Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New GPIO IRQs are allocated and mapped dynamically by default when
GPIO IRQ infrastructure is used by cherryview-pinctrl driver.
This causes issues on some Intel platforms [1][2] with broken BIOS which
hardcodes Linux IRQ numbers in their ACPI tables.
On such platforms cherryview-pinctrl driver should allocate and map all
GPIO IRQs at probe time.
Side effect - "Cannot allocate irq_descs @ IRQ%d, assuming pre-allocated\n"
can be seen at boot log.
NOTE. It still may fail if boot sequence will changed and some interrupt
controller will be probed before cherryview-pinctrl which will shift Linux IRQ
numbering (expected with CONFIG_SPARCE_IRQ enabled).
[1] https://bugzilla.kernel.org/show_bug.cgi?id=194945
[2] https://lkml.org/lkml/2017/9/28/153
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Chris Gorman <chrisjohgorman@gmail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Chris Gorman <chrisjohgorman@gmail.com>
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Chris Gorman <chrisjohgorman@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the same way as it's done in pinctrl-cherryview.c we would provide
a readback TX buffer state.
Fixes: 17fab47369 ("pinctrl: intel: Set pin direction properly")
Reported-by: "Bourque, Francis" <francis.bourque@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: "Bourque, Francis" <francis.bourque@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Decrease indentation in intel_gpio_set() to make it looking slightly better
and be in align with intel_gpio_get().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Intel Lewisburg has the same GPIO hardware than Intel Sunrisepoint-H
except few differences in register offsets and pin lists. Because of
this we add a separate pinctrl driver for Lewisburg.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is desktop version Intel Cannon Lake PCH. The GPIO hardware is the
same but pin list differs a bit. Add support for this to the existing
Cannon Lake pin controller driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The fix prevents unintended wakes from second level GPIO pin interrupts.
On some Intel Kabylake platforms, it is observed that GPIO pin interrupts
can wake the platform from suspend-to-idle, even though the IRQ is not
configured as IRQF_NO_SUSPEND or enable_irq_wake().
This can cause undesired wakes on Mobile devices such as Laptops and
Chromebook devices. For example a headset jack insertion is not a desired
wake source on Chromebook devices.
The pinctrl-intel (GPIO controller) driver implements a "Shared IRQ" model.
All GPIO pin interrupts are OR'ed and mapped to a first level IRQ14 (or
IRQ15). The driver registers an irq_chip struct and maps an irq_domain for
the GPIO pin interrupts. The IRQ14 handler demuxes and calls the second
level IRQ for the respective pin.
In the suspend entry flow, at suspend_noirq stage, the kernel disables IRQs
that are not marked for wake. The pinctrl-intel driver does not implement a
irq_disable() callback (to take advantage of lazy disabling). The
pinctrl-intel GPIO interrupts are not disabled in hardware during suspend
entry, and thus are able to wake the SoC out of suspend-to-idle.
This patch sets the IRQCHIP_MASK_ON_SUSPEND flag for the GPIO irq_chip, to
disable the second level interrupts at suspend_noirq stage via the irq_mask
callbacks. The irq_mask callback disables the IRQs in hardware by
programming the corresponding GPIO pad registers. Only IRQs that are not
marked for wake are disabled.
Signed-off-by: Rushikesh S Kadam <rushikesh.s.kadam@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-and-tested-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver adds pinctrl/GPIO support for Intel Denverton SoC. The GPIO
controller is based on the same hardware design that is already used in
Intel Sunrisepoint so we leverage the core driver here.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Intel pin control drivers are architecture specific so add an if arch
to check for X86 or compile test to ensure continued test coverage.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
WARN_ON causes a backtrace to get logged which is only useful for
kernel bugs. For signalling a firmware bug dev_warn(dev, FW_BUG "...")
should be used.
This fixes users running userspace software to monitor kernel oopses
getting a false positive bug-report every boot because of the wrong
use of WARN_ON.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add one more model to the Chromebook DMI quirk to make it working again.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194945
Fixes: 2a8209fa68 ("pinctrl: cherryview: Extend the Chromebook DMI quirk to Intel_Strago systems")
Reported-by: mail@abhishek.geek.nz
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pinctrl/GPIO support for Intel Cannon Lake PCH. The Cannon
Lake PCH GPIO is based on newer version of the Intel GPIO hardware.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some SoCs not all pins in a group use the same mode when a certain
function is muxed out of them. This makes it possible to specify mode per
pin as an array instead in addition to single integer.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Intel GPIO hardware has a concept of pad groups, which means 1 to 32
pads occupying their own GPI_IS, GPI_IE, PAD_OWN and so on registers. The
existing hardware has the same amount of pads in each pad group (except the
last one) so it is possible to use community->gpp_size to calculate start
offset of each register.
With the next generation SoCs the pad group size is not always the same
anymore which means we cannot use community->gpp_size for register offset
calculations directly.
To support variable size pad groups we introduce struct intel_padgroup that
can be filled in by the client drivers according the hardware pad group
layout. The core driver will always use these when it performs calculations
for pad register offsets. The core driver will automatically populate pad
groups based on community->gpp_size if the driver does not provide any.
This makes sure the existing drivers still work as expected.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Tan Jui Nee <jui.nee.tan@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It turns out there are quite many Chromebooks out there that have the
same keyboard issue than Acer Chromebook. All of them are based on
Intel_Strago reference and report their DMI_PRODUCT_FAMILY as
"Intel_Strago" (Samsung Chromebook 3 and Cyan Chromebooks are exceptions
for which we add separate entries).
Instead of adding each machine to the quirk table, we use
DMI_PRODUCT_FAMILY of "Intel_Strago" that hopefully covers most of the
machines out there currently.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194945
Suggested: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make sure dmi_system_id tables are NULL terminated.
Fixes: 7036502783 ("pinctrl: cherryview: Add a quirk to make Acer
Chromebook keyboard work again")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Add bi-directional and output-enable pin configurations to
the generic bindings and generic pin controlling core.
New drivers or subdrivers:
- Armada 37xx SoC pin controller and GPIO support.
- Axis ARTPEC-6 SoC pin controller support.
- AllWinner A64 R_PIO controller support, and opening up the
AllWinner sunxi driver for ARM64 use.
- Rockchip RK3328 support.
- Renesas R-Car H3 ES2.0 support.
- STM32F469 support in the STM32 driver.
- Aspeed G4 and G5 pin controller support.
Improvements:
- A whole slew of realtime improvements to drivers implementing
irqchips: BCM, AMD, SiRF, sunxi, rockchip.
- Switch meson driver to get the GPIO ranges from the device
tree.
- Input schmitt trigger support on the Rockchip driver.
- Enable the sunxi (AllWinner) driver to also be used on ARM64
silicon.
- Name the Qualcomm QDF2xxx GPIO lines.
- Support GMMR GPIO regions on the Intel Cherryview. This
fixes a serialization problem on these platforms.
- Pad retention support for the Samsung Exynos 5433.
- Handle suspend-to-ram in the AT91-pio4 driver.
- Pin configuration support in the Aspeed driver.
Cleanups:
- The final name of Rockchip RK1108 was RV1108 so rename the
driver and variables to stay consistent.
-----BEGIN PGP SIGNATURE-----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=BCaA
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.12 cycle.
The extra week before the merge window actually resulted in some of
the type of fixes that usually arrive after the merge window already
starting to trickle in from eager developers using -next, I'm
impressed.
I have recruited a Samsung subsubsystem maintainer (Krzysztof) to deal
with the onset of Samsung patches. It works great.
Apart from that it is a boring round, just incremental updates and
fixes all over the place, no serious core changes or anything exciting
like that. The most pleasing to see is Julia Cartwrights work to audit
the irqchip-providing drivers for realtime locking compliance. It's
one of those "I should really get around to looking into that" things
that have been on my TODO list since forever.
Summary:
Core changes:
- add bi-directional and output-enable pin configurations to the
generic bindings and generic pin controlling core.
New drivers or subdrivers:
- Armada 37xx SoC pin controller and GPIO support.
- Axis ARTPEC-6 SoC pin controller support.
- AllWinner A64 R_PIO controller support, and opening up the
AllWinner sunxi driver for ARM64 use.
- Rockchip RK3328 support.
- Renesas R-Car H3 ES2.0 support.
- STM32F469 support in the STM32 driver.
- Aspeed G4 and G5 pin controller support.
Improvements:
- a whole slew of realtime improvements to drivers implementing
irqchips: BCM, AMD, SiRF, sunxi, rockchip.
- switch meson driver to get the GPIO ranges from the device tree.
- input schmitt trigger support on the Rockchip driver.
- enable the sunxi (AllWinner) driver to also be used on ARM64
silicon.
- name the Qualcomm QDF2xxx GPIO lines.
- support GMMR GPIO regions on the Intel Cherryview. This fixes a
serialization problem on these platforms.
- pad retention support for the Samsung Exynos 5433.
- handle suspend-to-ram in the AT91-pio4 driver.
- pin configuration support in the Aspeed driver.
Cleanups:
- the final name of Rockchip RK1108 was RV1108 so rename the driver
and variables to stay consistent"
* tag 'pinctrl-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (80 commits)
pinctrl: mediatek: Add missing pinctrl bindings for mt7623
pinctrl: artpec6: Fix return value check in artpec6_pmx_probe()
pinctrl: artpec6: Remove .owner field for driver
pinctrl: tegra: xusb: Silence sparse warnings
ARM: at91/at91-pinctrl documentation: fix spelling mistake: "contoller" -> "controller"
pinctrl: make artpec6 explicitly non-modular
pinctrl: aspeed: g5: Add pinconf support
pinctrl: aspeed: g4: Add pinconf support
pinctrl: aspeed: Add core pinconf support
pinctrl: aspeed: Document pinconf in devicetree bindings
pinctrl: Add st,stm32f469-pinctrl compatible to stm32-pinctrl
pinctrl: stm32: Add STM32F469 MCU support
Documentation: dt: Remove ngpios from stm32-pinctrl binding
pinctrl: stm32: replace device_initcall() with arch_initcall()
pinctrl: stm32: add possibility to use gpio-ranges to declare bank range
pinctrl: armada-37xx: Add gpio support
pinctrl: armada-37xx: Add pin controller support for Armada 37xx
pinctrl: dt-bindings: Add documentation for Armada 37xx pin controllers
pinctrl: core: Make pinctrl_init_controller() static
pinctrl: generic: Add bi-directional and output-enable
...
After commit 47c950d102 ("pinctrl: cherryview: Do not add all
southwest and north GPIOs to IRQ domain") the driver does not add all
GPIOs to the irqdomain. The reason for that is that those GPIOs cannot
generate IRQs at all, only GPEs (General Purpose Events). This causes
Linux virtual IRQ numbering to change.
However, it seems some CYAN Chromebooks, including Acer Chromebook
hardcodes these Linux IRQ numbers in the ACPI tables of the machine.
Since the numbering is different now, the IRQ meant for keyboard does
not match the Linux virtual IRQ number anymore making the keyboard
non-functional.
Work this around by adding special quirk just for these machines where
we add back all GPIOs to the irqdomain. Rest of the Cherryview/Braswell
based machines will not be affected by the change.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194945
Fixes: 47c950d102 ("pinctrl: cherryview: Do not add all southwest and north GPIOs to IRQ domain")
Reported-by: Adam S Levy <theadamlevy@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some Cherry Trail devices the ASL uses the GMMR GPIO to access
GPIOs so as to serialize MMIO accesses to GPIO registers with the
OS, because:
"Due to a silicon issue, a shared lock must be used to prevent concurrent
accesses across the 4 GPIO controllers.
See Intel Atom Z8000 Processor Series Specification Update (Rev. 005),
errata #CHT34, for further information."
This commit adds support for this opregion, this fixes a number of
ASL errors on my Ezpad mini3 tablet and makes the otg port device/host
muxing which is controlled in firmware on this model work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Switch the generic pin config argument from 16 to 24 bits,
only use 8 bits for the configuration type. We might need to
encode more information about a certain setting than we need
to encode different generic settings.
- Add a cross-talk API to the pin control GPIO back-end,
utilizing pinctrl_gpio_set_config() from GPIO drivers that
want to set up a certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the
GPIO chips, so that they pass a generic configuration for
things like debouncing and single ended (typically open
drain). This change has also been merged in an immutable
branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing
a pin controller before trying to get any hogs.
- For pin controllers putting all group and function definitions
into the device tree, we now have generic code to deal with
this and it is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down.
New subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in
the LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on
GPIOs. Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode.
STM32H743 MCU support.
- Allwinner sunxi: deep simplifications on how to support
subvariants of SoCs without adding to much SoC-specific data
for each subvariant, especially for sun5i variants. New driver
for V3s SoCs. New driver for the H5 SoC. Support A31/A31s
variants with the new variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction.
New subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the
SoC driver to access regmaps. Add infrastructure for pin-bank
retention control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly
in the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm
driver realtime-safe.
-----BEGIN PGP SIGNATURE-----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=IMY0
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Pin control bulk changes for the v4.11 kernel cycle.
Core changes:
- Switch the generic pin config argument from 16 to 24 bits, only use
8 bits for the configuration type. We might need to encode more
information about a certain setting than we need to encode
different generic settings.
- Add a cross-talk API to the pin control GPIO back-end, utilizing
pinctrl_gpio_set_config() from GPIO drivers that want to set up a
certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the GPIO chips,
so that they pass a generic configuration for things like
debouncing and single ended (typically open drain). This change has
also been merged in an immutable branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing a pin
controller before trying to get any hogs.
- For pin controllers putting all group and function definitions into
the device tree, we now have generic code to deal with this and it
is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down. New
subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in the
LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on GPIOs.
Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode. STM32H743 MCU
support.
- Allwinner sunxi: deep simplifications on how to support subvariants
of SoCs without adding to much SoC-specific data for each
subvariant, especially for sun5i variants. New driver for V3s SoCs.
New driver for the H5 SoC. Support A31/A31s variants with the new
variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction. New
subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the SoC
driver to access regmaps. Add infrastructure for pin-bank retention
control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly in
the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm driver
realtime-safe"
* tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (111 commits)
pinctrl: samsung: Fix return value check in samsung_pinctrl_get_soc_data()
pinctrl: intel: unlock on error in intel_config_set_pull()
pinctrl: berlin: make bool drivers explicitly non-modular
pinctrl: spear: make bool drivers explicitly non-modular
pinctrl: mvebu: make bool drivers explicitly non-modular
pinctrl: sunxi: make sun5i explicitly non-modular
pinctrl: sunxi: Remove stray printk call in sun5i driver's probe function
pinctrl: samsung: mark PM functions as __maybe_unused
pinctrl: sunxi: Remove redundant A31s pinctrl driver
pinctrl: sunxi: Support A31/A31s with pinctrl variants
pinctrl: Amend bindings for STM32 pinctrl
pinctrl: Add STM32 pinctrl driver DT bindings
pinctrl: stm32: Add STM32H743 MCU support
include: dt-bindings: Add STM32H7 pinctrl DT defines
gpio: aspeed: Remove dependence on GPIOF_* macros
pinctrl: stm32: fix bad location of gpiochip_lock_as_irq
drivers: pinctrl: add driver for Allwinner H5 SoC
pinctrl: intel: Add Intel Gemini Lake pin controller support
pinctrl: intel: Add support for 1k additional pull-down
pinctrl: intel: Add support for hardware debouncer
...
We need to unlock before returning -EINVAL on this error path.
Fixes: 04cc058f0c ("pinctrl: intel: Add support for 1k additional pull-down")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to VLI64 Intel Atom E3800 Specification Update (#329901)
concurrent read accesses may result in returning 0xffffffff and write
accesses may be dropped silently.
To workaround all accesses must be protected by locks.
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Debounce value is set globally per community. Otherwise user will easily
get a kernel crash when they start using the feature:
BUG: unable to handle kernel paging request at ffffc900003be000
IP: byt_gpio_dbg_show+0xa9/0x430
Make it clear in byt_gpio_reg().
Note that this fix just prevents kernel to crash, but doesn't make any
difference to the existing logic. It means the last caller will win the
trade and debounce value will be configured accordingly. The actual
logic fix needs to be thought about and it's not as important as crash
fix. That's why the latter goes separately and right now.
Fixes: 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
Cc: Cristina Ciocan <cristina.ciocan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit 04ff5a095d ("pinctrl: baytrail: Rectify debounce support")
almost fixes the logic of debuonce but missed couple of things, i.e.
typo in mask when disabling debounce and lack of enabling it back.
This patch addresses above issues.
Reported-by: Jean Delvare <jdelvare@suse.de>
Fixes: 04ff5a095d ("pinctrl: baytrail: Rectify debounce support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver adds pinctrl/GPIO support for Intel Gemini Lake SoC. The
GPIO controller is based on the next generation GPIO hardware but still
compatible with the one supported by the Intel core pinctrl/GPIO driver.
This commit includes material from David E. Box.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The next generation Intel GPIO hardware supports additional 1k pull-down
per-pad. Add support for this to the Intel core pinctrl driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The next generation Intel GPIO hardware has two additional registers
PADCFG2 and PADCFG3. The latter is marked as reserved but the former
includes configuration for per-pad hardware debouncer.
This patch adds support for that in the Intel pinctrl core driver. Since
these are additional features on top of the current generation hardware,
we use revision number and feature flags to enable this if detected.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no need to take pointer of a pointer to an array of SoC data in
platform driver.
Do it in the same way as it's done for ACPI.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Not every pin can be configured. Add missed check to prevent access
violation.
Fixes: 4e80c8f505 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Apparently each GPIO pad's register are 16 bytes, so multiply the pad_map
by that. The same is done in byt_gpio_reg the only other place where
pad_map is used.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While we have no users yet rename the platform driver to use the same
pattern as the rest of Intel SoCs, i.e. use full SoC name in
'apollolake-pinctrl'.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current pinconf packed format allows only 16-bit argument limiting
the maximum value 65535. For most types this is enough. However,
debounce time can be in range of hundreths of milliseconds in case of
mechanical switches so we cannot represent the worst case using the
current format.
In order to support larger values change the packed format so that the
lower 8 bits are used as type which leaves 24 bits for the argument.
This allows representing values up to 16777215 and debounce times up to
16 seconds.
We also convert the existing users to use 32-bit integer when extracting
argument from the packed configuration value.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When DIRECT_IRQ_EN is set, the pin is routed directly to the IO-APIC bypassing
the GPIO driver completely. However, the mask register is still used to
determine if the pin is supposed to generate IRQ or not.
So with commit 3ae02c14d9 the IRQ core masks all IRQs (because of
handle_bad_irq()) the pin connected to the touchscreen gets masked as well and
hence no interrupts.
To make this all work as expected we do not add those GPIOs to the IRQ domain
that can actually propagate interrupts.
Fixes: 3ae02c14d9 ("pinctrl: intel: set default handler to be handle_bad_irq()")
Reported-by: Robert R. Howell <rhowell@uwyo.edu>
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This simplifies error handling and allows us to drop error path handlers
completely.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
implements debounce for Baytrail pin control, but seems wasn't tested properly.
The register which keeps debounce value is separated from the configuration
one. Writing wrong values to the latter will guarantee wrong behaviour of the
driver and even might break something physically.
Besides above there is missed case how to disable it, which is actually done
through the bit in configuration register.
Rectify implementation here by using proper register for debounce value.
Fixes: 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
Cc: Cristina Ciocan <cristina.ciocan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This simplifies error handling and allows us to drop intel_pinctrl_remove()
completely.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are two bits in the PADCFG0 register to configure direction, one per
TX/RX buffers.
For now we wrongly assume that the GPIO is always requested before it is being
used, which is not true when the GPIO is used through irqchip. In this case the
GPIO is never requested and we never enable RX buffer for it.
Fix this by setting both bits accordingly.
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PADCFGLOCK (and PADCFGLOCK_TX) offset in Broxton actually starts at 0x060
and not 0x090 as used in the driver. Fix it to use the correct offset.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No core changes this time. Mainly gradual improvement and
feature growth in the drivers.
New drivers:
- New driver for TI DA850/OMAP-L138/AM18XX pinconf
- The SX150x was moved over from the GPIO subsystem and
reimagined as a pin control driver with GPIO support
in a joint effort by three independent users of this
hardware. The result was amazingly good!
- New subdriver for the Oxnas OX820
Improvements:
- The sunxi driver now supports the generic pin control
bindings rather than the sunxi-specific. Add debouncing
support to the driver.
- Simplifications in pinctrl-single adding a generic parser.
- Two downstream fixes and move the Raspberry Pi BCM2835 over
to use the generic GPIOLIB_IRQCHIP.
-----BEGIN PGP SIGNATURE-----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=Pkzu
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl updates from Linus Walleij:
"Bulk pin control changes for the v4.10 kernel cycle:
No core changes this time. Mainly gradual improvement and
feature growth in the drivers.
New drivers:
- New driver for TI DA850/OMAP-L138/AM18XX pinconf
- The SX150x was moved over from the GPIO subsystem and reimagined as
a pin control driver with GPIO support in a joint effort by three
independent users of this hardware. The result was amazingly good!
- New subdriver for the Oxnas OX820
Improvements:
- The sunxi driver now supports the generic pin control bindings
rather than the sunxi-specific. Add debouncing support to the
driver.
- Simplifications in pinctrl-single adding a generic parser.
- Two downstream fixes and move the Raspberry Pi BCM2835 over to use
the generic GPIOLIB_IRQCHIP"
* tag 'pinctrl-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (92 commits)
pinctrl: sx150x: use new nested IRQ infrastructure
pinctrl: sx150x: handle missing 'advanced' reg in sx1504 and sx1505
pinctrl: sx150x: rename 'reg_advance' to 'reg_advanced'
pinctrl: sx150x: access the correct bits in the 4-bit regs of sx150[147]
pinctrl: mt8173: set GPIO16 to usb iddig mode
pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP
pinctrl: New driver for TI DA850/OMAP-L138/AM18XX pinconf
devicetree: bindings: pinctrl: Add binding for ti,da850-pupd
Documentation: pinctrl: palmas: Add ti,palmas-powerhold-override property definition
pinctrl: intel: set default handler to be handle_bad_irq()
pinctrl: sx150x: add support for sx1501, sx1504, sx1505 and sx1507
pinctrl: sx150x: sort chips by part number
pinctrl: sx150x: use correct registers for reg_sense (sx1502 and sx1508)
pinctrl: imx: fix imx_pinctrl_desc initialization
pinctrl: sx150x: support setting multiple pins at once
pinctrl: sx150x: various spelling fixes and some white-space cleanup
pinctrl: mediatek: use builtin_platform_driver
pinctrl: stm32: use builtin_platform_driver
pinctrl: sunxi: Testing the wrong variable
pinctrl: nomadik: split up and comments MC0 pins
...
We switch the default handler to be handle_bad_irq() instead of
handle_simple_irq() (which was not correct anyway).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the system is suspended to S3 the BIOS might re-initialize certain
GPIO pins back to their original state or it may re-program interrupt mask
of others. For example Acer TravelMate B116-M had BIOS bug where certain
GPIO pin (MF_ISH_GPIO_5) was programmed to trigger on high level, and the
pin state was high once the BIOS gave control to the OS on resume.
This triggers lots of messages like:
irq 117, desc: ffff88017a61e600, depth: 1, count: 0, unhandled: 0
->handle_irq(): ffffffff8109b613, handle_bad_irq+0x0/0x1e0
->irq_data.chip(): ffffffffa0020180, chv_pinctrl_exit+0x2d84/0x12 [pinctrl_cherryview]
->action(): (null)
IRQ_NOPROBE set
We reset the mask back to known state in chv_pinctrl_resume() but that is
called only after device interrupts have already been enabled.
Now, this particular issue was fixed by upgrading the BIOS to the latest
(v1.23) but not everybody upgrades their BIOSes so we fix it up in the
driver as well.
Prevent the possible interrupt storm by moving suspend and resume hooks to
be called at _noirq time instead. Since device interrupts are still
disabled we can restore the mask back to known state before interrupt storm
happens.
Cc: stable@vger.kernel.org
Reported-by: Christian Steiner <christian.steiner@outlook.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If async suspend is enabled, the driver may access registers concurrently
with another instance which may fail because of the bug in Cherryview GPIO
hardware. Prevent this by taking the shared lock while accessing the
hardware in suspend and resume hooks.
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Printing the prefix does not provide any additional information. In
addition this makes the output look more consistent with pinctrl-intel.c.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pin config get() and set() handlers for pin groups were previously not
implemented by this driver. The pin_config_group_set() is particularly useful
for applying a common config setting to all pins in a specified group with a
single call, without the caller needing to reference each individual pin by
name.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Dell XPS 13 (and maybe some others) uses a GPIO (CPU_GP_1) during suspend
to explicitly disable USB touchscreen interrupt. This is done to prevent
situation where the lid is closed the touchscreen is left functional.
The pinctrl driver (wrongly) assumes it owns all pins which are owned by
host and not locked down. It is perfectly fine for BIOS to use those pins
as it is also considered as host in this context.
What happens is that when the lid of Dell XPS 13 is closed, the BIOS
configures CPU_GP_1 low disabling the touchscreen interrupt. During resume
we restore all host owned pins to the known state which includes CPU_GP_1
and this overwrites what the BIOS has programmed there causing the
touchscreen to fail as no interrupts are reaching the CPU anymore.
Fix this by restoring only those pins we know are explicitly requested by
the kernel one way or other.
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=176361
Reported-by: AceLan Kao <acelan.kao@canonical.com>
Tested-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Initialize the spinlock before using it.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.8.0-dwc-bisect #4
Hardware name: Intel Corp. VALLEYVIEW C0 PLATFORM/BYT-T FFD8, BIOS BLAKFF81.X64.0088.R10.1403240443 FFD8_X64_R_2014_13_1_00 03/24/2014
0000000000000000 ffff8800788ff770 ffffffff8133d597 0000000000000000
0000000000000000 ffff8800788ff7e0 ffffffff810cfb9e 0000000000000002
ffff8800788ff7d0 ffffffff8205b600 0000000000000002 ffff8800788ff7f0
Call Trace:
[<ffffffff8133d597>] dump_stack+0x67/0x90
[<ffffffff810cfb9e>] register_lock_class+0x52e/0x540
[<ffffffff810d2081>] __lock_acquire+0x81/0x16b0
[<ffffffff810cede1>] ? save_trace+0x41/0xd0
[<ffffffff810d33b2>] ? __lock_acquire+0x13b2/0x16b0
[<ffffffff810cf05a>] ? __lock_is_held+0x4a/0x70
[<ffffffff810d3b1a>] lock_acquire+0xba/0x220
[<ffffffff8136f1fe>] ? byt_gpio_get_direction+0x3e/0x80
[<ffffffff81631567>] _raw_spin_lock_irqsave+0x47/0x60
[<ffffffff8136f1fe>] ? byt_gpio_get_direction+0x3e/0x80
[<ffffffff8136f1fe>] byt_gpio_get_direction+0x3e/0x80
[<ffffffff813740a9>] gpiochip_add_data+0x319/0x7d0
[<ffffffff81631723>] ? _raw_spin_unlock_irqrestore+0x43/0x70
[<ffffffff8136fe3b>] byt_pinctrl_probe+0x2fb/0x620
[<ffffffff8142fb0c>] platform_drv_probe+0x3c/0xa0
...
Based on the diff it looks like the problem was introduced in
commit 71e6ca61e8 ("pinctrl: baytrail: Register pin control handling")
but I wasn't able to verify that empirically as the parent commit
just oopsed when I tried to boot it.
Cc: Cristina Ciocan <cristina.ciocan@intel.com>
Cc: stable@vger.kernel.org
Fixes: 71e6ca61e8 ("pinctrl: baytrail: Register pin control handling")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
