For Lynxpoint and Wildcat Point solution, is it host's responsibility to
allocate SRAM regions and ensure those already taken are not overwritten
with other data until released. Blocks are transferred to SRAM - either
IRAM or DRAM - via DW DMA controller. Once basefw is booted, ownership
of DMA transfer is lost in favour of DSP.
Hosts reponsibilities don't end on initial block allocation and binary
transfer. During Dx transitions host must store FW runtime context from
DRAM before putting AudioDSP subsystem into lower power state. Said
context gets flashed after D0 entry to bring DSP right where it was just
before suspending.
Load and restore procedures are finalized with SRAM power gating and
adequate clock level selection. This power gates unused EBBs and clock
speed effectively reducing power consumption.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200929141247.8058-6-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement dsp lifecycle functions such as core RESET and STALL,
SRAM power control and LP clock selection. This also adds functions for
handling transport over DW DMA controller.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200929141247.8058-5-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare global and stream IPC message handlers for all known message
types.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200929141247.8058-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement IRQ handlers for immediate and delayed replies and
notifications. Communication is synchronous and allows for serialization
of maximum one message at a time.
DSP may respond with ADSP_PENDING status for a request - known as
delayed reply - and when situation occurs, framework keeps the lock and
awaits upcoming response through IPCD channel which is handled in
bottom-half. Immediate replies spawn no BH at all as their processing is
very short.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200929141247.8058-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare base structures, registers and extension routines for the catpt
solution.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200929141247.8058-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Update list of SSP registers with SSC2 and SSPSP2. These registers are
utilized by LPT/WPT AudioDSP architecture.
While SSC2 shares the same offset (0x40) as SSACDD, description of this
register for SSP device present on mentioned AudioDSP is different so
define separate constant to avoid any ambiguity.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200825201743.4926-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function fsl_spdif_probe() is only called with an openfirmware
platform device. Therefore there is no need to check that the passed
in device is NULL.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20200826150918.16116-1-tangbin@cmss.chinamobile.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The binding was added in 2013 and has had no driver since 2015.
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200826184851.3431531-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 140a4532cd ("ASoC: soc-pcm: add soc_pcm_clean() and call it
from soc_pcm_open/close()") switched to use soc_pcm_clean() at
soc_pcm_open().
But it removed "return 0", and missing "ret = 0",
because of it, it always return -EINVAL eventhough no error.
This patch adds missing "ret = 0" for success case.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/87ft6ya65z.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 140a4532cd ("ASoC: soc-pcm: add soc_pcm_clean() and call it
from soc_pcm_open/close()") switch to call soc_pcm_clean() on
soc_pcm_open() when rollback case.
But, it uses "goto err" (A) *before* mutex_lock() (B) when error of
snd_soc_pcm_component_pm_runtime_get().
The mutex_unlock() (C) is not needed in such case. This patch fix it.
static int soc_pcm_open(...)
{
...
ret = snd_soc_pcm_component_pm_runtime_get(rtd, substream);
if (ret < 0)
(A) goto err;
(B) mutex_lock_nested(...);
...
err:
(C) mutex_unlock(..);
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87k0waag44.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20200922015123.117489-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 95e0e07e71 ("ASoC: atmel-pcm: use generic dmaengine
framework"), the driver is using dmaengine and is not using any definition
from include/linux/platform_data/dma-atmel.h, stop including it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200930145330.3043528-1-alexandre.belloni@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit d5fab59cab ("spi: atmel: trivial: remove unused fields in
DMA structure"), the driver is not using any definitions from
linux/platform_data/dma-atmel.h, stop including it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200930145353.3043699-1-alexandre.belloni@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi Mark
1 month past and nothing happened.
This is resend of v2 patch-set.
soc_pcm_open() does rollback when failed (A),
but, it is almost same as soc_pcm_close().
static int soc_pcm_open(xxx)
{
...
if (ret < 0)
goto xxx_err;
...
return 0;
^ config_err:
| ...
| rtd_startup_err:
(A) ...
| component_err:
| ...
v return ret;
}
This kind of duplicated code can be a hotbed of bugs,
thus, this patch-set share soc_pcm_close() and rollback.
v1 -> v2
- indicate more detail background/logic on git-log
Link: https://lore.kernel.org/r/87wo2oku0m.wl-kuninori.morimoto.gx@renesas.com
Link: https://lore.kernel.org/r/87wo1kvozz.wl-kuninori.morimoto.gx@renesas.com
Kuninori Morimoto (7):
ASoC: soc-dai: add mark for snd_soc_dai_startup/shutdown()
ASoC: soc-link: add mark for snd_soc_link_startup/shutdown()
ASoC: soc-component: add mark for soc_pcm_components_open/close()
ASoC: soc-component: add mark for
snd_soc_pcm_component_pm_runtime_get/put()
ASoC: soc-pcm: add soc_pcm_clean() and call it from
soc_pcm_open/close()
ASoC: soc-pcm: remove unneeded dev_err() for snd_soc_dai_startup()
ASoC: soc-pcm: remove unneeded dev_err() for
snd_soc_component_module/open()
include/sound/soc-component.h | 28 +++++---
include/sound/soc-dai.h | 5 +-
include/sound/soc-link.h | 3 +-
include/sound/soc.h | 3 +
sound/soc/soc-component.c | 73 ++++++++++++++++++++-
sound/soc/soc-compress.c | 30 +++------
sound/soc/soc-dai.c | 21 +++++-
sound/soc/soc-dapm.c | 4 +-
sound/soc/soc-link.c | 21 +++++-
sound/soc/soc-pcm.c | 120 ++++++++++++----------------------
10 files changed, 190 insertions(+), 118 deletions(-)
--
2.25.1
use new devm_regmap_field_bulk_alloc to allocate fields as
it make the code more readable!
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Link: https://lore.kernel.org/r/20200925164856.10315-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Useful for devices with many fields.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9yPoATHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0JsoB/9zhtYrqKbof0AKuMfEeO+pPo4dC/9l
O7ENgSXCb9PWy0auVpU62ISXBPadbbrQXXe3hJ1Zof5q17lYqbaLM7Uem3bxIYtc
0HHRIb49R1sP+99T2JB3RDu/ykzHJsfxCkLgMR5MvBgS5e3KKf0SqZgNSVTYT4Y5
oPt81sxW56Z8FLrLn0j1sVDXlro4/uBpDOcHyzgq4GWgQ6ACvnIOH+PQUTTcGBfT
LtIkRMO8mHNKsDCy9Qy12NRsaparIbYb7KKEY9IR+6TN+qJ/g5PJQcPmsU6b0NIl
pb7fv4IRTvPDaEPa1g20U88qkSE5H3PXp88R3y/JbSMuFJwWwS2AGwYd
=L+6w
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9yPsMTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0EAjB/kB2oYbW/o8DN+Vy6t5ipMiI90R8gVQ
9lXF1nCeH8VPXukL0fYC5hmZKch6m9gmxThDGQdejB2yAzPSD0bQcqVeJxmtvlbc
sFfVXtujKosw6gZ8CDYvhcX71oLWso1aRt7XivrKuMG5xoQltfH1s+66LQdmU339
RpnpipUbVdDsnO/Ual29TKXoh84N02IlgwooyvUckQdxy9pypR5P1X0XUQM5lLXZ
52SA4PAEtyF/bBvriHMuCDeb6squ/GPLZ7z8fdeQeWfJG9Oc0spF8JM8fIjBIJOH
jNLAI4dge1oW/ijN6LTJ72M/P5KUZXC8Ah+A2o1fFFjYcbmZ9IEm7a4r
=JE/v
-----END PGP SIGNATURE-----
Merge tag 'regmap-field-bulk-api' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into asoc-5.10
regmap: Add a bulk field API
Useful for devices with many fields.
Usage of regmap_field_alloc becomes much overhead when number of fields
exceed more than 3.
QCOM LPASS driver has extensively converted to use regmap_fields.
Using new bulk api to allocate fields makes it much more cleaner code to read!
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Link: https://lore.kernel.org/r/20200925164856.10315-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS4234 is a highly versatile CODEC that combines 4 channels of
high performance analog to digital conversion, 4 channels of high
performance digital to analog conversion for audio, and 1 channel of
digital to analog conversion to provide a nondelayed audio reference
signal to an external Class H tracking power supply.
DAC5 is only supported as a 5th audio channel. Tracking Power Supply
mode is not currently supported by the driver.
In DSP_A mode the slots for DAC1-4 and optionally DAC5 can be set.
The codec always claims 4 slots for DAC1-4 and these must be in the
same nibble of the mask. The codec has a fixed mapping for ADC slots.
In I2S/LJ modes the codec has a fixed mapping for DAC1-4 and ADC1-4.
DAC5 is not available in these modes.
The MCLK source must be preset to a valid frequency before probe()
because it must be running all the time the codec is out of reset.
The VA_SEL bit will be set automatically to 3.3v or 5v during probe()
based on the reported voltage of the regulator supplying VA.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200928111821.26967-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the use of of_match_ptr() macro for of_match_table to fix compiler
warning when CONFIG_OF=n:
sound/soc/ti/j721e-evm.c:528:34: warning: unused variable 'j721e_audio_of_match' [-Wunused-const-variable]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200928074330.13029-1-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add 400ms power-up delay recommended to fix pop noise on capture.
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200925210509.83353-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add common properties appearing in DTSes (assigned-clocks and similar)
to fix dtbs_check warnings like:
arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dt.yaml: audio-codec@a:
'assigned-clock-parents', 'assigned-clock-rates', 'assigned-clocks' do not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200925212719.23286-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_component_module_get(), snd_soc_component_open() itself will
indicate error message, thus, soc_pcm_components_open() don't need to
handle it.
This patch removes these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87d026bwms.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_startup() itself will indicate error message,
thus, soc_pcm_open() don't need to handle it.
This patch removes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87eemmbwmy.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
soc_pcm_open() does rollback when failed (A),
but, it is almost same as soc_pcm_close().
static int soc_pcm_open(xxx)
{
...
if (ret < 0)
goto xxx_err;
...
return 0;
^ config_err:
| ...
| rtd_startup_err:
(A) ...
| component_err:
| ...
v return ret;
}
The difference is
soc_pcm_close() is for all dai/component/substream,
rollback is for succeeded part only.
This kind of duplicated code can be a hotbed of bugs,
thus, we want to share soc_pcm_close() and rollback.
Now, soc_pcm_open/close() are handling
1) snd_soc_dai_startup/shutdown()
2) snd_soc_link_startup/shutdown()
3) snd_soc_component_module_get/put()
4) snd_soc_component_open/close()
5) pm_runtime_put/get()
Now, 1) to 5) are handled.
This patch adds new soc_pcm_clean() and call it from
soc_pcm_open() as rollback, and from soc_pcm_close() as
normal close handler.
One note here is that it don't need to call snd_soc_runtime_deactivate()
when rollback case, because it will be called without
snd_soc_runtime_activate().
It also don't need to call snd_soc_dapm_stream_stop() when rollback case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87ft72bwn4.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
soc_pcm_open() does rollback when failed (A),
but, it is almost same as soc_pcm_close().
static int soc_pcm_open(xxx)
{
...
if (ret < 0)
goto xxx_err;
...
return 0;
^ config_err:
| ...
| rtd_startup_err:
(A) ...
| component_err:
| ...
v return ret;
}
The difference is
soc_pcm_close() is for all dai/component/substream,
rollback is for succeeded part only.
This kind of duplicated code can be a hotbed of bugs,
thus, we want to share soc_pcm_close() and rollback.
Now, soc_pcm_open/close() are handling
1) snd_soc_dai_startup/shutdown()
2) snd_soc_link_startup/shutdown()
3) snd_soc_component_module_get/put()
4) snd_soc_component_open/close()
=> 5) pm_runtime_put/get()
This patch is for 5) pm_runtime_put/get().
The idea of having bit-flag or counter is not enough for this purpose.
For example if one DAI is used for 2xPlaybacks for some reasons,
and if 1st Playback was succeeded but 2nd Playback was failed,
2nd Playback rollback doesn't need to call shutdown.
But it has succeeded bit-flag or counter via 1st Playback,
thus, 2nd Playback rollback will call unneeded shutdown.
And 1st Playback's necessary shutdown will not be called,
because bit-flag or counter was cleared by wrong 2nd Playback rollback.
To avoid such case, this patch marks substream pointer when get() was
succeeded. If rollback needed, it will check rollback flag and marked
substream pointer.
One note here is that it cares *current* get() only now.
but we might want to check *whole* marked substream in the future.
This patch is using macro named "push/pop", so that it can be easily
update.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87h7ribwnb.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
soc_pcm_open() does rollback when failed (A),
but, it is almost same as soc_pcm_close().
static int soc_pcm_open(xxx)
{
...
if (ret < 0)
goto xxx_err;
...
return 0;
^ config_err:
| ...
| rtd_startup_err:
(A) ...
| component_err:
| ...
v return ret;
}
The difference is
soc_pcm_close() is for all dai/component/substream,
rollback is for succeeded part only.
This kind of duplicated code can be a hotbed of bugs,
thus, we want to share soc_pcm_close() and rollback.
Now, soc_pcm_open/close() are handling
1) snd_soc_dai_startup/shutdown()
2) snd_soc_link_startup/shutdown()
=> 3) snd_soc_component_module_get/put()
=> 4) snd_soc_component_open/close()
5) pm_runtime_put/get()
This patch is for 3) snd_soc_component_module_get/put()
4) snd_soc_component_open/close().
The idea of having bit-flag or counter is not enough for this purpose.
For example if one DAI is used for 2xPlaybacks for some reasons,
and if 1st Playback was succeeded but 2nd Playback was failed,
2nd Playback rollback doesn't need to call shutdown.
But it has succeeded bit-flag or counter via 1st Playback,
thus, 2nd Playback rollback will call unneeded shutdown.
And 1st Playback's necessary shutdown will not be called,
because bit-flag or counter was cleared by wrong 2nd Playback rollback.
To avoid such case, this patch marks substream pointer when open() was
succeeded. If rollback needed, it will check rollback flag and marked
substream pointer.
One note here is that it cares *current* open() only now.
but we might want to check *whole* marked substream in the future.
This patch is using macro named "push/pop", so that it can be easily
update.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87imbybwno.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
soc_pcm_open() does rollback when failed (A),
but, it is almost same as soc_pcm_close().
static int soc_pcm_open(xxx)
{
...
if (ret < 0)
goto xxx_err;
...
return 0;
^ config_err:
| ...
| rtd_startup_err:
(A) ...
| component_err:
| ...
v return ret;
}
The difference is
soc_pcm_close() is for all dai/component/substream,
rollback is for succeeded part only.
This kind of duplicated code can be a hotbed of bugs,
thus, we want to share soc_pcm_close() and rollback.
Now, soc_pcm_open/close() are handling
1) snd_soc_dai_startup/shutdown()
=> 2) snd_soc_link_startup/shutdown()
3) snd_soc_component_module_get/put()
4) snd_soc_component_open/close()
5) pm_runtime_put/get()
This patch is for 2) snd_soc_link_startup/shutdown().
The idea of having bit-flag or counter is not enough for this purpose.
For example if one DAI is used for 2xPlaybacks for some reasons,
and if 1st Playback was succeeded but 2nd Playback was failed,
2nd Playback rollback doesn't need to call shutdown.
But it has succeeded bit-flag or counter via 1st Playback,
thus, 2nd Playback rollback will call unneeded shutdown.
And 1st Playback's necessary shutdown will not be called,
because bit-flag or counter was cleared by wrong 2nd Playback rollback.
To avoid such case, this patch marks substream pointer when startup() was
succeeded. If rollback needed, it will check rollback flag and marked
substream pointer.
One note here is that it cares *current* startup() only now.
but we might want to check *whole* marked substream in the future.
This patch is using macro named "push/pop", so that it can be easily
update.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87k0webwnv.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
soc_pcm_open() does rollback when failed (A),
but, it is almost same as soc_pcm_close().
static int soc_pcm_open(xxx)
{
...
if (ret < 0)
goto xxx_err;
...
return 0;
^ config_err:
| ...
| rtd_startup_err:
(A) ...
| component_err:
| ...
v return ret;
}
The difference is
soc_pcm_close() is for all dai/component/substream,
rollback is for succeeded part only.
This kind of duplicated code can be a hotbed of bugs,
thus, we want to share soc_pcm_close() and rollback.
Now, soc_pcm_open/close() are handling
=> 1) snd_soc_dai_startup/shutdown()
2) snd_soc_link_startup/shutdown()
3) snd_soc_component_module_get/put()
4) snd_soc_component_open/close()
5) pm_runtime_put/get()
This patch is for 1) snd_soc_dai_startup/shutdown().
The idea of having bit-flag or counter is not enough for this purpose.
For example if one DAI is used for 2xPlaybacks for some reasons,
and if 1st Playback was succeeded but 2nd Playback was failed,
2nd Playback rollback doesn't need to call shutdown.
But it has succeeded bit-flag or counter via 1st Playback,
thus, 2nd Playback rollback will call unneeded shutdown.
And 1st Playback's necessary shutdown will not be called,
because bit-flag or counter was cleared by wrong 2nd Playback rollback.
To avoid such case, this patch marks substream pointer when startup() was
succeeded. If rollback needed, it will check rollback flag and marked
substream pointer.
One note here is that it cares *current* startup() only now.
but we might want to check *whole* marked substream in the future.
This patch is using macro named "push/pop", so that it can be easily
update.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87lfgubwoc.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Looks like there was a major typo in SPDX Licence version,
Not sure how it was missed.
This patch is to fix it.
Reported-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200926171844.7792-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Daniel Baluta <daniel.baluta@nxp.com>:
From: Daniel Baluta <daniel.baluta@nxp.com>
This enables runtime PM for SOF device. Next patchseries will
provide PM suspend/resume handlers for i.MX8 specific devices.
Daniel Baluta (2):
ASoC: SOF: Activate runtime PM with SOF OF device
ASoC: SOF: Add .prepare/.complete callbacks
sound/soc/sof/sof-of-dev.c | 6 ++++++
1 file changed, 6 insertions(+)
--
2.17.1
Here are fixes for two warnings types discovered while building qdsp6 drivers
without CONFIG_OF and with W=1
One of them was reported by Intel kernel test robot on q6afe-clocks patch, which
equally applies to rest of the qdsp6 drivers.
changes since v1:
- added ifdef CONFIG_OF instead of removing of_match_ptr
Srinivas Kandagatla (2):
ASoC: qdsp6: add ifdef CONFIG_OF around of_device_id
ASoC: q6asm: fix kernel doc warnings
sound/soc/qcom/qdsp6/q6adm.c | 2 ++
sound/soc/qcom/qdsp6/q6afe-clocks.c | 2 ++
sound/soc/qcom/qdsp6/q6afe-dai.c | 2 ++
sound/soc/qcom/qdsp6/q6afe.c | 2 ++
sound/soc/qcom/qdsp6/q6asm-dai.c | 2 ++
sound/soc/qcom/qdsp6/q6asm.c | 6 ++++++
sound/soc/qcom/qdsp6/q6core.c | 2 ++
sound/soc/qcom/qdsp6/q6routing.c | 2 ++
8 files changed, 20 insertions(+)
--
2.21.0
Update lpass-cpu.c to enable I2S BCLK and LRCLK together.
Remove BCLK enable in lpass_cpu_daiops_startup and
add in lpass_cpu_daiops_trigger API.
Signed-off-by: V Sujith Kumar Reddy <vsujithk@codeaurora.org>
Signed-off-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Link: https://lore.kernel.org/r/1600448073-6709-1-git-send-email-srivasam@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "devm_kcalloc".
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20200921015918.24157-1-vulab@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Use SOF defined callbacks (snd_sof_prepare/snd_sof_complete)
in order to update internal SOF system suspend target.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@nxp.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20200924151518.15841-3-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SOF boots the DSP at probe and keeps it up all the time.
With this change, after booting if no one is using the DSP
the SOF core will turn off the DSP to save power.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@nxp.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20200924151518.15841-2-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes below kernel doc warnings on not describing all the parmeters
sound/soc/qcom/qdsp6/q6asm.c:927: warning: Function parameter or member
'stream_id' not described in 'q6asm_open_write'
sound/soc/qcom/qdsp6/q6asm.c:927: warning: Function parameter or member
'is_gapless' not described in 'q6asm_open_write'
sound/soc/qcom/qdsp6/q6asm.c:1053: warning: Function parameter or member
'stream_id' not described in 'q6asm_run'
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200925163552.20717-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add ifdef CONFIG_OF around of_device_id table to fix below
W=1 compile test warning with !CONFIG_OF:
sound/soc/qcom/qdsp6/q6afe-clocks.c:254:34: warning: unused variable
'q6afe_clock_device_id' [-Wunused-const-variable]
Fix this warning for across all qdsp6 drivers.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200925163552.20717-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove unused variables in the private struct and the code as these
variables are initially set and then there is no additional code
utilizing these variables.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200923132600.10652-6-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the code to support the asi-format binding property. The code
does nothing except read the property and set a variable. No additional
action is taken except to reset the variable. The property is supposed
to set the rising or falling RX edge detection of the SBCLK but this
edge detection is done by checking the DAI_FMT_INV_MASK.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200923132600.10652-5-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
