fixes for
typos, warnings, correctness, and minor bugs.
Specifics:
dell-laptop:
- add support for keyboard backlight.
toshiba_acpi:
- adaptive keyboard, hotkey, USB sleep and charge, and backlight
updates. Update sysfs documentation.
toshiba_bluetooth:
- fix enabling/disabling loop on recent devices
apple-gmux:
- lock iGP IO to protect from vgaarb changes
other:
- Fix typos, clear gcc warnings, clarify pr_* messages, correct
return types, update MAINTAINERS"
* tag 'platform-drivers-x86-v4.1-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (25 commits)
toshiba_acpi: Do not register vendor backlight when acpi_video bl is available
MAINTAINERS: Add me on list of Dell laptop drivers
platform: x86: dell-laptop: Add support for keyboard backlight
Documentation/ABI: Update sysfs-driver-toshiba_acpi entry
toshiba_acpi: Fix pr_* messages from USB Sleep Functions
toshiba_acpi: Update and fix USB Sleep and Charge modes
wmi: Use bool function return values of true/false not 1/0
toshiba_bluetooth: Fix enabling/disabling loop on recent devices
toshiba_bluetooth: Clean up *_add function and disable BT device at removal
toshiba_bluetooth: Add three new functions to the driver
toshiba_acpi: Fix the enabling of the Special Functions
toshiba_acpi: Use the Hotkey Event Type function for keymap choosing
toshiba_acpi: Add Hotkey Event Type function and definitions
x86/wmi: delete unused wmi_data_lock mutex causing gcc warning
apple-gmux: lock iGP IO to protect from vgaarb changes
MAINTAINERS: Add missing Toshiba devices and add myself as maintainer
toshiba_acpi: Update events in toshiba_acpi_notify
intel-oaktrail: Fix trivial typo in comment
thinkpad_acpi: off by one in adaptive_keyboard_hotkey_notify_hotkey()
thinkpad_acpi: signedness bugs getting current_mode
...
Here's a set of updates to the Chrome OS platform drivers for this merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can make your
own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The laptop driver
is trying to be smart and not instantiate the devices that don't answer to
probe. For the trackpad that can come up in two modes (bootloader or regular),
this gets complicated since the driver already knows how to handle the two
modes including the actual addresses used. So now the laptop driver needs to
know more too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few bugfixes
from him, kbuild and myself.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NVa4
-----END PGP SIGNATURE-----
Merge tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform updates from Olof Johansson:
"Here's a set of updates to the Chrome OS platform drivers for this
merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can
make your own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The
laptop driver is trying to be smart and not instantiate the devices
that don't answer to probe. For the trackpad that can come up in
two modes (bootloader or regular), this gets complicated since the
driver already knows how to handle the two modes including the
actual addresses used. So now the laptop driver needs to know more
too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few
bugfixes from him, kbuild and myself"
* tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
platform/chrome: chromeos_laptop - instantiate Atmel at primary address
platform/chrome: cros_ec_lpc - Depend on X86 || COMPILE_TEST
platform/chrome: cros_ec_lpc - Include linux/io.h header file
platform/chrome: fix platform_no_drv_owner.cocci warnings
platform/chrome: cros_ec_lightbar - fix duplicate const warning
platform/chrome: cros_ec_dev - fix Unknown escape '%' warning
platform/chrome: Expose Chrome OS Lightbar to users
platform/chrome: Create sysfs attributes for the ChromeOS EC
mfd: cros_ec: Instantiate ChromeOS EC character device
platform/chrome: Add Chrome OS EC userspace device interface
platform/chrome: Add cros_ec_lpc driver for x86 devices
mfd: cros_ec: Add char dev and virtual dev pointers
mfd: cros_ec: Use fixed size arrays to transfer data with the EC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlU70nMACgkQ31LbvUHyf1cYgwCfSmPhyLFmr0pGM/BxsVY7K1v6
PaEAn2+7xfZV38E6hwrGMrT42ZvKyL6r
=LHQU
-----END PGP SIGNATURE-----
Merge tag 'cris-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull arch/cris updates from Jesper Nilsson:
"Some much needed love for the CRIS-port.
There's a bunch of changes this time, giving the CRISv32 port a bit of
modern makeover with device-tree, irq domain and gpiolib support, and
more switchover to generic frameworks.
Some small fixes and removal of the theoretical SMP support brings up
the rear"
* tag 'cris-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
cris: fix integer overflow in ELF_ET_DYN_BASE
CRISv32: use GENERIC_SCHED_CLOCK
CRISv32: use MMIO clocksource
CRISv32: use generic clockevents
CRIS: use generic headers via Kbuild
CRIS: use generic cmpxchg.h
CRIS: use generic atomic.h
CRIS: use generic atomic bitops
CRISv10: remove redundant macros from system.h
CRIS: remove SMP code
CRISv32: don't enable irqs in INIT_THREAD
CRISv32: handle multiple signals
CRISv32: prevent bogus restarts on sigreturn
CRISv32: don't attempt syscall restart on irq exit
Add binding documentation for CRIS
CRIS: add Axis 88 board device tree
CRISv32: add device tree support
CRISv32: add irq domains support
CRIS: enable GPIOLIB
- Fix for mm_dec_nr_pmds() from Scott.
- Fixes for oopses seen with KVM + THP from Aneesh.
- Build fixes from Aneesh & Shreyas.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6yQx
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
- fix for mm_dec_nr_pmds() from Scott.
- fixes for oopses seen with KVM + THP from Aneesh.
- build fixes from Aneesh & Shreyas.
* tag 'powerpc-4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/mm: Fix build error with CONFIG_PPC_TRANSACTIONAL_MEM disabled
powerpc/kvm: Fix ppc64_defconfig + PPC_POWERNV=n build error
powerpc/mm/thp: Return pte address if we find trans_splitting.
powerpc/mm/thp: Make page table walk safe against thp split/collapse
KVM: PPC: Remove page table walk helpers
KVM: PPC: Use READ_ONCE when dereferencing pte_t pointer
powerpc/hugetlb: Call mm_dec_nr_pmds() in hugetlb_free_pmd_range()
Book3S HV only (debugging aids, minor performance improvements and some
cleanups). But there are also bug fixes and small cleanups for ARM,
x86 and s390.
The task_migration_notifier revert and real fix is still pending review,
but I'll send it as soon as possible after -rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJVOONLAAoJEL/70l94x66DbsMIAIpZPsaqgXOC1sDEiZuYay+6
rD4n4id7j8hIAzcf3AlZdyf5XgLlr6I1Zyt62s1WcoRq/CCnL7k9EljzSmw31WFX
P2y7/J0iBdkn0et+PpoNThfL2GsgTqNRCLOOQlKgEQwMP9Dlw5fnUbtC1UchOzTg
eAMeBIpYwufkWkXhdMw4PAD4lJ9WxUZ1eXHEBRzJb0o0ZxAATJ1tPZGrFJzoUOSM
WsVNTuBsNd7upT02kQdvA1TUo/OPjseTOEoksHHwfcORt6bc5qvpctL3jYfcr7sk
/L6sIhYGVNkjkuredjlKGLfT2DDJjSEdJb1k2pWrDRsY76dmottQubAE9J9cDTk=
=OAi2
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull second batch of KVM changes from Paolo Bonzini:
"This mostly includes the PPC changes for 4.1, which this time cover
Book3S HV only (debugging aids, minor performance improvements and
some cleanups). But there are also bug fixes and small cleanups for
ARM, x86 and s390.
The task_migration_notifier revert and real fix is still pending
review, but I'll send it as soon as possible after -rc1"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (29 commits)
KVM: arm/arm64: check IRQ number on userland injection
KVM: arm: irqfd: fix value returned by kvm_irq_map_gsi
KVM: VMX: Preserve host CR4.MCE value while in guest mode.
KVM: PPC: Book3S HV: Use msgsnd for signalling threads on POWER8
KVM: PPC: Book3S HV: Translate kvmhv_commence_exit to C
KVM: PPC: Book3S HV: Streamline guest entry and exit
KVM: PPC: Book3S HV: Use bitmap of active threads rather than count
KVM: PPC: Book3S HV: Use decrementer to wake napping threads
KVM: PPC: Book3S HV: Don't wake thread with no vcpu on guest IPI
KVM: PPC: Book3S HV: Get rid of vcore nap_count and n_woken
KVM: PPC: Book3S HV: Move vcore preemption point up into kvmppc_run_vcpu
KVM: PPC: Book3S HV: Minor cleanups
KVM: PPC: Book3S HV: Simplify handling of VCPUs that need a VPA update
KVM: PPC: Book3S HV: Accumulate timing information for real-mode code
KVM: PPC: Book3S HV: Create debugfs file for each guest's HPT
KVM: PPC: Book3S HV: Add ICP real mode counters
KVM: PPC: Book3S HV: Move virtual mode ICP functions to real-mode
KVM: PPC: Book3S HV: Convert ICS mutex lock to spin lock
KVM: PPC: Book3S HV: Add guest->host real mode completion counters
KVM: PPC: Book3S HV: Add helpers for lock/unlock hpte
...
The new Atmel MXT driver expects i2c client's address contain the
primary (main address) of the chip, and calculates the expected
bootloader address form the primary address. Unfortunately chrome_laptop
does probe the devices and if touchpad (or touchscreen, or both) comes
up in bootloader mode the i2c device gets instantiated with the
bootloader address which confuses the driver.
To work around this issue let's probe the primary address first. If the
device is not detected at the primary address we'll probe alternative
addresses as "dummy" devices. If any of them are found, destroy the
dummy client and instantiate client with proper name at primary address
still.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Calling unlazy_walk() in walk_component() and do_last() when we find
a symlink that needs to be followed doesn't acquire a reference to vfsmount.
That's fine when the symlink is on the same vfsmount as the parent directory
(which is almost always the case), but it's not always true - one _can_
manage to bind a symlink on top of something. And in such cases we end up
with excessive mntput().
Cc: stable@vger.kernel.org # since 2.6.39
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
I_DIO_WAKEUP is never directly used, but fix it up anyway.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
do_blockdev_direct_IO() increments and decrements the inode
->i_dio_count for each IO operation. It does this to protect against
truncate of a file. Block devices don't need this sort of protection.
For a capable multiqueue setup, this atomic int is the only shared
state between applications accessing the device for O_DIRECT, and it
presents a scaling wall for that. In my testing, as much as 30% of
system time is spent incrementing and decrementing this value. A mixed
read/write workload improved from ~2.5M IOPS to ~9.6M IOPS, with
better latencies too. Before:
clat percentiles (usec):
| 1.00th=[ 33], 5.00th=[ 34], 10.00th=[ 34], 20.00th=[ 34],
| 30.00th=[ 34], 40.00th=[ 34], 50.00th=[ 35], 60.00th=[ 35],
| 70.00th=[ 35], 80.00th=[ 35], 90.00th=[ 37], 95.00th=[ 80],
| 99.00th=[ 98], 99.50th=[ 151], 99.90th=[ 155], 99.95th=[ 155],
| 99.99th=[ 165]
After:
clat percentiles (usec):
| 1.00th=[ 95], 5.00th=[ 108], 10.00th=[ 129], 20.00th=[ 149],
| 30.00th=[ 155], 40.00th=[ 161], 50.00th=[ 167], 60.00th=[ 171],
| 70.00th=[ 177], 80.00th=[ 185], 90.00th=[ 201], 95.00th=[ 270],
| 99.00th=[ 390], 99.50th=[ 398], 99.90th=[ 418], 99.95th=[ 422],
| 99.99th=[ 438]
In other setups, Robert Elliott reported seeing good performance
improvements:
https://lkml.org/lkml/2015/4/3/557
The more applications accessing the device, the worse it gets.
Add a new direct-io flags, DIO_SKIP_DIO_COUNT, which tells
do_blockdev_direct_IO() that it need not worry about incrementing
or decrementing the inode i_dio_count for this caller.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Elliott, Robert (Server Storage) <elliott@hp.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro's IOV changes broke 9p readdir() because the new code
didn't abort the read when it returned nothing. The original
code checked if the combined error/length was <= 0 but in the
new code that accidentally got changed to just an error check.
Add back the return from the function when nothing is read.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Fixes: e1200fe68f ("9p: switch p9_client_read() to passing struct iov_iter *")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
__btrfs_write_out_cache is holding the ctl->tree_lock while it prepares
a list of bitmaps to record in the free space cache. It was dropping
the lock while it worked on other components, which made a window for
free_bitmap() to free the bitmap struct without removing it from the
list.
This changes things to hold the lock the whole time, and also makes sure
we hold the lock during enospc cleanup.
Reported-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
commit a39f46df33 ("toshiba_acpi: Fix regression caused by backlight extra
check code") causes the backlight to no longer work on the Toshiba Z30,
reverting that commit fixes this but restores the original issue fixed
by that commit.
Looking at the toshiba_acpi backlight code for a fix for this I noticed that
the toshiba code is the only code under platform/x86 which unconditionally
registers a vendor acpi backlight interface, without checking for acpi_video
backlight support first.
This commit adds the necessary checks bringing toshiba_acpi in line with the
other drivers, and fixing the Z30 regression without needing to revert the
commit causing it.
Chances are that there will be some Toshiba models which have a non working
acpi-video implementation while the toshiba vendor backlight interface does
work, this commit adds an empty dmi_id table where such systems can be added,
this is identical to how other drivers handle such systems.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1206036
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=86521
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-and-tested-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Here are a few fixes that have been pending since the previous pull
request: a regression fix for HD-audio multiple SPDIF / HDMI devices,
several ALC256 codec fixes, a couple of i915 HDMI audio fixes, and
various small fixes.
Nothing exciting, just boring, but things good to have.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=TICa
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a few fixes that have been pending since the previous pull
request: a regression fix for HD-audio multiple SPDIF / HDMI devices,
several ALC256 codec fixes, a couple of i915 HDMI audio fixes, and
various small fixes.
Nothing exciting, just boring, but things good to have"
* tag 'sound-fix-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - fix headset mic detection problem for one more machine
ALSA: hda/realtek - Fix Headphone Mic doesn't recording for ALC256
ALSA: hda - fix "num_steps = 0" error on ALC256
ALSA: usb-audio: Fix audio output on Roland SC-D70 sound module
ALSA: hda - add AZX_DCAPS_I915_POWERWELL to Baytrail
ALSA: hda - only sync BCLK to the display clock for Haswell & Broadwell
ALSA: hda - Mute headphone pin on suspend on XPS13 9333
sound/oss: fix deadlock in sequencer_ioctl(SNDCTL_SEQ_OUTOFBAND)
ALSA: asound.h - use SNDRV_CTL_ELEM_ID_NAME_MAXLEN
ALSA: hda - potential (but unlikely) uninitialized variable
ALSA: hda - Fix regression for slave SPDIF setups
ALSA: intel8x0: Check pci_iomap() success for DEVICE_ALI
ALSA: hda - simplify azx_has_pm_runtime
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity in target land the last months.
The highlights include:
- Convert fabric drivers tree-wide to target_register_template() (hch
+ bart)
- iser-target hardening fixes + v1.0 improvements (sagi)
- Convert iscsi_thread_set usage to kthread.h + kill
iscsi_target_tq.c (sagi + nab)
- Add support for T10-PI WRITE_STRIP + READ_INSERT operation (mkp +
sagi + nab)
- DIF fixes for CONFIG_DEBUG_SG=y + UNMAP file emulation (akinobu +
sagi + mkp)
- Extended TCMU ABI v2 for future BIDI + DIF support (andy + ilias)
- Fix COMPARE_AND_WRITE handling for NO_ALLLOC drivers (hch + nab)
Thanks to everyone who contributed this round with new features,
bug-reports, fixes, cleanups and improvements.
Looking forward, it's currently shaping up to be a busy v4.2 as well"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (69 commits)
target: Put TCMU under a new config option
target: Version 2 of TCMU ABI
target: fix tcm_mod_builder.py
target/file: Fix UNMAP with DIF protection support
target/file: Fix SG table for prot_buf initialization
target/file: Fix BUG() when CONFIG_DEBUG_SG=y and DIF protection enabled
target: Make core_tmr_abort_task() skip TMFs
target/sbc: Update sbc_dif_generate pr_debug output
target/sbc: Make internal DIF emulation honor ->prot_checks
target/sbc: Return INVALID_CDB_FIELD if DIF + sess_prot_type disabled
target: Ensure sess_prot_type is saved across session restart
target/rd: Don't pass incomplete scatterlist entries to sbc_dif_verify_*
target: Remove the unused flag SCF_ACK_KREF
target: Fix two sparse warnings
target: Fix COMPARE_AND_WRITE with SG_TO_MEM_NOALLOC handling
target: simplify the target template registration API
target: simplify target_xcopy_init_pt_lun
target: remove the unused SCF_CMD_XCOPY_PASSTHROUGH flag
target/rd: reduce code duplication in rd_execute_rw()
tcm_loop: fixup tpgt string to integer conversion
...
Not much has been happening in PWM land lately, so this contains mostly
minor fixes that didn't seem urgent enough for a late pull-request last
cycle.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=X+q2
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"Not much has been happening in PWM land lately, so this contains
mostly minor fixes that didn't seem urgent enough for a late
pull-request last cycle"
* tag 'pwm/for-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: Remove __init initializer for pwm_add_table()
pwm: samsung: Fix output race on disabling
pwm: mxs: Fix period divider computation
pwm: atmel-hlcdc: Add errata handling for sama5d4
pwm: pca9685: Constify struct regmap_config
pwm: imx-pwm: add explicit compatible strings and required clock properties
- correction of copy-paste stupidity while doing the cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ULmO
-----END PGP SIGNATURE-----
Merge tag 'dma-buf-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf
Pull dma-buf updates from Sumit Semwal:
"Minor cleanup only; this could've gone in for the 4.0 merge window,
but for a copy-paste stupidity from me.
It has been in the for-next since then, and no issues reported.
- cleanup of dma_buf_export()
- correction of copy-paste stupidity while doing the cleanup"
* tag 'dma-buf-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf:
staging: android: ion: fix wrong init of dma_buf_export_info
dma-buf: cleanup dma_buf_export() to make it easily extensible
Highlights:
- "experimental" code for managing md/raid1 across a cluster using
DLM. Code is not ready for general use and triggers a WARNING if used.
However it is looking good and mostly done and having in mainline
will help co-ordinate development.
- RAID5/6 can now batch multiple (4K wide) stripe_heads so as to
handle a full (chunk wide) stripe as a single unit.
- RAID6 can now perform read-modify-write cycles which should
help performance on larger arrays: 6 or more devices.
- RAID5/6 stripe cache now grows and shrinks dynamically. The value
set is used as a minimum.
- Resync is now allowed to go a little faster than the 'mininum' when
there is competing IO. How much faster depends on the speed of the
devices, so the effective minimum should scale with device speed to
some extent.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=OHG6
-----END PGP SIGNATURE-----
Merge tag 'md/4.1' of git://neil.brown.name/md
Pull md updates from Neil Brown:
"More updates that usual this time. A few have performance impacts
which hould mostly be positive, but RAID5 (in particular) can be very
work-load ensitive... We'll have to wait and see.
Highlights:
- "experimental" code for managing md/raid1 across a cluster using
DLM. Code is not ready for general use and triggers a WARNING if
used. However it is looking good and mostly done and having in
mainline will help co-ordinate development.
- RAID5/6 can now batch multiple (4K wide) stripe_heads so as to
handle a full (chunk wide) stripe as a single unit.
- RAID6 can now perform read-modify-write cycles which should help
performance on larger arrays: 6 or more devices.
- RAID5/6 stripe cache now grows and shrinks dynamically. The value
set is used as a minimum.
- Resync is now allowed to go a little faster than the 'mininum' when
there is competing IO. How much faster depends on the speed of the
devices, so the effective minimum should scale with device speed to
some extent"
* tag 'md/4.1' of git://neil.brown.name/md: (58 commits)
md/raid5: don't do chunk aligned read on degraded array.
md/raid5: allow the stripe_cache to grow and shrink.
md/raid5: change ->inactive_blocked to a bit-flag.
md/raid5: move max_nr_stripes management into grow_one_stripe and drop_one_stripe
md/raid5: pass gfp_t arg to grow_one_stripe()
md/raid5: introduce configuration option rmw_level
md/raid5: activate raid6 rmw feature
md/raid6 algorithms: xor_syndrome() for SSE2
md/raid6 algorithms: xor_syndrome() for generic int
md/raid6 algorithms: improve test program
md/raid6 algorithms: delta syndrome functions
raid5: handle expansion/resync case with stripe batching
raid5: handle io error of batch list
RAID5: batch adjacent full stripe write
raid5: track overwrite disk count
raid5: add a new flag to track if a stripe can be batched
raid5: use flex_array for scribble data
md raid0: access mddev->queue (request queue member) conditionally because it is not set when accessed from dm-raid
md: allow resync to go faster when there is competing IO.
md: remove 'go_faster' option from ->sync_request()
...
- DT endianness specification bindings
- Big endian 8250 serial support
- DT overlay unittest updates
- Various DT doc updates
- Compile fixes for OF_IRQ=n
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVOG5kAAoJEMhvYp4jgsXihDgH/3pmPSjuRG1bhGssmnchHjWh
SU2eS2MZnlD60UqRt7jd3smCX2qL83tfwpFhOvCT9Mz775E7ggmYq9fS8pCYAbaD
x98mUrE2GzdUzlrL6RS8Z0ExjyGwbMoW3+cZtyPkmC6CsW0fwqEPmEyk7m+Hk8C3
w3pWG06o+G8UjiFmwbr8Pki2ykxvucr22NCzH4SS6bAD4QOrQO3v48QkUg7XFlVc
NHNzQbswL85uOJ7uuAbxg+s8TXkwcxUeMJEKldLrjuyppO3N1MjnOgCptnhVNOOb
zK+IsS378jMiNjAg2ui/BLH60N5yadkgk4+L4iPPy+y/yR61NCVXxRe11IQJxb0=
=rtv6
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull second batch of devicetree updates from Rob Herring:
"As Grant mentioned in the first devicetree pull request, here is the
2nd batch of DT changes for 4.1. The main remaining item here is the
endianness bindings and related 8250 driver support.
- DT endianness specification bindings
- big-endian 8250 serial support
- DT overlay unittest updates
- various DT doc updates
- compile fixes for OF_IRQ=n"
* tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
frv: add io{read,write}{16,32}be functions
mn10300: add io{read,write}{16,32}be functions
Documentation: DT bindings: add doc for Altera's SoCFPGA platform
of: base: improve of_get_next_child() kernel-doc
Doc: dt: arch_timer: discourage clock-frequency use
of: unittest: overlay: Keep track of created overlays
of/fdt: fix allocation size for device node path
serial: of_serial: Support big-endian register accesses
serial: 8250: Add support for big-endian MMIO accesses
of: Document {little,big,native}-endian bindings
of/fdt: Add endianness helper function for early init code
of: Add helper function to check MMIO register endianness
of/fdt: Remove "reg" data prints from early_init_dt_scan_memory
of: add vendor prefix for Artesyn
of: Add dummy of_irq_to_resource_table() for IRQ_OF=n
of: OF_IRQ should depend on IRQ_DOMAIN
This series introduces preliminary ACPI 5.1 support to the arm64 kernel
using the "hardware reduced" profile. We don't support any peripherals
yet, so it's fairly limited in scope:
- Memory init (UEFI)
- ACPI discovery (RSDP via UEFI)
- CPU init (FADT)
- GIC init (MADT)
- SMP boot (MADT + PSCI)
- ACPI Kconfig options (dependent on EXPERT)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJVNOC2AAoJELescNyEwWM08dIH/1Pn5xa04wwNDn0MOpbuQMk2
kHM7hx69fbXflTJpnZRVyFBjRxxr5qilA7rljAFLnFeF8Fcll/s5VNy7ElHKLISq
CB0ywgUfOd/sFJH57rcc67pC1b/XuqTbE1u1NFwvp2R3j1kGAEJWNA6SyxIP4bbc
NO5jScx0lQOJ3rrPAXBW8qlGkeUk7TPOQJtMrpftNXlFLFrR63rPaEmMZ9dWepBF
aRE4GXPvyUhpyv5o9RvlN5l8bQttiRJ3f9QjyG7NYhX0PXH3DyvGUzYlk2IoZtID
v3ssCQH3uRsAZHIBhaTyNqFnUIaDR825bvGqyG/tj2Dt3kQZiF+QrfnU5D9TuMw=
=zLJn
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull initial ACPI support for arm64 from Will Deacon:
"This series introduces preliminary ACPI 5.1 support to the arm64
kernel using the "hardware reduced" profile. We don't support any
peripherals yet, so it's fairly limited in scope:
- MEMORY init (UEFI)
- ACPI discovery (RSDP via UEFI)
- CPU init (FADT)
- GIC init (MADT)
- SMP boot (MADT + PSCI)
- ACPI Kconfig options (dependent on EXPERT)
ACPI for arm64 has been in development for a while now and hardware
has been available that can boot with either FDT or ACPI tables. This
has been made possible by both changes to the ACPI spec to cater for
ARM-based machines (known as "hardware-reduced" in ACPI parlance) but
also a Linaro-driven effort to get this supported on top of the Linux
kernel. This pull request is the result of that work.
These changes allow us to initialise the CPUs, interrupt controller,
and timers via ACPI tables, with memory information and cmdline coming
from EFI. We don't support a hybrid ACPI/FDT scheme. Of course,
there is still plenty of work to do (a serial console would be nice!)
but I expect that to happen on a per-driver basis after this core
series has been merged.
Anyway, the diff stat here is fairly horrible, but splitting this up
and merging it via all the different subsystems would have been
extremely painful. Instead, we've got all the relevant Acks in place
and I've not seen anything other than trivial (Kconfig) conflicts in
-next (for completeness, I've included my resolution below). Nearly
half of the insertions fall under Documentation/.
So, we'll see how this goes. Right now, it all depends on EXPERT and
I fully expect people to use FDT by default for the immediate future"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (31 commits)
ARM64 / ACPI: make acpi_map_gic_cpu_interface() as void function
ARM64 / ACPI: Ignore the return error value of acpi_map_gic_cpu_interface()
ARM64 / ACPI: fix usage of acpi_map_gic_cpu_interface
ARM64: kernel: acpi: honour acpi=force command line parameter
ARM64: kernel: acpi: refactor ACPI tables init and checks
ARM64: kernel: psci: let ACPI probe PSCI version
ARM64: kernel: psci: factor out probe function
ACPI: move arm64 GSI IRQ model to generic GSI IRQ layer
ARM64 / ACPI: Don't unflatten device tree if acpi=force is passed
ARM64 / ACPI: additions of ACPI documentation for arm64
Documentation: ACPI for ARM64
ARM64 / ACPI: Enable ARM64 in Kconfig
XEN / ACPI: Make XEN ACPI depend on X86
ARM64 / ACPI: Select ACPI_REDUCED_HARDWARE_ONLY if ACPI is enabled on ARM64
clocksource / arch_timer: Parse GTDT to initialize arch timer
irqchip: Add GICv2 specific ACPI boot support
ARM64 / ACPI: Introduce ACPI_IRQ_MODEL_GIC and register device's gsi
ACPI / processor: Make it possible to get CPU hardware ID via GICC
ACPI / processor: Introduce phys_cpuid_t for CPU hardware ID
ARM64 / ACPI: Parse MADT for SMP initialization
...
Pull ARM fixes from Russell King:
"A few fixes for the recently merged development updates:
- the update to convert a code branch in the procinfo structure
forgot to update the nommu code.
- VDSO only supported for V7 CPUs and later.
- VDSO build creates files which should be ignored by git but are not.
- ensure that make arch/arm/vdso/ doesn't build if it isn't enabled"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8344/1: VDSO: honor CONFIG_VDSO in Makefile
ARM: 8343/1: VDSO: add build artifacts to .gitignore
ARM: Fix nommu booting
ARM: 8342/1: VDSO: depend on CPU_V7
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nong
-----END PGP SIGNATURE-----
Merge tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux
Pull blackfin updates from Steven Miao.
* tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
eth: bf609 eth clock: add pclk clock for stmmac driver probe
blackfin: Wire up missing syscalls
arch: blackfin: kernel: kgdb: Remove unused function
dma: fix build error after update to v3.19
blackfin: io: define __raw_readx/writex with bfin_readx/writex
bf609: add resources for lcd nl8048
pm: sometimes wake up from suspend to RAM would fail
debug-mmrs: Eliminate all traces of the USB_PHY_TEST MMR
bf609: remove softswitch i2c configuration from adv7842 and adv7511 platform data
bf609: add platform data for soft switch devices on the video extenders
bf609: enable soft switch gpio driver by default
bf609: add gpio soft switch platform data for mcp23017 i2c devices
bf609: use new SND_BF6XX_PCM to choose audio pcm driver
bug[220] kgdb: change the smp cross core function entry
arch: blackfin: kernel: setup.c: Cleaning up missing null-terminate in conjunction with strncpy
blackfin: defconfigs: cleanup unused CONFIG_MTD_CHAR, add MTD_SPI_NOR for BF537-STAMP
Just the one change for v4.1-rc1. A minor cleanup of copy_thread().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=XxGr
-----END PGP SIGNATURE-----
Merge tag 'metag-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull Metag architecture updates from James Hogan:
"Just the one change for v4.1-rc1. A minor cleanup of copy_thread()"
* tag 'metag-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: copy_thread(): rename 'arg' argument to 'kthread_arg'
