This patch performs code cleanup by defining macros for the ptp-timestamp
filters.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/xen-netfront.c: In function ‘netback_changed’:
drivers/net/xen-netfront.c:2038:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (dev->state == XenbusStateClosed)
^
drivers/net/xen-netfront.c:2041:2: note: here
case XenbusStateClosing:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently genphy_read_abilities() has been added that dynamically detects
clause 22 PHY abilities. I *think* this detection should work with all
supported PHY's, at least for the ones with basic features sets, i.e.
PHY_BASIC_FEATURES and PHY_GBIT_FEATURES. So let's remove setting these
features explicitly and rely on phylib feature detection.
I don't have access to most of these PHY's, therefore I'd appreciate
regression testing.
v2:
- make the feature constant a comment so that readers know which
features are supported by the respective PHY
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A merge flow is formed from 2 sub flows. The match fields of the merge are
the same as the first sub flow that has formed it, with the actions being
a combination of the first and second sub flow. Therefore, a merge flow
should replace sub flow 1 when offloaded.
Offload valid merge flows by using a new 'flow mod' message type to
replace an existing offloaded rule. Track the deletion of sub flows that
are linked to a merge flow and revert offloaded merge rules if required.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the merging of 2 sub flows, a new 'merge' flow will be created and
written to FW. The TC layer is unaware that the merge flow exists and will
request stats from the sub flows. Conversely, the FW treats a merge rule
the same as any other rule and sends stats updates to the NFP driver.
Add links between merge flows and their sub flows. Use these links to pass
merge flow stats updates from FW to the underlying sub flows, ensuring TC
stats requests are handled correctly. The updating of sub flow stats is
done on (the less time critcal) TC stats requests rather than on FW stats
update.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When combining 2 sub_flows to a single 'merge flow' (assuming the merge is
valid), the merge flow should contain the same match fields as sub_flow 1
with actions derived from a combination of sub_flows 1 and 2. This action
list should have all actions from sub_flow 1 with the exception of the
output action that triggered the 'implicit recirculation' by sending to
an internal port, followed by all actions of sub_flow 2. Any pre-actions
in either sub_flow should feature at the start of the action list.
Add code to generate a new merge flow and populate the match and actions
fields based on the sub_flows. The offloading of the flow is left to
future patches.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two flows can be merged if the second flow (after recirculation) matches
on bits that are either matched on or explicitly set by the first flow.
This means that if a packet hits flow 1 and recirculates then it is
guaranteed to hit flow 2.
Add a 'can_merge' function that determines if 2 sub_flows in a merge hint
can be validly merged to a single flow.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a merge hint is received containing 2 flows that are matched via an
implicit recirculation (sending to and matching on an internal port), fw
reports that the flows (called sub_flows) may be able to be combined to a
single flow.
Add infastructure to accept and process merge hint messages. The actual
merging of the flows is left as a stub call.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each flow is given a context ID that the fw uses (along with its cookie)
to identity the flow. The flows stats are updated by the fw via this ID
which is a reference to a pre-allocated array entry.
In preparation for flow merge code, enable the nfp_fl_payload structure to
be accessed via this stats context ID. Rather than increasing the memory
requirements of the pre-allocated array, add a new rhashtable to associate
each active stats context ID with its rule payload.
While adding new code to the compile metadata functions, slightly
restructure the existing function to allow for cleaner, easier to read
error handling.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The neighbour table in the FW only accepts next hop entries if the egress
port is an nfp repr. Modify this to allow the next hop to be an internal
port. This means that if a packet is to egress to that port, it will
recirculate back into the system with the internal port becoming its
ingress port.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW may receive a packet with its ingress port marked as an internal port.
If a rule does not exist to match on this port, the packet will be sent to
the NFP driver. Modify the flower app to detect packets from such internal
ports and convert the ingress port to the correct kernel space netdev.
At this point, it is assumed that fallback packets from internal ports are
to be sent out said port. Therefore, set the redir_egress bool to true on
detection of these ports.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, it is assumed that fallback packets will be from reprs. Modify
this to allow an app to receive non-repr ports from the fallback channel -
e.g. from an internal port. If such a packet is received, do not update
repr stats.
Change the naming function calls so as not to imply it will always be a
repr netdev returned. Add the option to set a bool value to redirect a
fallback packet out the returned port rather than RXing it. Setting of
this bool in subsequent patches allows the handling of packets falling
back when they are due to egress an internal port.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent FW modifications allow the offloading of non repr ports. These
ports exist internally on the NFP. So if a rule outputs to an 'internal'
port, then the packet will recirculate back into the system but will now
have this internal port as it's incoming port. These ports are indicated
by a specific type field combined with an 8 bit port id.
Add private app data to assign additional port ids for use in offloads.
Provide functions to lookup or create new ids when a rule attempts to
match on an internal netdev - the only internal netdevs currently
supported are of type openvswitch. Have a netdev notifier to release
port ids on netdev unregister.
OvS offloads rules that match on internal ports as TC egress filters.
Ensure that such rules are accepted by the driver.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Write to a FW symbol to indicate that the driver supports flow merging. If
this symbol does not exist then flow merging and recirculation is not
supported on the FW. If support is available, add a stub to deal with FW
to kernel merge hint messages.
Full flow merging requires the firmware to support of flow mods. If it
does not, then do not attempt to 'turn on' flow merging.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting vport->bw_limit to hdev->tm_info.pg_info[0].bw_limit
in hclge_tm_vport_tc_info_update, vport->bw_limit can be as big as
HCLGE_ETHER_MAX_RATE (100000), which can not fit into u16 (65535).
So this patch fixes it by using u32 for vport->bw_limit.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The input parameter "proto" in function hclge_set_vlan_filter_hw()
is asked to be __be16, but got u16 when calling it in function
hclge_update_port_base_vlan_cfg().
This patch fixes it by converting it with htons().
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 21e043cd81 ("net: hns3: fix set port based VLAN for PF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to routes and FDB entries, the neighbour table is
reflected to the device.
Set an offload indication on the neighbour in case it was programmed to
the device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Next patch will add offload indication to neighbours, but the indication
should only be altered in case the neighbour was successfully added to /
deleted from the device.
Propagate neighbour update errors, so that they could be taken into
account by the next patch.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This check isn't really needed and we can simplify the code and save
some CPU cycles by removing it. Only in case of an error none of these
bits are set, and calling the NAPI callback doesn't hurt in this case.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a function pointer array makes this easier to read and better
maintainable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a function pointer array makes this easier to read and better
maintainable. AFAIK function pointer arrays cause some performance
drawback due to Spectre mitigation, but we're not in a hot path here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes some redundant BH disable when initializing
and uninitializing command queue.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is pending skb in RX flow when close the port, and the
pending buffer is not cleaned, the new packet will be added to
the pending skb when the port opens again, and the first new
packet has error data.
This patch cleans the pending skb when clean RX ring.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some cases, PHY may not be connected to MDIO bus, then
the driver will initialize fail since MDIO bus initialization
fails.
This patch fixes it by skipping the MDIO bus initialization
when PHY is inexistent.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to hardware description, reset level that should be
triggered are not consistent in a module. For example, in SSU
common errors, the first two bits has no need to do reset,
but the other bits need global reset.
This patch sets separate reset level for all RAS and MSI-X
interrupts by adding a reset_lvel field in struct hclge_hw_error,
and fixes some incorrect reset level.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently hardware may have not enough buffer to receive packet
when it has used more than two MPS(maximum packet size) of
buffer, but there are still a lot of shared buffer left unused
when TC num is small.
This patch divides shared buffer to be used between TC when
the port supports DCB, and adjusts the waterline and threshold
according to user manual for the port that does not support
DCB.
This patch also change hclge_get_tc_num's return type to u32
to avoid signed-unsigned mix with divide.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently RX shared buffer' threshold size for speific TC is
set to smaller value when the TC's PFC is not enabled, which may
cause performance problem because hardware may not have enough
hardware buffer when PFC is not enabled.
This patch sets the same threshold size for all TC no matter if
the specific TC's PFC is enabled.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a GRO packet is received by driver, the cwr field in the
struct tcphdr needs to be checked to decide whether to set the
SKB_GSO_TCP_ECN for skb_shinfo(skb)->gso_type.
So this patch adds hns3_gro_complete to do that, and adds the
hns3_handle_bdinfo to handle the hns3_gro_complete and
hns3_rx_checksum.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the parameters of hns3_rx_checksum to be more specific to
what is used internally, rather than passing in a pointer to the
whole hns3_desc. Reduces duplicate code and bring this function
inline with the approach used in hns3_set_gro_param.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, ndo_set_vf_vlan() in hns3 driver was implemented
wrong. It adds or removes VLAN into VLAN filter for VF, but VF is
unaware of it.
This patch fixes it. When VF loads up, it firstly queries the port
based VLAN state from PF. When user change port based VLAN state
from PF, PF firstly checks whether the VF is alive. If the VF is
alive, then PF notifies the VF the modification; otherwise PF
configure the port based VLAN state directly.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, ndo_set_vf_vlan() in hns3 driver was implemented
wrong. It adds or removes VLAN into VLAN filter for VF, but VF is
unaware of it.
Indeed, ndo_set_vf_vlan() is expected to enable or disable port based
VLAN (hardware inserts a specified VLAN tag to all TX packets for a
specified VF) . When enable port based VLAN, we use port based VLAN id
as VLAN filter entry. When disable port based VLAN, we use VLAN id of
VLAN device.
This patch fixes it for PF, enable/disable port based VLAN when calls
ndo_set_vf_vlan().
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, in TX direction, driver implements the TX VLAN offload
by checking the VLAN header in skb, and filling it into TX descriptor.
Usually it works well, but if enable inserting VLAN header based on
port, it may conflict when out_tag field of TX descriptor is already
used, and cause RAS error.
In RX direction, hardware supports stripping max two VLAN headers.
For vlan_tci in skb can only store one VLAN tag, when RX VLAN offload
enabled, driver tells hardware to strip one VLAN header from RX
packet; when RX VLAN offload disabled, driver tells hardware not to
strip VLAN header from RX packet. Now if port based insert VLAN
enabled, all RX packets will have the port based VLAN header. This
header is useless for stack, driver needs to ask hardware to strip
it. Unfortunately, hardware can't drop this VLAN header, and always
fill it into RX descriptor, so driver has to identify and drop it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our hardware supports inserting a specified VLAN header for each
function when sending packets. User can enable it with command
"ip link set <devname> vf <vfid> vlan <vlan id>".
For this VLAN header is inserted by hardware, not from stack,
hardware also needs to strip it from received packets before
sending to stack. In this case, driver needs to tell
hardware which VLAN to insert or strip.
The current VLAN initialization doesn't allow inserting
VLAN header by hardware, this patch modifies it, in order be
compatible with VLAN inserted base on port.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If new PHY modes are added people may miss to update all relevant places
in the kernel. Therefore add a build bug check for new modes in enum
ethtool_link_mode_bit_indices that haven't been added to phylib yet.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently new modes have been added to ethtool.h, but the related
extension to phylib hasn't been done yet. So add support for these
modes.
v2:
- add missing 100Gbps and 50Gbps modes
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The definition of array settings[] is quite lengthy meanwhile. Add a
macro to shrink the definition.
v2:
- Fix an indentation issue
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF's control message handler seems like a good base to built
on for request-reply control messages. Split it out to allow
for reuse.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During probe we clear vNIC configuration in case the device
wasn't closed cleanly by previous driver. Move that code
before netdev init, so netdev init can already try to apply
its config parameters.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Soon we will try to write to the vNIC mailbox without RTNL held.
Add a new mutex to protect access to specific parts of the PCI
control BAR.
Move the mailbox size checking to the mailbox lock() helper, where
it can be more effective (happen prior to potential overwrite of
other data).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the reconfig was a quick update, we could have results available from
firmware within 200us.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to improve readability and prepare for future code changes,
move sdev specific init/uninit code into separate functions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
offload dev is stored in sdev struct. However, first netdevsim instance
is used as a priv. Change this to be sdev to as it is shared among
multiple netdevsim instances.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some netdevsim bpf debugfs files are per-sdev, yet they are defined per
netdevsim instance. Move them under sdev directory.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make code easier to read, move shared dev bits into a separate file.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For reporting the common set of SW timestamping capabilities, use
ethtool_op_get_ts_info() instead of re-implementing it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For reporting the common set of SW timestamping capabilities, use
ethtool_op_get_ts_info() instead of re-implementing it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For reporting the common set of SW timestamping capabilities, use
ethtool_op_get_ts_info() instead of re-implementing it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During coredump analysis, it is not easy to obtain the address of
backend_info in xen-netback.
So far there are two ways to obtain backend_info:
1. Do what xenbus_device_find() does for vmcore to find the xenbus_device
and then derive it from dev_get_drvdata().
2. Extract backend_info from callstack of xenwatch (e.g., netback_remove()
or frontend_changed()).
This patch adds a reference from xenvif to backend_info so that it would be
much more easier to obtain backend_info during coredump analysis.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_c45_aneg_done() is used by phylib as fallback for c45 PHY's if
callback aneg_done isn't defined. So we don't have to set this
explicitly. Same for genphy_c45_pma_read_abilities().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit f6b19b354d ("net: devlink: select NET_DEVLINK
from drivers") adds implicit select of NET_DEVLINK for
netdevsim, the code does not have to deal with the case
when CONFIG_NET_DEVLINK is not enabled. So remove the ifcase.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
