Bump version
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Convert two more Intel NIC drivers to dev_consume_skb_any() to help
make dropped packet profiling sane.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove a source of latency spikes (in my case up to 10ms) by not calling
code that uses mdelay() for feeding a phy statistic (rx errors for idle
symbols - not data -> idle_errors) while being called with a spinlock held.
As idle_errors isn't read, this patch only removes unused code and data.
Later, more complicated changes may be applied to address the spinlock and
allow for some PHY diagnostics by harvesting this PHY stats register fully.
This patch is designed to fix the issue and be safe for longterm/stable.
For the Intel e1000e driver, the same change was applied in 2008 with
commit 23033fad5b ("e1000e: remove phy read from inside spinlock").
The mdelay is triggered by HW/SW semaphores, thus it depends on the HW.
I've HW that triggers it even when idle. Others may trigger it only e.g.
when Ethernet ports aquire or loose the link or on ifconfig up / down.
We've noticed this first from delays in frame rx/tx due to the mdelay().
Example command for checking if the issue is triggered: cyclictest -Smp1
(Look for occasional "Max:" values > 4000 or use -b 4000 to stop if greater)
It was observed with I350 ports connected to other I350 ports, but not
if driver and EEPROM was modified to run the I350 in EEPROM-less mode.
phy_stats.idle_errors and .receive_errors (isn't touched) occupy 64 not
used bits in the adapter struct: Their allocation may be removed as well.
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Todd Fujinaka <todd.fujinaka@intel.com>
Fixes: 12dcd86b75 ("igb: fix stats handling") (this added the spin_lock)
Signed-off-by: Bernhard Kaindl <bk-linux@use.startmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is typo in ixgbe.h, two marcro definition of IXGBE_MAX_L2A_QUEUES to 4,
delete one, clear the compiler warning.
Signed-off-by: Ethan Zhao <ethan.zhao@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch consolidates the logic behind dynamically setting TXDCTL.WTHRESH
depending on interrupt throttle rate (ITR) setting regardless of BQL.
Previously TXDCTL.WTHRESH was dynamically being set only with BQL being
enabled, but we have to set it regardless of BQL when ITR is low to avoid
Tx stalls/hangs.
CC: John Greene <jogreene@redhat.com>
Reported by: Masayuki Gouji <gouji.masayuki@jp.fujitsu.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes couple of wait loops on autoneg that are not needed.
During validation we noticed that the loops always time out, so there
should be no user impact.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Convert the normal packet completion path to dev_consume_skb_any() so
packet drop profiling via dropwatch or perf top -G -e skb_kfree_skb
is not cluttered with false hits.
Compile tested only. There is a dev_kfree_skb_any() in the routine
ixgbe_ptp_tx_hwtstamp() in ixgbe_ptp.c that looks like a conversion
candidate but I wasn't familiar enough with the code to pull the
trigger.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The number of Tx queues was not being updated due to some issues when
generating the patches. This change makes sure to add the lines necessary
to update the number of Tx queues correctly.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change reduces the buffer size to 2K for all page sizes. The basic
idea is that since most frames only have a 1500 MTU supporting a buffer
size larger than this is somewhat wasteful. As such I have reduced the
size to 2K for all page sizes which will allow for more uses per page.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_put_tx_csum() needs to return skb pointer back to the caller
because it reallocates a new one in case of lack of skb headroom.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch demonstrates the effect of delaying update of HW tailptr.
(based on earlier patch by Jesper)
burst=1 is the default. It sends one packet with xmit_more=false
burst=2 sends one packet with xmit_more=true and
2nd copy of the same packet with xmit_more=false
burst=3 sends two copies of the same packet with xmit_more=true and
3rd copy with xmit_more=false
Performance with ixgbe (usec 30):
burst=1 tx:9.2 Mpps
burst=2 tx:13.5 Mpps
burst=3 tx:14.5 Mpps full 10G line rate
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for being able to propagate port states to e.g: notifiers
or other kernel parts, do not manipulate the port state directly, but
instead use a helper function which will allow us to do a bit more than
just setting the state.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following crash:
[ 63.976822] general protection fault: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
[ 63.980094] CPU: 1 PID: 15 Comm: ksoftirqd/1 Not tainted 3.17.0-rc6+ #648
[ 63.980094] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 63.980094] task: ffff880117dea690 ti: ffff880117dfc000 task.ti: ffff880117dfc000
[ 63.980094] RIP: 0010:[<ffffffff817e6d07>] [<ffffffff817e6d07>] u32_destroy_key+0x27/0x6d
[ 63.980094] RSP: 0018:ffff880117dffcc0 EFLAGS: 00010202
[ 63.980094] RAX: ffff880117dea690 RBX: ffff8800d02e0820 RCX: 0000000000000000
[ 63.980094] RDX: 0000000000000001 RSI: 0000000000000002 RDI: 6b6b6b6b6b6b6b6b
[ 63.980094] RBP: ffff880117dffcd0 R08: 0000000000000000 R09: 0000000000000000
[ 63.980094] R10: 00006c0900006ba8 R11: 00006ba100006b9d R12: 0000000000000001
[ 63.980094] R13: ffff8800d02e0898 R14: ffffffff817e6d4d R15: ffff880117387a30
[ 63.980094] FS: 0000000000000000(0000) GS:ffff88011a800000(0000) knlGS:0000000000000000
[ 63.980094] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 63.980094] CR2: 00007f07e6732fed CR3: 000000011665b000 CR4: 00000000000006e0
[ 63.980094] Stack:
[ 63.980094] ffff88011a9cd300 ffffffff82051ac0 ffff880117dffce0 ffffffff817e6d68
[ 63.980094] ffff880117dffd70 ffffffff810cb4c7 ffffffff810cb3cd ffff880117dfffd8
[ 63.980094] ffff880117dea690 ffff880117dea690 ffff880117dfffd8 000000000000000a
[ 63.980094] Call Trace:
[ 63.980094] [<ffffffff817e6d68>] u32_delete_key_freepf_rcu+0x1b/0x1d
[ 63.980094] [<ffffffff810cb4c7>] rcu_process_callbacks+0x3bb/0x691
[ 63.980094] [<ffffffff810cb3cd>] ? rcu_process_callbacks+0x2c1/0x691
[ 63.980094] [<ffffffff817e6d4d>] ? u32_destroy_key+0x6d/0x6d
[ 63.980094] [<ffffffff810780a4>] __do_softirq+0x142/0x323
[ 63.980094] [<ffffffff810782a8>] run_ksoftirqd+0x23/0x53
[ 63.980094] [<ffffffff81092126>] smpboot_thread_fn+0x203/0x221
[ 63.980094] [<ffffffff81091f23>] ? smpboot_unpark_thread+0x33/0x33
[ 63.980094] [<ffffffff8108e44d>] kthread+0xc9/0xd1
[ 63.980094] [<ffffffff819e00ea>] ? do_wait_for_common+0xf8/0x125
[ 63.980094] [<ffffffff8108e384>] ? __kthread_parkme+0x61/0x61
[ 63.980094] [<ffffffff819e43ec>] ret_from_fork+0x7c/0xb0
[ 63.980094] [<ffffffff8108e384>] ? __kthread_parkme+0x61/0x61
tp could be freed in call_rcu callback too, the order is not guaranteed.
John Fastabend says:
====================
Its worth noting why this is safe. Any running schedulers will either
read the valid class field or it will be zeroed.
All schedulers today when the class is 0 do a lookup using the
same call used by the tcf_exts_bind(). So even if we have a running
classifier hit the null class pointer it will do a lookup and get
to the same result. This is particularly fragile at the moment because
the only way to verify this is to audit the schedulers call sites.
====================
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert says:
====================
udp: Generalize GSO for UDP tunnels
This patch set generalizes the UDP tunnel segmentation functions so
that they can work with various protocol encapsulations. The primary
change is to set the inner_protocol field in the skbuff when creating
the encapsulated packet, and then in skb_udp_tunnel_segment this data
is used to determine the function for segmenting the encapsulated
packet. The inner_protocol field is overloaded to take either an
Ethertype or IP protocol.
The inner_protocol is set on transmit using skb_set_inner_ipproto or
skb_set_inner_protocol functions. VXLAN and IP tunnels (for fou GSO)
were modified to call these.
Notes:
- GSO for GRE/UDP where GRE checksum is enabled does not work.
Handling this will require some special case code.
- Software GSO now supports many varieties of encapsulation with
SKB_GSO_UDP_TUNNEL{_CSUM}. We still need a mechanism to query
for device support of particular combinations (I intend to
add ndo_gso_check for that).
- MPLS seems to be the only previous user of inner_protocol. I don't
believe these patches can affect that. For supporting GSO with
MPLS over UDP, the inner_protocol should be set using the
helper functions in this patch.
- GSO for L2TP/UDP should also be straightforward now.
v2:
- Respin for Eric's restructuring of skbuff.
Tested GRE, IPIP, and SIT over fou as well as VLXAN. This was
done using 200 TCP_STREAMs in netperf.
GRE
IPv4, FOU, UDP checksum enabled
TCP_STREAM TSO enabled on tun interface
14.04% TX CPU utilization
13.17% RX CPU utilization
9211 Mbps
TCP_STREAM TSO disabled on tun interface
27.82% TX CPU utilization
25.41% RX CPU utilization
9336 Mbps
IPv4, FOU, UDP checksum disabled
TCP_STREAM TSO enabled on tun interface
13.14% TX CPU utilization
23.18% RX CPU utilization
9277 Mbps
TCP_STREAM TSO disabled on tun interface
30.00% TX CPU utilization
31.28% RX CPU utilization
9327 Mbps
IPIP
FOU, UDP checksum enabled
TCP_STREAM TSO enabled on tun interface
15.28% TX CPU utilization
13.92% RX CPU utilization
9342 Mbps
TCP_STREAM TSO disabled on tun interface
27.82% TX CPU utilization
25.41% RX CPU utilization
9336 Mbps
FOU, UDP checksum disabled
TCP_STREAM TSO enabled on tun interface
15.08% TX CPU utilization
24.64% RX CPU utilization
9226 Mbps
TCP_STREAM TSO disabled on tun interface
30.00% TX CPU utilization
31.28% RX CPU utilization
9327 Mbps
SIT
FOU, UDP checksum enabled
TCP_STREAM TSO enabled on tun interface
14.47% TX CPU utilization
14.58% RX CPU utilization
9106 Mbps
TCP_STREAM TSO disabled on tun interface
31.82% TX CPU utilization
30.82% RX CPU utilization
9204 Mbps
FOU, UDP checksum disabled
TCP_STREAM TSO enabled on tun interface
15.70% TX CPU utilization
27.93% RX CPU utilization
9097 Mbps
TCP_STREAM TSO disabled on tun interface
33.48% TX CPU utilization
37.36% RX CPU utilization
9197 Mbps
VXLAN
TCP_STREAM TSO enabled on tun interface
16.42% TX CPU utilization
23.66% RX CPU utilization
9081 Mbps
TCP_STREAM TSO disabled on tun interface
30.32% TX CPU utilization
30.55% RX CPU utilization
9185 Mbps
Baseline (no encp, TSO and LRO enabled)
TCP_STREAM
11.85% TX CPU utilization
15.13% RX CPU utilization
9452 Mbps
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_set_inner_protocol to set inner Ethernet protocol to
ETH_P_TEB before transmit. This is needed for GSO with UDP tunnels.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_set_inner_protocol to set inner Ethernet protocol to
protocol being encapsulation by GRE before tunnel_xmit. This is
needed for GSO if UDP encapsulation (fou) is being done.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_set_inner_ipproto to set inner IP protocol to IPPROTO_IPV4
before tunnel_xmit. This is needed if UDP encapsulation (fou) is
being done.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_set_inner_ipproto to set inner IP protocol to IPPROTO_IPV6
before tunnel_xmit. This is needed if UDP encapsulation (fou) is
being done.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_udp_segment is the function called from udp4_ufo_fragment to
segment a UDP tunnel packet. This function currently assumes
segmentation is transparent Ethernet bridging (i.e. VXLAN
encapsulation). This patch generalizes the function to
operate on either Ethertype or IP protocol.
The inner_protocol field must be set to the protocol of the inner
header. This can now be either an Ethertype or an IP protocol
(in a union). A new flag in the skbuff indicates which type is
effective. skb_set_inner_protocol and skb_set_inner_ipproto
helper functions were added to set the inner_protocol. These
functions are called from the point where the tunnel encapsulation
is occuring.
When skb_udp_tunnel_segment is called, the function to segment the
inner packet is selected based on the inner IP or Ethertype. In the
case of an IP protocol encapsulation, the function is derived from
inet[6]_offloads. In the case of Ethertype, skb->protocol is
set to the inner_protocol and skb_mac_gso_segment is called. (GRE
currently does this, but it might be possible to lookup the protocol
in offload_base and call the appropriate segmenation function
directly).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
bpf: add search pruning optimization and tests
patch #1 commit log explains why eBPF verifier has to examine some
instructions multiple times and describes the search pruning optimization
that improves verification speed for branchy programs and allows more
complex programs to be verified successfully.
This patch completes the core verifier logic.
patch #2 adds more verifier tests related to branches and search pruning
I'm still working on Andy's 'bitmask for stack slots' suggestion. It will be
done on top of this patch.
The current verifier algorithm is brute force depth first search with
state pruning. If anyone can come up with another algorithm that demonstrates
better results, we'll replace the algorithm without affecting user space.
Note verifier doesn't guarantee that all possible valid programs are accepted.
Overly complex programs may still be rejected.
Verifier improvements/optimizations will guarantee that if a program
was passing verification in the past, it will still be passing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
add 4 extra tests to cover jump verification better
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
consider C program represented in eBPF:
int filter(int arg)
{
int a, b, c, *ptr;
if (arg == 1)
ptr = &a;
else if (arg == 2)
ptr = &b;
else
ptr = &c;
*ptr = 0;
return 0;
}
eBPF verifier has to follow all possible paths through the program
to recognize that '*ptr = 0' instruction would be safe to execute
in all situations.
It's doing it by picking a path towards the end and observes changes
to registers and stack at every insn until it reaches bpf_exit.
Then it comes back to one of the previous branches and goes towards
the end again with potentially different values in registers.
When program has a lot of branches, the number of possible combinations
of branches is huge, so verifer has a hard limit of walking no more
than 32k instructions. This limit can be reached and complex (but valid)
programs could be rejected. Therefore it's important to recognize equivalent
verifier states to prune this depth first search.
Basic idea can be illustrated by the program (where .. are some eBPF insns):
1: ..
2: if (rX == rY) goto 4
3: ..
4: ..
5: ..
6: bpf_exit
In the first pass towards bpf_exit the verifier will walk insns: 1, 2, 3, 4, 5, 6
Since insn#2 is a branch the verifier will remember its state in verifier stack
to come back to it later.
Since insn#4 is marked as 'branch target', the verifier will remember its state
in explored_states[4] linked list.
Once it reaches insn#6 successfully it will pop the state recorded at insn#2 and
will continue.
Without search pruning optimization verifier would have to walk 4, 5, 6 again,
effectively simulating execution of insns 1, 2, 4, 5, 6
With search pruning it will check whether state at #4 after jumping from #2
is equivalent to one recorded in explored_states[4] during first pass.
If there is an equivalent state, verifier can prune the search at #4 and declare
this path to be safe as well.
In other words two states at #4 are equivalent if execution of 1, 2, 3, 4 insns
and 1, 2, 4 insns produces equivalent registers and stack.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Copy short frames and keep the buffers mapped, re-allocate skb instead of
memory copy for long frames.
- Add support for setting/getting rx_copybreak using generic ethtool tunable
Changes V3:
* As Eric Dumazet's suggestion that removing the copybreak module parameter
and only keep the ethtool API support for rx_copybreak.
Changes V2:
* Implements rx_copybreak
* Rx_copybreak provides module parameter to change this value
* Add tunable_ops support for rx_copybreak
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fast clone cloning can actually avoid an atomic_inc(), if we
guarantee prior clone_ref value is 1.
This requires a change kfree_skbmem(), to perform the
atomic_dec_and_test() on clone_ref before setting fclone to
SKB_FCLONE_UNAVAILABLE.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ccid_activate is only called by __init ccid_initialize_builtins in same module.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
dccp_mib_init is only called by __init dccp_init in same module.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lets use a proper structure to clearly document and implement
skb fast clones.
Then, we might experiment more easily alternative layouts.
This patch adds a new skb_fclone_busy() helper, used by tcp and xfrm,
to stop leaking of implementation details.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we have two different policies for orphan sockets
that repeatedly stall on zero window ACKs. If a socket gets
a zero window ACK when it is transmitting data, the RTO is
used to probe the window. The socket is aborted after roughly
tcp_orphan_retries() retries (as in tcp_write_timeout()).
But if the socket was idle when it received the zero window ACK,
and later wants to send more data, we use the probe timer to
probe the window. If the receiver always returns zero window ACKs,
icsk_probes keeps getting reset in tcp_ack() and the orphan socket
can stall forever until the system reaches the orphan limit (as
commented in tcp_probe_timer()). This opens up a simple attack
to create lots of hanging orphan sockets to burn the memory
and the CPU, as demonstrated in the recent netdev post "TCP
connection will hang in FIN_WAIT1 after closing if zero window is
advertised." http://www.spinics.net/lists/netdev/msg296539.html
This patch follows the design in RTO-based probe: we abort an orphan
socket stalling on zero window when the probe timer reaches both
the maximum backoff and the maximum RTO. For example, an 100ms RTT
connection will timeout after roughly 153 seconds (0.3 + 0.6 +
.... + 76.8) if the receiver keeps the window shut. If the orphan
socket passes this check, but the system already has too many orphans
(as in tcp_out_of_resources()), we still abort it but we'll also
send an RST packet as the connection may still be active.
In addition, we change TCP_USER_TIMEOUT to cover (life or dead)
sockets stalled on zero-window probes. This changes the semantics
of TCP_USER_TIMEOUT slightly because it previously only applies
when the socket has pending transmission.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reported-by: Andrey Dmitrov <andrey.dmitrov@oktetlabs.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
cipso_v4_cache_init is only called by __init cipso_v4_init
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip4_frags_ctl_register is only called by __init ipfrag_init
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two functions are used to inform dash firmware that driver is been
brought up or brought down. So call these two functions only when hardware dash
function is enabled.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function "rtl8168_oob_notify", using function "rtl_eri_write" to access
eri register 0xe8, instead of using MAC register "ERIDR" and "ERIAR" to
access it.
For using function "rtl_eri_write" in function "rtl8168_oob_notify", need to
move down "rtl8168_oob_notify" related functions under the function
"rtl_eri_write".
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DASH function not only RTL8168DP can support, but also RTL8168EP.
So change the name of function "r8168dp_check_dash" to "r8168_check_dash".
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the name of function "rtl_w1w0_eri" to "rtl_w0w1_eri".
In this function, the local variable "val" is "write zeros then write ones".
Please see below code.
(val & ~m) | p
In this patch, change the function name from "xx_w1w0_xx" to "xx_w0w1_xx".
The changed function name is more suitable for it's behavior.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change function name from "rtl_w1w0_phy" to "rtl_w0w1_phy".
And its behavior from "write ones then write zeros" to
"write zeros then write ones".
In Realtek internal driver, bitwise operations are almost "write zeros then
write ones". For easy to port hardware parameters from Realtek internal driver
to Linux kernal driver "r8169", we would like to change this function's
behavior and its name.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RTL8168F RTL8168FB RTL8168G RTL8168GU RTL8411 RTL8411B RTL8402 RTL8107E,
the magic packet enable bit is changed to eri 0xde bit0.
In this patch, change magic packet enable bit of these chips to eri 0xde bit0.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8168FB RTL8168G RTL8168GU RTL8411 RTL8411B RTL8106EUS RTL8402 can
support get mac address from backup mac address register.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the error cases for vnet_start_xmit()'s "out_dropped" label
is port == NULL, so only mess with port->clean_timer when port is not NULL.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_switch_suspend() and dsa_switch_resume() functions are only used
when PM_SLEEP is enabled, so they need #ifdef CONFIG_PM_SLEEP protection
to avoid a compiler warning.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling ether_setup is redundant since alloc_etherdev calls it.
Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Proper CHECKSUM_COMPLETE support needs to adjust skb->csum
when we remove one header. Its done using skb_gro_postpull_rcsum()
In the case of IPv4, we know that the adjustment is not really needed,
because the checksum over IPv4 header is 0. Lets add a comment to
ease code comprehension and avoid copy/paste errors.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3243acd37f
("ieee802154: add __init to lowpan_frags_sysctl_register")
added __init to lowpan_frags_ns_sysctl_register instead of
lowpan_frags_sysctl_register
Suggested-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
