Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch introduces the preliminary support for PMICs X-Powers AXP202
and AXP209. The AXP209 and AXP202 are the PMUs (Power Management Unit)
used by A10, A13 and A20 SoCs and developed by X-Powers, a sister company
of Allwinner.
The core enables support for two subsystems:
- PEK (Power Enable Key)
- Regulators
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we pass syscon device node itself as first parameter to this function
there is no need to parse and find syscon device node. So by allowing
"property" parameter as NULL allow syscon_regmap_lookup_by_phandle to
consider passed argument "np" itself as a syscon device node "syscon_np".
This will help us in avoiding addition of "syscon" property in a device node
which points back to same device node in device tree.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The pm8xxx read/write wrappers are no longer necessary now that
all the sub-device drivers are using the regmap API. Remove it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
During suspend the IRQ should be disabled even if this is not a wakeup
source. This is a proper way of fixing the IRQ handling issue during
resume (IRQ handler fails because I2C bus did not resume yet).
When device is suspended and max14577 interrupt is signaled the irq chip
will try to handle it regardless of wakeup source. Device could be woken
up by different IRQ but still the IRQ handler will try to read the
registers over I2C bus and fail because I2C bus won't be ready yet:
max14577 2-0025: Failed to read IRQ status: -5
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
During suspend the IRQ should be disabled even if this is not a wakeup
source. This is a proper way of fixing the IRQ handling issue during
resume (IRQ handler fails because I2C bus did not resume yet).
When device is suspended and sec-core interrupt is signaled the irq chip
will try to handle it regardless of wakeup source. Device could be woken
up by different IRQ but still the IRQ handler will try to read the
registers over I2C bus and fail because I2C bus won't be ready yet.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The device type was stored in sec_pmic_dev state container twice:
- unsigned long type (initialized from of_device_id or i2c_device_id)
- int device_type (initialized as above or from board files when there
is no DTS)
The 'type' field was never used outside of probe so it can be safely
removed.
Change also the device_type in sec_pmic_dev and sec_platform_data to
unsigned long to avoid any casts.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Make sure that we patch the ACCCTL register as the first thing when the
driver loads, thus configuring I2C fast mode and i2c access for dual access
registers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In certain boards the source for the clk32k clock can be gated. In these
boards the clk32k clock can be provided to the driver and it is going to be
enabled/disabled when it is needed.
If the clk32k clock is not provided the driver will assume that it is always
running.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All boards using twl6040 configures the i2c bus to 400KHz. While twl6040's
defaults to normal mode (100KHz). So far twl6040 has no problem with i2c
communication in this configuration it is safer to select fast i2c mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If for some reason the boot loader enabled the audpwron GPIO we will have
pending IRQs to be handled. This seams to break twl6040 for some reason
leading to non working i2c communication (i2c timeouts). Clearing the INTID
register after we requested the audpwron GPIO (and set it to low) will
ensure that the chip will operate normally in this case as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The supply aliases for the MFD devices were being added using devres but
the device hasn't been added at this point and as such we can't use
devres.
The MFD already has a function that removes devices this patch uses the
non-devres versions of the supply alias functions and adds an unregister
in mfd_remove_devices_fn.
Reported-by: Carlo Caione <carlo@caione.org>
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The valid gpio is GPIO0 ~ GPIO58, so ngpio should be 59.
This patch also renames RDC321X_MAX_GPIO to RDC321X_NUM_GPIO because it
actually means the number of available GPIOs.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The rtc-s5m driver does not support all of S2M and S5M chipsets
supported by main MFD sec-core driver. For such chipsets unsupported by
rtc-s5m, the MFD sec-core driver initialized regmap with default config.
This config in such cases wouldn't work at all.
The main MFD sec-core driver shouldn't initialize regmap for child
drivers which is not used by them and even not valid.
Move the allocation of RTC I2C dummy device and initialization of RTC
regmap from main MFD sec-core driver to the rtc-s5m driver. The rtc-s5m
driver will use proper regmap config for supported devices.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This module has always been GPL licensed. It was just missing the explicit
declaration to avoid tainting the kernel.
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Panther Point PCH GPIO configuration is similar to V5 PCHs.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The isolation control register is required when DCVDD is externally
supplied add this in as a readable register.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
After request_threaded_irq() is called there is a chance that an interrupt
may occur before the 'mc13xxx->lock' is initialized, which will trigger a kernel
oops.
In order to prevent that, move the initialization of 'mc13xxx->lock' prior to
requesting the interrupts.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On systems with CONFIG_FRAME_WARN=1024, compiler warns the allocation of
an object of struct device on stack. Make the allocation dynamically to
fix the warning. Also change the caller's return type to int so as to
account for error handling.
drivers/mfd/abx500-core.c: In function ‘abx500_dump_all_banks’:
drivers/mfd/abx500-core.c:167:1: warning: the frame size of 1032 bytes
is larger than 1024 bytes [-Wframe-larger-than=]
Signed-off-by: Aurabindo J <mail@aurabindo.in>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds attributes to the Kontron PLD driver to allow
applications to retrieve firmware information.
Additionally the format has been changed to conform with the
representation in other Kontron software.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add missing mfd_remove_devices() call in remove function.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are two different variants of the tps658640 with slightly
different feature sets.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KGD4
-----END PGP SIGNATURE-----
Merge tag 'regulator-tps658640' into ib-from-regulator-3.16
regulator: Support newer revisions of tps658640
There are two different variants of the tps658640 with slightly
different feature sets.
The TPS658640 has a different set of output voltage for most LDO and
the RTC LDO isn't settable. This chip also report 2 different version
ID, as the datasheet doesn't list the possible values the second ID
has simply been named TPS658640v2.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The only platform using the STMPE expander now boots from
device tree using all-dynamic GPIO and IRQ number assignments, so
remove the mechanism to pass this from the device tree entirely.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The STMPE has VCC and VIO supply lines, and sometimes (as on
Ux500) this comes from a software-controlled regulator. Make
it possible to supply the STMPE with power from these
regulators.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current STMPE I2C probing code does not really match the
compatible strings - it matches node names happening to give
the right device name. Instead, let's introduce some real
compatible matching, more complex, more accurate. Make the
driver depend on OF since all platforms using it are DT-only.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The STMPE driver would just read/modify/write the system control
register on the STMPE1601, meaning it would not properly mask off
the PWM block, which remained active if it was on at boot time.
This makes sure the blocks are always masked off if they were
active on boot, saving some power. Also rename the inconsistenty
named STMPE1601 define for the PWM block activation.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit c42deffd5b.
commit <mmc: rtsx: add support for pre_req and post_req> did use
mutex_unlock() in tasklet, but mutex_unlock() can't be used in
tasklet(atomic context). The driver needs to use mutex to avoid
concurrency, so we can't use tasklet here, the patch need to be
removed.
The spinlock host->lock and pcr->lock may deadlock, one way to solve
the deadlock is remove host->lock in sd_isr_done_transfer(), but if
using workqueue the we can avoid using the spinlock and also avoid
the problem.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds devicetree support for mc13783-codec.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The cpufreq core now supports the cpufreq_for_each_entry macro helper
for iteration over the cpufreq_frequency_table, so use it.
It should have no functional changes.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Explain why there is no need to have a symmetric LED turn-on in resume handler
while calling rtsx_usb_turn_off_led() in suspend handler.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix two possible race condition generated by misuse of del_timer in
rtsx_usb_bulk_transfer_sglist() and uninitialized timers before mfd_add_devices
in rtsx_usb_probe().
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
I noticed a regression where the omap sys_clkreq signal will never
trigger for omap3 when booted with device tree while it triggers
when booted in legacy mode. This means voltage scaling does not
do anything when booted with device tree.
Turns out the reason is we fail to initialize the SmartReflex
enable bit in twl4030 with the following error:
twl: not initialized
And that happens because we are wrongly tinkering with the twl4030
registers in arch/arm/mach-omap2/omap_twl.c before the driver is
initialized. Looking at the the SmartReflex bit enable code in
omap_twl.c, we need to always set it.
So let's fix the issue by always enabling the twl4030 SmartReflex
bit in the drivers/mfd/twl-core.c probe, and drop the related
code in omap_twl.c.
Note that we still have some twl4030 tinkering left in omap_twl.c
for the twl6030 case, but that's a different patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for MAX77836 chipset to the max14577 extcon driver. The
MAX77836 MUIC has additional interrupts (VIDRM, ADC1K) so IRQ handling
is split up into two functions: max14577_parse_irq() and
max77836_parse_irq().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add Maxim 77836 support to max14577 driver. The chipsets have same MUIC
component so the extcon, charger and regulators are almost the same. The
MAX77836 however has also PMIC and Fuel Gauge.
The MAX77836 uses three I2C slave addresses and has additional interrupts
(related to PMIC and Fuel Gauge). It has also Interrupt Source register,
just like MAX77686 and MAX77693.
The MAX77836 PMIC's TOPSYS and INTSRC interrupts are reported in the
PMIC block. The PMIC block has different I2C slave address and uses own
regmap so another regmap_irq_chip is needed.
Since we have two regmap_irq_chip, use shared interrupts on MAX77836.
This patch adds additional defines and functions to the max14577 MFD core
driver so the driver will handle both chipsets. Also this patch replaces
"0x1 << N" with BIT(N) in defines for register masks.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch prepares for adding support for MAX77836 device to existing
max14577 driver by adding MAX14577 prefix to defines of interrupts.
This is only a rename-like patch, new code is not added.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch continues the preparation for adding support for MAX77836
device to existing max14577 driver.
Add enum for types of devices supported by this driver. The device type
will be detected by matching of_device_id, or i2c_device_id as a
fallback.
The patch also moves to separate function the code related to displaying
DeviceID register values.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add muic prefix to regmap config to differentiate between another regmap
config for MAX77836 PMIC node. Additionally remove unused
symbols: MAX14577_REG_INVALID and max14577_irq_source.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Nearly all of the registers in tps65090 combine control bits and
status bits. Turn off caching of all registers except the select few
that can be cached.
In order to avoid adding more duplicate #defines, we also move some
register offset definitions to the mfd driver (and resolve
inconsistent names).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we weren't given an interrupt we shouldn't tell child devices (like
the tps65090 charger) that they have an interrupt. This is needed so
that we can support polling mode in the tps65090 charger driver.
See also (charger: tps65090: Allow charger module to be used when no
irq).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is more idiomatic to process things relating to the regulator in its
driver. This patch moves both processing of device tree relating to the
regulator and checking if the regulator is external from arizona-core
into the regulator driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch factors out the reading of GPIOs for the Arizona devices
into a helper function.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior.
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V.
- Add GPIO descriptor based slot-gpio card detect API.
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c.
- mmci: Support HW busy detection on ux500.
- omap: Support MMC_ERASE.
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23.
- rtsx: Support pre-req/post-req async.
- sdhci: Add support for Realtek RTS5250 controllers.
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect.
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support.
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6S8w
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.15:
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
- Add GPIO descriptor based slot-gpio card detect API
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
- mmci: Support HW busy detection on ux500
- omap: Support MMC_ERASE
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
- rtsx: Support pre-req/post-req async
- sdhci: Add support for Realtek RTS5250 controllers
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"
* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
mmc: sdhci-acpi: Intel SDIO has broken card detect
mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
mmc: sdhci-msm: Add platform_execute_tuning implementation
mmc: sdhci-msm: Initial support for Qualcomm chipsets
mmc: sdhci-msm: Qualcomm SDHCI binding documentation
sdhci: only reprogram retuning timer when flag is set
mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
mmc: sdhci: Allow for irq being shared
mmc: sdhci-acpi: Add device id 80860F16
mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
mmc: slot-gpio: Split out CD IRQ request into a separate function
mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
mmc: sdhci-spear: use generic card detection gpio support
mmc: sdhci-spear: remove support for power gpio
mmc: sdhci-spear: simplify resource handling
mmc: sdhci-spear: fix platform_data usage
mmc: sdhci-spear: fix error handling paths for DT
mmc: sdhci-bcm-kona: fix build errors when built-in
...
A large part of the arm-soc patches are nowadays DT changes, adding support
for new SoCs, boards and devices without changing kernel source. The plan
is still to move the devicetree files out of the kernel tree and reduce
the amount of churn going on here, but we keep finding reasons to delay
doing that.
Changes are really all over the place, with little sticking out particularly.
We have contributions from a total of 116 people in this branch.
Unfortunately, the size of this branch also causes a significant number
of conflicts at the moment, typically when subsystem maintainers merge
patches that change the driver at the same time as the dts files. In
most cases this could be avoided because the dts changes are supposed
to be compatible in both ways, and we are asking everyone to send ARM
dts changes through our tree only.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=zl/N
-----END PGP SIGNATURE-----
Merge tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"A large part of the arm-soc patches are nowadays DT changes, adding
support for new SoCs, boards and devices without changing kernel
source. The plan is still to move the devicetree files out of the
kernel tree and reduce the amount of churn going on here, but we keep
finding reasons to delay doing that.
Changes are really all over the place, with little sticking out
particularly. We have contributions from a total of 116 people in
this branch.
Unfortunately, the size of this branch also causes a significant
number of conflicts at the moment, typically when subsystem
maintainers merge patches that change the driver at the same time as
the dts files. In most cases this could be avoided because the dts
changes are supposed to be compatible in both ways, and we are asking
everyone to send ARM dts changes through our tree only"
* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
dts: stmmac: Document the clocks property in the stmmac base document
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
ARM: STi: stih416: Add support for the FSM Serial Flash Controller
ARM: tegra: fix Dalmore pinctrl configuration
ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
ARM: dts: Build all keystone dt blobs
ARM: dts: keystone: Fix control register range for clktsip
ARM: dts: keystone: Fix domain register range for clkfftc1
ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
ARM: dts: bcm21664: Add device tree files.
ARM: DT: bcm21664: Device tree bindings
ARM: efm32: properly namespace i2c location property
ARM: efm32: fix unit address part in USART2 device nodes' names
ARM: mvebu: Enable NAND controller in Armada 385-DB
ARM: mvebu: Add support for NAND controller in Armada 38x SoC
ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
...
This release has lots and lots of small cleanups and fixes in the
regulator subsystem, mainly cleaning up some bad patterns that got
duplicated in DT code, but otherwise very little of note outside
of the scope of the relevant drivers:
- Support for configuration of the initial state for gpio regulators
with multi-voltage support.
- Support for calling regulator_set_voltage() on fixed regulators.
- New drivers for Broadcom BCM590xx, Freescale pfuze200, Samsung S2MPA01 &
S2MPS11/4, some PWM controlled regulators found on some ST boards and
TI TPS65218.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mrN5
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This release has lots and lots of small cleanups and fixes in the
regulator subsystem, mainly cleaning up some bad patterns that got
duplicated in DT code, but otherwise very little of note outside of
the scope of the relevant drivers:
- Support for configuration of the initial state for gpio regulators
with multi-voltage support.
- Support for calling regulator_set_voltage() on fixed regulators.
- New drivers for Broadcom BCM590xx, Freescale pfuze200, Samsung
S2MPA01 & S2MPS11/4, some PWM controlled regulators found on some
ST boards and TI TPS65218"
* tag 'regulator-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (154 commits)
regulator: aat2870: Use regulator_map_voltage_ascend
regulator: st-pwm: Convert to get_voltage_sel
regulator: Add new driver for ST's PWM controlled voltage regulators
regulator: bcm590xx: Remove **rdev from struct bcm590xx_reg
regulator: bcm590xx: Make the modalias matches the driver name
regulator: s5m8767: Convert to use regulator_[enable|disable|is_enabled]_regmap
regulator: db8500-prcmu: Set 1.8V as a fixed voltage for vsmps2
regulator: s2mps11: Add missing of_node_put
regulator: s2mps11: Use of_get_child_by_name
Documentation: mfd: s2mps11: Document support for S2MPS14
regulator: s2mps11: Add set_suspend_disable for S2MPS14
regulator: s2mps11: Add support for S2MPS14 regulators
regulator: max8660: Fix brace alignment
regulator: dbx500: use seq_puts() instead of seq_printf()
regulator: dbx500-prcmu: Silence checkpatch warnings
regulator: anatop: Remove checking control_reg in [set|get]_voltage_sel
regulator: max8952: Silence checkpatch warning
regulator: max8925: Silence checkpatch warning
regulator: max8660: Silence checkpatch warnings
regulator: arizona-ldo1: Correct default regulator init_data
...
The DSPs will often control there own clock speeds whilst running as
such we should mark the registers controlling this as volatile.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
