The OMAP HSMMC driver has some elaborate and hairy handling for
passing GPIO card detect and write protect lines from a boardfile
into the driver: the machine defines a struct omap2_hsmmc_info
that is copied into struct omap_hsmmc_platform_data by
omap_hsmmc_pdata_init() in arch/arm/mach-omap2/hsmmc.c.
However the .gpio_cd and .gpio_wp fields are not copied from
omap2_hsmmc_info to omap_hsmmc_platform_data by
omap_hsmmc_pdata_init() so they remain unused. The only platform
defining omap2_hsmmc_info also define both to -1, unused.
It turn out there are no boardfiles passing any valid GPIO
lines into the OMAP HSMMC driver at all. And since we are not
going to add any more OMAP2 boardfiles, we can delete this
card detect and write protect handling altogether.
This seems to also fix a bug: the card detect callback
mmc_gpio_get_cd() in the slot GPIO core needs to be called
by drivers utilizing slot GPIO. It appears the the boardfile
quirks were not doing this right, so this would only get
called for boardfiles, i.e. since no boardfile was using it,
never.
Just assign mmc_gpio_get_cd() unconditionally to omap_hsmmc_ops
.get_cd() so card detects from the device tree works.
AFAICT card detect with GPIO lines assigned from
mmc_of_parse() are not working at the moment, but that is
no regression since it probably never worked.
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cover detection appears to be a feature protecting the SD
card on mobile phones with a slide-cover, such as some Nokia
phones. The idea seems to be to not allow access to the
SD card when the cover is open.
It is only usable with platform data from board files, but
no board file in the kernel is using it, yet it takes up
a sizeable chunk of code in the OMAP HSMMC driver.
Since we do not add new board files for the OMAPs any target
that need this should anyway reimplement it properly using
the device tree, so delete this legacy code.
The driver is marked as orphan in MAINTAINERS by the way.
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sd8686 "libertas" SDIO adapter's power is controlled with WLAN_RST
and WLAN_PD pins -- pretty much the same way as sd8787. Allow building
the power sequencing driver along with the libertas Wi-Fi driver.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver is complicating things for no reason: the "cd"
GPIO can easily be retrieved from the device tree if present
using just mmc_gpiod_request_cd(), which will fetch the
descriptor from the device tree using the standard binding
just fine.
If the retrieveal is successful, we also request the IRQ.
As a result the private subdriver data can be removed
entirely.
Cc: Weijun Yang <york.yang@csr.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The platform data for the PXAv3 driver allows passing a card
detect GPIO, but this code is not used in the kernel.
In order to not encourage the use of the old global GPIO
numberspace we need to remove this.
Card detect (and write protect) GPIO can easily be added into
the driver using machine descriptor tables instead, and the
descriptor-based (gpiod) variants of the slot GPIO APIs.
Cc: Jisheng Zhang <jszhang@marvell.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver is complicating things for no reason: the "cd"
GPIO can easily be retrieved from the device tree if present
using just mmc_gpiod_request_cd(), which will fetch the
descriptor from the device tree using the standard binding
just fine.
Cc: Viresh Kumar <vireshk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All the machines using the MMCI are passing GPIOs for the
card detect and write protect using the device tree or
descriptor table (one single case, Integrator/AP IM-PD1).
Drop support for passing global GPIO numbers through
platform data, noone is using it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If hosts provides ops->adma_write_desc, we should not fall back to the
general sdhci_adma_write_desc().
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As you are already in ISR, it is unnecessary to call spin_lock_irqsave.
Signed-off-by: jun qian <hangdianqj@163.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix warning when running with CONFIG_DMA_API_DEBUG_SG=y by allocating a
device_dma_parameters structure and filling in the max segment size. The
size used is the result of a discussion with Renesas hardware engineers
and unfortunately not found in the datasheet.
renesas_sdhi_internal_dmac ee140000.sd: DMA-API: mapping sg segment
longer than device claims to support [len=126976] [max=65536]
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[wsa: simplified some logic after validating intended dma_parms life cycle
and added comment]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eMMC controller is also a new timing mode controller, but it doesn't
have the timing mode switch. It does however have signal delay and
calibration controls, typical of Allwinner MMC controllers that support
the new timing mode.
Enable the new timing mode setting for the A64 eMMC controller. This
also enables MMC HS-DDR modes, which gives higher throughput for eMMC
chips that support it, and can deliver such throughput.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Newer sunxi mmc controller variants support what they call the "new
timing mode". Support for this was implemented in two ways, according
to the hardware that was seen at the time.
The first type retained the old timing mode, and both the clock and mmc
controllers had switches to select which mode was used. Both switches
had to be set to the same setting. This variant was denoted with the
.has_timings_switch field in the sunxi_mmc_cfg structure. This hardware
is only seen on the A83T.
The second type did away with the old timing mode. The clock controller
no longer had the mode selection or clock delay setting bits. In some
cases the mmc controller retained its mode selection bit, but this
always needed to be set to the new mode, or instabilities would occur.
In a few cases, such as the A64 and H6 eMMC controller, the mode
selection bit is gone, but the controller still behaves like the new
timing mode, requiring the module clock to be double the card clock
in DDR transfer modes. This variant is denoted with the
.needs_new_timings field.
This patch adds more comments explaining the two fields, as well as
the possibly nonexistent mode switch in the mmc controller.
The .has_timings_switch is renamed to .ccu_has_timings_switch to clarify
its meaning.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds the initial support of Secure Digital Host Controller
Interface compliant controller found in some latest Spreadtrum chipsets.
This patch has been tested on the version of SPRD-R11 controller.
R11 is a variant based on SD v4.0 specification.
With this driver, R11 mmc can be initialized, can be mounted, read and
written.
Original-by: Billows Wu <billows.wu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When Host Version 4 Enable is set to 1, SDMA uses ADMA System Address
register (05Fh-058h) instead of using register (000h-004h) to indicate
its system address of data location. The register (000h-004h) is
re-assigned to 32-bit Block Count and Auto CMD23 argument, so then SDMA
may use Auto CMD23.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As SD Host Controller Specification v4.10 documents:
Host Controller Version 4.10 defines this "Auto CMD Auto Select" mode.
Selection of Auto CMD depends on setting of CMD23 Enable in the Host
Control 2 register which indicates whether card supports CMD23. If CMD23
Enable =1, Auto CMD23 is used and if CMD23 Enable =0, Auto CMD12 is
used. In case of Version 4.10 or later, use of Auto CMD Auto Select is
recommended rather than use of Auto CMD12 Enable or Auto CMD23
Enable.
This patch add this new mode support.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Host Controller Version 4.10 re-defines SDMA System Address register
as 32-bit Block Count for v4 mode, and SDMA uses ADMA System
Address register (05Fh-058h) instead if v4 mode is enabled. Also
when using 32-bit block count, 16-bit block count register need
to be set to zero.
Since using 32-bit Block Count would cause problems for auto-cmd23,
it can be chosen via host->quirk2.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ADMA2 64-bit addressing support is divided into V3 mode and V4 mode.
So there are two kinds of descriptors for ADMA2 64-bit addressing
i.e. 96-bit Descriptor for V3 mode, and 128-bit Descriptor for V4
mode. 128-bit Descriptor is aligned to 8-byte.
For V4 mode, ADMA2 64-bit addressing is enabled via Host Control 2
register.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Fixed conflict while applying]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the SD host controller specification version 4.10, when
Host Version 4 is enabled, SDMA uses ADMA System Address register
(05Fh-058h) instead of using SDMA System Address register to
support both 32-bit and 64-bit addressing.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For SD host controller version 4.00 or later ones, there're two
modes of implementation - Version 3.00 compatible mode or
Version 4 mode. This patch introduced an interface to enable
v4 mode.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix inconsistent IS_ERR and PTR_ERR in tegra_sdhci_init_pinctrl_info,
the proper pointer to be passed as argument is 'pinctrl_state_1v8'
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rerun the pad calibration procedure before sdhci_request() if
the 100 ms recalibration interval has been exceeded.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement HS400 specific delay line calibration procedure. This is a
Tegra specific procedure and has to be performed regardless whether
enhanced strobe or HS400 tuning is used.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Parse and program the HS400 DQS trim value from DT. Program a fallback
value in case the property is missing.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement tegra210_sdhci_writew() to disable card clock and issue a
reset when the tuning command is sent. This is done to prevent an
intermittent hang with around 10 % failure rate during tuning.
Add tegra186_sdhci_ops because this workaround is specific to Tegra210.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tegra_sdhci_writew() defers the write to SDHCI_TRANSFER_MODE until
SDHCI_COMMAND is written. This is not necessary on Tegra210 and Tegra186
and it breaks read-modify-write operations on SDHCI_TRANSFER_MODE
because writes to SDHCI_TRANSFER_MODE aren't visible until SDHCI_COMMAND
has been written to. This results in tuning failures on Tegra210.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a new sdhci_ops struct for Tegra210 and Tegra186 which doesn't
set the custom tuning callback used on previous SoC generations.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Program the outbound sampling trim value in tegra_sdhci_reset(). Unlike
the outbound tap value this does not depend on the signaling mode and
needs to be only programmed once.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set the default inbound timing adjustment tap value on reset and on
non-tunable modes.
The default tap value is not programmed on tunable modes because the
tuning sequence is used instead to determine the tap value.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add quirk to disable the card clock during configuration of the tap
value in tegra_sdhci_set_tap() and issue sdhci_reset() after value
change. This is a workaround to avoid propagation of a potential
glitch caused by setting the tap value.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set NVQUIRK_HAS_PADCALIB on Tegra210 and Tegra186 to enable automatic
pad drive strength calibration.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Run the automatic pad calibration after voltage switching if
tegra_host->pad_calib_required is set.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Parse the pad drive strength calibration offsets from the device tree.
Program the calibration offsets in accordance with the current signaling
mode.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Disable the card clock during automatic pad drive strength calibration
and re-enable it afterwards.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Automatic pad drive strength calibration is performed on a separate pad
identical to the ones used for driving the actual bus. Power on the
calibration pad during the calibration procedure and power it off
afterwards to save power.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Configure the voltage reference used by the automatic pad drive strength
calibration procedure. The value is a magic number from the TRM.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Parse the pinctrl state and nvidia,only-1-8-v properties from the device
tree. Validate the pinctrl and regulator configuration before unmasking
UHS modes. Implement pad voltage state reconfiguration in the mmc
start_signal_voltage_switch() callback. Add NVQUIRK_NEEDS_PAD_CONTROL
and add set it for Tegra210 and Tegra186.
The pad configuration is done in the mmc callback because the order of
pad reconfiguration and sdhci voltage switch depend on the voltage to
which the transition occurs.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This variable is unused now after some refactoring.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDR104, HS200 and HS400 need to check for SCC error. If SCC error is
detected, retuning is necessary.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[Niklas: update commit message]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
for (clk = 0x80000080; new_clock >= (clock << 1); clk >>= 1)
clock <<= 1;
... is too tricky, hence I replaced with
roundup_pow_of_two(divisor) >> 2
'(clk >> 22) & 0x1' is the bit test for the 1/1 divisor, but
it is not clear. 'divisor <= 1' is easier to understand.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
renesas_sdhi_clk_start() and renesas_sdhi_clk_stop() are now only
called from renesas_sdhi_set_clock(). Merge them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When using DMA, if the DMA addr spans 128MB boundary, we have to split
the DMA transfer into two so that each one doesn't exceed the boundary.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add this hook so that it can be overridden with driver specific
implementations. We also let the original sdhci_adma_write_desc()
accept &desc so that the function can set its new value. Then export
the function so that it could be reused by driver's specific
implementations.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds adma_table_cnt member to struct sdhci_host to give more
flexibility to drivers to control the ADMA table count.
Default value of adma_table_cnt is set to (SDHCI_MAX_SEGS * 2 + 1).
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow SDHCI drivers to hook code before and after sdhci_request() by
making it externally visible.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After host requests RESET_FOR_ALL action, the hardware output an
interrupt for OS and waiting for the OS to approve.
Before writing this fix, ACPI GED has handled the interrupt. But
the ACPI GED belongs to a slow process, and sometimes the handling
process time is more than 100ms(Mutex wait more than 100ms). So
drop the GED solution and add this quirk fix.
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The device specific resource can be free in free_slot after
removing host controller.
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In tuning mode of operation, when TBCTL[TB_EN] is set, eSDHC may report
one of the following errors :
1)Tuning error while running tuning operation where SYSCTL2[SAMPCLKSEL]
will not get set even when SYSCTL2[EXTN] is reset. OR
2)Data transaction error (e.g. IRQSTAT[DCE], IRQSTAT[DEBE]) during data
transaction errors.
This issue occurs when the data window sampled within eSDHC is in full
cycle. So, in that case, eSDHC is not able to find out the start and
end points of the data window and sets the sampling pointer at default
location (which is middle of the internal SD clock). If this sampling
point coincides with the data eye boundary, then it can result in the
above mentioned errors. Impact: Tuning mode of operation for SDR50,
SDR104 or HS200 speed modes may not work properly
Workaround: In case eSDHC reports tuning error or data errors in tuning
mode of operation, by add the erratum A008171 support to fix the issue.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to add tuning error codes to
judge tuning state
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Here is another TMIO MMC variant found in Socionext UniPhier SoCs.
As commit b6147490e6 ("mmc: tmio: split core functionality, DMA and
MFD glue") said, these MMC controllers use the IP from Panasonic.
However, the MMC controller in the TMIO (Toshiba Mobile IO) MFD chip
was the first upstreamed user of this IP. The common driver code
for this IP is now called 'tmio-mmc-core' in Linux although it is a
historical misnomer.
Anyway, this driver select's MMC_TMIO_CORE to borrow the common code
from tmio-mmc-core.c
Older UniPhier SoCs (LD4, Pro4, sLD8) support the external DMA engine
like renesas_sdhi_sys_dmac.c. The difference is UniPhier SoCs use a
single DMA channel whereas Renesas chips request separate channels for
RX and TX.
Newer UniPhier SoCs (Pro5 and later) support the internal DMA engine
like renesas_sdhi_internal_dmac.c The register map is almost the same,
so I guess Renesas and Socionext use the same internal DMA hardware.
The main difference is, the register offsets are doubled for Renesas.
Renesas Socionext
SDHI UniPhier
DM_CM_DTRAN_MODE 0x820 0x410
DM_CM_DTRAN_CTRL 0x828 0x414
DM_CM_RST 0x830 0x418
DM_CM_INFO1 0x840 0x420
DM_CM_INFO1_MASK 0x848 0x424
DM_CM_INFO2 0x850 0x428
DM_CM_INFO2_MASK 0x858 0x42c
DM_DTRAN_ADDR 0x880 0x440
DM_DTRAN_ADDREX --- 0x444
This comes from the difference of host->bus_shift; 2 for Renesas SoCs,
and 1 for UniPhier SoCs. Also, the datasheet for UniPhier SoCs defines
DM_DTRAN_ADDR and DM_DTRAN_ADDREX as two separate registers.
It could be possible to factor out the DMA common code by introducing
some hooks to cope with platform quirks, but this patch does not touch
that for now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tmio_mmc_set_clock() is full of quirks because different SoC vendors
extended this in different ways.
The original IP defines the divisor range 1/2 ... 1/512.
bit 7 is set: 1/512
bit 6 is set: 1/256
...
bit 0 is set: 1/4
all bits clear: 1/2
It is platform-dependent how to achieve the 1/1 clock.
I guess the TMIO-MFD variant uses the clock selector outside of this IP,
as far as I see tmio_core_mmc_clk_div() in drivers/mfd/tmio_core.c
I guess bit[7:0]=0xff is Renesas-specific extension.
Socionext (and Panasonic) uses bit 10 (CLKSEL) for 1/1. Also, newer
versions of UniPhier SoC variants use bit 16 for 1/1024.
host->clk_update() is only used by the Renesas variants, whereas
host->set_clk_div() is only used by the TMIO-MFD variants.
To cope with this mess, promote tmio_mmc_set_clock() to a new
platform hook ->set_clock(), and melt the old two hooks into it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tmio_mmc_clk_stop(host) is equivalent to tmio_mmc_set_clock(host, 0).
This replacement is needed for the next commit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The JZ4725B is the first JZ SoC version that introduced a 32-bit IMASK
register, not the JZ4750.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I've successfully tested eMMC on the V3H Starter Kit board and since the
R8A77970 SoC has a single SDHI core, it can't be a subject to the known RX
DMA errata.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Remove the stray underscore in the DM_CM_DTRAN_MODE.BUS_WIDTH register
field name and fix the typo in the comment of the #define
DTRAN_MODE_CH_NUM_CH1.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Depending on MACH_JZ4740 | MACH_JZ4780 prevent us from creating a generic
kernel that works on more than one MIPS board. Instead, we just depend on
MIPS being set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable access to the RPMB on the on-board eMMC of the
Poplar board.
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need r8a774a1 to be whitelisted for SDHI to work on the RZ/G2M,
but we don't care about the revision of the SoC, so just whitelist
the generic part number.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When mmc-pwrseq property is passed mmc_pwrseq_alloc() can return
-EPROBE_DEFER because driver for power sequence provider is not probed
yet. Do not show error message when this situation happens.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add ACPI support to all IPROC SDHCI variants.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Convert DT properties to generic device properties
so that drivers can get properties from DT or ACPI.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Going primarily by:
https://en.wikipedia.org/wiki/List_of_Intel_Atom_microprocessors
with additional information gleaned from other related pages; notably:
- Bonnell shrink was called Saltwell
- Moorefield is the Merriefield refresh which makes it Airmont
The general naming scheme is: FAM6_ATOM_UARCH_SOCTYPE
for i in `git grep -l FAM6_ATOM` ; do
sed -i -e 's/ATOM_PINEVIEW/ATOM_BONNELL/g' \
-e 's/ATOM_LINCROFT/ATOM_BONNELL_MID/' \
-e 's/ATOM_PENWELL/ATOM_SALTWELL_MID/g' \
-e 's/ATOM_CLOVERVIEW/ATOM_SALTWELL_TABLET/g' \
-e 's/ATOM_CEDARVIEW/ATOM_SALTWELL/g' \
-e 's/ATOM_SILVERMONT1/ATOM_SILVERMONT/g' \
-e 's/ATOM_SILVERMONT2/ATOM_SILVERMONT_X/g' \
-e 's/ATOM_MERRIFIELD/ATOM_SILVERMONT_MID/g' \
-e 's/ATOM_MOOREFIELD/ATOM_AIRMONT_MID/g' \
-e 's/ATOM_DENVERTON/ATOM_GOLDMONT_X/g' \
-e 's/ATOM_GEMINI_LAKE/ATOM_GOLDMONT_PLUS/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: dave.hansen@linux.intel.com
Cc: len.brown@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=dMl4
-----END PGP SIGNATURE-----
Merge tag 'v4.19-rc6' into for-4.20/block
Merge -rc6 in, for two reasons:
1) Resolve a trivial conflict in the blk-mq-tag.c documentation
2) A few important regression fixes went into upstream directly, so
they aren't in the 4.20 branch.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* tag 'v4.19-rc6': (780 commits)
Linux 4.19-rc6
MAINTAINERS: fix reference to moved drivers/{misc => auxdisplay}/panel.c
cpufreq: qcom-kryo: Fix section annotations
perf/core: Add sanity check to deal with pinned event failure
xen/blkfront: correct purging of persistent grants
Revert "xen/blkfront: When purging persistent grants, keep them in the buffer"
selftests/powerpc: Fix Makefiles for headers_install change
blk-mq: I/O and timer unplugs are inverted in blktrace
dax: Fix deadlock in dax_lock_mapping_entry()
x86/boot: Fix kexec booting failure in the SEV bit detection code
bcache: add separate workqueue for journal_write to avoid deadlock
drm/amd/display: Fix Edid emulation for linux
drm/amd/display: Fix Vega10 lightup on S3 resume
drm/amdgpu: Fix vce work queue was not cancelled when suspend
Revert "drm/panel: Add device_link from panel device to DRM device"
xen/blkfront: When purging persistent grants, keep them in the buffer
clocksource/drivers/timer-atmel-pit: Properly handle error cases
block: fix deadline elevator drain for zoned block devices
ACPI / hotplug / PCI: Don't scan for non-hotplug bridges if slot is not bridge
drm/syncobj: Don't leak fences when WAIT_FOR_SUBMIT is set
...
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The debounce value passed to mmc_gpiod_request_cd() function is in
microseconds, but msecs_to_jiffies() requires the value to be in
miliseconds to properly calculate the delay, so adjust the value stored
in cd_debounce_delay_ms context entry.
Fixes: 1d71926bbd ("mmc: core: Fix debounce time to use microseconds")
Fixes: bfd694d5e2 ("mmc: core: Add tunable delay before detecting card
after card is inserted")
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Update device_add_disk() to take an 'groups' argument so that
individual drivers can register a device with additional sysfs
attributes.
This avoids race condition the driver would otherwise have if these
groups were to be created with sysfs_add_groups().
Signed-off-by: Martin Wilck <martin.wilck@suse.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The debounce value in device tree is in milliseconds but needs to be in
microseconds for mmc_gpiod_request_cd().
Fixes: bfd694d5e2 ("mmc: core: Add tunable delay before detecting card
after card is inserted")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to make use of array info obtained from gpiod_get_array() and
speed up processing of arrays matching single GPIO chip layout, that
information must be passed to get/set array functions. Extend the
functions' API with that additional parameter and update all users.
Pass NULL if a user builds an array itself from single GPIOs.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most users of get/set array functions iterate consecutive bits of data,
usually a single integer, while processing array of results obtained
from, or building an array of values to be passed to those functions.
Save time wasted on those iterations by changing the functions' API to
accept bitmaps.
All current users are updated as well.
More benefits from the change are expected as soon as planned support
for accepting/passing those bitmaps directly from/to respective GPIO
chip callbacks if applicable is implemented.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new of_get_compatible_child() helper to lookup the slot child
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the node of the device being probed).
While at it, also fix up the related slot-node reference leak.
Fixes: ed80a13bb4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Cc: stable <stable@vger.kernel.org> # 4.15
Cc: Carlo Caione <carlo@endlessm.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
after unbinding mmc I get things like this:
[ 185.294067] mmc1: card 0001 removed
[ 185.305206] omap_hsmmc 480b4000.mmc: wake IRQ with no resume: -13
The wakeirq stays in /proc-interrupts
rebinding shows this:
[ 289.795959] genirq: Flags mismatch irq 112. 0000200a (480b4000.mmc:wakeup) vs. 0000200a (480b4000.mmc:wakeup)
[ 289.808959] omap_hsmmc 480b4000.mmc: Unable to request wake IRQ
[ 289.815338] omap_hsmmc 480b4000.mmc: no SDIO IRQ support, falling back to polling
That bug seems to be introduced by switching from devm_request_irq()
to generic wakeirq handling.
So let us cleanup at removal.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Fixes: 5b83b2234b ("mmc: omap_hsmmc: Change wake-up interrupt to use generic wakeirq")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I have encountered an interrupt storm during the eMMC chip probing (and
the chip finally didn't get detected). It turned out that U-Boot left
the SDHI DMA interrupts enabled while the Linux driver didn't use those.
Masking those interrupts in renesas_sdhi_internal_dmac_request_dma() gets
rid of both issues...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: 2a68ea7896 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The DM_CM_RST register actually has bits 0-31 defaulting to 1s and bits
32-63 defaulting to 0s -- fix off-by-one in #define RST_RESERVED_BITS.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: 2a68ea7896 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc block driver does not support parallel dispatch of requests. In
normal circumstances, all requests are anyway funneled through a single
work item, so parallel dispatch never happens. However it can happen if
there is no elevator.
Fix that by detecting if a dispatch is in progress and returning busy
(BLK_STS_RESOURCE) in that case
Fixes: 81196976ed ("mmc: block: Add blk-mq support")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The conversion to sg_copy_{from,to}_buffer has been done in the wrong
way. sg_copy_to_buffer is a copy from an SG list to a linear buffer so
it can't replace memcpy(dest, host->virt_base, data->sg->length) where
dest is the virtual address of the SG. Same for sg_copy_from_buffer
but in the opposite way.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Suggested-by: Douglas Gilbert <dgilbert@interlog.com>
Fixes: 53d7e098ba ("mmc: android-goldfish: use sg_copy_{from,to}_buffer")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The conversion to sg_copy_{from,to}_buffer has been done in the wrong
way. sg_copy_to_buffer is a copy from an SG list to a linear buffer so
it can't replace memcpy(buf + offset, &value, remaining) where buf is
the virtual address of the SG. Same for sg_copy_to_buffer but in the
opposite way.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Suggested-by: Douglas Gilbert <dgilbert@interlog.com>
Fixes: 5b4277814e ("mmc: atmel-mci: use sg_copy_{from,to}_buffer")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_select_hs400es() calls mmc_select_bus_width() which will continue
to set 4bit transfer mode if fail to set 8bit mode. The bus width
should not be set to 4bit in HS400es.
When fail to set 8bit mode, need return error directly for HS400es.
Signed-off-by: Hongjie Fang <hongjiefang@asrmicro.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When tuning each tap is issued CMD19 twice and the result of both runs
recorded in host->taps. If the result is different between the two runs
the wrong sampling clock position was selected. Fix this by merging the
two runs and only keep the result for each tap if it was good in both
sets.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the return value of mmc_send_tuning() is error other than -EILSEQ,
the tuning fails and process goes out of for_loop. The correct
processing is to judge their TAP as not good (NG) and continue.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[Niklas: update commit message]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Recent Linux versions refuse to print actual virtual kernel addresses,
to not give a hint about the location of the kernel in a randomized virtual
address space. This affects the output of the sunxi MMC controller
driver, which now produces the rather uninformative line:
[ 1.482660] sunxi-mmc 1c0f000.mmc: base:0x(____ptrval____) irq:8
Since the virtual base address is not really interesting in the first
place, let's just drop this value. The same applies to Linux' notion of
the interrupt number, which is independent from the GIC SPI number.
We have the physical address as part of the DT node name, which is way
more useful for debugging purposes.
To keep a success message in the driver, we make this purpose explicit
with the word "initialized", plus print some information that is not too
obvious and that we learned while probing the device:
the maximum request size and whether it uses the new timing mode.
So the output turns into:
[ 1.750626] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
[ 1.786699] sunxi-mmc 1c11000.mmc: initialized, max. request size: 2048 KB
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some Allwinner boards feature an on-board eMMC with fixed 3.3V voltage
(e.g. Banana Pi M2+), and in this case both the eMMC and the SoC are
capable of doing 3.3V DDR transmission.
Add capability of 3.3V DDR when DDR is available (extra clock or new
timing).
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a first step to improve the variant specific code for mmci, add a
->dma_setup() callback to the struct mmci_host_ops.
To show its use, let's deploy the callback for the qcom dml, which involves
also to the assign the mmci_host_ops pointer from the variant ->init()
callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
To be able to better support different mmci variants, we need to be able to
use variant specific callbacks, rather than continue to sprinkle the code
with additional variant data. To move in this direction, let's add an
optional ->init() callback to the variant data struct, which variants shall
use to assign the mmci_host_ops pointer.
Using an ->init() callback enables us to partition the code between
different files. To allow separate mmci variant files to implement the
variant specifics, let's also move the definition of the struct
variant_data to the common mmci header file.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tegra SDHCI controllers require the SDHCI clock divider to be configured
to divide the clock by two in DDR50/52 modes. Incorrectly configured
clock divider results in corrupted data.
Prevent the possibility of incorrectly calculating the divider value due
to clock rate rounding or low parent clock frequency by not assigning
host->max_clk to clk_get_rate() on tegra_sdhci_set_clock().
See the comments for further details.
Fixes: a8e326a ("mmc: tegra: implement module external clock change")
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add MSI interrupt support if the SD host device can support MSI interrupt.
Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Export sdhci tuning function symbols which are used by other SD Host
controller driver modules.
Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
O2 SD Host HS200 mode clock frequency current is 208MHz, should be changed
to 200MHz to meet specification.
Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When use eMMC as boot device, the eMMC signaling voltage is tied to 1.8v
fixed output voltage, bios can set o2 sd host controller PCI configuration
register 0x308 bit4 to 1 to let driver skip 3.3v signaling voltage and
direct use 1.8v singling voltage in eMMC initialize process.
Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement and use tegra_sdhci_get_max_clock() which returns the true
maximum host clock rate. The issue with tegra_sdhci_get_max_clock() is
that it returns the current clock rate of the host instead of the
maximum one, which can lead to unnecessarily small clock rates.
This differs from the previous implementation of
tegra_sdhci_get_max_clock() in that it doesn't divide the result by two.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
