Add nodes for the UFS controller and PHY, and enable these for the MTP
with relevant supplies specified.
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200415061430.740854-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add RPMh controlled regulators for the three PMICs and specify voltage
ranges and mode for relevant regulators.
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200415061430.740854-2-bjorn.andersson@linaro.org
[bjorn: Fixed up some supplies and voltages]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This was mistakenly copied from the downstream dts, however the upstream
driver works differently.
I only tested this with the pm8150_gpios node (used with volume button),
but the 2 others should be the same.
Fixes: e92b61c8e7 ("arm64: dts: qcom: pm8150l: Add base dts file")
Fixes: 229d5bcad0 ("arm64: dts: qcom: pm8150b: Add base dts file")
Fixes: 5101f22a5c ("arm64: dts: qcom: pm8150: Add base dts file")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200420153543.14512-1-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch re-arranges ipq8074 device nodes based on node address
followed by node names followed by node labels.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Link: https://lore.kernel.org/r/1586572830-22727-1-git-send-email-sivaprak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Changed polling-delay and polling-delay-passive to zero to disable
polling mode of the framework as interrupts for tsens are already
configured.
Signed-off-by: Rajeshwari <rkambl@codeaurora.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/1586244677-14399-1-git-send-email-rkambl@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The thermal trip points have unit name but no reg property, so we can
remove them. It also fixes the following warnings from 'make dtbs_check'
after adding the thermal yaml bindings.
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu4-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu5-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu6-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu7-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
clust0-mhm-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
clust1-mhm-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
mem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
wlan-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
multimedia-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu4-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu5-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu6-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu7-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
clust0-mhm-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
clust1-mhm-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
mem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
wlan-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
multimedia-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/cd6f0c7298437d35642b35c9ede9064c247d6090.1585562459.git.amit.kucheria@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The thermal trip points have unit name but no reg property, so we can
remove them. It also fixes the following warnings from 'make dtbs_check'
after adding the thermal yaml bindings.
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
m4m-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
l3-or-venus-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cluster0-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
mem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
modemtx-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
m4m-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
l3-or-venus-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cluster0-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
mem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
modemtx-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/2c0aa5357c96c3caff8554f9ef3ab9c5a2b8d2f8.1585562459.git.amit.kucheria@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The thermal trip points have unit name but no reg property, so we can
remove them. It also fixes the following warnings from 'make dtbs_check'
after adding the thermal yaml bindings.
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
gpu-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
gpu-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/2d3d045c18a2fb85b28cf304aa11ae6e6538d75e.1585562459.git.amit.kucheria@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add DISP_CC_MDSS_ROT_CLK and DISP_CC_MDSS_AHB_CLK
in the assigned clocks list as these are display
specific clocks and needs to be initialized from
the client side. Adding the default rate of
19.2 mhz for these clocks for sc7180 target.
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Link: https://lore.kernel.org/r/1584709864-5587-1-git-send-email-mkrishn@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Re-introduce the include of the sc7180 interconnect node name
definitions. Though this was part of v5 of the interconnect provider
series [1], it was dropped because the DT changes went through a
different tree than the header. Re-add that now.
Interconnect clients being introduced can reference this patch as a
dependency, rather than racing each other to add the include.
[1] https://patchwork.kernel.org/patch/11417989/
Signed-off-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20200310161502.1.Ia2884ed3c8826f52fbd5dcfa7a376a2fac4f31e6@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enable the ov8856 main camera and the ov7251 b/w tracking camera
used on the Qualcomm RB3 kit.
Currently the camera nodes have not yet been attached to an to a
CSI2 endpoint, since no driver currently supports the ISP that the the
SDM845/db845c ships with.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200324155843.10719-6-robert.foss@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add pm_8998 GPIO trace names. These names are defined in
the 96boards db845c mezzanine schematic.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200324155843.10719-5-robert.foss@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The sdm845 SOC ships with a CCI controller, which
has two CCI/I2C buses.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200324155843.10719-4-robert.foss@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch enables the primary and secondary USB controllers on the
qcs404-evb.
Primary:
The primary USB controller has
- One USB3 SS PHY using gpio-usb-conn
- One USB2 HS PHY in device mode only and no connector driver
associated.
Secondary:
The second DWC3 controller which has one USB Hi-Speed PHY attached to it.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200311191517.8221-7-bryan.odonoghue@linaro.org
[bjorn: Dropped usb3 role switching and enabled vbus]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Rather than set the minimum microvolt for this regulator in the USB SS PHY
driver, set it in the DTS.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200311191517.8221-6-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
VBUS is supplied by an external regulator controlled by a GPIO pin. This
patch models the regulator as regulator-usb3-vbus.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200311191517.8221-5-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The USB ID pin is used to tell if a system is a Host or a Device. For our
purposes we will bind this pin into gpio-usb-conn later.
For now define the pin with its pinmux.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200311191517.8221-4-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Defines VBUS detect and VBUS boost for the QCS404 EVB.
Detect:
VBUS present/absent is presented to the SoC via a GPIO on the EVB. Define
the pin mapping for later use by gpio-usb-conn.
Boost:
An external regulator is used to trigger VBUS on/off via GPIO. This patch
defines the relevant GPIO in the EVB dts.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200311191517.8221-3-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
QCS404 sports HS and SS USB controllers based on dwc3 block with two HS
PHYs and one SS PHY. Add nodes for these devices and enable them for
EVB board.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200311191517.8221-2-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
"arm,armv8" compatible should only be used for software models. Replace
it with the real cpu type.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/2526d2b2907116d1bb6f7edd194226eb7e24c333.1584516925.git.amit.kucheria@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
As the domain-idle-state DT binding got converted to the json-schema, a few
minor changes were introduced. For example, the states needs to be
specified within a separate node, named domain-idle-states. Let's conform
to the updated binding.
This also silence the below errors for msm8916 from of 'make dtbs_check':
idle-states: cluster-retention:compatible:0: 'arm,idle-state' was expected
idle-states: cluster-gdhs:compatible:0: 'arm,idle-state' was expected
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200326103932.5809-2-ulf.hansson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Most of the commits are for additional hardware support and minor fixes
for existing machines for all the usual platforms: qcom, amlogic, at91,
gemini, mediatek, ti, socfpga, i.mx, layerscape, uniphier, rockchip,
exynos, ux500, mvebu, tegra, stm32, renesas, sunxi, broadcom, omap,
and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation.
Andre Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into
dts files, for many devices that relied on a mix of auxiliary data
in addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants, along
with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based on
the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=ye2F
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"Most of the commits are for additional hardware support and minor
fixes for existing machines for all the usual platforms: qcom,
amlogic, at91, gemini, mediatek, ti, socfpga, i.mx, layerscape,
uniphier, rockchip, exynos, ux500, mvebu, tegra, stm32, renesas,
sunxi, broadcom, omap, and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation. Andre
Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into dts
files, for many devices that relied on a mix of auxiliary data in
addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants,
along with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based
on the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner
A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner
A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13"
* tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (520 commits)
ARM: dts: ux500: Fix missing node renames
arm64: dts: Revert "specify console via command line"
MAINTAINERS: Update Calxeda Highbank maintainership
arm: dts: calxeda: Group port-phys and sgpio-gpio items
arm: dts: calxeda: Fix interrupt grouping
arm: dts: calxeda: Provide UART clock
arm: dts: calxeda: Basic DT file fixes
arm64: dts: specify console via command line
ARM: dts: at91: sama5d27_wlsom1_ek: add USB device node
ARM: dts: gemini: Add thermal zone to DIR-685
ARM: dts: gemini: Rename IDE nodes
ARM: socfpga: arria10: Add ptp_ref clock to ethernet nodes
arm64: dts: ti: k3-j721e-mcu: add scm node and phy-gmii-sel nodes
arm64: dts: ti: k3-am65-mcu: add phy-gmii-sel node
arm64: dts: ti: k3-am65-mcu: Add DMA entries for ADC
arm64: dts: ti: k3-am65-main: Add DMA entries for main_spi0
arm64: dts: ti: k3-j721e-mcu-wakeup: Add DMA entries for ADC
arm64: dts: ti: k3-am65: Add clocks to dwc3 nodes
arm64: dts: meson-g12b-odroid-n2: add SPIFC controller node
arm64: dts: khadas-vim3: add SPIFC controller node
...
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and some
vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXoHT8w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl3CwCgj/97IKb4K49nV2rDgiV+t/ELWqUAnjBp+Zpd
H2BEdhwCFhq/5CJHKXWH
=JTm1
-----END PGP SIGNATURE-----
Merge tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and
some vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues"
* tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (161 commits)
serial: 8250: Optimize irq enable after console write
serial: 8250: Fix rs485 delay after console write
vt: vt_ioctl: fix use-after-free in vt_in_use()
vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use virtual console
tty: serial: make SERIAL_SPRD depend on COMMON_CLK
tty: serial: fsl_lpuart: fix return value checking
tty: serial: fsl_lpuart: move dma_request_chan()
ARM: dts: tango4: Make /serial compatible with ns16550a
ARM: dts: mmp*: Make the serial ports compatible with xscale-uart
ARM: dts: mmp*: Fix serial port names
ARM: dts: mmp2-brownstone: Don't redeclare phandle references
ARM: dts: pxa*: Make the serial ports compatible with xscale-uart
ARM: dts: pxa*: Fix serial port names
ARM: dts: pxa*: Don't redeclare phandle references
serial: omap: drop unused dt-bindings header
serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs
serial: 8250: 8250_omap: Work around errata causing spurious IRQs with DMA
serial: 8250: 8250_omap: Extend driver data to pass FIFO trigger info
serial: 8250: 8250_omap: Move locking out from __dma_rx_do_complete()
serial: 8250: 8250_omap: Account for data in flight during DMA teardown
...
-----BEGIN PGP SIGNATURE-----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=Ve8R
-----END PGP SIGNATURE-----
Merge tag 'media/v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- New sensor driver: imx219
- Support for some new pixelformats
- Support for Sun8i SoC
- Added more codecs to meson vdec driver
- Prepare for removing the legacy usbvision driver by moving it to
staging. This driver has issues and use legacy core APIs. If nobody
steps up to address those, it is time for its retirement.
- Several cleanups and improvements on drivers, with the addition of
new supported boards
* tag 'media/v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (236 commits)
media: venus: firmware: Ignore secure call error on first resume
media: mtk-vpu: load vpu firmware from the new location
media: i2c: video-i2c: fix build errors due to 'imply hwmon'
media: MAINTAINERS: add myself to co-maintain Hantro G1/G2 for i.MX8MQ
media: hantro: add initial i.MX8MQ support
media: dt-bindings: Document i.MX8MQ VPU bindings
media: vivid: fix incorrect PA assignment to HDMI outputs
media: hantro: Add linux-rockchip mailing list to MAINTAINERS
media: cedrus: h264: Fix 4K decoding on H6
media: siano: Use scnprintf() for avoiding potential buffer overflow
media: rc: Use scnprintf() for avoiding potential buffer overflow
media: allegro: create new struct for channel parameters
media: allegro: move mail definitions to separate file
media: allegro: pass buffers through firmware
media: allegro: verify source and destination buffer in VCU response
media: allegro: handle dependency of bitrate and bitrate_peak
media: allegro: read bitrate mode directly from control
media: allegro: make QP configurable
media: allegro: make frame rate configurable
media: allegro: skip filler data if possible
...
For the devicetree files, there are a total of 20 patches, almost
entirely for 32-bit machines:
- The Allwinner/sun9i r40 SoC dtsi file contains a number of issues,
both for correctness and for style that are addressed in separate
patches. This causes most of the changed lines of the DT updates
this time.
- More Allwinner updates fixing the identification of the security
system on sun8i/A33, a recent regression of the A83t ethernet, and a
few board specific issues on the TBS-A711 macine.
- Several bug fixes for OMAP dts files, most notably fixing the timings
for the NAND flash on the Nokia N900 that regressed a while ago after
the move to configuring them from DT. Some other OMAPs now set the
correct dma limits on the L3 bus, and a regression fix addresses lost
Ethernet on dm814x
- One incorrect setting in the newly added Raspberry Pi Zero W that
may cause issues with the SD card controller.
- A missing property on the bcm2835 firmware node caused incorrect
DMA settings.
- An old bug on the oxnas platform causing spurious interrupts is
finally addressed.
- A regression on the Exynos Midas board broke the OLED panel
power supply.
- The i.MX6 phycore SoM specified the wrong voltage for the SoC,
this is now set to the values from the datasheet.
- Some 64-bit machines use a deprecated string to identify the PSCI
firmware.
There are also several small code fixes addressing mostly serious
issues:
- Fix the sunxi rsb bus access to no longer return incorrect data when
mixing 8 and 16 bit I/O.
- Fix a suspend/resume regression on the OMAP2+ lcdc from a missing
quirk in the ti-sysc driver
- Fix a NULL pointer access from a race in the fsl dpio driver
- Fix a v5.5 regression in the exynos-chipid driver that caused an
invalid error code probing the device on non-exynos platforms
- Fix an out-of-bounds access in the AMD TEE driver
-----BEGIN PGP SIGNATURE-----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=31+Z
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM DT and driver fixes from Arnd Bergmann:
"For the devicetree files, there are a total of 20 patches, almost
entirely for 32-bit machines:
- The Allwinner/sun9i r40 SoC dtsi file contains a number of issues,
both for correctness and for style that are addressed in separate
patches. This causes most of the changed lines of the DT updates
this time.
- More Allwinner updates fixing the identification of the security
system on sun8i/A33, a recent regression of the A83t ethernet, and
a few board specific issues on the TBS-A711 macine.
- Several bug fixes for OMAP dts files, most notably fixing the
timings for the NAND flash on the Nokia N900 that regressed a while
ago after the move to configuring them from DT. Some other OMAPs
now set the correct dma limits on the L3 bus, and a regression fix
addresses lost Ethernet on dm814x
- One incorrect setting in the newly added Raspberry Pi Zero W that
may cause issues with the SD card controller.
- A missing property on the bcm2835 firmware node caused incorrect
DMA settings.
- An old bug on the oxnas platform causing spurious interrupts is
finally addressed.
- A regression on the Exynos Midas board broke the OLED panel power
supply.
- The i.MX6 phycore SoM specified the wrong voltage for the SoC, this
is now set to the values from the datasheet.
- Some 64-bit machines use a deprecated string to identify the PSCI
firmware.
There are also several small code fixes addressing mostly serious
issues:
- Fix the sunxi rsb bus access to no longer return incorrect data
when mixing 8 and 16 bit I/O.
- Fix a suspend/resume regression on the OMAP2+ lcdc from a missing
quirk in the ti-sysc driver
- Fix a NULL pointer access from a race in the fsl dpio driver
- Fix a v5.5 regression in the exynos-chipid driver that caused an
invalid error code probing the device on non-exynos platforms
- Fix an out-of-bounds access in the AMD TEE driver"
* tag 'arm-soc-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
soc: samsung: chipid: Fix return value on non-Exynos platforms
arm64: dts: Fix leftover entry-methods for PSCI
ARM: dts: exynos: Fix regulator node aliasing on Midas-based boards
ARM: dts: oxnas: Fix clear-mask property
ARM: dts: bcm283x: Fix vc4's firmware bus DMA limitations
ARM: dts: omap5: Add bus_dma_limit for L3 bus
ARM: dts: omap4-droid4: Fix lost touchscreen interrupts
ARM: dts: dra7: Add bus_dma_limit for L3 bus
ARM: bcm2835-rpi-zero-w: Add missing pinctrl name
ARM: dts: sun8i: a33: add the new SS compatible
dt-bindings: crypto: add new compatible for A33 SS
ARM: dts: sun8i: r40: Move SPI device nodes based on address order
ARM: dts: sun8i: r40: Fix register base address for SPI2 and SPI3
ARM: dts: sun8i: r40: Move AHCI device node based on address order
ARM: dts: imx6: phycore-som: fix arm and soc minimum voltage
soc: fsl: dpio: register dpio irq handlers after dpio create
tee: amdtee: out of bounds read in find_session()
ARM: dts: N900: fix onenand timings
bus: ti-sysc: Fix quirk flags for lcdc on am335x
ARM: dts: Fix dm814x Ethernet by changing to use rgmii-id mode
...
The TI J721E EVM base board has TI DP83867 PHY connected to external CPSW
NUSS Port 1 in rgmii-rxid mode.
Hence, add pinmux and Ethernet PHY configuration for TI j721e SoC MCU
Gigabit Ethernet two ports Switch subsystem (CPSW NUSS).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DT node for The TI J721E MCU SoC Gigabit Ethernet
subsystem (MCU CPSW NUSS).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AM654 EVM base board has TI DP83867 PHY connected to external CPSW NUSS
Port 1 in rgmii-rxid mode.
Hence, add pinmux and Ethernet PHY configuration for TI am654 SoC Gigabit
Ethernet two ports Switch subsystem (CPSW NUSS).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DT node for the TI AM65x SoC Gigabit Ethernet two ports Switch
subsystem (CPSW NUSS).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This brings initial support for the SM8250 and IPQ6018 platforms.
SDM845 gets audio, PCIe and IP-accelerator support, and the interconnect
providers are refactored. The Lenovo Yoga C630 has audio enabled and the
DB845c has PCIe, analog audio and low-speed interfaces enabled. The
SDM845 MTP has its display enabled and firmware location updated to
match linux-firmware.
SC7180 gains CPU topology and power properties. Interconnect providers,
eMMC, SD-card, multimedia clocks, display, Bluetooth, Venus are added.
Critical trip points are added as well as various fixes.
For MSM8916 FastRPC support is added, ETM power management and reserved
memory for Samsung A2015 are corrected.
MSM8996 switches to generic QMP phy driver for its UFS support. MSM8998
temporarily disables part of Coresight to boot without
clk_ignore_unused. CEQ for eMMC on QCS404 is enabled.
Fixes throughout the platforms to fix binding compliance, correct
compatibles for SDHCI nodes and add gpio-ranges.
-----BEGIN PGP SIGNATURE-----
iQJPBAABCAA5FiEEBd4DzF816k8JZtUlCx85Pw2ZrcUFAl5xpC8bHGJqb3JuLmFu
ZGVyc3NvbkBsaW5hcm8ub3JnAAoJEAsfOT8Nma3FPCgQAKMyejdATWdKWqCxBK5e
gpksHV8BTvfYcSU3S5txQzTL2pSYLK9gT1JpnVYFR4pZ2TwAjZaXx37dUa8lcMnx
iIu19znWkzczcRcy1604uKeXk5izLLowCJ20br9001A31GjXNq/N8RDJam2LFwOm
ZFfRjcKIX55EtedrNhLB4mIVXAVY8AuWpPPW4u+XKo0vYOe5y+aHKhiJWmzUmndj
PJuCfngDGs9uJTv8MPtG+XEz89iWO1CteiUCJ9kyjPrHIPNKwVffLwG9JVCWi8Mq
bbwev75OdrVfZXVdQl5a6tIjfe7d3lFOgJFgbKL/ApcSJxHnZt6z63+UOcBZC4ly
8ONl9jrEue7r6W9jJB6dBcRKu0AZFZ94H1urm6wE0IDmziNtXQbw2qtR+YaCLI3v
E9gjoeAxGscEDyDiP/JTz3j7IfGjQK2QZQBoeuxUQUUA3m8WYsHlr2zVHr3wLvvL
h8q2BYN5iJa4Gnb+h2ttiiEu1xo5/KQ8GAHzRBSv11zs1YZ6kWJo8y5SfFLX5heh
elz3dmPvmih1ESwWYdNUheUTCh/LF9r81/xrOsNi5QRMFimhziHVWNTUZwv9i2re
F/0d/52ABKYihJDPbzzri9XW9hhgAL91cSQ1hKL+Mh77kS2lUVRfB5JbQcIA6hda
wH5+ApyNVu10D++CPyLY9AAd
=vdPz
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/late
Qualcomm ARM64 DT updates for v5.7
This brings initial support for the SM8250 and IPQ6018 platforms.
SDM845 gets audio, PCIe and IP-accelerator support, and the interconnect
providers are refactored. The Lenovo Yoga C630 has audio enabled and the
DB845c has PCIe, analog audio and low-speed interfaces enabled. The
SDM845 MTP has its display enabled and firmware location updated to
match linux-firmware.
SC7180 gains CPU topology and power properties. Interconnect providers,
eMMC, SD-card, multimedia clocks, display, Bluetooth, Venus are added.
Critical trip points are added as well as various fixes.
For MSM8916 FastRPC support is added, ETM power management and reserved
memory for Samsung A2015 are corrected.
MSM8996 switches to generic QMP phy driver for its UFS support. MSM8998
temporarily disables part of Coresight to boot without
clk_ignore_unused. CEQ for eMMC on QCS404 is enabled.
Fixes throughout the platforms to fix binding compliance, correct
compatibles for SDHCI nodes and add gpio-ranges.
* tag 'qcom-arm64-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (56 commits)
arm64: dts: qcom: sdm845-mtp: Relocate remoteproc firmware
arm64: dts: sdm845: add IPA information
arm64: dts: qcom: db845c: add analog audio support
arm64: dts: qcom: sdm845: add pinctrl nodes for quat i2s
arm64: dts: qcom: c630: Enable audio support
arm64: dts: qcom: sdm845: add apr nodes
arm64: dts: qcom: sdm845: add slimbus nodes
arm64: dts: qcom: sc7180: Update reg names for SDHC
arm64: dts: qcom: qcs404: Enable CQE support for eMMC
arm64: dts: msm8916: Add fastrpc node
arm64: dts: qcom: sm8250: Add sm8250 dts file
arm64: dts: qcom: msm8998-mtp: Disable funnel 4 and 5
arm64: dts: qcom: db845c: add Low speed expansion i2c and spi nodes
arm64: dts: qcom: apq8016-sbc: Remove wrong regulator supply
arm64: dts: qcom: sc7180: Added critical trip point Thermal-zones node
arm64: dts: qcom: msm8998: Fix cpu compatible
arm64: dts: qcom: sc7180: Add OSM L3 interconnect provider
arm64: dts: qcom: sdm845: Add OSM L3 interconnect provider
arm64: dts: sc7180: Add interconnect provider DT nodes
arm64: dts: qcom: msm8996: Use generic QMP driver for UFS
...
Link: https://lore.kernel.org/r/20200318043823.GA470201@yoga
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I accidentally merged this after requesting a different solution,
reverting now.
Link: https://patchwork.kernel.org/patch/11431397/
Fixes: 2cedfe1247 ("arm64: dts: specify console via command line")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- add real time clock node
mt8173:
- mark arch timer invalid in suspend
mt8183:
- add CPU idle states
- add watchdog node
- add dynamic power coefficient and cooling cells for all CPUs
mt8516:
- add basic support for the SoC
- add basic support for the pumpkin board
-----BEGIN PGP SIGNATURE-----
iQJLBAABCAA1FiEEUdvKHhzqrUYPB/u8L21+TfbCqH4FAl50pDsXHG1hdHRoaWFz
LmJnZ0BnbWFpbC5jb20ACgkQL21+TfbCqH5Wqg/+LWQAEdCFKwCscc/t6L7J1FoI
oywTgYJe4sO8VjPQu0AiVvpgLw8lZf73+om0g5zsG04CzuZEK44vR4P3g8hZ7bhv
qpFj1YEiV7QK9dMuqDRGbSUg6gFf5zlwjHgEEhYV7GRkLV5L5IsxbUwUWRDnxtrC
p4bHbyPIy88y00IdpCSZaKP+5uTxl2K4LE1AvYOpyY9usNM2fHU8Mb6+fEpd/Ai2
9bVxM8B6a861D7fNXrbHBG13H2wZDcPS8QkTlp/IfoWQnGvj3ZaE5KfO/fbdHIJQ
xAqjZWk60RiWGDJFPFOl1uVuMxgTGcGnBXedW5UzpahdH+9HmPEElzxnt8NasNNB
17ZcJLhYnBfg5pl3FUQ7utwzC+8OaXOON6ZWvBG7avgJ2xumAM8B8hVXA6dyIjUp
RGPCqUAZj6x+yBO42YFS6BT+SbjImPc3WmdCqjpGLeueeXsLEQ55H1YkXjMMGrkx
q52avNWrUHrJrH8mJDhWN0lzW5yltzVlyUTle0g7joFX3ux5uCGnwTE14OmYyAYf
IHi2D8TCj3N1zZdp8wz4nwFzIjsc538vjS1how331azjjYC4DCMFIB6sX4kBALqV
Rss7HII6szBjKQY9wf7eDs4D5n4Gxtq1RN8tm78qVjo5NXZirLiyW4d2mn4moAM6
8eL5IcBN1/XUrDLIBjU=
=8cRs
-----END PGP SIGNATURE-----
Merge tag 'v5.6-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt
mt2712:
- add real time clock node
mt8173:
- mark arch timer invalid in suspend
mt8183:
- add CPU idle states
- add watchdog node
- add dynamic power coefficient and cooling cells for all CPUs
mt8516:
- add basic support for the SoC
- add basic support for the pumpkin board
* tag 'v5.6-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm64: dts: add RTC nodes for MT2712
arm64: dts: mediatek: add pumpkin board dts
arm64: dts: mediatek: add dtsi for MT8516
arm64: dts: mt8183: Add #cooling-cells to CPU nodes
arm64: dts: mt8183: add/update dynamic power coefficients
arm64: dts: mediatek: rename scpsys nodes to power-controller
amr64: dts: mt8183: Add watchdog node
arm64: dts: mt8173: add arm,no-tick-in-suspend in timer
arm64: dts: mt8183: Enable CPU idle-states
Link: https://lore.kernel.org/r/c512b5cb-e639-1429-64db-9c1a53378c49@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add missing clocks to dwc3 nodes on am65x (fixes USB)
- Add DMA entries for main_spi0 on am65x
- Add phy-gmii-sel nodes for both am65x and j721e (towards ethernet
support)
- Add DMA entries for ADC for both am65x and j721e
- Add MCU system control module on j721e (needed by phy-gmii-sel)
-----BEGIN PGP SIGNATURE-----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=XbCt
-----END PGP SIGNATURE-----
Merge tag 'ti-k3-soc-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux into arm/dt
Texas Instruments K3 SoC family changes for v5.7
- Add missing clocks to dwc3 nodes on am65x (fixes USB)
- Add DMA entries for main_spi0 on am65x
- Add phy-gmii-sel nodes for both am65x and j721e (towards ethernet
support)
- Add DMA entries for ADC for both am65x and j721e
- Add MCU system control module on j721e (needed by phy-gmii-sel)
* tag 'ti-k3-soc-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
arm64: dts: ti: k3-j721e-mcu: add scm node and phy-gmii-sel nodes
arm64: dts: ti: k3-am65-mcu: add phy-gmii-sel node
arm64: dts: ti: k3-am65-mcu: Add DMA entries for ADC
arm64: dts: ti: k3-am65-main: Add DMA entries for main_spi0
arm64: dts: ti: k3-j721e-mcu-wakeup: Add DMA entries for ADC
arm64: dts: ti: k3-am65: Add clocks to dwc3 nodes
Link: https://lore.kernel.org/r/4b6b7804-4bcb-07ba-5e76-6a411e1f457f@ti.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- New support for Kontron LS1028A based boards and NXP i.MX8MP EVK.
- Add Ethernet PHY reset GPIO for imx8mm-evk and imx8mq-evk board.
- Add gpio-fan, thermal and Ethernet support for imx8mq-phanbell board.
- Add SNVS clock description to pwrkey device for i.MX8 SoCs.
- A number of updates on librem5-devkit board to add audio, proximity
sensor, lsm9ds1 mount matrix support, and improve WoWWAN, DVFS, SD
devices as well.
- A series of patches from Anson Huang to update i.MX8 EVK boards
for support of I2C PCA6416, thermal, GPIO LED, OPP table etc.
- Add PCIe device nodes for LX2160A and LS1028A SoC.
- Add FSPI deivce support for LX2160A evaluation boards.
- Add EEPROM and LTC3882 regulator support for lx2160a-cex7 board.
- Other small and random updates on LS1028A and i.MX8 support.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl5xmGAUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7hcggAituxUHoAgPgEmEp7h+7C0dAkD8tL
G21IEi1xL608qIeKgVsyhPqbIze84+CrxzWhhUDJD+EUoVYwc78mGwOebDPBT+bE
U/VP0GU3oaHUOe0zApSf+4uWWHxmx2tqBut6qwgKp9h/nmXQKZ39yivAifrQgyn5
jckrN+gtGoCWLPUVF4baqUBJ7383A2gCpGsdTodNg95e903PYRDFORoez/8q4Hdo
r86YbIZca+tQxDrG00tpKgb0n0iIFsR139YTQtSjUQhzw9nRUcF2AuxtYGYl96mo
ZTyW82fLf+t9Av416cHFi8EL9DKQxVV6stSL6OCrVosll9zWoN/dTuNiOw==
=nTfu
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 DTS update for 5.7:
- New support for Kontron LS1028A based boards and NXP i.MX8MP EVK.
- Add Ethernet PHY reset GPIO for imx8mm-evk and imx8mq-evk board.
- Add gpio-fan, thermal and Ethernet support for imx8mq-phanbell board.
- Add SNVS clock description to pwrkey device for i.MX8 SoCs.
- A number of updates on librem5-devkit board to add audio, proximity
sensor, lsm9ds1 mount matrix support, and improve WoWWAN, DVFS, SD
devices as well.
- A series of patches from Anson Huang to update i.MX8 EVK boards
for support of I2C PCA6416, thermal, GPIO LED, OPP table etc.
- Add PCIe device nodes for LX2160A and LS1028A SoC.
- Add FSPI deivce support for LX2160A evaluation boards.
- Add EEPROM and LTC3882 regulator support for lx2160a-cex7 board.
- Other small and random updates on LS1028A and i.MX8 support.
* tag 'imx-dt64-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (63 commits)
arm64: dts: ls1028a: disable the felix switch by default
arm64: dts: imx8mp: Add snvs clock to powerkey
arm64: dts: imx8mn: Add snvs clock to powerkey
arm64: dts: ls1028a: Add PCIe controller DT nodes
arm64: dts: ls1028a: sl28: add support for variant 2
arm64: dts: ls1028a: sl28: expose switch ports in KBox A-230-LS
arm64: dts: ls1028a: sl28: fix on-board EEPROMS
arm64: dts: freescale: sl28: add SPI flash
arm64: dts: imx8m: fix aips dts node
arm64: dts: imx8mn: Add CPU thermal zone support
arm64: dts: imx8mm: Add thermal zone support
arm64: dts: imx8mq-phanbell: Fix Ethernet PHY post-reset duration
arm64: dts: enable fspi in imx8mm dts
arm64: dts: imx8mn: align name for crypto child nodes
arm64: dts: lx2160aqds: Add FSPI node properties
arm64: dts: lx2160ardb: Update FSPI node properties
arm64: dts: imx8mq-phanbell: Add gpio-fan/thermal support
arm64: dts: layerscape: add iommu-map property to pci nodes
arm64: dts: imx8mp-evk: Enable pca6416 on i2c3 bus
arm64: dts: imx8mp-evk: Add i2c3 support
...
Link: https://lore.kernel.org/r/20200318051918.32579-5-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
