Hook up "pm_power_off" to palmas power off routine if there is DT
property "ti,system-power-controller" defined, so platform which is
powered by this regulator can be powered off properly.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mallikarjun Kasoju <mkasoju@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds clock to list of mfd cells for s2mps11 and DT documentation
for clock part.
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
FX_CTRL2 is a volatile register and should be marked as such, this patch
does so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The mic detect level registers are used from common code to configure
the button detection code. Add these registers to the defaults list and
mark them as readable for wm5110.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The FLL gains are present on all devices and controlled from common code
shared between them. This patch adds these registers into defaults list
for wm5110 and marks them as readable.
Reported-by: D.J. Barrow <dbarrow@wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reg_cache variable is used to lock step enable register
from being accessed and written by both TSC and ADC
at the same time.
However, it isn't updated anywhere in the code at all.
If both TSC and ADC are used, eventually 1FFFF is always
written enabling all 16 steps uselessly causing a mess.
Patch fixes it by correcting the locks and updates the
variable by reading the step enable register
Signed-off-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we disable DCVDD before we mark the cache as cache only, we might
attempt to write to the chip whilst it is powered down and lose a write.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the build
warnings when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled.
drivers/mfd/ab8500-gpadc.c:891:12: warning: 'ab8500_gpadc_suspend' defined but not used [-Wunused-function]
drivers/mfd/ab8500-gpadc.c:903:12: warning: 'ab8500_gpadc_resume' defined but not used [-Wunused-function]
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add CONFIG_PM_RUNTIME to runtime_suspend/runtime_resume functions
to fix the build warnings when CONFIG_PM_RUNTIME is not selected.
This is because runtime PM callbacks defined by SET_RUNTIME_PM_OPS
are only used when the CONFIG_PM_RUNTIME is enabled.
drivers/mfd/ab8500-gpadc.c:870:12: warning: 'ab8500_gpadc_runtime_suspend' defined but not used [-Wunused-function]
drivers/mfd/ab8500-gpadc.c:878:12: warning: 'ab8500_gpadc_runtime_resume' defined but not used [-Wunused-function]
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the build
warnings when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled.
drivers/mfd/ucb1x00-core.c:672:12: warning: 'ucb1x00_suspend' defined but not used [-Wunused-function]
drivers/mfd/ucb1x00-core.c:704:12: warning: 'ucb1x00_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
'mmc_callback_data' and 'vtg' are pointers.
Fix the following sparse warning:
drivers/mfd/menelaus.c:445:43: warning: Using plain integer as NULL pointer
drivers/mfd/menelaus.c:469:20: warning: Using plain integer as NULL pointer
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
twl4030_power_configure_scripts(), twl4030_power_configure_resources(),
twl4030_power_probe() are used only in this file.
Fix the following sparse warnings:
drivers/mfd/twl4030-power.c:496:5: warning: symbol 'twl4030_power_configure_scripts' was not declared. Should it be static?
drivers/mfd/twl4030-power.c:512:5: warning: symbol 'twl4030_power_configure_resources' was not declared. Should it be static?
drivers/mfd/twl4030-power.c:556:5: warning: symbol 'twl4030_power_probe' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
'lpc_chipset_info' is used only in this file.
Fix the following sparse warning:
drivers/mfd/lpc_ich.c:216:21: warning: symbol 'lpc_chipset_info' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Casting (void *) data of max8997_pmic_dt_match is necessary,
because variable 'data' of struct 'of_device_id' is defined as
'const void *data'. Thus, pointer should be used instead of value.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is only called from this file so there is no need for it to be in the
global namespace and cause sparse to warn.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since the conversion to the regmap API setting bits per word will lead to
data corruption since the regmap API already configures the bits per word
appropriately.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixes this compilation error:
linux/include/linux/mfd/ucb1x00.h:137:17: error: field 'dev' has incomplete type
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixes this compilation error:
linux/include/linux/mfd/mcp.h:22:16: error: field 'attached_device' has incomplete type
linux/include/linux/mfd/mcp.h:48:23: error: field 'drv' has incomplete type
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
AFE Pen Ctrl and TouchScreen transistors enabling is not
required when only ADC mode is being used, so check for availability of
TSC driver before accessing control register.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ADC is ideally expected to work at a frequency of 3MHz.
The present code had a check, which returned error if the frequency
went below the threshold value. But since AM335x supports various
working frequencies, this check is not required.
Now the code just uses the internal ADC clock divider to set the ADC
frequency w.r.t the sys clock.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since enabling VMID takes a runtime PM reference there is no need to
suppress suspend when doing a runtime suspend. Similarly the digital
inputs and outputs are DAPM widgets and therefore the ASoC core will
be holding a reference for them.
This used to be required when integration with system suspend was being
bodged.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The jack detection code holds runtime PM references when required so
there is no need for suspend to do any checks.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Kconfig prompt for WM8997 says "Support for..." while the other MFD
Kconfigs (including the adjacent ones for other Arizona devices) just
list the device name which sticks out like a sore thumb when doing
configuration.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since these are fixed rate clocks which are registered with common clock
framework so remove these from list of regulators which were unnecessarily
incrementing the count(S2MPS11_REGULATOR_MAX) of regulators.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
During a move to use managed resources, the .remove function all was
deemed superfluous which subsequently led to its deletion. As there are
no remaining users of the stored 'base' address we only have to use it
locally during probe.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The err: label is not needed we can just return instead of the jump there.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
To comply with coding style.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TWL6040 is used only with OMAP4/5 SoCs and they can only boot in in DT mode.
The support for pdata/legacy boot can be removed.
Add TODO comment to the header file that all pdata struct can be removed in
the next merge window (after the sub driver updates are in).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The performance of regmap-irq is improved if the interrupt mask registers
can be cached since it does read/modify/update cycles so start using the
register cache infrastructure for those registers. We should use this more
widely but I don't have a datasheet and this is a nice, conservative
starting point.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
DA9055 is a combination of pmic and codec. This patch updates the DA9055 i2c
device id name to match the standard naming convention followed for such chips.
Signed-off-by: Ankur Raina <Ankur.Raina@kpitcummins.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch clears all the events received while powering up DA9055.
While powering up DA9055, both power sequencer and gpio events are received.
These events remain uncleared after boot up, due to which further event handling
also fails. DA9055 has three event registers. The event register bits are set
to '1' on receiving an event. The events can be cleared on writing a '1' to
the set bit, which would then clear that bit to '0'. After applying this patch
we have a clean state after boot up.
Signed-off-by: Ankur Raina <Ankur.Raina@kpitcummins.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds DT compatible string for s2mps11 and binding documentation.
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add TPS659038 Device Tree documentation.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
- Driver fixes for AM33xx, SIRF and PFC pin controllers.
- Fix a compile warning from the pinctrl single-register
driver.
- Fix a little nasty memory leak.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=URtB
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Driver fixes for AM33xx, SIRF and PFC pin controllers
- Fix a compile warning from the pinctrl single-register driver
- Fix a little nasty memory leak
* tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: fix a memleak when freeing maps
pinctrl: pinctrl-single: fix compile warning when no CONFIG_PM
pinctrl: sh-pfc: fix SDHI0 VccQ regulator on sh73a0 with DT
arm/dts: sirf: fix the pingroup name mismatch between drivers and dts
pinctrl: sirf: add usp0_uart_nostreamctrl pin group for usp-uart without flowctrl
pinctrl: sirf: fix the pin number and mux bit for usp0
pinctrl: am33xx dt binding: correct include path
and deleting that event at the same time (both must be done as root).
I also found a bug while testing Oleg's patches which has to do with
a race with kprobes using the function tracer.
There's also a deadlock fix that was introduced with the previous fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJR8nMiAAoJEOdOSU1xswtMXMMH/jNuG1vDcTjo7WXu3kYHJNWc
u1Z3YPXunFozz4DofzXPCuSkSgRqSR4cVeGOAv3oEfwQv07jJdTAor8/FuVTNXW9
yiGMUvth0nLVZQEmsh3VvVztqFy8FxhpnQHhIa6pillPUdROKgE/A7/q4wT37lxT
qniM1QJTK9fIf2t6suMwSsBD7fepiDkdHwVbs5NvN7qj62/QSPN+pHLAOBl90AGp
r5eUSj8cDHxmzlV+GAJxeqI7KH+P2PGts9USI+s5EX8mODci620jz1HkKab6XRpz
ggYdNzJ21z1fO9vfnpGCF0d03sKdnbJoIQjkyD4AJHlojmLe3s6l/nxS6jg3wH8=
=VrR4
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Oleg is working on fixing a very tight race between opening a event
file and deleting that event at the same time (both must be done as
root).
I also found a bug while testing Oleg's patches which has to do with a
race with kprobes using the function tracer.
There's also a deadlock fix that was introduced with the previous
fixes"
* tag 'trace-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Remove locking trace_types_lock from tracing_reset_all_online_cpus()
ftrace: Add check for NULL regs if ops has SAVE_REGS set
tracing: Kill trace_cpu struct/members
tracing: Change tracing_fops/snapshot_fops to rely on tracing_get_cpu()
tracing: Change tracing_entries_fops to rely on tracing_get_cpu()
tracing: Change tracing_stats_fops to rely on tracing_get_cpu()
tracing: Change tracing_buffers_fops to rely on tracing_get_cpu()
tracing: Change tracing_pipe_fops() to rely on tracing_get_cpu()
tracing: Introduce trace_create_cpu_file() and tracing_get_cpu()
This is five bug fixes, two of which fix long standing problems causing
crashes (sd and mvsas). The remaining three are hung (isci race) or lost
(qla2xxx, isci) devices.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJR8+WtAAoJEDeqqVYsXL0MDIUIAKkm+XVgNPAUhDnPH5IUcHVB
jr0NnKnsmlWVNV/Jc8xYKAjPeyBGr4foMR4W+Qqy2g8tTXI55AkXq4A8lyJfYVj9
1j8HTdbJFcOIwQO3e4gp6yJ9j2AdMoM9eHMYqts9u/G+2ckQm8GyMksgttUatVPu
gShyvU2Er546Di6D+JKNMjLufMucnuyPBHmzAKFc9l0L8A31vE0zkbO1qGozDTEB
tDotPSRuaaHaNQDvP/V0uwEIA1/KTq50ZJQerFp/mhc+gAvC/bQlmiOpWEJ8BxW7
3L0TEBsU+Bq1f+1uIWCHk3NWZEjj7nFLfk2lkhh32UtfXMB8Io46PbQAC9/Nk6U=
=/0W8
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is five bug fixes, two of which fix long standing problems
causing crashes (sd and mvsas). The remaining three are hung (isci
race) or lost (qla2xxx, isci) devices"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] isci: fix breakage caused by >16byte CDB patch
[SCSI] mvsas: Fix kernel panic on tile due to unaligned data access
[SCSI] sd: fix crash when UA received on DIF enabled device
[SCSI] qla2xxx: Properly set the tagging for commands.
[SCSI] isci: Fix a race condition in the SSP task management path
Pull drm fixes from Dave Airlie:
"This is just a regular fixes pull apart from the qxl one, it has
radeon and intel bits in it,
The intel fixes are for a regression with the RC6 fix and a 3.10 hdmi
regression, whereas radeon is more DPM fixes, a few lockup fixes and
some rn50/r100 DAC fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/dpm: fix r600_enable_sclk_control()
drm/radeon/dpm: implement force performance levels for rv6xx
drm/radeon/dpm: fix displaygap programming on rv6xx
drm/radeon/dpm: fix a typo in the rv6xx mclk setup
drm/i915: initialize gt_lock early with other spin locks
drm/i915: fix hdmi portclock limits
drm/radeon: fix combios tables on older cards
drm/radeon: improve dac adjust heuristics for legacy pdac
drm/radeon: Another card with wrong primary dac adj
drm/radeon: fix endian issues with DP handling (v3)
drm/radeon/vm: only align the pt base to 32k
drm/radeon: wait for 3D idle before using CP DMA
Pull qxl drm fixes from Dave Airlie:
"Okay as I warned, the qxl driver was running a bit free and loose with
its ttm object reservations and the new lockdep enabled reservation
tracking shone a bright light into it, it also with the new
reservations mutexes hits a possible deadlock during boot.
The first patch is a real fix to render the console correctly as the
driver used to just drop irq renderering as too hard, this also fixes
a sleeping while atomic warning.
The other two patches are the big ugly ones that redo how the driver
allocates objects and reserves them and makes things all work
properly, I've tested this in a VM, and compared to the current code
which hits a lockdep warning and the sleep while atomic warning before
failing.
So sorry this is coming in late, I should have tested qxl before
merging the mutex code, but I'd rather just fix qxl with this than
revert the reservations code at this point"
* 'qxl-fixes' of git://people.freedesktop.org/~airlied/linux:
qxl: convert qxl driver to proper use for reservations
qxl: allow creation of pre-pinned objects and use for releases.
drm/qxl: add delayed fb operations
- Revert of the ACPI video commit that I hoped would help fix
backlight problems related to Windows 8 compatibility on some
systems. Unfortunately, it turned out to cause problems to happen
too.
- Fix for two problems in intel_pstate, a possible failure to respond
to a load change on a quiet system and a possible failure to select
the highest available P-state on some systems. From Dirk Brandewie.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=mGfr
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are just two fixes, a revert of the would-be backlight fix that
didn't work and an intel_pstate fix for two problems related to
maximum P-state selection.
Specifics:
- Revert of the ACPI video commit that I hoped would help fix
backlight problems related to Windows 8 compatibility on some
systems. Unfortunately, it turned out to cause problems to happen
too.
- Fix for two problems in intel_pstate, a possible failure to respond
to a load change on a quiet system and a possible failure to select
the highest available P-state on some systems. From Dirk
Brandewie"
* tag 'pm+acpi-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI / video / i915: No ACPI backlight if firmware expects Windows 8"
cpufreq / intel_pstate: Change to scale off of max P-state
This is a largeish batch of fixes, mostly because I missed -rc2 due to
travel/vacation. So in number these are a bit more than ideal unless
you amortize them over two -rcs.
Quick breakdown:
- Defconfig updates
- Making multi_v7_defconfig useful on more hardware to encourage
single-image usage
- Davinci and nomadik updates due to new code merged this merge window
- Fixes for UART on Samsung platforms, both PM and clock-related
- A handful of warning fixes from defconfig builds, including for
max8925 backlight and pxamci (both with appropriate acks)
- Exynos5440 fixes for LPAE configuration, PM
- ...plus a bunch of other smaller changes all over the place
I expect to switch to regressions-or-severe-bugs-only fixes from here
on out.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=XOG3
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is a largeish batch of fixes, mostly because I missed -rc2 due to
travel/vacation. So in number these are a bit more than ideal unless
you amortize them over two -rcs.
Quick breakdown:
- Defconfig updates
- Making multi_v7_defconfig useful on more hardware to encourage
single-image usage
- Davinci and nomadik updates due to new code merged this merge
window
- Fixes for UART on Samsung platforms, both PM and clock-related
- A handful of warning fixes from defconfig builds, including for
max8925 backlight and pxamci (both with appropriate acks)
- Exynos5440 fixes for LPAE configuration, PM
- ...plus a bunch of other smaller changes all over the place
I expect to switch to regressions-or-severe-bugs-only fixes from here
on out"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
mfd: max8925: fix dt code for backlight
ARM: omap5: Only select errata 798181 if SMP
ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos
ARM: EXYNOS: Fix low level debug support
ARM: SAMSUNG: Save/restore only selected uart's registers
ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm
ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
ARM: multi_v7_defconfig: Select USB chipidea driver
ARM: pxa: propagate errors from regulator_enable() to pxamci
ARM: zynq: fix compilation warning
ARM: keystone: fix compilation warning
ARM: highbank: Only touch common coherency control register fields
ARM: footbridge: fix overlapping PCI mappings
dmaengine: shdma: fix a build failure on platforms with no DMA support
ARM: STi: Set correct ARM ERRATAs.
ARM: dts: STi: Fix pinconf setup for STiH416 serial2
ARM: nomadik: configure for NO_HZ and HRTIMERS
ARM: nomadik: update defconfig base
ARM: nomadik: Update MMC defconfigs
ARM: davinci: defconfig: enable EDMA driver
...
Here are a number of USB fixes for 3.11-rc3.
Lots of little things, nothing major. A number of new device ids, build
fixes for DMA, and a bunch of other minor things. All of these have
been in the linux-next tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlHyp6cACgkQMUfUDdst+ynfQACfb+akG9GYjNpdjkiun0dh2DG2
hDYAoKuhkL1L63vDcIjfFOdZpVKetjPi
=71aA
-----END PGP SIGNATURE-----
Merge tag 'usb-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 3.11-rc3.
Lots of little things, nothing major. A number of new device ids,
build fixes for DMA, and a bunch of other minor things. All of these
have been in the linux-next tree"
* tag 'usb-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (40 commits)
usb: Clear both buffers when clearing a control transfer TT buffer.
usb/gadget: free opts struct on error recovery
USB: mos7840: fix memory leak in open
usb: serial: option.c: remove ONDA MT825UP product ID fromdriver
usb: serial: option: add Olivetti Olicard 200
usb: serial: option: blacklist ONDA MT689DC QMI interface
xhci: fix null pointer dereference on ring_doorbell_for_active_rings
usb: host: xhci: Enable XHCI_SPURIOUS_SUCCESS for all controllers with xhci 1.0
usb: fix build warning in pci-quirks.h when CONFIG_PCI is not enabled
usb: xhci: Mark two functions __maybe_unused
xhci: Avoid NULL pointer deref when host dies.
usb: serial: option: Add ONYX 3G device support
USB: ti_usb_3410_5052: fix dynamic-id matching
usb: option: add TP-LINK MA260
USB: option: add D-Link DWM-152/C1 and DWM-156/C1
USB: EHCI: Fix resume signalling on remote wakeup
USB: cp210x: add MMB and PI ZigBee USB Device Support
usb: cp210x support SEL C662 Vendor/Device
USB: option: append Petatel NP10T device to GSM modems list
USB: misc: Add Manhattan Hi-Speed USB DVI Converter to sisusbvga
...
Here are 3 fixes for TTY and serial issues that have been reported.
Nothing huge, but nice to get fixed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlHyqbQACgkQMUfUDdst+ylRnACgxsIFAvjVszn4nIjPtrsP+SUD
dooAnjL/xGoi6MdJ92mrjTZ4rjUQgw2Z
=bJyY
-----END PGP SIGNATURE-----
Merge tag 'tty-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are 3 fixes for TTY and serial issues that have been reported.
Nothing huge, but nice to get fixed"
* tag 'tty-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: tegra: correct help message in Kconfig from 'ttyHS' to 'ttyTHS'
tty/8250_early: Don't truncate last character of options
TTY: snyclinkmp: calculating wrong addresses
Here are some tiny drivers/staging/ fixes for 3.11-rc3
A number of bugfixes, all pretty tiny, but resolve issues that have been
reported (the kstrtos32 change fixes a data corruption problem that Dan
found.) And a MAINTAINERS file update for the comedi drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlHyqLIACgkQMUfUDdst+ylR1gCglBMx4nQjWc7Bp5653TQFqveg
F6cAnRnDxVutdUv1WJwhLH7JJT+HQniN
=/dxc
-----END PGP SIGNATURE-----
Merge tag 'staging-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some tiny drivers/staging/ fixes for 3.11-rc3
A number of bugfixes, all pretty tiny, but resolve issues that have
been reported (the kstrtos32 change fixes a data corruption problem
that Dan found). And a MAINTAINERS file update for the comedi
drivers"
* tag 'staging-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
MAINTAINERS: Update the list of maintainers for staging/comedi driver.
staging: tidspbridge: replace strict_strtol() with kstrtos32()
staging: android: logger: Correct write offset reset on error
staging: zram: protect zram_reset_device() call
staging: gdm72xx: potential use after free in send_qos_list()
staging: drm/imx: drop "select OF_VIDEOMODE"
staging: frontier: use after free in disconnect()
staging: comedi: fix a race between do_cmd_ioctl() and read/write
staging: comedi: COMEDI_CANCEL ioctl should wake up read/write
Here are some char/misc patches for 3.11-rc3. It's pretty much just:
- mei fixes
- hyperv fixes
- new ja_JP translation update
all tiny stuff, but fixes for issues people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlHyqBcACgkQMUfUDdst+ylMswCgoppo0tfChc0KfyAcsgWwJr2o
iTsAoLEJ2sg8GIGYI765UMXWAkzJyCxR
=oHJj
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc patches from Greg KH:
"Here are some char/misc patches for 3.11-rc3. It's pretty much just:
- mei fixes
- hyperv fixes
- new ja_JP translation update
all tiny stuff, but fixes for issues people have reported."
* tag 'char-misc-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
HOWTO ja_JP sync
mei: me: fix waiting for hw ready
mei: don't have to clean the state on power up
mei: me: fix reset state machine
mei: hbm: fix typo in error message
Tools: hv: KVP: Fix a bug in IPV6 subnet enumeration
Drivers: hv: balloon: Do not post pressure status if interrupted
Drivers: hv: balloon: Fix a bug in the hot-add code
Drivers: hv: vmbus: incorrect device name is printed when child device is unregistered
Just a handfull of regression and small fixes in ASoC, HD-audio
and USB-audio drivers.
- Sigmetal HD-audio codec regression fixes
- A copule of XRUN indication fixes for usb-audio devices
- ASoC: ep93xx build fix, sgtl5000 fix for probe order changes,
max98088 register access fix, etc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=7CQ7
-----END PGP SIGNATURE-----
Merge tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a handful of regression and small fixes in ASoC, HD-audio and
USB-audio drivers.
- Sigmetal HD-audio codec regression fixes
- A copule of XRUN indication fixes for usb-audio devices
- ASoC: ep93xx build fix, sgtl5000 fix for probe order changes,
max98088 register access fix, etc"
* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hiface: return correct XRUN indication
ASoC: tegra: correct playback_dma_data setup
ASoC: core: double free in snd_soc_add_platform()
ALSA: usb-audio: 6fire: return correct XRUN indication
ASoC: ep93xx: fix build of ep93xx-ac97.c
ALSA: hda - Remove NO_PRESENCE bit override for Dell 1420n Laptop
ALSA: hda - Fix EAPD GPIO control for Sigmatel codecs
ASoC: atmel-ssc: remove clk_disable_unprepare call from critical section
ASoC: sgtl5000: defer the probe if clock is not found
ASoC: max98088 - fix element type of the register cache.
- fix for regression in commit cca9f93a52, recovery causing filesystem
corruption after a crash
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=hrYY
-----END PGP SIGNATURE-----
Merge tag 'for-linus-v3.11-rc3' of git://oss.sgi.com/xfs/xfs
Pull xfs fix from Ben Myers:
"Fix for regression in commit cca9f93a52 ("xfs: don't do IO when
creating an new inode"), recovery causing filesystem corruption after
a crash"
* tag 'for-linus-v3.11-rc3' of git://oss.sgi.com/xfs/xfs:
xfs: di_flushiter considered harmful
