The Kontron N6311 and N6411 SoMs are very similar to N6310. In
preparation to add support for them, we move the common nodes to a
separate file imx6ul-kontron-n6x1x-som-common.dtsi.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a devicetree for the Kobo Clara HD Ebook reader. It
is on based on boards called "e60k02". It is equipped with an
imx6sll SoC.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Netronix board E60K02 can be found some several Ebook-Readers,
at least the Kobo Clara HD and the Tolino Shine 3. The board
is equipped with different SoCs requiring different pinmuxes.
For now the following peripherals are included:
- LED
- Power Key
- Cover (gpio via hall sensor)
- RC5T619 PMIC (the kernel misses support for rtc and charger
subdevices).
- Backlight via lm3630a
- Wifi sdio chip detection (mmc-powerseq and stuff)
It is based on vendor kernel but heavily reworked due to many
changed bindings.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the parallel panel that is supported is the CLAA WVGA panel,
which is the one that comes with the i.MX51 Babbage board.
The default parallel panel that goes with the imx53-qsb board is
the Seiko 43WVF1G LCD, so switch to the Seiko one.
While at it convert to DRM bindings.
The parallel display still remains disabled as the default display
port is the TVE output.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6UL 14x14 EVK board, mag3110's power is controlled by
sensor regulator, assign power supplies for mag3110 driver
to do power management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name is supposed to be generic, use "magnetometer" instead
of "mag3110" for magnetometer node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6UL 14x14 EVK board, sensors' power are controlled
by GPIO5_IO02, add GPIO regulator for sensors to manage
their power.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX GPT driver ONLY supports 1 instance, i.MX6UL already has
GPT1 enabled by default, so GPT2 should be disabled.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cooling device properties "#cooling-cells" should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in the
CPU node it is trying to bring up, so that it can register a cooling
device.
Add such missing properties.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cooling device properties "#cooling-cells" should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in the
CPU node it is trying to bring up, so that it can register a cooling
device.
Add such missing properties.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cooling device properties "#cooling-cells" should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in the
CPU node it is trying to bring up, so that it can register a cooling
device.
Add such missing properties.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This regulator supplies other devices and not only usb host1 so
rename it.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These changes make the WiFi on the APF6 board work again.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RTS/CTS lines are wired to the Bluetooth chip so add uart-has-rtscts
property to uart2.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the mdio bus and the phy to the fec-node.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the function node around the pinctrl nodes that was obsoleted
by commit 5fcdf6a7ed ("pinctrl: imx: Allow parsing DT without
function nodes").
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to Documentation/devicetree/bindings/iio/accel/mma8452.txt,
the correct interrupt-names are "INT1" and "INT2", so fix them
accordingly.
While at it, modify the node to only specify "INT2" since providing
two interrupts is not necessary or useful (the driver will only use
one).
Signed-off-by: Fabio Estevam <festevam@gmail.com>
[andrew.smirnov@gmail.com modified the patch to drop INT1]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch enables the recovery mode now available.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds missing i2c recovery modes and corrects wrongly named
ones.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6dl-yapp4 Draco and Ursa boards use the I2C3 bus to control some
external devices through the /dev files.
So enable the I2C3 bus on all board variants, not just on Hydra.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The second UART is needed for 3D or MFD printer control.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pca9535 gpio expander is present on the Rex baseboard, but missing
from the dtsi.
The pca9535 is on i2c2 bus which is common to the three SOM
variants (Basic/Pro/Ultra), thus it is activated by default.
Add also the new gpio controller and the associated interrupt line
MX6QDL_PAD_NANDF_CS3__GPIO6_IO16.
Signed-off-by: Gilles DOFFE <gilles.doffe@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Without configuring this pinctrl, the ID value can't be got correctly,
then, the dual-role switch can't work well.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This change disables the DMA support (RX/TX) on the NXP's fsl_lpuart
driver - the PIO mode is used instead. This change is necessary for better
robustness of BK4's device use cases with many potentially interrupted
short serial transfers.
Without it the driver hangs when some distortion happens on UART lines.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to Documentation/devicetree/bindings/sound/simple-card.txt
the 'simple-audio-card,dai-link' may be omitted when the card has
only one DAI link, which is the case here.
Get rid of 'simple-audio-card,dai-link' in order to fix the following
build warning with W=1:
arch/arm/boot/dts/imx6q-gw54xx.dts:19.32-31.5: Warning (unit_address_vs_reg): /sound-digital/simple-audio-card,dai-link@0: node has a unit name, but no reg property
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the touch keyboard present on Hydra board. The controller
is connected only using I2C lines. The interrupt line is not
available hence we use the polling mode.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The device node name should reflect generic class of a device so rename
the "iram" node to "sram". This will be also in sync with upcoming DT
schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"internal_j8" and "internal_j9" are network interfaces that are not
exposed outside the board and were only ever used for debugging purposes.
Get rid of them as they are not needed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move the CAN enablement from SoM DTSi to board DTS, as each board might need
different CAN configuration. Moreover, disable CAN2 on the PDK2 as it is not
available on any connector. This also fixes on-SoM SD slot operation, as it
shares pins with the CAN2.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "opp-suspend" property for i.MX7D to make sure system
suspend with max available opp.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 800MHz opp speed grading fuse mask should be 0xd instead
of 0xf according to fuse map definition:
SPEED_GRADING[1:0] MHz
00 800
01 500
10 1000
11 1200
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to Documentation/devicetree/bindings/sound/simple-card.txt
the 'simple-audio-card,dai-link' may be omitted when the card has
only one DAI link, which is the case here.
Get rid of 'simple-audio-card,dai-link' in order to fix the following
build warning with W=1:
arch/arm/boot/dts/imx6qdl-gw551x.dtsi:109.32-121.5: Warning (unit_address_vs_reg): /sound-digital/simple-audio-card,dai-link@0: node has a unit name, but no reg property
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass the memory unit name in order to fix the following build warning
with W=1:
arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi:23.9-26.4: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
Cc: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Replace "simple-bus" with "simple-mfd" for anatop node in order
to fix the following build warnings with W=1:
arch/arm/boot/dts/imx6sx.dtsi:603.31-616.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-1p1: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:618.31-631.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-3p0: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:633.31-646.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-2p5: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:648.32-663.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddcore: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:665.33-679.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddpcie: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:681.31-696.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddsoc: missing or empty reg/ranges property
Based on a patch from Marco Felsch for the imx6qdl.dtsi.
Cc: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the possibility to wake the module with an external signal
as defined in the Colibri standard
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the pinmuxing and a inactive node for flexcan1 on SODIMM 55/63
and move the inactive flexcan nodes to imx6ull-colibri-eval-v3.dtsi
where they belong.
Note that this commit does not enable flexcan functionality, but rather
eases the effort needed to do so.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the watchdog to the imx6ull-colibri devicetree
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reduce the current drawn from VCC_BATT when the main power on the 3V3
pins to the module are switched off.
This switches off SoC internal pull resistors which are provided on the
module for TAMPER7 and TAMPER9 SoC pin and switches on a pull down
instead of a pullup for the USBC_DET module pin (TAMPER2).
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
