A lot of drivers check the frame protocol for ETH_P_PAE,
for various reasons (like making those more reliable).
Add a new flags bitmap to the TX control info and a new
flag indicating the control port protocol is in use to
let all drivers also apply such logic to other control
port protocols, should they be configured.
Also use the new flag in the iwlwifi drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The rate scale windows are cleared twice as part of the init.
Cleanup this duplication in both mvm and dvm.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If channel switch is pending and we remove interface we can
crash like showed below due to passing NULL vif to mac80211:
BUG: unable to handle kernel paging request at fffffffffffff8cc
IP: [<ffffffff8130924d>] strnlen+0xd/0x40
Call Trace:
[<ffffffff8130ad2e>] string.isra.3+0x3e/0xd0
[<ffffffff8130bf99>] vsnprintf+0x219/0x640
[<ffffffff8130c481>] vscnprintf+0x11/0x30
[<ffffffff81061585>] vprintk_emit+0x115/0x4f0
[<ffffffff81657bd5>] printk+0x61/0x63
[<ffffffffa048987f>] ieee80211_chswitch_done+0xaf/0xd0 [mac80211]
[<ffffffffa04e7b34>] iwl_chswitch_done+0x34/0x40 [iwldvm]
[<ffffffffa04f83c3>] iwlagn_commit_rxon+0x2a3/0xdc0 [iwldvm]
[<ffffffffa04ebc50>] ? iwlagn_set_rxon_chain+0x180/0x2c0 [iwldvm]
[<ffffffffa04e5e76>] iwl_set_mode+0x36/0x40 [iwldvm]
[<ffffffffa04e5f0d>] iwlagn_mac_remove_interface+0x8d/0x1b0 [iwldvm]
[<ffffffffa0459b3d>] ieee80211_do_stop+0x29d/0x7f0 [mac80211]
This is because we nulify ctx->vif in iwlagn_mac_remove_interface()
before calling some other functions that teardown interface. To fix
just check ctx->vif on iwl_chswitch_done(). We should not call
ieee80211_chswitch_done() as channel switch works were already canceled
by mac80211 in ieee80211_do_stop() -> ieee80211_mgd_stop().
Resolve:
https://bugzilla.redhat.com/show_bug.cgi?id=979581
Cc: stable@vger.kernel.org
Reported-by: Lukasz Jagiello <jagiello.lukasz@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We're not planning to support P2P on older devices, so
remove the Kconfig option and associated code for it.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The BT_CONFIG command that is sent to the device during
startup will enable BT coex unless the module parameter
turns it off, but on devices without Bluetooth this may
cause problems, as reported in Redhat BZ 885407.
Fix this by sending the BT_CONFIG command only when the
device has Bluetooth.
Cc: stable@vger.kernel.org
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
There's no need to have 'forward' debugfs function declarations
as part of the macros because the macros are always used after
the static functions are defined already, so remove them.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
5 and 10 MHz support needs to know the current operating channel width,
add the chandef to the rate control API.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
The old nl80211 testmode is no longer useful in iwlwifi,
we're moving towards a new model internally and there's
no open tool to use it, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If someone wants to disable AMPDU, there is the 11n_disable
module parameter.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Nobody will ever wants to run without this. Make it true always.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This parameter is really not useful, remove it.
Leave the variable in priv in case someone wants
to play with it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of using #ifdef CONFIG_IWLWIFI_DEBUG, remove the
iwlwifi_mod_params.debug_level variable completely and
make iwl_have_debug_level() always return false in the
non-debug case. This way, the optimiser will elide all
code for it automatically without having to add #ifdefs.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since driver does not use control.rates[0].count, we have never set that
variable. But currently, after rate control API rewrite, this is required
by mac80211. Otherwise legacy rates control does not work and we transmit
always at 1Mbit/s on pre 11n networks.
[same fix as for iwlegacy, thanks Stanislaw!]
Signed-off-by: Moshe Benji <Moshe.Benji@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
First step of chain noise calibration process had disable flag
check inverted. Chain noise calibration never started because
of this.
Tested on intel 5300 with two antennas attached. The driver
correctly disabled one chain.
Cc: stable@vger.kernel.org
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge to get the wil6210 changes that a cfg80211 change needs.
A conflict in drivers/net/wireless/ath/ath9k/init.c was just
whitespace changes.
Also fix a semantic conflict due to cw1200 using WoWLAN which
I had modified in my tree.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to take up the space for devices that don't
support WoWLAN, and most drivers can even make the support
data static const (except where it's modified at runtime.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For testing the D3 (WoWLAN) firmware, it is useful to be able
to run the firmware with instrumentation while the host isn't
sleeping and can poke at the firmware debug logging etc.
Implement this by a debugfs file. When the file is opened the
D3 firmware is loaded and all regular commands are blocked.
While the file is being read, poll the firmware's PME status
flag and report EOF once it changes to non-zero. When it is
closed, do (most of) the resume processing. This lets a user
just "cat" the file. Pressing Ctrl-C to kill the cat process
will resume the firwmare as though the platform resumed for
non-wireless reason and when the firmware wants to wake up
reading from the file automatically completes.
Unlike in real suspend, only disable interrupts and don't
reset the TX/RX hardware while in the test mode. This is a
workaround for some interrupt problems that happen only when
the PCIe link isn't fully reset (presumably by changing the
PCI config space registers which the core PCI code does.)
Note that while regular operations are blocked from sending
commands to the firmware, they could still be made and cause
strange mac80211 issues. Therefore, while using this testing
feature you need to be careful to not try to disconnect, roam
or similar, and will see warnings for such attempts.
Als note that this requires an upcoming firmware change to
tell the driver the location of the PME status flag in SRAM.
D3 test will fail if the firmware doesn't report the pointer.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The pointer that gets used is already const, so the
structs can obviously be const as well.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a number of parameters that aren't really hardware
specific but rather define how the DVM firmware is used.
Move these into the DVM configuration.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The next patches will move some more configuration
data that isn't needed by mvm into this struct, so
rename it now since it won't just be ops.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The MVM firmware doesn't communicate this way, it instead
assumes D3 configuration is complete after a specific host
command (which must be last) has been sent. Handling this
bit thus belongs into the firmware API code, i.e. DVM.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In 63b77bf489
iwlwifi: dvm: don't send zeroed LQ cmd
I tried to avoid to send zeroed LQ cmd, but I made a (very)
stupid mistake in the memcmp.
Since this patch has been ported to stable, the fix should
go to stable too.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=58341
Cc: stable@vger.kernel.org
Reported-by: Hinnerk van Bruinehsen <h.v.bruinehsen@fu-berlin.de>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 and the Intel drivers all define crypto
constants, move them to ieee80211.h instead.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the stations are being restored because of unassoc
RXON, the LQ cmd may not have been initialized because it
is initialized only after association.
Sending zeroed LQ_CMD makes the fw unhappy: it raises
SYSASSERT_2078.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
[move zero_lq and make static const]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We can check buf against NULL instead of having additional bool
variable.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If on iwl_dump_nic_event_log() error occurs before that function
initialize buf, we process uninitiated pointer in
iwl_dbgfs_log_event_read() and can hit "BUG at mm/slub.c:3409"
Resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=951241
Cc: stable@vger.kernel.org
Reported-by: ian.odette@eprize.com
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for the secondary channel offset IE in channel
switch announcements. This is necessary for proper handling
of CSA on HT access points.
For this to work it is also necessary to convert everything
here to use chandef structs instead of just channels. The
driver updates aren't really correct though. In particular,
the TI wl18xx driver update can't possibly be right since
it just ignores the new channel width for lack of firmware
API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Until now we didn't handle properly the FLUSH ampdu action
coming from mac80211. This could result in SCD queue leak:
mac80211 would STOP_FLUSH an AMPDU Tx session and remove
the station. If we had still packets on the ring, we
wouldn't deallocate the SCD queue and wait for it to be
empty.
The indication of the queue being empty comes from the Tx
response flow which relies on the tid_data structure. The
problem is that this structure has been cleared when the
station has been removed.
In order to solve this issue, block in the STOP_FLUSH
ampdu_action until the SCD queue is flushed, and only then,
let mac80211 move forward to remove the station.
iwlagn_txfifo_flush had to be enhanced to allow this.
The bug fixed here caused the "txq_id mismatch: 12 0" print.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using IWL_MVM_STATION_COUNT and IWL_INVALID_STATION together
isn't a good idea as they have different values. Always use
IWL_MVM_STATION_COUNT for an invalid station in MVM and move
the definition of the IWL_INVALID_STATION constant into the
DVM driver to avoid making such mistakes again. The one use
in the transport code can be hard-coded to -1 instead as the
station ID is passed as an integer there.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Many platforms have issues processing a wakeup signal
while they're still suspending, and will ignore it.
Since our device thinks it woke the platform, and the
platform ignored the signal, it will sleep without
WoWLAN being enabled as the device disables WoWLAN
when having woken the platform.
Resolve this by making the device wait for 10 seconds
after getting the suspend signal before waking up the
platform.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Alex Romosan reported that since the mac80211 changes in
"mac80211: start auth/assoc timeout on frame status" and
the subsequent fixes in "mac80211: fix auth/assoc timeout
handling" (commits 1672c0e319 and 89afe614c0) there's
sometimes an issue connecting to a 5 GHz network with the
iwlwifi DVM driver.
The reason appears to be that since these commits any bad
TX status makes mac80211 immediately try again, causing
all of the authentication attempts to be quickly rejected
by the firmware as it hasn't heard a beacon yet. Before,
it would wait for the timeout regardless of status.
To fix this, invoke the passive-no-RX workaround when not
associated yet as well. This will cause the first frame
to get lost, but then the driver will stop the queues and
the second attempt will only be transmitted after hearing
a beacon, thus delaying it appropriately to not make the
firmware reject it again.
Reported-by: Alex Romosan <romosan@sycorax.lbl.gov>
Tested-by: Alex Romosan <romosan@sycorax.lbl.gov>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
