Right now, some modules such as bonding use proc_create
to create proc entries under /proc/net/, and other modules
such as ipv4 use proc_net_fops_create.
It looks a little chaos.this patch changes all of
proc_net_fops_create to proc_create. we can remove
proc_net_fops_create after this patch.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Larry noticed (and bisected) that commit df881293c6
"cfg80211: Pass TDLS peer's QoS/HT/VHT information during set_station"
broke secure connections. This is is the case only for drivers that
don't support TDLS, where any kind of change, even just the change of
authorized flag that is required for normal operation, was rejected
now. To fix this, remove the checks. I have some patches that will add
proper verification for all the different cases later.
Cc: Jouni Malinen <j@w1.fi>
Bisected-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The information of the peer's capabilities is required for the driver
to perform TDLS Peer UAPSD operations. This information of the peer is
passed by the supplicant using NL80211_CMD_SET_STATION command. This
commit enhances the function nl80211_set_station to pass this
information of the peer to the driver in case this command is used
with the TDLS peer STA.
In addition, make the HT/VHT capability configuration handled more
consistently for other STA cases (reject both instead of just HT).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The information of the peer's capabilities and extended capabilities are
required for the driver to perform TDLS Peer UAPSD operations and off
channel operations. This information of the peer is passed from user space
using NL80211_CMD_SET_STATION command. This commit enhances
the function nl80211_set_station to pass the capability information of
the peer to the driver.
Similarly, there may be need for capability information for other modes,
so allow this to be provided with both add_station and change_station.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In many cases, userspace may need to know which of the
802.11 extended capabilities ("Extended Capabilities
element") are implemented in the driver or device, to
include them e.g. in beacons, assoc request/response
or other frames. Add a new nl80211 attribute to hold
the extended capabilities bitmap for this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When drivers or regulatory have limitations on
40, 80 or 160 MHz channels, advertise these to
userspace via nl80211. Also add a new feature
flag to let userspace know this is supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers might support 80 or 160 MHz only on some
channels for whatever reason, so allow them to disable
these channel widths. Also maintain the new flags when
regulatory bandwidth limitations would disable these
wide channels.
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add new NL80211_CMD_RADAR_DETECT, which starts the Channel
Availability Check (CAC). This command will also notify the
usermode about events (CAC finished, CAC aborted, radar
detected, NOP finished).
Once radar detection has started it should continuously
monitor for radars as long as the channel is active.
This patch enables DFS for AP mode in nl80211/cfg80211.
Based on original patch by Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
[remove WIPHY_FLAG_HAS_RADAR_DETECT again -- my mistake]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Intel Wireless devices are able to make a TCP connection
after suspending, sending some data and waking up when
the connection receives wakeup data (or breaks). Add the
WoWLAN configuration and feature advertising API for it.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_find_vendor_ie() was checking only that the vendor IE would
fit in the remaining IEs buffer. If a corrupt includes a vendor IE
that is too small, we could potentially overrun the IEs buffer.
Fix this by checking that the vendor IE fits in the reported IE length
field and skip it otherwise.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Luciano Coelho <coelho@ti.com>
[change BUILD_BUG_ON to != 1 (from >= 2)]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If user knows the location of a wowlan pattern to be matched in
Rx packet, he can provide an offset with the pattern. This will
help drivers to ignore initial bytes and match the pattern
efficiently.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
[refactor pattern sending]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While technically the TSF isn't an IE, it can be
necessary to distinguish between the TSF from a
beacon and a probe response, in particular in
order to know the next DTIM TBTT, as not all APs
are spec compliant wrt. TSF==0 being a DTIM TBTT
and thus the DTIM count needs to be taken into
account as well.
To allow this, move the TSF into the IE struct
so it can be known whence it came.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no way scan BSS IEs can be NULL as even
if the allocation fails the frame is discarded.
Remove some code checking for this and document
that it is always non-NULL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, cfg80211 will copy beacon IEs from a previously
received hidden SSID beacon to a probe response entry, if
that entry is created after the beacon entry. However, if
it is the other way around, or if the beacon is updated,
such changes aren't propagated.
Fix this by tracking the relation between the probe
response and beacon BSS structs in this case.
In case drivers have private data stored in a BSS struct
and need access to such data from a beacon entry, cfg80211
now provides the hidden_beacon_bss pointer from the probe
response entry to the beacon entry.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This prepares for using the spinlock instead of krefs
which is needed in the next patch to track the refs
of combined BSSes correctly.
Acked-by: Bing Zhao <bzhao@marvell.com> [mwifiex]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a driver requests a specific regulatory domain after cfg80211 already
has one, a struct ieee80211_regdomain is leaked.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/ethernet/intel/e1000e/ethtool.c
drivers/net/vmxnet3/vmxnet3_drv.c
drivers/net/wireless/iwlwifi/dvm/tx.c
net/ipv6/route.c
The ipv6 route.c conflict is simple, just ignore the 'net' side change
as we fixed the same problem in 'net-next' by eliminating cached
neighbours from ipv6 routes.
The e1000e conflict is an addition of a new statistic in the ethtool
code, trivial.
The vmxnet3 conflict is about one change in 'net' removing a guarding
conditional, whilst in 'net-next' we had a netdev_info() conversion.
The iwlwifi conflict is dealing with a WARN_ON() conversion in
'net-next' vs. a revert happening in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of annotating with a comment, add a lockdep
annotation which also serves as documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The comment about allocating the IEs together with
the BSS struct is no longer true, remove it. Also
fix a typo in the same area.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As Thomas pointed out, cfg80211_get_mesh() is
unused and can be removed.
Cc: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of first checking if a BSS is an MBSS
and then doing the comparisons, inline it all
into the BSS comparison function. This avoids
doing the IE searches twice and is also a lot
less code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When trying to find a hidden SSID, the lookup function
is done wrong; the code is trying to combine the two
lookups into one, and as a consequence doesn't always
find the entry at all. To understand this, consider a
case where multiple BSS entries with the same channel
and BSSID exist but have different SSID length. Then
comparing against the probe response SSID length is
bound to cause problems since the hidden one might be
either zeroed out or zero-length.
To fix this we need to do two lookups for the two ways
to hide SSIDs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of duplicating the rbtree functions, pass
an argument to the compare function. This removes
the code duplication for the two searches.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In per-station statistics, present 32bit counters are too small
for practical purposes - with gigabit speeds, it get overlapped
every few seconds.
Expand counters in the struct station_info to be 64-bit.
Driver can still fill only 32-bit and indicate in @filled
only bits like STATION_INFO_[TR]X_BYTES; in case driver provides
full 64-bit counter, it should also set in @filled
bit STATION_INFO_[TR]RX_BYTES64
Netlink sends both 32-bit and 64-bit counters, if present, to not
break userspace.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[change to also have 32-bit counters if driver advertises 64-bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that mac80211 no longer uses this API, remove
it completely. If anyone needs it again, we can
revert this patch of course, but mac80211 was the
only user right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When waking up from WoWLAN, it is useful to know
what triggered the wakeup. Support reporting the
wakeup reason(s) in cfg80211 (and a pass-through
in mac80211) to allow userspace to know.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The warning here occasionally triggers but we haven't
found the cause yet. It's a valid warning since if it
triggers the SME state got confused, so add the SME
state to it to help narrow it down in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add API to enable drivers to implement MAC address based
access control in AP/P2P GO mode. Capable drivers advertise
this capability by setting the maximum number of MAC
addresses in such a list in wiphy->max_acl_mac_addrs.
An initial ACL may be given to the NL80211_CMD_START_AP
command and/or changed later with NL80211_CMD_SET_MAC_ACL.
Black- and whitelists are supported, but not simultaneously.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
[rewrite commit log, many cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In commit "cfg80211: check radar interface combinations" a regression
was introduced which might lead to NULL dereference if the argument
chan = NULL, which might happen in IBSS/wext case (and probably
others).
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We do a:
sprintf(buf, " Last beacon: %ums ago",
elapsed_jiffies_msecs(bss->ts));
elapsed_jiffies_msecs() can return a 10 digit number so "buf" needs to
be 31 characters long.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To ease further DFS development regarding interface combinations, use
the interface combinations structure to test for radar capabilities.
Drivers can specify which channel widths they support, and in which
modes. Right now only a single AP interface is allowed, but as the
DFS code evolves other combinations can be enabled.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The NL80211_ATTR_USE_MFP attribute was originally added for
NL80211_CMD_ASSOCIATE, but it is actually as useful (if not even more
useful) with NL80211_CMD_CONNECT, so process that attribute with the
connect command, too.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As per email discussion Jouni Malinen pointed out that:
"P2P message exchanges can be executed on the current operating channel
of any operation (both P2P and non-P2P station). These can be on 5 GHz
and even on 60 GHz (so yes, you _can_ do GO Negotiation on 60 GHz).
As an example, it would be possible to receive a GO Negotiation Request
frame on a 5 GHz only radio and then to complete GO Negotiation on that
band. This can happen both when connected to a P2P group (through client
discoverability mechanism) and when connected to a legacy AP (assuming
the station receive Probe Request frame from full scan in the beginning
of P2P device discovery)."
This means that P2P messages can be sent over different radio devices.
However, these should use the same P2P device address so it should be
able to provision this from user-space. This patch adds a parameter for
this to struct vif_params which should only be used during creation of
the P2P device interface.
Cc: Jouni Malinen <j@w1.fi>
Cc: Greg Goldman <ggoldman@broadcom.com>
Cc: Jithu Jance <jithu@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[add error checking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the nl80211_mesh_power_mode enumeration which holds possible
values for the mesh power mode. These modes are unknown, active,
light sleep and deep sleep.
Add power_mode entry to the mesh config structure to hold the
user-configured default mesh power mode. This value will be used
for new peer links.
Add the dot11MeshAwakeWindowDuration value to the mesh config.
The awake window is a duration in TU describing how long the STA
will stay awake after transmitting its beacon in PS mode.
Add access routines to:
- get/set local link-specific power mode (STA)
- get remote STA's link-specific power mode (STA)
- get remote STA's non-peer power mode (STA)
- get/set default mesh power mode (mesh config)
- get/set mesh awake window duration (mesh config)
All config changes may be done at mesh runtime and take effect
immediately.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com>
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
[fix commit message line length, error handling in set station]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the default mesh beacon interval and DTIM period to cfg80211
and make them accessible to nl80211. This enables setting both
values when joining an MBSS.
Previously the DTIM parameter was not set by mac80211 so the
driver's default value was used.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ranges are taken from IEEE 802.11-2012, common sense or current
implementation requirements.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Acked-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
Documentation/networking/ip-sysctl.txt
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
Both conflicts were simply overlapping context.
A build fix for qlcnic is in here too, simply removing the added
devinit annotations which no longer exist.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since:
commit 2c60db0370
Author: Eric Dumazet <edumazet@google.com>
Date: Sun Sep 16 09:17:26 2012 +0000
net: provide a default dev->ethtool_ops
wireless core does not correctly assign ethtool_ops.
After alloc_netdev*() call, some cfg80211 drivers provide they own
ethtool_ops, but some do not. For them, wireless core provide generic
cfg80211_ethtool_ops, which is assigned in NETDEV_REGISTER notify call:
if (!dev->ethtool_ops)
dev->ethtool_ops = &cfg80211_ethtool_ops;
But after Eric's commit, dev->ethtool_ops is no longer NULL (on cfg80211
drivers without custom ethtool_ops), but points to &default_ethtool_ops.
In order to fix the problem, provide function which will overwrite
default_ethtool_ops and use it by wireless core.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 1a9193185f "regulatory: code cleanup"
changed is_ht40_allowed without considering that IEEE80211_CHAN_NO_HT40 is
not just one flag, but two.
This is causing HT40- to be blocked completely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My commit 379b82f4c9
("regulatory: pass new regdomain to reset function")
broke the restore_regulatory_settings() function due
to a logic change. Consider this change:
- reset_regdomains(true);
- cfg80211_regdomain = cfg80211_world_regdom;
+ reset_regdomains(true, cfg80211_world_regdom);
This looks innocent enough, until you realise that the
called function (reset_regdomains) also resets the
cfg80211_world_regdom pointer, so that the old version
of the code would use the new object it pointed to and
the new version of the code uses the old object. This
lead to a double-free of this object.
Since reset_regdomains() sets it to &world_regdom, use
that directly.
Reported-by: Sujith Manoharan <sujith@msujith.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Reported-by: Bob Copeland <me@bobcopeland.com>
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The uevent callback doesn't protect its access to
last_request, which now causes a warning since
the conversion to get_last_request(). Fix this by
allowing to use RCU protection for last_request.
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following changes are invalid and should be
disallowed when a station already exists:
* supported rates changes, except for TDLS peers
* listen interval changes
* HT capability changes
Disallow them and also update a mac80211 comment
explaining how they would be racy.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Today, stations are added already associated. That is
inefficient if, for example, the driver has no room
for stations any more because then the station will
go through the entire auth/assoc handshake, only to
be kicked out afterwards.
To address this a bit better, at least with drivers
using the new station state callback, allow hostapd
to add stations in unauthenticated mode, just after
receiving the AUTH frame, before even replying. Thus
if there's no more space at that point, it can send
a negative auth frame back. It still needs to handle
later state transition errors though, of course.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should not add new beacon hints even if the wiphy
is not world roaming. Without this we were always adding
a beacon hint if not world roaming for every non world
roaming wiphy interface.
Tested-by: Ben Greear <greearb@candelatech.com>
Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[fix locking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will be used later by other code. This has no
functional change.
Tested-by: Ben Greear <greearb@candelatech.com>
Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Regulatory beacon hints are used to help with world roaming
and as it is right now we learn from a beacon hint processed
on one wiphy to all other wiphys. The processing of beacon
hints however is scheduled and if we have a lot of interfaces
we may hit the case that we'll queue a the same beacon hint
many times until its processed.
To avoid this do a lookup on the queued up beacon hints prior
to adding a new beacon hint. If the beacon hint is removed
from the pending reg beacon hint list then it would be processed
and we'd ensure all wiphys would have learned from it, if its
on the pending reg beacon list we'd now find it prior to it
being processed.
Tested-by: Ben Greear <greearb@candelatech.com>
Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of returning an error and filling a pointer
return the pointer and an ERR_PTR value in error cases.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will allow making freq_reg_info() lock-free.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To simplify the locking and not require cfg80211_mutex
(which nl80211 uses to access the global regdomain) and
also to make it possible for drivers to access their
wiphy->regd safely, use RCU to protect these pointers.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of assigning after calling the function do
it inside the function. This will later avoid a
period of time where the pointer is NULL.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel bandwidth handling isn't really quite right,
it assumes that a 40 MHz channel is really two 20 MHz
channels, which isn't strictly true. This is the way the
regulatory database handling is defined right now though
so remove the logic to handle other channel widths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a bug with the world regulatory domain, it
can be updated any time which is different from all
other regdomains that can only be updated once after
a request for them. Fix this by adding a check for
"processed" to the reg_is_valid_request() function
and clear that when doing a request.
While looking at this I also found another locking
bug, last_request is protected by the reg_mutex not
the cfg80211_mutex so the code in nl80211 is racy.
Remove that code as it only tries to prevent an
allocation in an error case, which isn't necessary.
Then the function can also become static and locking
in nl80211 can have a smaller scope.
Also change __set_regdom() to do the checks earlier
and not different for world/other regdomains.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wiphy_apply_custom_regulatory() doesn't have to hold
the regulatory mutex as it only modifies the given
wiphy with the given regulatory domain, it doesn't
access any global regulatory data.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Many places that currently check that cfg80211_mutex
is held don't actually use any data protected by it.
The functions that need to hold the cfg80211_mutex
are the ones using the cfg80211_regdomain variable,
so add the lock assertion to those and clarify this
in the comments.
The reason for this is that nl80211 uses the regdom
without being able to hold reg_mutex.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function itself has dual-purpose: it can
retrieve from a given regdomain or from the
globally installed one. Change it to have a
single purpose only: to look up from a given
regdomain. Pass the correct regdomain in the
freq_reg_info() function instead.
This also changes the locking rules for it,
no locking is required any more.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even if it never happens and is hidden behind the
debug config option, it's completely useless: the
calltrace will only show module loading.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
toupper() only modifies lower-case letters, so
the isalpha() check is redundant; remove it.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use list_splice_tail_init() and also simplify the locking.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code is a bit too BUG_ON happy, remove all
instances and while doing so make some code a bit
smarter by passing the right pointer instead of
indices into arrays.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is pretty much useless since get_wiphy_idx()
always returns true since it's always called with
a valid wiphy pointer.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of treating special error codes specially,
like -EALREADY, introduce a real enum for all the
needed possibilities and use it.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It would be a major problem if anything were to run
concurrently while the module is being unloaded so
remove the locking that doesn't help anything.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clean up various things like indentation, extra
parentheses, too many/few line breaks, etc.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to unlock before calling
queue_regulatory_request(), so simplify
the function.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to test whether a list is
empty or not before iterating.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use ERR_PTR/IS_ERR to return the result or errors,
also do some code cleanups.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the dummy_rule (also renamed from irule) is only
used for output by the reg_rules_intersect() function
there's no need to clear it at all, remove that.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to allocate one reg rule more
than will be used, reduce the allocations. The
allocation in nl80211 already doesn't allocate
too much space.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When intersecting rules, we count first to know how many
rules need to be allocated, and then do the intersection
into the allocated array. However, the code doing this
writes past the end of the array because it attempts to
do all intersections. Make it stop when the right number
of rules has been reached.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
CONFIG_HOTPLUG is always enabled now, so remove the unused code that was
trying to be compiled out when this option was disabled, in the
networking core.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For channels wider than 20 MHz OFDM will be used, so when
checking whether or not a channel is usable, check for the
no-OFDM flag if the channel is wider than 20 MHz.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix an error on mesh join when no channel has been
explicitly set beforehand.
Also remove a double semicolon.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a BSS struct is updated, the IEs are currently
overwritten or freed. This can lead to races if some
other CPU is accessing the BSS struct and using the
IEs concurrently.
Fix this by always allocating the IEs in a new struct
that holds the data and length and protecting access
to this new struct with RCU.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The cmp_bss() comparator function uses memcmp() to
compare the SSID. This means that cmp_hidden_bss()
needs to similarly return a number bigger than zero
(use 1) instead of -1 when ie1 is bigger than ie2,
which is the case if an ie2 byte is non-zero.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to stop the machine, just leak
the BSS entry if there's an issue with its hold
counter when freeing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is a standalone if, seems to be a regression of commit
"nl80211/cfg80211: add VHT MCS support".
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The CQM TX-error rate/interval can't be less than
zero since they're unsigned values, remove checks.
Also fix indentation of the function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a driver supports P2P GO powersave, allow it to
set the new feature flags for it and allow userspace
to configure the parameters for it. This can be done
at GO startup and later changed with SET_BSS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some of the chandef checking that we do in cfg80211
to check if a channel is supported or not is also
needed in mac80211, so rework that a bit and export
the functions that are needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, e.g. probe_status, there were spaces
missing so the trace output was confusing. Also make
it more like mac80211 when printing netdevs/wiphys
to make reading a combined log easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for reporting and calculating VHT MCSes.
Note that I'm not completely sure that the bitrate
calculations are correct, nor that they can't be
simplified.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change nl80211 to support specifying a VHT (or HT)
using the control channel frequency (as before) and
new attributes for the channel width and first and
second center frequency. The old channel type is of
course still supported for HT.
Also change the cfg80211 channel definition struct
to support these by adding the relevant fields to
it (and removing the _type field.)
This also adds new helper functions:
- cfg80211_chandef_create to create a channel def
struct given the control channel and channel type,
- cfg80211_chandef_identical to check if two channel
definitions are identical
- cfg80211_chandef_compatible to check if the given
channel definitions are compatible, and return the
wider of the two
This isn't entirely complete, but that doesn't matter
until we have a driver using it. In particular, it's
missing
- regulatory checks on the usable bandwidth (if that
even makes sense)
- regulatory TX power (database can't deal with it)
- a proper channel compatibility calculation for the
new channel types
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.
Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.
Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function cfg80211_get_p2p_attr() can fail and returns
a negative error code. However, the return type is unsigned
int. The largest positive number is determined by desired_len
variable in the function, which is u16. So changing the return
type to int to allow easy error checking. Also change the type
for the attribute to enum for improved type checking.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[fix indentation, don't use u8 attr variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, mac80211 checks the DS params IE if present and
uses it for the (primary) BSS channel, instead of the one
that the frame was received on. This is particularly useful
in the 2.4 GHz band since a frame is often received on one
of the adjacent channels due to overlap.
Move this code to cfg80211 so other drivers also do this.
Additionally, on 5 GHz, in particular with some (possibly)
upcoming changes in 802.11ai and duplicate transmissions
when wider channels are used, something similar happens.
So if present, also use the (primary) channel information
contained in the HT operation IE.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The NL80211_CMD_TDLS_OPER command was previously used only for userspace
request for the kernel code to perform TDLS operations. However, there
are also cases where the driver may need to request operations from
userspace, e.g., when using security on the AP path. Add a new cfg80211
function for generating a TDLS operation event for drivers to request a
new link to be set up (NL80211_TDLS_SETUP) or an existing link to be
torn down (NL80211_TDLS_TEARDOWN). Drivers can optionally use these
events, e.g., based on noticing data traffic being sent to a peer
station that is seen with good signal strength.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to ask the user about lib80211
since it will be selected by drivers requiring
it, hide it from Kconfig.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When in world roaming mode, allow 40 MHz to be used
on channels 12 and 13 so that an AP that is, e.g.,
using HT40+ on channel 9 (in the UK) can be used.
Cc: stable@vger.kernel.org
Reported-by: Eddie Chapman <eddie@ehuk.net>
Tested-by: Eddie Chapman <eddie@ehuk.net>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The userspace may want to know what is the current ssid that a given
interface is using. This patch enables nl80211 to send the
NL80211_ATTR_SSID attribute in nl80211_send_iface().
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Store the configured ssid in wdev->ssid when starting an AP
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Parsing the P2P attributes can be tricky as their
contents can be split across multiple (vendor) IEs.
Thus, it's not possible to parse them like IEs (by
returning a pointer to the data.) Instead, provide
a function that copies the attribute data into a
caller-provided buffer and returns the size needed
(useful in case the buffer was too small.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The commit:
commit 5e760230e4
Author: Johannes Berg <johannes.berg@intel.com>
Date: Fri Nov 4 11:18:17 2011 +0100
cfg80211: allow registering to beacons
allowed only a single process to register for beacon events
per wiphy. This breaks cases where a user may want two or
more VIFs on a wiphy and run a seperate hostapd process on
each vif.
This patch allows multiple beacon listeners, fixing the
regression.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This command triggers a new callback: set_mcast_rate(). It enables
the user to change the rate used to send multicast frames for vif
configured as IBSS or MESH_POINT
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TX power setting is currently per wiphy (hardware
device) but with multi-channel capabilities that doesn't
make much sense any more.
Allow drivers (and mac80211) to advertise support for
per-interface TX power configuration. When the TX power
is configured for the wiphy, the wdev will be NULL and
the driver can still handle that, but when a wdev is
given the TX power can be set only for that wdev now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Setting the wdev to NULL when the channel can't be
set for that interface type (to treat the channel
setting for the wiphy/monitor) currently works, but
is confusing in the code if netdev/wdev aren't both
set/unset in the same way. Move the check whether
the channel can be set to where it's needed so that
wdev and netdev are always both assigned or NULL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A number of places in the mesh code don't check that
the frame data is present and in the skb header when
trying to access. Add those checks and the necessary
pskb_may_pull() calls. This prevents accessing data
that doesn't actually exist.
To do this, export ieee80211_get_mesh_hdrlen() to be
able to use it in mac80211.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh header can have address extension by a 4th
or a 5th and 6th address, but never both. Drop such
frames in 802.11 -> 802.3 conversion along with any
frames that have the wrong extension.
Cc: stable@vger.kernel.org
Reviewed-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These were missed due to the tracing work having
started on a kernel that didn't have P2P Device
yet, implement them now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few places touch chan->max_power based on updated tx power rules, but
forget to do the same to chan->max_reg_power.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No driver initializes chan->max_antenna_gain to something sensible, and
the only place where it is being used right now is inside ath9k. This
leads to ath9k potentially using less tx power than it can use, which can
decrease performance/range in some rare cases.
Rather than going through every single driver, this patch initializes
chan->orig_mag in wiphy_register(), ignoring whatever value the driver
left in there. If a driver for some reason wishes to limit it independent
from regulatory rulesets, it can do so internally.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Also add tracing to the API functions that drivers
(and mac80211) can call in cfg80211.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add tracing to make debugging cfg80211/mac80211
(or full-mac driver) interaction easier.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Hila Gonen <hila.gonen@intel.com>
Tested-by: Hila Gonen <hila.gonen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[add a cast to int to sizeof() to avoid warning]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will allow adding central tracing like in mac80211.
Signed-off-by: Hila Gonen <hila.gonen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, a user is allowed to choose a HT operating channel
with WEP when creating an IBSS network. WEP is not allowed
in HT configuration - this patch ensures that such requests
are denied.
Signed-off-by: Sujith Manoharan <c_manoha@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an NL80211_SCAN_FLAG_FLUSH flag that causes old bss cache
entries to be flushed on scan completion. This is useful for
collecting guaranteed fresh scan/survey result (e.g. on resume).
For normal scan, flushing only happens on successful completion
of a scan; i.e. it does not happen if the scan is aborted.
For scheduled scan, previous scan results are flushed everytime
when we get new scan results.
This feature is enabled by default. Drivers can disable it by
unsetting the NL80211_FEATURE_SCAN_FLUSH flag.
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Tested-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
[invert polarity of feature flag to account for old kernels]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add NL80211_SCAN_FLAG_LOW_PRIORITY flag support. It tells drivers
that this is a low priority scan request, so that they can take
necessary action.
Drivers need to advertise low priority scan capability during
registration.
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Tested-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
bss_release() and __cfg80211_unlink_bss() function definitions
are moved at the begining of the file. They are used in next
patch in this series.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a flags word to direct and scheduled scan requests; it will
be used for control of optional behaviours such as flushing the
bss cache prior to doing a scan.
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Tested-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SAE extends Authentication frames with fields that are not information
elements. NL80211_ATTR_IE is not suitable for these, so introduce a new
attribute that can be used to specify the fields needed for SAE in
station mode.
Signed-off-by: Jouni Malinen <j@w1.fi>
[change to verify that SAE is only used with authenticate command]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid situation when we are on associate state in mac80211 and
on disassociate state in cfg80211. This can results on crash
during modules unload (like showed on this thread:
http://marc.info/?t=134373976300001&r=1&w=2) and possibly other
problems.
Reported-by: Pedro Francisco <pedrogfrancisco@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John W. Linville says:
====================
Here is another batch of updates intended for 3.7...
Highlights include an hci_connect re-write in Bluetooth, HCI/LLC
layer separation in NFC, removal of the raw pn544 NFC driver, NFC LLCP
raw sockets support, improved IBSS auth frame handling in mac80211,
full-MAC AP mode notification support in mac80211, a lot of attention
paid to brcmfmac, and the usual level of updates to iwlwifi, ath9k,
mwifiex, and rt2x00, and various other updates.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/team/team.c
drivers/net/usb/qmi_wwan.c
net/batman-adv/bat_iv_ogm.c
net/ipv4/fib_frontend.c
net/ipv4/route.c
net/l2tp/l2tp_netlink.c
The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.
qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.
With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>
The current regulatory code on cfg80211 performs a check to
see if a regulatory rule belongs to an IEEE band so that if
a Country IE is received and no rules are specified for a
band (which is allowed by IEEE) those bands are left intact.
The current band check assumes a rule is bound to a band
if the rule's start or end frequency is less than 2 GHz
apart from the center of frequency being inspected.
In order to support 60 GHz for 802.11ad we need to increase
this to account for the channel spacing of 2160 MHz whereby
a channel somewhere in the middle of a regulatory rule may
be more than 2 GHz apart from either the beginning or
end of the frequency rule.
Without a fix for this even though channels 1-3 are allowed world
wide on the rule (57240 - 63720 @ 2160), channel 2 at 60480 MHz
will end up getting disabled given that it is 3240 MHz from
both the frequency rule start and end frequency. Fix this by
using 2 GHz separation assumption for the 2.4 and 5 GHz bands
but for 60 GHz use a 10 GHz separation before assuming a rule
is not part of the band.
Since we have no 802.11ad drivers yet merged this change has
no impact to existing Linux upstream device drivers.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When call_crda() is called we kick off a witch hunt search
for the same regulatory domain on our internal regulatory
database and that work gets kicked off on a workqueue, this
is done while the cfg80211_mutex is held. If that workqueue
kicks off it will first lock reg_regdb_search_mutex and
later cfg80211_mutex but to ensure two CPUs will not contend
against cfg80211_mutex the right thing to do is to have the
reg_regdb_search() wait until the cfg80211_mutex is let go.
The lockdep report is pasted below.
cfg80211: Calling CRDA to update world regulatory domain
======================================================
[ INFO: possible circular locking dependency detected ]
3.3.8 #3 Tainted: G O
-------------------------------------------------------
kworker/0:1/235 is trying to acquire lock:
(cfg80211_mutex){+.+...}, at: [<816468a4>] set_regdom+0x78c/0x808 [cfg80211]
but task is already holding lock:
(reg_regdb_search_mutex){+.+...}, at: [<81646828>] set_regdom+0x710/0x808 [cfg80211]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (reg_regdb_search_mutex){+.+...}:
[<800a8384>] lock_acquire+0x60/0x88
[<802950a8>] mutex_lock_nested+0x54/0x31c
[<81645778>] is_world_regdom+0x9f8/0xc74 [cfg80211]
-> #1 (reg_mutex#2){+.+...}:
[<800a8384>] lock_acquire+0x60/0x88
[<802950a8>] mutex_lock_nested+0x54/0x31c
[<8164539c>] is_world_regdom+0x61c/0xc74 [cfg80211]
-> #0 (cfg80211_mutex){+.+...}:
[<800a77b8>] __lock_acquire+0x10d4/0x17bc
[<800a8384>] lock_acquire+0x60/0x88
[<802950a8>] mutex_lock_nested+0x54/0x31c
[<816468a4>] set_regdom+0x78c/0x808 [cfg80211]
other info that might help us debug this:
Chain exists of:
cfg80211_mutex --> reg_mutex#2 --> reg_regdb_search_mutex
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(reg_regdb_search_mutex);
lock(reg_mutex#2);
lock(reg_regdb_search_mutex);
lock(cfg80211_mutex);
*** DEADLOCK ***
3 locks held by kworker/0:1/235:
#0: (events){.+.+..}, at: [<80089a00>] process_one_work+0x230/0x460
#1: (reg_regdb_work){+.+...}, at: [<80089a00>] process_one_work+0x230/0x460
#2: (reg_regdb_search_mutex){+.+...}, at: [<81646828>] set_regdom+0x710/0x808 [cfg80211]
stack backtrace:
Call Trace:
[<80290fd4>] dump_stack+0x8/0x34
[<80291bc4>] print_circular_bug+0x2ac/0x2d8
[<800a77b8>] __lock_acquire+0x10d4/0x17bc
[<800a8384>] lock_acquire+0x60/0x88
[<802950a8>] mutex_lock_nested+0x54/0x31c
[<816468a4>] set_regdom+0x78c/0x808 [cfg80211]
Reported-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In AP mode, when a station requests connection to an AP and if the
request is failed for particular reason, userspace is notified about the
failure through NL80211_CMD_CONN_FAILED command. Reason for the failure
is sent through the attribute NL80211_ATTR_CONN_FAILED_REASON.
Signed-off-by: Pandiyarajan Pitchaimuthu <c_ppitch@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The only case where intersected_rd can become non NULL is within an if. All
paths from that if return, so the end chunk has therefore squawked its
last and is no more.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is a frequent mistake to confuse the netlink port identifier with a
process identifier. Try to reduce this confusion by renaming fields
that hold port identifiers portid instead of pid.
I have carefully avoided changing the structures exported to
userspace to avoid changing the userspace API.
I have successfully built an allyesconfig kernel with this change.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull in mac80211.git to let the next patch apply
without conflicts, also resolving a hwsim conflict.
Conflicts:
drivers/net/wireless/mac80211_hwsim.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The wext code checks is the event data is within size limits.
When this check fails a message is logged with violating size.
This patch adds the event id to put us on the right track for
resolving that violation.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using list_move_tail() instead of list_del() + list_add_tail().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
connkeys is malloced in nl80211_parse_connkeys() and should
be freed in the error handling case, otherwise it will cause
memory leak.
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support using a different MAC address
for the P2P Device address we must first have a
P2P Device abstraction that can be assigned a MAC
address.
This abstraction will also be useful to support
offloading P2P operations to the device, e.g.
periodic listen for discoverability.
Currently, the driver is responsible for assigning
a MAC address to the P2P Device, but this could be
changed by allowing a MAC address to be given to
the NEW_INTERFACE command.
As it has no associated netdev, a P2P Device can
only be identified by its wdev identifier but the
previous patches allowed using the wdev identifier
in various APIs, e.g. remain-on-channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define the A-MPDU status field in radiotap, also
update the radiotap parser for it and the MCS field
that was apparently missed last time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
libertas currently calls cfg80211_disconnected() when it is being
brought down. This causes an event to be allocated, but since the
wdev is already removed from the rdev by the time that the event
processing work executes, the event is never processed or freed.
http://article.gmane.org/gmane.linux.kernel.wireless.general/95666
Fix this leak, and other possible situations, by processing the event
queue when a device is being unregistered. Thanks to Johannes Berg for
the suggestion.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Cc: stable@vger.kernel.org
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restore the default state to the "beacon_found" flag when
the channel flags are restored. Otherwise, we can end up
with a channel that we can no longer transmit on even when
we can see beacons on that channel.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the only way for wireless drivers to tell whether or not OFDM
is allowed on the current channel is to check the regulatory
information. However, this requires hodling cfg80211_mutex, which is not
visible to the drivers.
Other regulatory restrictions are provided as flags in the channel
definition, so let's do similarly with OFDM. This patch adds a new flag,
IEEE80211_CHAN_NO_OFDM, to tell drivers that OFDM on a channel is not
allowed. This flag is set on any channels for which regulatory indicates
that OFDM is prohibited.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove ah-hoc IE search code found in the ieee80211_bss_get_ie()
and use cfg80211_find_ie() instead.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
commit eccc068e8e
Author: Hong Wu <Hong.Wu@dspg.com>
Date: Wed Jan 11 20:33:39 2012 +0200
wireless: Save original maximum regulatory transmission power for the calucation of the local maximum transmit pow
changed the way we calculate chan->max_power as min(chan->max_power,
chan->max_reg_power). That broke rt2x00 (and perhaps some other
drivers) that do not set chan->max_power. It is not so easy to fix this
problem correctly in rt2x00.
According to commit eccc068e8 changelog, change claim only to save
maximum regulatory power - changing setting of chan->max_power was side
effect. This patch restore previous calculations of chan->max_power and
do not touch chan->max_reg_power.
Cc: stable@vger.kernel.org # 3.4+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
should fix the following issue
[ 3229.815012] [ BUG: lock held when returning to user space! ]
[ 3229.815016] 3.5.0-rc7-wl #28 Tainted: G W O
[ 3229.815017]
------------------------------------------------
[ 3229.815019] wpa_supplicant/5783 is leaving the kernel with locks still held!
[ 3229.815022] 1 lock held by wpa_supplicant/5783:
[ 3229.815023] #0: (reg_mutex){+.+.+.}, at: [<fa65834d>]
reg_last_request_cell_base+0x1d/0x60 [cfg80211]
Cc: Luis Rodriguez <mcgrof@gmail.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Tested-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
regulatory_update() just calls wiphy_update_regulatory().
wiphy_update_regulatory() assumes you already have
the reg_mutex held so just move the call within locking
context and kill the superfluous regulatory_update().
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that we have wiphy_regulatory_register() we can
tuck away the core's regulatory_update() call there
and make it static.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes it clearer what we're doing. This now makes a bit
more sense given that regardless of the wiphy if the cell
base station hint feature is supported we will be modifying the
way the regulatory core behaves.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cellular base stations can provide hints to cfg80211 about
where they think we are. This can be done for example on
a cell phone. To enable these hints we simply allow them
through as user regulatory hints but we allow userspace
to clasify the hint as either coming directly from the
user or coming from a cellular base station. This option
is only available when you enable
CONFIG_CFG80211_CERTIFICATION_ONUS.
The base station hints themselves will not be processed
by the core unless at least one device on the system
supports this feature.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds CONFIG_CFG80211_CERTIFICATION_ONUS which is to
be used for features / code which require a bit of work on
the system integrator's part to ensure that the system will
still pass 802.11 regulatory certification. This option is
also usable for researchers and experimenters looking to add
code in the kernel without impacting compliant code.
We'd use CONFIG_EXPERT alone but it seems that most standard
Linux distributions are enabling CONFIG_EXPERT already. This
allows us to define 802.11 specific kernel features under a
flag that is intended by design to be disabled by standard
Linux distributions, and only enabled by system integrators
or distributions that have done work to ensure regulatory
certification on the system with the enabled features.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While adding regulatory support to ath6kl I noticed that I easily
got the regulatory code confused. The way to reproduce the bug was:
1. iw reg set FI (in userspace)
2. cfg80211 calls ath6kl_reg_notify(FI)
3. ath6kl sets regdomain in firmware
4. firmware sends regdomain event to notify about the new regdomain (FI)
5. ath6kl calls regulatory_hint(FI)
And this (from FI to FI transition) confuses cfg80211 and after that I
only get "Pending regulatory request, waiting for it to be
processed...." messages and regdomain changes won't work anymore.
The reason why ath6kl calls regulatory_hint() is that firmware can change
the regulatory domain by it's own, for example due to 11d IEs. I could
of course workaround this in ath6kl but I think it's better to handle
the case in cfg80211.
The fix is pretty simple, use a different error code if the regdomain is
same and then just set the request processed so that it doesn't block new
requests.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Let the user configure serveral TX error conection quality monitoring
parameters: % error rate, survey interval, and # of attempted packets.
On exceeding the TX failure rate over the given interval, the driver
will send a CQM notify event with the actual TX failure rate and
packets attempted.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In one of my previous patches I erroneously
used nla_put_u32 for the wdev_id, fix that
to use nla_put_u64.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Revert commit b78e8ceac2
("cfg80211: track monitor channel") and remove the
set_monitor_enabled() callback.
Due to the tracking happening in NETDEV_PRE_UP, it had
introduced bugs because the monitor interface callback
would be called before the device was started. It looks
like there's no way to fix this, and using NETDEV_PRE_UP
is broken anyway (since there's no NETDEV_UP_FAIL), so
remove all that code, track interfaces in NETDEV_UP and
also stop tracking the monitor channel in cfg80211.
This mostly reverts to before the tracking, except that
we keep the interface count tracking so that setting the
monitor channel can be rejected properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This essentially reverts commit 2e165b8184 but
introduces the get_channel operation with a new
wireless_dev argument so that you can retrieve
the channel per interface. This is necessary as
even though we can track all interface channels
(except monitor) we can't track the channel type
used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It may be desirable to use WoWLAN without triggers to
keep the connection alive to the AP while suspended.
Allow this use by enabling WoWLAN without triggers if
no triggers were requested.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Without this change, running AP + station on the same wiphy
does not work since the commit "cfg80211: add channel checking
for iface combinations". The stopped AP prevents the client
from connecting to an AP on a different channel.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[line-break commit message to < 72 chars]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To call cfg80211_get_chan_state() we need to lock
the wdev, so we need to lock the wdev_iter mutex
in cfg80211_can_use_iftype_chan(). This needs to
use nested locking for lockdep.
Also, cfg80211_get_chan_state() doesn't actually
use the rdev, so remove that completely including
the lock assertion that isn't needed.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new P2P Device will have to be able to scan for
P2P search, so move scanning to use struct wireless_dev
instead of struct net_device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After a new virtual interface is created, reply
to userspace with a message detailing it so it
knows the new wdev identifier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to be able to create P2P Device wdevs, move
the virtual interface management over to wireless_dev
structures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The management frame and remain-on-channel APIs will be
needed in the P2P device abstraction, so move them over
to the new wdev-based APIs. Userspace can still use both
the interface index and wdev identifier for them so it's
backward compatible, but for the P2P Device wdev it will
be able to use the wdev identifier only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few places that iterate the wdev
list and assume wdev->netdev exists, check
there. The rfkill one has to be extended for
each non-netdev type later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since soon there will be virtual interfaces that
don't have a netdev, use the wdev identifier for
the API to retrieve interface data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some nl80211 callbacks will soon need the wdev instead
of the netdev, so add NL80211_FLAG_NEED_WDEV to allow
them to request that. Add NL80211_FLAG_NEED_WDEV_UP as
well which checks the netdev is UP if one exists.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support a P2P device abstraction and
Bluetooth high-speed AMPs, we need to have a way
to identify virtual interfaces that don't have a
netdev associated.
Do this by adding a NL80211_ATTR_WDEV attribute
to identify a wdev which may or may not also be
a netdev.
To simplify things, use a 64-bit value with the
high 32 bits being the wiphy index for this new
wdev identifier in the nl80211 API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Quick fix for method being invoked without checking its existence.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
60g band uses different from .11n MCS scheme, so bitrate
should be calculated differently
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Until now, a u16 value was used to represent bitrate value.
With VHT bitrates this becomes too small.
Introduce a new 32-bit bitrate attribute. nl80211 will report
both the new and the old attribute, unless the bitrate doesn't
fit into the old u16 attribute in which case only the new one
will be reported.
User space tools encouraged to prefer the 32-bit attribute, if
available (since it won't be available on older kernels.)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[reword commit message and comments a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal's monitor channel tracking introduce a locking problem
as it locked the rdev lock inside the netdev notifier which
isn't allowed as we might already hold it if we get there by
removing an interface that is up.
Fix this by relying only on the RTNL to protect the interface
counters, the RTNL is always held in these code paths anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add regulatory rule for the 60g band
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add enumerations for both cfg80211 and nl80211.
This expands wiphy.bands etc. arrays.
Extend channel <-> frequency translation to cover 60g band
and modify the rate check logic since there are no legacy
mandatory rates (only MCS is used.)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
devlist_mtx locking is changed to accomodate changes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
.connect cannot be handled since the driver scans
and connects on its own. It is up to the driver
then to refuse a connection (with -EBUSY for
example).
Non-fixed channel IBSSes always take a single
channel resource. For example two non-fixed
channel IBSSes always take up 2
num_different_channels, even if they operate on
the same channel at a given point of time.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We do not need it anymore since cfg80211 tracks
monitor channel and monitor channel type.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implements behaviour seen in mac80211. A running
monitor always has a channel - even before
.set_channel. This way we won't break current
behaviour.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make it even more obvious we support single
monitor channel. This will allow us to remove
.get_channel.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Having .set_monitor_channel work with non-monitor
interfaces running would make interface
combinations accounting ambiguous.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implements .set_monitor_enabled(wiphy, enabled).
Notifies driver upon change of interface layout.
If only monitor interfaces become present it is
called with 2nd argument being true. If
non-monitor interface appears then 2nd argument
is false. Driver is notified only upon change.
This makes it more obvious about the fact that
cfg80211 supports single monitor channel. Once we
implement multi-channel we don't want to allow
setting monitor channel while other interface
types are running. Otherwise it would be ambiguous
once we start considering num_different_channels.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Helper function for finding out which channel is
used by a given interface.
An exclusive channel can be used only by a single
interface. This is mainly for non-fixed channel
IBSS handling.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IBSS may hop between channels. It is necessary to
account this special case when considering
interface combinations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to know which channel is used by a running
AP and mesh for channel context accounting and
finding matching/active interface combination.
STA/IBSS have current_bss already which allows us
to check which channel a vif is tuned to.
Non-fixed channel IBSS can be handled with
additional changes.
Monitor mode is going to be handled differently.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll need this for proper channel tracking (which
is going to be needed for channel context
accounting and finding matching/active interface
combination).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This functionality will be reused when interface
is going down. Avoids code duplication. Also adds
missing wdev locking.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using NLMSG_GOODSIZE results in multiple pages being used as
nlmsg_new() will automatically add the size of the netlink
header to the payload thus exceeding the page limit.
NLMSG_DEFAULT_SIZE takes this into account.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow drivers to advertise their VHT capabilities
and export them to userspace via nl80211.
Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When CONFIG_PM is disabled, no device can possibly
support WoWLAN since it can't go to sleep to start
with. Due to this, mac80211 had even rejected the
hardware registration. By making all the code and
data for WoWLAN depend on CONFIG_PM we can promote
this runtime error to a compile-time error.
Add #ifdef around all WoWLAN code to remove it in
systems that don't need it as they never suspend.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support configuring an RSSI threshold in dBm (s32) when requesting
scheduled scan, below which a BSS won't be reported by the cfg80211
driver.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit "cfg80211: provide channel to start_ap function" assumes that the
channel is always passed to the NL80211_CMD_START_AP command, however
in case of multi-BSSID, hostapd only passes the channel for the first vif.
This makes starting beaconing on secondary vifs fail with -EINVAL.
Fix this by storing the channel provided to .start_ap in wdev->preset_chan
and picking the first AP vif's channel for secondary vifs if not provided.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To fix the testmode cross-namespace access problem,
use __cfg80211_rdev_from_attrs() to get the device
instead of open-coding similar functionality.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change the function to __cfg80211_rdev_from_attrs
to take attributes instead of the info struct to
make it usable from dump callbacks for testmode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are currently a few ways to "escape"
the network namespace and access a wiphy
that belongs to another namespace. Add a
netns argument to the relevant functions
to fix this.
One remaining issue with testmode will be
fixed in a follow-up patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As defined in section 13.10.9.3 Case D (802.11-2012), this
control variable is used to limit the mesh STA to send only
one PREQ to a root mesh STA within this interval of time
(in TUs). The default value for this variable is set to
2000 TUs. However, for current implementation, the maximum
configurable of dot11MeshHWMPconfirmationInterval is
restricted by dot11MeshHWMPactivePathTimeout.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the mesh configuration parameters dot11MeshHWMProotInterval
and dot11MeshHWMPactivePathToRootTimeout to be used by
proactive PREQ mechanism.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It should be NL80211_SCHED_SCAN_MATCH_ATTR_SSID as
documented, not NL80211_ATTR_SCHED_SCAN_MATCH_SSID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
fix the coding style related to mesh parameters, especially the indentation,
as pointed out by Johannes Berg.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Don't validate interface combinations on a stopped
interface. Otherwise we might end up being able to
create a new interface with a certain type, but
won't be able to change an existing interface
into that type.
This also skips some other functions when
interface is stopped and changing interface type.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The remain-on-channel time validation shouldn't
depend on the value of HZ, as it does now with
the check against jiffies, since then you might
use a value that works on one system but not on
another. Fix it by checking against a minimum
that's fixed.
Also add validation of the wait duration for a
management frame TX since this also translates
into remain-on-channel internally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we've removed all uses of the set_channel
API except for the monitor channel and in libertas,
clarify this. Split the libertas mesh use into a
new libertas_set_mesh_channel() operation, just to
keep backward compatibility, and rename the normal
set_channel() to set_monitor_channel().
Also describe the desired set_monitor_channel()
semantics more clearly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just like the AP mode patch, instead of setting
the channel and then joining the mesh network,
provide the channel to join the network on to
the join_mesh() function.
Like in AP mode, you can also give the channel
to the join-mesh nl80211 command now.
Unlike AP mode, it picks a default channel if
none was given.
As libertas uses mesh mode interfaces but has
no join_mesh callback and we can't simply break
it, keep some compatibility code for that case
and configure the channel directly for it.
In the non-libertas case, where we store the
channel until join, allow setting it while the
interface is down.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If it worked (Felix says it doesn't right now), the
typical use-case for WDS interfaces would be to be
slaved to AP mode interfaces. Therefore, it isn't
necessary to set the channel on WDS interfaces. As
they don't support powersave or anything like that,
they also couldn't use a different channel anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of setting the channel first and then
starting the AP, let cfg80211 store the channel
and provide it as one of the AP settings.
This means that now you have to set the channel
before you can start an AP interface, but since
hostapd/wpa_supplicant always do that we're OK
with this change.
Alternatively, it's now possible to give the
channel as an attribute to the start-ap nl80211
command, overriding any preset channel.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change cfg80211_can_beacon_sec_chan() to return true
if there is no secondary channel to simplify all the
current users of it. They all check the channel type
before calling the function because it returns false
if there's no secondary channel.
Also actually document the return value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Almost all wireless tools have transitioned to
or at least added compatibility with nl80211 so
there's no real need for CONFIG_CFG80211_WEXT
any more. Mark it for removal, and also change
the default to not be enabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only user of this was hal prior to its 0.5.12
release which happened over two years ago, so I'm
sure this can be removed without issues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a given interface combination doesn't contain
a required interface type then we missed checking
that and erroneously allowed it even though iface
type wasn't there at all. Add a check that makes
sure that all interface types are accounted for.
Cc: stable@kernel.org
Reported-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CFG80211_DEV_WARN_ON() at "net/wireless/ibss.c line 63"
is unnecessarily triggered even after successful connection,
when cfg80211_ibss_joined() is called by driver inside
.join_ibss handler.
This patch fixes the problem by changing 'sme_state' in ibss path
and having WARN_ON() check for 'sme_state' similar to infra
association.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are four instances in nl80211 of getting the
channel type from the attribute and validating it,
refactor those.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It should return bool, not int. The function even
does return true/false.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't really want/need to maintain the old
station flags API any more, so refuse changes
to new (not yet defined) flags from the old
flags API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_calculate_bitrate() doesn't work for MCS
rates 32 or higher, and it has always returned 0
in that case. Warn if it ever really happens.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_calculate_bitrate() is defined in the external
header file cfg80211.h now, so no need to keep it in
the internal one as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed some checkpatch warnings.
Signed-off-by: Cristian Chilipirea <cristian.chilipirea@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Standardize the net core ratelimited logging functions.
Coalesce formats, align arguments.
Change a printk then vprintk sequence to use printf extension %pV.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spatch/coccinelle isn't perfect. It doesn't understand
__aligned(x) and doesn't convert functions it can't parse.
Convert the remaining compare_ether_addr uses.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
I removed a conversion from scan.c/cmp_bss_core
that appears to be a sorting function.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new mesh configuration parameter "ht_opmode" and will
allow user to check the current HT protection mode selected. Users could
configure the protection mode by the command "iw mesh_iface set mesh_param
mesh_ht_protection_mode=2". The default protection mode of mesh is set to
non-HT mixed mode.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the BSS table is organized in a RB tree, the BSSs need to be
comparable. This means that we must define a < and > operator to
the BSS object.
compare_ethr_addr isn't enough since it returns only a binary value.
Since Felix's
cfg80211: use compare_ether_addr on MAC addresses instead of memcmp
Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BSS table is corrupted: rb_find_bss can't find the bss.
As a result BSSes are duplicated in the BSS table, and we get stuck
while probing an AP before associating (in STA mode).
Change-Id: I85928756f4328028230832c1565ece7f412f3843
CC: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix merge between commit 3adadc08cc ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d ("net ax25: Simplify and
cleanup the ax25 sysctl handling")
The former moved around the sysctl register/unregister calls, the
later simply removed them.
With help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Legacy rates are not validated while configuring
tx rateset using iw. So below cmd is accepted by nl80211.
sudo iw wlan2 set bitrates legacy-2.4 1 2 3
Validate legacy rates and return
error if any rate in the rateset is not valid.
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The background scan completion takes more time when the station is
having heavy uplink traffic. The scan state machine decides to fall
back to home channel on every off-channel visit when there are pending
frames in tx queue. bgscan completion took ~30sec on dual band US
regulatory card.
scan period = (20 active channels * probe timeout) +
(12 passive channels * passive probe timeout) +
(32 * timeout on home channel) +
(32 * flush timeout)
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My grand plan to allow drivers to gradually move over
to advertising virtual interface combinations and only
enforce with drivers that do want it enforced doesn't
seem to be working out, only Christian ever added the
advertising (to carl9170), nobody else did.
Begin enforcing combinations in cfg80211 so that users
can rely on the information reported about a device.
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use of "unsigned int" is preferred to bare "unsigned" in net tree.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the current channel is known, add frequency and channel type to
NL80211_CMD_GET_INTERFACE.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware may decide to switch channels while already beaconing, e.g.
in response to a cfg80211 connect request on a different vif. Add this
event to notify userspace when an AP or GO interface has successfully
migrated to a new channel, so it can update its configuration
accordingly.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In WoWLAN, we only get the triggers when we actually get
to suspend. As a consequence, drivers currently don't
know that the device should enable wakeup. However, the
device_set_wakeup_enable() API is intended to be called
when the wakeup is enabled, not later when needed.
Add a new set_wakeup() call to cfg80211 and mac80211 to
allow drivers to properly call device_set_wakeup_enable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report Toffset to userspace.
Let userspace select the mesh synchronization method.
Signed-off-by: Marco Porsch <marco.porsch@s2005.tu-chemnitz.de>
Signed-off-by: Pavel Zubarev <pavel.zubarev@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the plan to change mac80211's queue API to
not map ACs to queues 1:1, it seems necessary to
clarify some APIs that act on ACs rather than on
queues to spell that out explicitly. Do this.
Also verify that the AC number given is valid.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Free extra as done in the error-handling code just above.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nl80211 handling code should ensure as much as
it can that the interface is in a valid state, it
can certainly ensure the interface is running.
Not doing so can cause calls through mac80211 into
the driver that result in warnings and unspecified
behaviour in the driver.
Cc: stable@vger.kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
The station_info struct had demanded dBm signal values, but the
cfg80211 wireless extensions implementation was also accepting
"unspecified" (i.e. RSSI) unit values while the nl80211 code was
completely unaware of them. Resolve this by formally allowing the
"unspecified" units while making nl80211 ignore them.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
This is intended to be the timestamp sent by the
peer in the beacon/probe response, not any form
of host timestamp. Clarify the documentation and
variable names.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Receive background scan period as part of connect
command and pass the same to the driver.
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the signal strength (in dBm only for now) to
frames that are received via nl80211's various
frame APIs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds an attribute, NL80211_ATTR_INACTIVITY_TIMEOUT,
to set the inactivity timeout which can be used to remove the
station in AP mode. This can be passed in NL80211_CMD_START_AP
and used by the drivers which have AP MLME in firmware but
don't support get_station() properly. To disable inactivity
timer in userspace, wpa_s for example, there is a new flag,
NL80211_FEATURE_INACTIVITY_TIMER, in nl80211_feature_flags
through which drivers can register their capability to use
the inactivity timeout to free the stations.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh peer links are established only if average rssi of the peer
candidate satisfies the threshold. This is not in 802.11s specification
but was requested by David Fulgham, an open80211s user. This is a way to avoid
marginal peer links with stations that are barely within range.
This patch adds a new mesh configuration parameter, mesh_rssi_threshold. This
feature is supported only for hardwares that report signal in dBm.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "cfg80211: no cookies in cfg80211_send_XXX()"
Holger Schurig removed the cookies in the calls
from mac80211 to cfg80211, but the ones in the
other direction were left in. Remove them now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AP/GO mode API isn't very clearly defined, it
has "set beacon" and "new beacon" etc.
Modify the API to the following:
* start AP -- all settings
* change beacon -- new beacon data
* stop AP -- stop AP mode operation
This also reflects in the nl80211 API, rename
the commands there correspondingly (but keep
the old names for compatibility.)
Overall, this makes it much clearer what's going
on in the API.
Kalle developed the ath6kl changes, I created
the rest of the patch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ridx" is used as an index into the mcs_mask[] array which has
IEEE80211_HT_MCS_MASK_LEN elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the IBSS network is RSN-protected, let userspace authorize the stations
instead of adding them as AUTHORIZED by default.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed by mac80211 to keep a reference
to a BSS alive for the auth process. Remove the
old version of cfg80211_ref_bss() since it's
not actually used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To track authenticated state seems to have been
a design mistake in cfg80211. It is possible to
have out of band authentication (FT), tracking
multiple authentications caused more problems
than it ever helped, and the implementation in
mac80211 is too complex.
Remove all this complexity, and let userspace
do whatever it wants to, mac80211 can deal with
that just fine. Association is still tracked of
course, but authentication no longer is. Local
auth state changes are thus no longer of value,
so ignore them completely.
This will also help implement SAE -- asking the
driver to do an authentication is now almost
equivalent to sending an authentication frame,
with the exception of shared key authentication
which is still handled completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow to set mcs masks through nl80211. We also allow to set MCS
rates but no legacy rates (and vice versa).
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A mesh node that joins the mesh network is by default a forwarding entity. This patch allows
the mesh node to set as non-forwarding entity. Whenever dot11MeshForwarding is set to 0, the
mesh node can prevent itself from forwarding the traffic which is not destined to him.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems that -Wshadow is no longer default in
sparse runs, but let's fix the warnings anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The local maximum transmit power is the maximum power a wireless device
allowed to transmit. If Power Constraint is presented, the local maximum
power equals to the maximum allowed power defined in regulatory domain
minus power constraint.
The maximum transmit power is maximum power a wireless device capable of
transmitting, and should be used in Power Capability element (7.3.2.16
IEEE802.11 2007).
The transmit power from a wireless device should not greater than the
local maximum transmit power.
The maximum transmit power was not calculated correctly in the current
Linux wireless/mac80211 when Power Constraint is presented.
Signed-off-by: Hong Wu <hong.wu@dspg.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My patch to validate station flags broke compatibility
with the old station flags setting where all flags are
always set at once since it always set the mask as all
possible flags which ended up being rejected later in
the station add/modify code.
Fix by parsing only the current flags in the old flags
attribute -- new applications and new flags should use
(and will now require) the new flags attribute where
the mask is given by the application.
Reported-and-tested-by: Thomas Hilber <ath9k-dev@toh.cx>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wireless will select a different hardware queue based on the
top 3 bits of the diffserv field, for ipv4. Extend that queue
selection mechanism to ipv6, and make the calls orthogonal.
Signed-off-by: Dave Täht <dave.taht@bufferbloat.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Following the tradition we have had with ath5k, ath9k, CRDA,
wireless-regdb I'd like to license this code under the permissive ISC
license for the code sharing purposes with other OSes, it'd sure be nice
to help the landscape in this area. Although I am %82.89 owner of the
regulatory code I have asked every contributor to the regulatory code
and have receieved positive Acked-bys from everyone except two deceased
entities:
o Frans Pop RIP 2010 [0]
- Frans Pop <elendil@planet.nl>
- Frans Pop <fjp@debian.org>
o Nokia RIP February, 11, 2011 [1], [2]
- ext-yuri.ershov@nokia.com
- kalle.valo@nokia.com
Frans Pop's contribution was a simple patch 55f98938, titled,
"wireless: remove trailing space in messages" which just add a \n
to some printk lines. I'm going to treat these additions as
uncopyrightable.
As for the contributions made by employees on behalf of Nokia
my contact point was Petri Karhula <petri.karhula@nokia.com> but
after one month he noted he had not been able to get traction from the
legal department on this request, as such it I proceeded by replacing
their contributions in previous patches.
The end goal is to help a clean rewrite that starts in userspace
that is shared under ISC license which currently is taking place with
the regulatory simulator [3].
[0] http://lists.debian.org/debian-devel/2011/12/msg00263.html
[1] http://press.nokia.com/2011/02/11/nokia-outlines-new-strategy-introduces-new-leadership-operational-structure/
[2] http://NokiaPlanB.com
[3] git://github.com/mcgrof/regsim.git
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mihai Moldovan <ionic@ionic.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Tony Vroon <tony@linx.net>
Acked-by: Pavel Roskin <proski@gnu.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Acked-by: Pat Erley <pat-lkml@erley.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Joe Perches <joe@perches.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: John Gordon <john@devicescape.com>
Acked-by: Simon Barber <protocolmagic@gmail.com>
Acked-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: Jiri Benc <jbenc@upir.cz>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Scott James Remnant <keybuk@google.com>
Acked-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nokia hasn't gotten back to me in over 1 month for a relicense
change request. There are only a few changes that they contributed,
so just reverting their changes but replacing with another set.
This change replaces this commit:
commit 269ac5fd2d
Author: Kalle Valo <kalle.valo@nokia.com>
Date: Tue Dec 1 10:47:15 2009 +0200
cfg80211: indent regulatory messages with spaces
The regulatory messages in syslog look weird:
kernel: cfg80211: Regulatory domain: US
kernel: ^I(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
kernel: ^I(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
kernel: ^I(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
kernel: ^I(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
kernel: ^I(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
kernel: ^I(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
kernel: ^I(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
Indent them with four spaces instead of the tab character to get prettier
output.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Petri Karhula <petri.karhula@nokia.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nokia hasn't gotten back to me in over 1 month for a relicense
change request. There are only a few changes that they contributed,
so just reverting their changes but replacing with another set.
This change replaces this commit:
commit c4c322941c
Author: Yuri Ershov <ext-yuri.ershov@nokia.com>
Date: Tue Jun 29 15:08:08 2010 +0400
cfg80211: Update of regulatory request initiator handling
In some cases there could be possible dereferencing freed pointer. The
update is intended to avoid this issue.
Signed-off-by: Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Petri Karhula <petri.karhula@nokia.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If station info contains a beacon loss count, return
it to userspace.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we restore regulatory settings the world regulatory domain
is properly reset on cfg80211 (or user prefered regulatory domain)
but we were never setting back channel values for drivers that use
WIPHY_FLAG_CUSTOM_REGULATORY. Set these values up again by using
the orig_ channel parameters.
This fixes restoring custom regulatory settings upon disconnect
events.
Cc: compat@orbit-lab.org
Cc: Paul Stewart <pstew@google.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Senthilkumar Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By definition WIPHY_FLAG_STRICT_REGULATORY was intended to allow the
wiphy to adjust itself to the country IE power information if the
card had no regulatory data but we had no way to tell cfg80211 that if
the card also had its own custom regulatory domain (these are typically
custom world regulatory domains) that we want to follow the country IE's
noted values for power for each channel. We add support for this and
document it.
This is not a critical fix but a performance optimization for cards
with custom regulatory domains that associate to an AP with sends
out country IEs with a higher EIRP than the one on the custom
regulatory domain. In practice the only driver affected right now
are the Atheros drivers as they are the only drivers using both
WIPHY_FLAG_STRICT_REGULATORY and WIPHY_FLAG_CUSTOM_REGULATORY --
used on cards that have an Atheros world regulatory domain. Cards
that have been programmed to follow a country specifically will not
follow the country IE power. So although not a stable fix distributions
should consider cherry picking this.
Cc: compat@orbit-lab.org
Cc: Paul Stewart <pstew@google.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Senthilkumar Balasubramanian <senthilb@qca.qualcomm.com>
Reported-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nl80211 station handling code is a bit messy
and doesn't do a lot of validation. It seems like
this could be an issue for drivers that don't use
mac80211 to validate everything.
As cfg80211 doesn't keep station state, move the
validation of allowing supported_rates to change
for TDLS only in station mode to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was evidently missed in the TDLS patch (07ba55d7).
Cc: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All nl80211 commands that need only the wiphy
still allow identifying it by giving an interface
index, except, as Kenny pointed out, the testmode
dump support.
Fix this by looking up the wiphy via the ifidx in
this case as well.
Tested-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Regulatory updates set by CORE are ignored for custom regulatory cards.
Let us notify the changes to the driver, as some drivers uses core hint
to restore its orig_* reg domain setting.
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is quite possible to run into a race in bss timeout where
the drivers see the bss entry just before notifying cfg80211
of a roaming event but it got timed out by the time rdev->event_work
got scehduled from cfg80211_wq. This would result in the following
WARN-ON() along with the failure to notify the user space of
the roaming. The other situation which is happening with ath6kl
that runs into issue is when the driver reports roam to same AP
event where the AP bss entry already got expired. To fix this,
move cfg80211_get_bss() from __cfg80211_roamed() to cfg80211_roamed().
[158645.538384] WARNING: at net/wireless/sme.c:586
__cfg80211_roamed+0xc2/0x1b1()
[158645.538810] Call Trace:
[158645.538838] [<c1033527>] warn_slowpath_common+0x65/0x7a
[158645.538917] [<c14cfacf>] ? __cfg80211_roamed+0xc2/0x1b1
[158645.538946] [<c103354b>] warn_slowpath_null+0xf/0x13
[158645.539055] [<c14cfacf>] __cfg80211_roamed+0xc2/0x1b1
[158645.539086] [<c14beb5b>] cfg80211_process_rdev_events+0x153/0x1cc
[158645.539166] [<c14bd57b>] cfg80211_event_work+0x26/0x36
[158645.539195] [<c10482ae>] process_one_work+0x219/0x38b
[158645.539273] [<c14bd555>] ? wiphy_new+0x419/0x419
[158645.539301] [<c10486cb>] worker_thread+0xf6/0x1bf
[158645.539379] [<c10485d5>] ? rescuer_thread+0x1b5/0x1b5
[158645.539407] [<c104b3e2>] kthread+0x62/0x67
[158645.539484] [<c104b380>] ? __init_kthread_worker+0x42/0x42
[158645.539514] [<c151309a>] kernel_thread_helper+0x6/0xd
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code has been on the list to remove for a long
time, so disable it by default, add a warning to its
Kconfig, and schedule it for removal in 3.5.
The only known dependency, hal, has not required it
since its 0.5.12 release, which was in early 2009
and hal has since been deprecated completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prepare cfg80211 for IBSS HT:
* extend cfg80211 ibss struct with channel_type
* Check if extension channel can be used
* Export can_beacon_sec_chan for use in mac80211 (will be called
from ibss.c later).
Signed-off-by: Alexander Simon <an.alexsimon@googlemail.com>
[siwu@hrz.tu-chemnitz.de: Updates]
* fix cfg80211_can_beacon_ext_chan comment
* remove implicit channel_type enum assumptions
* remove radar channel flags check
* add HT IBSS feature flag
* reword commit message
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes' patch for "cfg80211: fix regulatory NULL dereference"
broke user regulaotry hints and it did not address the fact that
last_request was left populated even if the previous regulatory
hint was stale due to the wiphy disappearing.
Fix user reguluatory hints by only bailing out if for those
regulatory hints where a request_wiphy is expected. The stale last_request
considerations are addressed through the previous fixes on last_request
where we reset the last_request to a static world regdom request upon
reset_regdomains(). In this case though we further enhance the effect
by simply restoring reguluatory settings completely.
Cc: stable@vger.kernel.org
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a theoretical race that if hit will trigger
a crash. The race is between when we issue the first
regulatory hint, regulatory_hint_core(), gets processed
by the workqueue and between when the first device
gets registered to the wireless core. This is not easy
to reproduce but it was easy to do so through the
regulatory simulator I have been working on. This
is a port of the fix I implemented there [1].
[1] a246ccf81f
Cc: stable@vger.kernel.org
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As per 802.11mb 13.9.11.3
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains the configuration changes in nl80211/cfg80211.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MAC addresses have a fixed length. The current
policy allows passing < ETH_ALEN bytes, which
might result in reading beyond the buffer.
Cc: stable@vger.kernel.org
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse reports:
net/wireless/util.c:499:30: error: cannot size expression
net/wireless/util.c:503:30: error: cannot size expression
This is evidently due to the EXPORT_SYMBOL() of the
bridge_tunnel_header and rfc1042 header variables.
Move them to the end of the file to work around the
sparse issue. The error itself from sparse can be
ignored safely, but since sparse stops parsing at
errors, other issues after this would go undetected.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows users to disable features such as HT, HT40,
and to modify the MCS, AMPDU, and AMSDU settings for
drivers that support it.
The MCS, AMPDU, and AMSDU features that may be disabled are
are reported in the phy-info netlink message as a mask.
Attemping to disable features that are not supported will
take no affect, but will not return errors. This is to aid
backwards compatibility in user-space apps that may not be
clever enough to deal with parsing the the capabilities mask.
This patch only enables the infrastructure. An additional
patch will enable the feature in mac80211.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No other driver ever ended up using this, and
the commit forgot to move the prototype so no
driver could have used it. Revert it, if any
driver shows up and needs it it can be moved
again, but until then it's more efficient to
have it in mac80211 where the only user is.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_vlan() sets the output parameter even if it
returns an error, which is a bit odd. Instead,
convert it to use ERR_PTR.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently mac80211 implements these for all devices,
but given restrictions of some devices that isn't
really true, so prepare for being able to remove the
capability for some mac80211 devices.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
User space might want to test if driver supports testmode. Adding testmode
to the list of supported commands makes this easier.
I omitted testmode_dump() in purpose. I assume all drivers implementing
testmode_dump() will also implement testmode_cmd().
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This grants drivers access to the DFS region that a
regulatory domain belongs to.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wireless-regdb now has support for mapping a country to
one DFS region. CRDA sends this to us now so process it
so we can provide that hint to drivers. This will later be
used by code for processing DFS in a way that meets the
criteria for the DFS region the country belongs to.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By the time userspace returns with a response to
the regulatory domain request, the wiphy causing
the request might have gone away. If this is so,
reject the update but mark the request as having
been processed anyway.
Cc: Luis R. Rodriguez <lrodriguez@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass probe-response data from usermode via beacon parameters.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Notify user-space about probe-response offloading support in the driver.
A wiphy flag is used to indicate support and a bitmap of protocols
determines which protocols are supported.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John reported the following warning:
net/wireless/nl80211.c: In function ‘nl80211_tx_mgmt’:
net/wireless/nl80211.c:5286:8: warning: ‘hdr’ may be used uninitialized in this function
Evidently, his version of gcc isn't able to see that
when "msg" is initialized, "hdr" must also be. My
gcc, 4.6.1, can actually see that and doesn't warn.
Simply initialize the variable to NULL. That means
if the compiler was ever right we'll crash though so
isn't really optimal since it may hide warnings from
the compiler when somebody modifies this code in the
future.
Reported-by: John Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just add API to get the channel & report it. Trivial really.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The problem with PSM when a hidden SSID was used was originally
reported by Juuso Oikarinen.
- When generally scanning, the AP is getting a bss entry with
a zero SSID.
- When associating, a probe-req is sent to the AP with the SSID,
and as a result a probe-response is received with the hidden
SSID in place. As a consequence, a second bss entry is created
for the AP, now with the real SSID.
- After association, mac80211 executes ieee80211_recalc_ps(),
but does not switch to powersave because the beacon-ies are missing.
As result, the STA does not ever enter PSM.
The patch merges in beacon ies of hidden bss from beacon to the probe
response, creating a consistent set of ies in place.
Patch is depended on "cfg80211: fix cmp_ies" made by Johannes.
Signed-off-by: Dmitry Tarnyagin <dmitry.tarnyagin@stericsson.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new wifi socket TX capability should be
supported by wifi drivers, let them advertise
whether they do or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For probe responses it can be useful to not wait for ACK to
avoid retransmissions if the station that sent the probe is
already on the next channel, so allow userspace to request
not caring about the ACK with a new nl80211 flag.
Since mac80211 needs to be updated for the new function
prototype anyway implement it right away -- it's just a
few lines of code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The frames are used by AP/STA WDS mode, and hostapd
needs to know when such a frame was received to set
up the VLAN appropriately to allow using it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the ability to register to received beacon frames
to allow implementing OLBC logic in userspace. The
registration is per wiphy since there's no point in
receiving the same frame multiple times.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the AP SME in hostapd is used it wants to
probe the clients when they have been idle for
some time. Add explicit API to support this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the ability to advertise that the device
contains the AP SME and what features it can
support. There are currently no features in
the bitmap -- probe response offload will be
advertised by a few patches Arik is working
on now (who took over from Guy Eilam) and a
device with AP SME will typically implement
and require response offload.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To implement AP mode without monitor interfaces we
need to be able to send a deauth to stations that
send frames without being associated. Enable this
by adding a new nl80211 event for such frames that
an application can subscribe to.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WPI-SMS4 uses 16-octet PN field, so we need to allow longer key
sequence values to be configured.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 4d9d88d1 by Scott James Remnant <keybuk@google.com> added
the .uevent() callback for the regulatory device used during
the platform device registration. The change was done to account
for queuing up udev change requests through udevadm triggers.
The change also meant that upon regulatory core exit we will now
send a uevent() but the uevent() callback, reg_device_uevent(),
also accessed last_request. Right before commiting device suicide
we free'd last_request but never set it to NULL so
platform_device_unregister() would lead to bogus kernel paging
request. Fix this and also simply supress uevents right before
we commit suicide as they are pointless.
This fix is required for kernels >= v2.6.39
$ git describe --contains 4d9d88d1
v2.6.39-rc1~468^2~25^2^2~21
The impact of not having this present is that a bogus paging
access may occur (only read) upon cfg80211 unload time. You
may also get this BUG complaint below. Although Johannes
could not reproduce the issue this fix is theoretically correct.
mac80211_hwsim: unregister radios
mac80211_hwsim: closing netlink
BUG: unable to handle kernel paging request at ffff88001a06b5ab
IP: [<ffffffffa030df9a>] reg_device_uevent+0x1a/0x50 [cfg80211]
PGD 1836063 PUD 183a063 PMD 1ffcb067 PTE 1a06b160
Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
CPU 0
Modules linked in: cfg80211(-) [last unloaded: mac80211]
Pid: 2279, comm: rmmod Tainted: G W 3.1.0-wl+ #663 Bochs Bochs
RIP: 0010:[<ffffffffa030df9a>] [<ffffffffa030df9a>] reg_device_uevent+0x1a/0x50 [cfg80211]
RSP: 0000:ffff88001c5f9d58 EFLAGS: 00010286
RAX: 0000000000000000 RBX: ffff88001d2eda88 RCX: ffff88001c7468fc
RDX: ffff88001a06b5a0 RSI: ffff88001c7467b0 RDI: ffff88001c7467b0
RBP: ffff88001c5f9d58 R08: 000000000000ffff R09: 000000000000ffff
R10: 0000000000000000 R11: 0000000000000001 R12: ffff88001c7467b0
R13: ffff88001d2eda78 R14: ffffffff8164a840 R15: 0000000000000001
FS: 00007f8a91d8a6e0(0000) GS:ffff88001fc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffff88001a06b5ab CR3: 000000001c62e000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process rmmod (pid: 2279, threadinfo ffff88001c5f8000, task ffff88000023c780)
Stack:
ffff88001c5f9d98 ffffffff812ff7e5 ffffffff8176ab3d ffff88001c7468c2
000000000000ffff ffff88001d2eda88 ffff88001c7467b0 ffff880000114820
ffff88001c5f9e38 ffffffff81241dc7 ffff88001c5f9db8 ffffffff81040189
Call Trace:
[<ffffffff812ff7e5>] dev_uevent+0xc5/0x170
[<ffffffff81241dc7>] kobject_uevent_env+0x1f7/0x490
[<ffffffff81040189>] ? sub_preempt_count+0x29/0x60
[<ffffffff814cab1a>] ? _raw_spin_unlock_irqrestore+0x4a/0x90
[<ffffffff81305307>] ? devres_release_all+0x27/0x60
[<ffffffff8124206b>] kobject_uevent+0xb/0x10
[<ffffffff812fee27>] device_del+0x157/0x1b0
[<ffffffff8130377d>] platform_device_del+0x1d/0x90
[<ffffffff81303b76>] platform_device_unregister+0x16/0x30
[<ffffffffa030fffd>] regulatory_exit+0x5d/0x180 [cfg80211]
[<ffffffffa032bec3>] cfg80211_exit+0x2b/0x45 [cfg80211]
[<ffffffff8109a84c>] sys_delete_module+0x16c/0x220
[<ffffffff8108a23e>] ? trace_hardirqs_on_caller+0x7e/0x120
[<ffffffff814cba02>] system_call_fastpath+0x16/0x1b
Code: <all your base are belong to me>
RIP [<ffffffffa030df9a>] reg_device_uevent+0x1a/0x50 [cfg80211]
RSP <ffff88001c5f9d58>
CR2: ffff88001a06b5ab
---[ end trace 147c5099a411e8c0 ]---
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Scott James Remnant <keybuk@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
genlmsg_end() cannot fail, it just returns the length
of the message. Thus, error handling for it is useless.
While removing it, I also noticed a useless variable
and removed this it as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When comparing two items by IE, the sort order
wasn't stable, which could lead to issues in the
rbtree. Make it stable by making a missing IE
sort before a present IE.
Also sort by length first if it differs and then
by contents.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In other modes the parameters should not be set.
Right now, mac80211 will set them, even if the
user asked for setting them on VLANs which the
driver doesn't know about, causing all kinds of
trouble.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the NL80211_ATTR_HT_CAPABILITY attribute is
used as a struct, it needs a minimum, not maximum
length. Enforce that properly. Not doing so could
potentially lead to reading after the buffer.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These files are non modular, but need to export symbols using
the macros now living in export.h -- call out the include so
that things won't break when we remove the implicit presence
of module.h from everywhere.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files were getting access to these two via the implicit
presence of module.h everywhere. They aren't modules, so they
don't need the full module.h inclusion though.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reuse the already existing struct nl80211_sta_flag_update to specify
both, a flag mask and the flag set itself. This means
nl80211_sta_flag_update is now used for setting station flags and also
for getting station flags.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark the STA entries of enabled TDLS peers with a new "peer authorized"
flag.
During link setup, allow special TDLS setup frames through the AP, but
otherwise drop all packets destined to the peer. This is required by the
TDLS (802.11z) specification in order to prevent reordering of MSDUs
between the AP and direct paths.
When setup completes and the peer is authorized, send data directly,
bypassing the AP.
In the Rx path, allow data to be received directly from TDLS peers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When adding a TDLS peer STA, mark it with a new flag in both nl80211 and
mac80211. Before adding a peer, make sure the wiphy supports TDLS and
our operating mode is appropriate (managed).
In addition, make sure all peers are removed on disassociation.
A TDLS peer is first added just before link setup is initiated. In later
setup stages we have more info about peer supported rates, capabilities,
etc. This info is reported via nl80211_set_station().
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for sending high-level TDLS commands and TDLS frames via
NL80211_CMD_TDLS_OPER and NL80211_CMD_TDLS_MGMT, respectively. Add
appropriate cfg80211 callbacks for lower level drivers.
Add wiphy capability flags for TDLS support and advertise them via
nl80211.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when hostapd sets the station as authorized
we also overwrite its uAPSD parameter. This obviously
leads to buggy behaviour (later, with my patches that
actually add uAPSD support). To fix this, only apply
those parameters if they were actually set in nl80211,
and to achieve that add a bitmap of things to apply.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
