HDMI sinks are permitted to de-assert and re-assert the HPD signal to
indicate that their EDID has been updated, which may not involve a
change of video information.
An example of where such a situation can arise is when an AV receiver
is connected between the source and the display device. Events which
can cause the HPD to be deasserted include:
* turning on or switching to standby the AV receiver.
* turning on or switching to standby the display device.
Each of these can change the entire EDID data, or just a part of the
EDID data - it's up to the connected HDMI sink to do what they desire
here. For example
- with the AV receiver and display device both in standby, a source
connected to the AV receiver may provide its own EDID to the source.
- turning on the display device causes the display device's EDID to be
made available in an unmodified form to the source.
- subsequently turning on the AV receiver then provides a modified
version of the display device's EDID.
Moreover, HPD doesn't tell us whether something is actually listening
on the HDMI TDMS signals. The phy gives us a set of RXSENSE indications
which tell us whether there is a sink connected to the TMDS signals.
Currently, we use the HPD signal to enable or disable the HDMI block,
which is questionable when HPD is used in this manner. Using the
RXSENSE would be more appropriate, but there is some bad behaviour
which needs to be coped with. The iMX6 implementation lets the TMDS
signals float when the phy is "powered down", which cause spurious
interrupts. Rather than just using RXSENSE, use RXSENSE and HPD
becoming both active to signal the presence of a device, but loss
of RXSENSE to indicate that the device has been unplugged.
The side effect of this change is that a sink deasserting the HPD
signal to cause a re-read of the EDID data will not cause the bridge
to immediately disable the video signal.
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When connected to HDMI sources, some DVI monitors de-assert their HPD
signal and TDMS loads for one seconds every four seconds when there is
no signal present on the connection.
Unfortunately, this behaviour is indistinguishable from a proper HDMI
setup with an AV receiver in the path to the display: the HDMI spec
requires us to detect HPD deassertions as short as 100ms, which indicate
that the EDID has changed.
Since it is possible to connect a DVI monitor to an AV receiver and then
to a HDMI source, merely working around this by detecting the lack of
HDMI vendor block in the EDID is insufficient - the AV receiver is at
liberty to modify the EDID as it sees fit, and it will place its own
parameters into the EDID including the HDMI vendor block.
DRM has support for forcing the state of a connector, which we should
implement to allow us to work around these broken DVI monitors - we can
tell DRM to force the connection state to indicate that there is always
a device connected to work around this problem. Although this requires
manual configuration, it is better than nothing at all.
When a forced connection state has been set, there is no point handling
our RXSENSE interrupts, so disable them in this circumstance.
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for interlaced video modes to the dw_hdmi bridge. This
mainly involves halving the vertical parameters to be programmed into
the bridge registers, and setting the interlace_allowed connector flag.
This brings working 1080i support. However, 480i and 576i fail to
work due to the lack of proper pixel repetition support, which is not
trivial to add due to the tabular PLL parameterisation. Hence, we
filter out these modes in our mode_valid() method.
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The support for interlaced video modes seems to be broken; we don't use
anything other than the vtotal/htotal from the timing information to
define the various sync counters.
Freescale patches for interlaced video support contain an alternative
sync counter setup, which we include here. This setup produces the
hsync and vsync via the normal counter 2 and 3, but moves the display
enable signal from counter 5 to counter 6. Therefore, we need to
change the display controller setup as well.
The corresponding Freescale patches for this change are:
iMX6-HDMI-support-interlaced-display-mode.patch
IPU-fine-tuning-the-interlace-display-timing-for-CEA.patch
This produces a working interlace format output from the IPU.
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use a function to convert the sync pin to a bit mask for the DI_GENERAL
register, and move this out of the interlace/non-interlace path to the
common path.
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull strscpy string copy function implementation from Chris Metcalf.
Chris sent this during the merge window, but I waffled back and forth on
the pull request, which is why it's going in only now.
The new "strscpy()" function is definitely easier to use and more secure
than either strncpy() or strlcpy(), both of which are horrible nasty
interfaces that have serious and irredeemable problems.
strncpy() has a useless return value, and doesn't NUL-terminate an
overlong result. To make matters worse, it pads a short result with
zeroes, which is a performance disaster if you have big buffers.
strlcpy(), by contrast, is a mis-designed "fix" for strlcpy(), lacking
the insane NUL padding, but having a differently broken return value
which returns the original length of the source string. Which means
that it will read characters past the count from the source buffer, and
you have to trust the source to be properly terminated. It also makes
error handling fragile, since the test for overflow is unnecessarily
subtle.
strscpy() avoids both these problems, guaranteeing the NUL termination
(but not excessive padding) if the destination size wasn't zero, and
making the overflow condition very obvious by returning -E2BIG. It also
doesn't read past the size of the source, and can thus be used for
untrusted source data too.
So why did I waffle about this for so long?
Every time we introduce a new-and-improved interface, people start doing
these interminable series of trivial conversion patches.
And every time that happens, somebody does some silly mistake, and the
conversion patch to the improved interface actually makes things worse.
Because the patch is mindnumbing and trivial, nobody has the attention
span to look at it carefully, and it's usually done over large swatches
of source code which means that not every conversion gets tested.
So I'm pulling the strscpy() support because it *is* a better interface.
But I will refuse to pull mindless conversion patches. Use this in
places where it makes sense, but don't do trivial patches to fix things
that aren't actually known to be broken.
* 'strscpy' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: use global strscpy() rather than private copy
string: provide strscpy()
Make asm/word-at-a-time.h available on all architectures
Two tagged for -stable
One is really a cleanup to match and improve kmemcache interface.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=yqg5
-----END PGP SIGNATURE-----
Merge tag 'md/4.3-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Assorted fixes for md in 4.3-rc.
Two tagged for -stable, and one is really a cleanup to match and
improve kmemcache interface.
* tag 'md/4.3-fixes' of git://neil.brown.name/md:
md/bitmap: don't pass -1 to bitmap_storage_alloc.
md/raid1: Avoid raid1 resync getting stuck
md: drop null test before destroy functions
md: clear CHANGE_PENDING in readonly array
md/raid0: apply base queue limits *before* disk_stack_limits
md/raid5: don't index beyond end of array in need_this_block().
raid5: update analysis state for failed stripe
md: wait for pending superblock updates before switching to read-only
Pull MIPS updates from Ralf Baechle:
"This week's round of MIPS fixes:
- Fix JZ4740 build
- Fix fallback to GFP_DMA
- FP seccomp in case of ENOSYS
- Fix bootmem panic
- A number of FP and CPS fixes
- Wire up new syscalls
- Make sure BPF assembler objects can properly be disassembled
- Fix BPF assembler code for MIPS I"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: scall: Always run the seccomp syscall filters
MIPS: Octeon: Fix kernel panic on startup from memory corruption
MIPS: Fix R2300 FP context switch handling
MIPS: Fix octeon FP context switch handling
MIPS: BPF: Fix load delay slots.
MIPS: BPF: Do all exports of symbols with FEXPORT().
MIPS: Fix the build on jz4740 after removing the custom gpio.h
MIPS: CPS: #ifdef on CONFIG_MIPS_MT_SMP rather than CONFIG_MIPS_MT
MIPS: CPS: Don't include MT code in non-MT kernels.
MIPS: CPS: Stop dangling delay slot from has_mt.
MIPS: dma-default: Fix 32-bit fall back to GFP_DMA
MIPS: Wire up userfaultfd and membarrier syscalls.
Pull irq fixes from Thomas Gleixner:
"This update contains:
- Fix for a long standing race affecting /proc/irq/NNN
- One line fix for ARM GICV3-ITS counting the wrong data
- Warning silencing in ARM GICV3-ITS. Another GCC trying to be
overly clever issue"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Count additional LPIs for the aliased devices
irqchip/gic-v3-its: Silence warning when its_lpi_alloc_chunks gets inlined
genirq: Fix race in register_irq_proc()
The MIPS syscall handler code used to return -ENOSYS on invalid
syscalls. Whilst this is expected, it caused problems for seccomp
filters because the said filters never had the change to run since
the code returned -ENOSYS before triggering them. This caused
problems on the chromium testsuite for filters looking for invalid
syscalls. This has now changed and the seccomp filters are always
run even if the syscall is invalid. We return -ENOSYS once we
return from the seccomp filters. Moreover, similar codepaths have
been merged in the process which simplifies somewhat the overall
syscall code.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11236/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull x86 fixes from Ingo Molnar:
"Fixes all around the map: W+X kernel mapping fix, WCHAN fixes, two
build failure fixes for corner case configs, x32 header fix and a
speling fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/headers/uapi: Fix __BITS_PER_LONG value for x32 builds
x86/mm: Set NX on gap between __ex_table and rodata
x86/kexec: Fix kexec crash in syscall kexec_file_load()
x86/process: Unify 32bit and 64bit implementations of get_wchan()
x86/process: Add proper bound checks in 64bit get_wchan()
x86, efi, kasan: Fix build failure on !KASAN && KMEMCHECK=y kernels
x86/hyperv: Fix the build in the !CONFIG_KEXEC_CORE case
x86/cpufeatures: Correct spelling of the HWP_NOTIFY flag
Pull EFI fixes from Ingo Molnar:
"Two EFI fixes: one for x86, one for ARM, fixing a boot crash bug that
can trigger under newer EFI firmware"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arm64/efi: Fix boot crash by not padding between EFI_MEMORY_RUNTIME regions
x86/efi: Fix boot crash by mapping EFI memmap entries bottom-up at runtime, instead of top-down
Pull drm fixes from Dave Airlie:
"Bunch of fixes all over the place, all pretty small: amdgpu, i915,
exynos, one qxl and one vmwgfx.
There is also a bunch of mst fixes, I left some cleanups in the series
as I didn't think it was worth splitting up the tested series"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (37 commits)
drm/dp/mst: add some defines for logical/physical ports
drm/dp/mst: drop cancel work sync in the mstb destroy path (v2)
drm/dp/mst: split connector registration into two parts (v2)
drm/dp/mst: update the link_address_sent before sending the link address (v3)
drm/dp/mst: fixup handling hotplug on port removal.
drm/dp/mst: don't pass port into the path builder function
drm/radeon: drop radeon_fb_helper_set_par
drm: handle cursor_set2 in restore_fbdev_mode
drm/exynos: Staticize local function in exynos_drm_gem.c
drm/exynos: fimd: actually disable dp clock
drm/exynos: dp: remove suspend/resume functions
drm/qxl: recreate the primary surface when the bo is not primary
drm/amdgpu: only print meaningful VM faults
drm/amdgpu/cgs: remove import_gpu_mem
drm/i915: Call non-locking version of drm_kms_helper_poll_enable(), v2
drm: Add a non-locking version of drm_kms_helper_poll_enable(), v2
drm/vmwgfx: Fix a command submission hang regression
drm/exynos: remove unused mode_fixup() code
drm/exynos: remove decon_mode_fixup()
drm/exynos: remove fimd_mode_fixup()
...
Pull input layer fixes from Dmitry Torokhov:
"Fixes for two recent regressions (in Synaptics PS/2 and uinput
drivers) and some more driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - fix handling of disabling gesture mode"
Input: psmouse - fix data race in __ps2_command
Input: elan_i2c - add all valid ic type for i2c/smbus
Input: zhenhua - ensure we have BITREVERSE
Input: omap4-keypad - fix memory leak
Input: serio - fix blocking of parport
Input: uinput - fix crash when using ABS events
Input: elan_i2c - expand maximum product_id form 0xFF to 0xFFFF
Input: elan_i2c - add ic type 0x03
Input: elan_i2c - don't require known iap version
Input: imx6ul_tsc - fix controller name
Input: imx6ul_tsc - use the preferred method for kzalloc()
Input: imx6ul_tsc - check for negative return value
Input: imx6ul_tsc - propagate the errors
Input: walkera0701 - fix abs() calculations on 64 bit values
Input: mms114 - remove unneded semicolons
Input: pm8941-pwrkey - remove unneded semicolon
Input: fix typo in MT documentation
Input: cyapa - fix address of Gen3 devices in device tree documentation
This patch fixes one cases where abs() was being used with 64-bit
nanosecond values, where the result may be capped at 32-bits.
This potentially could cause watchdog false negatives on 32-bit
systems, so this patch addresses the issue by using abs64().
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1442279124-7309-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
inadvertently changing a huge pmd page into a pmd table entry.
- Function graph tracer panic fix caused by the return_to_handler code
corrupting the multi-regs function return value (composite types).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AJCF
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Fix for transparent huge page change_protection() logic which was
inadvertently changing a huge pmd page into a pmd table entry.
- Function graph tracer panic fix caused by the return_to_handler code
corrupting the multi-regs function return value (composite types).
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: ftrace: fix function_graph tracer panic
arm64: Fix THP protection change logic
Pull m68k updates from Geert Uytterhoeven:
"Summary:
- Fix for accidental modification of arguments of syscall functions
- Wire up new syscalls
- Update defconfigs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/defconfig: Update defconfigs for v4.3-rc1
m68k: Define asmlinkage_protect
m68k: Wire up membarrier
m68k: Wire up userfaultfd
m68k: Wire up direct socket calls
When configuring the interrupt mapping for a new device, we
iterate over all the possible aliases to account for their
maximum MSI allocation. This was introduced by e8137f4f50
("irqchip: gicv3-its: Iterate over PCI aliases to generate ITS configuration").
Turns out that the code doing that is a bit braindead, and repeatedly
accounts for the same device over and over.
Fix this by counting the actual alias that is passed to us by the
core code.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1443800646-8074-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
More agressive inlining in recent versions of GCC have uncovered
a new set of warnings:
drivers/irqchip/irq-gic-v3-its.c: In function its_msi_prepare:
drivers/irqchip/irq-gic-v3-its.c:1148:26: warning: lpi_base may be used
uninitialized in this function [-Wmaybe-uninitialized]
dev->event_map.lpi_base = lpi_base;
^
drivers/irqchip/irq-gic-v3-its.c:1116:6: note: lpi_base was declared here
int lpi_base;
^
drivers/irqchip/irq-gic-v3-its.c:1149:25: warning: nr_lpis may be used
uninitialized in this function [-Wmaybe-uninitialized]
dev->event_map.nr_lpis = nr_lpis;
^
drivers/irqchip/irq-gic-v3-its.c:1117:6: note: nr_lpis was declared here
int nr_lpis;
^
The warning is fairly benign (there is no code path that could
actually use uninitialized variables), but let's silence it anyway
by zeroing the variables on the error path.
Reported-by: Alex Shi <alex.shi@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1443800646-8074-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This contains fixes spread throughout the drivers
Also fixes one more instance of privatecnt in dmaengine
bunch of pxa_dma fixes for reuse of descriptor issue, residue and
no-requestor
odd fixes in xgene, idma, sun4i and zxdma
at_xdmac fixes for cleaning descriptor and block addr mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wcjo
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.3-rc4' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"This contains fixes spread throughout the drivers, and also fixes one
more instance of privatecnt in dmaengine.
Driver fixes summary:
- bunch of pxa_dma fixes for reuse of descriptor issue, residue and
no-requestor
- odd fixes in xgene, idma, sun4i and zxdma
- at_xdmac fixes for cleaning descriptor and block addr mode"
* tag 'dmaengine-fix-4.3-rc4' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: pxa_dma: fix residue corner case
dmaengine: pxa_dma: fix the no-requestor case
dmaengine: zxdma: Fix off-by-one for testing valid pchan request
dmaengine: at_xdmac: clean used descriptor
dmaengine: at_xdmac: change block increment addressing mode
dmaengine: dw: properly read DWC_PARAMS register
dmaengine: xgene-dma: Fix overwritting DMA tx ring
dmaengine: fix balance of privatecnt
dmaengine: sun4i: fix unsafe list iteration
dmaengine: idma64: improve residue estimation
dmaengine: xgene-dma: fix handling xgene_dma_get_ring_size result
dmaengine: pxa_dma: fix initial list move
Pull block fixes from Jens Axboe:
"Another week, another round of fixes.
These have been brewing for a bit and in various iterations, but I
feel pretty comfortable about the quality of them. They fix real
issues. The pull request is mostly blk-mq related, and the only one
not fixing a real bug, is the tag iterator abstraction from Christoph.
But it's pretty trivial, and we'll need it for another fix soon.
Apart from the blk-mq fixes, there's an NVMe affinity fix from Keith,
and a single fix for xen-blkback from Roger fixing failure to free
requests on disconnect"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: factor out a helper to iterate all tags for a request_queue
blk-mq: fix racy updates of rq->errors
blk-mq: fix deadlock when reading cpu_list
blk-mq: avoid inserting requests before establishing new mapping
blk-mq: fix q->mq_usage_counter access race
blk-mq: Fix use after of free q->mq_map
blk-mq: fix sysfs registration/unregistration race
blk-mq: avoid setting hctx->tags->cpumask before allocation
NVMe: Set affinity after allocating request queues
xen/blkback: free requests on disconnection
This reverts commit e51e38494a: we
actually do want the device to work in extended W mode, as this is the
mode that allows us receiving multiple contact information.
Cc: stable@vger.kernel.org
During development it was found that a number of builds would panic
during the kernel init process, more specifically in 'delayed_fput()'.
The panic showed the kernel trying to access a memory address of
'0xb7fdc00' while traversing the 'delayed_fput_list' structure.
Comparing this memory address to the value of the pointer used on
builds that did not panic confirmed that the pointer on crashing
builds must have been corrupted at some stage earlier in the init
process.
By traversing the list earlier and earlier in the code it was found
that 'plat_mem_setup()' was responsible for corrupting the list.
Specifically the line:
memory = cvmx_bootmem_phy_alloc(mem_alloc_size,
__pa_symbol(&__init_end), -1,
0x100000,
CVMX_BOOTMEM_FLAG_NO_LOCKING);
Which would eventually call:
cvmx_bootmem_phy_set_size(new_ent_addr,
cvmx_bootmem_phy_get_size
(ent_addr) -
(desired_min_addr -
ent_addr));
Where 'new_ent_addr'=0x4800000 (the address of 'delayed_fput_list')
and the second argument (size)=0xb7fdc00 (the address causing the
kernel panic). The job of this part of 'plat_mem_setup()' is to
allocate chunks of memory for the kernel to use. At the start of
each chunk of memory the size of the chunk is written, hence the
value 0xb7fdc00 is written onto memory at 0x4800000, therefore the
kernel panics when it goes back to access 'delayed_fput_list' later
on in the initialisation process.
On builds that were not crashing it was found that the compiler had
placed 'delayed_fput_list' at 0x4800008, meaning it wasn't corrupted
(but something else in memory was overwritten).
As can be seen in the first function call above the code begins to
allocate chunks of memory beginning from the symbol '__init_end'.
The MIPS linker script (vmlinux.lds.S) however defines the .bss
section to begin after '__init_end'. Therefore memory within the
.bss section is allocated to the kernel to use (System.map shows
'delayed_fput_list' and other kernel structures to be in .bss).
To stop the kernel panic (and the .bss section being corrupted)
memory should begin being allocated from the symbol '_end'.
Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: aleksey.makarov@auriga.com
Patchwork: https://patchwork.linux-mips.org/patch/11251/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 1a3d59579b ("MIPS: Tidy up FPU context switching") removed FP
context saving from the asm-written resume function in favour of reusing
existing code to perform the same task. However it only removed the FP
context saving code from the r4k_switch.S implementation of resume.
Remove it from the r2300_switch.S implementation too in order to prevent
attempting to save the FP context twice, which would likely lead to an
exception from the second save because the FPU had already been disabled
by the first save.
This patch has only been build tested, using rbtx49xx_defconfig.
Fixes: 1a3d59579b ("MIPS: Tidy up FPU context switching")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/11167/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Allow users of mmc_of_parse() to succeed when CONFIG_GPIOLIB is unset
- Prevent infinite loop of re-tuning for CRC-errors for CMD19 and CMD21
MMC host:
- pxamci: Fix issues with card detect
- sunxi: Fix clk-delay settings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bo65
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.3-rc3' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.3 rc4:
MMC core:
- Allow users of mmc_of_parse() to succeed when CONFIG_GPIOLIB is
unset
- Prevent infinite loop of re-tuning for CRC-errors for CMD19 and
CMD21
MMC host:
- pxamci: Fix issues with card detect
- sunxi: Fix clk-delay settings"
* tag 'mmc-v4.3-rc3' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: core: fix dead loop of mmc_retune
mmc: pxamci: fix card detect with slot-gpio API
mmc: sunxi: Fix clk-delay settings
mmc: core: Don't return an error for CD/WP GPIOs when GPIOLIB is unset
Pull IOVA fixes from David Woodhouse:
"The main fix here is the first one, fixing the over-allocation of
size-aligned requests. The other patches simply make the existing
IOVA code available to users other than the Intel VT-d driver, with no
functional change.
I concede the latter really *should* have been submitted during the
merge window, but since it's basically risk-free and people are
waiting to build on top of it and it's my fault I didn't get it in, I
(and they) would be grateful if you'd take it"
* git://git.infradead.org/intel-iommu:
iommu: Make the iova library a module
iommu: iova: Export symbols
iommu: iova: Move iova cache management to the iova library
iommu/iova: Avoid over-allocating when size-aligned
The entire bpf_jit_asm.S is written in noreorder mode because "we know
better" according to a comment. This also prevented the assembler from
throwing in the required NOPs for MIPS I processors which have no
load-use interlock, thus the load's consumer might end up using the
old value of the register from prior to the load.
Fixed by putting the assembler in reorder mode for just the affected
load instructions. This is not enough for gas to actually try to be
clever by looking at the next instruction and inserting a nop only
when needed but as the comment said "we know better", so getting gas
to unconditionally emit a NOP is just right in this case and prevents
adding further ifdefery.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On x32, gcc predefines __x86_64__ but long is only 32-bit. Use
__ILP32__ to distinguish x32.
Fixes this compiler error in perf:
tools/include/asm-generic/bitops/__ffs.h: In function '__ffs':
tools/include/asm-generic/bitops/__ffs.h:19:8: error: right shift count >= width of type [-Werror=shift-count-overflow]
word >>= 32;
^
This isn't sufficient to build perf for x32, though.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/1443660043.2730.15.camel@decadent.org.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Passing -1 to bitmap_storage_alloc() causes page->index to be set to
-1, which is quite problematic.
So only pass ->cluster_slot if mddev_is_clustered().
Fixes: b97e92574c ("Use separate bitmaps for each nodes in the cluster")
Cc: stable@vger.kernel.org (v4.1+)
Signed-off-by: NeilBrown <neilb@suse.com>
close_sync() needs to set conf->next_resync to a large, but safe value
below MaxSector and use it to determine whether or not to set
start_next_window in wait_barrier()
Solution suggested by Neil Brown.
Reported-by: Nate Dailey <nate.dailey@stratus.com>
Tested-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Remove unneeded NULL test.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ expression x; @@
-if (x != NULL)
\(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NeilBrown <neilb@suse.com>
If faulty disks of an array are more than allowed degraded number, the
array enters error handling. It will be marked as read-only with
MD_CHANGE_PENDING/RECOVERY_NEEDED set. But currently recovery doesn't
clear CHANGE_PENDING bit for read-only array. If MD_CHANGE_PENDING is
set for a raid5 array, all returned IO will be hold on a list till the
bit is clear. But recovery nevery clears this bit, the IO is always in
pending state and nevery finish. This has bad effects like upper layer
can't get an IO error and the array can't be stopped.
Fixes: c3cce6cda1 ("md/raid5: ensure device failure recorded before write request returns.")
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Calling e.g. blk_queue_max_hw_sectors() after calls to
disk_stack_limits() discards the settings determined by
disk_stack_limits().
So we need to make those calls first.
Fixes: 199dc6ed51 ("md/raid0: update queue parameter in a safer location.")
Cc: stable@vger.kernel.org (v2.6.35+ - please apply with 199dc6ed51).
Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
When need_this_block probably shouldn't be called when there
are more than 2 failed devices, we really don't want it to try
indexing beyond the end of the failed_num[] of fdev[] arrays.
So limit the loops to at most 2 iterations.
Reported-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.de>
handle_failed_stripe() makes the stripe fail, eg, all IO will return
with a failure, but it doesn't update stripe_head_state. Later
handle_stripe() has special handling for raid6 for handle_stripe_fill().
That check before handle_stripe_fill() doesn't skip the failed stripe
and we get a kernel crash in need_this_block. This patch clear the
analysis state to make sure no functions wrongly called after
handle_failed_stripe()
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.com>
If a superblock update is pending, wait for it to complete before
letting md_set_readonly() switch to readonly.
Otherwise we might lose important information about a device having
failed.
For external arrays, waiting for superblock updates can wait on
user-space, so in that case, just return an error.
Reported-and-tested-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Unused space between the end of __ex_table and the start of
rodata can be left W+x in the kernel page tables. Extend the
setting of the NX bit to cover this gap by starting from
text_end rather than rodata_start.
Before:
---[ High Kernel Mapping ]---
0xffffffff80000000-0xffffffff81000000 16M pmd
0xffffffff81000000-0xffffffff81600000 6M ro PSE GLB x pmd
0xffffffff81600000-0xffffffff81754000 1360K ro GLB x pte
0xffffffff81754000-0xffffffff81800000 688K RW GLB x pte
0xffffffff81800000-0xffffffff81a00000 2M ro PSE GLB NX pmd
0xffffffff81a00000-0xffffffff81b3b000 1260K ro GLB NX pte
0xffffffff81b3b000-0xffffffff82000000 4884K RW GLB NX pte
0xffffffff82000000-0xffffffff82200000 2M RW PSE GLB NX pmd
0xffffffff82200000-0xffffffffa0000000 478M pmd
After:
---[ High Kernel Mapping ]---
0xffffffff80000000-0xffffffff81000000 16M pmd
0xffffffff81000000-0xffffffff81600000 6M ro PSE GLB x pmd
0xffffffff81600000-0xffffffff81754000 1360K ro GLB x pte
0xffffffff81754000-0xffffffff81800000 688K RW GLB NX pte
0xffffffff81800000-0xffffffff81a00000 2M ro PSE GLB NX pmd
0xffffffff81a00000-0xffffffff81b3b000 1260K ro GLB NX pte
0xffffffff81b3b000-0xffffffff82000000 4884K RW GLB NX pte
0xffffffff82000000-0xffffffff82200000 2M RW PSE GLB NX pmd
0xffffffff82200000-0xffffffffa0000000 478M pmd
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: <stable@vger.kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/1443704662-3138-1-git-send-email-sds@tycho.nsa.gov
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The original bug is a page fault crash that sometimes happens
on big machines when preparing ELF headers:
BUG: unable to handle kernel paging request at ffffc90613fc9000
IP: [<ffffffff8103d645>] prepare_elf64_ram_headers_callback+0x165/0x260
The bug is caused by us under-counting the number of memory ranges
and subsequently not allocating enough ELF header space for them.
The bug is typically masked on smaller systems, because the ELF header
allocation is rounded up to the next page.
This patch modifies the code in fill_up_crash_elf_data() by using
walk_system_ram_res() instead of walk_system_ram_range() to correctly
count the max number of crash memory ranges. That's because the
walk_system_ram_range() filters out small memory regions that
reside in the same page, but walk_system_ram_res() does not.
Here's how I found the bug:
After tracing prepare_elf64_headers() and prepare_elf64_ram_headers_callback(),
the code uses walk_system_ram_res() to fill-in crash memory regions information
to the program header, so it counts those small memory regions that
reside in a page area.
But, when the kernel was using walk_system_ram_range() in
fill_up_crash_elf_data() to count the number of crash memory regions,
it filters out small regions.
I printed those small memory regions, for example:
kexec: Get nr_ram ranges. vaddr=0xffff880077592258 paddr=0x77592258, sz=0xdc0
Based on the code in walk_system_ram_range(), this memory region
will be filtered out:
pfn = (0x77592258 + 0x1000 - 1) >> 12 = 0x77593
end_pfn = (0x77592258 + 0xfc0 -1 + 1) >> 12 = 0x77593
end_pfn - pfn = 0x77593 - 0x77593 = 0 <=== if (end_pfn > pfn) is FALSE
So, the max_nr_ranges that's counted by the kernel doesn't include
small memory regions - causing us to under-allocate the required space.
That causes the page fault crash that happens in a later code path
when preparing ELF headers.
This bug is not easy to reproduce on small machines that have few
CPUs, because the allocated page aligned ELF buffer has more free
space to cover those small memory regions' PT_LOAD headers.
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: kexec@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/1443531537-29436-1-git-send-email-jlee@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In order to cache the EDID properly for tiled displays, we
need to retrieve it before we register the connector with
userspace, otherwise userspace can call get resources
and try and get the edid before we've even cached it.
This fixes some problems when hotplugging mst monitors,
with X/mutter running. As mutter seems to get 0 modes
for one of the monitors in the tile.
v2: fix warning in radeon
handle tile setting in cached path rather than
get edid path.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Update the state before sending the msg to close it.
v2: reset value if return indicates we haven't send the msg.
v3: just clean the code up.
Pointed out by Adam J Richter on
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91481
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
output ports should always have a connector, unless
in the rare case connector allocation fails in the
driver.
In this case we only need to teardown the pdt,
and free the struct, and there is no need to
send a hotplug msg.
In the case were we add the port to the destroy
list we need to send a hotplug if we destroy
any connectors, so userspace knows to reprobe
stuff.
this patch also handles port->connector allocation
failing which should be a rare event, but makes
the code consistent.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is unnecessary and it makes it easier to see what is needed
from port.
also add blank line to make things nicer.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It was just a wrapper around drm_fb_helper_set_par that
called cursor_set2 in addition. Now that the core handles
this, drop this radeon specific version.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If a driver uses the cursor_set2 crtc callback rather than
cursor_set, use that. This fixes the fbdev helper for drivers
that use cursor_set2.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
