Impact: cleanup
* Come on, struct info? s/struct info/struct math_emu_info/
* Use struct pt_regs and kernel_vm86_regs instead of defining its own
register frame structure.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: dump the correct %gs into a.out core dump
aout_dump_thread() read %gs but didn't include it in core dump. Fix
it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 6194ba6ff6 ("x86: don't special-case
pmd allocations as much") made changes to the way we handle pmd allocations,
and while doing that it dropped a call to paravirt_release_pd on the
pgd page from the pgd_dtor code path.
As a result of this missing release, the hypervisor is now unaware of the
pgd page being freed, and as a result it ends up tracking this page as a
page table page.
After this the guest may start using the same page for other purposes, and
depending on what use the page is put to, it may result in various performance
and/or functional issues ( hangs, reboots).
Since this release is only required for VMI, I now release the pgd page from
the (vmi)_pgd_free hook.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Impact: find right nr_irqs_gsi on some systems.
One test-system has gap between gsi's:
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 0, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: IOAPIC (id[0x05] address[0xfeafd000] gsi_base[48])
[ 0.000000] IOAPIC[1]: apic_id 5, version 0, address 0xfeafd000, GSI 48-54
[ 0.000000] ACPI: IOAPIC (id[0x06] address[0xfeafc000] gsi_base[56])
[ 0.000000] IOAPIC[2]: apic_id 6, version 0, address 0xfeafc000, GSI 56-62
...
[ 0.000000] nr_irqs_gsi: 38
So nr_irqs_gsi is not right. some irq for MSI will overwrite with io_apic.
need to get that with acpi_probe_gsi when acpi io_apic is used
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For Intel 7400 series CPUs, the recommendation is to use a clflush on the
monitored address just before monitor and mwait pair [1].
This clflush makes sure that there are no false wakeups from mwait when the
monitored address was recently written to.
[1] "MONITOR/MWAIT Recommendations for Intel Xeon Processor 7400 series"
section in specification update document of 7400 series
http://download.intel.com/design/xeon/specupdt/32033601.pdf
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Due to recurring issues with DMAR support on certain platforms.
There's a number of filesystem corruption incidents reported:
https://bugzilla.redhat.com/show_bug.cgi?id=479996http://bugzilla.kernel.org/show_bug.cgi?id=12578
Provide a Kconfig option to change whether it is enabled by
default.
If disabled, it can still be reenabled by passing intel_iommu=on to the
kernel. Keep the .config option off by default.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On an x86 system which doesn't support global mappings,
__supported_pte_mask has _PAGE_GLOBAL clear, to make sure it never
appears in the PTE. pfn_pte() and so on will enforce it with:
static inline pte_t pfn_pte(unsigned long page_nr, pgprot_t pgprot)
{
return __pte((((phys_addr_t)page_nr << PAGE_SHIFT) |
pgprot_val(pgprot)) & __supported_pte_mask);
}
However, we overload _PAGE_GLOBAL with _PAGE_PROTNONE on non-present
ptes to distinguish them from swap entries. However, applying
__supported_pte_mask indiscriminately will clear the bit and corrupt the
pte.
I guess the best fix is to only apply __supported_pte_mask to present
ptes. This seems like the right solution to me, as it means we can
completely ignore the issue of overlaps between the present pte bits and
the non-present pte-as-swap entry use of the bits.
__supported_pte_mask contains the set of flags we support on the
current hardware. We also use bits in the pte for things like
logically present ptes with no permissions, and swap entries for
swapped out pages. We should only apply __supported_pte_mask to
present ptes, because otherwise we may destroy other information being
stored in the ptes.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: cleanup
Some lines exceed the 80 char width making them unreadable.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch echoes what we already do on 32-bit since
90f7d25c6b, and prints the DMI
product name in show_regs, so that system specific problems can be
easily identified.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix to enable APIC for AMD Fam10h on chipsets with a missing/b0rked
ACPI MP table (MADT)
Booting a 32bit kernel on an AMD Fam10h CPU running on chipsets with
missing/b0rked MP table leads to a hang pretty early in the boot process
due to the APIC not being initialized. Fix that by falling back to the
default APIC base address in 32bit code, as it is done in the 64bit
codepath.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: Fix race condition
xen_mc_batch has a small preempt race where it takes the address of a
percpu variable immediately before disabling interrupts, thereby
leaving a small window in which we may migrate to another cpu and save
the flags in the wrong percpu variable. Disable interrupts before
saving the old flags in a percpu.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: Documentation only
There is an email alias as well to reach the x86 maintainers: x86@kernel.org.
Document it.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: Fixes dumpstack and KDB on 64 bits
This re-adds the old stack pointer to the top of the irqstack to help
with unwinding. It was removed in commit d99015b1ab
as part of the save_args out-of-line work.
Both dumpstack and KDB require this information.
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: Change link order of pciehp & acpiphp
PCI hotplug: fakephp: Allocate PCI resources before adding the device
PCI MSI: Fix undefined shift by 32
PCI PM: Do not wait for buses in B2 or B3 during resume
PCI PM: Power up devices before restoring their state
PCI PM: Fix hibernation breakage on EeePC 701
PCI: irq and pci_ids patch for Intel Tigerpoint DeviceIDs
PCI PM: Fix suspend error paths and testing facility breakage
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
slub: fix per cpu kmem_cache_cpu array memory leak
kmalloc: return NULL instead of link failure
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
fbdev/atyfb: Fix DSP config on some PowerMacs & PowerBooks
powerpc: Fix oops on some machines due to incorrect pr_debug()
powerpc/ps3: Printing fixups for l64 to ll64 convserion drivers/net
powerpc/5200: update device tree binding documentation
powerpc/5200: Bugfix for PCI mapping of memory and IMMR
powerpc/5200: update defconfigs
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched_rt: don't use first_cpu on cpumask created with cpumask_and
sched: fix buddie group latency
sched: clear buddies more aggressively
sched: symmetric sync vs avg_overlap
sched: fix sync wakeups
cpuset: fix possible deadlock in async_rebuild_sched_domains
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
pxamci: enable DMA for write ops after CMD/RESP
pxamci: replace #ifdef CONFIG_PXA27x with if (cpu_is_pxa27x())
ricoh_mmc: Use suspend_late/resume_early
mmci: Add support for ST Micro derivate
mmc: Add a MX2/MX3 specific SDHC driver
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
icside: fix PCB version 6 support (v2)
tx4939ide: typo fix and minor cleanup
ide: add CS5536 host driver (v3)
ide: Force VIA IDE legacy interrupts for AmigaOne boards
IDE: Unregister and disable devices if initialization fails.
ide: fix ide_register_port() failure handling
ide: struct device - replace bus_id with dev_name(), dev_set_name()
ide-cd: fix DMA for non bio-backed requests
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb:
uwb: lock rc->rsvs_lock with spin_lock_bh()
wusb: timeout when waiting for ASL/PZL updates in whci-hcd
uwb: remove unused #include <version.h>'s
wusb: return -ENOTCONN when resetting a port with no connected device
uwb: safely remove all reservations
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: add text file detailing queue/ sysfs files
bio.h: If they MUST be inlined, then use __always_inline
Fix misleading comment in bio.h
block: fix inconsistent parenthesisation of QUEUE_FLAG_DEFAULT
block: fix oops in blk_queue_io_stat()
The host really shouldn't be notifying us of config changes
before the device status is VIRTIO_CONFIG_S_DRIVER or
VIRTIO_CONFIG_S_DRIVER_OK.
However, if we do happen to be interrupted while we're not
attached to a driver, we really shouldn't oops. Prevent
this simply by checking that device->driver is non-NULL
before trying to notify the driver of config changes.
Problem observed by doing a "set_link virtio.0 down" with
QEMU before the net driver had been loaded.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current refcounting for modules (done if CONFIG_MODULE_UNLOAD=y) is
using a lot of memory.
Each 'struct module' contains an [NR_CPUS] array of full cache lines.
This patch uses existing infrastructure (percpu_modalloc() &
percpu_modfree()) to allocate percpu space for the refcount storage.
Instead of wasting NR_CPUS*128 bytes (on i386), we now use
nr_cpu_ids*sizeof(local_t) bytes.
On a typical distro, where NR_CPUS=8, shiping 2000 modules, we reduce
size of module files by about 2 Mbytes. (1Kb per module)
Instead of having all refcounters in the same memory node - with TLB misses
because of vmalloc() - this new implementation permits to have better
NUMA properties, since each CPU will use storage on its preferred node,
thanks to percpu storage.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the PXA270 MMC hardware, there seems to be an issue of
data corruption on writes where a 4KB data block is offset
by one byte.
If we delay enabling the DMA for writes until after the CMD/RESP
has finished, the problem seems to be fixed.
related to PXA270 Erratum #91
Tested-by: Vernon Sauder <VernonInHand@gmail.com>
Signed-off-by: Cliff Brake <cbrake@bec-systems.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
If ricoh_mmc suspends before sdhci_pci, it will pull the card
out from under the controller, which could leave the system in
a very confused state.
Using suspend_late/resume_early ensures that sdhci_pci suspends first
and resumes second.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds support for the ST Microelectronics version of
the PL180 PrimeCell. They use designer ID 0x80 and have a few
alterations/bugfixes related to open drain and HW flow control.
They also add some SDIO registers, I am unsure if these are
in ST HW only or if this is things also added in later ARM
revisions, but they are included in the mmci.h file for
completeness.
Signed-off-by: Linus Walleij <linus.walleij@ericsson.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds a MX2/MX3 specific SDHC driver. The hardware is basically
the same as in the MX1, but unlike the MX1 controller the MX2
controller just works as expected. Since the MX1 driver has more
workarounds for bugs than anything else I had no success with supporting
MX1 and MX2 in a sane way in one driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
We need to pass struct ide_port_info also to ide_host_register().
v2:
Fix v5/v6 mismatch noticed by Russell.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The bcount is greater than 0 and less than or equal to 0x10000.
Thus '(bcount & 0xffff) == 0x0000' can be simplified as 'bcount == 0x10000'.
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is a port of libata's pata_cs5536.c (written by Martin K. Petersen)
to IDE subsystem.
Changes done while at it:
* Reprogram PIO/MWDMA timings if needed before and after DMA transfer
(chipset uses shared PIO/MWDMA timings).
* Fix cable detection to report 80-wires cable if BIOS set it for any
device on a port (IDE core will do drive-side cable detection later).
* Don't disable UDMA while programming PIO timings.
* Simplify PCI/MSR support.
Pros of having IDE host driver in addition to libata's one:
* IDE is much lighter than SCSI+libata, the host driver itself is also
a bit smaller:
text data bss dec hex filename
1261 496 4 1761 6e1 drivers/ata/pata_cs5536.o
1242 128 4 1374 55e drivers/ide/cs5536.o
* This allows use of IDE features which are unavailable under libata.
v2:
* Fixes per review from Sergei:
- simplify dependency check in Kconfig
- use IDE_DRV_MASK also for ->drive_data
- disable UDMA when programming MWDMA
- program new DTC timings only when necessary
- fix printk() level in cs5536_init_one()
* Fix patch description according to comments from Alan and Sergei.
v3:
* Smarter masking of UDMA bits per Sergei's suggestion.
Cc: Martin K. Petersen <mkp@mkp.net>
Cc: Karl Auerbach <karl@iwl.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The AmigaOne uses the onboard VIA IDE controller in legacy mode (like the
Pegasos).
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Cc: "Grant Likely" <grant.likely@secretlab.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On reboot the loop in device_shutdown gets confused by these partially
initialized devices and goes into an infinite loop. Therefore unregister
and disable these devices.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
[bart: remove leftover hwif->present clearing + update patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out port freeing from ide_host_free() to ide_free_port().
* Add ide_disable_port() and use it on ide_register_port() failure.
Cc: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
bvec_kmap_irq() and bvec_kunmap_irq() comments say they MUST be inlined,
so mark them as __always_inline.
Signed-off-by: Alberto Bertogli <albertito@blitiri.com.ar>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The comment says "remember to add offset!", but the function already adds
it.
Signed-off-by: Alberto Bertogli <albertito@blitiri.com.ar>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Some initial probe requests don't have disk->queue mapped yet, so we
can't rely on a non-NULL queue in blk_queue_io_stat(). Wrap it in
blk_do_io_stat().
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Since the complete re-write in 2.6.10, some PowerMacs (At least PowerMac 5500
and PowerMac G3 Beige rev A) with ATI Mach64 chip have suffered from unstable
columns in their framebuffer image. This seems to depend on a value (4) read
from PLL_EXT_CNTL register, which leads to incorrect DSP config parameters to
be written to the chip. This patch uses a value calculated by aty_init_pll_ct
instead, as a starting point.
There are questions as to whether this should be extended to other platforms
or maybe made dependent on specific chip types, but in the meantime, this has
been tested on various powermacs and works for them so let's commit it.
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Tested-by: Michael Pettersson <mike@it.uu.se>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recently, a patch left DEBUG enabled in the powerpc common PCI code,
resulting in an old bug in a pr_debug() statement to show up and cause
a NULL dereference on some machines.
This fixes the pr_debug() statement and reverts to DEBUG not being
force-enabled in that file.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This essentially reverts commit 8edb08caf6.
It downgraded our mmap semaphore to a read-lock while mlocking pages, in
order to allow other threads (and external accesses like "ps" et al) to
walk the vma lists and take page faults etc. Which is a nice idea, but
the implementation does not work.
Because we cannot upgrade the lock back to a write lock without
releasing the mmap semaphore, the code had to release the lock entirely
and then re-take it as a writelock. However, that meant that the caller
possibly lost the vma chain that it was following, since now another
thread could come in and mmap/munmap the range.
The code tried to work around that by just looking up the vma again and
erroring out if that happened, but quite frankly, that was just a buggy
hack that doesn't actually protect against anything (the other thread
could just have replaced the vma with another one instead of totally
unmapping it).
The only way to downgrade to a read map _reliably_ is to do it at the
end, which is likely the right thing to do: do all the 'vma' operations
with the write-lock held, then downgrade to a read after completing them
all, and then do the "populate the newly mlocked regions" while holding
just the read lock. And then just drop the read-lock and return to user
space.
The (perhaps somewhat simpler) alternative is to just make all the
callers of mlock_vma_pages_range() know that the mmap lock got dropped,
and just re-grab the mmap semaphore if it needs to mlock more than one
vma region.
So we can do this "downgrade mmap sem while populating mlocked regions"
thing right, but the way it was done here was absolutely not correct.
Thus the revert, in the expectation that we will do it all correctly
some day.
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
