The driver currently always sets the PBLx8/PBLx4 bit, which means that
the pbl values configured via the pbl/txpbl/rxpbl DT properties are
always multiplied by 8/4 in the hardware.
In order to allow the DT to configure lower pbl values, while at the
same time not changing behavior of any existing device trees using the
pbl/txpbl/rxpbl settings, add a property to disable the multiplication
of the pbl by 8/4 in the hardware.
Suggested-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC and newer supports independent programmable burst lengths for
DMA tx/rx. Add new optional devicetree properties representing this.
To be backwards compatible, snps,pbl will still be valid, but
snps,txpbl/snps,rxpbl will override the value in snps,pbl if set.
If the IP is synthesized to use the AXI interface, there is a register
and a matching DT property inside the optional stmmac-axi-config DT node
for controlling burst lengths, named snps,blen.
However, using this register, it is not possible to control tx and rx
independently. Also, this register is not available if the IP was
synthesized with, e.g., the AHB interface.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
snps,tso was previously placed under AXI BUS Mode parameters,
suggesting that the property should be in the stmmac-axi-config node.
TSO (TCP Segmentation Offloading) has nothing to do with AXI BUS Mode
parameters, and the parser actually expects it to be in the root node,
not in the stmmac-axi-config.
Also added a note about snps,tso only being available on GMAC4 and newer.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cyclecounter mult and shift values can be calculated based on the
CPTS rfclk frequency and timekeepnig framework provides required algos
and API's.
Hence, calc mult and shift basing on CPTS rfclk frequency if both
cpts_clock_shift and cpts_clock_mult properties are not provided in DT (the
basis of calculation algorithm is borrowed from
__clocksource_update_freq_scale() commit 7d2f944a2b ("clocksource:
Provide a generic mult/shift factor calculation")). After this change
cpts_clock_shift and cpts_clock_mult DT properties will become optional.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add three reset control signals, "mac_core_rst", "mac_ifc_rst" and
"phy_rst".
The following diagram explained how the reset signals work.
SoC
|-----------------------------------------------------
| ------ |
| | cpu | |
| ------ |
| | |
| ------------ AMBA bus |
| GMAC | |
| ---------------------- |
| ------------- mac_core_rst | -------------- | |
| |clock and |-------------->| mac core | | |
| |reset | | -------------- | |
| |generator |---- | | | |
| ------------- | | ---------------- | |
| | ---------->| mac interface | | |
| | mac_ifc_rst | ---------------- | |
| | | | | |
| | | ------------------ | |
| |phy_rst | | RGMII interface | | |
| | | ------------------ | |
| | ---------------------- |
|----------|------------------------------------------|
| |
| ----------
|--------------------- |PHY chip |
----------
The "mac_core_rst" represents "mac core reset signal", it resets
the mac core including packet processing unit, descriptor processing unit,
tx engine, rx engine, control unit.
The "mac_ifc_rst" represents "mac interface reset signal", it resets
the mac interface. The mac interface unit connects mac core and
data interface like MII/RMII/RGMII. After we set a new value of
interface mode, we must reset mac interface to reload the new mode value.
The "mac_core_rst" and "mac_ifc_rst" are both optional to be
backward compatible with the hix5hd2 SoC.
The "phy_rst" represents "phy reset signal", it does a hardware reset
on the PHY chip. This reset signal is optional if the PHY can work well
without the hardware reset.
Add one more clock signal, the existing is MAC core clock,
and the new one is MAC interface clock.
The MAC interface clock is optional to be backward compatible with
the hix5hd2 SoC.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "hix5hd2" is SoC name, add the generic ethernet driver name.
The "hisi-gemac-v1" is the basic version and "hisi-gemac-v2" adds
the SG/TXCSUM/TSO/UFO features.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEES2FAuYbJvAGobdVQPTuqJaypJWoFAlhAJY0THG1rbEBwZW5n
dXRyb25peC5kZQAKCRA9O6olrKklam88B/0dgD2R9D8udVyHnp1CGVrWm+REER49
g6V2ZqIqfxaAFEiQFIhySJJtWYt4vHAC2A3Mwx6yyv9qugYb26LCiSt3XQPlPNY4
yVFpVzOMsFjmSu9PQ7u47b7/IKmqmSuuuQQWm3rDxDQC+KLKmH1TfULXzqDQ/yR/
+gNTvi6Zwfi6rFU7B33I6cT0VhfnWXhbAbBdg4jNmW5WAyz+WT6c9J9oXQMRw5VW
ESTYrU2c+IVK3Z3e0BOmnCytaPrxE6j1OmT0LNsVR5aoXDmK3jDNln/7cPEOCkD3
3t9ub+gqfeaMIjyDI3yBcy75Gjk3mFQMXs/3LVTivwZySgGldOak/iyL
=vXN1
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.10-20161201' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2016-12-01
this is a pull request of 4 patches for net-next/master.
There are two patches by Chris Paterson for the rcar_can and rcar_canfd
device tree binding documentation. And a patch by Geert Uytterhoeven
that corrects the order of interrupt specifiers.
The fourth patch by Colin Ian King fixes a spelling error in the
kvaser_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Armada 3700 is a new ARMv8 SoC from Marvell using same network controller
as older Armada 370/38x/XP. There are however some differences that
needed taking into account when adding support for it:
* open default MBUS window to 4GB of DRAM - Armada 3700 SoC's Mbus
configuration for network controller has to be done on two levels:
global and per-port. The first one is inherited from the
bootloader. The latter can be opened in a default way, leaving
arbitration to the bus controller. Hence filled mbus_dram_target_info
structure is not needed
* make per-CPU operation optional - Recent patches adding RSS and XPS
support for Armada 38x/XP enabled per-CPU operation of the controller
by default. Contrary to older SoC's Armada 3700 SoC's network
controller is not capable of per-CPU processing due to interrupt lines'
connectivity. This patch restores non-per-CPU operation, which is now
optional and depends on neta_armada3700 flag value in mvneta_port
structure. In order not to complicate the code, separate interrupt
subroutine is implemented.
For now, on the Armada 3700, RSS is disabled as the current
implementation depend on the per cpu interrupts.
[gregory.clement@free-electrons.com: extract from a larger patch, replace
some ifdef and port to net-next for v4.10]
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to both DTS (example and actual files), and Linux driver code,
the first interrupt specifier should be the Channel interrupt, while the
second interrupt specifier should be the Global interrupt.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII requires special RX and/or TX delays depending on the actual
hardware circuit/wiring. These delays can be added by the MAC, the PHY
or the designer of the circuit (the latter means that no delay has to
be added by PHY or MAC).
There are 4 RGMII phy-modes used describe where a delay should be
applied:
- rgmii: the RX and TX delays are either added by the MAC (where the
exact delay is typically configurable, and can be turned off when no
extra delay is needed) or not needed at all (because the hardware
wiring adds the delay already). The PHY should neither add the RX nor
TX delay in this case.
- rgmii-rxid: configures the PHY to enable the RX delay. The MAC should
not add the RX delay in this case.
- rgmii-txid: configures the PHY to enable the TX delay. The MAC should
not add the TX delay in this case.
- rgmii-id: combines rgmii-rxid and rgmii-txid and thus configures the
PHY to enable the RX and TX delays. The MAC should neither add the RX
nor TX delay in this case.
Document these cases in the ethernet.txt documentation to make it clear
when to use each mode.
If applied incorrectly one might end up with MAC and PHY both enabling
for example the TX delay, which breaks ethernet TX traffic on 1000Mbit/s
links.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYOAC4AAoJEG4XJFUm622bUYkH/3SSYp6moSdKpVnVPx7ST7yK
t9WHR9IMZFIhD6vq8AK6+8OQr1TgGjHfPu+WZj7CIl8nu53kcgPRi51gg1mndbNg
9N3RbVp06nGbM2VnW8ZIpg3OLIXatZ4c9g3LFvvtyobYvWGJ6W4D79JdlmTG1ELr
XAjInbxFsgon+CwqCMOaAJx8xYp42rBnPRZZvhOq9O33kRw8Umo9UQw0s1U2Vfgx
prxQ6d0GxNAPEe8QiDw/vtBcXWFMOhQeDl8sK70ZcojSn1FY730NsIh/Y86PcQTK
6TsvOL5gg+rd0ln8TZRAslnDrZBAhTEDqUzLQMRJ9VjEj5RFd8eLCSIzHfaroI8=
=4qCH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.10. Major changes:
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the devices added to the tables, the probe will recognize the
switch. This however is not sufficient to make it work properly, other
changes are needed because of incompatibilities.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch derives device tree node from pcie bus layer framework.
Device tree bindings file has been renamed(marvell-sd8xxx.txt ->
marvell-8xxx.txt) to accommodate PCIe changes.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
features printed, all these are quite trivial and tiny. The omap5 jack
detection and gpadc patches are not strictly fixes, but I wanted to get
binding document typo fixed before it pops up on other boards. The
gpadc one liner was in the same series and I applied and pushed it out
already before noticing it could have waited. The list of changes is:
- Fix omap3 SoC features printed
- Make sure OMAP_INTERCONNECT is selected for am43xx only configurations
- Add missing memory node for torpedo
- Initialize uart4_mask properly to avoid writing garbage to PRM registers
- Fix NULL pointer dereference for omap4 volt_data
- Add alias for omap5 gpadc needed by iio drivers
- Enable omap5 jack headset jack detection and fix it's binding typo
- Add missing memory node for logicpd-som-lv
- Fix wrong SMPS6 voltage for VDD-DDR3 for omap5
-----BEGIN PGP SIGNATURE-----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=LgIW
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.9/fixes-for-rc-cycle' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.9-rc cycle. Except for the omap3 fix for the SoC
features printed, all these are quite trivial and tiny. The omap5 jack
detection and gpadc patches are not strictly fixes, but I wanted to get
binding document typo fixed before it pops up on other boards. The
gpadc one liner was in the same series and I applied and pushed it out
already before noticing it could have waited. The list of changes is:
- Fix omap3 SoC features printed
- Make sure OMAP_INTERCONNECT is selected for am43xx only configurations
- Add missing memory node for torpedo
- Initialize uart4_mask properly to avoid writing garbage to PRM registers
- Fix NULL pointer dereference for omap4 volt_data
- Add alias for omap5 gpadc needed by iio drivers
- Enable omap5 jack headset jack detection and fix it's binding typo
- Add missing memory node for logicpd-som-lv
- Fix wrong SMPS6 voltage for VDD-DDR3 for omap5
* tag 'omap-for-v4.9/fixes-for-rc-cycle' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: board-common: fix wrong SMPS6 (VDD-DDR3) voltage
ARM: omap3: Add missing memory node in SOM-LV
ASoC: omap-abe-twl6040: fix typo in bindings documentation
dts: omap5: board-common: enable twl6040 headset jack detection
dts: omap5: board-common: add phandle to reference Palmas gpadc
ARM: OMAP2+: avoid NULL pointer dereference
ARM: OMAP2+: PRM: initialize en_uart4_mask and grpsel_uart4_mask
ARM: dts: omap3: Fix memory node in Torpedo board
ARM: AM43XX: Select OMAP_INTERCONNECT in Kconfig
ARM: OMAP3: Fix formatting of features printed
Signed-off-by: Olof Johansson <olof@lixom.net>
The Aspeed SoCs have two BT interfaces : one is IPMI compliant and the
other is H8S/2168 compliant.
The current ipmi/bt-bmc driver implements the IPMI version and we
should reflect its nature in the compatible node name using
'aspeed,ast2400-ibt-bmc' instead of 'aspeed,ast2400-bt-bmc'. The
latter should be used for a H8S interface driver if it is implemented
one day.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add documentation how devicetree can be used to configure ath9k based
devices.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5c2j
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.9-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Update MAINTAINERS for Intel VMD driver filename
- Update Rockchip rk3399 host bridge driver DTS and resets
- Fix ROM shadow problem that made some video device initialization
fail
* tag 'pci-v4.9-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: VMD: Update filename to reflect move
arm64: dts: rockchip: add three new resets for rk3399 PCIe controller
PCI: rockchip: Add three new resets as required properties
PCI: Don't attempt to claim shadow copies of ROM
- Fix mmc card initialization for hosts not supporting HW busy detection
- Fix mmc_test for sending commands during non-blocking write
MMC host:
- mxs: Avoid using an uninitialized
- sdhci: Restore enhanced strobe setting during runtime resume
- sdhci: Fix a couple of reset related issues
- dw_mmc: Fix a reset controller issue
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mnjf
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix mmc card initialization for hosts not supporting HW busy
detection
- Fix mmc_test for sending commands during non-blocking write
MMC host:
- mxs: Avoid using an uninitialized
- sdhci: Restore enhanced strobe setting during runtime resume
- sdhci: Fix a couple of reset related issues
- dw_mmc: Fix a reset controller issue"
* tag 'mmc-v4.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: mxs: Initialize the spinlock prior to using it
mmc: mmc: Use 500ms as the default generic CMD6 timeout
mmc: mmc_test: Fix "Commands during non-blocking write" tests
mmc: sdhci: Fix missing enhanced strobe setting during runtime resume
mmc: sdhci: Reset cmd and data circuits after tuning failure
mmc: sdhci: Fix unexpected data interrupt handling
mmc: sdhci: Fix CMD line reset interfering with ongoing data transfer
mmc: dw_mmc: add the "reset" as name of reset controller
Documentation: synopsys-dw-mshc: add binding for reset-names
- Fix a host of runtime problems with the Intel
Cherryview driver: suspend/resume needs to be
marshalled properly, and strange effects from BIOS
interaction during suspend/resume need to be
dealt with.
- A single bit was being set wrong in the Aspeed
driver.
- Fix an iProc probe ordering fallout resulting from
v4.9 refactorings for bus population.
- Do not specify a default trigger in the ST Micro
cascaded GPIO IRQ controller: the kernel will moan.
- Make IRQs optional altogether on the STM32 driver,
it turns out not all systems have them or want them.
- Fix a re-probe bug in the i.MX driver, it will
eventually crash if probed repeatedly, not good.
-----BEGIN PGP SIGNATURE-----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=ENR8
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"All is about drivers, no core business going on.
- Fix a host of runtime problems with the Intel Cherryview driver:
suspend/resume needs to be marshalled properly, and strange effects
from BIOS interaction during suspend/resume need to be dealt with.
- A single bit was being set wrong in the Aspeed driver.
- Fix an iProc probe ordering fallout resulting from v4.9
refactorings for bus population.
- Do not specify a default trigger in the ST Micro cascaded GPIO IRQ
controller: the kernel will moan.
- Make IRQs optional altogether on the STM32 driver, it turns out not
all systems have them or want them.
- Fix a re-probe bug in the i.MX driver, it will eventually crash if
probed repeatedly, not good"
* tag 'pinctrl-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl-aspeed-g5: Never set SCU90[6]
pinctrl: cherryview: Prevent possible interrupt storm on resume
pinctrl: cherryview: Serialize register access in suspend/resume
pinctrl: imx: reset group index on probe
pinctrl: stm32: move gpio irqs binding to optional
pinctrl: stm32: remove dependency with interrupt controller
pinctrl: st: don't specify default interrupt trigger
pinctrl: iproc: Fix iProc and NSP GPIO support
pm_rst, aclk_rst, pclk_rst was controlled by ROM code so the software
wasn't needed to control it again in theory. But it didn't work properly,
so we do need to do it again and add enough delay between the assert of
pm_rst and the deassert of pm_rst. The Soc intergrated with this
controller, rk3399, is still under MP test internally, so the backward
compatibility won't be a big deal.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Since there is not enough tcam table entries for every vlan and multicast
address, HNS needs to add support of fuzzy matching of TCAM tables. Adding
the property to mask the bits to be fuzzy matched, so update the bindings
document
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support PHY switching on Amlogic GXL SoCs, add support for
16bit and 32bit registers sizes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Peter Ujfalusi <perter.ujfalusi@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Clean-up the documentation to the bgmac-amac driver, per suggestion by
Rob Herring, and add details for NS2 support.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the documentation for PHY lane swapping. This is a boolean entry to
notify the phy device drivers that the TX/RX lanes need to be swapped.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add reset-names property for binding dw-mmc controller.
It might be used together with "reset" property.
- Note: It must be "reset" as name.
Fixes: d6786fefe8 ("mmc: dw_mmc: add reset support to dwmmc host controller")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
stm32 pinctrl driver could be probed even if no interrupt controller
is defined to manage gpio irqs. Entries related to gpio irq management
are moved to optional.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Lots of fixes, mostly drivers as is usually the case.
1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey
Khoroshilov.
2) Fix element timeouts in netfilter's nft_dynset, from Anders K.
Pedersen.
3) Don't put aead_req crypto struct on the stack in mac80211, from
Ard Biesheuvel.
4) Several uninitialized variable warning fixes from Arnd Bergmann.
5) Fix memory leak in cxgb4, from Colin Ian King.
6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann.
7) Several VRF semantic fixes from David Ahern.
8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper.
9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet.
10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev.
11) Fix stale link state during failover in NCSCI driver, from Gavin
Shan.
12) Fix netdev lower adjacency list traversal, from Ido Schimmel.
13) Propvide proper handle when emitting notifications of filter
deletes, from Jamal Hadi Salim.
14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen.
15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac.
16) Several routing offload fixes in mlxsw driver, from Jiri Pirko.
17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy.
18) Validate chunk len before using it in SCTP, from Marcelo Ricardo
Leitner.
19) Revert a netns locking change that causes regressions, from Paul
Moore.
20) Add recursion limit to GRO handling, from Sabrina Dubroca.
21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon.
22) Avoid accessing stale vxlan/geneve socket in data path, from
Pravin Shelar"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits)
geneve: avoid using stale geneve socket.
vxlan: avoid using stale vxlan socket.
qede: Fix out-of-bound fastpath memory access
net: phy: dp83848: add dp83822 PHY support
enic: fix rq disable
tipc: fix broadcast link synchronization problem
ibmvnic: Fix missing brackets in init_sub_crq_irqs
ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
net/mlx4_en: Save slave ethtool stats command
net/mlx4_en: Fix potential deadlock in port statistics flow
net/mlx4: Fix firmware command timeout during interrupt test
net/mlx4_core: Do not access comm channel if it has not yet been initialized
net/mlx4_en: Fix panic during reboot
net/mlx4_en: Process all completions in RX rings after port goes up
net/mlx4_en: Resolve dividing by zero in 32-bit system
net/mlx4_core: Change the default value of enable_qos
net/mlx4_core: Avoid setting ports to auto when only one port type is supported
net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
...
The MAC is capable of RGMII mode and that is probably a more typical
connection type than GMII today (eg it is used by Marvell Reference
designs for several SOCs). Let DT users specify the standard
phy-connection-type = "rgmii-id";
On a phy node.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We haven't seen a whole lot of fixes for the first two weeks since the merge
window, but here is the batch that we have at the moment.
Nothing sticks out as particularly bad or scary, it's mostly a handful of
smaller fixes to several platforms. The Uniphier reset controller changes
could probably have been delayed to 4.10, but they're not scary and just
plumbing up driver changes that went in during the merge window.
We're also adding another maintainer to Marvell Berlin platforms, to help
out when Sebastian is too busy. Yay teamwork!
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OGbj
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We haven't seen a whole lot of fixes for the first two weeks since the
merge window, but here is the batch that we have at the moment.
Nothing sticks out as particularly bad or scary, it's mostly a handful
of smaller fixes to several platforms. The Uniphier reset controller
changes could probably have been delayed to 4.10, but they're not
scary and just plumbing up driver changes that went in during the
merge window.
We're also adding another maintainer to Marvell Berlin platforms, to
help out when Sebastian is too busy. Yay teamwork!"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
ARM: dts: vf610: fix IRQ flag of global timer
ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
ARM: imx: gpc: Initialize all power domains
arm64: dts: Updated NAND DT properties for NS2 SVK
arm64: dts: uniphier: change MIO node to SD control node
ARM: dts: uniphier: change MIO node to SD control node
reset: uniphier: rename MIO reset to SD reset for Pro5, PXs2, LD20 SoCs
arm64: uniphier: select ARCH_HAS_RESET_CONTROLLER
ARM: uniphier: select ARCH_HAS_RESET_CONTROLLER
arm64: dts: Add timer erratum property for LS2080A and LS1043A
arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
ARM: multi_v7_defconfig: Enable Intel e1000e driver
MAINTAINERS: add myself as Marvell berlin SoC maintainer
bus: qcom-ebi2: depend on ARCH_QCOM or COMPILE_TEST
ARM: dts: fix the SD card on the Snowball
arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
arm64: dts: marvell: fix clocksource for CP110 master SPI0
ARM: mvebu: Select corediv clk for all mvebu v7 SoC
Here are a number of small tty and serial driver fixes for reported
issues for 4.9-rc3. Nothing major, but they do resolve a bunch of
problems with the tty core changes that are in 4.9-rc1, and finally the
atmel serial driver is back working properly.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlgU0WQPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspwmIAoJYQ
5fdXVYgwh59wn0E4xuKWSH84AJ9bTIe3MDED9TrE1rocnLaj9wxIuw==
=os0d
-----END PGP SIGNATURE-----
Merge tag 'tty-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small tty and serial driver fixes for reported
issues for 4.9-rc3. Nothing major, but they do resolve a bunch of
problems with the tty core changes that are in 4.9-rc1, and finally
the atmel serial driver is back working properly.
All have been in linux-next with no reported issues"
* tag 'tty-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial_core: fix NULL struct tty pointer access in uart_write_wakeup
tty: serial_core: Fix serial console crash on port shutdown
tty/serial: at91: fix hardware handshake on Atmel platforms
vt: clear selection before resizing
sc16is7xx: always write state when configuring GPIO as an output
sh-sci: document R8A7743/5 support
tty: serial: 8250: 8250_core: NXP SC16C2552 workaround
tty: limit terminal size to 4M chars
tty: serial: fsl_lpuart: Fix Tx DMA edge case
serial: 8250_lpss: enable MSI for sure
serial: core: fix console problems on uart_close
serial: 8250_uniphier: fix clearing divisor latch access bit
serial: 8250_uniphier: fix more unterminated string
serial: pch_uart: add terminate entry for dmi_system_id tables
devicetree: bindings: uart: Add new compatible string for ZynqMP
serial: xuartps: Add new compatible string for ZynqMP
serial: SERIAL_STM32 should depend on HAS_DMA
serial: stm32: Fix comparisons with undefined register
tty: vt, fix bogus division in csi_J
Here are a number of small USB driver fixes for 4.9-rc3. There is the
usual number of gadget and xhci patches in here to resolved reported
issues, as well as some usb-serial driver fixes and new device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlgU0foPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspqE4Ani3Y
N4J9W4SeXT7ilLLQoeLznUv8AJ4sm/Uy5d4syBa+TVEPuAHXort+vw==
=ICZX
-----END PGP SIGNATURE-----
Merge tag 'usb-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes for 4.9-rc3.
There is the usual number of gadget and xhci patches in here to
resolved reported issues, as well as some usb-serial driver fixes and
new device ids.
All have been in linux-next with no reported issues"
* tag 'usb-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
usb: chipidea: host: fix NULL ptr dereference during shutdown
usb: renesas_usbhs: add wait after initialization for R-Car Gen3
usb: increase ohci watchdog delay to 275 msec
usb: musb: Call pm_runtime from musb_gadget_queue
usb: musb: Fix hardirq-safe hardirq-unsafe lock order error
usb: ehci-platform: increase EHCI_MAX_RSTS to 4
usb: ohci-at91: Set RemoteWakeupConnected bit explicitly.
USB: serial: fix potential NULL-dereference at probe
xhci: use default USB_RESUME_TIMEOUT when resuming ports.
xhci: workaround for hosts missing CAS bit
xhci: add restart quirk for Intel Wildcatpoint PCH
USB: serial: cp210x: fix tiocmget error handling
wusb: fix error return code in wusb_prf()
Revert "Documentation: devicetree: dwc2: Deprecate g-tx-fifo-size"
Revert "usb: dwc2: gadget: fix TX FIFO size and address initialization"
Revert "usb: dwc2: gadget: change variable name to more meaningful"
USB: serial: ftdi_sio: add support for Infineon TriBoard TC2X7
wusb: Stop using the stack for sg crypto scratch space
usb: dwc3: Fix size used in dma_free_coherent()
usb: gadget: f_fs: stop sleeping in ffs_func_eps_disable
...
Renesas RZ/G SoC also have the SCIF, SCIFA, SCIFB, and HSCIF ports and
they seem compatible with the R-Car gen2 SoC in this respect...
Document RZ/G1[ME] (also known as R8A774[35]) SoC bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch Adds the new compatible string for ZynqMP SoC.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of fixes for the uniphier clk driver that was introduced recently, as well as
Kconfig option hiding, module autoloading markings, and a few fixes for clk_hw
based registration patches that went in this merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=mWXv
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"This is the first batch of clk driver fixes for this release.
We have a handful of fixes for the uniphier clk driver that was
introduced recently, as well as Kconfig option hiding, module
autoloading markings, and a few fixes for clk_hw based registration
patches that went in this merge window"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: at91: Fix a return value in case of error
clk: uniphier: rename MIO clock to SD clock for Pro5, PXs2, LD20 SoCs
clk: uniphier: fix memory overrun bug
clk: hi6220: use CLK_OF_DECLARE_DRIVER for sysctrl and mediactrl clock init
clk: mvebu: armada-37xx-periph: Fix the clock gate flag
clk: bcm2835: Clamp the PLL's requested rate to the hardware limits.
clk: max77686: fix number of clocks setup for clk_hw based registration
clk: mvebu: armada-37xx-periph: Fix the clock provider registration
clk: core: add __init decoration for CLK_OF_DECLARE_DRIVER function
clk: mediatek: Add hardware dependency
clk: samsung: clk-exynos-audss: Fix module autoload
clk: uniphier: fix type of variable passed to regmap_read()
clk: uniphier: add system clock support for sLD3 SoC
I was on vacation during the merge window (a long vacation)
but this is a bug fix that should go in and a new driver that shouldn't
hurt anything.
This has been in linux-next for a month or so.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlgKVpoACgkQIXnXXONXERdGBACeONBS0wOf4Rv+bxSOdeJcTwLJ
rmoAoJ2R0BpWE1imvcC+AqXOoqg2c48k
=P4Dz
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.9-2' of git://git.code.sf.net/p/openipmi/linux-ipmi
Pull IPMI updates from Corey Minyard:
"A small bug fix and a new driver for acting as an IPMI device.
I was on vacation during the merge window (a long vacation) but this
is a bug fix that should go in and a new driver that shouldn't hurt
anything.
This has been in linux-next for a month or so"
* tag 'for-linus-4.9-2' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: fix crash on reading version from proc after unregisted bmc
ipmi/bt-bmc: remove redundant return value check of platform_get_resource()
ipmi/bt-bmc: add a dependency on ARCH_ASPEED
ipmi: Fix ioremap error handling in bt-bmc
ipmi: add an Aspeed BT IPMI BMC driver
Pull timer updates from Thomas Gleixner:
"This updates contains:
- A revert which addresses a boot failure on ARM Sun5i platforms
- A new clocksource driver, which has been delayed beyond rc1 due to
an interrupt driver issue which was unearthed by this driver. The
debugging of that issue and the discussion about the proper
solution made this driver miss the merge window. There is no point
in delaying it for a full cycle as it completes the basic mainline
support for the new JCore platform and does not create any risk
outside of that platform"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "clocksource/drivers/timer_sun5i: Replace code by clocksource_mmio_init"
clocksource: Add J-Core timer/clocksource driver
of: Add J-Core timer bindings
I made a mistake as for naming for this block. The MIO block is not
implemented for these 3 SoCs in the first place. The current naming
will be a trouble if an SoC with both MIO and SD-ctrl blocks appear
in the future.
This driver has just been merged in the previous merge window.
Rename it before the release.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
I made a mistake as for naming for this block. The MIO block is not
implemented for these 3 SoCs in the first place. The current naming
will be a trouble if an SoC with both MIO and SD-ctrl blocks appear
in the future.
This driver has just been merged in the previous merge window.
Rename it before the release.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
