On i386 randconfig:
sound/soc/codecs/wm9705.o: In function `wm9705_soc_resume':
wm9705.c:(.text+0x128): undefined reference to `snd_ac97_reset'
sound/soc/codecs/wm9712.o: In function `wm9712_soc_resume':
wm9712.c:(.text+0x2d1): undefined reference to `snd_ac97_reset'
sound/soc/codecs/wm9713.o: In function `wm9713_soc_resume':
wm9713.c:(.text+0x820): undefined reference to `snd_ac97_reset'
Fix this by adding the missing dependencies on SND_SOC_AC97_BUS.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20200224112537.14483-1-geert@linux-m68k.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add decimation filter selection support.
Per Section 8.3.6.7 the Digital Decimation Filter is selectable between
a Linear Phase, Low Latency, and Ultra Low Latency filer.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200221181358.22526-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The TLV320ADCx140 parts support Dynamic Range Enhancer (DRE) as defined
in Section 8.3.2 of the data sheets.
The DRE achieves a complete-channel dynamic range as high as 120 dB.
At a system level, the DRE scheme enables far-field, high-fidelity recording
of audio signals in very quiet environments and low-distortion recording in
loud environments.
There are 2 enables for DRE. The first is a global setting that enables
the DRE engine in the device and the other enable is per channel. If
the DRE is enabled globally then either DRE or AGC can be used per each
configured channel. If global DRE is disabled then even setting the DRE
enable bit in the channel config register will have no effect.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200221181358.22526-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for digital volume control. There is no dedicated register
for volume control but instead there are 4. The values of the registers
are determined with exponential floating point math.
So a table was created with register values for 2dB step increments
from -110dB to 0dB.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200221124151.8774-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the tlv320adcx140 codec driver family.
The TLV320ADCx140 is a Burr-Brown™ highperformance, audio analog-to-digital
converter (ADC) that supports simultaneous sampling of up to four analog
channels or eight digital channels for the pulse density modulation (PDM)
microphone input. The device supports line and microphone inputs, and
allows for both single-ended and differential input configurations.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200220210759.31466-3-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When we get a clock error during probe we have to call
regulator_bulk_disable before bailing out, otherwise we trigger
a warning in regulator_put.
Fix this by using "goto err" like in the error cases above.
Fixes: 5a3af12931 ("ASoC: pcm512x: Add PCM512x driver")
Signed-off-by: Matthias Reichl <hias@horus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200220202956.29233-1-hias@horus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The RK3328 reference design uses an external line driver IC as a buffer
on the analog codec output, enabled by the GPIO_MUTE pin, and such a
configuration is currently assumed in the codec driver's direct poking
of GRF_SOC_CON10 to control the GPIO_MUTE output value. However, some
boards wire up analog audio yet use that pin for some other purpose, so
that assumption doesn't always hold. Update this functionality to rely
on an explicit GPIO descriptor, such that it can be managed at the
board level.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/5bc383ed1832f0f5d1dcb3c97ad92fd68e5217e3.1581376744.git.robin.murphy@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add additional support for ISENSE and VSENSE feature for the TAS2562.
This feature monitors the output to the loud speaker attempts to
eliminate IR drop errors due to packaging.
This feature is defined in Section 8.4.5 IV Sense of the data sheet.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200219134622.22066-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DAI has playback_active and capture_active to care usage count.
OTOH, we have SNDRV_PCM_STREAM_PLAYBACK/CAPTURE.
But because of this kind of implementation mismatch,
ALSA SoC has many verbose code.
To solve this issue, this patch merge playback_active/capture_active
into stream_active[2];
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/875zg5botu.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a need to use RT5682 as DAI clock master for other codecs
within a platform, which means that the DAI clocks are required to
remain, regardless of whether the RT5682 is actually running
playback/capture.
The RT5682 CCF basic functions are implemented almost by the existing
internal functions and asoc apis. It needs a clk provider (rt5682 mclk)
to generate the bclk and wclk outputs.
The RT5682 CCF supports and restricts as below:
1. Fmt of DAI-AIF1 must be configured to master before using CCF.
2. Only accept a 48MHz clk as the clk provider.
3. Only provide a 48kHz wclk and a set of multiples of wclk as bclk.
There are some temporary limitations in this patch until a better
implementation.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Link: https://lore.kernel.org/r/1582033912-6841-1-git-send-email-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the bitwidth passed in to the set_bitwidth function is not supported
then return an error.
Fixes: 29b74236bd57 ("ASoC: tas2562: Introduce the TAS2562 amplifier")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200218185252.26290-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A few fixes sent in since the merge window, none of them with global
impact but all important for the users they affect.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl5L1EQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0PeSB/9iL7rCZE89d15gmjrLzLvBFp1zXlIZ
l67F6e0RN8kw4/Au1T8noa3hzuvP7hAr0rd3dhNsFKzi0JMkPTpxA17H0qbbClSy
S7aS6Kg85thzZ51xNIw8LrzfWwI+QRMJJDLPsLET552/An36QVz+XeeMRnxkIJl5
toIAF0Ij14EH/57Sl56JRaYIkNfyBy9Nf1ilI9CDIoclE9cyT7tFvKabBDjFclOJ
bkpvP0fR1rFA0VHU/4Asc6zOj7gFMTOFkZs0Nhuuzq2FB+mtGrvvTMfR3xoaBY7P
qHnnBkBiEIXj1frMA2Ar6AJqOIuEPg8bju36k4sugeDZ/Nq7ywPkr0Ml
=m9Gm
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.6-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.6
A few fixes sent in since the merge window, none of them with global
impact but all important for the users they affect.
Reverts commit 62d5ae4caf ("ASoC: max98090: save and restore
SHDN when changing sensitive registers").
A critical side-effect was observed: when keep playing something,
the recorded sound has chance to break (clipping).
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20200214105744.82258-2-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some machine may share the same I2S lines for multiple codecs. For
example, mediatek/mt8183/mt8183-da7219-max98357 shares the same lines
between max98357a and da7219. When writing audio data through the I2S
lines, all codecs on the lines would try to generate sound if they
accepts DO line. As a result, multiple codecs generate sound at a
time.
Moves control of SD_MODE to DAPM so that machine drivers have chances
to manipulate DAPM widget to turn on/off max98357a.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20200212124608.1.I73b26b5e319de173d05823e79f5861bf1826261c@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200211200549.GA12072@embeddedor
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/wcd934x.c: In function wcd934x_codec_hphdelay_lutbypass:
sound/soc/codecs/wcd934x.c:3395:6: warning: variable hph_comp_ctrl7 set but not used [-Wunused-but-set-variable]
commit da3e83f8bb ("ASoC: wcd934x: add audio routings")
involved this unused variable.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200210150421.34680-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently SND_SOC_ALL_CODECS selects the config symbols for all codec
drivers. As "select" bypasses dependencies, lots of "select" statements
need explicit dependencies, which are hard to get right, and hard to
maintain[*].
Fix this by using "imply" instead, which is a weak version of "select",
and which obeys dependencies of target symbols.
Add dependencies to invisible symbols that are currently selected only
if their dependencies are fulfilled.
[*] See e.g. commit 13426feaf4 ("ASoC: wcd934x: Add missing
COMMON_CLK dependency to SND_SOC_ALL_CODECS").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20200207091351.18133-1-geert@linux-m68k.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Variable idx is being assigned with a value that is never idx, it is
assigned a new value a couple of statements later. The assignment is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200208221529.37105-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The field "is_sdw" is used for distinguishing the driver whether is run
in soundwire mode or not. That will run the separated setting in runtime
to make sure the driver can be run with the same build between i2s mode
and soundwire mode.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Link: https://lore.kernel.org/r/980b97e1ab9c4fab8bd345ec2158f1fd@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns:
../sound/soc/codecs/wcd934x.c:1886:11: warning: address of array
'wcd->rx_chs' will always evaluate to 'true' [-Wpointer-bool-conversion]
if (wcd->rx_chs) {
~~ ~~~~~^~~~~~
../sound/soc/codecs/wcd934x.c:1894:11: warning: address of array
'wcd->tx_chs' will always evaluate to 'true' [-Wpointer-bool-conversion]
if (wcd->tx_chs) {
~~ ~~~~~^~~~~~
2 warnings generated.
Arrays that are in the middle of a struct are never NULL so they don't
need a check like this.
Fixes: a61f3b4f47 ("ASoC: wcd934x: add support to wcd9340/wcd9341 codec")
Link: https://github.com/ClangBuiltLinux/linux/issues/854
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20200204060143.23393-1-natechancellor@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A collection of pending small fixes since the previous PR.
ALSA core:
- PCM memory leak fix
ASoC:
- Lots of SOF and Intel driver fixes
- Addition of COMMON_CLK for wcd934x
- Regression fixes for AMD and Tegra platforms
HD-audio:
- DP-MST HDMI regression fix, Tegra workarounds, HP quirk fix
Others:
- A few fixes relevant with the recent uapi-updates
- Sparse warnings and endianness fixes
-----BEGIN PGP SIGNATURE-----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=Mcey
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of pending small fixes:
ALSA core:
- PCM memory leak fix
ASoC:
- Lots of SOF and Intel driver fixes
- Addition of COMMON_CLK for wcd934x
- Regression fixes for AMD and Tegra platforms
HD-audio:
- DP-MST HDMI regression fix, Tegra workarounds, HP quirk fix
Others:
- A few fixes relevant with the recent uapi-updates
- Sparse warnings and endianness fixes"
* tag 'sound-fix-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (35 commits)
ALSA: hda: Clear RIRB status before reading WP
ALSA: hda/realtek - Fixed one of HP ALC671 platform Headset Mic supported
ASoC: wcd934x: Add missing COMMON_CLK dependency to SND_SOC_ALL_CODECS
ALSA: hda - Fix DP-MST support for NVIDIA codecs
ASoC: wcd934x: Add missing COMMON_CLK dependency
MAINTAINERS: Remove the Bard Liao from the MAINTAINERS of Realtek CODECs
ASoC: tegra: Revert 24 and 32 bit support
ASoC: SOF: Intel: add PCI ID for JasperLake
ALSA: hdsp: Make the firmware loading ioctl a bit more readable
ALSA: emu10k1: Fix annotation and cast for the recent uapi header change
ALSA: dummy: Fix PCM format loop in proc output
ALSA: usb-audio: Annotate endianess in Scarlett gen2 quirk
ALSA: usb-audio: Fix endianess in descriptor validation
ALSA: hda: Add JasperLake PCI ID and codec vid
ALSA: pcm: Fix sparse warnings wrt snd_pcm_state_t
ALSA: pcm: Fix memory leak at closing a stream without hw_free
ALSA: uapi: Fix sparse warning
ASoC: rt715: Add __maybe_unused to PM callbacks
ASoC: rt711: Add __maybe_unused to PM callbacks
ASoC: rt700: Add __maybe_unused to PM callbacks
...
An incremental fix for the Qualcomm COMMON_CLK issue.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl4776ETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0JgzB/0WQ36S9WL1/waa5XonLJ+ft9kMKypd
VVVGK70AiAhCWaahYq+BgnuH38Y3oT9G3xm4PnmobDn60t4dN6o+Ga7RlYiDDIa8
TXABNgRlpdn4Dh3xtYtvI1iQ6CifWeltJ3OwLrX9oj7HvaLiua187ovDAthp+jtZ
mkuGlpsiHutpVPapUeDVnv6S+eLzpSmICpw7YV53aewprbBddoFRhNgIOevL71w9
VvlitJAXIwAoto+/r1RExjiUO6fVMuizkGuy5Mg78GK4r0w3AuphQnmD12g9ezdU
oQjin022T2hh23JNkcRPbIHO+oFVpP74rZhz7+jVj23FxweDyU7YrvNw
=b0Bf
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.6-3' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fix for v5.6
An incremental fix for the Qualcomm COMMON_CLK issue.
A collection of updates for bugs fixed since the initial pull
request, the most important one being the addition of COMMON_CLK
for wcd934x which is needed for MFD to be merged.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl46jnATHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0FfTB/9pn+BR2PZWE349/Etdj4Tb0mHO3mfG
7sptuPYCXrFRJ82HPcSIIY8nUMBP+lYciIBE4Dn09QDxwPALFuEuzcM7XmJpJIKJ
Vg9ooyYC4/59ijQJXFGR61Xaf30PcvdxE1sC3+SEt6ROn9C/whZHFzpnPJgmeFbq
LIVI2ne/QpPQ+fozvUjkr8nOrEbLIhH6DeCRKExmQ5PYnM7fO//s51HmCUOAxQwJ
FvEH2NCZwvGA43xSYeAdWfE1C3DgdEIT1VKEfeA+Va2tjwPz64mtA6xbaNW99xV6
5/ii/c1x3Yjvy+F6IAqrmwCDZWQJ+xIgy4nbNLd2V8t1alYKWz22aVOr
=qO+a
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.6-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.6
A collection of updates for bugs fixed since the initial pull
request, the most important one being the addition of COMMON_CLK
for wcd934x which is needed for MFD to be merged.
Looks like some platforms are not yet using COMMON CLK.
PowerPC allyesconfig failed with below error in next
ld: sound/soc/codecs/wcd934x.o:(.toc+0x0):
undefined reference to `of_clk_src_simple_get'
ld: sound/soc/codecs/wcd934x.o: in function `.wcd934x_codec_probe':
wcd934x.c:(.text.wcd934x_codec_probe+0x3d4):
undefined reference to `.__clk_get_name'
ld: wcd934x.c:(.text.wcd934x_codec_probe+0x438):
undefined reference to `.clk_hw_register'
ld: wcd934x.c:(.text.wcd934x_codec_probe+0x474):
undefined reference to `.of_clk_add_provider'
Add the missing COMMON_CLK dependency to fix this errors.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200204111241.6927-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the compile warnings by adding __maybe_unused to PM callbacks:
sound/soc/codecs/rt715-sdw.c:566:12: warning: ‘rt715_dev_resume’ defined but not used [-Wunused-function]
sound/soc/codecs/rt715-sdw.c:552:12: warning: ‘rt715_dev_suspend’ defined but not used [-Wunused-function]
Fixes: d1ede0641b ("ASoC: rt715: add RT715 codec driver")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200127192831.14057-5-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the compile warnings by adding __maybe_unused to PM callbacks:
sound/soc/codecs/rt711-sdw.c:504:12: warning: ‘rt711_dev_resume’ defined but not used [-Wunused-function]
sound/soc/codecs/rt711-sdw.c:490:12: warning: ‘rt711_dev_suspend’ defined but not used [-Wunused-function]
Fixes: 320b8b0d13 ("ASoC: rt711: add rt711 codec driver")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200127192831.14057-4-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the compile warnings by adding __maybe_unused to PM callbacks:
sound/soc/codecs/rt700-sdw.c:503:12: warning: ‘rt700_dev_resume’ defined but not used [-Wunused-function]
sound/soc/codecs/rt700-sdw.c:489:12: warning: ‘rt700_dev_suspend’ defined but not used [-Wunused-function]
Fixes: 7d2a5f9ae4 ("ASoC: rt700: add rt700 codec driver")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200127192831.14057-3-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the compile warnings by adding __maybe_unused to PM callbacks:
sound/soc/codecs/rt1308-sdw.c:690:12: warning: ‘rt1308_dev_resume’ defined but not used [-Wunused-function]
sound/soc/codecs/rt1308-sdw.c:676:12: warning: ‘rt1308_dev_suspend’ defined but not used [-Wunused-function]
Fixes: a87a6653a2 ("ASoC: rt1308-sdw: add rt1308 SdW amplifier driver")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200127192831.14057-2-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 08df0d9a00 ("ASoC: max98090: revert "ASoC: max98090: fix lockdep
warning"") provided a good rationale for removing separate lock for the
SHDN register access. However it restored the lockdep warning during the
system boot. To silence the lockdep warning, mark the mutex taken in the
max98090_shdn_save() function with the lockdep class dedicated for the
runtime DAPM operations: SND_SOC_DAPM_CLASS_RUNTIME. This finally fixes
the following lockdep warning observed on Exynos4412-based Odroid U3
board:
======================================================
WARNING: possible circular locking dependency detected
5.5.0-rc7-next-20200123 #7329 Not tainted
------------------------------------------------------
alsactl/1105 is trying to acquire lock:
ed4f7cf4 (&card->dapm_mutex){+.+.}, at: max98090_shdn_save+0x1c/0x28
but task is already holding lock:
edb8d49c (&card->controls_rwsem){++++}, at: snd_ctl_ioctl+0xcc/0xbb8
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&card->controls_rwsem){++++}:
snd_ctl_add_replace+0x3c/0x84
dapm_create_or_share_kcontrol+0x24c/0x2e0
snd_soc_dapm_new_widgets+0x308/0x594
snd_soc_bind_card+0x834/0xa94
devm_snd_soc_register_card+0x34/0x6c
odroid_audio_probe+0x288/0x34c
platform_drv_probe+0x6c/0xa4
really_probe+0x200/0x48c
driver_probe_device+0x78/0x1f8
bus_for_each_drv+0x74/0xb8
__device_attach+0xd4/0x16c
bus_probe_device+0x88/0x90
deferred_probe_work_func+0x3c/0xd0
process_one_work+0x230/0x7bc
worker_thread+0x44/0x524
kthread+0x130/0x164
ret_from_fork+0x14/0x20
0x0
-> #0 (&card->dapm_mutex){+.+.}:
lock_acquire+0xe8/0x270
__mutex_lock+0x9c/0xb18
mutex_lock_nested+0x1c/0x24
max98090_shdn_save+0x1c/0x28
max98090_put_enum_double+0x20/0x40
snd_ctl_ioctl+0x190/0xbb8
ksys_ioctl+0x484/0xb10
ret_fast_syscall+0x0/0x28
0xbede0564
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&card->controls_rwsem);
lock(&card->dapm_mutex);
lock(&card->controls_rwsem);
lock(&card->dapm_mutex);
*** DEADLOCK ***
1 lock held by alsactl/1105:
#0: edb8d49c (&card->controls_rwsem){++++}, at: snd_ctl_ioctl+0xcc/0xbb8
stack backtrace:
CPU: 2 PID: 1105 Comm: alsactl Not tainted 5.5.0-rc7-next-20200123 #7329
Hardware name: Samsung Exynos (Flattened Device Tree)
[<c01126f0>] (unwind_backtrace) from [<c010e1e8>] (show_stack+0x10/0x14)
[<c010e1e8>] (show_stack) from [<c0b5234c>] (dump_stack+0xb4/0xe0)
[<c0b5234c>] (dump_stack) from [<c018a610>] (check_noncircular+0x1ec/0x208)
[<c018a610>] (check_noncircular) from [<c018ca2c>] (__lock_acquire+0x1210/0x25ec)
[<c018ca2c>] (__lock_acquire) from [<c018e728>] (lock_acquire+0xe8/0x270)
[<c018e728>] (lock_acquire) from [<c0b71928>] (__mutex_lock+0x9c/0xb18)
[<c0b71928>] (__mutex_lock) from [<c0b723c0>] (mutex_lock_nested+0x1c/0x24)
[<c0b723c0>] (mutex_lock_nested) from [<c086097c>] (max98090_shdn_save+0x1c/0x28)
[<c086097c>] (max98090_shdn_save) from [<c08613f8>] (max98090_put_enum_double+0x20/0x40)
[<c08613f8>] (max98090_put_enum_double) from [<c0833f20>] (snd_ctl_ioctl+0x190/0xbb8)
[<c0833f20>] (snd_ctl_ioctl) from [<c02cae14>] (ksys_ioctl+0x484/0xb10)
[<c02cae14>] (ksys_ioctl) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Exception stack(0xed331fa8 to 0xed331ff0)
...
Fixes: 08df0d9a00 ("ASoC: max98090: revert "ASoC: max98090: fix lockdep warning"")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20200123134046.9769-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Both the data and clock should be connected to both the left and right
inputs for DMIC only inputs, add the missing routes.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200122104143.16725-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The MT6660 is a boosted BTL class-D amplifier with V/I sensing.
A built-in DC-DC step-up converter is used to provide efficient
power for class-D amplifier with multi-level class-G operation.
The digital audio interface supports I2S, left-justified,
right-justified, TDM and DSP A/B format for audio in with a data
out used for chip information like voltage sense and current
sense, which are able to be monitored via DATAO through proper
Signed-off-by: Jeff Chang <jeff_chang@richtek.com>
Link: https://lore.kernel.org/r/1579153597-23286-1-git-send-email-richtek.jeff.chang@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 62d5ae4caf ("ASoC: max98090: save and restore SHDN when
changing sensitive registers SHDN bit") uses dapm_mutex to protect SHDN
bit. However, snd_soc_dapm_put_enum_double() in
max98090_dapm_put_enum_double() acquires the dapm_mutex again which
cause a deadlock.
Use snd_soc_dapm_put_enum_double_locked() instead to fix the deadlock.
Fixes: 62d5ae4caf ("ASoC: max98090: save and restore SHDN when changing sensitive registers SHDN bit")
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20200117073814.82441-4-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 2dc98af62c ("ASoC: max98090: fix lockdep warning") introduced
a helpful-less small lock: shdn_lock. Reverts the commit.
Reasons:
1. Lockdep should not be happy by either the original or current code.
From lockdep's point of view, there is a lock inversion anyway.
Let d = dapm_mutex, c = controls_rwsem, s = shdn_lock,
From the reported calling stack: lock acquisition order of
snd_soc_register_card() is: d -> c.
> snd_ctl_add_replace+0x3c/0x84
> dapm_create_or_share_kcontrol+0x24c/0x2e0
> snd_soc_dapm_new_widgets+0x308/0x594
> snd_soc_bind_card+0x80c/0xad4
> devm_snd_soc_register_card+0x34/0x6c
If calling snd_soc_dapm_put_enum_double() in kcontrol's put (e.g.
SOC_DAPM_ENUM_EXT), lock acquisition order is: c -> d. Note that,
snd_soc_dapm_put_enum_double() acquires d.
The possible lock inversion is always there if registering sound card
and putting mixer control happen at the same time. In fact, it never
happens because the control device don't show up to the userspace until
the sound card build success.
Commit 2dc98af62c ("ASoC: max98090: fix lockdep warning") changes the
order to: c -> s -> d. The lock inversion is still there.
2. Commit 62d5ae4caf ("ASoC: max98090: save and restore SHDN when
changing sensitive registers SHDN bit") designed to use dapm_mutex to
protect SHDN bit. Use a separate lock breaks the protection.
DAPM changes SHDN bit automatically when it finds the path. Thus, any
code wants to change the SHDN bit, need to acquire the dapm_mutex first.
> SND_SOC_DAPM_SUPPLY("SHDN", M98090_REG_DEVICE_SHUTDOWN,
> M98090_SHDNN_SHIFT, 0, NULL, 0),
Fixes: 2dc98af62c ("ASoC: max98090: fix lockdep warning")
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20200117073814.82441-2-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This became bigger than I have hoped for rc7. But, the only large LOC
is for stm32 fixes that are simple rewriting of register access
helpers, while the rest are all nice and small fixes:
- A few ASoC fixes for the remaining probe error handling bugs
- ALSA sequencer core fix for racy proc file accesses
- Revert the option rename of snd-hda-intel to make compatible again
- Various device-specific fixes
-----BEGIN PGP SIGNATURE-----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=M4pi
-----END PGP SIGNATURE-----
Merge tag 'sound-5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This became bigger than I have hoped for rc7. But, the only large LOC
is for stm32 fixes that are simple rewriting of register access
helpers, while the rest are all nice and small fixes:
- A few ASoC fixes for the remaining probe error handling bugs
- ALSA sequencer core fix for racy proc file accesses
- Revert the option rename of snd-hda-intel to make compatible again
- Various device-specific fixes"
* tag 'sound-5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: seq: Fix racy access for queue timer in proc read
ALSA: usb-audio: fix sync-ep altsetting sanity check
ASoC: msm8916-wcd-digital: Reset RX interpolation path after use
ASoC: msm8916-wcd-analog: Fix MIC BIAS Internal1
ASoC: cros_ec_codec: Make the device acpi compatible
ASoC: sti: fix possible sleep-in-atomic
ASoC: msm8916-wcd-analog: Fix selected events for MIC BIAS External1
ASoC: hdac_hda: Fix error in driver removal after failed probe
ASoC: SOF: Intel: fix HDA codec driver probe with multiple controllers
ASoC: SOF: Intel: lower print level to dbg if we will reinit DSP
ALSA: dice: fix fallback from protocol extension into limited functionality
ALSA: firewire-tascam: fix corruption due to spin lock without restoration in SoftIRQ context
ALSA: hda: Rename back to dmic_detect option
ASoC: stm32: dfsdm: fix 16 bits record
ASoC: stm32: sai: fix possible circular locking
ASoC: Fix NULL dereference at freeing
ASoC: Intel: bytcht_es8316: Fix Irbis NB41 netbook quirk
ASoC: rt5640: Fix NULL dereference on module unload
PM8916 has three TX inputs that each have an (optional) internal
RBIAS resistor. MIC BIAS Internal1/2 (for TX1/2) are already supported.
TX3 does not have its own MIC BIAS supply, instead it is also supplied
from MIC_BIAS1.
Now that we have simplified the MIC BIAS Internal* implementation
we can easily add support for it:
Add a MIC BIAS Internal3 supply that enables the internal RBIAS
resistor on TX3, and make sure to also enable the MIC_BIAS1 supply.
Tested-by: Nikita Travkin <nikitos.tr@gmail.com> # longcheer-l8150
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200114181229.42302-2-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
At the moment, MIC BIAS Internal* and MIC BIAS External* both reference
the same register, and have a part of their initialization sequence
duplicated.
For example, the sequence for enabling MIC BIAS Internal1 is:
I1. Enable MIC_BIAS1 supply (MICB_EN bit in CDC_A_MICB_1_EN)
I2. Enable internal RBIAS (TX1_INT_RBIAS_EN bit in CDC_A_MICB_1_INT_RBIAS)
The sequence for enabling MIC BIAS External1 is:
E1. Enable MIC_BIAS1 supply (MICB_EN bit in CDC_A_MICB_1_EN)
(E2. Ideally, make sure internal RBIAS is disabled. However, this should
not happen in practice because DAPM will disable unused supplies...)
Right now we have:
SND_SOC_DAPM_SUPPLY("MIC BIAS Internal1", CDC_A_MICB_1_EN, 7, 0, ...) // I1
SND_SOC_DAPM_SUPPLY("MIC BIAS External1", CDC_A_MICB_1_EN, 7, 0, ...) // E1
and I2 is done in the PM event handler (pm8916_wcd_analog_enable_micbias_int1).
We can simplify this by defining a common DAPM supply for I1/E1 ("MIC_BIAS1"),
and one DAPM supply for I2 ("MIC BIAS Internal1"). Additional DAPM routes
ensure that we also enable the MIC_BIAS1 supply for the internal and external
pull up resistor.
Another advantage of this is that we now disable the internal RBIAS
when it is not needed. This makes it much easier to add support for
MIC BIAS Internal3 as a next step.
Tested-by: Nikita Travkin <nikitos.tr@gmail.com> # longcheer-l8150
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200114181229.42302-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
This is mostly driver specific fixes, plus an error handling fix
in the core. There is a rather large diffstat for the stm32 SAI
driver, this is a very large but mostly mechanical update which
wraps every register access in the driver to allow a fix to the
locking which avoids circular locks, the active change is much
smaller and more reasonably sized.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl4gVcMTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0IMOB/wJszUsDT3K46IvCg0qKJhsW+vsFsuo
bjk03Fsbi/v6ukcrIbRxBl50saqut8MFibSgrMTlDCkCOvQbz3C+S2N96N9SKWSX
gfEYd6PzdxVkZCx8xqybB82WGXjNBzoJue7lIYe2ytCIwjasPZtBjfNW9E+6KNkC
zOGoRLGSDepZRovDQM8JbALhKHw4z5a19fDOGiESuDfp3kjsTKAe8R+UXRvcsIDc
mqBblGMcKOZtRw87MDlDK2iKLPJEKAS3ndr6/a8+iX02hJMb3Yu6NbMmU4/0kHfC
3xc7xoyTZW8GVnhsLchJhOBaz+TFizTqBJTCr1tjkEjPB504SZm+/Wtx
=/nsR
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl4h1RITHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0AjyB/41oCDts2pMZqxyt9PNBE3p4TDrRmxE
Ocbtn+ygKWCaqEX+Ecy8rPMtXEM1Ziz4o57+iOUWlpLd63uXDxBwF+t8+oXtbvCP
qfAO4IV7Fnw6CZTDvl5VFkSJKz+8woqP+ucqRIZSQLgqjuXXm26NVvZR93VY9av4
gdHregixNNxLk1lElp9ZKyos3FvhkAFf/Fl4oNEgAH/7mP8yj82sJPd/RQYiaeNu
t1vMC++Rh6cqt4X8gMWz8yET4LjqIWzQVMdyGJ9BP9mUtGUtuwK3kkQKpCpu1dMc
b2y1G5uUPFBT9bgIOWyPqXIqsqdBSauuD5/e1jCz2Tgeq961C47qAiBC
=khtD
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.5-rc6' into asoc-5.6
ASoC: Fixes for v5.5
This is mostly driver specific fixes, plus an error handling fix
in the core. There is a rather large diffstat for the stm32 SAI
driver, this is a very large but mostly mechanical update which
wraps every register access in the driver to allow a fix to the
locking which avoids circular locks, the active change is much
smaller and more reasonably sized.
In case of error, the function devm_regmap_init() returns ERR_PTR() and
never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().
Fixes: d1ede0641b ("ASoC: rt715: add RT715 codec driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200117024149.75515-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of error, the function devm_regmap_init() returns ERR_PTR() and
never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().
Fixes: 320b8b0d13 ("ASoC: rt711: add rt711 codec driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200115143034.94492-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of error, the function devm_regmap_init() returns ERR_PTR() and
never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().
Fixes: 7d2a5f9ae4 ("ASoC: rt700: add rt700 codec driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200115143027.94364-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The QFN package is a new one.
There is a different initial setting to the chip of QFN and WLCSP package.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20200116091854.18095-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Should the write to MADERA_OUTPUT_ENABLES_1 fail and out_clamp[0] not be
set an additional error message will be printed. Clear the ret variable
to avoid this.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200114161841.451-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Correctly link both channels on the DAC if an output muxed between a
stereo and mono output. Without this one channel of the DAC may be
erroneously powered down whilst in mono mode.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200114161841.451-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The recently added API that exposes firmware mixer controls to the
kernel is missing cache handling and all writes bypass the cache, this
obviously causes the cache to get out of sync with the hardware. Factor
out the cache handling into two new helper functions and call those from
both the normal ALSA control handlers and the new kernel API.
Fixes: eb65ccdb08 ("ASoC: wm_adsp: Expose mixer control API")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200114161841.451-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is mostly driver specific fixes, plus an error handling fix
in the core. There is a rather large diffstat for the stm32 SAI
driver, this is a very large but mostly mechanical update which
wraps every register access in the driver to allow a fix to the
locking which avoids circular locks, the active change is much
smaller and more reasonably sized.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl4gVcMTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0IMOB/wJszUsDT3K46IvCg0qKJhsW+vsFsuo
bjk03Fsbi/v6ukcrIbRxBl50saqut8MFibSgrMTlDCkCOvQbz3C+S2N96N9SKWSX
gfEYd6PzdxVkZCx8xqybB82WGXjNBzoJue7lIYe2ytCIwjasPZtBjfNW9E+6KNkC
zOGoRLGSDepZRovDQM8JbALhKHw4z5a19fDOGiESuDfp3kjsTKAe8R+UXRvcsIDc
mqBblGMcKOZtRw87MDlDK2iKLPJEKAS3ndr6/a8+iX02hJMb3Yu6NbMmU4/0kHfC
3xc7xoyTZW8GVnhsLchJhOBaz+TFizTqBJTCr1tjkEjPB504SZm+/Wtx
=/nsR
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.5-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.5
This is mostly driver specific fixes, plus an error handling fix
in the core. There is a rather large diffstat for the stm32 SAI
driver, this is a very large but mostly mechanical update which
wraps every register access in the driver to allow a fix to the
locking which avoids circular locks, the active change is much
smaller and more reasonably sized.
Support multiple endpoints on SGTL5000 codec port when used in
of_graph context.
This patch allows to share the codec port between two CPU DAIs.
Example:
Custom STM32MP157C board uses SGTL5000 audio codec. This codec is
connected to two serial audio interfaces, which are configured
either as rx or tx.
From AsoC point of view the topolgy is the following:
// 2 CPU DAIs (SAI2A/B), 1 Codec (SGTL5000)
Playback: CPU-A-DAI(slave) -> (master)CODEC-DAI/port0
Record: CPU-B-DAI(slave) <- (master)CODEC-DAI/port0
In the DT two endpoints have to be associated to the codec port:
sgtl5000_port: port {
sgtl5000_tx_endpoint: endpoint@0 {
remote-endpoint = <&sai2a_endpoint>;
};
sgtl5000_rx_endpoint: endpoint@1 {
remote-endpoint = <&sai2b_endpoint>;
};
};
However, when the audio graph card parses the codec nodes, it expects
to find DAI interface indexes matching the endpoints indexes.
The current patch forces the use of DAI id 0 for both endpoints,
which allows to share the codec DAI between the two CPU DAIs
for playback and capture streams respectively.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20191219213219.366073-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Comparing the voltage of VDDA and VDDIO to determine whether or not to
enable VDDC manual override is insufficient. This is a problem in case
the VDDA is supplied from different regulator than VDDIO, while both
report the same voltage to the regulator framework. In that case where
VDDA and VDDIO is supplied by different regulators, the VDDC manual
override must not be applied.
Fixes: b6319b061b ("ASoC: sgtl5000: Fix charge pump source assignment")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Link: https://lore.kernel.org/r/20191220164450.1395038-2-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Add jz4770-codec driver to support the internal CODEC found in the
JZ4770 SoC from Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Link: https://lore.kernel.org/r/20191224002708.1207884-2-paul@crapouillou.net
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixup this error
CC sound/soc/codecs/rt715-sdw.o
linux/sound/soc/codecs/rt715-sdw.c: In function 'rt715_dev_resume':
linux/sound/soc/codecs/rt715-sdw.c:568:28: error: implicit declaration\
of function 'to_sdw_slave_device'; did you mean 'sdw_slave_modalias'?\
[-Werror=implicit-function-declaration]
struct sdw_slave *slave = to_sdw_slave_device(dev);
^~~~~~~~~~~~~~~~~~~
sdw_slave_modalias
linux/sound/soc/codecs/rt715-sdw.c:568:28: warning: initialization of\
'struct sdw_slave *' from 'int' makes pointer from integer without a\
cast [-Wint-conversion]
cc1: some warnings being treated as errors
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87h80yhm9p.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the initial amplifier driver for rt1308-sdw.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20200110014606.17333-1-shumingf@realtek.com
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason, attempting to route audio through QDSP6 on MSM8916
causes the RX interpolation path to get "stuck" after playing audio
a few times. In this situation, the analog codec part is still working,
but the RX path in the digital codec stops working, so you only hear
the analog parts powering up. After a reboot everything works again.
So far I was not able to reproduce the problem when using lpass-cpu.
The downstream kernel driver avoids this by resetting the RX
interpolation path after use. In mainline we do something similar
for the TX decimator (LPASS_CDC_CLK_TX_RESET_B1_CTL), but the
interpolator reset (LPASS_CDC_CLK_RX_RESET_CTL) got lost when the
msm8916-wcd driver was split into analog and digital.
Fix this problem by adding the reset to
msm8916_wcd_digital_enable_interpolator().
Fixes: 150db8c5af ("ASoC: codecs: Add msm8916-wcd digital codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200105102753.83108-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
MIC BIAS Internal1 is broken at the moment because we always
enable the internal rbias resistor to the TX2 line (connected to
the headset microphone), rather than enabling the resistor connected
to TX1.
Move the RBIAS code to pm8916_wcd_analog_enable_micbias_int1/2()
to fix this.
Fixes: 585e881e5b ("ASoC: codecs: Add msm8916-wcd analog codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200111164006.43074-3-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
MIC BIAS External1 sets pm8916_wcd_analog_enable_micbias_ext1()
as event handler, which ends up in pm8916_wcd_analog_enable_micbias_ext().
But pm8916_wcd_analog_enable_micbias_ext() only handles the POST_PMU
event, which is not specified in the event flags for MIC BIAS External1.
This means that the code in the event handler is never actually run.
Set SND_SOC_DAPM_POST_PMU as the only event for the handler to fix this.
Fixes: 585e881e5b ("ASoC: codecs: Add msm8916-wcd analog codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200111164006.43074-2-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
In case system has multiple HDA codecs, and codec probe fails for
at least one but not all codecs, driver will end up cancelling
a non-initialized timer context upon driver removal.
Call trace of typical case:
[ 60.593646] WARNING: CPU: 1 PID: 1147 at kernel/workqueue.c:3032
__flush_work+0x18b/0x1a0
[...]
[ 60.593670] __cancel_work_timer+0x11f/0x1a0
[ 60.593673] hdac_hda_dev_remove+0x25/0x30 [snd_soc_hdac_hda]
[ 60.593674] device_release_driver_internal+0xe0/0x1c0
[ 60.593675] bus_remove_device+0xd6/0x140
[ 60.593677] device_del+0x175/0x3e0
[ 60.593679] ? widget_tree_free.isra.7+0x90/0xb0 [snd_hda_core]
[ 60.593680] snd_hdac_device_unregister+0x34/0x50 [snd_hda_core]
[ 60.593682] snd_hdac_ext_bus_device_remove+0x2a/0x60 [snd_hda_ext_core]
[ 60.593684] hda_dsp_remove+0x26/0x100 [snd_sof_intel_hda_common]
[ 60.593686] snd_sof_device_remove+0x84/0xa0 [snd_sof]
[ 60.593687] sof_pci_remove+0x10/0x30 [snd_sof_pci]
[ 60.593689] pci_device_remove+0x36/0xb0
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the initial codec driver for rt700.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110014552.17252-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 4e93c1294f (ASoC: max98090: fix incorrect
helper in max98090_dapm_put_enum_double()) which was misapplied.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the initial codec driver for rt711.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191227054445.27223-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support to WSA8810/WSA8815 Class-D Smart Speaker
Amplifier. This Amplifier is primarily interfaced with SoundWire.
One WSA is used for mono speaker configuration and second one
would give stereo setup.
This patch is tested on SDM845 based DragonBoard DB845c and
Lenovo YOGA C630 Laptop based on SDM850 with WSA8815
speaker amplifiers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200107135929.3267-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 62d5ae4caf ("ASoC: max98090: save and restore SHDN when changing
sensitive registers") extended the code for handling many controls by
adding a custom put function to them. That new custom put function
properly handles relations between codec's hardware registers. However
they used card->dapm_mutex to properly serialize those operations. This
in turn triggers a lockdep warning about possible circular dependency.
Fix this by introducing a separate mutex only for serializing the SHDN
hardware register related operations.
This fixes the following lockdep warning observed on Exynos4412-based
Odroid U3 board:
======================================================
WARNING: possible circular locking dependency detected
5.5.0-rc5-next-20200107 #166 Not tainted
------------------------------------------------------
alsactl/1104 is trying to acquire lock:
ed0d50f4 (&card->dapm_mutex){+.+.}, at: max98090_shdn_save+0x1c/0x28
but task is already holding lock:
edb4b49c (&card->controls_rwsem){++++}, at: snd_ctl_ioctl+0xcc/0xbb8
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&card->controls_rwsem){++++}:
snd_ctl_add_replace+0x3c/0x84
dapm_create_or_share_kcontrol+0x24c/0x2e0
snd_soc_dapm_new_widgets+0x308/0x594
snd_soc_bind_card+0x80c/0xad4
devm_snd_soc_register_card+0x34/0x6c
odroid_audio_probe+0x288/0x34c
platform_drv_probe+0x6c/0xa4
really_probe+0x200/0x490
driver_probe_device+0x78/0x1f8
bus_for_each_drv+0x74/0xb8
__device_attach+0xd4/0x16c
bus_probe_device+0x88/0x90
deferred_probe_work_func+0x3c/0xd0
process_one_work+0x22c/0x7c4
worker_thread+0x44/0x524
kthread+0x130/0x164
ret_from_fork+0x14/0x20
0x0
-> #0 (&card->dapm_mutex){+.+.}:
lock_acquire+0xe8/0x270
__mutex_lock+0x9c/0xb18
mutex_lock_nested+0x1c/0x24
max98090_shdn_save+0x1c/0x28
max98090_put_enum_double+0x20/0x40
snd_ctl_ioctl+0x190/0xbb8
ksys_ioctl+0x470/0xaf8
ret_fast_syscall+0x0/0x28
0xbefaa564
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&card->controls_rwsem);
lock(&card->dapm_mutex);
lock(&card->controls_rwsem);
lock(&card->dapm_mutex);
*** DEADLOCK ***
1 lock held by alsactl/1104:
#0: edb4b49c (&card->controls_rwsem){++++}, at: snd_ctl_ioctl+0xcc/0xbb8
stack backtrace:
CPU: 0 PID: 1104 Comm: alsactl Not tainted 5.5.0-rc5-next-20200107 #166
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
(unwind_backtrace) from [<c010e180>] (show_stack+0x10/0x14)
(show_stack) from [<c0b2a09c>] (dump_stack+0xb4/0xe0)
(dump_stack) from [<c018a1c0>] (check_noncircular+0x1ec/0x208)
(check_noncircular) from [<c018c5dc>] (__lock_acquire+0x1210/0x25ec)
(__lock_acquire) from [<c018e2d8>] (lock_acquire+0xe8/0x270)
(lock_acquire) from [<c0b49678>] (__mutex_lock+0x9c/0xb18)
(__mutex_lock) from [<c0b4a110>] (mutex_lock_nested+0x1c/0x24)
(mutex_lock_nested) from [<c0839b3c>] (max98090_shdn_save+0x1c/0x28)
(max98090_shdn_save) from [<c083a5b8>] (max98090_put_enum_double+0x20/0x40)
(max98090_put_enum_double) from [<c080d0e8>] (snd_ctl_ioctl+0x190/0xbb8)
(snd_ctl_ioctl) from [<c02cafec>] (ksys_ioctl+0x470/0xaf8)
(ksys_ioctl) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
...
Fixes: 62d5ae4caf ("ASoC: max98090: save and restore SHDN when changing sensitive registers")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200108115007.31095-2-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 62d5ae4caf ("ASoC: max98090: save and restore SHDN when changing
sensitive registers") extended the code for handling "LTENL Mux", "LTENR
Mux", "LBENL Mux" and "LBENR Mux" controls by adding a custom
max98090_dapm_put_enum_double() function to them. However that function
used incorrect helper to get its component object. Fix this by using the
proper snd_soc_dapm_* helper.
This fixes the following NULL pointer exception observed on
Exynos4412-based Odroid U3 board:
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 000000b0
pgd = (ptrval)
[000000b0] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1104 Comm: alsactl Not tainted 5.5.0-rc5-next-20200107 #166
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
PC is at __mutex_lock+0x54/0xb18
LR is at ___might_sleep+0x3c/0x2e0
...
Process alsactl (pid: 1104, stack limit = 0x(ptrval))
...
[<c0b49630>] (__mutex_lock) from [<c0b4a110>] (mutex_lock_nested+0x1c/0x24)
[<c0b4a110>] (mutex_lock_nested) from [<c0839b3c>] (max98090_shdn_save+0x1c/0x28)
[<c0839b3c>] (max98090_shdn_save) from [<c083a4f8>] (max98090_dapm_put_enum_double+0x20/0x40)
[<c083a4f8>] (max98090_dapm_put_enum_double) from [<c080d0e8>] (snd_ctl_ioctl+0x190/0xbb8)
[<c080d0e8>] (snd_ctl_ioctl) from [<c02cafec>] (ksys_ioctl+0x470/0xaf8)
[<c02cafec>] (ksys_ioctl) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
...
---[ end trace 0e93f0580f4b9241 ]---
Fixes: 62d5ae4caf ("ASoC: max98090: save and restore SHDN when changing sensitive registers")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20200108115007.31095-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 62d5ae4caf ("ASoC: max98090: save and restore SHDN when changing
sensitive registers") extended the code for handling "LTENL Mux", "LTENR
Mux", "LBENL Mux" and "LBENR Mux" controls by adding a custom
max98090_dapm_put_enum_double() function to them. However that function
used incorrect helper to get its component object. Fix this by using the
proper snd_soc_dapm_* helper.
This fixes the following NULL pointer exception observed on
Exynos4412-based Odroid U3 board:
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 000000b0
pgd = (ptrval)
[000000b0] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1104 Comm: alsactl Not tainted 5.5.0-rc5-next-20200107 #166
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
PC is at __mutex_lock+0x54/0xb18
LR is at ___might_sleep+0x3c/0x2e0
...
Process alsactl (pid: 1104, stack limit = 0x(ptrval))
...
[<c0b49630>] (__mutex_lock) from [<c0b4a110>] (mutex_lock_nested+0x1c/0x24)
[<c0b4a110>] (mutex_lock_nested) from [<c0839b3c>] (max98090_shdn_save+0x1c/0x28)
[<c0839b3c>] (max98090_shdn_save) from [<c083a4f8>] (max98090_dapm_put_enum_double+0x20/0x40)
[<c083a4f8>] (max98090_dapm_put_enum_double) from [<c080d0e8>] (snd_ctl_ioctl+0x190/0xbb8)
[<c080d0e8>] (snd_ctl_ioctl) from [<c02cafec>] (ksys_ioctl+0x470/0xaf8)
[<c02cafec>] (ksys_ioctl) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
...
---[ end trace 0e93f0580f4b9241 ]---
Fixes: 62d5ae4caf ("ASoC: max98090: save and restore SHDN when changing sensitive registers")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20200108115007.31095-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver produces warnings without CONFIG_OF, and makes
no sense without it either:
sound/soc/codecs/gtm601.c:50:34: error: 'bm818_dai' defined but not used [-Werror=unused-variable]
static struct snd_soc_dai_driver bm818_dai = {
^~~~~~~~~
sound/soc/codecs/gtm601.c:32:34: error: 'gtm601_dai' defined but not used [-Werror=unused-variable]
static struct snd_soc_dai_driver gtm601_dai = {
^~~~~~~~~~
Remove the #ifdef check to avoid the warning.
Fixes: 057a317a8d ("ASoC: gtm601: add Broadmobi bm818 sound profile")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200107214846.1284981-1-arnd@arndb.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5640->jack is NULL if jack is already disabled at the time of
driver's module unloading.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106014707.11378-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If 'madera_init_bus_error_irq()' fails,
'wm_adsp2_remove(&cs47l92->core.adsp[0])' will be called twice.
Once in the 'if' block, and once in the error handling path.
This is harmless, but one of this call can be axed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191226162907.9490-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds audio routing for both playback and capture.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20191219103153.14875-8-srinivas.kandagatla@linaro.org
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds basic controls found in wcd934x codec.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20191219103153.14875-5-srinivas.kandagatla@linaro.org
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Qualcomm WCD9340/WCD9341 Codec is a standalone Hi-Fi audio codec IC,
It supports both I2S/I2C and SLIMbus audio interfaces.
On slimbus interface it supports two data lanes; 16 Tx ports
and 8 Rx ports. It has Five DACs and seven dedicated interpolators,
Seven (six audio ADCs, and one VBAT ADC), Multibutton headset
control (MBHC), Active noise cancellation, Sidetone paths,
MAD (mic activity detection) and codec processing engine.
It supports Class-H differential earpiece out and stereo single
ended headphones out.
This codec also has integrated SoundWire controller.
This patchset adds very basic support for playback and capture
via the interpolators and ADC respectively.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20191219103153.14875-4-srinivas.kandagatla@linaro.org
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TGL supports more than three HDMI Dai's. So, update hdac_hda_dais table
to include 4th DAI.
Without this patch, we saw the below error in TGL DUT:
sof_rt5682 tgl_max98357a_rt5682: ASoC: CODEC DAI intel-hdmi-hifi4 not
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Jairaj Arava <jairaj.arava@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191220171037.10689-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A slightly high amount at this time, but all good and small fixes.
- A PCM core fix that initializes the buffer properly for avoiding
information leaks; it is a long-standing minor problem, but good
to fix better now
- A few ASoC core fixes for the init / cleanup ordering issues
that surfaced after the recent refactoring
- Lots of SOF and topology-related fixes went in, as usual as such
hot topics
- Several ASoC codec and platform-specific small fixes: wm89xx,
realtek, and max98090, AMD, Intel-SST
- A fix for the previous incomplete regression of HD-audio, now
hitting Nvidia HDMI
- A few HD-audio CA0132 codec fixes
-----BEGIN PGP SIGNATURE-----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=eyq5
-----END PGP SIGNATURE-----
Merge tag 'sound-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A slightly high amount at this time, but all good and small fixes:
- A PCM core fix that initializes the buffer properly for avoiding
information leaks; it is a long-standing minor problem, but good to
fix better now
- A few ASoC core fixes for the init / cleanup ordering issues that
surfaced after the recent refactoring
- Lots of SOF and topology-related fixes went in, as usual as such
hot topics
- Several ASoC codec and platform-specific small fixes: wm89xx,
realtek, and max98090, AMD, Intel-SST
- A fix for the previous incomplete regression of HD-audio, now
hitting Nvidia HDMI
- A few HD-audio CA0132 codec fixes"
* tag 'sound-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (27 commits)
ALSA: hda - Downgrade error message for single-cmd fallback
ASoC: wm8962: fix lambda value
ALSA: hda: Fix regression by strip mask fix
ALSA: hda/ca0132 - Fix work handling in delayed HP detection
ALSA: hda/ca0132 - Avoid endless loop
ALSA: hda/ca0132 - Keep power on during processing DSP response
ALSA: pcm: Avoid possible info leaks from PCM stream buffers
ASoC: Intel: common: work-around incorrect ACPI HID for CML boards
ASoC: SOF: Intel: split cht and byt debug window sizes
ASoC: SOF: loader: fix snd_sof_fw_parse_ext_data
ASoC: SOF: loader: snd_sof_fw_parse_ext_data log warning on unknown header
ASoC: simple-card: Don't create separate link when platform is present
ASoC: topology: Check return value for soc_tplg_pcm_create()
ASoC: topology: Check return value for snd_soc_add_dai_link()
ASoC: core: only flush inited work during free
ASoC: Intel: bytcr_rt5640: Update quirk for Teclast X89
ASoC: core: Init pcm runtime work early to avoid warnings
ASoC: Intel: sst: Add missing include <linux/io.h>
ASoC: max98090: fix possible race conditions
ASoC: max98090: exit workaround earlier if PLL is locked
...
A collection of fixes since the merge window, mostly driver specific but
there's a few in the core that clean up fallout from the refactorings
done in the last cycle.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl34w3ITHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0FM/B/9zM8zae1DIXi10S7tRElz/LnadE7il
umQ34PoghSd/f9D5TCQZMgyLjdglyQGiOar4G1xkOEC87yjBCY8AOfcV3QQLRsgK
ej8AdrBGKQUWvCdoJGx/FsrwTpgBcvRNvVJbHIKab2BfGxZA8t733tMCAkuXHnty
/dtYhA5wjI6gGtUofihEp9jvVuRLWFjopaUJs4JANKO5pmRfXgzdayt74xUKz2/q
VQCp2dCmCSXSIyYUwoY/Dg9+3RQ6Ebt3YfSWBGUrxyW+EyYtCGz4lHzV3Wb+QThM
daV+wHXlz0vW4Zr6rUz6D6WlyiK9IlhEX+hdYJagFnHmKXNcpHHl2LvU
=sP7K
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.5-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.5
A collection of fixes since the merge window, mostly driver specific but
there's a few in the core that clean up fallout from the refactorings
done in the last cycle.
According to user manual, it is required that FLL_LAMBDA > 0
in all cases (Integer and Franctional modes).
Fixes: 9a76f1ff6e ("ASoC: Add initial WM8962 CODEC driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1576065442-19763-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Clean up the driver with the new managed buffer allocation API.
The superfluous snd_pcm_lib_malloc_pages() and
snd_pcm_lib_free_pages() calls are dropped.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20191210142614.19405-20-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Clean up the driver with the new managed buffer allocation API.
The superfluous snd_pcm_lib_malloc_pages() and
snd_pcm_lib_free_pages() calls are dropped.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20191210142614.19405-19-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Clean up the driver with the new managed buffer allocation API.
The superfluous snd_pcm_lib_malloc_pages() and
snd_pcm_lib_free_pages() calls are dropped.
Cc: Cheng-Yi Chiang <cychiang@chromium.org>
Cc: Benson Leung <bleung@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20191210142614.19405-18-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
The dai codec needs to ensure that on one dai is used at any time.
This is currently protected by bit atomic operation. With this change,
it done with a mutex instead.
This change is not about functionality or efficiency. It is done with
the hope that it help maintainability in the future.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20191206103542.485224-1-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add "DAC mux" DAPM widget in CS42l51 audio codec routes,
to support DAC mux control and to remove error trace
"DAC Mux has no paths" at widget creation.
Note: ADC path of DAC mux is not routed in this patch.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20191203141627.29471-1-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Chip supports soft stepping of volume changes and it is enabled by
default.
This patch adds a control for it, so it could be either made slower
(two sample periods per step instead of one), or disabled.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20191129132719.11603-1-nikita.yoush@cogentembedded.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the datasheet, there are some registers can only be changed
when SHDN is 0. Changing these settings during SHDN = 1 can compromise
device stability and performance specifications.
Saves SHDN before writing to these sensitive registers and restores SHDN
afterward.
Here is the register list codec driver of max98090 wants to change:
M98090_REG_QUICK_SYSTEM_CLOCK 0x04
M98090_REG_QUICK_SAMPLE_RATE 0x05
M98090_REG_DAI_INTERFACE 0x06
M98090_REG_DAC_PATH 0x07
M98090_REG_MIC_DIRECT_TO_ADC 0x08
M98090_REG_LINE_TO_ADC 0x09
M98090_REG_ANALOG_MIC_LOOP 0x0A
M98090_REG_ANALOG_LINE_LOOP 0x0B
M98090_REG_SYSTEM_CLOCK 0x1B
M98090_REG_CLOCK_MODE 0x1C
M98090_REG_CLOCK_RATIO_NI_MSB 0x1D
M98090_REG_CLOCK_RATIO_NI_LSB 0x1E
M98090_REG_CLOCK_RATIO_MI_MSB 0x1F
M98090_REG_CLOCK_RATIO_MI_LSB 0x20
M98090_REG_MASTER_MODE 0x21
M98090_REG_INTERFACE_FORMAT 0x22
M98090_REG_TDM_CONTROL 0x23
M98090_REG_TDM_FORMAT 0x24
M98090_REG_IO_CONFIGURATION 0x25
M98090_REG_FILTER_CONFIG 0x26
M98090_REG_INPUT_ENABLE 0x3E
M98090_REG_OUTPUT_ENABLE 0x3F
M98090_REG_BIAS_CONTROL 0x42
M98090_REG_DAC_CONTROL 0x43
M98090_REG_ADC_CONTROL 0x44
M98090_REG_DRC_TIMING 0x33
M98090_REG_DRC_COMPRESSOR 0x34
M98090_REG_DRC_EXPANDER 0x35
M98090_REG_DSP_FILTER_ENABLE 0x41
M98090_REG_EQUALIZER_BASE 0x46
M98090_REG_RECORD_BIQUAD_BASE 0xAF
M98090_REG_DIGITAL_MIC_ENABLE 0x13
M98090_REG_DIGITAL_MIC_CONFIG 0x14
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20191128151908.180871-1-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
HP output driver has two parameters that can be configured to reduce
pop noise: power-on delay and ramp-up step time. Two new kcontrols
have been added to set these parameters.
Also have to alter timeout in aic31xx_dapm_power_event() because default
timeout does fire when higher supported power-on delay are configured.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20191128135447.26458-1-nikita.yoush@cogentembedded.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 019033c854 ("ASoC: Intel: hdac_hdmi:
add Icelake support").
Icelake HDMI audio is supported by the HDMI codec driver,
which can be used both in non-DSP (legacy HDA) and with
DSP (SOF) configurations.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191126145304.24204-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
max98090_interrupt() and max98090_pll_work() run in 2 different threads.
There are 2 possible races:
Note: M98090_REG_DEVICE_STATUS = 0x01.
Note: ULK == 0, PLL is locked; ULK == 1, PLL is unlocked.
max98090_interrupt max98090_pll_work
----------------------------------------------
schedule max98090_pll_work
restart max98090 codec
receive ULK INT
assert ULK == 0
schedule max98090_pll_work (1).
In the case (1), the PLL is locked but max98090_interrupt unnecessarily
schedules another max98090_pll_work.
max98090_interrupt max98090_pll_work max98090 codec
----------------------------------------------------------------------
ULK = 1
receive ULK INT
read 0x01
ULK = 0 (clear on read)
schedule max98090_pll_work
restart max98090 codec
ULK = 1
receive ULK INT
read 0x01
ULK = 0 (clear on read)
read 0x01
assert ULK == 0 (2).
In the case (2), both max98090_interrupt and max98090_pll_work read
the same clear-on-read register. max98090_pll_work would falsely
thought PLL is locked.
Note: the case (2) race is introduced by the previous commit ("ASoC:
max98090: exit workaround earlier if PLL is locked") to check the status
and exit the loop earlier in max98090_pll_work.
There are 2 possible solution options:
A. turn off ULK interrupt before scheduling max98090_pll_work; and turn
on again before exiting max98090_pll_work.
B. remove the second thread of execution.
Option A cannot fix the case (2) race because it still has 2 threads
access the same clear-on-read register simultaneously. Although we
could suppose the register is volatile and read the status via I2C could
be much slower than the hardware raises the bits.
Option B introduces a maximum 10~12 msec penalty delay in the interrupt
handler. However, it could only punish the jack detection by extra
10~12 msec.
Adopts option B which is the better solution overall.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20191122073114.219945-4-tzungbi@google.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the datasheet, PLL lock time typically takes 2 msec and
at most takes 7 msec.
Check the lock status every 1 msec and exit the workaround if PLL is
locked.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20191122073114.219945-3-tzungbi@google.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It was observed Baytrail-based chromebooks could cause continuous PLL
unlocked when using playback stream and capture stream simultaneously.
Specifically, starting a capture stream after started a playback stream.
As a result, the audio data could corrupt or turn completely silent.
As the datasheet suggested, the maximum PLL lock time should be 7 msec.
The workaround resets the codec softly by toggling SHDN off and on if
PLL failed to lock for 10 msec. Notably, there is no suggested hold
time for SHDN off.
On Baytrail-based chromebooks, it would easily happen continuous PLL
unlocked if there is a 10 msec delay between SHDN off and on. Removes
the msleep().
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20191122073114.219945-2-tzungbi@google.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The simple-card tries to signal the codec to disable rate constraints,
see commit 2458adb8f9 ("SoC: simple-card-utils: set 0Hz to sysclk when
shutdown"). This wasn't handled by the codec, instead it would set the
FLL frequency to 0Hz which isn't working. Since we don't have any rate
constraints just ignore this request.
Fixes: 13409d27cb ("ASoC: wm8904: configure sysclk/FLL automatically")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191122232532.22258-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
If CONFIG_SPI is n, SND_SOC_RT5677_SPI also is n, building fails:
sound/soc/codecs/rt5677.o: In function `rt5677_irq':
rt5677.c:(.text+0x2dbf): undefined reference to `rt5677_spi_hotword_detected'
sound/soc/codecs/rt5677.o: In function `rt5677_dsp_work':
rt5677.c:(.text+0x3709): undefined reference to `rt5677_spi_write'
This adds stub helpers to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 461c623270 ("ASoC: rt5677: Load firmware via SPI using delayed work")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20191127082145.6100-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some more development work for v5.5. Highlights include:
- More cleanups from Morimoto-san.
- Trigger word detection for RT5677.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl3bzrQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0LkMB/4/MkpN4F2WudNCKgmYay2gw3hq8aOR
5Xh/SE6N3BEgBpQiMEUdePRT6LqnQMsSpOaUoKfd4nFvCyLaV7itaYzQuUpo+UJ/
a4UDHJPVfrDJeFghWqSngfEW/N66mpO3UuAvhSRTR3ku0T31v9FkcLsMbdxVUpLC
ablSaFfPCOtTQOsG9blRUL/GAWUhGzPI/Hl4VldS0FvKDmMDY2fxt7QxXRaEYItc
i1Uthklxd0BfRmDqv0WEpduUhbwzg6Uir9pXSisux7DpMk1Li0IyPST5UcRl0Zf4
CKL/qfdQANpufj9kGmrlCOnXB9P5/XYVwfYV430WqMyw0QaOzzSrxT7C
=CZ/+
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: More updates for v5.5
Some more development work for v5.5. Highlights include:
- More cleanups from Morimoto-san.
- Trigger word detection for RT5677.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The RST (reset-gpios) is low active so the driver must handle it
accordingly.
Add comments to explain clearly how the line is used.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191120131753.6831-3-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Expose mixer control API for reading and writing controls from the kernel.
This API can be used by ALSA kernel drivers with ADSP support to
read and write firmware-defined memory regions.
Signed-off-by: Li Xu <li.xu@cirrus.com>
Signed-off-by: David Rhodes <david.rhodes@cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1573847653-17094-2-git-send-email-david.rhodes@cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The tlv320aic31xx devices allow to adjust the output common-mode voltage
for best analog performance. The datasheet states that the common mode
voltage should be set to be <= AVDD/2.
This changes allows to configure the output common-mode voltage via a DT
property. If the property is absent the voltage is automatically chosen
as the highest voltage below/equal to AVDD/2.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191118151207.28576-1-l.stach@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
In case the RST line is connected to a GPIO line it needs to be pulled high
when the driver probes to be able to use the codec.
Add support also for cases when more than one codec is is controlled by the
same GPIO line by requesting the gpio with GPIOD_FLAGS_BIT_NONEXCLUSIVE.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113124734.27984-3-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver forgets to call pm_runtime_disable in remove and
probe failure.
Add the calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191118073707.28298-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver misses calls to pm_runtime_disable and regulator_bulk_disable
in remove and a call to free_irq in probe failure.
Add the calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191118073633.28237-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to switching the HV to LV mode while stopping playback,
the charge pump capacitor will be discharged to the source of the pump circuit.
Therefore, this patch removed the event control.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20191118091624.18699-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The current code assumes that the power is turned off in
SND_SOC_BIAS_OFF. If there are no actual regulator the codec isn't
turned off and the registers are not reset to their default values but
the regcache is still marked as dirty. Thus a value might not be written
to the hardware if it is set to the default value. Do a software reset
before turning off the power to make sure the registers are always reset
to their default states.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191112223629.21867-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
jack_detect_work will be triggered by rt5682_irq. We should cancel
it if hs_jack is set to null.
Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191111222152.19723-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The headphone jack on buddy was broken with the following commit:
commit 6b5da66322 ("ASoC: rt5645: read jd1_1 status for jd
detection").
This changes the jd_mode for buddy to 4 so buddy can read from the same
register that was used in the working version of this driver without
affecting any other devices that might use this, since no other device uses
jd_mode = 4. To test this I plugged and uplugged the headphone jack, verifying
audio works.
Signed-off-by: Jacob Rasmussen <jacobraz@google.com>
Reviewed-by: Ross Zwisler <zwisler@google.com>
Link: https://lore.kernel.org/r/20191111185957.217244-1-jacobraz@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This adds a new mode WM8904_CLK_AUTO which automatically enables the FLL
if a frequency different than the MCLK is set.
These additions make the codec work with the simple-card driver in
general and especially in systems where the MCLK doesn't match the
required clock.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191108203152.19098-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit adds the Dialog DA7213 audio codec as a selectable option
in the kernel config. Currently the driver can only be selected for
Intel Baytrail/Cherrytrail devices or if SND_SOC_ALL_CODECS is enabled.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20191108174843.11227-3-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to limitations of the clocking configuration, we have no way of
scheduling our hibernation before the bdw dsp hibernates. This causes
issues when the system suspends with an open stream. We need userspace
to toggle the kcontrol before we are suspended so that any writes on
suspend are not lost and we don't corrupt the regmap.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-9-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The irq is disabled at suspend to avoid running the threaded irq
handler after the codec has been powered off. At resume, codec irq is
re-enabled and the interrupt status register is checked to see if
headphone has been pluggnd/unplugged while the device is suspended.
There is still a chance that the headphone gets enabled or disabled
after the codec is suspended. disable_irq syncs the threaded irq
handler, but soc-jack's threaded irq handler schedules a delayed
work to poll gpios (for debounce). This is still OK. The codec won't
be powered back on again because all audio paths have been suspended,
and there are no force enabled supply widgets (MICBIAS1 is disabled).
The gpio status read after codec power off could be wrong, so the
gpio values are checked again after resume.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-8-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
MCLK1 gets disabled at suspend and re-enabled at resume. Before
MCLK1 is re-enabled, if the DSP is already on (either the DSP was
left on during suspend, or the DSP is turned on early at resume),
i2c register read returns garbage and corrupts the regmap cache.
This patch stops the DSP before suspend and restarts it after
resume with a dalay to ensure MCLK is on while loading firmware.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-7-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec dies when RT5677_PWR_ANLG2(MX-64h) is set to 0xACE1
while it's streaming audio over SPI. The DSP firmware turns
on PLL2 (MX-64 bit 8) when SPI streaming starts. However regmap
does not believe that register can change by itself. When
BST1 (bit 15) is turned on with regmap_update_bits(), it doesn't
read the register first before write, so PLL2 power bit is
cleared by accident.
Marking MX-64h as volatile in regmap solved the issue.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-6-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a DAPM audio path from "DMIC L1" to "DSP Buffer" so that
when hotwording is enabled, DAPM does not power off the codec
with SND_SOC_BIAS_OFF.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-5-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Before a hotword is detected, GPIO1 pin is configured as IRQ
output so that jack detect works. When a hotword is detected,
the DSP firmware configures the GPIO1 pin as GPIO1 and
drives a 1. rt5677_irq() is called after a rising edge on
the GPIO1 pin, due to either jack detect event or hotword
event, or both. All possible events are checked and handled
in rt5677_irq() where GPIO1 pin is configured back to IRQ
output if a hotword is detected.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-4-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The firmware rt5677_elf_vad is an ELF binary obtained from
request_firmware(). Sections of the ELF are loaded to
the DSP via SPI. A model (e.g. en_us.mmap) can optionally be
loaded to the DSP at RT5677_MODEL_ADDR to overwrite the
baked-in model in rt5677_elf_vad.
Then we switch to DSP mode, load firmware, and let DSP run.
When a hotword is detected, an interrupt is fired and
rt5677_irq() is called. When 'DSP VAD Switch' is turned off,
the codec is set back to normal mode.
The kcontrol 'DSP VAD Switch' is automatically enabled/disabled
when the hotwording PCM stream is opened/closed.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-2-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The recent change (*) in the ALSA memalloc core allows us to drop the
special vmalloc-specific allocation and page handling. This patch
coverts to the common code.
(*) 1fe7f397cf: ALSA: memalloc: Add vmalloc buffer allocation
support
7e8edae39f: ALSA: pcm: Handle special page mapping in the
default mmap handler
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20191108094641.20086-8-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent change (*) in the ALSA memalloc core allows us to drop the
special vmalloc-specific allocation and page handling. This patch
coverts to the common code.
(*) 1fe7f397cf: ALSA: memalloc: Add vmalloc buffer allocation
support
7e8edae39f: ALSA: pcm: Handle special page mapping in the
default mmap handler
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191108094641.20086-7-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>