This patch prepares the introduction of the generic PHY support in the
USB OTG common functions. The USB PHY member of the OTG structure is
renamed to 'usb_phy' and modifications are done in all drivers accessing
it. Renaming this pointer will allow to keep the compatibility for USB
PHY drivers.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before using the PHY framework instead of the USB PHY one, we need to
move the OTG state into another place, since it won't be available when
USB PHY isn't used. This patch moves the OTG state into the OTG
structure, and makes all the needed modifications in the drivers
using the OTG state.
[ balbi@ti.com : fix build regressions with phy-tahvo.c, musb_dsps.c,
phy-isp1301-omap, and chipidea's debug.c ]
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that no UDC driver relies on the extra
'driver' argument to ->udc_stop(), we can
safely remove it.
This commit is based on previous work by
Robert Baldyga <r.baldyga@samsung.com> which
can be found at [1]; however that patch turned
out to have a high probability of regressing
many UDC drivers because of a blind search & replace
s/driver/$udc->driver/ which caused the 'driver'
argument to stop_activity() to be a valid non-NULL
pointer when it should be NULL, thus causing UDCs
to mistakenly call gadget driver's ->disconnect()
callback.
[1] http://markmail.org/message/x5zneg4xea4zntab
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB gadgets composed with configfs lack suspend and resume
methods. This patch uses composite_suspend()/composite_resume()
the same way e.g. composite_setup() or composite_disconnect()
are used in a configfs-based gadget.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These flags we be set to true whenever their
matching request is queued. They will be cleared
to false when that request completes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
To delegate promiscuous mode and multicast filtering to the subdriver.
Signed-off-by: Olivier Blin <olivier.blin@softathome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the generic PHY support, analogous to the USB PHY support. Intended it to be
used with the PCI EHCI/OHCI drivers and the xHCI platform driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB PHY member of the HCD structure is renamed to 'usb_phy' and
modifications are done in all drivers accessing it.
This is in preparation to adding the generic PHY support.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
[Sergei: added missing 'drivers/usb/misc/lvstest.c' file, resolved rejects,
updated changelog.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All USB peripheral controller drivers call completion routines directly.
This patch adds usb_gadget_giveback_request() which will be used instead
of direct invocation in the next patch. The goal here is to have a place
where common functionality can be added.
Signed-off-by: Michal Sojka <sojka@merica.cz>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the BIT macro instead of "open coding" bit fields. This makes it
easier to actually see that the bits are not conflicting/overlapping.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This full-speed USB device generates spurious remote wakeup event
as soon as USB_DEVICE_REMOTE_WAKEUP feature is set. As the result,
Linux can't enter system suspend and S0ix power saving modes once
this keyboard is used.
This patch tries to introduce USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk.
With this quirk set, wakeup capability will be ignored during
device configure.
This patch could be back-ported to kernels as old as 2.6.39.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For OTG and Embedded hosts, they may need TPL (Targeted Peripheral List)
for usb certification and other vender specific requirements, the
platform can tell chipidea core driver if it supports tpl through DT
or platform data.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TPL (Targeted Peripheral List) is used for targeted hosts
(non-PC hosts), and it can be used at USB OTG & EH certification
and some specific products which need white list.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The targeted hosts (non-PC hosts) need to have TPL (Targeted Peripheral List)
for USB OTG & EH certification and other vendor specific requirements.
The platform who needs TPL feature should set this flag at usb host
controller driver.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new quirk for devices that cannot handle requests for the
device_qualifier descriptor.
A USB-2.0 compliant device must respond to requests for the
device_qualifier descriptor (even if it's with a request error), but at
least one device is known to misbehave after such a request.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The udc driver can notify the udc core that bus reset occurs by
calling this utility, the core will notify gadget driver this
information and update gadget state accordingly.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adding reset API for UDC bus reset handler is useful for below
two issues.
Current disconnect API at usb_gadget_driver is also invoked at
udc's bus reset handler, but the document says it is invoked when
the host is disconnected.
Besides, we may expect the gadget_driver to do different things
for host sends bus reset and host disconnects gadget, eg, we may not
want to flush dirty page for mass storage at bus reset, and want to
do it at disconnection.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Document the requirement that the request be dequeued and its
completion routine called before usb_ep_dequeue() returns. Also
fix some capitalization issues in the existing text.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
This device needs to be reset to recover from a timeout.
Unfortunately this can be handled only at the level of
the subdrivers.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a usb quirk to support devices with interupt endpoints
and bInterval values expressed as microframes. The quirk causes the
parse endpoint function to modify the reported bInterval to a standards
conforming value.
There is currently code in the endpoint parser that checks for
bIntervals that are outside of the valid range (1-16 for USB 2+ high
speed and super speed interupt endpoints). In this case, the code assumes
the bInterval is being reported in 1ms frames. As well, the correction
is only applied if the original bInterval value is out of the 1-16 range.
With this quirk applied to the device, the bInterval will be
accurately adjusted from microframes to an exponent.
Signed-off-by: James P Michels III <james.p.michels@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 20fbe3ae99.
As reported by Stephen Rothwell, it causes compile failures in certain
configurations:
drivers/net/usb/cdc_subset.c:360:15: error: 'dummy_prereset' undeclared here (not in a function)
.pre_reset = dummy_prereset,
^
drivers/net/usb/cdc_subset.c:361:16: error: 'dummy_postreset' undeclared here (not in a function)
.post_reset = dummy_postreset,
^
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: David Miller <davem@davemloft.net>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This device needs to be reset to recover from a timeout.
Unfortunately this can be handled only at the level of
the subdrivers.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTzTI9AAoJEIaOsuA1yqREIqcQAJbwMaDb5sp8dWst+nL1Vo8N
08bhOOM+o2KLiIBSNQh1hYtujpa06RSQMiNYZ7F/+R4Q3OAoq+uC0dD69TLEQ3Sd
1xi0UgUTAvtXo13TToRjIi0mYywrrkZ91Maqff5jZKdslOY4ZfAScpUQHyD3i1UO
JNUqpayYAnp8JJIGQ8CG1wAeJh/J8JH3O607vaknKVjds+WMkeC5ubnuV4sgVw71
8JTwxk22EkMTr2MKhHjZwcv016NMEvziinWVoTXcWN2Uwk42Dn1nhfaYWSvg7kZE
8/3t6zzdFMdoeeTEn2xXIQGTjbHW0sBS5+S+6PAon2YbjS3x40cbyLJnZ+KoVXog
iHDKAl5w53gd/7qMiv57dW+HRP0M7/m2iy/owIrY8H8DkM3uwFevaeq/G2raJKmA
frB1k95bSyypN7wVkALYv4nurP5+d7ERy9hPj/49M5giJXPpEIbgKN2qGdafaEx7
xzAI+GqYrFtmmg25+f6AQRicVczQNMCdDT8HPZ04099Z2JVY/4uOoqTl29CePMgo
OXeQ45ECMoJuRSwpF56e8h+qmsXp6WD31IhlcHseTvUvFu0Ex4SgUJhFP2UaF9WP
aOqz0w36yX/ME3VhQk9YImNqGoqEk6fYHIHhxfdDugt0n68+M56EiiwtKvd5v5BI
hCJAMBrv+WCGnJvWunVW
=aJY4
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.17 merge window
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
In preparation for DT conversion to reduce reliance on platform device
callbacks.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Introduce the module_usb_composite_driver macro as a convenience macro
for USB gadget composite driver modules, similar to module_usb_driver.
It is intended to be used by drivers which init/exit section does
nothing but calling usb_composite_probe/usb_composite_unrregister. By
using this macro it is possible to eliminate a few lines of boilerplate
code per USB gadget composite driver.
Based on f3a6a4b6 ("USB: Add helper macro for usb_driver boilerplate")
which introduced the according macro for USB drivers.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support for the PLX USB3380 and USB3382.
This driver is based on the driver from the manufacturer.
Since USB338X is register compatible with NET2280, I thought that it
would be better to include this hardware into net2280 driver.
Manufacturer's driver only supported the USB33X, did not follow the
Kernel Style and contain some trivial errors. This patch has tried to
address this issues.
This patch has only been tested on USB338x hardware, but the merge has
been done trying to not affect the behaviour of NET2280.
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
This reverts commit c4128cac35.
This should come through Felipe's tree first, and there was a bunch of
other patches that are needed after this one as well that I didn't have.
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the PLX USB3380 and USB3382.
This driver is based on the driver from the manufacturer.
Since USB338X is register compatible with NET2280, I thought that it
would be better to include this hardware into net2280 driver.
Manufacturer's driver only supported the USB33X, did not follow the
Kernel Style and contain some trivial errors. This patch has tried to
address this issues.
This patch has only been tested on USB338x hardware, but the merge has
been done trying to not affect the behaviour of NET2280.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The upper timer_interval limit is arbitrary and much higher
than anything usable in the real world. Reducing it from 15s
to ~4s to make the timer_interval fit in an u32 does not make
much difference. The limit is still outside the practical
bounds.
This eliminates the need for a 64bit timer_interval, fixing a
build error related to 64bit division:
drivers/built-in.o: In function `cdc_ncm_get_coalesce':
ak8975.c:(.text+0x1ac994): undefined reference to `__aeabi_uldivmod'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling netif_carrier_{on,off} is sufficient. There is no need
to duplicate the carrier state in a driver specific flag.
Acked-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of devices request much larger buffers than reasonable. This
cause real problems for users of hosts with limited resources.
Reducing the default buffer size to 16kB for such devices is
a reasonable trade-off between allowing them to aggregate traffic
and avoiding memory exhaustion on resource restrained hosts.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
To have an idea of the effects of the protocol coalescing
it's useful to have some counters showing the different
aspects.
Due to the asymmetrical usbnet interface the netdev
rx_bytes counter has been counting real received payload,
while the tx_bytes counter has included the NCM/MBIM
framing overhead. This overhead can be many times the
payload because of the aggressive padding strategy of
this driver, and will vary a lot depending on device
and traffic.
With very few exceptions, users are only interested in
the payload size. Having an somewhat accurate payload
byte counter is particularly important for mobile
broadband devices, which many NCM devices and of course
all MBIM devices are. Users and userspace applications
will use this counter to monitor account quotas.
Having protocol specific counters for the overhead, we are
now able to correct the tx_bytes netdev counter so that
it shows the real payload
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We pad frames larger than X to maximum size for devices which
don't need a ZLP after maximum sized frames. This allows the
device to optimize its transfers for one fixed buffer size.
X was arbitrarily set at 512 bytes regardless of real buffer
maximum, causing extreme overheads due to excessive padding of
larger tx buffers. Limit the padding to at most 3 full USB
packets, still allowing the overhead to payload ratio of 3/1.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many newer NCM and MBIM devices will request a maximum tx
datagram count which is much smaller than our hard-coded
absolute max. We can reduce the overhead without sacrificing
any of the simplicity for these devices, by simply using the
true negotiated count in when calculated the maximum NTH and
NDP header sizes.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Datagram coalescing is an integral part of the NCM and MBIM
protocols, intended to reduce the interrupt load primarily
on the device end of the USB link. As with all coalescing
solutions, there is a trade-off between buffering and
interrupts.
The current defaults are based on the assumption that device
side buffers should be the limiting factor. However, many
modern high speed LTE modems suffers from buffer-bloat,
making this assumption fail. This results in sub-optimal
performance due to excessive coalescing. And in cases where
such modems are connected to cheap embedded hosts there is
often severe buffer allocation issues, giving very noticeable
performance degradation .
A start on improving this is going from build time hard
coded limits to per device user configurable limits. The
ethtool coalescing API was selected as user interface
because, although the tuned values are buffer sizes, these
settings directly control datagram coalescing.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add handling of OS Extended Properties descriptors from configfs interface.
One kind of "OS Descriptors" are "Extended Properties" descriptors, which
need to be specified per interface or per group of interfaces described
by an IAD. This patch adds support for creating subdirectories
in interface.<n> directory located in the function's directory.
Names of subdirectories created become names of properties.
Each property contains two attributes: "type" and "data".
The type can be a numeric value 1..7 while data is a blob interpreted
depending on the type specified.
The types are:
1 - unicode string
2 - unicode string with environment variables
3 - binary
4 - little-endian 32-bit
5 - big-endian 32-bit
6 - unicode string with a symbolic link
7 - multiple unicode strings
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add handling of OS Extended Compatibility descriptors from configfs interface.
Hosts which expect the "OS Descriptors" ask only for configurations @ index 0,
but linux-based USB devices can provide more than one configuration.
This patch adds marking one of gadget's configurations the configuration
to be reported at index 0, regardless of the actual sequence of usb_add_config
invocations used for adding the configurations. The configuration is selected
by creating a symbolic link pointing to it from the "os_desc" directory
located at the top of a gadget's directory hierarchy.
One kind of "OS Descriptors" are "Extended Compatibility Descriptors",
which need to be specified per interface. This patch adds interface.<n>
directory in function's configfs directory to represent each interface
defined by the function. Each interface's directory contains two attributes:
"compatible_id" and "sub_compatible_id", which represent 8-byte
strings to be reported to the host as the "Compatible ID" and "Sub Compatible
ID".
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a custom (non-USB IF) extension to the USB standard:
http://msdn.microsoft.com/library/windows/hardware/gg463182
They grant permission to use the specification - there is
"Microsoft OS Descriptor Specification License Agreement"
under the link mentioned above, and its Section 2 "Grant
of License", letter (b) reads:
"Patent license. Microsoft hereby grants to You a nonexclusive,
royalty-free, nontransferable, worldwide license under Microsoft’s
patents embodied solely within the Specification and that are owned
or licensable by Microsoft to make, use, import, offer to sell,
sell and distribute directly or indirectly to Your Licensees Your
Implementation. You may sublicense this patent license to Your
Licensees under the same terms and conditions."
The said extension is maintained by Microsoft for Microsoft.
Yet it is fairly common for various devices to use it, and a
popular proprietary operating system expects devices to provide
"OS descriptors", so Linux-based USB gadgets whishing to be able
to talk to a variety of operating systems should be able to provide
the "OS descriptors".
This patch adds optional support for gadgets whishing to expose
the so called "OS Feature Descriptors", that is "Extended Compatibility ID"
and "Extended Properties".
Hosts which do request "OS descriptors" from gadgets do so during
the enumeration phase and before the configuration is set with
SET_CONFIGURATION. What is more, those hosts never ask for configurations
at indices other than 0. Therefore, gadgets whishing to provide
"OS descriptors" must designate one configuration to be used with
this kind of hosts - this is what os_desc_config is added for in
struct usb_composite_dev. There is an additional advantage to it:
if a gadget provides "OS descriptors" and designates one configuration
to be used with such non-USB-compliant hosts it can invoke
"usb_add_config" in any order because the designated configuration
will be reported to be at index 0 anyway.
This patch also adds handling vendor-specific requests addressed
at device or interface and related to handling "OS descriptors".
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a custom (non-USB IF) extension to the USB standard:
http://msdn.microsoft.com/library/windows/hardware/gg463182
They grant permission to use the specification - there is
"Microsoft OS Descriptor Specification License Agreement"
under the link mentioned above, and its Section 2 "Grant
of License", letter (b) reads:
"Patent license. Microsoft hereby grants to You a nonexclusive,
royalty-free, nontransferable, worldwide license under Microsoft’s
patents embodied solely within the Specification and that are owned
or licensable by Microsoft to make, use, import, offer to sell,
sell and distribute directly or indirectly to Your Licensees Your
Implementation. You may sublicense this patent license to Your
Licensees under the same terms and conditions."
The said extension is maintained by Microsoft for Microsoft.
Yet it is fairly common for various devices to use it, and a
popular proprietary operating system expects devices to provide
"OS descriptors", so Linux-based USB gadgets whishing to be able
to talk to a variety of operating systems should be able to provide
the "OS descriptors".
This patch adds optional support for gadgets whishing to expose
the so called "OS String" under index 0xEE of language 0.
The contents of the string is generated based on the qw_sign
array and b_vendor_code.
Interested gadgets need to set the cdev->use_os_string flag,
fill cdev->qw_sign with appropriate values and fill cdev->b_vendor_code
with a value of their choice.
This patch does not however implement responding to any vendor-specific
USB requests.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The NCM class match in the cdc_mbim driver is confusing and
cause unexpected behaviour. The USB core guarantees that a
USB interface is in altsetting 0 when probing starts. This
means that devices implementing a NCM 1.0 backwards
compatible MBIM function (a "NCM/MBIM function") always hit
the NCM entry in the cdc_mbim driver match table. Such
functions will never match any of the MBIM entries.
This causes unexpeced behaviour for cases where the NCM and
MBIM entries are differet, which is currently the case for
all except Ericsson devices.
Improve the probing of NCM/MBIM functions by looking up the
device again in the cdc_mbim match table after switching to
the MBIM identity.
The shared altsetting selection is updated to better
accommodate the new probing logic, returning the preferred
altsetting for the control interface instead of the data
interface. The control interface altsetting update is moved
to the cdc_mbim driver. It is never necessary to change the
control interface altsetting for NCM.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Reported by: Yu-an Shih <yshih@nvidia.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
New platform uses RBCPR hardware feature, with that voting for
absolute voltage of VDD CX is not required. Hence vote for corner of
VDD CX which uses nominal corner voltage on VDD CX.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Cc: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Select the secondary PHY using the TCSR register, if phy-num=1
in the DTS (or phy_number is set in the platform data). The
SOC has 2 PHYs which can be used with the OTG port, and this
code allows configuring the correct one.
Note: This resolves the problem I was seeing where I couldn't
get the USB driver working at all on a dragonboard, from cold
boot. This patch depends on patch 5/14 from Ivan's msm USB
patch set. It does not use DT for the register address, as
there's no evidence that this address changes between SoC
versions.
Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the value used for Parallel Transceiver Select (PTS) for the MSM USB
controller. This is a standard chipidea PORTSC definition, where
a PHY_TYPE of 10b (<<30) is ULPI and 11b (<<30) is SERIAL.
Fix the definitions and use them correctly in the driver code.
Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On few legacy platforms, USB PHY is having dedicated reset clk.
It is used to reset USB PHY after putting USB PHY into low power
mode and for calibration of USB PHY. Putting USB PHY into low
power mode is causing ulpi read/write timeout as expected. USB PHY
reset clk is not available on newer platform.
For 28nm PHY, reset USB PHY after resetting USB LINK.
Also reset USB PHY using USB_PHY_PON bit with USB_OTG_HS_PHY_CTRL
register after programming USB PHY Override registers as suggested
with hardware programming guidelines.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Cc: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allow support to use 2nd HSPHY with USB2 Core.
Some platforms may have configuration to allow USB controller
work with any of the two HSPHYs present. By default driver
configures USB core to use primary HSPHY. Add support to allow
user select 2nd HSPHY using DT parameter.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Cc: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using reset framework eliminate need of platform specific
callbacks and enable reset lines to be specified in DT files.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no references to 'pclk_src_name' in plaform code,
so it is unused.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use enum usb_dr_mode and drop default usb_dr_mode from platform data.
USB DT bindings states: dr_mode: "...In case this attribute isn't
passed via DT, USB DRD controllers should default to OTG...",
so remove redundand field.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Eliminating global variables allows driver to handle multiple
device instances.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
when checking if our generic PHY is enabled,
it's a lot easier to use IS_ENABLED() instead
of manually checking for it. While at that, also
remove the bogus defined(MODULE) at the end of
the line.
Signed-off-by: Felipe Balbi <balbi@ti.com>
it's now very easy to return a platform_device pointer
and have the caller pass it as argument when calling
usb_phy_generic_unregister().
Signed-off-by: Felipe Balbi <balbi@ti.com>
no functional changes, just renaming the function
in order to make it slightly clearer what it should
be used for, also matching the driver name.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull networking updates from David Miller:
"Here is my initial pull request for the networking subsystem during
this merge window:
1) Support for ESN in AH (RFC 4302) from Fan Du.
2) Add full kernel doc for ethtool command structures, from Ben
Hutchings.
3) Add BCM7xxx PHY driver, from Florian Fainelli.
4) Export computed TCP rate information in netlink socket dumps, from
Eric Dumazet.
5) Allow IPSEC SA to be dumped partially using a filter, from Nicolas
Dichtel.
6) Convert many drivers to pci_enable_msix_range(), from Alexander
Gordeev.
7) Record SKB timestamps more efficiently, from Eric Dumazet.
8) Switch to microsecond resolution for TCP round trip times, also
from Eric Dumazet.
9) Clean up and fix 6lowpan fragmentation handling by making use of
the existing inet_frag api for it's implementation.
10) Add TX grant mapping to xen-netback driver, from Zoltan Kiss.
11) Auto size SKB lengths when composing netlink messages based upon
past message sizes used, from Eric Dumazet.
12) qdisc dumps can take a long time, add a cond_resched(), From Eric
Dumazet.
13) Sanitize netpoll core and drivers wrt. SKB handling semantics.
Get rid of never-used-in-tree netpoll RX handling. From Eric W
Biederman.
14) Support inter-address-family and namespace changing in VTI tunnel
driver(s). From Steffen Klassert.
15) Add Altera TSE driver, from Vince Bridgers.
16) Optimizing csum_replace2() so that it doesn't adjust the checksum
by checksumming the entire header, from Eric Dumazet.
17) Expand BPF internal implementation for faster interpreting, more
direct translations into JIT'd code, and much cleaner uses of BPF
filtering in non-socket ocntexts. From Daniel Borkmann and Alexei
Starovoitov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1976 commits)
netpoll: Use skb_irq_freeable to make zap_completion_queue safe.
net: Add a test to see if a skb is freeable in irq context
qlcnic: Fix build failure due to undefined reference to `vxlan_get_rx_port'
net: ptp: move PTP classifier in its own file
net: sxgbe: make "core_ops" static
net: sxgbe: fix logical vs bitwise operation
net: sxgbe: sxgbe_mdio_register() frees the bus
Call efx_set_channels() before efx->type->dimension_resources()
xen-netback: disable rogue vif in kthread context
net/mlx4: Set proper build dependancy with vxlan
be2net: fix build dependency on VxLAN
mac802154: make csma/cca parameters per-wpan
mac802154: allow only one WPAN to be up at any given time
net: filter: minor: fix kdoc in __sk_run_filter
netlink: don't compare the nul-termination in nla_strcmp
can: c_can: Avoid led toggling for every packet.
can: c_can: Simplify TX interrupt cleanup
can: c_can: Store dlc private
can: c_can: Reduce register access
can: c_can: Make the code readable
...
Here's the big USB pull request for 3.15-rc1.
The normal set of patches, lots of controller driver updates, and a
smattering of individual USB driver updates as well.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7AbcACgkQMUfUDdst+ymbZACgncdbZyPsVZ7ZUpBFNbO/vBVT
T9UAmwciojEzjh7b+x4ylsWH+O3LWVN3
=RpAF
-----END PGP SIGNATURE-----
Merge tag 'usb-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big USB pull request for 3.15-rc1.
The normal set of patches, lots of controller driver updates, and a
smattering of individual USB driver updates as well.
All have been in linux-next for a while"
* tag 'usb-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (249 commits)
xhci: Transition maintainership to Mathias Nyman.
USB: disable reset-resume when USB_QUIRK_RESET is set
USB: unbind all interfaces before rebinding any
usb: phy: Add ulpi IDs for SMSC USB3320 and TI TUSB1210
usb: gadget: tcm_usb_gadget: stop format strings
usb: gadget: f_fs: add missing spinlock and mutex unlock
usb: gadget: composite: switch over to ERR_CAST()
usb: gadget: inode: switch over to memdup_user()
usb: gadget: f_subset: switch over to PTR_RET
usb: gadget: lpc32xx_udc: fix wrong clk_put() sequence
USB: keyspan: remove dead debugging code
USB: serial: add missing newlines to dev_<level> messages.
USB: serial: add missing braces
USB: serial: continue to write on errors
USB: serial: continue to read on errors
USB: serial: make bulk_out_size a lower limit
USB: cypress_m8: fix potential scheduling while atomic
devicetree: bindings: document lsi,zevio-usb
usb: chipidea: add support for USB OTG controller on LSI Zevio SoCs
usb: chipidea: imx: Use dev_name() for ci_hdrc name to distinguish USBs
...
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a race which happens by freeing an object on the stack.
Quoting Julius:
> The issue is
> that it calls usbnet_terminate_urbs() before that, which temporarily
> installs a waitqueue in dev->wait in order to be able to wait on the
> tasklet to run and finish up some queues. The waiting itself looks
> okay, but the access to 'dev->wait' is totally unprotected and can
> race arbitrarily. I think in this case usbnet_bh() managed to succeed
> it's dev->wait check just before usbnet_terminate_urbs() sets it back
> to NULL. The latter then finishes and the waitqueue_t structure on its
> stack gets overwritten by other functions halfway through the
> wake_up() call in usbnet_bh().
The fix is to just not allocate the data structure on the stack.
As dev->wait is abused as a flag it also takes a runtime PM change
to fix this bug.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Reported-by: Grant Grundler <grundler@google.com>
Tested-by: Grant Grundler <grundler@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
According to "Universal Serial Bus Communications Class Subclass
Specification for Mobile Broadband Interface Model, Revision 1.0,
Errata-1" published by USB-IF, the wMTU field of the MBIM extended
functional descriptor indicates the operator preferred MTU for IP data
streams.
This patch modifies cdc_ncm_setup to ensure that the MTU value set on
the usbnet device does not exceed the operator preferred MTU indicated
by wMTU if the MBIM device exposes a MBIM extended functional
descriptor.
Signed-off-by: Ben Chan <benchan@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a context modified revert of commit 6a9612e2cb
("net: cdc_ncm: remove ncm_parm field") which introduced
a NCM specification violation, causing setup errors for
some devices. These errors resulted in the device and
host disagreeing about shared settings, with complete
failure to communicate as the end result.
The NCM specification require that many of the NCM specific
control reuests are sent only while the NCM Data Interface
is in alternate setting 0. Reverting the commit ensures that
we follow this requirement.
Fixes: 6a9612e2cb ("net: cdc_ncm: remove ncm_parm field")
Reported-and-tested-by: Pasi Kärkkäinen <pasik@iki.fi>
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers are allowed to override the default bulk-out buffer size
(endpoint maximum packet size) in order to increase throughput, but it
does not make much sense to allow buffers smaller than the default.
Note that this is already how bulk_in_size is defined.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
and a multi-purpose PHY in APM, all adapted to generic PHY framework.
Adapted USB3 PHY driver in OMAP to generic PHY driver and also used
the same driver for SATA in OMAP. It also includes miscellaneous cleanups
and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJTHBXfAAoJEA5ceFyATYLZiq8P/jp8hqVxRXaJy6UUniggN2vX
JSdVgj6NPQijp9HAi5llb032coU4WYt7UFAAzOnIkzlQf+oIqu7e75DjGKCnV8sN
DlxsBTxptD949AGM3UVa1PnTHsJoIxq7HSV7rvpu2V2oH9vO4a2m7dGSHaGUpNei
ZH73oZtYrD+40eqv3TlUxw7aZpqTIvFvKD2HTJQab0jO06PT/mi7KC0TYXMnT+iK
GaZTiLkpocQGElz9CI5YzizjZY3zjK7yo9XOdiABx+NjNZ1sjLjc3eLRcqnL3NA0
0+oK/Gb/ZUuWrPDbUyB71VCi3OseOmNL3oAFIm+i1eV+8m56EKudyTn3jKyIpewG
Cv1si5t6dkyZELCUp2zi0tJqSiP+cTieO3UELXe2Hs6x0+ilHF6ElHEvgV9JcQHT
4ETtaN7ppkq35/D5SPxyW6Muqh+Pfxn4Duylp2HQXuqFFblFqIgSUtp1ZmSZIDzI
qYlVUgRVVZV7Qh+cgSR6YcU1j44os2RK+phlpTTInhun3UJDw/UeNluZhqPX3RRm
/luBWDuYRdn0h/4IPCS97ImeGBRkYJq5qMzm/JsYvBZBqq4deSOF9rgtwsHx4C5w
HFBqex3utumv/zNJtuNZ+dQce8olqrUkbPbp9eL8oNJbo5r7PQ1IhCWHTTQiuuiN
786aeMFxfMsfXVKztT4M
=mpZ3
-----END PGP SIGNATURE-----
Merge tag 'for_3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
Add new PHY drivers for SATA and USB in exynos, for USB in sunxi,
and a multi-purpose PHY in APM, all adapted to generic PHY framework.
Adapted USB3 PHY driver in OMAP to generic PHY driver and also used
the same driver for SATA in OMAP. It also includes miscellaneous cleanups
and fixes.
Rename struct omap_control_usb to struct omap_control_phy since it can
be used to control PHY of USB, SATA and PCIE. Also move the driver and
include files under *phy* and made the corresponding changes in the users
of phy-omap-control.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
another substantial pull request with new features all over
the place.
dwc3 got a bit closer towards hibernation support with after
a few patches re-factoring code to be reused for hibernation.
Also in dwc3 two new workarounds for known silicon bugs have
been implemented, some randconfig build errors have been fixed,
and it was taught about the new generic phy layer.
MUSB on AM335x now supports isochronous transfers thanks to
George Cherian's work.
The atmel_usba driver got two crash fixes: one when no endpoint
was specified in DeviceTree data and another when stopping the UDC
in DEBUG builds.
Function FS got a much needed fix to ffs_epfile_io() which was
copying too much data to userspace in some cases.
The printer gadget got a fix for a possible deadlock and plugged
a memory leak.
Ethernet drivers now use NAPI for RX which gives improved throughput.
Other than that, the usual miscelaneous fixes, cleanups, and
the like.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AAie
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.15
another substantial pull request with new features all over
the place.
dwc3 got a bit closer towards hibernation support with after
a few patches re-factoring code to be reused for hibernation.
Also in dwc3 two new workarounds for known silicon bugs have
been implemented, some randconfig build errors have been fixed,
and it was taught about the new generic phy layer.
MUSB on AM335x now supports isochronous transfers thanks to
George Cherian's work.
The atmel_usba driver got two crash fixes: one when no endpoint
was specified in DeviceTree data and another when stopping the UDC
in DEBUG builds.
Function FS got a much needed fix to ffs_epfile_io() which was
copying too much data to userspace in some cases.
The printer gadget got a fix for a possible deadlock and plugged
a memory leak.
Ethernet drivers now use NAPI for RX which gives improved throughput.
Other than that, the usual miscelaneous fixes, cleanups, and
the like.
Signed-of-by: Felipe Balbi <balbi@ti.com>
No functional change. Moved omap_usb.h from linux/usb/ to linux/phy/.
Also removed the unused members of struct omap_usb (after phy-omap-pipe3
started using it's own header file)
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This API is used to set wakeup enable at PHY registers, in that
case, the PHY can be waken up from suspend due to external events,
like vbus change, dp/dm change and id change.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On some older XHCIs streams are not supported and the UAS driver
will fail at probe time. For those devices storage should try
to bind to UAS devices.
This patch adds a flag for stream support to HCDs and evaluates
it.
[Note: Sarah fixed a bug where the USB 2.0 root hub, not USB 3.0 root
hub would get marked as being able to support streams.]
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The iu struct definitions are usb packet definitions, so no alignment should
happen. Notice that assuming 32 bit alignment this does not make any
difference at all.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The response iu struct before this patch has a size of 7 bytes (discounting
padding), which is weird since all other iu-s are explictly padded to
a multiple of 4 bytes.
More over submitting a 7 byte bulk transfer to the status endpoint when
expecting a response iu results in an USB babble error, as the device
actually sends 8 bytes.
Up on closer reading of the UAS spec:
http://www.t10.org/cgi-bin/ac.pl?t=f&f=uas2r00.pdf
The reason for this becomes clear, the 2 entries in "Table 17 — RESPONSE IU"
are numbered 4 and 6, looking at other iu definitions in the spec, esp.
multi-byte fields, this indicates that the ADDITIONAL RESPONSE INFORMATION
field is not a 2 byte field as one might assume at a first look, but is
a multi-byte field containing 3 bytes.
This also aligns with the SCSI Architecture Model 4 spec, which UAS is based
on which states in paragraph "7.1 Task management function procedure calls"
that the "Additional Response Information" output argument for a Task
management function procedure call is 3 bytes.
Last but not least I've verified this by sending a logical unit reset task
management call with an invalid lun to an actual uasp device, and received
back a response-iu with byte 6 being 0, and byte 7 being 9, which is the
responce code for an invalid iu, which confirms that the response code is
being reported in byte 7 of the response iu rather then in byte 6.
Things were working before despite this error in the response iu struct
definition because the additional response info field is normally filled
with zeros, and 0 is the response code value for success.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch makes it possible to set the chipidea udc into full-speed only mode.
It is set by the oftree property "maximum-speed = full-speed".
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix spelling typo in Documentation/DocBook.
It is because .html and .xml files are generated by make htmldocs,
I have to fix a typo within the source files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree.
The largest part of this is a conversion of device registration for some
renesas shmobile/sh devices over to use resources. This has required
coordination with the corresponding arch/sh changes, and we've agreed
to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure firmware,
which is what is used on many of the commercial Nvidia Tegra products
that are in the market, including the Nvidia Shield. The code is local
to arch/arm at this time since it's uncertain whether it will be shared
with arm64 longer-term, if needed we will refactor later.
A couple of new RTC drivers used on ARM boards, merged through our tree
on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JJlw
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement special hw_write
and hw_test_and_clear for imx28.
Discussion for it at below:
http://marc.info/?l=linux-usb&m=137996395529294&w=2
This patch is needed for stable tree 3.11+.
Cc: stable@vger.kernel.org
Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* qcom/drivers:
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch fix compilation error when driver is compiled
in multi-platform builds.
drivers/built-in.o: In function `msm_otg_link_clk_reset':
./drivers/usb/phy/phy-msm-usb.c:314: undefined reference to `clk_reset'
./drivers/usb/phy/phy-msm-usb.c:318: undefined reference to `clk_reset'
Use platform data supplied reset handlers and adjust error
messages reported when reset sequence fail.
This is an intermediate step before adding support for reset
framework and newer targets.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This pull request is quite extensive, containing
105 non-merge commits. Because of that, we describe
the changes in sections below:
New drivers:
- Keystone PHY driver and DWC3 Glue Layer
- Aeroflex Gaisler GRUSBDC
- Tahvo PHY driver for N770
- JZ4740 MUSB gluer Layer
- Broadcom PHY Driver
Important new features:
- MUSB DSPS learned about suspend/resume
- New quirk_ep_out_aligned_size flag added to struct usb_gadget
- DWC3 initializes the new quirk flag so gadget drivers can use it.
- AM335x PHY Driver learns about remote wakeup
- Renesas USBHS now requests DMA Engine only once
- s3c-hsotg is now re-used on Broadcom devices
- USB PHY layer now makes sure to initialize the notifier for all
drivers
- omap-control learned about TI's new AM437x devices
- few other usb gadget/function drivers learned about the new
configfs-based binding.
Misc Fixes and Clean Ups:
- Several sparse fixes all over the place
- Removal of redundant of_match_ptr()
- r-car gen2 phy now uses usb_add_phy_dev()
- removal of DEFINE_PCI_DEVICE_TABLE() from a few drivers
- conversion to clk_prepare/clk_unprepare on r8a66597-udc
- some randconfig errors and build warnings were fixed
- removal of unnecessary lock on dwc3-omap.c
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=N4//
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v3.14 merge window
This pull request is quite extensive, containing
105 non-merge commits. Because of that, we describe
the changes in sections below:
New drivers:
- Keystone PHY driver and DWC3 Glue Layer
- Aeroflex Gaisler GRUSBDC
- Tahvo PHY driver for N770
- JZ4740 MUSB gluer Layer
- Broadcom PHY Driver
Important new features:
- MUSB DSPS learned about suspend/resume
- New quirk_ep_out_aligned_size flag added to struct usb_gadget
- DWC3 initializes the new quirk flag so gadget drivers can use it.
- AM335x PHY Driver learns about remote wakeup
- Renesas USBHS now requests DMA Engine only once
- s3c-hsotg is now re-used on Broadcom devices
- USB PHY layer now makes sure to initialize the notifier for all
drivers
- omap-control learned about TI's new AM437x devices
- few other usb gadget/function drivers learned about the new
configfs-based binding.
Misc Fixes and Clean Ups:
- Several sparse fixes all over the place
- Removal of redundant of_match_ptr()
- r-car gen2 phy now uses usb_add_phy_dev()
- removal of DEFINE_PCI_DEVICE_TABLE() from a few drivers
- conversion to clk_prepare/clk_unprepare on r8a66597-udc
- some randconfig errors and build warnings were fixed
- removal of unnecessary lock on dwc3-omap.c
Signed-of-by: Felipe Balbi <balbi@ti.com>
This adds omap control module support for USBSS in AM437x SoC.
Update DT binding information to reflect these changes.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSrhGrAAoJEHm+PkMAQRiGsNoH/jIK3CsQ2lbW7yRLXmfgtbzz
i2Kep6D4SDvmaLpLYOVC8xNYTiE8jtTbSXHomwP5wMZ63MQDhBfnEWsEWqeZ9+D9
3Q46p0QWuoBgYu2VGkoxTfygkT6hhSpwWIi3SeImbY4fg57OHiUil/+YGhORM4Qc
K4549OCTY3sIrgmWL77gzqjRUo+pQ4C73NKqZ3+5nlOmYBZC1yugk8mFwEpQkwhK
4NRNU760Fo+XIht/bINqRiPMddzC15p0mxvJy3cDW8bZa1tFSS9SB7AQUULBbcHL
+2dFlFOEb5SV1sNiNPrJ0W+h2qUh2e7kPB0F8epaBppgbwVdyQoC2u4uuLV2ZN0=
=lI2r
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc4' into next
Linux 3.13-rc4
* tag 'v3.13-rc4': (1001 commits)
Linux 3.13-rc4
null_blk: mem garbage on NUMA systems during init
radeon_pm: fix oops in hwmon_attributes_visible() and radeon_hwmon_show_temp_thresh()
Revert "selinux: consider filesystem subtype in policies"
igb: Fix for issue where values could be too high for udelay function.
i40e: fix null dereference
ARM: fix asm/memory.h build error
dm array: fix a reference counting bug in shadow_ablock
dm space map: disallow decrementing a reference count below zero
mm: memcg: do not allow task about to OOM kill to bypass the limit
mm: memcg: fix race condition between memcg teardown and swapin
thp: move preallocated PTE page table on move_huge_pmd()
mfd/rtc: s5m: fix register updating by adding regmap for RTC
rtc: s5m: enable IRQ wake during suspend
rtc: s5m: limit endless loop waiting for register update
rtc: s5m: fix unsuccesful IRQ request during probe
drivers/rtc/rtc-s5m.c: fix info->rtc assignment
include/linux/kernel.h: make might_fault() a nop for !MMU
drivers/rtc/rtc-at91rm9200.c: correct alarm over day/month wrap
procfs: also fix proc_reg_get_unmapped_area() for !MMU case
...
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds "maxpacket_limit" to struct usb_ep. This field contains
maximum value of maxpacket supported by driver, and is set in driver probe.
This value should be used by autoconfig() function, because value of field
"maxpacket" is set to value from endpoint descriptor when endpoint becomes
enabled. So when autoconfig() function will be called again for this endpoint,
"maxpacket" value will contain wMaxPacketSize from descriptior instead of
maximum packet size for this endpoint.
For this reason this patch adds new field "maxpacket_limit" which contains
value of maximum packet size (which defines maximum endpoint capabilities).
This value is used in ep_matches() function used by autoconfig().
Value of "maxpacket_limit" should be set in UDC driver probe function, using
usb_ep_set_maxpacket_limit() function, defined in gadget.h. This function
set choosen value to both "maxpacket_limit" and "maxpacket" fields.
This patch modifies UDC drivers by adding support for maxpacket_limit.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no old function interface users left, so the old interface can
be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is required in order to integrate configfs support.
f_fs needs to be a separately compiled module and so it needs to use the new
interface.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This will be required in order to use the new function interface
(usb_get_function_instance/usb_put_function_instance)
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyunmgin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB function's configfs config group is created in a generic way in
usb/gadget/configfs.c:function_make(), which in turn delegates actual
allocation and setup of the USB function instance to a particular
implementation, e.g. in f_acm.c. The said implementation does its job
in a parameter-less function e.g. acm_alloc_instance(), which results
in creating an unnamed config group, whose name is set later in
function_make(). function_make() creates the name by parsing a string
of the form:
<function name>.<instance name>
which comes from userspace as a parameter to mkdir invocation.
Up to now only <function name> has been used, while <instance name>
has been ignored. This patch adds a set_inst_name() operation to
struct usb_function_instance which allows passing the <instance name>
from function_make() so that it is not ignored. It is entirely up to the
implementor of set_inst_name() what to do with the <instance name>.
In a typical case, the struct usb_function_instance is embedded in a
larger struct which is retrieved in set_inst_name() with container_of(),
and the larger struct contains a field to store the <instance name>.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Change the default enumeration scheme for xhci attached non-SuperSpeed
devices from:
Reset
SetAddress [xhci address-device BSR = 0]
GetDescriptor(8)
GetDescriptor(18)
...to:
Reset
[xhci address-device BSR = 1]
GetDescriptor(64)
Reset
SetAddress [xhci address-device BSR = 0]
GetDescriptor(18)
...as some devices misbehave when encountering a SetAddress command
prior to GetDescriptor. There are known legacy devices that require
this scheme, but testing has found at least one USB3 device that fails
enumeration when presented with this ordering. For now, follow the ehci
case and enable 'new scheme' by default for non-SuperSpeed devices.
To support this enumeration scheme on xhci the AddressDevice operation
needs to be performed twice. The first instance of the command enables
the HC's device and slot context info for the device, but omits sending
the device a SetAddress command (BSR == block set address request).
Then, after GetDescriptor completes, follow up with the full
AddressDevice+SetAddress operation.
As mentioned before, this ordering of events with USB3 devices causes an
extra state transition to be exposed to xhci. Previously USB3 devices
would transition directly from 'enabled' to 'addressed' and never need
to underrun responses to 'get descriptor'. We do see the 64-byte
descriptor fetch the correct data, but the following 18-byte descriptor
read after the reset gets:
bLength = 0
bDescriptorType = 0
bcdUSB = 0
bDeviceClass = 0
bDeviceSubClass = 0
bDeviceProtocol = 0
bMaxPacketSize0 = 9
instead of:
bLength = 12
bDescriptorType = 1
bcdUSB = 300
bDeviceClass = 0
bDeviceSubClass = 0
bDeviceProtocol = 0
bMaxPacketSize0 = 9
which results in the discovery process looping until falling back to
'old scheme' enumeration.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: David Moore <david.moore@gmail.com>
Suggested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Due to USB controllers may have different restrictions, usb gadget layer
needs to provide a generic way to inform gadget functions to complain
with non-standard requirements.
This patch adds 'quirk_ep_out_aligned_size' field to struct usb_gadget
to inform when controller's epout requires buffer size to be aligned to
MaxPacketSize. A helper is also provided to align buffer size when
necessary.
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves all bitflags to the end of usb_gadget struct in order
to improve readability.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This adds remove_phy flag to the HCD structure. If the flag is
set and if hcd->phy is valid, the phy is shutdown and released
whenever usb_add_hcd fails or usb_hcd_remove is called.
This can be used by the HCD drivers to auto-remove
the external USB phy when it is no longer needed.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When multiple wireless USB devices are connected and one of the devices
disconnects, the host will distribute a new group key to the remaining
devicese using wusbhc_gtk_rekey. wusbhc_gtk_rekey takes the
wusbhc->mutex and holds it while it submits a URB to set the new key.
This causes a deadlock in wa_urb_enqueue when it calls a device lookup
helper function that takes the same lock.
This patch changes wusbhc_gtk_rekey to submit a work item to set the GTK
so that the URB is submitted without holding wusbhc->mutex.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Other USB drivers may want to use OTG final state machine
implementation, so make this header available for them.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dsps platform needs to save save some registers at suspend time and
restore them after resume. This patch adds a struct for these registers,
and also lets the musb core know that the core registers need to be
saved as well.
We also have to explicitly de-assert the port reset upon resume on this
platform, but musb_port_reset() should not be called from glue layers.
Hence, introduce a flag in struct musb_hdrc_config for this.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull networking updates from David Miller:
1) The addition of nftables. No longer will we need protocol aware
firewall filtering modules, it can all live in userspace.
At the core of nftables is a, for lack of a better term, virtual
machine that executes byte codes to inspect packet or metadata
(arriving interface index, etc.) and make verdict decisions.
Besides support for loading packet contents and comparing them, the
interpreter supports lookups in various datastructures as
fundamental operations. For example sets are supports, and
therefore one could create a set of whitelist IP address entries
which have ACCEPT verdicts attached to them, and use the appropriate
byte codes to do such lookups.
Since the interpreted code is composed in userspace, userspace can
do things like optimize things before giving it to the kernel.
Another major improvement is the capability of atomically updating
portions of the ruleset. In the existing netfilter implementation,
one has to update the entire rule set in order to make a change and
this is very expensive.
Userspace tools exist to create nftables rules using existing
netfilter rule sets, but both kernel implementations will need to
co-exist for quite some time as we transition from the old to the
new stuff.
Kudos to Patrick McHardy, Pablo Neira Ayuso, and others who have
worked so hard on this.
2) Daniel Borkmann and Hannes Frederic Sowa made several improvements
to our pseudo-random number generator, mostly used for things like
UDP port randomization and netfitler, amongst other things.
In particular the taus88 generater is updated to taus113, and test
cases are added.
3) Support 64-bit rates in HTB and TBF schedulers, from Eric Dumazet
and Yang Yingliang.
4) Add support for new 577xx tigon3 chips to tg3 driver, from Nithin
Sujir.
5) Fix two fatal flaws in TCP dynamic right sizing, from Eric Dumazet,
Neal Cardwell, and Yuchung Cheng.
6) Allow IP_TOS and IP_TTL to be specified in sendmsg() ancillary
control message data, much like other socket option attributes.
From Francesco Fusco.
7) Allow applications to specify a cap on the rate computed
automatically by the kernel for pacing flows, via a new
SO_MAX_PACING_RATE socket option. From Eric Dumazet.
8) Make the initial autotuned send buffer sizing in TCP more closely
reflect actual needs, from Eric Dumazet.
9) Currently early socket demux only happens for TCP sockets, but we
can do it for connected UDP sockets too. Implementation from Shawn
Bohrer.
10) Refactor inet socket demux with the goal of improving hash demux
performance for listening sockets. With the main goals being able
to use RCU lookups on even request sockets, and eliminating the
listening lock contention. From Eric Dumazet.
11) The bonding layer has many demuxes in it's fast path, and an RCU
conversion was started back in 3.11, several changes here extend the
RCU usage to even more locations. From Ding Tianhong and Wang
Yufen, based upon suggestions by Nikolay Aleksandrov and Veaceslav
Falico.
12) Allow stackability of segmentation offloads to, in particular, allow
segmentation offloading over tunnels. From Eric Dumazet.
13) Significantly improve the handling of secret keys we input into the
various hash functions in the inet hashtables, TCP fast open, as
well as syncookies. From Hannes Frederic Sowa. The key fundamental
operation is "net_get_random_once()" which uses static keys.
Hannes even extended this to ipv4/ipv6 fragmentation handling and
our generic flow dissector.
14) The generic driver layer takes care now to set the driver data to
NULL on device removal, so it's no longer necessary for drivers to
explicitly set it to NULL any more. Many drivers have been cleaned
up in this way, from Jingoo Han.
15) Add a BPF based packet scheduler classifier, from Daniel Borkmann.
16) Improve CRC32 interfaces and generic SKB checksum iterators so that
SCTP's checksumming can more cleanly be handled. Also from Daniel
Borkmann.
17) Add a new PMTU discovery mode, IP_PMTUDISC_INTERFACE, which forces
using the interface MTU value. This helps avoid PMTU attacks,
particularly on DNS servers. From Hannes Frederic Sowa.
18) Use generic XPS for transmit queue steering rather than internal
(re-)implementation in virtio-net. From Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
random32: add test cases for taus113 implementation
random32: upgrade taus88 generator to taus113 from errata paper
random32: move rnd_state to linux/random.h
random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized
random32: add periodic reseeding
random32: fix off-by-one in seeding requirement
PHY: Add RTL8201CP phy_driver to realtek
xtsonic: add missing platform_set_drvdata() in xtsonic_probe()
macmace: add missing platform_set_drvdata() in mace_probe()
ethernet/arc/arc_emac: add missing platform_set_drvdata() in arc_emac_probe()
ipv6: protect for_each_sk_fl_rcu in mem_check with rcu_read_lock_bh
vlan: Implement vlan_dev_get_egress_qos_mask as an inline.
ixgbe: add warning when max_vfs is out of range.
igb: Update link modes display in ethtool
netfilter: push reasm skb through instead of original frag skbs
ip6_output: fragment outgoing reassembled skb properly
MAINTAINERS: mv643xx_eth: take over maintainership from Lennart
net_sched: tbf: support of 64bit rates
ixgbe: deleting dfwd stations out of order can cause null ptr deref
ixgbe: fix build err, num_rx_queues is only available with CONFIG_RPS
...
Some drivers implementing NCM-like protocols, may re-use those functions, as is
the case in the huawei_cdc_ncm driver.
Export them via EXPORT_SYMBOL_GPL, in accordance with how other functions have
been exported.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
header_desc was completely unused and union_desc was never used
outside cdc_ncm_bind_common.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving the call to cdc_ncm_setup() after the endpoint
setup removes the last remaining reference to ncm_parm
outside cdc_ncm_setup.
Collecting all the ncm_parm based calculations in
cdc_ncm_setup improves readability.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
These fields are only used to prevent printing the same speeds
multiple times if we receive multiple identical speed notifications.
The value of these printk's is questionable, and even more so when
we filter out some of the notifications sent us by the firmware. If
we are going to print any of these, then we should print them all.
Removing little used fields is a bonus.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already use the usbnet udev field everywhere this could have
been used.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Too many pointers back and forth are likely to confuse developers,
creating subtle bugs whenever we forget to syncronize them all.
As a usbnet driver, we should stick with the standard struct
usbnet fields as much as possible. The netdevice is one such
field.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to duplicate stuff already in the common usbnet
struct. We still need to keep our special find_endpoints
function because we need explicit control over the selected
altsetting.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is always a duplicate of the "control" field. It causes
confusion wrt intf_data updates and cleanups.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes it a lot easier to test modified versions
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJSZRSSAAoJEIaOsuA1yqRE6EAP/AuF0dWV3wNSuv5h3ZPOybu8
uULX0E/VA2aGs8/55FeuQIJAn499zdt0KH5l8P3CGrKBPk8BN/rD55a6uwYEfWO8
wwTJpVeRyRQS8jes22vPqA22TXgl88SJO0RrsCarrzOcMNloVtOA4zyorITuGZQB
jEKmf9BdjIUlzZkH9t33v3O8kB5pJ1YvBQGRWXbBZvxSzohPC2LYerZKMPN99hDB
2YnJXVKZqZzKbcQQmJklWqRo0RTprWz0Mqcu2r8Lnnn2ZqnT3RBmCBsYXefsp4nF
egRJy51DiypEYt3/OEBf21BySjZHjO6+9jfzOmuOGoEiqw6XCRFMydVpqJJHC8WX
MoCs31VnGwwwBpSOz9ECS9QYXne9jx/bJ6iKoS736sgA20ZA6wBbEDhJlTckcZtm
TEC+UTKevNACAP8cjhGEquqwt5H/rMaYFMXEYQj+gvO2jDsNUGWb74l5VDaBiIm7
GzdUmgmYym8HKT80tgEcgvsUoUphDeNE84OW/jo1nFUDvCniLfQBAYZooEnTHY2H
AW+DqimJzNnKcHo4w/HUQhRgK9147aRbskmVIbepIIW7WQdFQBOPVy7BbfnVD2vA
j01JPshgtnjb+MZb6VqnbcaWKPnJr3KTnOpTTMyk5pKnBOf6PHb1S1Tq5uqtW2Ki
gqi/SXZJ1bYDVaaspNWr
=LDY7
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.13
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Do not overwrite the multi-byte fields of usb_wa_descriptor with their
cpu format values after reading the descriptor. Leave the values as
__le16 and swap on use. This is more consistent with other uses of USB
descriptors.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3fa4d734 (usb: phy: rename nop_usb_xceiv => usb_phy_gen_xceiv)
changed the conditional around the declaration of usb_nop_xceiv_register
from
#if defined(CONFIG_NOP_USB_XCEIV) ||
(defined(CONFIG_NOP_USB_XCEIV_MODULE) && defined(MODULE))
to
#if IS_ENABLED(CONFIG_NOP_USB_XCEIV)
While that looks the same, it is semantically different. The first expression
is true if CONFIG_NOP_USB_XCEIV is built as module and if the including
code is built as module. The second expression is true if code depending on
CONFIG_NOP_USB_XCEIV if built as module or into the kernel.
As a result, the arm:allmodconfig build fails with
arch/arm/mach-omap2/built-in.o: In function `omap3_evm_init':
arch/arm/mach-omap2/board-omap3evm.c:703: undefined reference to
`usb_nop_xceiv_register'
Fix the problem by reverting to the old conditional.
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Export usb_serial_generic_write_start which is needed when implementing
a custom resume function while still relying on the generic write
implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For improved scheduling of transfers through a Transaction Translator,
ehci-hcd will need to store a bunch of information associated with the
FS/LS bus on the downstream side of the TT. This patch adds a pointer
for such HCD-private data to the usb_tt structure.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Host controller drivers use the NS_TO_US macro to convert transaction
times, which are computed in nanoseconds, to microseconds for
scheduling. Periodic scheduling requires worst-case estimates, but
the macro does its conversion using round-to-nearest. This patch
changes it to use round-up, giving a correct worst-case value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO number of the RESET line can be passed to the
driver using the gpio_reset member.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This function was preventing us from supporting multiple
instances. Get rid of it. Since we support DT boots only,
users can get the control device phandle from the DT node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omap_get_control_dev() is being deprecated as it doesn't support
multiple instances. As control device is present only from OMAP4
onwards which supports DT only, we use phandles to get the
reference to the control device.
Also get rid of "ti,has-mailbox" property as it is redundant and
we can determine that from whether "ctrl-module" property is present
or not. Get rid of has_mailbox from musb_hdrc_platform_data as well.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for new device types and in the process rid of "ti,type"
device tree property. The correct type of device will be determined
from the compatible string instead.
Introduce a compatible string for each device type. At the moment
we support 4 types OTGHS, USB2, PIPE3 (e.g. USB3) and DRA7USB2.
Update DT binding information to reflect these changes.
Also get rid of omap_control_usb3_phy_power(). Just one function
i.e. omap_control_usb_phy_power() will now take care of all PHY types.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omap-control device is present from OMAP4 onwards which
support device tree boots only. So get rid of platform data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds transfer type enum and packet definitions for
WA_XFER_ISO_PACKET_INFO and WA_XFER_ISO_PACKET_STATUS packets.
It also changes instances of __attribute__((packed)) to __packed to make
checkpatch.pl happy.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 638c5115a7949(USBNET: support DMA SG) introduces DMA SG
if the usb host controller is capable of building packet from
discontinuous buffers, but missed handling padding packet when
building DMA SG.
This patch attachs the pre-allocated padding packet at the
end of the sg list, so padding packet can be sent to device
if drivers require that.
Reported-by: David Laight <David.Laight@aculab.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch is required to resolve remote wake issues with
certain devices.
Issue description:
If the remote wake is issued from the device in a specific timing
condition while the system is entering sleep state then it may cause
system to auto wake on subsequent sleep cycle.
Root cause:
Host controller rebroadcasts the Resume signal > 100 µseconds after
receiving the original resume event from the device. For proper
function, some devices may require the rebroadcast of resume event
within the USB spec of 100µS.
Workaroud:
1. Filter the AMD platforms with Yangtze chipset, then judge of all the usb
devices are mouse or not. And get out the port id which attached a mouse
with Pixart controller.
2. Then reset the port which attached issue device during system resume
from S3.
[Q] Why the special devices are only mice? Would high speed devices
such as 3G modem or USB Bluetooth adapter trigger this issue?
- Current this sensitivity is only confined to devices that use Pixart
controllers. This controller is designed for use with LS mouse
devices only. We have not observed any other devices failing. There
may be a small risk for other devices also but this patch (reset
device in resume phase) will cover the cases if required.
[Q] Shouldn’t the resume signal be sent within 100 us for every
device?
- The Host controller may not send the resume signal within 100us,
this our host controller specification change. This is why we
require the patch to prevent side effects on certain known devices.
[Q] Why would clicking mouse INTENSELY to wake the system up trigger
this issue?
- This behavior is specific to the devices that use Pixart controller.
It is timing dependent on when the resume event is triggered during
the sleep state.
[Q] Is it a host controller issue or mouse?
- It is the host controller behavior during resume that triggers the
device incorrect behavior on the next resume.
This patch sets USB_QUIRK_RESET_RESUME flag for these Pixart-based mice
when they attached to platforms with AMD Yangtze chipset.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that URBs can be completed inside tasklets, we need a way of
determining whether a completion handler for a given endpoint is
currently running. Otherwise it's not possible to maintain the API
guarantee about keeping isochronous streams synchronous when an
underrun occurs.
This patch adds a field and a routine to check whether a completion
handler for a periodic endpoint is running. At the moment no
analogous routine appears to be necessary for async endpoints, but one
can always be added.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
Here is the big char/misc driver pull request for 3.12-rc1
Lots of driver updates all over the char/misc tree, full details in the
shortlog below.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlH58ACgkQMUfUDdst+ymTGwCdH1BmMdypyjUBxJEoWNDUuwXn
/AQAoKt329vmB6qn41rvaTilHHYUXS7H
=ovaW
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc patches from Greg KH:
"Here is the big char/misc driver pull request for 3.12-rc1
Lots of driver updates all over the char/misc tree, full details in
the shortlog"
* tag 'char-misc-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (62 commits)
drivers: uio: Kconfig: add MMU dependancy for UIO
drivers: uio: Add driver for Humusoft MF624 DAQ PCI card
drivers: uio_pdrv_genirq: use dev_get_platdata()
drivers: uio_pruss: use dev_get_platdata()
drivers: uio_dmem_genirq: use dev_get_platdata()
drivers: parport: Kconfig: exclude h8300 for PARPORT_PC
drivers: misc: ti-st: fix potential race if st_kim_start fails
Drivers: hv: vmbus: Do not attempt to negoatiate a new version prematurely
misc: vmw_balloon: Remove braces to fix build for clang.
Drivers: hv: vmbus: Fix a bug in the handling of channel offers
vme: vme_ca91cx42.c: fix to pass correct device identity to free_irq()
VMCI: Add support for virtual IOMMU
VMCI: Remove non-blocking/pinned queuepair support
uio: uio_pruss: remove unnecessary platform_set_drvdata()
parport: amiga: remove unnecessary platform_set_drvdata()
vme: vme_vmivme7805.c: add missing __iomem annotation
vme: vme_ca91cx42.c: add missing __iomem annotation
vme: vme_tsi148.c: add missing __iomem annotation
drivers/misc/hpilo: Correct panic when an AUX iLO is detected
uio: drop unused vma_count member in uio_device struct
...
This patch fixes a build error that occurs when CONFIG_PM is enabled
and CONFIG_PM_SLEEP isn't:
>> drivers/usb/host/ohci-pci.c:294:10: error: 'usb_hcd_pci_pm_ops' undeclared here (not in a function)
.pm = &usb_hcd_pci_pm_ops
Since the usb_hcd_pci_pm_ops structure is defined and used when
CONFIG_PM is enabled, its declaration should not be protected by
CONFIG_PM_SLEEP.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the HWA encounters a STALL on a control endpoint, it should clear the
RPIPE_STALL feature on the RPIPE before processing the next transfer
request. Otherwise, all transfer requests on that endpoint after the
first STALL will fail because the RPIPE is still in the halted state.
This also removes the unneccessary call to spin_lock_irqsave for a nested
lock that was present in the first patch.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the controller only runs when the ci->vbus_active is true.
So the flag CI_HDRC_PULLUP_ON_VBUS is useless no longer.
If the user doesn't have otgsc, he/she needs to change ci_handle_vbus_change
to update ci->vbus_active.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we need otgsc to know vbus's status at some chipidea
controllers even it is peripheral-only mode. Besides, some
SoCs (eg, AR9331 SoC) don't have otgsc register even
the DCCPARAMS_DC and DCCPARAMS_HC are both 1 at CAP_DCCPARAMS.
We inroduce flag CI_HDRC_DUAL_ROLE_NOT_OTG to indicate if the
controller is dual role, but not supports OTG. If this flag is
not set, we follow the rule that if DCCPARAMS_DC and DCCPARAMS_HC
are both 1 at CAP_DCCPARAMS, then this controller is otg capable.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vbus regulator is a common element for USB vbus operation,
So, move it from glue layer to core.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All patches here have been pending on linux-usb
and sitting in linux-next for a while now.
The biggest things in this tag are:
DWC3 learned proper usage of threaded IRQ
handlers and now we spend very little time
in hardirq context.
MUSB now has proper support for BeagleBone and
Beaglebone Black.
Tegra's USB support also got quite a bit of love
and is learning to use PHY layer and generic DT
attributes.
Other than that, the usual pack of cleanups and
non-critical fixes follow.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=3NS9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.12 merge window
All patches here have been pending on linux-usb
and sitting in linux-next for a while now.
The biggest things in this tag are:
DWC3 learned proper usage of threaded IRQ
handlers and now we spend very little time
in hardirq context.
MUSB now has proper support for BeagleBone and
Beaglebone Black.
Tegra's USB support also got quite a bit of love
and is learning to use PHY layer and generic DT
attributes.
Other than that, the usual pack of cleanups and
non-critical fixes follow.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/gadget/udc-core.c
drivers/usb/host/ehci-tegra.c
drivers/usb/musb/omap2430.c
drivers/usb/musb/tusb6010.c
This patch introduces support of DMA SG if the USB host controller
which usbnet device is attached to is capable of building packet from
discontinuous buffers.
The patch supports passing the skb fragment buffers to usb stack directly
via urb->sg.
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Grant Grundler <grundler@google.com>
Cc: Freddy Xin <freddy@asix.com.tw>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch implements the mechanism of giveback of URB in
tasklet context, so that hardware interrupt handling time for
usb host controller can be saved much, and HCD interrupt handling
can be simplified.
Motivations:
1), on some arch(such as ARM), DMA mapping/unmapping is a bit
time-consuming, for example: when accessing usb mass storage
via EHCI on pandaboard, the common length of transfer buffer is 120KB,
the time consumed on DMA unmapping may reach hundreds of microseconds;
even on A15 based box, the time is still about scores of microseconds
2), on some arch, reading DMA coherent memoery is very time-consuming,
the most common example is usb video class driver[1]
3), driver's complete() callback may do much things which is driver
specific, so the time is consumed unnecessarily in hardware irq context.
4), running driver's complete() callback in hardware irq context causes
that host controller driver has to release its lock in interrupt handler,
so reacquiring the lock after return may busy wait a while and increase
interrupt handling time. More seriously, releasing the HCD lock makes
HCD becoming quite complicated to deal with introduced races.
So the patch proposes to run giveback of URB in tasklet context, then
time consumed in HCD irq handling doesn't depend on drivers' complete and
DMA mapping/unmapping any more, also we can simplify HCD since the HCD
lock isn't needed to be released during irq handling.
The patch should be reasonable and doable:
1), for drivers, they don't care if the complete() is called in hard irq
context or softirq context
2), the biggest change is the situation in which usb_submit_urb() is called
in complete() callback, so the introduced tasklet schedule delay might be a
con, but it shouldn't be a big deal:
- control/bulk asynchronous transfer isn't sensitive to schedule
delay
- the patch schedules giveback of periodic URBs using
tasklet_hi_schedule, so the introduced delay should be very
small
- for ISOC transfer, generally, drivers submit several URBs
concurrently to avoid interrupt delay, so it is OK with the
little schedule delay.
- for interrupt transfer, generally, drivers only submit one URB
at the same time, but interrupt transfer is often used in event
report, polling, ... situations, and a little delay should be OK.
Considered that HCDs may optimize on submitting URB in complete(), the
patch may cause the optimization not working, so introduces one flag to mark
if the HCD supports to run giveback URB in tasklet context. When all HCDs
are ready, the flag can be removed.
[1], http://marc.info/?t=136438111600010&r=1&w=2
Cc: Oliver Neukum <oliver@neukum.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra30 TRM recommends configuration of certain PHY parameters for
optimal quality. Program the following registers based on device tree
parameters:
- UTMIP_XCVR_HSSLEW: HS slew rate control.
- UTMIP_HSSQUELCH_LEVEL: HS squelch detector level
- UTMIP_HSDISCON_LEVEL: HS disconnect detector level.
These registers exist in Tegra20, but programming them hasn't been
necessary, so these parameters won't be set on Tegra20 to keep the
device trees backward compatible.
Additionally, the UTMIP_XCVR_SETUP parameter can be set from fuses
instead of a software-programmed value, as the optimal value can
vary between invidual boards. The boolean property
nvidia,xcvr-setup-use-fuses can be used to enable this behaviour.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Tegra30 USB PHY is a bit different than the Tegra20 PHY:
- The EHCI controller supports the HOSTPC register extension, and some
of the fields that the PHY needs to modify (PHCD and PTS) have moved
to the new HOSTPC register.
- Some of the UTMI PLL configuration registers have moved from the USB
register space to the Clock-And-Reset controller space. In Tegra30
the clock driver is responsible for configuring the UTMI PLL.
- The USBMODE register must be explicitly written to enter host mode.
- Certain PHY parameters need to be programmed for optimal signal
quality. Support for this will be added in the next patch.
The new tegra_phy_soc_config structure is added to describe the
differences between the SoCs.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The "nop" driver isn't a do-nothing-stub but supports a couple functions
like clock on/off or is able to use a voltage regulator. This patch
simply renames the driver to "generic" since it is easy possible to
extend it by a simple function istead of writing a complete driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Modified dwc3-omap to receive connect and disconnect notification using
extcon framework. Also did the necessary cleanups required after
adapting to extcon framework.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
commit 052a11d (usb: phy: make PHY driver selection
possible by controller drivers) changed the rules
on how drivers/usb/phy/of.c would be compiled and
failed to update include/linux/usb/of.h accordingly.
Because of that, we can fall into situations where
of_usb_get_phy_mode() is redefined. In order to fix
the error, we update the IS_ENABLED() check in
include/linux/usb/of.h to reflect the condition
where of.c is built.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new of_usb_get_dr_mode helper function for parsing dr_mode
from the device tree. Also replace the usage of the custom
tegra_usb_phy_mode enum with the standard enum.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Tegra EHCI driver is no longer using these custom functions, so they
can be removed.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB-related platform data is not used anymore in the Tegra USB drivers,
so remove all of it.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
struct usb_phy already has a field for the device pointer, so this
unnecessary field can be removed.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The tegra ehci driver has enabled USB vbus regulators directly using
GPIOs and the device tree attribute nvidia,vbus-gpio. This is ugly
and causes error messages on boot when both the regulator driver
and the ehci driver want access to the same GPIO.
After this patch, usb vbus regulators for tegra usb phy devices are specified
with the device tree attribute vbus-supply = <&x> where x is a regulator defined
in the device tree. The old nvidia,vbus-gpio property is no longer supported.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
usb_gadget_set_state() will call sysfs_notify()
which might sleep. Some users might want to call
usb_gadget_set_state() from the very IRQ handler
which actually changes the gadget state.
Instead of having every UDC driver add their own
workqueue for such a simple notification, we're
adding it generically to our struct usb_gadget,
so the details are hidden from all UDC drivers.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this helper will be used for controllers which
want to work at a lower speed even though they
support higher USB transfer rates.
One such case is Texas Instruments' AM437x
SoC where it uses a USB3 controller without
a USB3 PHY, rendering the controller USB2-only.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch centralizes computing of max rx/tx qlen, because:
- RX_QLEN()/TX_QLEN() is called in hot path
- computing depends on device's usb speed, now we have ls/fs, hs, ss,
so more checks need to be involved
- in fact, max rx/tx qlen should not only depend on device USB
speed, but also depend on ethernet link speed, so we need to
consider that in future.
- if SG support is done, max tx qlen may need change too
Generally, hard_mtu and rx_urb_size are changed in bind(), reset()
and link_reset() callback, and change mtu network operation, this
patches introduces the API of usbnet_update_max_qlen(), and calls
it in above path.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in
this branch, both containing almost no platform specific code at all,
since they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part of
the SoC specific code. With the changes done by Thomas Petazzoni, we can
now more easily have PCI host controller drivers as loadable modules and
keep them separate from the platform code in drivers/pci/host. This has
already led to the discovery that three platforms (exynos, spear and imx)
are actually using an identical PCIe host controller and will be able
to share a driver once support for spear and imx is added.
Conflicts:
* asm/glue-proc.h has one CPU type getting added that conflicts
with another addition in 3.10-rc7
* Simple context changes in arch/arm/Makefile and arch/arm/Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=0r9S
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and
EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
branch, both containing almost no platform specific code at all, since
they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part
of the SoC specific code. With the changes done by Thomas Petazzoni,
we can now more easily have PCI host controller drivers as loadable
modules and keep them separate from the platform code in
drivers/pci/host. This has already led to the discovery that three
platforms (exynos, spear and imx) are actually using an identical PCIe
host controller and will be able to share a driver once support for
spear and imx is added."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
ARM: integrator: let pciv3 use mem/premem from device tree
ARM: integrator: set local side PCI addresses right
ARM: dts: Add pcie controller node for exynos5440-ssdk5440
ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
ARM: EXYNOS: Enable PCIe support for Exynos5440
pci: Add PCIe driver for Samsung Exynos
ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
ARM: keystone: Move CPU bringup code to dedicated asm file
ARM: multiplatform: always pick one CPU type
ARM: imx: select syscon for IMX6SL
ARM: keystone: select ARM_ERRATA_798181 only for SMP
ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
ARM: OMAP2+: AM43x: resolve SMP related build error
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
...
"ci13xxx" is bad for at least the following reasons:
* people often mistype it
* it doesn't add any informational value to the names it's used in
* it needlessly attracts mail filters
This patch replaces it with "ci_hdrc", "ci_udc" or "ci_hw", depending
on the situation. Modules with ci13xxx prefix are also renamed accordingly
and aliases are added for compatibility. Otherwise, no functional changes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
on i386:
drivers/built-in.o: In function `ci_hdrc_probe':
core.c:(.text+0x20446b): undefined reference to `of_usb_get_phy_mode'
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra EHCI driver directly calls various functions in the Tegra USB
PHY driver. The reverse is also true; the PHY driver calls into the EHCI
driver. This is problematic when the two are built as modules.
The calls from the PHY to EHCI driver were originally added in commit
bbdabdb "usb: add APIs to access host registers from Tegra PHY", for the
following reasons:
1) The register being touched is an EHCI register, so logically only the
EHCI driver should touch it.
2) (1) implies that some locking may be needed to correctly implement the
r/m/w access to this shared register.
3) We were expecting to pass only the PHY register space to the Tegra PHY
driver, and hence it would not have access to touch the shared
registers.
To solve this, that commit added functions in the EHCI driver to touch the
shared register on behalf of the PHY driver.
In practice, we ended up not having any locking in the implementaiton of
those functions, and I've been led to believe this is safe. Equally, (3)
did not happen either. Hence, it is possible for the PHY driver to touch
the shared register directly.
Given that, this patch moves the code to touch the shared register back
into the PHY driver, to eliminate the module problems. If we actually
need locking or co-ordination in the future, I propose we put the lock
support into some pre-existing core module, or into a third separate
module, in order to avoid the circular dependencies.
I apologize for my contribution to code churn here.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if a chipidea core is otg capable the board may not be. This allows
to explicitly set the core to host/peripheral mode. Without these flags
the driver falls back to the old behaviour.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes it possible to configure the PTW, PTS and STS bits
inside the portsc register for host and device mode before the driver
starts and the phy can be addressed as hardware implementation is
designed.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds two little devicetree helper functions for determining the
dr_mode (host, peripheral, otg) and phy_type (utmi, ulpi,...) from
the devicetree.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We had the limit of 255 USB to serial devices on one system for almost
15 years, with no complaints. But now it's time to move on from these
tiny "baby" systems, and bump the number up to 512, which should last
us a few more years:
"512 is a nice number" -- Tobias Winter
Note, this is still a static value, and uses up tty core memory with
this many tty devices allocated. Converting the driver to use
TTY_DRIVER_DYNAMIC_DEV is the next thing to do in order to remove this
limitation.
Reported-by: Tobias Winter <tobias@linuxdingsda.de>
Tested-by: Tobias Winter <tobias@linuxdingsda.de>
Reviewed-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the allocation of minor device numbers from a static array to
be dynamic, using the idr interface. This means that you could
potentially get "gaps" in a minor number range for a single USB serial
device with multiple ports, but all should still work properly.
We remove the 'minor' field from the usb_serial structure, as it no
longer makes any sense for it (use the field in the usb_serial_port
structure if you really want to know this number), and take the fact
that we were overloading a number in this field to determine if we had
initialized the minor numbers or not, and just use a flag variable
instead.
Note, we still have the limitation of 255 USB to serial devices in the
system, as that is all we are registering with the TTY layer at this
point in time.
Tested-by: Tobias Winter <tobias@linuxdingsda.de>
Reviewed-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These updates are by Sergei Shtylyov to clean-up USB support
present for R8A7779/Marzen and then extend USB support coverage to
R8A7778/BOCK-W.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=5+Te
-----END PGP SIGNATURE-----
Merge tag 'renesas-phy-rcar-usb-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Renesas USB updates for v3.11
These updates are by Sergei Shtylyov to clean-up USB support
present for R8A7779/Marzen and then extend USB support coverage to
R8A7778/BOCK-W.
* tag 'renesas-phy-rcar-usb-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: BOCK-W: add USB support
ARM: shmobile: r8a7778: add USB support
phy-rcar-usb: add R8A7778 support
phy-rcar-usb: handle platform data
ARM: shmobile: Marzen: pass platform data to USB PHY device
phy-rcar-usb: add platform data
phy-rcar-usb: correct base address
ARM: shmobile: r8a7779: remove USB PHY 2nd memory resource
phy-rcar-usb: remove EHCI internal buffer setup
ARM: shmobile: r8a7779: setup EHCI internal buffer
ehci-platform: add pre_setup() method to platform data
ARM: shmobile: Marzen: move USB EHCI, OHCI, and PHY devices to R8A7779 code
Conflicts:
arch/arm/mach-shmobile/board-marzen.c
arch/arm/mach-shmobile/setup-r8a7778.c
Signed-off-by: Olof Johansson <olof@lixom.net>
All function drivers are now converted to our new configfs-based
binding. Eventually this will help us getting rid of in-kernel
gadget drivers and only keep function drivers in the kernel.
MUSB was taught that it needs to be built for host-only and
device-only modes too. We had this support long ago but it
involved a ridiculous amount of ifdefs. Now we have a much
cleaner approach.
Samsung Exynos4 platform now implements HSIC support.
We're introducing support for AB8540 and AB9540 PHYs.
MUSB module reinsertion now works as expected, before we were
getting -EBUSY being returned by the resource checks done on
driver core.
DWC3 now has minimum support for TI's AM437x series of SoCs.
OMAP5 USB3 PHY learned one extra DPLL configuration values because
that PHY is reused in TI's DRA7xx devices.
We're introducing support for Faraday fotg210 UDCs.
Last, but not least, the usual set of non-critical fixes and cleanups
ranging from usage of platform_{get,set}_drvdata to lock improvements.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=O9AH
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.11 merge window
All function drivers are now converted to our new configfs-based
binding. Eventually this will help us getting rid of in-kernel
gadget drivers and only keep function drivers in the kernel.
MUSB was taught that it needs to be built for host-only and
device-only modes too. We had this support long ago but it
involved a ridiculous amount of ifdefs. Now we have a much
cleaner approach.
Samsung Exynos4 platform now implements HSIC support.
We're introducing support for AB8540 and AB9540 PHYs.
MUSB module reinsertion now works as expected, before we were
getting -EBUSY being returned by the resource checks done on
driver core.
DWC3 now has minimum support for TI's AM437x series of SoCs.
OMAP5 USB3 PHY learned one extra DPLL configuration values because
that PHY is reused in TI's DRA7xx devices.
We're introducing support for Faraday fotg210 UDCs.
Last, but not least, the usual set of non-critical fixes and cleanups
ranging from usage of platform_{get,set}_drvdata to lock improvements.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Sometimes there is a need to initialize some non-standard registers mapped to
the EHCI region before accessing the standard EHCI registers. Add pre_setup()
method with 'struct usb_hcd *' parameter to be called just before ehci_setup()
to the 'ehci-platform' driver's platform data for this purpose...
While at it, add the missing incomplete declaration of 'struct platform_device'
to <linux/usb/ehci_pdriver.h>...
The patch has been tested on the Marzen and BOCK-W boards.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The usb_serial_port structure had the number field, which was the minor
number for the port, which almost no one really cared about. They
really wanted the number of the port within the device, which you had to
subtract from the minor of the parent usb_serial_device structure. To
clean this up, provide the real minor number of the port, and the number
of the port within the serial device separately, as these numbers might
not be related in the future.
Bonus is that this cleans up a lot of logic in the drivers, and saves
lines overall.
Tested-by: Tobias Winter <tobias@linuxdingsda.de>
Reviewed-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
--
drivers/staging/serqt_usb2/serqt_usb2.c | 21 +++--------
drivers/usb/serial/ark3116.c | 2 -
drivers/usb/serial/bus.c | 6 +--
drivers/usb/serial/console.c | 2 -
drivers/usb/serial/cp210x.c | 2 -
drivers/usb/serial/cypress_m8.c | 4 +-
drivers/usb/serial/digi_acceleport.c | 6 ---
drivers/usb/serial/f81232.c | 5 +-
drivers/usb/serial/garmin_gps.c | 6 +--
drivers/usb/serial/io_edgeport.c | 58 ++++++++++++--------------------
drivers/usb/serial/io_ti.c | 21 ++++-------
drivers/usb/serial/keyspan.c | 29 +++++++---------
drivers/usb/serial/metro-usb.c | 4 +-
drivers/usb/serial/mos7720.c | 37 +++++++++-----------
drivers/usb/serial/mos7840.c | 52 +++++++++-------------------
drivers/usb/serial/opticon.c | 2 -
drivers/usb/serial/pl2303.c | 2 -
drivers/usb/serial/quatech2.c | 7 +--
drivers/usb/serial/sierra.c | 2 -
drivers/usb/serial/ti_usb_3410_5052.c | 10 ++---
drivers/usb/serial/usb-serial.c | 7 ++-
drivers/usb/serial/usb_wwan.c | 2 -
drivers/usb/serial/whiteheat.c | 20 +++++------
include/linux/usb/serial.h | 6 ++-
24 files changed, 133 insertions(+), 180 deletions(-)
This patch adds the HWA specific members to struct usb_rpipe_descriptor
and sets them correctly based on the wireless endpoint compananion
descriptor.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds Wireless USB root hub support to the USB HCD. It allows
the HWA to create its root hub which previously failed because the HCD
treated wireless root hubs the same as USB2 high speed hubs. The creation
of the root hub would fail in that case due to lack of TTs which wireless
root hubs do not support.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Registered Tegra USB PHY as a separate platform driver.
To synchronize host controller and PHY initialization, used deferred
probe mechanism. As PHY should be initialized before EHCI starts running,
deferred probe of Tegra EHCI driver till PHY probe gets completed.
Got rid of instance number based handling in host driver.
Made use of DT params to get the PHY Pad registers.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As GPIO information is avail through DT, used it to get Tegra ULPI
reset GPIO number. Added a new member to tegra_usb_phy structure to
store this number.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added a new PHY mode to support OTG.
Obtained Tegra USB PHY mode using DT property.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add generic wait_until_sent implementation which polls for empty
hardware buffers using the new port-operation tx_empty.
The generic implementation will be used for all sub-drivers that
implement tx_empty but does not define wait_until_sent.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add wait_until_sent operation which can be used to wait for hardware
buffers to drain.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tidy up kernel-doc content for USB GADGET. No functional change.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some drivers (sierra_net) need the status interrupt URB
active even when the device is closed, because they receive
custom indications from firmware. Add functions to refcount
the status interrupt URB submit/kill operation so that
sub-drivers and the generic driver don't fight over whether
the status interrupt URB is active or not.
A sub-driver can call usbnet_status_start() at any time, but
the URB is only submitted the first time the function is
called. Likewise, when the sub-driver is done with the URB,
it calls usbnet_status_stop() but the URB is only killed when
all users have stopped it. The URB is still killed and
re-submitted for suspend/resume, as before, with the same
refcount it had at suspend.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly many small changes spread as seen in diffstat in sound/*
directory by this update. A significant change in the subsystem level
is the introduction of snd_soc_component, which will help more generic
handling of SoC and off-SoC components.
Also, snd_BUG_ON() macro is enabled unconditionally now due to its
misuses, so people might hit kernel warnings (it's a good thing for
us).
- compress-offload: support for capture by Charles Keepax
- HD-audio: codec delay support by Dylan Reid
- HD-audio: improvements/fixes in generic parser: better headphone mic
and headset mic support, jack_modes hint consolidation, proper beep
attach/detachment, generalized power filter controls by David
Henningsson, et al
- HD-audio: Improved management of HDMI codec pins/converters
- HD-audio: Better pin/DAC assignment for VIA codecs
- HD-audio: Haswell HDMI workarounds
- HD-audio: ALC268 codec support, a few new quirks for Chromebooks
- USB: regression fixes: USB-MIDI autopm fix, the recent ISO latency
fix by Clemens Ladisch
- USB: support for DSD formats by Daniel Mack
- USB: A few UAC2 device endian/cock fixes by Eldad Zack
- USB: quirks for Emu 192kHz support, Novation Twitch DJ controller,
Yamaha THRxx devices
- HDSPM: updates for TCO controls by Adrian Knoth
- ASoC: Add a snd_soc_component object type for generic handling of
SoC and off-SoC components by Kuninori Morimoto,
- dmaengine: a large set of cleanups and conversions by Lars-Peter
Clausen
- ASoC DAPM: performance optimizations from Ryo Tsutsui
- ASoC DAPM: support for mixer control sharing by Stephen Warren
- ASoC: multiplatform ARM cleanups from Arnd Bergmann
- ASoC: new codec drivers for AK5385 and TAS5086 from Daniel Mack
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=sYiI
-----END PGP SIGNATURE-----
Merge tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Mostly many small changes spread as seen in diffstat in sound/*
directory by this update. A significant change in the subsystem level
is the introduction of snd_soc_component, which will help more generic
handling of SoC and off-SoC components.
Also, snd_BUG_ON() macro is enabled unconditionally now due to its
misuses, so people might hit kernel warnings (it's a good thing for
us).
- compress-offload: support for capture by Charles Keepax
- HD-audio: codec delay support by Dylan Reid
- HD-audio: improvements/fixes in generic parser: better headphone
mic and headset mic support, jack_modes hint consolidation, proper
beep attach/detachment, generalized power filter controls by David
Henningsson, et al
- HD-audio: Improved management of HDMI codec pins/converters
- HD-audio: Better pin/DAC assignment for VIA codecs
- HD-audio: Haswell HDMI workarounds
- HD-audio: ALC268 codec support, a few new quirks for Chromebooks
- USB: regression fixes: USB-MIDI autopm fix, the recent ISO latency
fix by Clemens Ladisch
- USB: support for DSD formats by Daniel Mack
- USB: A few UAC2 device endian/cock fixes by Eldad Zack
- USB: quirks for Emu 192kHz support, Novation Twitch DJ controller,
Yamaha THRxx devices
- HDSPM: updates for TCO controls by Adrian Knoth
- ASoC: Add a snd_soc_component object type for generic handling of
SoC and off-SoC components by Kuninori Morimoto,
- dmaengine: a large set of cleanups and conversions by Lars-Peter
Clausen
- ASoC DAPM: performance optimizations from Ryo Tsutsui
- ASoC DAPM: support for mixer control sharing by Stephen Warren
- ASoC: multiplatform ARM cleanups from Arnd Bergmann
- ASoC: new codec drivers for AK5385 and TAS5086 from Daniel Mack"
* tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (315 commits)
ALSA: usb-audio: caiaq: fix endianness bug in snd_usb_caiaq_maschine_dispatch
ALSA: asihpi: add format support check in snd_card_asihpi_capture_formats
ALSA: pcm_format_to_bits strong-typed conversion
ALSA: compress: fix the states to check for allowing read
ALSA: hda - Move Thinkpad X220 to use auto parser
ALSA: USB: adjust for changed 3.8 USB API
ALSA: usb - Avoid unnecessary sample rate changes on USB 2.0 clock sources
sound: oss/dmabuf: use dma_map_single
ALSA: ali5451: use mdelay instead of large udelay constants
ALSA: hda - Add the support for ALC286 codec
ALSA: usb-audio: USB quirk for Yamaha THR10C
ALSA: usb-audio: USB quirk for Yamaha THR5A
ALSA: usb-audio: USB quirk for Yamaha THR10
ALSA: usb-audio: Fix autopm error during probing
ALSA: snd-usb: try harder to find USB_DT_CS_ENDPOINT
ALSA: sound kconfig typo
ALSA: emu10k1: Fix dock firmware loading
ASoC: ux500: forward declare msp_i2s_platform_data
ASoC: davinci-mcasp: Add Support BCLK-to-LRCLK ratio for TDM modes
ASoC: davinci-pcm, davinci-mcasp: Clean up active_serializers
...
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
Both phy-tegra-usb.c and ehci-tegra.c export symbols used by the other one,
which does not work if one of them or both are loadable modules, resulting
in an error like:
drivers/built-in.o: In function `utmi_phy_clk_disable':
drivers/usb/phy/phy-tegra-usb.c:302: undefined reference to `tegra_ehci_set_phcd'
drivers/built-in.o: In function `utmi_phy_clk_enable':
drivers/usb/phy/phy-tegra-usb.c:324: undefined reference to `tegra_ehci_set_phcd'
drivers/built-in.o: In function `utmi_phy_power_on':
drivers/usb/phy/phy-tegra-usb.c:447: undefined reference to `tegra_ehci_set_pts'
This turns the interface into a one-way dependency by letting the tegra ehci
driver pass two function pointers for callbacks that need to be called by
the phy driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bunch of changes here, the most interesting one subsystem wise being
Morimoto-san's work to create snd_soc_component which doesn't do much
for now but will be pretty important going forwards:
- Add a new component object type which will form the basis of moving
to a more generic handling of SoC and off-SoC components, contributed
by Kuninori Morimoto.
- A fairly large set of cleanups for the dmaengine integration from
Lars-Peter Clausen, starting to move towards being able to have a
generic driver based on the library.
- Performance optimisations to DAPM from Ryo Tsutsui.
- Support for mixer control sharing in DAPM from Stephen Warren.
- Multiplatform ARM cleanups from Arnd Bergmann.
- New CODEC drivers for AK5385 and TAS5086 from Daniel Mack.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lx37
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.10
A bunch of changes here, the most interesting one subsystem wise being
Morimoto-san's work to create snd_soc_component which doesn't do much
for now but will be pretty important going forwards:
- Add a new component object type which will form the basis of moving
to a more generic handling of SoC and off-SoC components, contributed
by Kuninori Morimoto.
- A fairly large set of cleanups for the dmaengine integration from
Lars-Peter Clausen, starting to move towards being able to have a
generic driver based on the library.
- Performance optimisations to DAPM from Ryo Tsutsui.
- Support for mixer control sharing in DAPM from Stephen Warren.
- Multiplatform ARM cleanups from Arnd Bergmann.
- New CODEC drivers for AK5385 and TAS5086 from Daniel Mack.
The link change is detected via the interrupt pipe, and bulk
pipes are responsible for transfering packets, so it is reasonable
to stop bulk transfer after link is reported as off.
Two adavantages may be obtained with stopping bulk transfer
after link becomes off:
- USB bus bandwidth is saved(USB bus is shared bus except for
USB3.0), for example, lots of 'IN' token packets and 'NYET'
handshake packets is transfered on 2.0 bus.
- probabaly power might be saved for usb host controller since
cancelling bulk transfer may disable the asynchronous schedule of
host controller.
With this patch, when link becomes off, about ~10% performance
boost can be found on bulk transfer of anther usb device which
is attached to same bus with the usbnet device, see below
test on next-20130410:
- read from usb mass storage(Sandisk Extreme USB 3.0) on pandaboard
with below command after unplugging ethernet cable:
dd if=/dev/sda iflag=direct of=/dev/null bs=1M count=800
- without the patch
1, 838860800 bytes (839 MB) copied, 36.2216 s, 23.2 MB/s
2, 838860800 bytes (839 MB) copied, 35.8368 s, 23.4 MB/s
3, 838860800 bytes (839 MB) copied, 35.823 s, 23.4 MB/s
4, 838860800 bytes (839 MB) copied, 35.937 s, 23.3 MB/s
5, 838860800 bytes (839 MB) copied, 35.7365 s, 23.5 MB/s
average: 23.6MB/s
- with the patch
1, 838860800 bytes (839 MB) copied, 32.3817 s, 25.9 MB/s
2, 838860800 bytes (839 MB) copied, 31.7389 s, 26.4 MB/s
3, 838860800 bytes (839 MB) copied, 32.438 s, 25.9 MB/s
4, 838860800 bytes (839 MB) copied, 32.5492 s, 25.8 MB/s
5, 838860800 bytes (839 MB) copied, 31.6178 s, 26.5 MB/s
average: 26.1MB/s
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the API of usbnet_link_change, so that
usbnet can handle link change centrally, which may help to
implement killing traffic URBs for saving USB bus bandwidth
and host controller power.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the big Gadget & PHY pull request. Many of us have
been really busy lately getting multiple drivers to a better
position.
Since this pull request is so large, I will divide it in sections
so it's easier to grasp what's included.
- cleanups:
. UDC drivers no longer touch gadget->dev, that's now udc-core
responsibility
. Many more UDC drivers converted to usb_gadget_map/unmap_request()
. UDC drivers no longer initialize DMA-related fields from gadget's
device structure
. UDC drivers don't touch gadget.dev.driver directly
. UDC drivers don't assign gadget.dev.release directly
. Removal of some unused DMA_ADDR_INVALID
. Introduction of CONFIG_USB_PHY
. All phy drivers have been moved to drivers/usb/phy and renamed to
a common naming scheme
. Fix PHY layer so it never returns a NULL pointer, also fix all
callers to avoid using IS_ERR_OR_NULL()
. Sparse fixes all over the place
. drivers/usb/otg/ has been deleted
. Marvel drivers (mv_udc, ehci-mv, mv_otg and mv_u3d) improved clock
usage
- new features:
. UDC core now provides a generic way for tracking and reporting
UDC's state (not attached, resuming, suspended, addressed,
default, etc)
. twl4030-usb learned that it shouldn't be enabled during init
. Full DT support for DWC3 has been implemented
. ab8500-usb learned about pinctrl framework
. nop PHY learned about DeviceTree and regulators
. DWC3 learned about suspend/resume
. DWC3 can now be compiled in host-only and gadget-only (as well as
DRD) configurations
. UVC now enables streaming endpoint based on negotiated speed
. isp1301 now implements the PHY API properly
. configfs-based interface for gadget drivers which will lead to
the removal of all code which just combines functions together
to build functional gadget drivers.
. f_serial and f_obex were converted to new configfs interface while
maintaining old interface around.
- non-critical fixes:
. UVC gadget driver got fixes for Endpoint usage and stream calculation
. ab8500-usb fixed unbalanced clock and regulator API usage
. twl4030-usb got a fix for when OMAP3 is booted with cable connected
. fusb300_udc got a fix for DMA usage
. UVC got fixes for two assertions of the USB Video Class Compliance
specification revision 1.1
. build warning issues caused by recent addition of __must_check to
regulator API
These are all changes which deserve a mention, all other changes are related
to these one or minor spelling fixes and other similar tasks.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=aF4r
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.10 merge window
Here is the big Gadget & PHY pull request. Many of us have
been really busy lately getting multiple drivers to a better
position.
Since this pull request is so large, I will divide it in sections
so it's easier to grasp what's included.
- cleanups:
. UDC drivers no longer touch gadget->dev, that's now udc-core
responsibility
. Many more UDC drivers converted to usb_gadget_map/unmap_request()
. UDC drivers no longer initialize DMA-related fields from gadget's
device structure
. UDC drivers don't touch gadget.dev.driver directly
. UDC drivers don't assign gadget.dev.release directly
. Removal of some unused DMA_ADDR_INVALID
. Introduction of CONFIG_USB_PHY
. All phy drivers have been moved to drivers/usb/phy and renamed to
a common naming scheme
. Fix PHY layer so it never returns a NULL pointer, also fix all
callers to avoid using IS_ERR_OR_NULL()
. Sparse fixes all over the place
. drivers/usb/otg/ has been deleted
. Marvel drivers (mv_udc, ehci-mv, mv_otg and mv_u3d) improved clock
usage
- new features:
. UDC core now provides a generic way for tracking and reporting
UDC's state (not attached, resuming, suspended, addressed,
default, etc)
. twl4030-usb learned that it shouldn't be enabled during init
. Full DT support for DWC3 has been implemented
. ab8500-usb learned about pinctrl framework
. nop PHY learned about DeviceTree and regulators
. DWC3 learned about suspend/resume
. DWC3 can now be compiled in host-only and gadget-only (as well as
DRD) configurations
. UVC now enables streaming endpoint based on negotiated speed
. isp1301 now implements the PHY API properly
. configfs-based interface for gadget drivers which will lead to
the removal of all code which just combines functions together
to build functional gadget drivers.
. f_serial and f_obex were converted to new configfs interface while
maintaining old interface around.
- non-critical fixes:
. UVC gadget driver got fixes for Endpoint usage and stream calculation
. ab8500-usb fixed unbalanced clock and regulator API usage
. twl4030-usb got a fix for when OMAP3 is booted with cable connected
. fusb300_udc got a fix for DMA usage
. UVC got fixes for two assertions of the USB Video Class Compliance
specification revision 1.1
. build warning issues caused by recent addition of __must_check to
regulator API
These are all changes which deserve a mention, all other changes are related
to these one or minor spelling fixes and other similar tasks.
Signed-of-by: Felipe Balbi <balbi@ti.com>
|# modprobe dummy_hcd num=2
|# modprobe libcomposite
|# lsmod
|Module Size Used by
|libcomposite 31648 0
|dummy_hcd 19871 0
|# mkdir /sys/kernel/config/usb_gadget/oha
|# cd /sys/kernel/config/usb_gadget/oha
|# mkdir configs/def.1
|# mkdir configs/def.2
|# mkdir functions/acm.ttyS1
|# mkdir strings/0x1
|mkdir: cannot create directory `strings/0x1': Invalid argument
|# mkdir strings/0x409
|# mkdir strings/1033
|mkdir: cannot create directory `strings/1033': File exists
|# mkdir strings/1032
|# mkdir configs/def.1/strings/0x409
|# mkdir configs/def.2/strings/0x409
|#find . -ls
| 975 0 drwxr-xr-x 5 root root 0 Dec 23 17:40 .
| 978 0 drwxr-xr-x 4 root root 0 Dec 23 17:43 ./strings
| 4100 0 drwxr-xr-x 2 root root 0 Dec 23 17:43 ./strings/1032
| 995 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./strings/1032/serialnumber
| 996 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./strings/1032/product
| 997 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./strings/1032/manufacturer
| 2002 0 drwxr-xr-x 2 root root 0 Dec 23 17:41 ./strings/0x409
| 998 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./strings/0x409/serialnumber
| 999 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./strings/0x409/product
| 1000 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./strings/0x409/manufacturer
| 977 0 drwxr-xr-x 4 root root 0 Dec 23 17:41 ./configs
| 4081 0 drwxr-xr-x 3 root root 0 Dec 23 17:41 ./configs/def.2
| 4082 0 drwxr-xr-x 3 root root 0 Dec 23 17:42 ./configs/def.2/strings
| 2016 0 drwxr-xr-x 2 root root 0 Dec 23 17:42 ./configs/def.2/strings/0x409
| 1001 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./configs/def.2/strings/0x409/configuration
| 1002 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./configs/def.2/bmAttributes
| 1003 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./configs/def.2/MaxPower
| 979 0 drwxr-xr-x 3 root root 0 Dec 23 17:42 ./configs/def.1
| 980 0 drwxr-xr-x 3 root root 0 Dec 23 17:42 ./configs/def.1/strings
| 5122 0 drwxr-xr-x 2 root root 0 Dec 23 17:42 ./configs/def.1/strings/0x409
| 1004 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./configs/def.1/strings/0x409/configuration
| 1005 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./configs/def.1/bmAttributes
| 1006 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./configs/def.1/MaxPower
| 976 0 drwxr-xr-x 3 root root 0 Dec 23 17:41 ./functions
| 981 0 drwxr-xr-x 2 root root 0 Dec 23 17:41 ./functions/acm.ttyS1
| 1007 0 -r--r--r-- 1 root root 4096 Dec 23 17:43 ./functions/acm.ttyS1/port_num
| 1008 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./UDC
| 1009 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./bcdUSB
| 1010 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./bcdDevice
| 1011 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./idProduct
| 1012 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./idVendor
| 1013 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./bMaxPacketSize0
| 1014 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./bDeviceProtocol
| 1015 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./bDeviceSubClass
| 1016 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./bDeviceClass
|# cat functions/acm.ttyS1/port_num
|0
|# ls -lah /dev/ttyGS*
|crw-rw---T 1 root dialout 252, 0 Dec 23 17:41 /dev/ttyGS0
|
|# echo 0x1234 > idProduct
|# echo 0xabcd > idVendor
|# echo 1122 > strings/0x409/serialnumber
|# echo "The manufacturer" > strings/0x409/manufacturer
|# echo 1 > strings/1032/manufacturer
|# echo 1sa > strings/1032/product
|# echo tada > strings/1032/serialnumber
|echo "Primary configuration" > configs/def.1/strings/0x409/configuration
|# echo "Secondary configuration" > configs/def.2/strings/0x409/configuration
|# ln -s functions/acm.ttyS1 configs/def.1/
|# ln -s functions/acm.ttyS1 configs/def.2/
|find configs/def.1/ -ls
| 979 0 drwxr-xr-x 3 root root 0 Dec 23 17:49 configs/def.1/
| 6264 0 lrwxrwxrwx 1 root root 0 Dec 23 17:48 configs/def.1/acm.ttyS1 -> ../../../../usb_gadget/oha/functions/acm.ttyS1
| 980 0 drwxr-xr-x 3 root root 0 Dec 23 17:42 configs/def.1/strings
| 5122 0 drwxr-xr-x 2 root root 0 Dec 23 17:49 configs/def.1/strings/0x409
| 6284 0 -rw-r--r-- 1 root root 4096 Dec 23 17:47 configs/def.1/strings/0x409/configuration
| 6285 0 -rw-r--r-- 1 root root 4096 Dec 23 17:49 configs/def.1/bmAttributes
| 6286 0 -rw-r--r-- 1 root root 4096 Dec 23 17:49 configs/def.1/MaxPower
|
|echo 120 > configs/def.1/MaxPower
|
|# ls -lh /sys/class/udc/
|total 0
|lrwxrwxrwx 1 root root 0 Dec 23 17:50 dummy_udc.0 -> ../../devices/platform/dummy_udc.0/udc/dummy_udc.0
|lrwxrwxrwx 1 root root 0 Dec 23 17:50 dummy_udc.1 -> ../../devices/platform/dummy_udc.1/udc/dummy_udc.1
|# echo dummy_udc.0 > UDC
|# lsusb
|Bus 001 Device 002: ID abcd:1234 Unknown
|
|lsusb -d abcd:1234 -v
|Device Descriptor:
…
| idVendor 0xabcd Unknown
| idProduct 0x1234
| bcdDevice 3.06
| iManufacturer 1 The manufacturer
| iProduct 2
| iSerial 3 1122
| bNumConfigurations 2
…
|echo "" > UDC
v5…v6
- wired up strings with usb_gstrings_attach()
- add UDC attribe. Write "udc-name" will bind the gadget. Write an empty
string (it should contain \n since 0 bytes write get optimzed away)
will unbind the UDC from the gadget. The name of available UDCs can be
obtained from /sys/class/udc/
v4…v5
- string rework. This will add a strings folder incl. language code like
strings/409/manufacturer
as suggested by Alan.
- rebased ontop reworked functions.c which has usb_function_instance
which is used prior after "mkdir acm.instance" and can be directly
used for configuration via configfs.
v3…v4
- moved functions from the root folde down to the gadget as suggested
by Michał
- configs have now their own configs folder as suggested by Michał.
The folder is still name.bConfigurationValue where name becomes the
sConfiguration. Is this usefull should we just stilc
configs/bConfigurationValue/ ?
- added configfs support to the ACM function. The port_num attribute is
exported by f_acm. An argument has been added to the USB alloc
function to distinguish between "old" (use facm_configure() to
configure and configfs interface (expose a config_node).
The port_num is currently a dumb counter. It will
require some function re-work to make it work.
scheduled for v5:
- sym linking function into config.
v2…v3
- replaced one ifndef by ifdef as suggested by Micahał
- strstr()/strchr() function_make as suggested by Micahł
- replace [iSerialNumber|iProduct|iManufacturer] with
[sSerialNumber|sProduct|sManufacturer] as suggested by Alan
- added creation of config descriptors
v1…v2
- moved gadgets from configfs' root directory into /udcs/ within our
"usb_gadget" folder. Requested by Andrzej & Michał
- use a dot as a delimiter between function's name and its instance's name
as suggested by Michał
- renamed all config_item_type, configfs_group_operations, make_group,
drop_item as suggested by suggested by Andrzej to remain consisten
within this file and within other configfs users
- Since configfs.c and functions.c are now part of the udc-core module,
the module itself is now called udc. Also added a tiny ifdef around
init code becuase udc-core is subsys init and this is too early for
configfs in the built-in case. In the module case, we can only have
one init function.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixup below sparse errors
CHECK ${RENESAS_USB}/common.c
${RENESAS_USB}/common.c:313:17: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:322:17: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:384:17: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:524:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:545:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:574:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:606:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/mod_gadget.c:233:28: warning: symbol 'req_clear_feature' was not declared. Should it be static?
${RENESAS_USB}/mod_gadget.c:274:28: warning: symbol 'req_set_feature' was not declared. Should it be static?
${RENESAS_USB}/mod_gadget.c:375:28: warning: symbol 'req_get_status' was not declared. Should it be static?
[ balbi@ti.com : added three sparse fixes to mod_gadget.c ]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch (as1675) removes the CONFIG_USB_SUSPEND option, essentially
replacing it everywhere with CONFIG_PM_RUNTIME (except for one place
in hub.c, where it is replaced with CONFIG_PM because the code needs
to be used in both runtime and system PM). The net result is code
shrinkage and simplification.
There's very little point in keeping CONFIG_USB_SUSPEND because almost
everybody enables it. The few that don't will find that the usbcore
module has gotten somewhat bigger and they will have to take active
measures if they want to prevent hubs from being runtime suspended.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the port MSR-wait queue now that all drivers have been migrated
to the tty-port queue.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add generic get_icount implementation that subdrivers relying on the
port interrupt counters can use.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add generic TIOCMIWAIT implementation which correctly handles hangup,
USB-device disconnect, does not rely on the deprecated sleep_on
functions and hence does not suffer from the races currently affecting
several usb-serial drivers.
This makes it much easier to add TIOCMIWAIT support to subdrivers as the
tricky details related to hangup and disconnect (e.g. atomicity, that
the private port data may have been freed when woken up, and waking up
processes at disconnect) have been handled once and for all.
To add support to a subdriver, simply set the tiocmiwait-port-operation
field, update the port icount fields and wake up any process sleeping on
the tty-port modem-status-change wait queue on changes.
Note that the tty-port initialised flag can be used to detect
disconnected as the port will be hung up as part of disconnect (and
cannot be reactivated due to the disconnected flag). However, as the
tty-port implementation currently wakes up processes before calling port
shutdown, the tty-hupping flag must also be checked to detect hangup for
now.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove empty generic release implementation and make the release
callback non-mandatory (like attach, probe and disconnect).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the now empty generic disconnect callback and make the disconnect
callback non-mandatory.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userspace applications need to know the maximum supported message
size.
The cdc-wdm driver translates between a character device stream
and a message based protocol. Each message is transported as a
usb control message with no further encapsulation or syncronization.
Each read or write on the character device should translate to
exactly one usb control message to ensure that message boundaries
are kept intact. That means that the userspace application must
know the maximum message size supported by the device and driver,
making this size a vital part of the cdc-wdm character device API.
CDC WDM and CDC MBIM functions export the maximum supported
message size through CDC functional descriptors. The cdc-wdm and
cdc_mbim drivers will parse these descriptors and use the value
chosen by the device. The only current way for a userspace
application to retrive the value is by duplicating the descriptor
parsing. This is an unnecessary complex task, and application
writers are likely to postpone it, using a fixed value and adding
a "todo" item.
QMI functions have no way to tell the host what message size they
support. The qmi_wwan driver use a fixed value based on protocol
recommendations and observed device behaviour. Userspace
applications must know and hard code the same value. This scheme
will break if we ever encounter a QMI device needing a device
specific message size quirk. We are currently unable to support
such a device because using a non default size would break the
implicit userspace API.
The message size is currently a hidden attribute of the cdc-wdm
userspace API. Retrieving it is unnecessarily complex, increasing
the possibility of drivers and applications using different limits.
The resulting errors are hard to debug, and can only be replicated
on identical hardware.
Exporting the maximum message size from the driver simplifies the
task for the userspace application, and creates a unified
information source independent of device and function class. It also
serves to document that the message size is part of the cdc-wdm
userspace API.
This proposed API extension has been presented for the authors of
userspace applications and libraries using the current API: libmbim,
libqmi, uqmi, oFono and ModemManager. The replies were:
Aleksander Morgado:
"We do really need max message size for MBIM; and as you say, it may be
good to have the max message size info also for QMI, so the new ioctl
seems a good addition. So +1 from my side, for what it's worth."
Dan Williams:
"Yeah, +1 here. I'd prefer the sysfs file, but the fact that that
doesn't work for fd passing pretty much kills it."
No negative replies are so far received.
Cc: Aleksander Morgado <aleksander@lanedo.com>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver divides the root hub into two logical hubs which work
respectively for usb 2.0 and usb 3.0 devices. They are independent
devices in the usb core. But in the ACPI table, it's one device node
and all usb2.0 and usb3.0 ports are under it. Binding usb port with
its acpi node needs the raw port number which is reflected in the xhci
extended capabilities table. This patch is to add find_raw_port_number
callback to struct hc_driver(), fill it with xhci_find_raw_port_number()
which will return raw port number and add a wrap usb_hcd_find_raw_port_number().
Otherwise, refactor xhci_find_real_port_number(). Using
xhci_find_raw_port_number() to get real index in the HW port status
registers instead of scanning through the xHCI roothub port array.
This can help to speed up.
All addresses in xhci->usb2_ports and xhci->usb3_ports array are
kown good ports and don't include following bad ports in the extended
capabilities talbe.
(1) root port that doesn't have an entry
(2) root port with unknown speed
(3) root port that is listed twice and with different speeds.
So xhci_find_raw_port_number() will only return port num of good ones
and never touch bad ports above.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Here are a number of USB fixes that resolve issues that have been reported
against 3.9-rc3.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlFMnR0ACgkQMUfUDdst+yliJwCeNOJ0bz7Crzs3NepnRWHaHJ0Z
OmQAnRvQMX1OpqDCsjnc7RW2gL/2TDNd
=05gg
-----END PGP SIGNATURE-----
Merge tag 'usb-3.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a number of USB fixes that resolve issues that have been
reported against 3.9-rc3."
* tag 'usb-3.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (37 commits)
USB: ti_usb_3410_5052: fix use-after-free in TIOCMIWAIT
USB: ssu100: fix use-after-free in TIOCMIWAIT
USB: spcp8x5: fix use-after-free in TIOCMIWAIT
USB: quatech2: fix use-after-free in TIOCMIWAIT
USB: pl2303: fix use-after-free in TIOCMIWAIT
USB: oti6858: fix use-after-free in TIOCMIWAIT
USB: mos7840: fix use-after-free in TIOCMIWAIT
USB: mos7840: fix broken TIOCMIWAIT
USB: mct_u232: fix use-after-free in TIOCMIWAIT
USB: io_ti: fix use-after-free in TIOCMIWAIT
USB: io_edgeport: fix use-after-free in TIOCMIWAIT
USB: ftdi_sio: fix use-after-free in TIOCMIWAIT
USB: f81232: fix use-after-free in TIOCMIWAIT
USB: cypress_m8: fix use-after-free in TIOCMIWAIT
USB: ch341: fix use-after-free in TIOCMIWAIT
USB: ark3116: fix use-after-free in TIOCMIWAIT
USB: serial: add modem-status-change wait queue
USB: serial: fix interface refcounting
USB: io_ti: fix get_icount for two port adapters
USB: garmin_gps: fix memory leak on disconnect
...
Add modem-status-change wait queue to struct usb_serial_port that
subdrivers can use to implement TIOCMIWAIT.
Currently subdrivers use a private wait queue which may have been
released when waking up after device disconnected.
Note that we're adding a new wait queue rather than reusing the tty-port
one as we do not want to get woken up at hangup (yet).
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building a kernel for imx_v4_v5_defconfig with CONFIG_USB_ULPI disabled, results
in the following error:
arch/arm/mach-imx/built-in.o: In function 'pca100_init':
platform-mx2-emma.c:(.init.text+0x6788): undefined reference to 'otg_ulpi_create'
platform-mx2-emma.c:(.init.text+0x682c): undefined reference to 'mxc_ulpi_access_ops'
Fix this by providing a no-op definition of *otg_ulpi_create for the case when
CONFIG_USB_ULPI is not defined.
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull networking fixes from David Miller:
1) Fix ARM BPF JIT handling of negative 'k' values, from Chen Gang.
2) Insufficient space reserved for bridge netlink values, fix from
Stephen Hemminger.
3) Some dst_neigh_lookup*() callers don't interpret error pointer
correctly, fix from Zhouyi Zhou.
4) Fix transport match in SCTP active_path loops, from Xugeng Zhang.
5) Fix qeth driver handling of multi-order SKB frags, from Frank
Blaschka.
6) fec driver is missing napi_disable() call, resulting in crashes on
unload, from Georg Hofmann.
7) Don't try to handle PMTU events on a listening socket, fix from Eric
Dumazet.
8) Fix timestamp location calculations in IP option processing, from
David Ward.
9) FIB_TABLE_HASHSZ setting is not controlled by the correct kconfig
tests, from Denis V Lunev.
10) Fix TX descriptor push handling in SFC driver, from Ben Hutchings.
11) Fix isdn/hisax and tulip/de4x5 kconfig dependencies, from Arnd
Bergmann.
12) bnx2x statistics don't handle 4GB rollover correctly, fix from
Maciej Żenczykowski.
13) Openvswitch bug fixes for vport del/new error reporting, missing
genlmsg_end() call in netlink processing, and mis-parsing of
LLC/SNAP ethernet types. From Rich Lane.
14) SKB pfmemalloc state should only be propagated from the head page of
a compound page, fix from Pavel Emelyanov.
15) Fix link handling in tg3 driver for 5715 chips when autonegotation
is disabled. From Nithin Sujir.
16) Fix inverted test of cpdma_check_free_tx_desc return value in
davinci_emac driver, from Mugunthan V N.
17) vlan_depth is incorrectly calculated in skb_network_protocol(), from
Li RongQing.
18) Fix probing of Gobi 1K devices in qmi_wwan driver, and fix NCM
device mode backwards compat in cdc_ncm driver. From Bjørn Mork.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
inet: limit length of fragment queue hash table bucket lists
qeth: Fix scatter-gather regression
qeth: Fix invalid router settings handling
qeth: delay feature trace
tcp: dont handle MTU reduction on LISTEN socket
bnx2x: fix occasional statistics off-by-4GB error
vhost/net: fix heads usage of ubuf_info
bridge: Add support for setting BR_ROOT_BLOCK flag.
bnx2x: add missing napi deletion in error path
drivers: net: ethernet: ti: davinci_emac: fix usage of cpdma_check_free_tx_desc()
ethernet/tulip: DE4x5 needs VIRT_TO_BUS
isdn: hisax: netjet requires VIRT_TO_BUS
net: cdc_ncm, cdc_mbim: allow user to prefer NCM for backwards compatibility
rtnetlink: Mask the rta_type when range checking
Revert "ip_gre: make ipgre_tunnel_xmit() not parse network header as IP unconditionally"
Fix dst_neigh_lookup/dst_neigh_lookup_skb return value handling bug
smsc75xx: configuration help incorrectly mentions smsc95xx
net: fec: fix missing napi_disable call
net: fec: restart the FEC when PHY speed changes
skb: Propagate pfmemalloc on skb from head page only
...
Update irq handling code to notify all possible link status changes of
AB8500 and AB8505 to the ux500-musb glue driver. The additional event
codes will be used for pm-runtime implementation, and are defined in a
separate ux500-specific header.
This also modify the irq registration code to use devm_* helpers and
drop all non necessary fail path code.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
