According to errata i880 description the speed of Ethernet port 1 on AM572x
SoCs rev 1.1 should be limited to 10/100Mbps, because RGMII2 Switching
Characteristics are not compatible with 1000 Mbps operation [1].
The issue is fixed with Rev 2.0 silicon.
Hence, rework Beagle-X15 and Begale-X15-revb1 to use phy-handle instead of
phy_id and apply corresponding limitation to the Ethernet Phy 1.
[1] http://www.ti.com/lit/er/sprz429j/sprz429j.pdf
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Latest update to the BeagleBoard-X15 platform (revision B1)[1] updates
for allowing UHS SD cards to function with the split of supply to SD
card from a dedicated LDO.
As a result of this, AM57xx BeagleBoard-X15 now uses gpio2_30 instead
of gpio6_28 for HDMI because HDMI_LS_OE should now be switched from
GPIO6_28(Y9) to GPIO2_30 (AG8) to avoid a 1.8V GPIO toggling a 3.3V
SoC input when the SD card is in UHS 1.8V mode.
NOTE: For UHS mode to function, we need full fledged IODelay support
in kernel to be functional. IODelay support is yet to be added.
Further, It does not make much sense to spin off a new board
compatible flag since there is no real functional benefit for the
same.
Note: Even though production version is supposed to be B1, there is
over ~200 boards of previous version (A2)[2] out there which continue
to get supported with the existing dts file (to maintain compatibility
with existing bootloaders for A2) and the production board is now
supported as revb1.
[1] https://github.com/beagleboard/beagleboard-x15/blob/master/BEAGLEBOARD_X15_REV_B1.pdf
[2] http://marc.info/?l=linux-arm-kernel&m=147273929820708&w=2
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pinmuxing for DRA7x/AM57x family of processors need to be done in IO
isolation as part of initial bootloader executed from SRAM. This is
done as part of iodelay configuration sequence and is required due
to the limitations introduced by erratum ID: i869[1] (IO Glitches
can occur when changing IO settings) and elaborated in the Technical
Reference Manual[2] 18.4.6.1.7 Isolation Requirements.
Only peripheral that is permitted for dynamic pin mux configuration
is MMC and DCAN. MMC is permitted to change to accommodate the
requirements for varied speeds (which require IO-delay support in
kernel as well). DCAN is a result of i893[1] (DCAN initialization
sequence). However, since we don't use DCAN on X15, with the exception
of MMC, all other pin mux configurations are removed from the dts.
[1] http://www.ti.com/lit/pdf/sprz429
[2] http://www.ti.com/lit/pdf/sprui30
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /leds/led@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- dts: rename 'ide-disk' to 'disk-activity'
- platform: rename 'ide-disk' to 'disk-activity'
- defconfig: rename 'LEDS_TRIGGER_IDE_DISK' to 'LEDS_TRIGGER_DISK'
Signed-off-by: Stephan Linz <linz@li-pro.net>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
These are all the updates to device tree files for 32-bit platforms,
which as usual makes up the bulk of the ARM SoC changes: 462 non-merge
changesets, 450 files changed, 23340 insertions, 5216 deletions.
The three platforms that are added with the "soc" branch are here as well,
and we add some related machine files:
- For Aspeed AST2400/AST2500, we get the evaluation platform and
the Tyan Palmetto POWER8 mainboard that uses the AST2400 BMC
- For Oxnas 810SE, the Western Digital "My Book World Edition"
is added as the only platform at the moment.
- For ARM MPS2, the AN385 (Cortex-M3) and AN399 (Cortex-M7)
are supported
On the ARM Realview development platform, we now support all machines
with device tree, previously only the board files were supported, which
in turn will likely be removed soon.
Qualcomm IPQ4019 is the second generation ARM based "Internet Processor",
following the IPQ806x that is used in many high-end WiFi routers. This one
integrates two ath10k wifi radios that were previously on separate chips.
Other boards that got added for existing chips are:
- On Ti OMAP family:
- Amazon Kindle Fire, first generation, tablet and ebook reader
- OnRISC Baltos iR 2110 and 3220 embedded industrial PCs
- TI AM5728 IDK, TI AM3359 ICE-V2, and TI DRA722 Rev C EVM
development systems
- On Samsung EXYNOS platform:
- Samsung ARTIK5 evaluation board, see
https://www.artik.io/modules/overview/artik-5/
- On NXP i.MX platforms:
- Ka-Ro electronics TX6S-8034, TX6S-8035, TX6U-8033, TX6U-81xx,
TX6Q-1036, TX6Q-1110/-1130, TXUL-0010 and TXUL-0011 industrial
SoM modules
- Embest MarS Board i.MX6Dual DIY platform
- Boundary Devices i.MX6 Quad Plus Nitrogen6_MAX and
SoloX Nitrogen6sx embedded boards
- Technexion Pico i.MX6UL compute module
- ZII VF610 Development Board
- On Marvell embedded (mvebu, orion, kirkwood) platforms:
- Linksys Viper (E4200v2 / EA4500) WiFi router
- Buffalo Kurobox Pro NAS
- On Qualcomm Snapdragon:
- Arrow DragonBoard 600c (96boards) with APQ8064 Snapdragon 600
- On Rockchips platform:
- mqmaker MiQi single-board computer
- On Altera SoCFPGA:
- samtec VIN|ING 1000 vehicle communication interface
- On Allwinner Sunxi platforms:
- Dserve DSRV9703C tablet
- Difrnce DIT4350 tablet
- Colorfly E708 Q1 tablet
- Polaroid MID2809PXE04 tablet
- Olimex A20 OLinuXino LIME2 single board computer
- Xunlong Orange Pi 2, Orange Pi One, and Orange Pi PC
single board computers
Across many platforms, bug fixes went in to address warnings that
dtc now emits with 'make dtbs W=1'. Further changes for device enablement
went into Ti OMAP, bcm283x (Raspberry Pi), bcm47xx (wifi router),
Ti Davinci, Samsung EXYNOS, Marvell mvebu/kirkwood/orion, NXP i.MX/Vybrid
NXP LPC18xx, NXP LPC32xx, Renesas shmobile/r-mobile/r-car, Rockchips
rk3xxx, ST Ux500, ST STi, Atmel AT91/SAMA5, Altera SoCFPGA, Allwinner
Sunxi, Sigma Designs Tango, NVIDIA Tegra, Socionext Uniphier and ARM
Versatile Express.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Nx46
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"These are all the updates to device tree files for 32-bit platforms,
which as usual makes up the bulk of the ARM SoC changes: 462 non-merge
changesets, 450 files changed, 23340 insertions, 5216 deletions.
The three platforms that are added with the "soc" branch are here as
well, and we add some related machine files:
- For Aspeed AST2400/AST2500, we get the evaluation platform and the
Tyan Palmetto POWER8 mainboard that uses the AST2400 BMC
- For Oxnas 810SE, the Western Digital "My Book World Edition" is
added as the only platform at the moment.
- For ARM MPS2, the AN385 (Cortex-M3) and AN399 (Cortex-M7) are
supported
On the ARM Realview development platform, we now support all machines
with device tree, previously only the board files were supported,
which in turn will likely be removed soon.
Qualcomm IPQ4019 is the second generation ARM based "Internet
Processor", following the IPQ806x that is used in many high-end WiFi
routers. This one integrates two ath10k wifi radios that were
previously on separate chips.
Other boards that got added for existing chips are:
Ti OMAP family:
- Amazon Kindle Fire, first generation, tablet and ebook reader
- OnRISC Baltos iR 2110 and 3220 embedded industrial PCs
- TI AM5728 IDK, TI AM3359 ICE-V2, and TI DRA722 Rev C EVM
development systems
Samsung EXYNOS platform:
- Samsung ARTIK5 evaluation board, see
https://www.artik.io/modules/overview/artik-5/
NXP i.MX platforms:
- Ka-Ro electronics TX6S-8034, TX6S-8035, TX6U-8033, TX6U-81xx,
TX6Q-1036, TX6Q-1110/-1130, TXUL-0010 and TXUL-0011 industrial
SoM modules
- Embest MarS Board i.MX6Dual DIY platform
- Boundary Devices i.MX6 Quad Plus Nitrogen6_MAX and SoloX
Nitrogen6sx embedded boards
- Technexion Pico i.MX6UL compute module
- ZII VF610 Development Board
Marvell embedded (mvebu, orion, kirkwood) platforms:
- Linksys Viper (E4200v2 / EA4500) WiFi router
- Buffalo Kurobox Pro NAS
Qualcomm Snapdragon:
- Arrow DragonBoard 600c (96boards) with APQ8064 Snapdragon 600
Rockchips platform:
- mqmaker MiQi single-board computer
Altera SoCFPGA:
- samtec VIN|ING 1000 vehicle communication interface
Allwinner Sunxi platforms:
- Dserve DSRV9703C tablet
- Difrnce DIT4350 tablet
- Colorfly E708 Q1 tablet
- Polaroid MID2809PXE04 tablet
- Olimex A20 OLinuXino LIME2 single board computer
- Xunlong Orange Pi 2, Orange Pi One, and Orange Pi PC single board
computers
Across many platforms, bug fixes went in to address warnings that dtc
now emits with 'make dtbs W=1'. Further changes for device enablement
went into Ti OMAP, bcm283x (Raspberry Pi), bcm47xx (wifi router), Ti
Davinci, Samsung EXYNOS, Marvell mvebu/kirkwood/orion, NXP i.MX/Vybrid
NXP LPC18xx, NXP LPC32xx, Renesas shmobile/r-mobile/r-car, Rockchips
rk3xxx, ST Ux500, ST STi, Atmel AT91/SAMA5, Altera SoCFPGA, Allwinner
Sunxi, Sigma Designs Tango, NVIDIA Tegra, Socionext Uniphier and ARM
Versatile Express"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (458 commits)
ARM: dts: tango4: Import watchdog node
ARM: dts: tango4: Update cpus node for cpufreq
ARM: dts: tango4: Update DT to match clk driver
ARM: dts: tango4: Initial thermal support
arm/dst: Add Aspeed ast2500 device tree
arm/dts: Add Aspeed ast2400 device tree
ARM: sun7i: dt: Add pll3 and pll7 clocks
ARM: dts: sunxi: Add a olinuxino-lime2-emmc
ARM: dts: at91: sama5d4: add trng node
ARM: dts: at91: sama5d3: add trng node
ARM: dts: at91: sama5d2: add trng node
ARM: dts: at91: at91sam9g45 family: reduce the trng register map size
ARM: sun4i: dt: Add pll3 and pll7 clocks
ARM: sun5i: chip: Enable the TV Encoder
ARM: sun5i: r8: Add display blocks to the DTSI
ARM: sun5i: a13: Add display and TCON clocks
ARM: dts: ux500: configure the accelerometers open drain
ARM: mx5: dts: Enable USB OTG on M53EVK
ARM: dts: imx6ul-14x14-evk: Add audio support
ARM: dts: imx6qdl: Remove unneeded unit-addresses
...
As per the data sheet starting from SPRUHQ0H (Nov 2015 - Latest[1]),
VDD_CORE can vary from 0.85v to 1.15v for AVS class0. VDD GPU/DSP
et.al. can range from 0.85v to 1.25V with AVS class0
Since dynamic voltage scaling is disabled for DRA7/AM57xx SoCs for
all SoC rails other than MPU, the bootloader is responsible for
setting up the AVS class0 voltage, however, with wrong voltage machine
constraints in dtb, regulator framework will lower the voltage below
the required voltage levels for certain samples in production flow.
This can cause catastrophic failures which can be pretty hard to
identify.
Update board files which don't match required specification.
[1] http://www.ti.com/product/AM5728/datasheet/specifications#SPRT637-7340
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
USB1 controller is hardwired to be used as Host only port so
we don't need to check ID pin state and can get rid of extcon_usb1.
This also reduces USB1 controller's and so eSATA power's dependency
with EXTCON. This fixes eSATA port with multi_v7_defconfig.
Cc: Franklin S Cooper Jr. <fcooper@ti.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Franklin S Cooper Jr. <fcooper@ti.com>
[tony@atomide.com: updated to describe what it fixes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since we switched to use eDMA we can now safely enable the FIFO in McASP.
This will reduce the chance of McASP level under/overflow.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The assigned-clock* needs to be in the root of the device's node. If it is
in the sub-node the CCF will ignore it.
Since the clkout2 is used by the codec as MCLK, move the clock parent
selection to that node.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warning:
"sound@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are all the updates to device tree files for 32-bit platforms,
plus a couple of related 64-bit updates:
New SoC support:
- Allwinner A83T
- Axis Artpec-6 SoC
- Mediatek MT7623 SoC
- TI Keystone K2G SoC
- ST Microelectronics stm32f469
New board or machine support:
- ARM Juno R2
- Buffalo Linkstation LS-QVL and LS-GL
- Cubietruck plus
- D-Link DIR-885L
- DT support for ARM RealView PB1176 and PB11MPCore
- Google Nexus 7
- Homlet v2
- Itead Ibox
- Lamobo R1
- LG Optimus Black
- Logicpd dm3730
- Raspberry Pi Model A
Other changes include
- Lots of updates for Qualcomm APQ8064, MSM8974 and others
- Improved support for Nokia N900 and other OMAP machines
- Common clk support for lpc32xx
- HDLCD display on ARM
- Improved stm32f429 support
- Improved Renesas device support, r8a779x and others
- Lots of Rockchip updates
- Samsung cleanups
- ADC support for Atmel SAMA5D2
- BCM2835 (Raspberry Pi) improvements
- Broadcom Northstar Plus enhancements
- OMAP GPMC rework
- Several improvements for Atmel SAMA5D2 / Xplained
- Global change to remove inofficial "arm,amba-bus" compatible string
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RLUc
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"These are all the updates to device tree files for 32-bit platforms,
plus a couple of related 64-bit updates:
New SoC support:
- Allwinner A83T
- Axis Artpec-6 SoC
- Mediatek MT7623 SoC
- TI Keystone K2G SoC
- ST Microelectronics stm32f469
New board or machine support:
- ARM Juno R2
- Buffalo Linkstation LS-QVL and LS-GL
- Cubietruck plus
- D-Link DIR-885L
- DT support for ARM RealView PB1176 and PB11MPCore
- Google Nexus 7
- Homlet v2
- Itead Ibox
- Lamobo R1
- LG Optimus Black
- Logicpd dm3730
- Raspberry Pi Model A
Other changes include
- Lots of updates for Qualcomm APQ8064, MSM8974 and others
- Improved support for Nokia N900 and other OMAP machines
- Common clk support for lpc32xx
- HDLCD display on ARM
- Improved stm32f429 support
- Improved Renesas device support, r8a779x and others
- Lots of Rockchip updates
- Samsung cleanups
- ADC support for Atmel SAMA5D2
- BCM2835 (Raspberry Pi) improvements
- Broadcom Northstar Plus enhancements
- OMAP GPMC rework
- Several improvements for Atmel SAMA5D2 / Xplained
- Global change to remove inofficial "arm,amba-bus" compatible
string"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (350 commits)
ARM, ARM64: dts: drop "arm,amba-bus" in favor of "simple-bus"
ARM: dts: artpec: dual-license on artpec6.dtsi
ARM: dts: ux500: add synaptics RMI4 for Ux500 TVK DT
arm64: dts: juno/vexpress: fix node name unit-address presence warnings
arm64: dts: foundation-v8: add SBSA Generic Watchdog device node
ARM: dts: at91: sama5d2 Xplained: add leds node
ARM: dts: at91: sama5d2 Xplained: add user push button
ARM: dts: at91: sama5d2 Xplained: set pin muxing for usb gadget and usb host
ARM: dts: stm32f429: Enable Ethernet on Eval board
ARM: dts: omap3-sniper: TWL4030 keypad support
Revert "ARM: dts: DRA7: Add dt nodes for PWMSS"
ARM: dts: dm814x: dra62x: Disable wait pin monitoring for NAND
ARM: dts: dm814x: dra62x: Fix NAND device nodes
ARM: dts: stm32f429: Add Ethernet support
ARM: dts: stm32f429: Add system config bank node
ARM: dts: at91: sama5d2: add nand0 and nfc0 nodes
ARM: dts: at91: sama5d2: add dma properties to UART nodes
ARM: dts: at91: sama5d2 Xplained: Correct the macb irq pinctrl node
ARM: dts: exynos: Don't overheat the Odroid XU3-Lite on high load
ARM: dts: exynos: Add cooling levels for Exynos5422/5800 CPUs
...
Detailed description for patchset:
1. Add new EXTCON_CHG_USB_SDP type
- SDP (Standard Downstream Port) USB Charging Port
means the charging connector.a
2. Add the VBUS detection by using GPIO on extcon-palmas
- Beaglex15 board uses the extcon-palmas driver
But, beaglex15 board need the GPIO support for VBUS
detection.
3. Fix the minor issue of extcon drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJW063aAAoJEJzN3yze689ThbEQAJbn/pHDRlw7u8NUiNfRbQWd
uf//IiF2tbJ8eGpCvYIh+dLSlFbFzn3qIETAXJjZ7NfqYpgZsDAwFoMnVF6FfcMG
o2GAVGnUaXge+s+r5PkIwaCRh9LWO5iHJTHjykonhXaKKO4NrHxtsspo/We6Kth4
kmsrmovWd1CvnsvNZJXFSFf37z2eZFG+RYyrveKhFiTlliqyX/DT/RgOqPPPa0UC
9FBXrQ67ibKymX2qYLb5USQnppNFrnzDCacJBiFc2z/kpFFkII7XDrJVogn2JJfZ
M4uQ8JWqBhjrh2yU1FtQ7vuBfk8/Ssbvbp7J+roHJZGwe6AjVY2d3WCRGMLy/fFh
rCfsVvCrwupPVsVj50yTVyEJ0kiDZ9tz3rboWxfuTv/AtRxpUm9gMZ6yE/g2cBl4
RnkYp9dE/Kmu5BaaJZm9yIlHOEgQD/nhXGWm+BdgJBPB2+qAA0D7VPav0Fazjr8O
fN/kyaFHZ5jxSynGVCTsbfD8cJiVWdRzyxwoeXllvGqxwcdgHzX7LrTXrDkRtgC3
5r1B6qgm0kpPxYotrfPI+vAQnR5PGYBa0L4mwXha1rnonwI39QIgg76ZsHyy6k2u
rwGpT3zQmxFs9puf6pFAGmFCaLd1nb5r7FrslkZsn4gG100Gi0ONRRyN6Jx7f7W2
x/EvDnRYTM/pNpNp04Yb
=Zxas
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-testing
Chanwoo writes:
Update extcon for 4.6
Detailed description for patchset:
1. Add new EXTCON_CHG_USB_SDP type
- SDP (Standard Downstream Port) USB Charging Port
means the charging connector.a
2. Add the VBUS detection by using GPIO on extcon-palmas
- Beaglex15 board uses the extcon-palmas driver
But, beaglex15 board need the GPIO support for VBUS
detection.
3. Fix the minor issue of extcon drivers
DRA7 SoC has the capability to support DDR memory upto 4GB. In order to
represent this in memory dt node, the address-cells and size cells
should be 2. So, changing the address-cells and size-cells to 2 and
updating the memory nodes accordingly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add EEPROM at 0x50 that describes the board configuration.
This is useful for userspace programs that may need to check board
revision and other similar information.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The tlv320aic3104 codec's master clock is coming from the SoC's CLKOUT2.
Select the SYS_CLK2 (via divider) as parent clock for CLKOUT2 and select
the same clock (SYS_CLK2) for McASP3 AHCLKX clock as well.
SYS_CLK2 is sourced from an external oscillator running 22.5792MHz and it
is coming in to the SoC via the X1_OSC1.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to latest schematics [1], GPIO_1/VBUSDET
on TPS659038 is tied to AM57x GPIO4_21. We can use
that as a VBUS interrupt, instead of relying on
PMIC's VBUS interrupts which don't seem to be firing
on x15 at all.
A follow up patch will add support for using this
GPIO-based interrupt mechanism for notifying about
VBUS.
[1] https://github.com/beagleboard/beagleboard-x15/blob/master/BeagleBoard-X15_RevA2.pdf
Signed-off-by: Felipe Balbi <balbi@ti.com>
[cw00.choi: Use the 'vbus-gpio' property instead of 'interrupts-extended']
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
According to latest schematics [1], this board
leaves ID pin floating. It's not connected to
anything at all.
So let's remove it.
[1] https://github.com/beagleboard/beagleboard-x15/blob/master/BeagleBoard-X15_RevA2.pdf
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
- Update all omaps to use pinctrl macros. This makes comparing the pinmux
settings against the documentation much earlier. Javier compared the
checksums of the generated dtb files to make sure nothing changed for
the dtb files.
- Updates for dm816x
- Add GPMC DMA channels for am437x
- Updates for LogicPD Torpedo
- Basic support for CompuLab cm-t335
- Remove tps65217.dtsi file, we're better off adding SoC generic board
dtsi files for the common features
- Add support for ELM on am33xx
- Add support for Bosch shc c3 board
- Add qspi aliases for am437x and dra7
- Wake-up support for dra7-evm uart1
- Basic support for CompuLab sbc-t43
- Basic support for CompuLab cl-som-am57x
- Use MMC pwrseq for libertas WLAN on igep0020 and igep0030
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lCuD
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "Device tree changes for omaps for v4.5 merge window" from Tony Lindgren:
- Update all omaps to use pinctrl macros. This makes comparing the pinmux
settings against the documentation much earlier. Javier compared the
checksums of the generated dtb files to make sure nothing changed for
the dtb files.
- Updates for dm816x
- Add GPMC DMA channels for am437x
- Updates for LogicPD Torpedo
- Basic support for CompuLab cm-t335
- Remove tps65217.dtsi file, we're better off adding SoC generic board
dtsi files for the common features
- Add support for ELM on am33xx
- Add support for Bosch shc c3 board
- Add qspi aliases for am437x and dra7
- Wake-up support for dra7-evm uart1
- Basic support for CompuLab sbc-t43
- Basic support for CompuLab cl-som-am57x
- Use MMC pwrseq for libertas WLAN on igep0020 and igep0030
* tag 'omap-for-v4.5/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (97 commits)
ARM: dts: omap3-igep0030: Use MMC pwrseq to init SDIO WiFi
ARM: dts: omap3-igep0020: Use MMC pwrseq to init SDIO WiFi
ARM: dts: am57xx: cl-som-am57x: skip resetting ETH PHYs
ARM: dts: am57xx: sbc-am57x: add HDMI support
ARM: dts: am57xx: compulab-sb-som: add HDMI connector
ARM: dts: am57xx: sbc-am57x: add LCD support
ARM: dts: am57xx: sbc-am57x: add GPIO expander support
ARM: dts: am57xx: sbc-am57x: add EEPROM support
ARM: dts: am57xx: sbc-am57x: add usb vbus pinmux
ARM: dts: am57xx: cl-som-am57x: add MMC1 support
ARM: dts: am57xx: sbc-am57x: add basic board support
ARM: dts: am57xx: cl-som-am57x: add analog audio support
ARM: dts: am57xx: cl-som-am57x: add touchscreen support
ARM: dts: am57xx: cl-som-am57x: add USB support
ARM: dts: am57xx: cl-som-am57x: add dual EMAC support
ARM: dts: am57xx: cl-som-am57x: add spi-flash support
ARM: dts: am57xx: cl-som-am57x: add eMMC support
ARM: dts: am57xx: cl-som-am57x: add EEPROM support
ARM: dts: am57xx: cl-som-am57x: add I2C3 support
ARM: dts: am57xx: cl-som-am57x: dts: add RTC support
...
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since commit 3fffd12839 ("i2c: allow specifying
separate wakeup interrupt in device tree") we have
automatic wakeup irq support for i2c devices. That
commit missed the fact that rtc-1307 had its own
wakeup irq handling and ended up introducing a
kernel splat for at least Beagle x15 boards.
Fix that by reverting original commit _and_ passing
correct interrupt names on DTS so i2c-core can
choose correct IRQ as wakeup.
Now that we have automatic wakeirq support, we can
revert the original commit which did it manually.
Fixes the following warning:
[ 10.346582] WARNING: CPU: 1 PID: 263 at linux/drivers/base/power/wakeirq.c:43 dev_pm_attach_wake_irq+0xbc/0xd4()
[ 10.359244] rtc-ds1307 2-006f: wake irq already initialized
Cc: Tony Lindgren <tony@atomide.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
As usual, this is the massive branch we have for each release. Lots of
various updates and additions of hardware descriptions on existing hardware,
as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and 32-bit
DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to tell
from the diffstat, so there's little point in duplicating listing it here.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qY1q
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, this is the massive branch we have for each release. Lots
of various updates and additions of hardware descriptions on existing
hardware, as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and
32-bit DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to
tell from the diffstat, so there's little point in duplicating listing
it here)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits)
ARM: dts: uniphier: add system-bus-controller nodes
ARM64: juno: disable NOR flash node by default
ARM: dts: uniphier: add outer cache controller nodes
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
dts/ls2080a: Update Simulator DTS to add support of various peripherals
dts/ls2080a: Remove text about writing to Free Software Foundation
dts/ls2080a: Update DTSI to add support of various peripherals
doc: DTS: Update DWC3 binding to provide reference to generic bindings
doc/bindings: Update GPIO devicetree binding documentation for LS2080A
Documentation/dts: Move FSL board-specific bindings out of /powerpc
Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
arm64: Rename FSL LS2085A SoC support code to LS2080A
arm64: Use generic Layerscape SoC family naming
ARM: dts: uniphier: add ProXstream2 Vodka board support
ARM: dts: uniphier: add ProXstream2 Gentil board support
...
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In DRA74x, DRA72x and AM57xx EVMs the card detect gpio is
designed as active low gpio. So correcting the dt card detect
gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
LDO1 regulator (VDD_SD) is connected to SoC's vddshv8. vddshv8 needs to
be kept always powered (see commit 5a0f93c657 ("ARM: dts: Add
am57xx-beagle-x15"), but at the moment VDD_SD is enabled/disabled
depending on whether an SD card is inserted or not.
This patch sets LDO1 regulator to always-on.
This patch has a side effect of fixing another issue, HDMI DDC not
working when SD card is not inserted:
Why this happens is that the tpd12s015 (HDMI level shifter/ESD
protection chip) has LS_OE GPIO input, which needs to be enabled for the
HDMI DDC to work. LS_OE comes from gpio6_28. The pin that provides
gpio6_28 is powered by vddshv8, and vddshv8 comes from VDD_SD.
So when SD card is not inserted, VDD_SD is disabled, and LS_OE stays
off.
The proper fix for the HDMI DDC issue would be to maybe have the pinctrl
framework manage the pin specific power.
Apparently this fixes also a third issue (copy paste from Kishon's
patch):
ldo1_reg in addition to being connected to the io lines is also
connected to the card detect line. On card removal, omap_hsmmc
driver does a regulator_disable causing card detect line to be
pulled down. This raises a card insertion interrupt and once the
MMC core detects there is no card inserted, it does a
regulator disable which again raises a card insertion interrupt.
This happens in a loop causing infinite MMC interrupts.
Fixes: 5a0f93c657 ("ARM: dts: Add am57xx-beagle-x15")
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Louis McCarthy <compeoree@gmail.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the System Mailboxes 5 and 6 and the corresponding child
sub-mailbox (IPC 3.x) nodes for the Beagle X15 EVM boards. This
is needed to enable communication with the respective remote
processors IPU1, IPU2, DSP1 and DSP2 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The analog audio setup consists of:
McASP3 <-> tlv320aic3104 codec
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DVDD is supplied via TPS77018DBVT fixed regulator from vdd_3v3
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The VBUS line of USB2 is connected to VBUS detect logic on
the PMIC. Use the palmas-usb driver to report VBUS events
to the USB driver.
As the palmas-usb driver supports GPIO based ID reporting
provide the GPIO for ID pin as well.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Originally, all the SoC PHY rails were supplied by LDO3. However, as a
result of characterization, it was determined that this posed a risk in
extreme load conditions. Hence the PHY rails are split between two
different LDOs. Update the related node as a result
LDO3/VDDA_1V8_PHYA supplies vdda_usb1, vdda_usb2, vdda_sata, vdda_usb3
LDO4/VDDA_1V8_PHYB supplies vdda_pcie1, vdda_pcie0, vdda_hdmi, vdda_pcie
NOTE: We break compatibility with pre-production boards with this change
since, the PMIC LDO4 is disabled at OTP level.
The new configuration is the plan of record and all pre-production
boards are supposed to be replaced with the latest boards matching the
mentioned configuration.
Some very few 10 something boards have been created and
stopped production till the latest modifications were done (PMIC USB
interrupt, LDO4 etc) - and all of those boards are now getting
scrapped.. If there are any (as per tracking information, there should
not be any), TI should be contacted to have them replaced.
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated commit about these being TI internal protos]
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the support in the generic PM framework for wakeirq and capability
added to the rtc-ds1307 driver to support this, we can now define the
optional wakeup irq to allow the RTC to wakeup the system from low power
modes as part of suspend.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For beagle x15, both the vdd and io lines are connected to the
same regulator (ldo1_reg). However vmmc_aux is populated to vdd_3v3.
Remove it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated to apply]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- Cleanups for Renesas shmobile platforms
- Lots of added devices on LPC18xx
- Lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some branches
that are primarily merged through the clock tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=D2Pm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Ladies and gentlemen, we proudly announce to you the latest branch of
ARM device tree contents for the mainline kernel. Come and see, come
and see!
No less than twentythree thousand lines of additions! Just imagine the
joy you will have of using your mainline kernel on newly supported
hardware such as Rockchip Chromebooks, Freescale i.MX6UL boards or
UniPhier hardware!
For those of you feeling less adventurous, added hardware support on
platforms such as TI DM814x and Gumstix Overo platforms might be more
of your liking.
We've got something for everyone here!
Ahem. Cough. So, anyway...
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- cleanups for Renesas shmobile platforms
- lots of added devices on LPC18xx
- lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some
branches that are primarily merged through the clock tree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (389 commits)
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.
ARM: dts: UniPhier: fix PPI interrupt CPU mask of timer nodes
ARM: dts: rockchip: correct regulator power states for suspend
ARM: dts: rockchip: correct regulator PM properties
ARM: dts: vexpress: Use assigned-clock-parents for sp810
pinctrl: tegra: Only set the gpio range if needed
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: shmobile: r8a7794 dtsi: Add CPG/MSTP Clock Domain
ARM: shmobile: r8a7793 dtsi: Add CPG/MSTP Clock Domain
...
gpio2_8 is connected to the PCIe_RESETn line and it has to be driven low to
reset the PCIe cards. Add gpios property to PCIe DT node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tony Lindgren <tony@atomide.com>
pbias-supply is initialized in dra7.dtsi. Remove redundant initialization
of pbias-supply from MMC1 dt node in am57xx-beagle-x15.dts
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without this USB2 breaks if USB1 is disabled or USB1
initializes after USB2 e.g. due to deferred probing.
Fixes: 5a0f93c657 ("ARM: dts: Add am57xx-beagle-x15")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: stable@vger.kernel.org (v3.19+)
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM57xx Beagle X15 has a HDMI output. This patch adds the device tree
nodes required for HDMI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: devicetree@vger.kernel.org
Acked-by: Tony Lindgren <tony@atomide.com>
BeagleBoard-X15 pre-production change includes switching the GPIO fan
gpio over from 1 to 2 to allow for a potential fix at a later point in
time for USB client VBUS detection using PMIC VBUS detect capability.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBoard-X15 pre-production change includes switching over to UART
pins that now allow for UART download capability. All original boards
should either have been returned for modifications or already modified
for the required change and maintaining compatibility for older boards
are no longer needed.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With commit bc078316d8 ("ARM: dts: DRA7: Add node for RTC"), we now
have AM57xx RTC register itself as alias 0 even before DS1307 or TPS
rtc drivers are loaded up. However, since neither TPS, nor AM57xx RTC
are capable of being backedup by battery, we would like to maintain
the "primary" rtc as mcp79410 rtc device.
This also generates the following warnings in the bootlog highlighting
the issue:
[ 5.895445] rtc-ds1307 2-006f: /aliases ID 0 not available
...
[ 6.476285] palmas-rtc 48070000.i2c:tps659038@58:tps659038_rtc: /aliases ID 1 not available
So, add proper aliases to ensure that RTC order is always consistent
to userspace immaterial of probe order.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The interrupt polarity provided in devicetree is used to configure
the interrupt controller(ARM GIC), however, it seems that we have an
inverter at the GIC boundary inside AM57xx which inverts the signal
input from sys_irq external interrupt source.
Further, as per GIC distributor TRM,
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0438d/BGBHIACJ.html#BABJFCFB
ARM GIC distributor does not support IRQ trigger type
IRQ_TYPE_LEVEL_LOW, and only rising or level high signals.
However, for some reason, the current configuration(which gets ignored
by GIC driver) functions on some platforms, however, on few platforms
results in infinite interrupts hogging the system down.
Switch over to rising edge for GIC configuration which is also aligned
with trigger point from the RTC chip and the internal inversion.
Fixes: 5a0f93c657 ("ARM: dts: Add am57xx-beagle-x15")
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As always, this tends to be one of our bigger branches. There are lots of
updates this release, but not that many jumps out as something that needs
more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- More graphics DT pieces falling into place on Exynos, bridges, clocks.
- Plenty of DT updates for Qualcomm platforms for various IP blocks
- Some churn on Tegra due to switch-over to tool-generated pinctrl data
- Misc fixes and updates for Atmel at91 platforms
- Various DT updates to add IP block support on Broadcom's Cygnus platforms
- More updates for Renesas platforms as DT support is added for various IP
blocks (IPMMU, display, audio, etc).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wqhB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As always, this tends to be one of our bigger branches. There are
lots of updates this release, but not that many jumps out as something
that needs more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- more graphics DT pieces falling into place on Exynos, bridges,
clocks.
- plenty of DT updates for Qualcomm platforms for various IP blocks
- some churn on Tegra due to switch-over to tool-generated pinctrl
data
- misc fixes and updates for Atmel at91 platforms
- various DT updates to add IP block support on Broadcom's Cygnus
platforms
- more updates for Renesas platforms as DT support is added for
various IP blocks (IPMMU, display, audio, etc)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (231 commits)
ARM: dts: alpine: add internal pci
Revert "ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135."
ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB
ARM: dts: qcom: Add idle state device nodes for 8064
ARM: dts: qcom: Add idle states device nodes for 8084
ARM: dts: qcom: Add idle states device nodes for 8974/8074
ARM: dts: qcom: Update power-controller device node for 8064 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8084 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8074 Krait CPUs
devicetree: bindings: Document qcom,idle-states
devicetree: bindings: Update qcom,saw2 node bindings
dt-bindings: Add #defines for MSM8916 clocks and resets
arm: dts: qcom: Add LPASS Audio HW to IPQ8064 device tree
arm: dts: qcom: Add APQ8084 chipset SPMI PMIC's nodes
arm: dts: qcom: Add 8x74 chipset SPMI PMIC's nodes
arm: dts: qcom: Add SPMI PMIC Arbiter nodes for APQ8084 and MSM8974
arm: dts: qcom: Add LCC nodes
arm: dts: qcom: Add TCSR support for MSM8960
arm: dts: qcom: Add TCSR support for MSM8660
arm: dts: qcom: Add TCSR support for IPQ8064
...
Here's the usual "low-priority fixes that didn't make it into the last
few -rcs, with a twist: We had a fixes pull request that I didn't send
in time to get into 4.0, so we'll send some of them to Greg for -stable as
well.
Contents here is as usual not all that controversial:
- A handful of randconfig fixes from Arnd, in particular for older Samsung
platforms
- Exynos fixes, !SMP building, DTS updates for MMC and lid switch
- Kbuild fix to create output subdirectory for DTB files
- Misc minor fixes for OMAP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o/4N
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's the usual "low-priority fixes that didn't make it into the last
few -rcs, with a twist: We had a fixes pull request that I didn't send
in time to get into 4.0, so we'll send some of them to Greg for
-stable as well.
Contents here is as usual not all that controversial:
- a handful of randconfig fixes from Arnd, in particular for older
Samsung platforms
- Exynos fixes, !SMP building, DTS updates for MMC and lid switch
- Kbuild fix to create output subdirectory for DTB files
- misc minor fixes for OMAP"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: at91/dt: sama5d3 xplained: add phy address for macb1
kbuild: Create directory for target DTB
ARM: mvebu: Disable CPU Idle on Armada 38x
ARM: DRA7: Enable Cortex A15 errata 798181
ARM: dts: am57xx-beagle-x15: Add thermal map to include fan and tmp102
ARM: dts: DRA7: Add bandgap and related thermal nodes
bus: ocp2scp: SYNC2 value should be changed to 0x6
ARM: dts: am4372: Add "ti,am437x-ocp2scp" as compatible string for OCP2SCP
ARM: OMAP2+: remove superfluous NULL pointer check
ARM: EXYNOS: Fix build breakage cpuidle on !SMP
ARM: dts: fix lid and power pin-functions for exynos5250-spring
ARM: dts: fix mmc node updates for exynos5250-spring
ARM: OMAP4: remove dead kconfig option OMAP4_ERRATA_I688
MAINTAINERS: add OMAP defconfigs under OMAP SUPPORT
ARM: OMAP1: PM: fix some build warnings on 1510-only Kconfigs
ARM: cns3xxx: don't export static symbol
ARM: S3C24XX: avoid a Kconfig warning
ARM: S3C24XX: fix header file inclusions
ARM: S3C24XX: fix building without PM_SLEEP
ARM: S3C24XX: use SAMSUNG_WAKEMASK for s3c2416
...
- Purge the gic_arch_extn hacks and abuse by using the new stacked domains
NOTE: Due to the nature of these changes, patches crossing subsystems have
been kept together in their own branches.
- tegra
- Handle the LIC properly
- omap
- Convert crossbar to stacked domains
- kill arm,routable-irqs in GIC binding
- exynos
- Convert PMU wakeup to stacked domains
- shmobile, ux500, zynq (irq_set_wake branch)
- Switch from abusing gic_arch_extn to using gic_set_irqchip_flags
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJVKFhRAAoJEP45WPkGe8ZnYFcP/iBznjkMYG+OUwrxo7G4rTyu
JYj0dmg/D76ewFsxWFv24II9V+KJaqrEtFTHH4MVbeEbbrDIx7Am0i/Ip6rDRgxS
7Q/jGic8etfPGV8gW6x38zbTHOl1rfqQtoHcqBH5FnLITuMAuHPa51jpwhMik4ri
AbMwb6Whep6tEsxiEjspPxXWphEZoXluOkRjPLokTwuifo4rEo7bqU8WMizzSW5g
xEjf8eUvBYIMTA40FBQWHQwxf1jRySSW2A9u5JgT1ccZHoajEyDgQr22KUHpCAWU
hlZ/8uTqCUeecDQKFPr4zXhq9mbEVZ7lld5Gl82cxY6aI3Xj/bUI3tSYubPWEgx6
0VhbmvjqKPiFfdCrLq5ZTY5UHmW8khdttdycIPNz9LmUDVgIzJpmpAW+oyG7BN/N
QgGF4lzaN49mHQmjtXGfwY3iJTadxyVaWoZTBinjw8LyxpzUO/MNQGLumsxEtkxN
Nbbsc2k+ERpSx40ospB1WOslAzMsNi6eLwqLRfjGGfSYK1P6Mm7FhansJm08p1/D
8h6ymqA4heZrYdI1vrfuy7QuEqQgnVUf0TDTHxX+aNGrHnBSsPTTfYHBOHXUh4Cr
Ox3yLECAhWle4VlgInu3XLRmuUiYGk4JV4nbZUjpZvIaOZV4gLArcsQU7C/KTDT8
CqrybDOIxFkIbxfU+EE0
=IPgJ
-----END PGP SIGNATURE-----
Merge tag 'irqchip-core-4.1-3' of git://git.infradead.org/users/jcooper/linux into irq/core
irqchip core change for v4.1 (round 3) from Jason Cooper
Purge the gic_arch_extn hacks and abuse by using the new stacked domains
NOTE: Due to the nature of these changes, patches crossing subsystems have
been kept together in their own branches.
- tegra
- Handle the LIC properly
- omap
- Convert crossbar to stacked domains
- kill arm,routable-irqs in GIC binding
- exynos
- Convert PMU wakeup to stacked domains
- shmobile, ux500, zynq (irq_set_wake branch)
- Switch from abusing gic_arch_extn to using gic_set_irqchip_flags
This is mostly to enable errata 798181 and thermal support for dra7,
configure ocp2scp for am437x, remove dead code for OMAP4_ERRATA_I688
and fix build warnings for omap1510 only config.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Uqd0
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/fixes-0' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge "omap non-urgent fixes for v4.1" from Tony Lindgren:
Fixes for omaps that were not considered urgent enough for the -rc cycle.
This is mostly to enable errata 798181 and thermal support for dra7,
configure ocp2scp for am437x, remove dead code for OMAP4_ERRATA_I688
and fix build warnings for omap1510 only config.
* tag 'omap-for-v4.1/fixes-0' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: DRA7: Enable Cortex A15 errata 798181
ARM: dts: am57xx-beagle-x15: Add thermal map to include fan and tmp102
ARM: dts: DRA7: Add bandgap and related thermal nodes
bus: ocp2scp: SYNC2 value should be changed to 0x6
ARM: dts: am4372: Add "ti,am437x-ocp2scp" as compatible string for OCP2SCP
ARM: OMAP2+: remove superfluous NULL pointer check
ARM: OMAP4: remove dead kconfig option OMAP4_ERRATA_I688
MAINTAINERS: add OMAP defconfigs under OMAP SUPPORT
ARM: OMAP1: PM: fix some build warnings on 1510-only Kconfigs
Signed-off-by: Olof Johansson <olof@lixom.net>
BeagleBoard-X15 has capability for a fan and has an onboard TMP102
temperature sensor as well. This allows us to create a new thermal
zone (called, un-imaginatively "board"), and allows us to use some
active cooling as temperatures start edge upward in the system by
creating a new alert temperature (emperically 50C) for cpu.
NOTE: Fan is NOT mounted by default on the platform, in such a case,
all we end up doing is switch on a regulator and leak very minimal
current.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we have EXTCON_USB_GPIO queued for v4.1, revert
commit addfcde7c4 ("ARM: dts: dra7x-evm: beagle-x15: Fix USB Host")
On these EVMs, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).
Gets USB peripheral mode to work on this EVM.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Support for the TI crossbar used on the DRA7 family of chips
is implemented as an ugly hack on the side of the GIC.
Converting it to stacked domains makes it slightly more
palatable, as it results in a cleanup.
Unfortunately, as the DT bindings failed to acknowledge the
fact that this is actually yet another interrupt controller
(the third, actually), we have yet another breakage. Oh well.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088629-15377-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
