emac_mac_start() uses information from the external PHY to program
the MAC, so it makes no sense to call it before the link is up.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regardless of how the external PHY is configured, the internal PHY
(the "SGMII" block) is capable of configuring the SGMII link automatically.
When the external PHY link comes up, regardless of how it is configured,
the SGMII link is configured automatically.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY driver is attached only when the driver calls
phy_connect_direct(). Calling phy_attached_print() to display
information about the PHY driver prior to that point is meaningless.
The interface can be brought down, a new PHY driver can be loaded,
and the interface then brought back up. This is the correct time
to display information about the attached driver.
Since phy_attached_print() also prints information about the
interrupt, that needs to be set as well.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
init_ring(), refill_rx_ring() and start_tx() don't check
if mapping dma memory succeed.
The patch adds the checks and failure handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The limitation to 10/100Mbit speeds on R-Car Gen3 is valid for R-Car H3
ES1.0 only. Check for the exact SoC model to allow 1Gbps on newer
revisions of R-Car H3, and on R-Car M3-W.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables tx and rx clock internal delay modes (TDM and RDM).
This is to address a failure in the case of 1Gbps communication using the
by salvator-x board with the KSZ9031RNX phy. This has been reported to
occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs.
With this change APSR internal delay modes are enabled for
"rgmii-id", "rgmii-rxid" and "rgmii-txid" phy modes as follows:
phy mode | ASPR delay mode
-----------+----------------
rgmii-id | TDM and RDM
rgmii-rxid | RDM
rgmii-txid | TDM
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for 32 bit GEM in
64 bit system. It checks capability at runtime
and uses appropriate buffer descriptor.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro is returning ETIME which means various checks to see if
the returned err is less than zero never work. I believe a -ETIME
should be returned instead.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check on err < 0 is redundant and can be removed. Detected
by CoverityScan, CID#1398318 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check on err < 0 is redundant and can be removed. Detected
by CoverityScan, CID#1398321 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DW GMAC databook says the following about bits in "Register 15 (Interrupt
Mask Register)":
--------------------------->8-------------------------
When set, this bit __disables_the_assertion_of_the_interrupt_signal__
because of the setting of XXX bit in Register 14 (Interrupt
Status Register).
--------------------------->8-------------------------
In fact even if we mask one bit in the mask register it doesn't prevent
corresponding bit to appear in the status register, it only disables
interrupt generation for corresponding event.
But currently we expect a bit different behavior: status bits to be in
sync with their masks, i.e. if mask for bit A is set in the mask
register then bit A won't appear in the interrupt status register.
This was proven to be incorrect assumption, see discussion here [1].
That misunderstanding causes unexpected behaviour of the GMAC, for
example we were happy enough to just see bogus messages about link
state changes.
So from now on we'll be only checking bits that really may trigger an
interrupt.
[1] https://lkml.org/lkml/2016/11/3/413
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Phil Reid <preid@electromag.com.au>
Cc: David Miller <davem@davemloft.net>
Cc: Alexandre Torgue <alexandre.torgue@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On dcbnl callback getpgtccfgtx, the driver should check the ets
capability before ets query command is sent to firmware.
It is valid to return from this void function without changing in/out
parameters, as these parameters are initialized to
DCB_ATTR_VALUE_UNDEFINED.
Fixes: 3a6a931dfb ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Modifying TIR hash should change selected fields bitmask in addition to
the function and key.
Formerly, Only on ethool mlx5e_set_rxfh "ethtoo -X" we would not set this
field resulting in zeroing of its value, which means no packet fields are
used for RX RSS hash calculation thus causing all traffic to arrive in
RQ[0].
On driver load out of the box we don't have this issue, since the TIR
hash is fully created from scratch.
Tested:
ethtool -X ethX hkey <new key>
ethtool -X ethX hfunc <new func>
ethtool -X ethX equal <new indirection table>
All cases are verified with TCP Multi-Stream traffic over IPv4 & IPv6.
Fixes: bdfc028de1 ("net/mlx5e: Fix ethtool RX hash func configuration change")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We don't need to modify our TIRs unless the user requested a change in
the hash function/key, for example when changing indirection only.
Tested:
# Modify TIRs hash is needed
ethtool -X ethX hkey <new key>
ethtool -X ethX hfunc <new func>
# Modify TIRs hash is not needed
ethtool -X ethX equal <new indirection table>
All cases are verified with TCP Multi-Stream traffic over IPv4 & IPv6.
Fixes: bdfc028de1 ("net/mlx5e: Fix ethtool RX hash func configuration change")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When tunneling is used, some virtualizations systems set the (mlx5e) uplink
device to be stacked under upper devices such as bridge or ovs internal
port, where the VTEP IP address used for the encapsulation is set on
that upper device.
In order to support such use-cases, we also deal with a setup where the
egress mirred device isn't representing a port on the HW e-switch to where
the ingress device belongs. We use eswitch service function which returns
the uplink and set it as the egress device of the tc encap rule.
Fixes: a54e20b4fc ("net/mlx5e: Add basic TC tunnel set action for SRIOV offloads")
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We must re-enable RoCE on the e-switch management port (PF) only after destroying
the FDB in its switchdev/offloaded mode. Otherwise, when encapsulation is supported,
this re-enablement will fail.
Also, it's more natural and symmetric to disable RoCE on the PF before we create
the FDB under switchdev mode, so do that as well and revert if getting into error
during the mode change later.
Fixes: 9da34cd34e ('net/mlx5: Disable RoCE on the e-switch management [..]')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Make sure to return error when we failed retrieving the FDB steering
name space. Also, while around, correctly print the error when mode
change revert fails in the warning message.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When we fail to retrieve a hardware steering name-space, the returned error
code should say that this operation is not supported. Align the various
places in the driver where this call is made to this convention.
Also, make sure to warn when we fail to retrieve a SW (ANCHOR) name-space.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As ENOTSUPP is specific to NFS, change the return error value to
EOPNOTSUPP in various places in the mlx5 driver.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Suggested-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
8000 series adapters support filtering VXLAN, NVGRE and GENEVE traffic
based on inner fields, and when the NIC recognises such traffic, it
does not match unencapsulated traffic filters any more. So add catch-
all filters for encapsulated traffic on supporting platforms.
Although recognition of VXLAN and GENEVE is based on UDP ports, and thus
will not occur until the driver (on the primary PF) notifies the
firmware of UDP ports to use, NVGRE will always be recognised, hence
without this patch 8000 series adapters will drop all NVGRE traffic.
Partly based on patches by Jon Cooper <jcooper@solarflare.com>.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rationalise several debug-or-warnings printks using netif_cond_dbg
to make output more consistent.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NIC is switched from full-featured to low-latency, encapsulated
filters are no longer available, and this causes errors. This patch
removes those filters from the filter table on restore.
Also, if filters which are removed by the above, or which we fail to
insert when restoring filters, were UC, MC or broadcast default
filters, invalidate the corresponding vlan->default_filters entry.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"swiotlb buffer is full" errors occur after repeated initialisation of a
device - f.e. suspend/resume or ip link set up/down. This is because memory
mapped using dma_map_single() in ravb_ring_format() and ravb_start_xmit()
is not released. Resolve this problem by unmapping descriptors when
freeing rings.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[simon: reworked]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accessing skb after submitting to input queue can cause
access to stale pointers if the skb ends up being transmitted
and freed by that time.
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PIO buffer allocation can fail for two valid reasons:
- we've run out of them (results in -ENOSPC)
- the NIC configuration doesn't support them (results in -EPERM)
Since both these failures are expected netif_err is excessive.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For DLMs and SLMs on 80/81/83xx, many lane configurations
across different boards are coming up. Also kernel doesn't have
any way to identify board type/info and since firmware does,
just get rid of figuring out lane to serdes config and take
whatever has been programmed by low level firmware.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support to set Rx/Tx queue sizes from ethtool. Fixes
an issue with retrieving queue size. Also sets SQ's CQ_LIMIT
based on configured Tx queue size such that HW doesn't process
SQEs when there is no sufficient space in CQ.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the binding was defined, I was not aware that mt2701 was an earlier
version of the SoC. For sake of consistency, the ethernet driver should
use mt2701 inside the compat string as this is the earliest SoC with the
ethernet core.
The ethernet driver is currently of no real use until we finish and
upstream the DSA driver. There are no users of this binding yet. It should
be safe to fix this now before it is too late and we need to provide
backward compatibility for the mt7623-eth compat string.
Reported-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_get_port_module_status() calls bnxt_update_link() which expects
RTNL to be held. In bnxt_sp_task() that does not hold RTNL, we need to
call it with a prior call to bnxt_rtnl_lock_sp() and the call needs to
be moved to the end of bnxt_sp_task().
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_update_link() is called from multiple code paths. Most callers,
such as open, ethtool, already hold RTNL. Only the caller bnxt_sp_task()
does not. So it is a bug to take RTNL inside bnxt_update_link().
Fix it by removing the RTNL inside bnxt_update_link(). The function
now expects the caller to always hold RTNL.
In bnxt_sp_task(), call bnxt_rtnl_lock_sp() before calling
bnxt_update_link(). We also need to move the call to the end of
bnxt_sp_task() since it will be clearing the BNXT_STATE_IN_SP_TASK bit.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_sp_task(), we set a bit BNXT_STATE_IN_SP_TASK so that bnxt_close()
will synchronize and wait for bnxt_sp_task() to finish. Some functions
in bnxt_sp_task() require us to clear BNXT_STATE_IN_SP_TASK and then
acquire rtnl_lock() to prevent race conditions.
There are some bugs related to this logic. This patch refactors the code
to have common bnxt_rtnl_lock_sp() and bnxt_rtnl_unlock_sp() to handle
the RTNL and the clearing/setting of the bit. Multiple functions will
need the same logic. We also need to move bnxt_reset() to the end of
bnxt_sp_task(). Functions that clear BNXT_STATE_IN_SP_TASK must be the
last functions to be called in bnxt_sp_task(). The common scheme will
handle the condition properly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds a number of tracepoints to paths that are either
considered slow-path or exception-like states, where monitoring or
inspecting them would be desirable.
For bpf(2) syscall, tracepoints have been placed for main commands
when they succeed. In XDP case, tracepoint is for exceptions, that
is, f.e. on abnormal BPF program exit such as unknown or XDP_ABORTED
return code, or when error occurs during XDP_TX action and the packet
could not be forwarded.
Both have been split into separate event headers, and can be further
extended. Worst case, if they unexpectedly should get into our way in
future, they can also removed [1]. Of course, these tracepoints (like
any other) can be analyzed by eBPF itself, etc. Example output:
# ./perf record -a -e bpf:* sleep 10
# ./perf script
sock_example 6197 [005] 283.980322: bpf:bpf_map_create: map type=ARRAY ufd=4 key=4 val=8 max=256 flags=0
sock_example 6197 [005] 283.980721: bpf:bpf_prog_load: prog=a5ea8fa30ea6849c type=SOCKET_FILTER ufd=5
sock_example 6197 [005] 283.988423: bpf:bpf_prog_get_type: prog=a5ea8fa30ea6849c type=SOCKET_FILTER
sock_example 6197 [005] 283.988443: bpf:bpf_map_lookup_elem: map type=ARRAY ufd=4 key=[06 00 00 00] val=[00 00 00 00 00 00 00 00]
[...]
sock_example 6197 [005] 288.990868: bpf:bpf_map_lookup_elem: map type=ARRAY ufd=4 key=[01 00 00 00] val=[14 00 00 00 00 00 00 00]
swapper 0 [005] 289.338243: bpf:bpf_prog_put_rcu: prog=a5ea8fa30ea6849c type=SOCKET_FILTER
[1] https://lwn.net/Articles/705270/
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first seven patches from Or Gerlitz in this series further enhances
the mlx5 SRIOV switchdev mode to support offloading IPv6 tunnels using the
TC tunnel key set (encap) and unset (decap) actions.
Or Gerlitz says:
========================
As part of doing this change, few cleanups are done in the IPv4 code,
later we move to use the full tunnel key info provided to the driver as
the key for our internal hashing which is used to identify cases where
the same tunnel is used for encapsulating multiple flows. As done in the
IPv4 case, the control path for offloading IPv6 tunnels uses route/neigh
lookups and construction of the IPv6 tunnel headers on the encap path and
matching on the outer hears in the decap path.
The last patch of the series enlarges the HW FDB size for the switchdev mode,
so it has now room to contain offloaded flows as many as min(max number
of HW flow counters supported, max HW table size supported).
========================
Next to Or's series you can find several patches handling several topics.
From Mohamad, add support for SRIOV VF min rate guarantee by using the
TSAR BW share weights mechanism.
From Or, Two patches to enable Eth VFs to query their min-inline value for
user-space.
for that we move a mlx5 low level min inline helper function from mlx5
ethernet driver into the core driver and then use it in mlx5_ib to expose
the inline mode to rdma applications through libmlx5.
From Kamal Heib, Reduce memory consumption on kdump kernel.
From Shaker Daibes, code reuse in CQE compression control logic
Thanks,
Saeed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYh7FNAAoJEEg/ir3gV/o+TjsIAL1e92+5eutBS9ZvhMARi+Tc
c2V9V8bG8W1RWWTvx1G0aU4nNjWsr5L8Q8gzqpwhrQITBfgpWd+hlnxQCucyhxC3
AC1qQ+AKREe/C+25D+WJRq34/61ZHEH2rbKZvpZ1O8SuicVPbcvJ9eM+wOEDxwwX
u5C5kWQ0HRtCcnFiiOYkB+0CQPH7m3+ZzZek+jDowrexHMSE+yl8ZNtaSTX9c9QN
bE2cPiCVZd7ufKPIwY8LWHBryyl7sh5P+NqzD633OeiqP/pkZsW9A+czyt+d330f
6XTKOS1PCD+TfHE0sZJT4VMCjICMHrOFbNRZuwcxJQ6NfmwIJZfskX4NLbyGQTI=
=vF7U
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-01-24' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-24-01
The first seven patches from Or Gerlitz in this series further enhances
the mlx5 SRIOV switchdev mode to support offloading IPv6 tunnels using the
TC tunnel key set (encap) and unset (decap) actions.
Or Gerlitz says:
========================
As part of doing this change, few cleanups are done in the IPv4 code,
later we move to use the full tunnel key info provided to the driver as
the key for our internal hashing which is used to identify cases where
the same tunnel is used for encapsulating multiple flows. As done in the
IPv4 case, the control path for offloading IPv6 tunnels uses route/neigh
lookups and construction of the IPv6 tunnel headers on the encap path and
matching on the outer hears in the decap path.
The last patch of the series enlarges the HW FDB size for the switchdev mode,
so it has now room to contain offloaded flows as many as min(max number
of HW flow counters supported, max HW table size supported).
========================
Next to Or's series you can find several patches handling several topics.
From Mohamad, add support for SRIOV VF min rate guarantee by using the
TSAR BW share weights mechanism.
From Or, Two patches to enable Eth VFs to query their min-inline value for
user-space.
for that we move a mlx5 low level min inline helper function from mlx5
ethernet driver into the core driver and then use it in mlx5_ib to expose
the inline mode to rdma applications through libmlx5.
From Kamal Heib, Reduce memory consumption on kdump kernel.
From Shaker Daibes, code reuse in CQE compression control logic
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If requesting msi-x interrupts fails in alx_request_irq we fall back to
a single tx queue and msi or legacy interrupts.
Currently the adapter stops working in this case and we get tx watchdog
timeouts. For reasons unknown the adapter gets confused when we load the
dma adresses to the chip in alx_init_ring_ptrs twice: the first time with
multiple queues and the second time in the fallback case with a single
queue.
To fix this move the the call to alx_reinit_rings (which calls
alx_init_ring_ptrs) after alx_request_irq. At this time it is clear how
much tx queues we have and which dma addresses we use.
Fixes: d768319cd4 ("alx: enable multiple tx queues")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If requesting msi-x interrupts fails we should fall back to msi or
legacy interrupts. However alx_realloc_ressources don't call
alx_init_intr, so we fail to set the right number of tx queues.
This results in watchdog timeouts and a nonfunctional adapter.
Fixes: d768319cd4 ("alx: enable multiple tx queues")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The condition to free the descriptor memory is wrong, we want to free the
memory if it is set and not if it is unset. Invert the test to fix this
issue.
Fixes: b0999223f224b ("alx: add ability to allocate and free alx_napi structures")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the ibmveth driver in a KVM/QEMU based VM, it currently
always prints out a scary error message like this when it is started:
ibmveth 71000003 (unregistered net_device): unable to change
checksum offload settings. 1 rc=-2 ret_attr=71000003
This happens because the driver always tries to enable the checksum
offloading without checking for the availability of this feature first.
QEMU does not support checksum offloading for the spapr-vlan device,
thus we always get the error message here.
According to the LoPAPR specification, the "ibm,illan-options" property
of the corresponding device tree node should be checked first to see
whether the H_ILLAN_ATTRIUBTES hypercall and thus the checksum offloading
feature is available. Thus let's do this in the ibmveth driver, too, so
that the error message is really only limited to cases where something
goes wrong, and does not occur if the feature is just missing.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the drivers/net/ethernet/{Makefile,Kconfig} file to make them a
part of the network drivers build.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definitions that support receive side scaling.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the driver interfaces required for support by the ethtool utility.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions to interface with the hardware and some utility functions.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add common functions for Atlantic hardware abstraction layer.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions that handle the PCI bus interface.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions to manululate the vector of receive and transmit rings.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel.Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Atlantic A0 and B0 specific functions.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for code specific to the Atlantic NIC.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definitions of functions that interface directly with the hardware.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel.Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to support the transmit and receive ring buffers.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add files containing the functions and definitions used in common in
different functional areas.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patches to create the make and configuration files.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 51b7b1c34e (KSZ8851-SNL: Add ethtool support for
EEPROM via eeprom_93cx6, 2011-11-21) this structure member is
unused. Delete it.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is intended for code reuse of mlx5e_modify_rx_cqe_compression
function.
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reduce memory consumption on kdump kernel by decreasing the number of
channels to 1 and the size of RQs and SQs to the minimal values.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
So we can use that from the IB driver too in downstream patches.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add support for SRIOV VF min rate guarantee by using the TSAR BW share
weights mechanism.
The TSAR BW share vport attribute represents the weight of that vport
among the other vports weights which means that the actual vport BW
percentage is the same vport weight percentage among the total vports
weights sum.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The E-Switch FDB size was hard coded to 8k. Change it to be
min(max eswitch table size, max flow counters * num flow groups)
where the max values are read from the firmware and the number of
flow groups is hard-coded as before this change.
We don't know upfront the division of flows to group. This setup allows
each group to be of size up to the where we want to support (we mandate
pairing of flows with counters for offloading). Thus, we don't expect
multiple occurences for a group which in turn adds steering hops.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Tested-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the missing parts for offloading IPv6 tunnels. This includes
route and neigh lookups and construnction of the IPv6 tunnel headers.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use more fields out of the tunnel key (e.g the tunnel source IP address)
provided by upper layers for the route lookup done on the encap offload path.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently we use subset of the input tunnel key fields (id, ip daddr,
dst port) which are provided by upper layers to indentify flows that should
go through the same encapsulation and maintain the HW encapsulation table.
This is redundant and can get us wrong.
Instead, keep a copy of the ip tunnel info provided by the user
through TC and have the tunnel key part as the key to our internal hash.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Move around some settings of variables as pre-step to make things
more robust and clear for the ipv6 case in down-stream patch.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Enhance the parsing of offloaded TC rules to set HW matching on outer
IPv6 encapsulation headers. This effectively adds support for TC tunnel
key release action (decapsulation) of SRIOV offloads over IPv6 tunnels.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current code is allocating the max encap size supported by
the firmware and not the size requested by the caller, fix that.
Also, spare a warning when the size of the encapsulation headers
is bigger from what is supported by the firmware.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the MPSC register, add the functions that configure port-based
packet sampling in hardware and the necessary datatypes in the
mlxsw_sp_port struct. In addition, add the necessary trap for sampled
packets and integrate with matchall offloading to allow offloading of the
sample tc action.
The current offload support is for the tc command:
tc filter add dev <DEV> parent ffff: \
matchall skip_sw \
action sample rate <RATE> group <GROUP> [trunc <SIZE>]
Where only ingress qdiscs are supported, and only a combination of
matchall classifier and sample action will lead to activating hardware
packet sampling.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPSC register allows to configure ingress packet sampling on specific
port of the mlxsw device. The sampled packets are then trapped via
PKT_SAMPLE trap.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw_sp_nexthop_group_mac_update() is called in one of two cases:
1) When the MAC of a nexthop needs to be updated
2) When the size of a nexthop group has changed
In the second case the adjacency entries for the nexthop group need to
be reallocated from the adjacency table. In this case we must write to
the entries the MAC addresses of all the nexthops that should be
offloaded and not only those whose MAC changed. Otherwise, these entries
would be filled with garbage data, resulting in packet loss.
Fixes: a7ff87acd9 ("mlxsw: spectrum_router: Implement next-hop routing")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch we were using a hardcoded RGMII TX clock delay of
2ns (= 1/4 cycle of the 125MHz RGMII TX clock). This value works for
many boards, but unfortunately not for all (due to the way the actual
circuit is designed, sometimes because the TX delay is enabled in the
PHY, etc.). Making the TX delay on the MAC side configurable allows us
to support all possible hardware combinations.
This allows fixing a compatibility issue on some boards, where the
RTL8211F PHY is configured to generate the TX delay. We can now turn
off the TX delay in the MAC, because otherwise we would be applying the
delay twice (which results in non-working TX traffic).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare net_device_ops structure as const as it is only stored in
the netdev_ops field of a net_device structure. This field is of type
const, so net_device_ops structures having same properties can be made
const too.
Done using Coccinelle:
@r1 disable optional_qualifier@
identifier i;
position p;
@@
static struct net_device_ops i@p={...};
@ok1@
identifier r1.i;
position p;
struct net_device ndev;
@@
ndev.netdev_ops=&i@p
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct net_device_ops i;
File size before:
text data bss dec hex filename
6201 744 0 6945 1b21 ethernet/xilinx/xilinx_emaclite.o
File size after:
text data bss dec hex filename
6745 192 0 6937 1b19 ethernet/xilinx/xilinx_emaclite.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare net_device_ops structure as const as it is only stored in
the netdev_ops field of a net_device structure. This field is of type
const, so net_device_ops structures having same properties can be made
const too.
Done using Coccinelle:
@r1 disable optional_qualifier@
identifier i;
position p;
@@
static struct net_device_ops i@p={...};
@ok1@
identifier r1.i;
position p;
struct net_device ndev;
@@
ndev.netdev_ops=&i@p
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct net_device_ops i;
File size before:
text data bss dec hex filename
4821 744 0 5565 15bd ethernet/moxa/moxart_ether.o
File size after:
text data bss dec hex filename
5373 192 0 5565 15bd ethernet/moxa/moxart_ether.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During reset, functions emac_mac_down() and emac_mac_up() are called,
so we don't want to free and claim the IRQ unnecessarily. Move those
operations to open/close.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAC has an internal PHY that is often called the "SGMII". This
SGMII is also connected to an external PHY, which is managed by phylib.
These dual PHYs often cause confusion. In this case, the data structure
for managing the SGMII was mis-named and located in the wrong header file.
Structure emac_phy is renamed to emac_sgmii to clearly indicate it applies
to the internal PHY only. It also also moved from emac_phy.h (which
supports the external PHY) to emac_sgmii.h (where it belongs).
To keep the changes minimal, only the structure name is changed, not
the names of any variables of that type.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4cace675d6 ("bnx2x: Alloc 4k fragment for each rx ring buffer
element") added extra put_page() and get_page() calls on arches where
PAGE_SIZE=4K like x86
Reorder things to avoid this overhead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xgbe_init() routine returns a return code indicating success or
failure, but the return code is not checked. Add code to xgbe_init()
to issue a message when failures are seen and add code to check the
xgbe_init() return code.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A newer version of the hardware is using the same PCI ids for the network
device but has altered register definitions for determining the window
settings for the indirect PCS access. Add support to check for this
hardware and if found use the new register values.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add supporf for the SYSTEMPORT Lite Ethernet controller, this piece of hardware
is largely based on the full-blown SYSTEMPORT and differs in the following:
- no full-blown UniMAC, instead we have the MagicPacket matching from UniMAC at
same offset, and a GMII Interface Block (GIB) for the MAC-level stuff, since
we are always interfaced to an Ethernet switch which is fully Ethernet compliant
shortcuts could be made
- 16 transmit queues, whose interrupts are moved into the first Level-2 interrupt
controller bank
- slight TDMA offset change (a register was inserted after TDMA_STATUS, *sigh*)
- 256 RX descriptors (512 words) and 256 TX descriptors (not visible)
As a consequence of these two things, update the code paths accordingly to
differentiate the full-blown from the light version.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding SYSTEMPORT Lite, which has twice as less transmit
queues than SYSTEMPORT make sure we do allocate TX rings based on the
systemport,txq property to get an appropriate memory footprint.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the LS mask when setting EEE timer.
LS field is 10 bits long and not 11 as currently.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reported-By: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make the code clearer, use rb_entry() instead of container_of() to
deal with rbtree.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes some updates for mlx5 core and mlx5e netdevice driver.
From Leon, a small fix that remove an unnecessary print.
From Eli Cohen, a fix to the FW version printout in case of internal error.
From Eugenia Emantayev, two patches, the 1st adds mlx5 1pps (pulse per
second) mlx5 infrastructure support and the 2nd adds the necessary bits
for mlx5e ptp logic and structures.
From Mohamad, add support for s-tagged packet receive when in promiscuous
mode.
Form Gal Pressman, MCAM (Management capabilities mask register) and PCAM
(Ports capabilities mask register) registers infrastructure, those
registers are needed in order to query the different statistics registers
support in FW, in order for the driver to enable/disable query and
reporting them back to user. On top of this infrastructure we've exposed
new set of statistics groups:
- MPCNT: Physical layer statistical counters (For symbol errors)
- PPCNT: PCIe performance counters
In addition to the statistics capabilities series we've moved the mlx5 HCA
capabilities fields to a dedicated struct under the driver private data.
At the end a small patch to update & query statistics in the most desired
order.
Thanks,
Saeed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYgT2XAAoJEEg/ir3gV/o++x8H/2adUTYToQVH9T9KdeHYcpYj
LtN36/8WFL5MliMpK0DcmuKe9k45ukN5bJGUDhwndJBsHJledBoFw3C6k4vZl0Qw
NiP4t165xmwYQrqI75KVeeGqNWl6LanozZzJVsOM48mSjOXClPnz5BFR4UgL5gTh
q60VmqpSeBjT0EQfT18s1DZCdUY6UUK1XgmgNnFsHUhO/iWVPlNEwItblC2N/YWA
p7lGUAJmAQvDN2sejzz0ElcCieY8yA+cZHgalW0KZK961RCwIl1GECw5xEcLLGxN
O88jaDvTuJpZtl0IOsBi9dwZHx64dx1a+wkFGv+GA6eTgiQ5kPgb2Jdhy26jf9g=
=Hy/5
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-01-19' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 and mlx5e updates 2017-01-19
This series includes some updates for mlx5 core and mlx5e netdevice driver.
From Leon, a small fix that remove an unnecessary print.
From Eli Cohen, a fix to the FW version printout in case of internal error.
From Eugenia Emantayev, two patches, the 1st adds mlx5 1pps (pulse per
second) mlx5 infrastructure support and the 2nd adds the necessary bits
for mlx5e ptp logic and structures.
From Mohamad, add support for s-tagged packet receive when in promiscuous
mode.
Form Gal Pressman, MCAM (Management capabilities mask register) and PCAM
(Ports capabilities mask register) registers infrastructure, those
registers are needed in order to query the different statistics registers
support in FW, in order for the driver to enable/disable query and
reporting them back to user. On top of this infrastructure we've exposed
new set of statistics groups:
- MPCNT: Physical layer statistical counters (For symbol errors)
- PPCNT: PCIe performance counters
In addition to the statistics capabilities series we've moved the mlx5 HCA
capabilities fields to a dedicated struct under the driver private data.
At the end a small patch to update & query statistics in the most desired
order.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver using dev_alloc_page() must not reuse a page allocated from
emergency memory reserve.
Otherwise all packets using this page will be immediately dropped,
unless for very specific sockets having SOCK_MEMALLOC bit set.
This issue might be hard to debug, because only a fraction of received
packets would be dropped.
Fixes: 4415a0319f ("net/mlx5e: Implement RX mapped page cache for page recycle")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adding cpsw_set_ringparam ethtool op, better to carry out
common parts of similar ops splitting descriptors in runtime. It
allows to reuse these parts and shows what the ops actually do.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to duplicate the same function in rx handler to get info
if any interface is running.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to create additional vars to identify if interface is running.
So simplify code by removing redundant var and checking usage counter
instead.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to disable interrupts if no open devices,
they are disabled anyway.
Even no need to disable interrupts if some ndev is opened, In this
case shared resources are not touched, only parameters of ndev shell,
so no reason to disable them also. Removed lines have proved it.
So, no need in redundant check and interrupt disable.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Common res usage is possible only in case an interface is
running. In case of not dual emac here can be only one interface,
so while ndo_open and switch mode, only one interface can be opened,
thus if open is called no any interface is running ... and no common
res are used. So remove check on dual emac, it will simplify
code/understanding and will match the name it's called.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-7 and probably earlier versions get confused by this function
and print a harmless warning:
drivers/net/ethernet/broadcom/bcm63xx_enet.c: In function 'bcm_enet_open':
drivers/net/ethernet/broadcom/bcm63xx_enet.c:1130:3: error: 'phydev' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This adds an initialization for the 'phydev' variable when it is unused
and changes the check to test for that NULL pointer to make it clear
that we always pass a valid pointer here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct qed_ll2_info is rather large, so putting it on the stack
can cause an overflow, as this warning tries to tell us:
drivers/net/ethernet/qlogic/qed/qed_ll2.c: In function 'qed_ll2_start':
drivers/net/ethernet/qlogic/qed/qed_ll2.c:2159:1: error: the frame size of 1056 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
qed_ll2_start_ooo() already uses a dynamic allocation for the structure
to work around that problem, and we could do the same in qed_ll2_start()
as well as qed_roce_ll2_start(), but since the structure is only
used to pass a couple of initialization values here, it seems nicer
to replace it with a different structure.
Lacking any idea for better naming, I'm adding 'struct qed_ll2_conn',
which now contains all the initialization data, and this now simply
gets copied into struct qed_ll2_info rather than assigning all members
one by one.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two new variables are only used inside of an #ifdef and cause
harmless warnings when that is disabled:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c: In function 'init_one':
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4646:9: error: unused variable 'port_vec' [-Werror=unused-variable]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4646:6: error: unused variable 'v' [-Werror=unused-variable]
This adds another #ifdef around the declarations.
Fixes: 96fe11f27b ("cxgb4: Implement ndo_get_phys_port_id for mgmt dev")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 04aeb56a17 ("net/mlx4_en: allocate non 0-order pages for RX
ring with __GFP_NOMEMALLOC") added code that appears to be not needed at
that time, since mlx4 never used __GFP_MEMALLOC allocations anyway.
As using memory reserves is a must in some situations (swap over NFS or
iSCSI), this patch adds this flag.
Note that this driver does not reuse pages (yet) so we do not have to
add anything else.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3e88449344.
With commit 529ed12752 ("net: phy: phy drivers should not set
SUPPORTED_[Asym_]Pause"), phylib now handles automatically enabling
pause frame support in the PHY, and the MAC driver should follow suit.
Since the EMAC driver driver does this, we no longer need to force
pause frames support.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorder update stats flow to update most important counters last,
to get more accurate results.
New update order:
- PCIe counters
- Port counters
- Vport counters
- Queue counters
- Software counters
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Gal Pressman <galp@mellanox.com>
The caps structure consists of hca caps and port/management caps,
all under one roof.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use ethtool -S to query physical layer statistical counters including:
- rx_symbol_errors_phy: Number of symbol errors that were not corrected
by FEC correction algorithm or that FEC was not active on this interface.
- rx_corrected_bits_phy: Number of corrected bits according to active
FEC (RS/FC).
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On load_one, we now cache our capabilities registers internally, similar
to QUERY_HCA_CAP. Capabilities can later be queried using macros
introduced in this patch.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduced registers will expose capabilities of new registers and
features related to port/management.
Driver will query MCAM and PCAM in order to avoid failing on old
firmwares with lack of support.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Today when the driver enter to promiscuous mode or vlan
filter is disabled, we add flow rule to receive any c-taggd
packets, therefore s-tagged packets are dropped.
In order to receive s-tagged packets as well we need to add
flow rule to receive any s-tagged packet.
Fixes: 7cb21b794b ('net/mlx5e: Rename en_flow_table.c to en_fs.c')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch enables the 1PPS IN and 1PPS OUT support according
to the advertised HCA capability. Single pin may be configured
to one of the above mutual exclusive functions via standard
Linux tools and APIs. For example, testptp open source application.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
