Same patch we alredy did for Vega10. Just re-route page faults to a separate
ring to avoid drowning in interrupts.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Page faults can easily overwhelm the interrupt handler.
So to make sure that we never lose valuable interrupts on the primary ring
we re-route page faults to IH ring 1.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check if we get any values equal to 0, and set to 1 if so.
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Sivapiriyan Kumarasamy <Sivapiriyan.Kumarasamy@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adding thick tile mode for Oland to prevent UMD from getting mode value 0
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Tested-by: Hui.Deng <hui.deng@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/gpu/drm/amd/amdgpu/gfx_v8_0.c: In function ‘gfx_v8_0_tiling_mode_table_init’:
./include/linux/device.h:1487:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
_dev_warn(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/gfx_v8_0.c:3236:3: note: in expansion of macro ‘dev_warn’
dev_warn(adev->dev,
^~~~~~~~
drivers/gpu/drm/amd/amdgpu/gfx_v8_0.c:3240:2: note: here
case CHIP_CARRIZO:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The symbol for binary prefix kibi is "Ki", with uppercase K.
(In contrast, the symbol for decimal kilo is lowercase "k".)
Signed-off-by: Jakub Wilk <jwilk@jwilk.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Raven series doesn't support sw smu so far, so we have to add checking to
confirm it return false while the asic is raven.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To help xf86-video-amdgpu and mesa know DC supports updating the
tiling attributes for a framebuffer per-flip.
Cc: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
res_pool->pp_smu may be NULL. Check before use
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
AUX transaction returns success, but data has invalid lane count and rate
which when passed to VBIOS command table causes it to soft hang
[How]
Do some sanity checking and fail if the DPCD caps are invalid.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Tiling and DCC attributes can change when swapping framebuffers but
these will only ever get updated on full commits where
state->allow_modeset is true. But for the page-flip IOCTL
state->allow_modeset = false so these aren't updated and DCC changes
aren't being programmed.
[How]
Split out updating the tiling and DCC attributes into its own function
that's called when creating the plane for the first time but also
called when switching framebuffers before commit stream updates.
These functions also don't modify the plane state directly since the
plane state being used as reference is often the current one
being used by the hardware.
DC needs to be able to compare plane_state to the stream update
structures to determine if the hardware programming should happen. If
it's modified in place then nothing will be programmed and we can run
into concurrency issues.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The dc_gamma_type CUSTOM_GAMMA is used to represent degamma
mappings passed in by drm. This type of gamma must be interpolated
into a transfer function by apply_1d_lut. The line in
mod_color_calculate_degamma_params that handled this case
was erroneously removed.
[How]
For CUSTOM_GAMMA degamma, calculate the lut as before.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 6bff1cc7780cca2fd2a775aa7b18b789e2a1b608.
[Description]
Revert since this will be checked at CP side.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
used to be unable to run 4:2:0 if using a dongle because 4k60 bandwidth
exceeded dongle caps
[How]
half pixel clock during comparison to dongle cap. *Could get stuck on black
screen on monitor that don't support 420 but will be selecting 420 as
preferred mode*
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Aidan Wood <Aidan.Wood@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
UEFI boot usually uses a boot profile that uses higher clocks
and watermark settings.
UEFI boot surface is less optimal, for example it uses linear surface
[How]
Before we finish our seamless boot sequence, keep the clock and
watermark settings from boot.
Update to optimal settings only after first flip away from UEFI
frame buffer.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
commit_planes is indented quite far
[How]
Move the pageflip code from an if statement to after a
continue
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
IGT expects that pageflips can be triggered with the same
framebuffer before and after the commit
[How]
Expand the definition of pageflip to include any change
with an old framebuffer and a new framebuffer, even if they're
the same
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Raven has support for combining pipes for DRM_PLANE_TYPE_OVERLAY use
but no overlays are exposed to userspace.
[How]
Expose overlay planes based on DC plane caps.
If all the pipes are in use then the atomic commits can fail, but this
is expected behavior for userspace.
Only support RGB on overlays for now.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Primary and underlay planes were previously exposed to DRM by using
max_planes and max_slave_planes.
The value for max_planes was always pipe_count + has_underlay.
If there was an underlay pipe, then max_slave_planes = 1.
Raven has pipe_count = 4, max_planes = 4, and max_slave_planes = 1.
So during plane initialziation it was actually "creating"
1 overlay plane and 3 primary planes... or it would be, had its
plane_type array not been dm_plane_type_default, which will only create
DRM_PLANE_TYPE_PRIMARY planes.
We can expose primary planes as supporting more than one CRTC at a time
to more closely resemble plane behavior on DCN but userspace doesn't
really expect planes to be used in this manner and will either
ignore the planes or crash.
Planes with index greater than max_streams are marked as supporting
all CRTCs. No ASIC currently has primary plane count greater than the
stream count but we shouldn't expose more than necessary.
[How]
Drop support for underlay planes. They aren't well tested and don't
fully work right at the moment.
Only create one primary plane per CRTC so we're not creating overlays.
Initialize plane types directly instead of referencing a misleading
array of plane types.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The current dc_caps doesn't provide the information needed to
determine the count and type of each plane to be exposed to userspace.
There are three types of DRM planes that are exposed to userspace:
1. Primary planes (can be used for modesetting)
2. Overlay planes (can be blended below or above a primary plane)
3. Cursor planes (blended topmost)
We need to know the number and type of each in amdgpu_dm to expose
to userspace.
Hardware supports blending planes below, above or both ways depending
on the ASIC. Alpha support is also ASIC dependent. Some hardware has
dedicated pipes for overlays and other hardware combines the pipes.
All of this should be exposed in a way that DM can query and use.
[How]
Introduce the dc_plane_cap structure that describes the capabilities
for the hw planes.
It describes:
- the type of the plane
- whether the plane can blend with planes below it
- whether the plane can blend with planes above it
- whether the plane supports per pixel alpha blending
- supported formats on the plane (partial list for now)
Pre DCN ASICs don't have their full capabilities described for now.
They can be updated as needed in the future.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The kms_plane@plane-position-covered-pipe-*-planes subtests can produce
a sequence of atomic commits such that neither active_changed nor
mode_changed but connectors_changed.
When this happens we remove the old stream from the context and add
a new stream but the new stream doesn't have mode_changed=true set.
This incorrect programming sequence causes CRC mismatches to occur in
the test.
The stream->mode_changed value should be set whenever a new stream
is created.
[How]
A new stream is created whenever drm_atomic_crtc_needs_modeset is true.
We previously covered the active_changed and mode_changed conditions
for the CRTC but connectors_changed is also checked within
drm_atomic_crtc_needs_modeset.
So just use drm_atomic_crtc_needs_modeset directly to determine the
mode_changed flag.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The new aux implementation was not up to spec. This caused us to fail DP
compliance as well as introduced serious delays during system resume.
[How]
Make dce_aux_transfer_raw return the operation result
Make dce_aux_transfer_with_retries delay with udelay instead
of msleep, and only on invalid reply. Also fail on the second
invalid reply, third timeout, or first of any other error
Convert return values to drm error codes in amdgpu_dm
As the two aux transfer functions are now noticeably
different, change the names to better reflect their
functionality and document.
There was one last call to dc_link_aux_transfer that
should have retries, fix that
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Eric Yang <eric.yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In some cases we might need to do a full update. Add a commit_hints
struct for future use
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With special monitor combination on MST, the UP_REQ could come
after clear payload table. It makes the pending DOWN_REP fail
to be handled after link training and the new DOWN_REQ will be queued
until time out .
[How]
To move the current polling pending DOWN_REP procedure to after
clear payload table to make sure the pending DOWN_REP can be
done before enabling the link.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add 6 files that return (in bytes):
The total amount of VRAM/visible VRAM/GTT
and the current total used VRAM/visible VRAM/GTT
v2: Split used and total into separate files
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Kent Russell <kent.russell@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add condition to judge whether overdrive is enabled and correct power
limit value for overdrive used by power limit interface.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move pp_feature from the struct of amd_powerplay to amdgpu_device.
Add pp_feature limit for overdrive interface.
v2: put pp_feature into struct amdgpu_pm.
v3: merge feature_mask with pp_feature.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Suggested-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch uses REG32_PCIE wrapper instead of writting pci_index2 and reading
pci_data2. This sequence should be protected by pcie_idx_lock.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The vega20_message_map[index] scope should be in PPSMC_Message_Count not in
SMU_MSG_MAX_COUNT.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch moves setting allowed mask and feature enabling together to refine
the programming sequence.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The smu_11_0_powerplay_table, smu_11_0_power_saving_clock_table, and
smu_11_0_overdrive_table need byte alignment. So we must add packed attribute
in the definitions.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We actually want to know the index of PPSMC_MSG.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add sys interface to set and get pcie info for smu.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Gui Chengming <Jack.Gui@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
PCIE parameters should be override to fix the conflict between the ASIC
capabilities and the system capabilities.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Gui Chengming <Jack.Gui@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add sys interface to set socclk, fclk and dcefclk for smu.
Add feature_mask parameter for smu_upload_dpm_level as socclk, fclk and
dcefclk have dependency, without feature_mask to point out specific clk
will make it fail to set some clk.
Fix the function of smu_unforce_dpm_levels.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Gui Chengming <Jack.Gui@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add sys interface to get socclk, fclk and dcefclk for smu.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Gui Chengming <Jack.Gui@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Smc table hw init should be skipped for suspend/resume when dpm running.
Unified feature enable and disable function into smu_system_features_control.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Functional the function of smu suspend and resume.
Modified the function of smu_smc_table_hw_init to make it useful for smu
resume.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add is_dpm_running function to support smu s3 case.
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set default dpm table fo vclk, dclk and eclk.
Open clk adjust rules for vclk, dclk.
v2: Open clk adjust rules for eclk.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Get eclk, vclk and dclk info from vbios when hw init for smu11.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add fan1_target set interface to set fan speed for hwmon.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
set the fan1_enable hwmon interface to call
smu_get_fan_control_mode and smu_set_fan_control_mode.
v2: fix print value.
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1, set get_pwm1_enable and set_pwm1_enable functions to call
smu_get_fan_control_mode and smu_set_fan_control_mode for SMU11
2, implement set_fan_control_mode function
v2: add return value in set_fan_control_mode function
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add AMDGPU_PP_SENSOR_STABLE_PSTATE_SCLK and
AMDGPU_PP_SENSOR_STABLE_PSTATE_MCLK to support
read sensor for SMU11.
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Kevin Wang <kevink1.wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
