Intel IDE-R devices are part of the Intel AMT management setup. They don't
have any special configuration registers or settings so the ata_generic
driver will support them fully.
Rather than add a huge table of IDs for each chipset and keep sending in
new ones this patch autodetects them.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Until now identifying that a device supports WRITE SAME(16) with the
UNMAP bit set has been black magic. Implement support for the SBC-3
Thin Provisioning VPD page and set the TPWS bit.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that libata provides proper cross-port EH exclusion. The SIDPR
locking added by commit 213373cf (ata_piix: fix locking around SIDPR
access) is no longer necessary. Remove it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In libata, the non-EH code paths should always take and release
ap->lock explicitly when accessing hardware or shared data structures.
However, once EH is active, it's assumed that the port is owned by EH
and EH methods don't explicitly take ap->lock unless race from irq
handler or other code paths are expected. However, libata EH didn't
guarantee exclusion among EHs for ports of the same host. IOW,
multiple EHs may execute in parallel on multiple ports of the same
controller.
In many cases, especially in SATA, the ports are completely
independent of each other and this doesn't cause problems; however,
there are cases where different ports share the same resource, which
lead to obscure timing related bugs such as the one fixed by commit
213373cf (ata_piix: fix locking around SIDPR access).
This patch implements exclusion among EHs of the same host. When EH
begins, it acquires per-host EH ownership by calling ata_eh_acquire().
When EH finishes, the ownership is released by calling
ata_eh_release(). EH ownership is also released whenever the EH
thread goes to sleep from ata_msleep() or explicitly and reacquired
after waking up.
This ensures that while EH is actively accessing the hardware, it has
exclusive access to it while allowing EHs to interleave and progress
in parallel as they hit waiting stages, which dominate the time spent
in EH. This achieves cross-port EH exclusion without pervasive and
fragile changes while still allowing parallel EH for the most part.
This was first reported by yuanding02@gmail.com more than three years
ago in the following bugzilla. :-)
https://bugzilla.kernel.org/show_bug.cgi?id=8223
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Reported-by: yuanding02@gmail.com
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add optional @ap argument to ata_wait_register() and replace msleep()
calls with ata_msleep() which take optional @ap in addition to the
duration. These will be used to implement EH exclusion.
This patch doesn't cause any behavior difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that DIPM can be used independently from HIPM, ata_piix can
support LPM too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Port multipliers can do DIPM on fan-out links fine. Implement support
for it. Tested w/ SIMG 57xx and marvell PMPs. Both the host and
fan-out links enter power save modes nicely.
SIMG 37xx and 47xx report link offline on SStatus causing EH to detach
the devices. Blacklisted.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The current LPM implementation has the following issues.
* Operation order isn't well thought-out. e.g. HIPM should be
configured after IPM in SControl is properly configured. Not the
other way around.
* Suspend/resume paths call ata_lpm_enable/disable() which must only
be called from EH context directly. Also, ata_lpm_enable/disable()
were called whether LPM was in use or not.
* Implementation is per-port when it should be per-link. As a result,
it can't be used for controllers with slave links or PMP.
* LPM state isn't managed consistently. After a link reset for
whatever reason including suspend/resume the actual LPM state would
be reset leaving ap->lpm_policy inconsistent.
* Generic/driver-specific logic boundary isn't clear. Currently,
libahci has to mangle stuff which libata EH proper should be
handling. This makes the implementation unnecessarily complex and
fragile.
* Tied to ALPM. Doesn't consider DIPM only cases and doesn't check
whether the device allows HIPM.
* Error handling isn't implemented.
Given the extent of mismatch with the rest of libata, I don't think
trying to fix it piecewise makes much sense. This patch reimplements
LPM support.
* The new implementation is per-link. The target policy is still
port-wide (ap->target_lpm_policy) but all the mechanisms and states
are per-link and integrate well with the rest of link abstraction
and can work with slave and PMP links.
* Core EH has proper control of LPM state. LPM state is reconfigured
when and only when reconfiguration is necessary. It makes sure that
LPM state is reset when probing for new device on the link.
Controller agnostic logic is now implemented in libata EH proper and
driver implementation only has to deal with controller specifics.
* Proper error handling. LPM config failure is attributed to the
device on the link and LPM is disabled for the link if it fails
repeatedly.
* ops->enable/disable_pm() are replaced with single ops->set_lpm()
which takes @policy and @hints. This simplifies driver specific
implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Link power management is about to be reimplemented. Prepare for it.
* Implement sata_link_scr_lpm().
* Drop static from ata_dev_set_feature() and make it available to
other libata files.
* Trivial whitespace adjustments.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Link power management related symbols are in confusing state w/ mixed
usages of lpm, ipm and pm. This patch cleans up lpm related symbols
and sysfs show/store functions as follows.
* lpm states - NOT_AVAILABLE, MIN_POWER, MAX_PERFORMANCE and
MEDIUM_POWER are renamed to ATA_LPM_UNKNOWN and
ATA_LPM_{MIN|MAX|MED}_POWER.
* Pre/postfixes are unified to lpm.
* sysfs show/store functions for link_power_management_policy were
curiously named get/put and unnecessarily complex. Renamed to
show/store and simplified.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This build error showed up in linux-next tag next-20100820 for ia64:
WARNING: vmlinux.o(.init.text+0x4a952): Section mismatch in reference from the function ata_init() to the function .exit.text:ata_sff_exit()
The function __init ata_init() references
a function __exit ata_sff_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __exit annotation of
ata_sff_exit() so it may be used outside an exit section.
Sure enough, dropping the __exit fixes the problem.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This change enables my x86 machine to recognize and talk to a
"Native 4K" SATA device.
When I started working on this, I didn't know Matthew Wilcox had
posted a similar patch 2 years ago:
http://git.kernel.org/?p=linux/kernel/git/willy/ata.git;a=shortlog;h=refs/heads/ata-large-sectors
Gwendal Grignou pointed me at the the above code and small portions of
this patch include Matthew's work. That's why Mathew is first on the
"Signed-off-by:". I've NOT included his use of a bitmap to determine
512 vs Native for ATA command block size - just used a simple table.
And bugs are almost certainly mine.
Lastly, the patch has been tested with a native 4K 'Engineering
Sample' drive provided by Hitachi GST.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Grant Grundler <grundler@google.com>
Reviewed-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently, sata_fsl, mv and nv call ata_qc_complete() multiple times
from their interrupt handlers to indicate completion of NCQ commands.
This limits the visibility the libata core layer has into how commands
are being executed and completed, which is necessary to support IRQ
expecting in generic way. libata already has an interface to complete
multiple commands at once - ata_qc_complete_multiple() which ahci and
sata_sil24 already use.
This patch updates the three drivers to use ata_qc_complete_multiple()
too and updates comments on ata_qc_complete[_multiple]() regarding
their usages with NCQ completions. This change not only provides
better visibility into command execution to the core layer but also
simplifies low level drivers.
* sata_fsl: It already builds done_mask. Conversion is straight
forward.
* sata_mv: mv_process_crpb_response() no longer checks for illegal
completions, it just returns whether the tag is completed or not.
mv_process_crpb_entries() builds done_mask from it and passes it to
ata_qc_complete_multiple() which will check for illegal completions.
* sata_nv adma: Similar to sata_mv. nv_adma_check_cpb() now just
returns the tag status and nv_adma_interrupt() builds done_mask from
it and passes it to ata_qc_complete_multiple().
* sata_nv swncq: It already builds done_mask. Drop unnecessary
illegal transition checks and call ata_qc_complete_multiple().
In the long run, it might be a good idea to make ata_qc_complete()
whine if called when multiple NCQ commands are in flight.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Saeed Bishara <saeed@marvell.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a scheleton for libata transport class.
All information is read only, exporting information from libata:
- ata_port class: one per ATA port
- ata_link class: one per ATA port or 15 for SATA Port Multiplier
- ata_device class: up to 2 for PATA link, usually one for SATA.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add WQ_MEM_RECLAIM flag which currently maps to WQ_RESCUER, mark
WQ_RESCUER as internal and replace all external WQ_RESCUER usages to
WQ_MEM_RECLAIM.
This makes the API users express the intent of the workqueue instead
of indicating the internal mechanism used to guarantee forward
progress. This is also to make it cleaner to add more semantics to
WQ_MEM_RECLAIM. For example, if deemed necessary, memory reclaim
workqueues can be made highpri.
This patch doesn't introduce any functional change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
libata depends on scsi_host_template for module reference counting and
sht's should be owned by each low level driver. During libahci split,
the sht was left with libahci.ko leaving the actual low level drivers
not reference counted. This made ahci and ahci_platform always
unloadable even while they're being actively used.
Fix it by defining AHCI_SHT() macro in ahci.h and defining a sht for
each low level ahci driver.
stable: only applicable to 2.6.35.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Pedro Francisco <pedrogfrancisco@gmail.com>
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Keep track of the link on the which the current request is in progress.
It allows support of links behind port multiplier.
Not all libata-sff is PMP compliant. Code for native BMDMA controller
does not take in accound PMP.
Tested on Marvell 7042 and Sil7526.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For some mysterious reason, certain hardware reacts badly to usual EH
actions while the system is going for suspend. As the devices won't
be needed until the system is resumed, ask EH to skip usual autopsy
and recovery and proceed directly to suspend.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: Stephan Diestelhorst <stephan.diestelhorst@amd.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the Intel Patsburg (PCH) SATA AHCI and RAID Controller
DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the Intel Patsburg (PCH) IDE mode SATA Controller DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 978c0666 (libata: Remove excess delay in the tf_load path)
removed ata_wait_idle() from ata_sff_tf_load() and via_tf_load().
This caused obscure detection problems in sata_sil.
https://bugzilla.kernel.org/show_bug.cgi?id=16606
The commit was pure performance optimization. Revert it for now.
Reported-by: Dieter Plaetinck <dieter@plaetinck.be>
Reported-by: Jan Beulich <JBeulich@novell.com>
Bisected-by: gianluca <gianluca@sottospazio.it>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ahci_do_softreset() compared the current time and deadline in reverse
when calculating timeout for SRST issue. The result is that if
@deadline is in future, SRST is issued with 0 timeout, which hasn't
caused any problem because it later waits for DRDY with the correct
timeout. If deadline is already exceeded by the time SRST is about to
be issued, the timeout calculation underflows and if the device
doesn't respond, timeout doesn't trigger for a _very_ long time.
Reverse the incorrect comparison order.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Gwendal Grignou <gwendal@google.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
x % 1 always evaluates to 0, which clearly isn't the intent. The
author probably had "% 2" or "& 1" in mind, and mispelled it.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove harmful BUG_ON() from ata_bmdma_qc_issue(),
as it casts too wide of a net and breaks sata_mv.
It also crashes the kernel while doing the BUG_ON().
There's already a WARN_ON_ONCE() further down to catch
the case of POLLING for a BMDMA operation.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
Fix DSM/TRIM commands in sata_mv (v2).
These need to be issued using old-school "BM DMA",
rather than via the EDMA host queue.
Since the chips don't have proper BM DMA status,
we need to be more careful with setting the ATA_DMA_INTR bit,
since DSM/TRIM often has a long delay between "DMA complete"
and "command complete".
GEN_I chips don't have BM DMA, so no TRIM for them.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
ata_qc_issue() BUG_ON()s on data commands w/o data, which may be
submitted via SG_IO. Be less of a drama queen and just trigger
WARN_ON_ONCE() and fail the command with AC_ERR_SYSTEM.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stefan Hübner <stefan.huebner@stud.tu-ilmenau.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dma_dwc_xfer_setup() returns an int and "dma_chan" needs to be signed
for the error handling to work.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
88SE9128 can do FBS and sets it in HOST_CAP but forgets to set FBSCP
in PORT_CMD. Implement AHCI_HFLAG_YES_FBS and apply it to 88SE9128.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Winbond W83759A controller is fully supported by pata_legacy driver
so remove no longer needed pata_winbond driver.
Leave PATA_WINBOND_VLB config option for compatibility reasons
and teach pata_legacy to preserve the old behavior of pata_winbond
driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit d62f5576 (pata_cmd64x: fix handling of address setup timings)
incorrectly called ata_timing_compute() on UDMA mode on 0 @UT leading
to devide by zero fault. Revert it until better fix is available.
This is reported in bko#16607 by Milan Kocian who also root caused it.
https://bugzilla.kernel.org/show_bug.cgi?id=16607
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-root-caused-by: Milan Kocian <milan.kocian@wq.cz>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some minor improvements in error handling, but overall it was mostly dead
code.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (226 commits)
ARM: 6323/1: cam60: don't use __init for cam60_spi_{flash_platform_data,partitions}
ARM: 6324/1: cam60: move cam60_spi_devices to .init.data
ARM: 6322/1: imx/pca100: Fix name of spi platform data
ARM: 6321/1: fix syntax error in main Kconfig file
ARM: 6297/1: move U300 timer to dynamic clock lookup
ARM: 6296/1: clock U300 intcon and timer properly
ARM: 6295/1: fix U300 apb_pclk split
ARM: 6306/1: fix inverted MMC card detect in U300
ARM: 6299/1: errata: TLBIASIDIS and TLBIMVAIS operations can broadcast a faulty ASID
ARM: 6294/1: etm: do a dummy read from OSSRR during initialization
ARM: 6292/1: coresight: add ETM management registers
ARM: 6288/1: ftrace: document mcount formats
ARM: 6287/1: ftrace: clean up mcount assembly indentation
ARM: 6286/1: fix Thumb-2 decompressor broken by "Auto calculate ZRELADDR"
ARM: 6281/1: video/imxfb.c: allow usage without BACKLIGHT_CLASS_DEVICE
ARM: 6280/1: imx: Fix build failure when including <mach/gpio.h> without <linux/spinlock.h>
ARM: S5PV210: Fix on missing s3c-sdhci card detection method for hsmmc3
ARM: S5P: Fix on missing S5P_DEV_FIMC in plat-s5p/Kconfig
ARM: S5PV210: Override FIMC driver name on Aquila board
ARM: S5PC100: enable FIMC on SMDKC100
...
Fix up conflicts in arch/arm/mach-{s5pc100,s5pv210}/cpu.c due to
different subsystem 'setname' calls, and trivial port types in
include/linux/serial_core.h
'make htmldocs' has a fatal error when processing libata.xml, as seen
below. The string "Example patterns:" (or any string with "example.*:"
in it AFAIK) causes some part of the doc generation tool chain to try to
produce an <informalexample> block without a beginning <para>, but
there is an ending </para> generated, which throws things out of kilter.
I don't even know where (what program) this is happening in.
I searched in docproc and xmlto and in some XML stylesheets without
finding anything. If anyone can give me pointers about this, please do.
Until this is fixed, let's just spell "Example" as "Sample"
and match up the double quotation marks while there.
Documentation/DocBook/libata.xml:6575: parser error : Opening and ending tag mismatch: programlisting line 6573 and para
</para><para>
^
Documentation/DocBook/libata.xml:6580: parser error : Opening and ending tag mismatch: para line 6575 and programlisting
</programlisting></informalexample>
^
unable to parse Documentation/DocBook/libata.xml
make[2]: *** [Documentation/DocBook/libata.html] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (55 commits)
workqueue: mark init_workqueues() as early_initcall()
workqueue: explain for_each_*cwq_cpu() iterators
fscache: fix build on !CONFIG_SYSCTL
slow-work: kill it
gfs2: use workqueue instead of slow-work
drm: use workqueue instead of slow-work
cifs: use workqueue instead of slow-work
fscache: drop references to slow-work
fscache: convert operation to use workqueue instead of slow-work
fscache: convert object to use workqueue instead of slow-work
workqueue: fix how cpu number is stored in work->data
workqueue: fix mayday_mask handling on UP
workqueue: fix build problem on !CONFIG_SMP
workqueue: fix locking in retry path of maybe_create_worker()
async: use workqueue for worker pool
workqueue: remove WQ_SINGLE_CPU and use WQ_UNBOUND instead
workqueue: implement unbound workqueue
workqueue: prepare for WQ_UNBOUND implementation
libata: take advantage of cmwq and remove concurrency limitations
workqueue: fix worker management invocation without pending works
...
Fixed up conflicts in fs/cifs/* as per Tejun. Other trivial conflicts in
include/linux/workqueue.h, kernel/trace/Kconfig and kernel/workqueue.c
Remove the current bio flags and reuse the request flags for the bio, too.
This allows to more easily trace the type of I/O from the filesystem
down to the block driver. There were two flags in the bio that were
missing in the requests: BIO_RW_UNPLUG and BIO_RW_AHEAD. Also I've
renamed two request flags that had a superflous RW in them.
Note that the flags are in bio.h despite having the REQ_ name - as
blkdev.h includes bio.h that is the only way to go for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Remove all the trivial wrappers for the cmd_type and cmd_flags fields in
struct requests. This allows much easier grepping for different request
types instead of unwinding through macros.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: avoid buffer overflow in pcmcia_setup_isa_irq
pcmcia: do not request windows if you don't need to
pcmcia: insert PCMCIA device resources into resource tree
pcmcia: export resource information to sysfs
pcmcia: use struct resource for PCMCIA devices, part 2
pcmcia: remove memreq_t
pcmcia: move local definitions out of include/pcmcia/cs.h
pcmcia: do not use io_req_t when calling pcmcia_request_io()
pcmcia: do not use io_req_t after call to pcmcia_request_io()
pcmcia: use struct resource for PCMCIA devices
pcmcia: clean up cs.h
pcmcia: use pcmica_{read,write}_config_byte
pcmcia: remove cs_types.h
pcmcia: remove unused flag, simplify headers
pcmcia: remove obsolete CS_EVENT_ definitions
pcmcia: split up central event handler
pcmcia: simplify event callback
pcmcia: remove obsolete ioctl
Conflicts in:
- drivers/staging/comedi/drivers/*
- drivers/staging/wlags49_h2/wl_cs.c
due to dev_info_t and whitespace changes
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
Make the following changes to prepare for NCQ command completion
update. Changes made by this patch don't cause any functional
difference.
* sata_fsl_host_intr(): rename the local variable qc_active to
done_mask as that's what it is.
* mv_process_crpb_response(): restructure if clause for easier update.
* nv_adma_interrupt(): drop unnecessary error variable.
* nv_swncq_sdbfis(): drop unnecessary nr_done and return 0 on success.
Typo fix.
* nv_swncq_dmafis(): drop unused return value and return void.
* nv_swncq_host_interrupt(): drop unnecessary return value handling.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Saeed Bishara <saeed@marvell.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SIDPR window registers are shared across ports and as each access is
done in two steps, accesses to different ports under EH may race.
This primarily is caused by incorrect host locking in EH context and
should be fixed by defining locking requirements for each EH operation
which can be used during EH and enforcing them but for now work around
the problem by adding a dedicated SIDPR lock and grabbing it for each
SIDPR access.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Mark Knecht <markknecht@gmail.com>
Reported-by: Paul Check <paul@thechecks.ca>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Take further advantage of the new glob_match() function to reduce
the blacklist size, this time making use of "character ranges" in
the patterns.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable use of hyphenated pattern ranges in glob_match(), similar to how
shell globbing works, and how developers might expect things to work.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 1529c69adc (ata_generic: implement ATA_GEN_* flags and force
enable DMA on MBP 7,1) implemented ATA_GEN_FORCE_DMA for forcing DMA
mode and applied it to CENATEK but forgot to remove the original hard
coded logic. This is removal of redundant logic and doesn't affect
correctness.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The below patch casts ATA_MAX_QUEUE to int because GCC will
give a warning message about the two different enum blocks:
CC drivers/ata/ahci.o
drivers/ata/ahci.c: In function 'ahci_init_one':
drivers/ata/ahci.c:1045:2: warning: comparison between 'enum <anonymous>' and 'enum <anonymous>'
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Adds support for the Samsung PATA controller. This driver is based
on the Libata subsystem and references the earlier patches sent for
IDE subsystem.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch enables the on-chip DWC SATA controller of the AppliedMicro
processor 460EX.
Signed-off-by: Rupjyoti Sarmah <rsarmah@appliedmicro.com>
Signed-off-by: Mark Miesfeld <mmiesfeld@appliedmicro.com>
Signed-off-by: Prodyut Hazarika <phazarika@appliedmicro.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Take further advantage of the new glob_match() function to reduce
the blacklist size. There are even more savings possible, but how
far do we want to go with this?
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Take advantage of the new glob_match() function to reduce the blacklist
size somewhat. There are further savings possible, but these are
the most obvious biggies.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Replace rudimentry pattern matching with more capable shell-style globbing.
This will enable shrinking ata_device_blacklist[] table in subsequent patches,
and helps with future editions to the table, such as matching only the end
of a firmware revision string etc..
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver is using platform_driver_probe() during initialization,
so ahci_driver.probe hook is never used.
But it causes the following (harmless, luckily) section mismatch:
WARNING: vmlinux.o(.data+0x2fb20): Section mismatch in reference
from the variable ahci_driver to the function .init.text:ahci_probe()
This patch removes the ahci_driver.probe assignment, thus fixes
the warning.
p.s. Note that there's another patch[1] from Rene Bolldorf that
tried to solve the same issue by __refdata annotation. __refdata
says that this reference is actually OK, but in fact it is not OK,
because dereferencing .probe() will cause problems. So the proper
fix is to remove the assignment.
[1] http://kerneltrap.org/mailarchive/linux-kernel/2010/3/18/4549547
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some AHCI implementations may use Vendor Specific HBA[A0h, FFh]
and/or Port[70h, 7Fh] registers to 'prepare' for initialization.
For that, the platform needs memory mapped address of AHCI registers.
This patch adds the 'mmio' argument and reorders the call to
platform init function.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata has two concurrency related limitations.
a. ata_wq which is used for polling PIO has single thread per CPU. If
there are multiple devices doing polling PIO on the same CPU, they
can't be executed simultaneously.
b. ata_aux_wq which is used for SCSI probing has single thread. In
cases where SCSI probing is stalled for extended period of time
which is possible for ATAPI devices, this will stall all probing.
#a is solved by increasing maximum concurrency of ata_wq. Please note
that polling PIO might be used under allocation path and thus needs to
be served by a separate wq with a rescuer.
#b is solved by using the default wq instead and achieving exclusion
via per-port mutex.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
IDE mode of MCP89 on MBP 7,1 doesn't set DMA enable bits in the BMDMA
status register. Make the following changes to work around the problem.
* Instead of using hard coded 1 in id->driver_data as class code
match, use ATA_GEN_CLASS_MATCH and carry the matched id in
host->private_data.
* Instead of matching PCI_VENDOR_ID_CENATEK, use ATA_GEN_FORCE_DMA
flag in id instead.
* Add ATA_GEN_FORCE_DMA to the id entry of MBP 7,1.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Cc: stable@kernel.org
Reported-by: Anders Østhus <grapz666@gmail.com>
Reported-by: Andreas Graf <andreas_graf@csgraf.de>
Reported-by: Benoit Gschwind <gschwind@gnu-log.net>
Reported-by: Damien Cassou <damien.cassou@gmail.com>
Reported-by: tixetsal@juno.com
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For yet unknown reason, MCP89 on MBP 7,1 doesn't work w/ ahci under
linux but the controller doesn't require explicit mode setting and
works fine with ata_generic. Make ahci ignore the controller on MBP
7,1 and let ata_generic take it for now.
Reported in bko#15923.
https://bugzilla.kernel.org/show_bug.cgi?id=15923
NVIDIA is investigating why ahci mode doesn't work.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Cc: stable@kernel.org
Reported-by: Anders Østhus <grapz666@gmail.com>
Reported-by: Andreas Graf <andreas_graf@csgraf.de>
Reported-by: Benoit Gschwind <gschwind@gnu-log.net>
Reported-by: Damien Cassou <damien.cassou@gmail.com>
Reported-by: tixetsal@juno.com
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In function ahci_store_em_buffer(), if the input (signed char*) buffer
contains negative data, the constructed 32-bit long message data may
be wrong.
Signed-off-by: Harry Zhang <harry.zhang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds a driver for a harddrive attached to PXA address and data bus.
Unlike pata_platform, this driver allows usage of PXA DMA controller, making the
transmission speed 3x higher.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The data in the cmd_block buffers may reach the main memory after the
writel() to the device ports. This patch introduces two calls to wmb()
to ensure the relative ordering.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Colin Tuckley <colin.tuckley@arm.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
cb->atapi.cdb is an array of 16 u8 elements. The call too memset()
would set the first part of the sge array to zero as well. It's not
a packed struct.
This one has been around for five years. I found it with Smatch. I
think the reason no one has seen it before is because we normally call
sil24_fill_sg() and that overwrites sge with proper information?
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 96d60303fd (ahci: Turn off DMA engines when there's no device)
implemented stopping DMA engines on empty ports but it used single
sampling of status registers to determine device presence which led to
disabling of DMA engines on occupied ports. Do it after all EH
actions are complete using device presence state determined by EH.
This avoids spurious disabling of DMA engines and simplifies the code.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: Marc Dionne <marc.c.dionne@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The sata_sil24 driver has six 16-bit registers that are initialised with
32-bit writes. This cause a kernel panic on ARM due to the unaligned
accesses which result.
This patch changes the accesses to the correct 16-bit ones.
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add Joseph Chan's explanation of the problem and workaround to the
VT6421 magic fix.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: implement on-demand HPA unlocking
libata: use the enlarged capacity after late HPA unlock
SCSI: implement sd_unlock_native_capacity()
libata-sff: trivial corrections to Kconfig help text
sata_nv: don't diddle with nIEN on mcp55
sata_via: magic vt6421 fix for transmission problems w/ WD drives
Implement ata_scsi_unlock_native_capacity() which will be called
through SCSI layer when block layer notices that partitions on a
device extend beyond the end of the device. It requests EH to unlock
HPA, waits for completion and returns the current device capacity.
This allows libata to unlock HPA on demand instead of having to decide
whether to unlock upfront. Unlocking on demand is safer than
unlocking by upfront because some BIOSes write private data to the
area beyond HPA limit. This was suggested by Ben Hutchings.
Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
After late HPA unlock, libata kept using the original capacity
ignoring the new larger native capacity. Enlarging device on the fly
doesn't cause any harm. Use the larger native capacity instead. This
will enable on-demand HPA unlocking.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On mcp55, nIEN gets stuck once set and liteon blueray rom iHOS104-08
violates ATA specification and fails to set I on D2H Reg FIS if nIEN
is set when the command was issued. When the other party is following
the spec, both devices can work fine but when the two flaws are put
together, they can't talk to each other.
mcp55 has its own IRQ masking mechanism and there's no reason to mess
with nIEN in the first place. Fix it by dropping nIEN diddling from
nv_mcp55_freeze/thaw().
This was originally reported by Cengiz. Although Cengiz hasn't
verified the fix yet, I could reproduce this problem and verfiy the
fix. Even if Cengiz is experiencing different or additional problems,
this patch is needed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Cengiz Günay <cgunay@emory.edu>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
vt6421 has problems talking to recent WD drives. It causes a lot of
transmission errors while high bandwidth transfer as reported in the
following bugzilla entry.
https://bugzilla.kernel.org/show_bug.cgi?id=15173
Joseph Chan provided the following fix. I don't have any idea what it
does but I can verify the issue is gone with the patch applied.
Signed-off-by: Tejun Heo <tj@kernel.org>
Originally-from: Joseph Chan <JosephChan@via.com.tw>
Reported-by: Jorrit Tijben <sjorrit@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Grant patches added an of mach table to struct device_driver. However,
while he changed the macio device code to use that, he left the match
table pointer in struct macio_driver and didn't update drivers to use
the "new" one, thus breaking the probing.
This completes the change by moving all drivers to setup the "new"
one, removing all traces of the old one, and while at it (since it
changes the exact same locations), I also remove two other duplicates
from struct driver which are the name and owner fields.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add dump_id libata.force parameter. If specified, libata dumps full
IDENTIFY data during device configuration. This is to aid debugging.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Larry Baker <baker@usgs.gov>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There are ATAPI devices which raise AN when hit by commands issued by
open(). This leads to infinite loop of AN -> MEDIA_CHANGE uevent ->
udev open() to check media -> AN.
Both ACS and SerialATA standards don't define in which case ATAPI
devices are supposed to raise or not raise AN. They both list media
insertion event as a possible use case for ATAPI ANs but there is no
clear description of what constitutes such events. As such, it seems
a bit too naive to export ANs directly to userland as MEDIA_CHANGE
events without further verification (which should behave similarly to
windows as it apparently is the only thing that some hardware vendors
are testing against).
This patch adds libata.atapi_an module parameter and disables ATAPI AN
by default for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Nick Bowler <nbowler@elliptictech.com>
Cc: David Zeuthen <david@fubar.dk>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make BMDMA optional depending on new config variable CONFIG_ATA_BMDMA.
In Kconfig, drivers are grouped into five groups - non-SFF native, SFF
w/ custom DMA interface, SFF w/ BMDMA, PIO-only SFF, and generic
fallback / legacy ones. Kconfig and Makefile are reorganized
according to the groups and ordered alphabetically inside each group.
ata_ioports.bmdma_addr and ata_port.bmdma_prd[_dma] are put into
CONFIG_ATA_BMDMA, as are all bmdma related ops, variables and
functions.
This increase the binary size slightly when BMDMA is enabled but on
both native-only and PIO-only configurations the size is slightly
reduced. Either way, the size difference is insignificant. This
change is more meaningful to signify the separation between SFF and
BMDMA and as a tool to verify the separation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that SFF and BMDMA are completely separate, sata_qstor and
pata_octeon_cf which inherit from ata_sff_port_ops don't need to worry
about BMDMA ops being called. Kill the dummy BMDMA ops.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Separate out ata_pci_bmdma_prepare_host() and ata_pci_bmdma_init_one()
from their SFF counterparts. SFF ones no longer try to initialize
BMDMA or set PCI master.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Separate out BMDMA irq handler from SFF irq handler. The misnamed
host_intr() functions are renamed to ata_sff_port_intr() and
ata_bmdma_port_intr(). Common parts are factored into
__ata_sff_port_intr() and __ata_sff_interrupt() and used by sff and
bmdma interrupt routines.
All BMDMA drivers now use ata_bmdma_interrupt() or
ata_bmdma_port_intr() while all non-BMDMA SFF ones use
ata_sff_interrupt() or ata_sff_port_intr().
For now, ata_pci_sff_init_one() uses ata_bmdma_interrupt() as it's
used by both SFF and BMDMA drivers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_sff_irq_clear() is BMDMA specific. Rename it to
ata_bmdma_irq_clear(), move it to ata_bmdma_port_ops and make
->sff_irq_clear() optional.
Note: ata_bmdma_irq_clear() is actually only needed by ata_piix and
possibly by sata_sil. This should be moved to respective low
level drivers later.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that BMDMA EH ops are separated out from SFF ops, mv5_ops doesn't
have to explicitly reset ->error_handler() and ->post_internal_cmd().
Drop them.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (49 commits)
libata-sff: separate out BMDMA qc_issue
libata-sff: prd is BMDMA specific
libata-sff: ata_sff_[dumb_]qc_prep are BMDMA specific
libata-sff: separate out BMDMA EH
libata-sff: port_task is SFF specific
libata-sff: ap->[last_]ctl are SFF specific
libata-sff: rename ap->ops->drain_fifo() to sff_drain_fifo()
libata-sff: introduce ata_sff_init/exit() and ata_sff_port_init()
libata-sff: clean up BMDMA initialization
libata-sff: clean up inheritance in several drivers
libata-sff: reorder SFF/BMDMA functions
sata_inic162x: kill PORT_PRD_ADDR initialization
libata: kill ATA_FLAG_DISABLED
libata-sff: kill unused prototype and make ata_dev_select() static
libata-sff: update bmdma host bus error handling
sata_mv: remove unnecessary initialization
sata_inic162x: inic162x is not dependent on CONFIG_ATA_SFF
pata_sch: use ata_pci_sff_init_one()
pata_sil680: Do our own exec_command posting
libata: Remove excess delay in the tf_load path
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
Separate out ata_bmdma_qc_issue() from ata_sff_qc_issue() such that
ata_sff_qc_issue() only deals with non-BMDMA SFF protocols (PIO and
nodata) while ata_bmdma_qc_issue() deals with the BMDMA protocols and
uses ata_sff_qc_issue() for non-DMA commands. All the users are
updated accordingly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
struct ata_prd and ap->prd are BMDMA specific. Add bmdma_ prefix to
them and move them inside CONFIG_ATA_SFF.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Both qc_prep functions deal only with BMDMA PRD setup and PIO only SFF
drivers don't need them. Rename to ata_bmdma_[dumb_]qc_prep() and
relocate.
All usages are renamed except for pdc_adma and sata_qstor. Those two
drivers are not BMDMA drivers and don't need to call BMDMA qc_prep
functions. Calls to ata_sff_qc_prep() in the two drivers are removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some of error handling logic in ata_sff_error_handler() and all of
ata_sff_post_internal_cmd() are for BMDMA. Create
ata_bmdma_error_handler() and ata_bmdma_post_internal_cmd() and move
BMDMA part into those.
While at it, change DMA protocol check to ata_is_dma(), fix
post_internal_cmd to call ap->ops->bmdma_stop instead of directly
calling ata_bmdma_stop() and open code hardreset selection so that
ata_std_error_handler() doesn't have to know about sff hardreset.
As these two functions are BMDMA specific, there's no reason to check
for bmdma_addr before calling bmdma methods if the protocol of the
failed command is DMA. sata_mv and pata_mpc52xx now don't need to set
.post_internal_cmd to ATA_OP_NULL and pata_icside and sata_qstor don't
need to set it to their bmdma_stop routines.
ata_sff_post_internal_cmd() becomes noop and is removed.
This fixes p3 described in clean-up-BMDMA-initialization patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
port_task is tightly bound to the standard SFF PIO HSM implementation.
Using it for any other purpose would be error-prone and there's no
such user and if some drivers need such feature, it would be much
better off using its own. Move it inside CONFIG_ATA_SFF and rename it
to sff_pio_task.
The only function which is exposed to the core layer is
ata_sff_flush_pio_task() which is renamed from ata_port_flush_task()
and now also takes care of resetting hsm_task_state to HSM_ST_IDLE,
which is possible as it's now specific to PIO HSM.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ap->[last_]ctl are specific to SFF controllers. Put them inside
CONFIG_ATA_SFF and move initialization into ata_sff_port_init().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In preparation of proper SFF/BMDMA separation, introduce
ata_sff_init/exit() and ata_sff_port_init(). These functions
currently don't do anything.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When BMDMA initialization failed or BMDMA was not available for
whatever reason, bmdma_addr was left at zero and used as an indication
that BMDMA shouldn't be used. This leads to the following problems.
p1. For BMDMA drivers which don't use traditional BMDMA register,
ata_bmdma_mode_filter() incorrectly inhibits DMA modes. Those
drivers either have to inherit from ata_sff_port_ops or clear
->mode_filter explicitly.
p2. non-BMDMA drivers call into BMDMA PRD table allocation. It
doesn't actually allocate PRD table if bmdma_addr is not
initialized but is still confusing.
p3. For BMDMA drivers which don't use traditional BMDMA register, some
methods might not be invoked as expected (e.g. bmdma_stop from
ata_sff_post_internal_cmd()).
p4. SFF drivers w/ custom DMA interface implement noop BMDMA ops
worrying libata core might call into one of them.
These problems are caused by the muddy line between SFF and BMDMA and
the assumption that all BMDMA controllers initialize bmdma_addr.
This patch fixes p1 and p2 by removing the bmdma_addr assumption and
moving prd allocation to BMDMA port start. Later patches will fix the
remaining issues.
This patch improves BMDMA initialization such that
* When BMDMA register initialization fails, falls back to PIO instead
of failing. ata_pci_bmdma_init() never fails now.
* When ata_pci_bmdma_init() falls back to PIO, it clears
ap->mwdma_mask and udma_mask instead of depending on
ata_bmdma_mode_filter(). This makes ata_bmdma_mode_filter()
unnecessary thus resolving p1.
* ata_port_start() which actually is BMDMA specific is moved to
ata_bmdma_port_start(). ata_port_start() and ata_sff_port_start()
are killed.
* ata_sff_port_start32() is moved and renamed to
ata_bmdma_port_start32().
Drivers which no longer call into PRD table allocation are...
pdc_adma, sata_inic162x, sata_qstor, sata_sx4, pata_cmd640 and all
drivers which inherit from ata_sff_port_ops.
pata_icside sets ->port_start to ATA_OP_NULL as it doesn't need PRD
but is a BMDMA controller and doesn't have custom port_start like
other such controllers.
Note that with the previous patch which makes all and only BMDMA
drivers inherit from ata_bmdma_port_ops, this change doesn't break
drivers which need PRD table.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
1. pata_cmd640 is PIO only. Inherit from sff.
2. pata_macio is BMDMA. Inherit from bmdma and drop explicit
bmdma_mode_filter() setting.
3. In sata_mv, unlike mv5, mv6 is BMDMA. Inherit from bmdma and
don't clear ->post_internal_cmd().
4. bf54x and icside are quasi-BMDMA controllers which don't use the
standard BMDMA registers so they don't initialize bmdma_addr and
inherit from sff to avoid the default mode_filter which disables
DMA modes if bmdma_addr is not initialized.
For 2 and 3, this patch makes the drivers explicitly specify
->mode_filter to ATA_OP_NULL while inheriting from ata_bmdma_port_ops.
These will be removed by the next patch.
This patch makes all and only BMDMA drivers inherit from
ata_bmdma_port_ops to ease further SFF/BMDMA separation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reorder functions such that SFF and BMDMA functions are grouped.
While at it, s/BMDMA/SFF in a few comments where it actually meant
SFF.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_inic162x doesn't use PRD anymore. No need to initialize it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ATA_FLAG_DISABLED is only used by drivers which don't use
->error_handler framework and is largely broken. Its only meaningful
function is to make irq handlers skip processing if the flag is set,
which is largely useless and even harmful as it makes those ports more
likely to cause IRQ storms.
Kill ATA_FLAG_DISABLED and makes the callers disable attached devices
instead. ata_port_probe() and ata_port_disable() which manipulate the
flag are also killed.
This simplifies condition check in IRQ handlers. While updating IRQ
handlers, remove ap NULL check as libata guarantees consecutive port
allocation (unoccupied ports are initialized with dummies) and
long-obsolete ATA_QCFLAG_ACTIVE check (checked by ata_qc_from_tag()).
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_irq_on() was renamed to ata_sff_irq_on() and exported a while ago
but prototype for the original function lingered in
drivers/ata/libata.h. Kill it. Also, ata_dev_select() is only used
inside drivers/ata/libata-sff.c. Make it static.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Clearing IRQ from ata_sff_error_handler() is necessary only when the
port is gonna be thawed before performing EH actions and some
controllers don't like being accessed after certain failure modes
until they're reset. Clear IRQ iff the port is being thawed.
* When the controller succesfully indicated bus error, the point of
thawing doesn't matter. Move thawing inside bmdma part of EH. This
is a bit ugly but will ease code reorganization later.
* Remove the unneeded ata_sff_sync().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_mv initializes unused ioports fields including bmdma_addr to
NULL. As later changes will conditionalize BMDMA, this makes sata_mv
unnecessarily dependent on BMDMA. Remove the unnecessary
initialization.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_inic162x no longer uses SFF interface. Move it out of
CONFIG_ATA_SFF.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
pata_sch is standard SFF. No reason to open code init. Use
ata_pci_sff_init_one() instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use our own mmio area to avoid PCI posting. This avoids the rather slow
paranoid implementation in the default handler.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We don't need to stall and wait after loading the task file and before
issuing a command, so don't do it. This shows up on profiles and is not
needed.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_nv was incorrectly using ata_host_activate() instead of
ata_pci_sff_activate_host() leading to IRQ assignment failure in
legacy mode. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Robert Hancock <hancockr@shaw.ca>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
page_mapping() check this via VM_BUG_ON(PageSlab(page)) so we bug here
with the according debuging turned on.
Future TODO: replace this with a flush_dcache_page_for_pio() API
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
cmd640_hardware_init() reads CFR but doesn't use the value read...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now, with the introduction of the sff_set_devctl() method, we can
use it in sff_irq_on() method too -- that way its implementations
in 'pata_bf54x' and 'pata_scc' become virtually identical to
ata_sff_irq_on(). The sff_irq_on() method now becomes quite
superfluous, and the only reason not to remove it completely is
the existence of the 'pata_octeon_cf' driver which implements it
as an empty function. Just make the method optional then, with
ata_sff_irq_on() becoming generic taskfile-bound function, still
global for the 'pata_bf54x' driver to be able to call it from its
thaw() and postreset() methods.
While at it, make the sff_irq_on() method and ata_sff_irq_on() return
'void' as the result is always ignored anyway.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The set of libata's taskfile access methods is clearly incomplete as
it lacks a method to write to the device control register -- which
forces drivers like 'pata_bf54x' and 'pata_scc' to implement more
"high level" (and more weighty) methods like freeze() and postreset().
So, introduce the optional sff_set_devctl() method which the drivers
only have to implement if the standard iowrite8() can't be used (just
like the existing sff_check_altstatus() method) and make use of it
in the freeze() and postreset() method implementations (I could also
have used it in softreset() method but it also reads other taskfile
registers without using tf_read() making that quite pointless);
this makes freeze() method implementations in the 'pata_bf54x' and
'pata_scc' methods virtually identical to ata_sff_freeze(), so we
can get rid of them completely.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add "em_buffer" attribute for SATA AHCI hosts to provide a way for
userland to access AHCI EM (enclosure management) buffer directly if the
host supports EM.
AHCI driver should support SGPIO EM messages. However the SATA/AHCI
specs did not define the SGPIO message format filled in EM buffer.
Different HW vendors may have different definitions. The mainly purpose
of this attribute is to solve this issue by allowing HW vendors to
provide userland drivers and tools for their SGPIO initiators.
Signed-off-by: Harry Zhang <harry.zhang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Detect enclosure management message type automatically at driver
initialization, instead of using module parameter "ahci_em_messages".
Signed-off-by: Harry Zhang <harry.zhang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The device control register exists and its address is set by scc_setup_ports(),
hence the check is useless...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
... since, of course, it's not used outside this driver.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use __ratelimit() instead of its own private rate limit implementation.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There are some SATA devices which take relatively long to get out of
0xff status after reset. In libata, this timeout is determined by
ATA_TMOUT_FF_WAIT. Quantum GoVault is the worst requring about 2s for
reliable detection. However, because 2s 0xff timeout can introduce
rather long spurious delay during boot, libata has been compromising
at the next longest timeout of 800ms for HHD424020F7SV00 iVDR drive.
Now that parallel scan is in place for common drivers, libata can
afford 2s 0xff timeout. Use 2s 0xff timeout if parallel scan is
enabled.
Please note that the chance of spurious wait is pretty slim w/ working
SCR access so this will only affect SATA controllers w/o SCR access
which isn't too common these days.
Please read the following thread for more information on the GoVault
drive.
http://thread.gmane.org/gmane.linux.ide/14545/focus=14663
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In 2009, While running "cache read" performance test of drives behind
SII PMP we encountered a "all 5 drives" timeout on more than 30% of the
machines under test. This patch reduces the rate by a factor of about 70.
Low enough that we didn't care to further investigate the issue.
Performance impact with any sort of "normal" use was ~2%+ CPU and less
than 1% throughput degradation. Worst case impact (cached read) was
6% IOPS reduction. This is with NCQ off (q=1) but I believe FIS based
switching enabled in the SATA driver.
The patch disables "Early ACK" in the 3726 port multiplier.
"Early ACK" is issued when device sends a FIS to the host (via PMP)
and the PMP sends an ACK immediately back to the device - well before
the host gets the response. Under worst case IOPs load (cached read
test) and more than 2 PMPs connected to a 4-port SATA controller,
I suspect the time to service all of the PMPs is exceeding the PMPs
ability to keep track of outstanding FIS it owes the Host. Reducing
the number of PMPs to 2 (or 1) reduces the frequency by several orders
of magnitude. Kudos to Gwendal for initial debugging of this issue.
[Any errors in the description are mine, not his.]
Patch is currently in production on Google servers.
Signed-off-by: Grant Grundler <grundler@google.com>
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It turns out different generations of MCPs have differing quirks.
* MCP 65-73 : FPDMA AA broken, lies about PMP support, forgets to report NCQ
* MCP 77-79 : FPDMA AA broken, lies about PMP support
* MCP 89 : FPDMA AA broken
Instead of turngin off FPDMA AA on all NVIDIAs, implement
HFLAG_NO_FPDMA_AA, define additional board IDs and apply necessary
quirks.
This fixes bko#15481 and the list of quirks is verified by Peer Chen.
http://bugzilla.kernel.org/show_bug.cgi?id=15481
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I've prepared a totally simple patch that, if I did it and measured it
correctly, reduces the text size as of the ppc-6xx-size command of
pata-mpc52xx by more than 10%, by reducing the rodata size from 0x4a4
to 0x17e bytes. This is simply done by changing the data types of the
ATA timing constants.
If you are interested at all, and it's worth the trouble, here the
details:
ppc-6xx-size:
text data bss dec hex filename
old: 6532 1068 0 7600 1db0 pata-mpc52xx.o
new: 5718 1068 0 6786 1a82 pata-mpc52xx.o
The (assembler) code itself doesn't really change very much. I double
checked the final results inside mpc52xx-ata-apply-timings() and they
match. The driver is still working fine of course.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ahci over time has grown a number of board IDs and it's a bit of mess
right now. Clean it up such that,
* board_id_* now live in a separate enum board_ids and numbers are
assigned automatically.
* Board IDs assigned to features are separated from the ones assigned
to specific implementations and both are ordered alphabetically.
* For NV MCPs, define per-generation alias board_ids and assign
matching aliases in the pci id table. This makes mcp_linux, 67-73
use board_ahci_mcp65 instead of board_ahci_yesncq. Both are
identical in content.
* Kill now unused board_ahci_nopmp and board_ahci_yesncq.
This patch doesn't cause any functional change but will make future
changes to board_ids and quirks much less painful.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
According to section 10.3.1 of the AHCI spec, PxCMD.ST must not be set
unless there's a device attached. Following this saves us a measurable
quantity of power and does not impair hotplug support. Based on a patch
by Kristen Carlson Accardi.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This can be used for AHCI-compatible interfaces implemented inside
System-On-Chip solutions, or AHCI devices connected via localbus.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch should contain no functional changes, just moves code
around.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Factor out some ahci_em_messages handling code from ahci_init_one().
We would like to reuse it for non-PCI devices.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce ahci_pci_print_info() that now handles PCI stuff.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Move PCI stuff into ahci_pci_init_controller().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
To make the function bus-independand we have to get rid of
"struct pci_dev *", so let's pass just "struct devce *".
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Move PCI stuff into ahci_pci_reset_controller().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
To make the function generic we have to get rid of "struct pci_dev *",
so let's pass just a "struct devce *".
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make ahci_save_initial_config() a bit more generic by introducing
force_port_map and mask_port_map arguments.
Move PCI stuff into ahci_pci_save_initial_config().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently the driver uses host->iomap to store all the iomapped BARs
of a PCI device (while AHCI devices actually use just a single memory
window).
We're going to teach AHCI to work with non-PCI buses, so there are two
options to make this work:
1. "fake" host->iomap array for non-PCI devices, and place the needed
address at iomap[AHCI_PCI_BAR];
2. Get rid of host->iomap usage, instead introduce a private mmio
field.
This patch implements the second option.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Instead of the old pcmcia_request_irq() interface, drivers may now
choose between:
- calling request_irq/free_irq directly. Use the IRQ from *p_dev->irq.
- use pcmcia_request_irq(p_dev, handler_t); the PCMCIA core will
clean up automatically on calls to pcmcia_disable_device() or
device ejection.
- drivers still not capable of IRQF_SHARED (or not telling us so) may
use the deprecated pcmcia_request_exclusive_irq() for the time
being; they might receive a shared IRQ nonetheless.
CC: linux-bluetooth@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: linux-usb@vger.kernel.org
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch fixes the bad hashes for one Kingston and one Transcend card.
Thanks to komuro for pointing this out.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds idstrings for Kingston 1GB/4GB and Transcend 4GB/8GB.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
blk_abort_request() expectes queue lock to be held by the caller.
Grab it before calling the function.
Lack of this synchronization led to infinite loop on corrupt
q->timeout_list.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some BIOSes don't configure HPA during boot but do so while resuming.
This causes harddrives to shrink during resume making libata detach
and reattach them. This can be worked around by unlocking HPA if old
size equals native size.
Add ATA_DFLAG_UNLOCK_HPA so that HPA unlocking can be controlled
per-device and update ata_dev_revalidate() such that it sets
ATA_DFLAG_UNLOCK_HPA and fails with -EIO when the above condition is
detected.
This patch fixes the following bug.
https://bugzilla.kernel.org/show_bug.cgi?id=15396
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Oleksandr Yermolenko <yaa.bta@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Crucial said,
Thank you for contacting us. We know that with our M225 line of SSDs
you sometimes need to disable NCQ (native command queuing) to avoid
just the type of errors you're seeing. Our recommendation for the
M225 is to add libata.force=noncq to your Linux kernel boot options,
under the kernel ATA library option.
I have sent your feedback to the engineers working on the C300, and
asked them to please pass it on to the firmware team. I have been
notified that they are in the process of testing and finalizing a
new firmware version, that you can expect to see released around the
end of April. We’ll keep you posted as to when it will be available
for download.
So, turn off NCQ on the drive w/ the current firmware revision.
Reported in the following bug.
https://bugzilla.kernel.org/show_bug.cgi?id=15573
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: lethalwp@scarlet.be
Reported-by: Luke Macken <lmacken@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On configurations where IRQ line is shared with a different
controller, spurious IRQs may happen continuously. The message was
put there primarily for debugging anyway. Kill it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
When using VT6410/6415/6330 chips on some VIA's platforms, the HDD
connection to VT6410/6415/6330 cannot be detected.
It is because the driver detects wrong via_isa_bridge ID, and then
causes this issue to happen.
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 27943620cb introduced spurious
IRQ handling but it has a race condition where valid completion can be
lost while trying to clear spurious IRQ leading to occassional command
timeouts.
This patch improves SFF interrupt handler such that
1. Once BMDMA HSM is stopped, the condition is never considered
spurious. As there's no way to resume stopped BMDMA HSM, if device
status doesn't agree with BMDMA status, the only way out is
aborting the command (otherwise, it will just end up timing out).
2. ap->ops->sff_check_status() can be safely called to clear spurious
device IRQ as it atomically returns completion status but BMDMA IRQ
status can't be cleared in safe way if command is in flight. After
a spurious IRQ, call ap->ops->sff_irq_clear() only if the
respective device is idle and retry completion if
sff_check_status() indicates command completion.
Please note that ata_piix uses bmdma_status for sff_irq_check() and #2
won't weaken spurious IRQ handling even with in-flight command because
if bmdma_status indicates IRQ pending but device status is not on
spurious check, the next IRQ handler invocation will abort the command
due to #1.
This fixes bko#15537.
https://bugzilla.kernel.org/show_bug.cgi?id=15537
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Andrew Benton <b3nton@gmail.com>
Cc: Petr Uzel <petr.uzel@centrum.cz>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
pp->active_link is not reliable when FBS is enabled.
Both PORT_SCR_ACT and PORT_CMD_ISSUE should be checked
because mixed NCQ and non-NCQ commands may be in flight.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
HP is recycling both DMI_PRODUCT_NAME and DMI_BIOS_VERSION making
ahci_broken_suspend() trigger for later products which are not
affected by the original problems. Match BIOS date instead of version
and add references to bko's so that full information can be found
easier later.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=15462
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: tigerfishdaisy@gmail.com
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
bko#15481 shows that we're missing some NVIDIA ahci PCI IDs. Peer
Chen confirms that IDs 0x580-0x58f are reserved for cases where Linux
ID option is selected in the BIOS and are only used for mcp65-73. Add
0x0581-0x058f.
http://bugzilla.kernel.org/show_bug.cgi?id=15481
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (38 commits)
sata_via: Delay on vt6420 when starting ATAPI DMA write
ata: Detect Delkin Devices compact flash
pata_efar: Enable parallel scanning
pata_atiixp: enable parallel scan
[libata] pata_atiixp: add locking for parallel scanning
[libata] pata_efar: add locking for parallel scanning
libata: Pass host flags into the pci helper
[libata] pata_marvell: CONFIG_AHCI is really CONFIG_SATA_AHCI
libata: Allow pata_legacy to be built on non-ISA but PCI systems
pata_pdc202xx_old: fix UDMA mode for PDC2026x chipsets
pata_pdc202xx_old: fix UDMA mode for Promise UDMA33 cards
[libata] pata_at91: fix backslash-continued string
pata_via: store UDMA masks in via_isa_bridges table
pata_via: fix address setup timings underlocking
pata_serverworks: fix error message
pata_serverworks: fix PIO setup for the second channel
pata_efar: fix secondary port support
pata_cypress: fix PIO timings underclocking
pata_cs5535: use correct values for PIO1 and PIO2 data timings
pata_cmd64x: remove unused definitions
...
When writing a disc on certain lite-on dvd-writers (also rebadged
as optiarc/LG/...) connected to a vt6420, the ATAPI CDB ends
up in the datastream and on the disc, causing silent corruption.
Delaying between sending the CDB and starting DMA seems to
prevent this.
I do not know if there are burners that do not suffer from
this, but the patch should be safe for those as well.
There are many reports of this issue, but AFAICT no solution was
found before. For example:
http://lkml.indiana.edu/hypermail/linux/kernel/0802.3/0561.html
Signed-off-by: Bart Hartgers <bart.hartgers@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Again originally proposed by Bartlomiej but this does it by using the
generic helper logic instead.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This was originally proposed by Bartlomiej but as a device specific
expansion of the init_one function rather than making the helper more
generic.
Enable the parallel scan via the generic flags.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is similar change as commit 60c3be3 for ata_piix host driver
and while pata_atiixp doesn't enable parallel scan yet the race
could probably also be triggered by requesting re-scanning of both
ports at the same time using SCSI sysfs interface.
[Ported to current tree without other patch dependancies by Alan Cox]
Original is
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This one is
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add clearing of UDMA enable bit also for PIO modes and then add
extra locking for parallel scanning.
This is similar change as commit 60c3be3 for ata_piix host driver
and while pata_efar doesn't enable parallel scan yet the race could
probably also be triggered by requesting re-scanning of both ports
at the same time using SCSI sysfs interface.
[Ported to current kernel without other patch dependancies by
Alan Cox]
Original is
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This one is
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This allows parallel scan and the like to be set without having to stop
using the existing full helper functions. This patch merely adds the argument
and fixes up the callers. It doesn't undo the special cases already in the
tree or add any new parallel callers.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The marvell driver comtains a fallback to ahci for the sata ports
which is incorrectly checked as CONFIG_AHCI while the only AHCI config
item is actually called SATA_AHCI (which also sounds sensible
considering it's a fallback for the sata ports).
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is needed for some unsupported hardware setups on strange 64bit
mainboards where crazy stuff has been done like putting flash ata adapters
on the LPC bus, or where the real hardware is hidden/confused.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PDC2026x chipsets need the same treatment as PDC20246 one.
This is completely untested but will hopefully fix UDMA issues
that people have been reporting against pata_pdc202xx_old for
the last couple of years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On Monday 04 January 2010 02:30:24 pm Russell King wrote:
> Found the problem - getting rid of the read of the alt status register
> after the command has been written fixes the UDMA CRC errors on write:
>
> @@ -676,7 +676,8 @@ void ata_sff_exec_command(struct ata_port *ap, const struct
> ata_taskfile *tf)
> DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
>
> iowrite8(tf->command, ap->ioaddr.command_addr);
> - ata_sff_pause(ap);
> + ndelay(400);
> +// ata_sff_pause(ap);
> }
> EXPORT_SYMBOL_GPL(ata_sff_exec_command);
>
>
> This rather makes sense. The PDC20247 handles the UDMA part of the
> protocol. It has no way to tell the PDC20246 to wait while it suspends
> UDMA, so that a normal register access can take place - the 246 ploughs
> on with the register access without any regard to the state of the 247.
>
> If the drive immediately starts the UDMA protocol after a write to the
> command register (as it probably will for the DMA WRITE command), then
> we'll be accessing the taskfile in the middle of the UDMA setup, which
> can't be good. It's certainly a violation of the ATA specs.
Fix it by adding custom ->sff_exec_command method for UDMA33 chipsets.
Debugged-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* store UDMA masks in via_isa_bridges[] and while at it make "flags"
field to be u8 instead of u16
* convert the driver to use UDMA masks from via_isa_bridges[]
* remove no longer needed VIA_UDMA* defines
Make some minor documentation and CodingStyle fixes while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Correct via_do_set_mode() documentation while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Timing registers should be programmed with the desired number of clocks
minus one clock.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There shouldn't be any problems with it as IDE cs5535 host driver
has been using those values for years and they match values given
in the (publicly available) datasheet.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
s/ARTIM2/ARTTIM23/ in cmd648_bmdma_stop() while at it
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Clear the primary channel pending interrupt bit
instead of the reserved one.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Account for the requirements of the DMA mode currently used
by the pair device.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use standard cycle timing for CFA PIO5 and PIO6 modes.
Based on commit 74638c8 for IDE subsystem.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Before only the timings for master were set. Datasheet can be found
here: ftp://ftp.vtbridge.org/Docs/Storage/DS_VT6421A_100_CCPL.PDF
Surprisingly, a slave drive works without this patch. According to the
datasheet, the controller by default derives the DMA mode from the
Set Features command issued to a drive. Not sure about the PIO
timings, though. The real problem is that the timings for the master
effectively are the ones tuned for the slave. If these support
different UDMA-settings, there is trouble, especially when the slave
supports a higher UDMA than the master.
Anyhow, using the same mechanism for both master and slave seems like
a good idea.
Signed-off-by: Bart Hartgers <bart.hartgers@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make some variables in ahci and a function in pata_pcmcia static, as found
using sparse.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Traditional IDE interface sucks in that it doesn't have a reliable IRQ
pending bit, so if the controller raises IRQ while the driver is
expecting it not to, the IRQ won't be cleared and eventually the IRQ
line will be killed by interrupt subsystem. Some controllers have
non-standard mechanism to indicate IRQ pending so that this condition
can be detected and worked around.
This patch adds an optional operation ->sff_irq_check() which will be
called for each port from the ata_sff_interrupt() if an unexpected
interrupt is received. If the operation returns %true,
->sff_check_status() and ->sff_irq_clear() will be cleared for the
port. Note that this doesn't mark the interrupt as handled so it
won't prevent IRQ subsystem from killing the IRQ if this mechanism
fails to clear the spurious IRQ.
This patch also implements ->sff_irq_check() for ata_piix. Note that
this adds slight overhead to shared IRQ operation as IRQs which are
destined for other controllers will trigger extra register accesses to
check whether IDE interrupt is pending but this solves rare screaming
IRQ cases and for some curious reason also helps weird BIOS related
glitch on Samsung n130 as reported in bko#14314.
http://bugzilla.kernel.org/show_bug.cgi?id=14314
* piix_base_ops dropped as suggested by Sergei.
* Spurious IRQ detection doesn't kick in anymore if polling qc is in
progress. This provides less protection but some controllers have
possible data corruption issues if the wrong register is accessed
while a command is in progress.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Johannes Stezenbach <js@sig21.net>
Reported-by: Hans Werner <hwerner4@gmx.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
host->ports[i] is never NULL if i < host->n_ports and non-NULL return
from ata_qc_from_tag() guarantees that the returned qc is active.
Drop unnecessary tests.
Superflous () dropped as suggested by Sergei.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Describe UDMA timing bits 18-20 and 21 separately; add a note to bit
31 about it being meaningful for PIO only. Reformat the whole comment,
while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There's no need to clear the fast interrupt bit in hpt366_set_mode()
since we're doing it in hpt366_init_chipset() already.
While at it, rename 'addr1' local variable to 'addr' and
exclude 'ap->port_no' from its calculation as HPT36x are
single-channel-per-function chips.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As these drivers' set_piomode() and set_dmamode() methods are almost
identical, factor out the common hpt{37x|3x2n}_set_mode() function
to be called by both of them, the same as in 'pata_hpt366' driver.
This results in ~5% decrease in the 'pata_hpt37x' driver binary
size and in ~4% decrease in the 'pata_hpt3x2n' driver binary size
(as measured on x86-32).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The UltraDMA Tss timing must be stretched with ATA clock of 66 MHz, but the
driver only does this when PCI clock is 66 MHz, whereas it always programs
DPLL clock (which is used as the ATA clock) to 66 MHz.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use ATA_DMA_* constants instead of the bare numbers for the BMIDE registers.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: replace acpi_integer by u64
ACPICA: Update version to 20100121.
ACPICA: Remove unused uint32_struct type
ACPICA: Disassembler: Remove obsolete "Integer64" field in parse object
ACPICA: Remove obsolete ACPI_INTEGER (acpi_integer) type
ACPICA: Predefined name repair: fix NULL package elements
ACPICA: AcpiGetDevices: Eliminate unnecessary _STA calls
ACPICA: Update all ACPICA copyrights and signons to 2010
ACPICA: Update for new gcc-4 warning options
* 'for-2.6.34' of git://git.kernel.dk/linux-2.6-block: (38 commits)
block: don't access jiffies when initialising io_context
cfq: remove 8 bytes of padding from cfq_rb_root on 64 bit builds
block: fix for "Consolidate phys_segment and hw_segment limits"
cfq-iosched: quantum check tweak
blktrace: perform cleanup after setup error
blkdev: fix merge_bvec_fn return value checks
cfq-iosched: requests "in flight" vs "in driver" clarification
cciss: Fix problem with scatter gather elements in the scsi half of the driver
cciss: eliminate unnecessary pointer use in cciss scsi code
cciss: do not use void pointer for scsi hba data
cciss: factor out scatter gather chain block mapping code
cciss: fix scatter gather chain block dma direction kludge
cciss: simplify scatter gather code
cciss: factor out scatter gather chain block allocation and freeing
cciss: detect bad alignment of scsi commands at build time
cciss: clarify command list padding calculation
cfq-iosched: rethink seeky detection for SSDs
cfq-iosched: rework seeky detection
block: remove padding from io_context on 64bit builds
block: Consolidate phys_segment and hw_segment limits
...
Except for SCSI no device drivers distinguish between physical and
hardware segment limits. Consolidate the two into a single segment
limit.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The block layer calling convention is blk_queue_<limit name>.
blk_queue_max_sectors predates this practice, leading to some confusion.
Rename the function to appropriately reflect that its intended use is to
set max_hw_sectors.
Also introduce a temporary wrapper for backwards compability. This can
be removed after the merge window is closed.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Mike Cui reported that his system with an NVIDIA MCP79 (aka MCP7A)
chipset stopped working with 2.6.32. The problem appears to be that
2.6.32 now enables the FPDMA auto-activate optimization in the ahci
driver. The drive works fine with this enabled on an Intel AHCI so
this appears to be a chipset bug. Since MCP79 is a fairly recent
NVIDIA chipset and we don't have any info on whether any other NVIDIA
chipsets have this issue, disable FPDMA AA optimization on all NVIDIA
AHCI controllers for now.
Should address http://bugzilla.kernel.org/show_bug.cgi?id=14922
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
While-we-investigate-issue-this-patch-looks-good-to-me-by:
Prajakta Gudadhe <pgudadhe@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some comments misspell "should" or "shouldn't"; this fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
flush_dcache_page() must be called after (!ATA_TFLAG_WRITE) the
data copying to avoid D-cache aliasing with user space or I-D cache
coherency issues (when reading data from an ATA device using PIO,
the kernel dirties the D-cache but there is no flush_dcache_page()
required on Harvard architectures).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acer G725 shares the same suspend problem with the HP laptops which
lose ATA devices on resume. New firmware which fixes the problem is
already available. Add G725 with old firmwares to the broken suspend
list.
This problem has been reported in bko#15104.
http://bugzilla.kernel.org/show_bug.cgi?id=15104
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jani-Matti Hätinen <jani-matti.hatinen@iki.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix assignment which overwrote SAT ATA PASS-THROUGH command EXTEND
bit setting (ATA_TFLAG_LBA48)
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
acpi_integer is now obsolete and removed from the ACPICA code base,
replaced by u64.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
libata currently doesn't retry if a command fails with AC_ERR_INVALID
assuming that retrying won't get it any further even if retried.
However, a failure may be classified as invalid through hardware
glitch (incorrect reading of the error register or firmware bug) and
there isn't whole lot to gain by not retrying as actually invalid
commands will be failed immediately. Also, commands serving FS IOs
are extremely unlikely to be invalid. Retry FS IOs even if it's
marked invalid.
Transient and incorrect invalid failure was seen while debugging
firmware related issue on Samsung n130 on bko#14314.
http://bugzilla.kernel.org/show_bug.cgi?id=14314
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Interestingly, when SIDPR is used in ata_piix, writes to DET in
SControl sometimes get ignored leading to detection failure. Update
sata_link_resume() such that it reads back SControl after clearing DET
and retry if it's not clear.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: fengxiangjun <fengxiangjun@neusoft.com>
Reported-by: Jim Faulkner <jfaulkne@ccs.neu.edu>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 871af1210f enabled 32bit PIO for
PATA piix but didn't for SATA. There's no reason not to use 32bit PIO
on SATA piix. Enable it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When sata_promise encounters an overrun or underrun error it
translates that to a libata AC_ERR_HSM, causing a hard reset.
Since over/under-runs were thought to be rare and transient,
this action seemed reasonable.
Unfortunately it turns out that the controller throws overrun
errors when e.g. hal polls a CD or DVD writer containing blank
media, causing long sequences of hard resets and retries before
EH finally gives up.
This patch updates sata_promise to classify over/under-runs as
AC_ERR_OTHER instead. This allows libata EH and upper layers to
retry or fail the operation as they see fit without the disruption
caused by repeated hard resets.
This fixes a problem using a DVD-RAM drive with sata_promise,
reported by Thomas Schorpp. I also tested it on a DVD-RW drive.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: thomas schorpp <thomas.schorpp@googlemail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In March 2008 commit 0ac4a3c2fb ("ACPI: fix
ATA_ACPI build") made CONFIG_ACPI_DOCK be selected by CONFIG_ATA_ACPI because
of a build error when CONFIG_ATA_ACPI=y and CONFIG_ACPI_DOCK=m.
However, in September 2008 commit 898b054f3e
("dock: make dock driver not a module") removed the possibility of having
CONFIG_ACPI_DOCK=m and therefore there is no need for selecting it when
CONFIG_ATA_ACPI=y.
This makes the kernel ~5 Kb smaller for people who don't have a dock by
allowing them to not have ACPI_DOCK compiled-in because of ATA_ACPI=y.
Signed-off-by: Carlos R. Mafra <crmafra@aei.mpg.de>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
By default, the PATA pins are routed to the async address lines in which
case, no peripheral muxing needs to be done. However, if the pins get
routed through the GPIO PORTs pins, we need to make sure to request them
so that the muxing is properly set up.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
adev->dma_mode stores the transfer mode value not UDMA mode number
so the condition in cmd64x_set_dmamode() is always true and the higher
UDMA clock is always selected. This can potentially result in data
corruption when UDMA33 device is used, when 40-wire cable is used or
when the error recovery code decides to lower the device speed down.
The issue was introduced in the commit 6a40da0 ("libata cmd64x: whack
into a shape that looks like the documentation") which goes back to
kernel 2.6.20.
Cc: stable@kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This reverts commit d43744390e, because
it breaks the boot on several machines (mostly sparc64, at present).
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: remove pointless NULL test
pata_hpt3x2n: fix clock turnaround
libata: fix reporting of drained bytes when clearing DRQ
sata_mv: add power management support for the PCI controllers.
sata_mv: store the board_idx into the host private data
pata_octeon_cf: use resource_size(), to fix resource sizing bug
libata: use the WRITE_SAME_16 define
sata_mv: move the PCI bar description initialization code
sata_mv: add power management support for the platform driver
sata_mv: support clkdev framework
sata_mv: increase PIO IORDY timeout
Fixed crazy mode-change in merge.
Remove !ap test, where ap is guaranteed not-NULL. Found by way of automated
bug report from Alexander Strakh via "Linux Device Drivers Verification
Project (Svace Detector)"
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The clock turnaround code still doesn't work for several reasons:
- 'USE_DPLL' flag in 'ap->host->private_data' is never initialized
or updated, so the driver can only set the chip to the DPLL clock
mode, not the PCI mode;
- the driver doesn't serialize access to the channels depending on
the current clock mode like the vendor drivers, so the clock
turnaround is only executed "optionally", not always as it should be;
- the wrong ports are written to when hpt3x2n_set_clock() is called
for the secondary channel;
- hpt3x2n_set_clock() can inadvertently enable the disabled channels
when resetting the channel state machines.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When we drain data from a device to clear DRQ during error recovery,
the number of bytes reported as drained is too low by a factor of 2
because the count is actually reporting the number of words drained,
not bytes. Fix this.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It appears the size for cs1 is calculated using the wrong resource.
Use the function resource_size to get the correct value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that the scsi tree has hit mainline we can use the newly added WRITE_SAME_16
define.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The mv_init_host will be used to initialize the host hw on resume.
The PCI bar description need to be initialized only once when the
device probed.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The old value (0xbc) in cycles of the IORDY timeout is suitable for
devices with core clock of 166 MHz, but some SoC controllers have
faster core clocks. The new value will make the IORDY timeout large
enough also for all SoC devices.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (151 commits)
powerpc: Fix usage of 64-bit instruction in 32-bit altivec code
MAINTAINERS: Add PowerPC patterns
powerpc/pseries: Track previous CPPR values to correctly EOI interrupts
powerpc/pseries: Correct pseries/dlpar.c build break without CONFIG_SMP
powerpc: Make "intspec" pointers in irq_host->xlate() const
powerpc/8xx: DTLB Miss cleanup
powerpc/8xx: Remove DIRTY pte handling in DTLB Error.
powerpc/8xx: Start using dcbX instructions in various copy routines
powerpc/8xx: Restore _PAGE_WRITETHRU
powerpc/8xx: Add missing Guarded setting in DTLB Error.
powerpc/8xx: Fixup DAR from buggy dcbX instructions.
powerpc/8xx: Tag DAR with 0x00f0 to catch buggy instructions.
powerpc/8xx: Update TLB asm so it behaves as linux mm expects.
powerpc/8xx: Invalidate non present TLBs
powerpc/pseries: Serialize cpu hotplug operations during deactivate Vs deallocate
pseries/pseries: Add code to online/offline CPUs of a DLPAR node
powerpc: stop_this_cpu: remove the cpu from the online map.
powerpc/pseries: Add kernel based CPU DLPAR handling
sysfs/cpu: Add probe/release files
powerpc/pseries: Kernel DLPAR Infrastructure
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
[SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
[SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
[SCSI] zfcp: Update FSF error reporting
[SCSI] zfcp: Improve ELS ADISC handling
[SCSI] zfcp: Simplify handling of ct and els requests
[SCSI] zfcp: Remove ZFCP_DID_MASK
[SCSI] zfcp: Move WKA port to zfcp FC code
[SCSI] zfcp: Use common code definitions for FC CT structs
[SCSI] zfcp: Use common code definitions for FC ELS structs
[SCSI] zfcp: Update FCP protocol related code
[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
[SCSI] zfcp: Assign scheduled work to driver queue
[SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
[SCSI] zfcp: Implement module unloading
[SCSI] zfcp: Merge trace code for fsf requests in one function
[SCSI] zfcp: Access ports and units with container_of in sysfs code
[SCSI] zfcp: Remove suspend callback
[SCSI] zfcp: Remove global config_mutex
[SCSI] zfcp: Replace local reference counting with common kref
...
This is a libata driver for the "macio" IDE controller used on most Apple
PowerMac and PowerBooks. It's a libata equivalent of drivers/ide/ppc/pmac.c
It supports all the features of its predecessor, including mediabay hotplug
and suspend/resume. It should also support module load/unload.
The timing calculations have been simplified to use pre-calculated tables
compared to drivers/ide/pmac.c and it uses the new mediabay interface
provided by a previous patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Tejun Heo <tj@kernel.org>
In libata-sff, ata_sff_post_internal_cmd() directly calls ata_bmdma_stop()
instead of ap->ops->bmdma_stop(). This can be a problem for controllers
that use their own bmdma_stop for which the generic sff one isn't suitable
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (54 commits)
Revert "pata_sis: Implement MWDMA for the UDMA 133 capable chips"
libata: Clarify ata_set_lba_range_entries function
libata: Report zeroed read after TRIM and max discard size
pata_hpt3x2n: fix overclocked MWDMA0 timing
pata_it8213: MWDMA0 is unsupported
[libata] MWDMA0 is unsupported on PIIX-like PATA controllers
pata_via: clear UDMA transfer mode bit for PIO and MWDMA
pata_sis: Power Management fix
pata_rz1000: Power Management fix
pata_radisys: fix UDMA handling
pata_ns87415: Power Management fix
pata_marvell: fix marvell_pre_reset() documentation
pata_legacy: add pointers to QDI65x0 documentation
pata_legacy: fix access to control register for QDI6580
pata_legacy: fix QDI6580DP support
pata_it8213: fix it8213_pre_reset() documentation
pata_it8213: fix wrong MWDMA timings being programmed
pata_it8213: fix PIO2 underclocking
pata_it8213: fix wrong PIO timings being programmed
pata_it8213: fix UDMA handling
...
This reverts commit f20941f334.
Sergei Shtylyov notes "You call min() on uncomparables [in
mwdma_clip_to_pio()], i.e. mwdma_to_pio[] contains XFER_PIO_* and
adev->pio_mode - XFER_PIO_0 yields you a mode number. Thus the second
argument will always "win" as a minimal one"
Bartlomiej Zolnierkiewicz adds "There are more issues with the patch related
to mwdma_clip_to_pio(). The function can return values between 0 and
4 which obviously won't work well for the new code below for values
>2 (i.e. resulting in out-of-bounds array access for the common-case
of dev->pio_mode == XFER_PIO_4)."
Bartlomiej Zolnierkiewicz also notes the patch is incomplete, failing to
update MWDMA mode masks.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ata_set_lba_range_entries used the variable max for two different things
which was confusing. Make the function take a buffer size in bytes as
argument and return the used buffer size upon completion.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Our current TRIM payload is a single sector that can accommodate 64 *
65535 blocks being unmapped. Report this value in the Block Limits
Maximum Unmap LBA count field.
If a storage device supports TRIM and the DRAT and RZAT bits are set,
report TPRZ=1 in Read Capacity(16).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove superfluous timings table entry while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MWDMA0 timings cannot be met with the PIIX based controller
programming interface.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Set correct bits to switch between UDMA2 and UDMA4.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix ->resume method to do chipset specific setup.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We need to mask out the port offset from the port number
cached in ld_qdi->timing.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dual port QDI6580 has shared PIO timings for master/slave
devices so it needs to use custom ->qc_issue method.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Clear old MWDMA timings before programming new ones (IT8213
is a single port host so there is no need to check ap->port_no).
This change should be safe as this is how we have been doing
things in IDE it8213 host driver for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
[ port of Sergei's fixes for pata_efar from commit 5f33b3b ]
Fix the PIO mode 2 using mode 0 timings -- this driver should enable the
fast timing bank starting with PIO2, just like the PIIX/ICH drivers do.
Also, fix/rephrase some comments while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* do not clear PIO timings for master when programming slave
* program new PIO timings in the correct register nibble
Both changes should be safe as this is how we have been doing
things in IDE it8213 host driver for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Driver should program the cycle timing not the mode number
(doing the latter results in wrong timings being used).
There shouldn't be any problems with it as IDE it8213 host driver
has been doing it this way for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It has been dead for the last three years (== since the initial driver
merge) and probability that it will ever get fixed is quite low.
Since there is no reason to keep this dead code around any longer just
remove it (it can still be retrieved from the git history if necessary).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Do not clear MWDMA timings for device on the other port when
programming slave device.
This change should be safe as this is how we have been doing
things in IDE slc90e66 host driver for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* do not clear PIO timings for master when programming slave
* do not clear PIO timings for device on the other port when
programming slave device
Both changes should be safe as this is how we have been doing
things in IDE slc90e66 host driver for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix erroneous check for ap->udma_mask in do_pata_set_dmamode()
resulting in controller not being programmed properly for MWDMA.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ahci can drive the Promise PDC42819, but obviously it can only use SATA
disks connected to this controller. The controller can actually support
SAS disks as well, but we only know how to use it in it's AHCI mode.
Add a message to let users know that because ahci is driving their chip
they can only use the SATA disks connected to this controller.
Signed-off-by: Mark Nelson <mdnelson8@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some places were using PCI_CLASS_REVISION instead of PCI_REVISION_ID, so
they weren't converted by commit 44c10138fd
(PCI: Change all drivers to use pci_device->revision).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The comment in the driver actually describes HPT37x's timing register layout,
which is different from HPT36x. Fix it and reformat the comment, while at it.
Bump the driver version, accounting for several patches that forgot to do it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
These drivers inherited from the older 'hpt366' IDE driver the buggy timing
register masks in their set_piomode() metods. As a result, too low command
cycle active time is programmed for slow PIO modes. Quite fortunately, it's
later "fixed up" by the set_dmamode() methods which also "helpfully" reprogram
the command timings, usually to PIO mode 4; unfortunately, setting an UltraDMA
mode #N also reprograms already set PIO data timings, usually to MWDMA mode #
max(N, 2) timings...
However, the drivers added some breakage of their own too: the bit that they
set/clear to control the FIFO is sometimes wrong -- it's actually the MSB of
the command cycle setup time; also, setting it in DMA mode is wrong as this
bit is only for PIO actually and clearing it for PIO modes is not needed as
no mode in any timing table has it set...
Fix all this, inverting the masks while at it, like in the 'hpt366' and
'pata_hpt366' drivers; bump the drivers' versions, accounting for recent
patches that forgot to do it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We were never able to get docs for this out of Toshiba for years. Dave
Barnes produced a NetBSD driver however and from that we can fill in the
needed tables.
As we correct the PCI identifiers a bit also update the old ide generic driver
at the same time so it stays compiling.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Making the new stuff work broke some of the old chipsets. We need to go
back to the old set up values for these it seems. Unfortunately even with
documentation this is basically a mix of cargoculting and guesswork.
Chased down to the exact line by Gianluca.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Daniela Engert pointed out that there are some implementation notes for the
643 and 646 that deal with certain serialization rules. In theory we don't
need them because they apply when the motherboard decides not to retry PCI
requests for long enough and the chip is busy doing a DMA transfer on the
other channel.
The rule basically is "don't touch the taskfile of the other channel while
a DMA is in progress". To implement that we need to
- not issue a command on a channel when there is a DMA command queued
- not issue a DMA command on a channel when there are PIO commands queued
- use the alternative access to the interrupt source so that we do not
touch altstatus or status on shared IRQ.
Updated to remote extra conditional check Bartlomiej noted and to remove
the variables for irq checks as the CMD648 doesn't have the underlying problem.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej pointed out that while this got fixed in the old driver whoever
did it didn't port it across.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reported by Mikulas Patocka.
VIA VT82C586B + Transcend TS64GSSD25-M v0826 does not work in UDMA mode
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In libata-sff, ata_sff_post_internal_cmd() directly calls ata_bmdma_stop()
instead of ap->ops->bmdma_stop(). This can be a problem for controllers
that use their own bmdma_stop for which the generic sff one isn't suitable
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for the ATA TRIM command in libata. We translate a WRITE SAME 16
command with the unmap bit set into an ATA TRIM command and export enough
information in READ CAPACITY 16 and the block limits EVPD page so that the new
SCSI layer discard support will driver this for us.
Note that I hardcode the WRITE_SAME_16 opcode for now as the patch to introduce
the symbolic is not in 2.6.32 yet but only in the SCSI tree - as soon as it is
merged we can fix it up to properly use the symbolic name.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
If ATA device failed FLUSH, it means that the device failed to write
out some amount of data and the error needs to be reported to upper
layers. As retries can't recover the lost data, FLUSH failures need to
be reported immediately in general.
However, if FLUSH fails due to transmission errors, the FLUSH needs to
be retried; otherwise, filesystems may switch to RO mode and/or raid
array may drop a drive for a random transmission glitch.
This condition can be rather easily reproduced on certain ahci
controllers which go through a PHY event after powersave mode switch +
ext4 combination. Powersave mode switch is often closely followed by
flush from the filesystem failing the FLUSH with ATA bus error which
makes the filesystem code believe that data is lost and drop to RO
mode. This was reported in the following bugzilla bug.
http://bugzilla.kernel.org/show_bug.cgi?id=14543
This patch makes libata EH retry FLUSH if it wasn't failed by the
device.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Andrey Vihrov <andrey.vihrov@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable device hot-plug support on Port multiplier fan-out ports
Signed-off-by: Ashish Kalra <Ashish.Kalra@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alan Cox reported that cable detection sometimes works unreliably
for HPT3xxN and that the issue is fixed by adding debounce delay
as used by the vendor driver.
Sergei Shtylyov also noticed that debounce delay is needed for all
HPT37x and HPT3xxN chipsets according to vendor drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The detection was reversed between primary and secondary ports.
Fix it to match hpt366 and the vendor driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sysfs attributes shouldn't require newlines. Make it possible to set the
link power management policy without a trailing newline.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We can use the same ->pre_reset method for all HPT37x chipsets now.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I obseved there is a sata_async_notification() for every ahci
interrupt. But the async notification does nothing (this is hard
disk drive and no pmp). This cause cpu wastes some time on sntf
register access.
It appears ICH AHCI doesn't support SNotification register, but the
controller reports it does. After quirking it, the async notification
disappears.
PS. it appears all ICH don't support SNotification register from ICH
manual, don't know if we need quirk all ICH. I don't have machines
with all kinds of ICH.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
