The old IDE cmd64x checks the status of the CNTRL register to see if
the ports are enabled before probing them. pata_cmd64x doesn't do
this, which causes a HPMC on parisc when it tries to poke at the
secondary port because apparently the BAR isn't wired up (and a
non-responding piece of memory causes a HPMC).
Fix this by porting the CNTRL register port detection logic from IDE
cmd64x. In addition, following converns from Alan Cox, add a check to
see if a mobility electronics bridge is the immediate parent and forgo
the check if it is (prevents problems on hotplug controllers).
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This reverts commit 270dac35c2.
The commits causes command timeouts on AC plug/unplug. It isn't yet
clear why. As the commit was for a single rather obscure controller,
revert the change for now.
The problem was reported and bisected by Gu Rui in bug#34692.
https://bugzilla.kernel.org/show_bug.cgi?id=34692
Also, reported by Rafael and Michael in the following thread.
http://thread.gmane.org/gmane.linux.kernel/1138771
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Gu Rui <chaos.proton@gmail.com>
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Michael Leun <lkml20100708@newton.leun.net>
Cc: Jian Peng <jipeng2005@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Saves about 50KB of data.
Old/new size of all objects:
text data bss dec hex filename
563015 80096 130684 773795 bcea3 (TOTALS)
610916 32256 130632 773804 bceac (TOTALS)
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be> (for drivers/net/can/softing/softing_cs.c)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
At the end of section 10.1 of AHCI spec (rev 1.3), it states
Software shall not set PxCMD.ST to 1 until it is determined that
a functoinal device is present on the port as determined by
PxTFD.STS.BSY=0, PxTFD.STS.DRQ=0 and PxSSTS.DET=3h
Even though most AHCI host controller works without this check,
specific controller will fail under this condition.
Signed-off-by: Jian Peng <jipeng2005@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The "struct ata_timing" must contain 10 members, but ".dmack_hold" member was
forgotten for "initial_timing" initialisation. This patch fixes such a problem.
Signed-off-by: Igor Plyatov <plyatov@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The AT91SAM9 microcontrollers with master clock higher then 105 MHz
and PIO0, have overflow of the NCS_RD_PULSE value in the MSB. This
lead to "NCS_RD_PULSE" pulse longer then "NRD_CYCLE" pulse and driver
does not detect ATA device.
Signed-off-by: Igor Plyatov <plyatov@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The previously submitted patch was word-wrapped.
This patch adds the AHCI-mode SATA DeviceIDs for the Intel Panther Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The previously submitted patch was word-wrapped.
This patch adds the IDE-mode SATA DeviceIDs for the Intel Panther
Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Commit 4a5610a04d fixed an issue with
the Pioneer DVR-212D not handling SETXFER correctly. An openSUSE user
reported a similar issue with his DVR-216D that the NOSETXFER horkage
worked around for him as well.
This patch adds the DVR-216D (1.08) to the horkage list for NOSETXFER.
The issue was reported at:
https://bugzilla.novell.com/show_bug.cgi?id=679143
Reported-by: Volodymyr Kyrychenko <vladimir.kirichenko@gmail.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The ahci_pmp_attach() & ahci_pmp_detach() unmask port irqs, but they
are also called during port initialization, before ahci host irq
handler is registered. On ce4100 platform, this sometimes triggers
"irq 4: nobody cared" message when loading driver.
Fixed this by not touching the register if the port is in frozen
state, and mark all uninitialized port as frozen.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
NVIDIA mcp65 familiy of controllers cause command timeouts when DIPM
is used. Implement ATA_FLAG_NO_DIPM and apply it.
This problem was reported by Stefan Bader in the following thread.
http://thread.gmane.org/gmane.linux.ide/48841
stable: applicable to 2.6.37 and 38.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stefan Bader <stefan.bader@canonical.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds an sysfs attribute 'em_message_supported' to the
ahci host device which prints out the supported enclosure management
message types.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use gpio_request_array() / gpio_free_array(), this makes the code
cleaner and less error prone.
This patch also properly frees GPIOs in case ata_host_activate() call fails.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
In FSL sata v2 block, the snoop bit of PRDT Word3 description
information is at bit28 instead of bit22.
This patch adds FSL sata v2 probe and resolve this difference.
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1b4b:91a3 seems to be another PCI ID for marvell ahci. Add it.
Reported and tested in the following thread.
http://thread.gmane.org/gmane.linux.kernel/1068354
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Borislav Petkov <bp@alien8.de>
Reported-by: Alessandro Tagliapietra <tagliapietra.alessandro@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
RX_WATER_MARK sets the number of locations in Rx FIFO that can be used before
the transport layer instructs the link layer to transmit HOLDS. Note that it
can take some time for the HOLDs to get to the other end, and that in the
interim there must be enough room in the FIFO to absorb all data that could
arrive.
Update the new recommended value to 16.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When a single device error is detected, the device under the error
is indicated by the error bit set in the DER. There is a one to one
mapping between register bit and devices on Port multiplier(PMP)
i.e. bit 0 represents PMP device 0 and bit 1 represents PMP device
1 etc.
Current implementation treats Device error register value as device
number not set of bits representing multiple device on PMP. It is
changed to consider bit level.
No need to check for each set bit as all command is going to be
aborted.
Signed-off-by: Ashish Kalra <B00888@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
As per SAT-3 the WWN ID should be included in the VPD page 0x83
(device identification) emulation.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some DMA controllers (eg: drivers/dma/dw_dmac*) allow platform specific
configuration for dma transfers. User drivers need to set chan->private field
of channel with pointer to configuration data. This patch takes dma_priv data
from platform data and passes it to chan->private_data, in order to pass
platform specific configuration to DMAC controller.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Commit 40d69ba029
("pata_hpt{37x|3x2n}: use pr_*(DRV_NAME ...) instead of printk(KERN_* ...)")
used pr_<level>.
Add #define pr_fmt and remove DRV_NAME.
Increment driver version numbers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The Arasan CompactFlash Device Controller has three basic modes of
operation: PC card ATA using I/O mode, PC card ATA using memory mode, PC card
ATA using true IDE modes.
Currently driver supports only True IDE mode.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds ata_sff_queue_work() & ata_sff_queue_delayed_work() routine in
libata-sff.c file. This routine can be used by ata drivers to use ata_sff_wq.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds an updated SATA RAID DeviceID for the Intel Patsburg PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Commit 6b7ae9545a (libata: reimplement link power
management) removed the check of ATA_FLAG_LPM but neglected to remove the flag
itself. Do it now...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
All checks of ATA_FLAG_NO_LEGACY have been removed by the commits
c791c30670 ([libata] minor PCI IDE probe
fixes and cleanups) and f0d36efdc6 (libata:
update libata core layer to use devres), so I think it's time to finally
get rid of this flag...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 0d5ff56677 (libata: convert to iomap)
removed all checks of ATA_FLAG_MMIO but neglected to remove the flag itself.
Do it now, at last...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
These flags are marked as obsolete and the checks for them have been removed
by commit 294440887b (libata-sff: kill unused
ata_bus_reset()), so I think it's time to finally get rid of them...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver makes use of the two options (CONFIG_SATA_DWC_[V]DEBUG) to enable
the debug output but they both are absent in drivers/ata/Kconfig...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver erroneously uses ata_get_cmd_descript() not only for printing out
the ATA commands but also the protocol and DMA direction enums. Add functions
for properly printing those out...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The caller expects this function to return the DMA channel number on success,
while it returns 0...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix the following compilation errors/warnings:
drivers/ata/sata_dwc_460ex.c:43:1: warning: "DRV_NAME" redefined
In file included from drivers/ata/sata_dwc_460ex.c:38:
drivers/ata/libata.h:31:1: warning: this is the location of the previous
definition
drivers/ata/sata_dwc_460ex.c:44:1: warning: "DRV_VERSION" redefined
drivers/ata/libata.h:32:1: warning: this is the location of the previous
definition
drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_exec_command_by_tag':
drivers/ata/sata_dwc_460ex.c:1356: warning: passing argument 1 of
`ata_get_cmd_descript' makes integer from pointer without a cast
drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_qc_issue':
drivers/ata/sata_dwc_460ex.c:1476: warning: `err' is used uninitialized in this
function
drivers/ata/sata_dwc_460ex.c:1465: note: `err' was declared here
drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_qc_issue':
drivers/ata/sata_dwc_460ex.c:1493: warning: passing argument 1 of
`ata_get_cmd_descript' makes integer from pointer without a cast
drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_qc_prep':
drivers/ata/sata_dwc_460ex.c:1537: error: `tag' undeclared (first use in this
function)
drivers/ata/sata_dwc_460ex.c:1537: error: (Each undeclared identifier is
reported only once
drivers/ata/sata_dwc_460ex.c:1537: error: for each function it appears in.)
NB: error only happens if DEBUG_NCQ macro is defined...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Somehow the driver was committed with a bare number for the PIO mask, instead
of ATA_PIO4...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Right at the moment, the libata error handler is incredibly
monolithic. This makes it impossible to use from composite drivers
like libsas and ipr which have to handle error themselves in the first
instance.
The essence of the change is to split the monolithic error handler
into two components: one which handles a queue of ata commands for
processing and the other which handles the back end of readying a
port. This allows the upper error handler fine grained control in
calling libsas functions (and making sure they only get called for ATA
commands whose lower errors have been fixed up).
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The SCSI host eh_cmd_q should be protected by the host lock (not the
port lock). This probably doesn't matter that much at the moment,
since we try to serialise the add and eh pieces, but it might matter
in future for more convenient error handling. Plus this switches
libata to the standard eh pattern where you lock, remove from the cmd
queue to a local list and unlock and then operate on the local list.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For historical reasons, libsas uses the scsi host lock as the ata port
lock, and libata always uses the ata host. For the old eh, this was
largely irrelevant since the two locks were never mixed inside the
code. However, the new eh has a case where it nests acquisition of
the host lock inside the port lock (this does look rather deadlock
prone). Obviously this would be an instant deadlock if the port lock
were the host lock, so switch the libsas paths to use the ata host
lock as well.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The function ata_sas_port_init() has always really done its own thing.
However, as a precursor to moving to the libata new eh, it has to be
properly using the standard libata scan paths. This means separating
the current libata scan paths into pieces which can be shared with
libsas and pieces which cant (really just the async call and the host
scan).
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_eh_analyze_serror() suppresses hotplug notifications if LPM is
being used because LPM generates spurious hotplug events. It compared
whether link->lpm_policy was different from ATA_LPM_MAX_POWER to
determine whether LPM is enabled; however, this is incorrect as for
drivers which don't implement LPM, lpm_policy is always
ATA_LPM_UNKNOWN. This disabled hotplug detection for all drivers
which don't implement LPM.
Fix it by comparing whether lpm_policy is greater than
ATA_LPM_MAX_POWER.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Final step to eliminate of_platform_bus_type. They're all just
platform drivers now.
v2: fix type in pasemi_nand.c (thanks to Stephen Rothwell)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
ata_pio_sectors() expects buffer for each sector to be contained in a
single page; otherwise, it ends up overrunning the first page. This
is achieved by setting queue DMA alignment. If sector_size is smaller
than PAGE_SIZE and all buffers are sector_size aligned, buffer for
each sector is always contained in a single page.
This wasn't applied to ATAPI devices but IDENTIFY_PACKET is executed
as ATA_PROT_PIO and thus uses ata_pio_sectors(). Newer versions of
udev issue IDENTIFY_PACKET with unaligned buffer triggering the
problem and causing oops.
This patch fixes the problem by setting sdev->sector_size to
ATA_SECT_SIZE on ATATPI devices and always setting DMA alignment to
sector_size. While at it, add a warning for the unlikely but still
possible scenario where sector_size is larger than PAGE_SIZE, in which
case the alignment wouldn't be enough.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: John Stanley <jpsinthemix@verizon.net>
Tested-by: John Stanley <jpsinthemix@verizon.net>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PIONEER DVR-212D can't do SETXFER like its sibling DVRTD08. Add
ATA_HORKAGE_NOSETXFER for it. Reported in bko#27502.
https://bugzilla.kernel.org/show_bug.cgi?id=27502
Signed-off-by: Francesco Antonacci <fraanto@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 5f173107ec added HFLAG_YES_FBS workaround for 88SE9128
(1b4b:9123).
However, that change inadvertently caused the legacy IDE interface of
the controller (with the same pci id) to become associated with the AHCI
driver as well, causing the driver to try to bring the interface up in
vain.
Fix that by matching against class as well.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit ab81a505ae (pata_hpt37x: unify ->pre_reset
methods) neglected to remove the initializer for the prereset() method from
'hpt374_fn1_port_ops' (it's inherited from 'hpt372_port_ops' anyway), as well
as to update the comment in hpt37x_init_one()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the AHCI-mode SATA DeviceID for the Intel DH89xxCC PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
hpt37x_init_one() has a large *if* statement which should really be folded into
the *switch* statement that currently constitutes its *else* branch, reducing
one level of indentation...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
... the same as the 'pata_hpt366' driver does.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
pata_mpc52xx supports BMDMA but inherits ata_sff_port_ops which
triggers BUG_ON() when a DMA command is issued. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Roman Fietze <roman.fietze@telemotive.de>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_HAVE_PATA_PLATFORM, by virtue of where its defined, has a
dependency on CONFG_ATA and CONFIG_ATA_SFF. This causes Kconfig
warnings when it is selected by various architectures, such as
warning: (ARCH_VEXPRESS && <choice> || ARCH_RPC && <choice> || MACH_VPAC270 && ARCH_PXA || MACH_REALVIEW_PB11MP && ARCH_REALVIEW || MACH_REALVIEW_PBA8 && ARCH_REALVIEW || MACH_REALVIEW_PBX && ARCH_REALVIEW || MACH_BAST_IDE && ARCH_S3C2410 || MACH_ANUBIS && ARCH_S3C2410) selects HAVE_PATA_PLATFORM which has unmet direct dependencies (ATA && ATA_SFF)
Since this option is only used to control visibility of the
CONFIG_PATA_PLATFORM option and isn't itself visible in the menu,
it is straightforward to simply remove these dependencies rather
than adjust all the architectures.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver clearly tries to limit HPT370[A] to UltraDMA/66 if the PCI clock is
less than 50 MHz but due to cut&paste type mistake this code has no effect...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix 8 errors and 3 warnings given by checkpatch.pl:
- *switch* and *case* not on the same indentation level;
- no space between *for*/*switch*/*while* and open parenthesis;
- space between an unary operator and its operand;
- spaces before tabs;
- lines over 80 characters.
In addition to these changes, also do the following:
- add new line after variable definitions;
- fix the style of some multi-line comments.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix 12 errors and 15 warnings given by checkpatch.pl:
- *switch* and *case* not on the same indentation level;
- no space between *for*/*switch*/*while* and open parenthesis;
- space between an unary operator and its operand;
- drive blacklist arrays not being *const*;
- spaces before tabs;
- lines over 80 characters.
In addition to these changes, also do the following:
- add new line after variable definitions;
- fix the style of some multi-line comments.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix 2 errors and 11 warnings given by checkpatch.pl:
- *switch* and *case* not on the same indentation level;
- no space between *switch* and open parenthesis;
- drive blacklist arrays not being *const*;
- spaces before tabs;
- lines over 80 characters.
In addition to these changes, also add new line after variable definition in
hpt36x_init_chipset()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Allow hpt3x2n_pci_clock() to calculate the average f_CNT register value iff
HighPoint BIOS hasn't saved one, just like the 'pata_hpt37x' driver (reading
the full 16-bit register, unlike what that driver does), so that this driver
would work correctly on e.g. non-x86 machine with 66 MHz PCI.
I'm not sure why Alan has only done this in one driver and not the other...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 28e21c8c0d (pata_hpt3x2n: Add HPT371N
support and other bits) forgot to update the driver's Kconfig entry, heading
comment, and module description (that also wrongly claims support of HPT302)
which may confuse users...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The Marvell bridge chips used on HighPoint SATA cards do not seem to support
the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes; these cards are
based on HPT372/372A/372N/374 chips (judging from the vendor drivers), so
the Linux drivers need to have a mode_filter() method for these chips...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
Add support for Acard ATP8620 host controller.
Based upon initial version by Jeff Garzik.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We don't need or want MSR usage here, on x86-64.
x86-64 was disabled intentionally in Kconfig, but commit
9272dcc232 changed that.
drivers/ata/pata_cs5536.c:47:1: warning: "rdmsr" redefined
In file included from arch/x86/include/asm/irqflags.h:60,
from include/linux/irqflags.h:15,
from arch/x86/include/asm/system.h:11,
from arch/x86/include/asm/processor.h:17,
from include/linux/prefetch.h:14,
from include/linux/list.h:7,
from include/linux/module.h:9,
from drivers/ata/pata_cs5536.c:33:
arch/x86/include/asm/paravirt.h:146:1: warning: this is the location of the previous definition
drivers/ata/pata_cs5536.c:48:1: warning: "wrmsr" redefined
arch/x86/include/asm/paravirt.h:154:1: warning: this is the location of the previous definition
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Low level drivers may behave differently depending on the current
link->lpm_policy. During ata_eh_set_lpm(), DIPM enable commands are
issued after the successful completion of ap->ops->set_lpm(), which
means that the controller is already in the target state. This causes
DIPM enable commands to be processed with mismatching controller power
state and link->lpm_policy value.
In ahci, link->lpm_policy is used to ignore certain PHY events if LPM
is enabled; however, as DIPM commands are issued with stale
link->lpm_policy, they sometimes end up triggering these conditions
and get aborted leading to LPM configuration failure.
Fix it by updating link->lpm_policy before issuing DIPM enable
commands.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_qc_complete() contains special handling for certain commands. For
example, it schedules EH for device revalidation after certain
configurations are changed. These shouldn't be applied to EH
commands but they were.
In most cases, it doesn't cause an actual problem because EH doesn't
issue any command which would trigger special handling; however, ACPI
can issue such commands via _GTF which can cause weird interactions.
Restructure ata_qc_complete() such that EH commands are always passed
on to __ata_qc_complete().
stable: Please apply to -stable only after 2.6.38 is released.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Found by this build-error if BMDMA is disabled:
drivers/ata/pata_mpc52xx.c: In function 'mpc52xx_ata_init_one':
drivers/ata/pata_mpc52xx.c:662: error: 'ata_bmdma_interrupt' undeclared (first use in this function)
...
Move the Kconfig entry to the proper location as needed since
9a7780c9ac (libata-sff: make BMDMA optional)
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
pata_cs5536 does work on the other platforms(e.g. Loongson, a MIPS
variant), so, remove the dependency of X86_32 and fix the building
errors under the other platforms via only reserving the X86_32 specific
parts for X86_32.
pata_amd also supports cs5536 IDE controller, but this one saves about
33k for the compressed kernel image(vmlinuz for MIPS).
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Signed-off-by: Chen Jie <chenj@lemote.com>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
While separating out BMDMA irq handler from SFF, commit c3b28894
(libata-sff: separate out BMDMA irq handler) incorrectly made
__ata_sff_port_intr() consider an IRQ to be an idle one if the host
state was transitioned to HSM_ST_ERR by ata_bmdma_port_intr().
This makes BMDMA drivers ignore IRQs reporting host bus error which
leads to timeouts instead of triggering EH immediately. Fix it by
making __ata_sff_port_intr() consider the IRQ to be an idle one iff
the state is HSM_ST_IDLE. This is equivalent to adding HSM_ST_ERR to
the "break"ing case but less error-prone.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Antonio Toma <antonio.toma@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
cancel_rearming_delayed_work[queue]() has been superceded by
cancel_delayed_work_sync() quite some time ago. Convert all the
in-kernel users. The conversions are completely equivalent and
trivial.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: netdev@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Alex Elder <aelder@sgi.com>
Cc: xfs-masters@oss.sgi.com
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netfilter-devel@vger.kernel.org
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: linux-nfs@vger.kernel.org
vt6420 has the same FIFO overflow problem as vt6421 when combined with
certain devices. This patch applies the magic fix to vt6420 too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Martin Qvist <q@maq.dk>
Reported-by: Peter Zijlstra <peterz@infradead.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
cmd->serial_number is never tested in any path we reach; therefore we may
remove the call to scsi_cmd_get_serial() inside DEF_SCSI_QCMD, the SCSI
host_lock acquisition surrounding it, and our own SCSI host_lock
unlock+relock cycle.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Delete successive assignments to the same location.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression i;
@@
*i = ...;
i = ...;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
pata_legacy is incorrectly testing PATA_WINBOND_VLB_MODULE instead of
CONFIG_PATA_WINBOND_VLB_MODULE. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: "Robert P. J. Day" <rpjday@crashcourse.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SCSI commands may be issued between __scsi_add_device() and dev->sdev
assignment, so it's unsafe for ata_qc_complete() to dereference
dev->sdev->locked without checking whether it's NULL or not. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The creation of the I/O clock domain requires some adjustments. Since the
CF bus timing logic is clocked by the I/O clock, use its rate for delay
calculations.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: linux-ide@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/1660/
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: remove in_workqueue_context()
workqueue: Clarify that schedule_on_each_cpu is synchronous
memory_hotplug: drop spurious calls to flush_scheduled_work()
shpchp: update workqueue usage
pciehp: update workqueue usage
isdn/eicon: don't call flush_scheduled_work() from diva_os_remove_soft_isr()
workqueue: add and use WQ_MEM_RECLAIM flag
workqueue: fix HIGHPRI handling in keep_working()
workqueue: add queue_work and activate_work trace points
workqueue: prepare for more tracepoints
workqueue: implement flush[_delayed]_work_sync()
workqueue: factor out start_flush_work()
workqueue: cleanup flush/cancel functions
workqueue: implement alloc_ordered_workqueue()
Fix up trivial conflict in fs/gfs2/main.c as per Tejun
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (26 commits)
include/linux/libata.h: fix typo
pata_bf54x: fix return type of bfin_set_devctl
Drivers: ata: Makefile: replace the use of <module>-objs with <module>-y
libahci: fix result_tf handling after an ATA PIO data-in command
pata_sl82c105: implement sff_irq_check() method
pata_sil680: implement sff_irq_check() method
pata_pdc202xx_old: implement sff_irq_check() method
pata_cmd640: implement sff_irq_check() method
ata_piix: Add device ID for ICH4-L
pata_sil680: make sil680_sff_exec_command() 'static'
ata: Intel IDE-R support
libata: reorder ata_queued_cmd to remove alignment padding on 64 bit builds
libata: Signal that our SATL supports WRITE SAME(16) with UNMAP
ata_piix: remove SIDPR locking
libata: implement cross-port EH exclusion
libata: add @ap to ata_wait_register() and introduce ata_msleep()
ata_piix: implement LPM support
libata: implement LPM support for port multipliers
libata: reimplement link power management
libata: implement sata_link_scr_lpm() and make ata_dev_set_feature() global
...
The new devctl func added for us to the driver has the wrong return
type. Which is to say there shouldn't be any. This fixes compile
time warnings as there shouldn't be any runtime difference.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ATA devices don't send D2H Reg FIS after an successful ATA PIO data-in
command. The host is supposed to take the TF and E_Status of the
preceding PIO Setup FIS. Update ahci_qc_fill_rtf() such that it takes
TF + E_Status from PIO Setup FIS after a successful ATA PIO data-in
command.
Without this patch, result_tf for such a command is filled with the
content of the previous D2H Reg FIS which belongs to a previous
command, which can make the command incorrectly seen as failed.
* Patch updated to grab the whole TF + E_Status from PIO Setup FIS
instead of just E_Status as suggested by Robert Hancock.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Mark Lord <kernel@teksavvy.com>
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ICH4-L is a variant of ICH4 lacking USB2 functionality and with some
different device IDs.
It is documented in Intel specification update 290745-025, currently
at <http://www.intel.com/assets/pdf/specupdate/290745.pdf>, and is
included in the device ID table for piix.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
... since, of course, it's not used outside this driver.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Intel IDE-R devices are part of the Intel AMT management setup. They don't
have any special configuration registers or settings so the ata_generic
driver will support them fully.
Rather than add a huge table of IDs for each chipset and keep sending in
new ones this patch autodetects them.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Until now identifying that a device supports WRITE SAME(16) with the
UNMAP bit set has been black magic. Implement support for the SBC-3
Thin Provisioning VPD page and set the TPWS bit.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that libata provides proper cross-port EH exclusion. The SIDPR
locking added by commit 213373cf (ata_piix: fix locking around SIDPR
access) is no longer necessary. Remove it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In libata, the non-EH code paths should always take and release
ap->lock explicitly when accessing hardware or shared data structures.
However, once EH is active, it's assumed that the port is owned by EH
and EH methods don't explicitly take ap->lock unless race from irq
handler or other code paths are expected. However, libata EH didn't
guarantee exclusion among EHs for ports of the same host. IOW,
multiple EHs may execute in parallel on multiple ports of the same
controller.
In many cases, especially in SATA, the ports are completely
independent of each other and this doesn't cause problems; however,
there are cases where different ports share the same resource, which
lead to obscure timing related bugs such as the one fixed by commit
213373cf (ata_piix: fix locking around SIDPR access).
This patch implements exclusion among EHs of the same host. When EH
begins, it acquires per-host EH ownership by calling ata_eh_acquire().
When EH finishes, the ownership is released by calling
ata_eh_release(). EH ownership is also released whenever the EH
thread goes to sleep from ata_msleep() or explicitly and reacquired
after waking up.
This ensures that while EH is actively accessing the hardware, it has
exclusive access to it while allowing EHs to interleave and progress
in parallel as they hit waiting stages, which dominate the time spent
in EH. This achieves cross-port EH exclusion without pervasive and
fragile changes while still allowing parallel EH for the most part.
This was first reported by yuanding02@gmail.com more than three years
ago in the following bugzilla. :-)
https://bugzilla.kernel.org/show_bug.cgi?id=8223
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Reported-by: yuanding02@gmail.com
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add optional @ap argument to ata_wait_register() and replace msleep()
calls with ata_msleep() which take optional @ap in addition to the
duration. These will be used to implement EH exclusion.
This patch doesn't cause any behavior difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that DIPM can be used independently from HIPM, ata_piix can
support LPM too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Port multipliers can do DIPM on fan-out links fine. Implement support
for it. Tested w/ SIMG 57xx and marvell PMPs. Both the host and
fan-out links enter power save modes nicely.
SIMG 37xx and 47xx report link offline on SStatus causing EH to detach
the devices. Blacklisted.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The current LPM implementation has the following issues.
* Operation order isn't well thought-out. e.g. HIPM should be
configured after IPM in SControl is properly configured. Not the
other way around.
* Suspend/resume paths call ata_lpm_enable/disable() which must only
be called from EH context directly. Also, ata_lpm_enable/disable()
were called whether LPM was in use or not.
* Implementation is per-port when it should be per-link. As a result,
it can't be used for controllers with slave links or PMP.
* LPM state isn't managed consistently. After a link reset for
whatever reason including suspend/resume the actual LPM state would
be reset leaving ap->lpm_policy inconsistent.
* Generic/driver-specific logic boundary isn't clear. Currently,
libahci has to mangle stuff which libata EH proper should be
handling. This makes the implementation unnecessarily complex and
fragile.
* Tied to ALPM. Doesn't consider DIPM only cases and doesn't check
whether the device allows HIPM.
* Error handling isn't implemented.
Given the extent of mismatch with the rest of libata, I don't think
trying to fix it piecewise makes much sense. This patch reimplements
LPM support.
* The new implementation is per-link. The target policy is still
port-wide (ap->target_lpm_policy) but all the mechanisms and states
are per-link and integrate well with the rest of link abstraction
and can work with slave and PMP links.
* Core EH has proper control of LPM state. LPM state is reconfigured
when and only when reconfiguration is necessary. It makes sure that
LPM state is reset when probing for new device on the link.
Controller agnostic logic is now implemented in libata EH proper and
driver implementation only has to deal with controller specifics.
* Proper error handling. LPM config failure is attributed to the
device on the link and LPM is disabled for the link if it fails
repeatedly.
* ops->enable/disable_pm() are replaced with single ops->set_lpm()
which takes @policy and @hints. This simplifies driver specific
implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Link power management is about to be reimplemented. Prepare for it.
* Implement sata_link_scr_lpm().
* Drop static from ata_dev_set_feature() and make it available to
other libata files.
* Trivial whitespace adjustments.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Link power management related symbols are in confusing state w/ mixed
usages of lpm, ipm and pm. This patch cleans up lpm related symbols
and sysfs show/store functions as follows.
* lpm states - NOT_AVAILABLE, MIN_POWER, MAX_PERFORMANCE and
MEDIUM_POWER are renamed to ATA_LPM_UNKNOWN and
ATA_LPM_{MIN|MAX|MED}_POWER.
* Pre/postfixes are unified to lpm.
* sysfs show/store functions for link_power_management_policy were
curiously named get/put and unnecessarily complex. Renamed to
show/store and simplified.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This build error showed up in linux-next tag next-20100820 for ia64:
WARNING: vmlinux.o(.init.text+0x4a952): Section mismatch in reference from the function ata_init() to the function .exit.text:ata_sff_exit()
The function __init ata_init() references
a function __exit ata_sff_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __exit annotation of
ata_sff_exit() so it may be used outside an exit section.
Sure enough, dropping the __exit fixes the problem.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This change enables my x86 machine to recognize and talk to a
"Native 4K" SATA device.
When I started working on this, I didn't know Matthew Wilcox had
posted a similar patch 2 years ago:
http://git.kernel.org/?p=linux/kernel/git/willy/ata.git;a=shortlog;h=refs/heads/ata-large-sectors
Gwendal Grignou pointed me at the the above code and small portions of
this patch include Matthew's work. That's why Mathew is first on the
"Signed-off-by:". I've NOT included his use of a bitmap to determine
512 vs Native for ATA command block size - just used a simple table.
And bugs are almost certainly mine.
Lastly, the patch has been tested with a native 4K 'Engineering
Sample' drive provided by Hitachi GST.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Grant Grundler <grundler@google.com>
Reviewed-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently, sata_fsl, mv and nv call ata_qc_complete() multiple times
from their interrupt handlers to indicate completion of NCQ commands.
This limits the visibility the libata core layer has into how commands
are being executed and completed, which is necessary to support IRQ
expecting in generic way. libata already has an interface to complete
multiple commands at once - ata_qc_complete_multiple() which ahci and
sata_sil24 already use.
This patch updates the three drivers to use ata_qc_complete_multiple()
too and updates comments on ata_qc_complete[_multiple]() regarding
their usages with NCQ completions. This change not only provides
better visibility into command execution to the core layer but also
simplifies low level drivers.
* sata_fsl: It already builds done_mask. Conversion is straight
forward.
* sata_mv: mv_process_crpb_response() no longer checks for illegal
completions, it just returns whether the tag is completed or not.
mv_process_crpb_entries() builds done_mask from it and passes it to
ata_qc_complete_multiple() which will check for illegal completions.
* sata_nv adma: Similar to sata_mv. nv_adma_check_cpb() now just
returns the tag status and nv_adma_interrupt() builds done_mask from
it and passes it to ata_qc_complete_multiple().
* sata_nv swncq: It already builds done_mask. Drop unnecessary
illegal transition checks and call ata_qc_complete_multiple().
In the long run, it might be a good idea to make ata_qc_complete()
whine if called when multiple NCQ commands are in flight.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Saeed Bishara <saeed@marvell.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a scheleton for libata transport class.
All information is read only, exporting information from libata:
- ata_port class: one per ATA port
- ata_link class: one per ATA port or 15 for SATA Port Multiplier
- ata_device class: up to 2 for PATA link, usually one for SATA.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add WQ_MEM_RECLAIM flag which currently maps to WQ_RESCUER, mark
WQ_RESCUER as internal and replace all external WQ_RESCUER usages to
WQ_MEM_RECLAIM.
This makes the API users express the intent of the workqueue instead
of indicating the internal mechanism used to guarantee forward
progress. This is also to make it cleaner to add more semantics to
WQ_MEM_RECLAIM. For example, if deemed necessary, memory reclaim
workqueues can be made highpri.
This patch doesn't introduce any functional change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
libata depends on scsi_host_template for module reference counting and
sht's should be owned by each low level driver. During libahci split,
the sht was left with libahci.ko leaving the actual low level drivers
not reference counted. This made ahci and ahci_platform always
unloadable even while they're being actively used.
Fix it by defining AHCI_SHT() macro in ahci.h and defining a sht for
each low level ahci driver.
stable: only applicable to 2.6.35.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Pedro Francisco <pedrogfrancisco@gmail.com>
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Keep track of the link on the which the current request is in progress.
It allows support of links behind port multiplier.
Not all libata-sff is PMP compliant. Code for native BMDMA controller
does not take in accound PMP.
Tested on Marvell 7042 and Sil7526.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For some mysterious reason, certain hardware reacts badly to usual EH
actions while the system is going for suspend. As the devices won't
be needed until the system is resumed, ask EH to skip usual autopsy
and recovery and proceed directly to suspend.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: Stephan Diestelhorst <stephan.diestelhorst@amd.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the Intel Patsburg (PCH) SATA AHCI and RAID Controller
DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the Intel Patsburg (PCH) IDE mode SATA Controller DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 978c0666 (libata: Remove excess delay in the tf_load path)
removed ata_wait_idle() from ata_sff_tf_load() and via_tf_load().
This caused obscure detection problems in sata_sil.
https://bugzilla.kernel.org/show_bug.cgi?id=16606
The commit was pure performance optimization. Revert it for now.
Reported-by: Dieter Plaetinck <dieter@plaetinck.be>
Reported-by: Jan Beulich <JBeulich@novell.com>
Bisected-by: gianluca <gianluca@sottospazio.it>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ahci_do_softreset() compared the current time and deadline in reverse
when calculating timeout for SRST issue. The result is that if
@deadline is in future, SRST is issued with 0 timeout, which hasn't
caused any problem because it later waits for DRDY with the correct
timeout. If deadline is already exceeded by the time SRST is about to
be issued, the timeout calculation underflows and if the device
doesn't respond, timeout doesn't trigger for a _very_ long time.
Reverse the incorrect comparison order.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Gwendal Grignou <gwendal@google.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
x % 1 always evaluates to 0, which clearly isn't the intent. The
author probably had "% 2" or "& 1" in mind, and mispelled it.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove harmful BUG_ON() from ata_bmdma_qc_issue(),
as it casts too wide of a net and breaks sata_mv.
It also crashes the kernel while doing the BUG_ON().
There's already a WARN_ON_ONCE() further down to catch
the case of POLLING for a BMDMA operation.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
Fix DSM/TRIM commands in sata_mv (v2).
These need to be issued using old-school "BM DMA",
rather than via the EDMA host queue.
Since the chips don't have proper BM DMA status,
we need to be more careful with setting the ATA_DMA_INTR bit,
since DSM/TRIM often has a long delay between "DMA complete"
and "command complete".
GEN_I chips don't have BM DMA, so no TRIM for them.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
ata_qc_issue() BUG_ON()s on data commands w/o data, which may be
submitted via SG_IO. Be less of a drama queen and just trigger
WARN_ON_ONCE() and fail the command with AC_ERR_SYSTEM.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stefan Hübner <stefan.huebner@stud.tu-ilmenau.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dma_dwc_xfer_setup() returns an int and "dma_chan" needs to be signed
for the error handling to work.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
88SE9128 can do FBS and sets it in HOST_CAP but forgets to set FBSCP
in PORT_CMD. Implement AHCI_HFLAG_YES_FBS and apply it to 88SE9128.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Winbond W83759A controller is fully supported by pata_legacy driver
so remove no longer needed pata_winbond driver.
Leave PATA_WINBOND_VLB config option for compatibility reasons
and teach pata_legacy to preserve the old behavior of pata_winbond
driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit d62f5576 (pata_cmd64x: fix handling of address setup timings)
incorrectly called ata_timing_compute() on UDMA mode on 0 @UT leading
to devide by zero fault. Revert it until better fix is available.
This is reported in bko#16607 by Milan Kocian who also root caused it.
https://bugzilla.kernel.org/show_bug.cgi?id=16607
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-root-caused-by: Milan Kocian <milan.kocian@wq.cz>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some minor improvements in error handling, but overall it was mostly dead
code.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (226 commits)
ARM: 6323/1: cam60: don't use __init for cam60_spi_{flash_platform_data,partitions}
ARM: 6324/1: cam60: move cam60_spi_devices to .init.data
ARM: 6322/1: imx/pca100: Fix name of spi platform data
ARM: 6321/1: fix syntax error in main Kconfig file
ARM: 6297/1: move U300 timer to dynamic clock lookup
ARM: 6296/1: clock U300 intcon and timer properly
ARM: 6295/1: fix U300 apb_pclk split
ARM: 6306/1: fix inverted MMC card detect in U300
ARM: 6299/1: errata: TLBIASIDIS and TLBIMVAIS operations can broadcast a faulty ASID
ARM: 6294/1: etm: do a dummy read from OSSRR during initialization
ARM: 6292/1: coresight: add ETM management registers
ARM: 6288/1: ftrace: document mcount formats
ARM: 6287/1: ftrace: clean up mcount assembly indentation
ARM: 6286/1: fix Thumb-2 decompressor broken by "Auto calculate ZRELADDR"
ARM: 6281/1: video/imxfb.c: allow usage without BACKLIGHT_CLASS_DEVICE
ARM: 6280/1: imx: Fix build failure when including <mach/gpio.h> without <linux/spinlock.h>
ARM: S5PV210: Fix on missing s3c-sdhci card detection method for hsmmc3
ARM: S5P: Fix on missing S5P_DEV_FIMC in plat-s5p/Kconfig
ARM: S5PV210: Override FIMC driver name on Aquila board
ARM: S5PC100: enable FIMC on SMDKC100
...
Fix up conflicts in arch/arm/mach-{s5pc100,s5pv210}/cpu.c due to
different subsystem 'setname' calls, and trivial port types in
include/linux/serial_core.h
'make htmldocs' has a fatal error when processing libata.xml, as seen
below. The string "Example patterns:" (or any string with "example.*:"
in it AFAIK) causes some part of the doc generation tool chain to try to
produce an <informalexample> block without a beginning <para>, but
there is an ending </para> generated, which throws things out of kilter.
I don't even know where (what program) this is happening in.
I searched in docproc and xmlto and in some XML stylesheets without
finding anything. If anyone can give me pointers about this, please do.
Until this is fixed, let's just spell "Example" as "Sample"
and match up the double quotation marks while there.
Documentation/DocBook/libata.xml:6575: parser error : Opening and ending tag mismatch: programlisting line 6573 and para
</para><para>
^
Documentation/DocBook/libata.xml:6580: parser error : Opening and ending tag mismatch: para line 6575 and programlisting
</programlisting></informalexample>
^
unable to parse Documentation/DocBook/libata.xml
make[2]: *** [Documentation/DocBook/libata.html] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (55 commits)
workqueue: mark init_workqueues() as early_initcall()
workqueue: explain for_each_*cwq_cpu() iterators
fscache: fix build on !CONFIG_SYSCTL
slow-work: kill it
gfs2: use workqueue instead of slow-work
drm: use workqueue instead of slow-work
cifs: use workqueue instead of slow-work
fscache: drop references to slow-work
fscache: convert operation to use workqueue instead of slow-work
fscache: convert object to use workqueue instead of slow-work
workqueue: fix how cpu number is stored in work->data
workqueue: fix mayday_mask handling on UP
workqueue: fix build problem on !CONFIG_SMP
workqueue: fix locking in retry path of maybe_create_worker()
async: use workqueue for worker pool
workqueue: remove WQ_SINGLE_CPU and use WQ_UNBOUND instead
workqueue: implement unbound workqueue
workqueue: prepare for WQ_UNBOUND implementation
libata: take advantage of cmwq and remove concurrency limitations
workqueue: fix worker management invocation without pending works
...
Fixed up conflicts in fs/cifs/* as per Tejun. Other trivial conflicts in
include/linux/workqueue.h, kernel/trace/Kconfig and kernel/workqueue.c
Remove the current bio flags and reuse the request flags for the bio, too.
This allows to more easily trace the type of I/O from the filesystem
down to the block driver. There were two flags in the bio that were
missing in the requests: BIO_RW_UNPLUG and BIO_RW_AHEAD. Also I've
renamed two request flags that had a superflous RW in them.
Note that the flags are in bio.h despite having the REQ_ name - as
blkdev.h includes bio.h that is the only way to go for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Remove all the trivial wrappers for the cmd_type and cmd_flags fields in
struct requests. This allows much easier grepping for different request
types instead of unwinding through macros.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: avoid buffer overflow in pcmcia_setup_isa_irq
pcmcia: do not request windows if you don't need to
pcmcia: insert PCMCIA device resources into resource tree
pcmcia: export resource information to sysfs
pcmcia: use struct resource for PCMCIA devices, part 2
pcmcia: remove memreq_t
pcmcia: move local definitions out of include/pcmcia/cs.h
pcmcia: do not use io_req_t when calling pcmcia_request_io()
pcmcia: do not use io_req_t after call to pcmcia_request_io()
pcmcia: use struct resource for PCMCIA devices
pcmcia: clean up cs.h
pcmcia: use pcmica_{read,write}_config_byte
pcmcia: remove cs_types.h
pcmcia: remove unused flag, simplify headers
pcmcia: remove obsolete CS_EVENT_ definitions
pcmcia: split up central event handler
pcmcia: simplify event callback
pcmcia: remove obsolete ioctl
Conflicts in:
- drivers/staging/comedi/drivers/*
- drivers/staging/wlags49_h2/wl_cs.c
due to dev_info_t and whitespace changes
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
Make the following changes to prepare for NCQ command completion
update. Changes made by this patch don't cause any functional
difference.
* sata_fsl_host_intr(): rename the local variable qc_active to
done_mask as that's what it is.
* mv_process_crpb_response(): restructure if clause for easier update.
* nv_adma_interrupt(): drop unnecessary error variable.
* nv_swncq_sdbfis(): drop unnecessary nr_done and return 0 on success.
Typo fix.
* nv_swncq_dmafis(): drop unused return value and return void.
* nv_swncq_host_interrupt(): drop unnecessary return value handling.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Saeed Bishara <saeed@marvell.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SIDPR window registers are shared across ports and as each access is
done in two steps, accesses to different ports under EH may race.
This primarily is caused by incorrect host locking in EH context and
should be fixed by defining locking requirements for each EH operation
which can be used during EH and enforcing them but for now work around
the problem by adding a dedicated SIDPR lock and grabbing it for each
SIDPR access.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Mark Knecht <markknecht@gmail.com>
Reported-by: Paul Check <paul@thechecks.ca>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Take further advantage of the new glob_match() function to reduce
the blacklist size, this time making use of "character ranges" in
the patterns.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable use of hyphenated pattern ranges in glob_match(), similar to how
shell globbing works, and how developers might expect things to work.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 1529c69adc (ata_generic: implement ATA_GEN_* flags and force
enable DMA on MBP 7,1) implemented ATA_GEN_FORCE_DMA for forcing DMA
mode and applied it to CENATEK but forgot to remove the original hard
coded logic. This is removal of redundant logic and doesn't affect
correctness.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The below patch casts ATA_MAX_QUEUE to int because GCC will
give a warning message about the two different enum blocks:
CC drivers/ata/ahci.o
drivers/ata/ahci.c: In function 'ahci_init_one':
drivers/ata/ahci.c:1045:2: warning: comparison between 'enum <anonymous>' and 'enum <anonymous>'
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Adds support for the Samsung PATA controller. This driver is based
on the Libata subsystem and references the earlier patches sent for
IDE subsystem.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch enables the on-chip DWC SATA controller of the AppliedMicro
processor 460EX.
Signed-off-by: Rupjyoti Sarmah <rsarmah@appliedmicro.com>
Signed-off-by: Mark Miesfeld <mmiesfeld@appliedmicro.com>
Signed-off-by: Prodyut Hazarika <phazarika@appliedmicro.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Take further advantage of the new glob_match() function to reduce
the blacklist size. There are even more savings possible, but how
far do we want to go with this?
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Take advantage of the new glob_match() function to reduce the blacklist
size somewhat. There are further savings possible, but these are
the most obvious biggies.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Replace rudimentry pattern matching with more capable shell-style globbing.
This will enable shrinking ata_device_blacklist[] table in subsequent patches,
and helps with future editions to the table, such as matching only the end
of a firmware revision string etc..
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver is using platform_driver_probe() during initialization,
so ahci_driver.probe hook is never used.
But it causes the following (harmless, luckily) section mismatch:
WARNING: vmlinux.o(.data+0x2fb20): Section mismatch in reference
from the variable ahci_driver to the function .init.text:ahci_probe()
This patch removes the ahci_driver.probe assignment, thus fixes
the warning.
p.s. Note that there's another patch[1] from Rene Bolldorf that
tried to solve the same issue by __refdata annotation. __refdata
says that this reference is actually OK, but in fact it is not OK,
because dereferencing .probe() will cause problems. So the proper
fix is to remove the assignment.
[1] http://kerneltrap.org/mailarchive/linux-kernel/2010/3/18/4549547
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some AHCI implementations may use Vendor Specific HBA[A0h, FFh]
and/or Port[70h, 7Fh] registers to 'prepare' for initialization.
For that, the platform needs memory mapped address of AHCI registers.
This patch adds the 'mmio' argument and reorders the call to
platform init function.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata has two concurrency related limitations.
a. ata_wq which is used for polling PIO has single thread per CPU. If
there are multiple devices doing polling PIO on the same CPU, they
can't be executed simultaneously.
b. ata_aux_wq which is used for SCSI probing has single thread. In
cases where SCSI probing is stalled for extended period of time
which is possible for ATAPI devices, this will stall all probing.
#a is solved by increasing maximum concurrency of ata_wq. Please note
that polling PIO might be used under allocation path and thus needs to
be served by a separate wq with a rescuer.
#b is solved by using the default wq instead and achieving exclusion
via per-port mutex.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
IDE mode of MCP89 on MBP 7,1 doesn't set DMA enable bits in the BMDMA
status register. Make the following changes to work around the problem.
* Instead of using hard coded 1 in id->driver_data as class code
match, use ATA_GEN_CLASS_MATCH and carry the matched id in
host->private_data.
* Instead of matching PCI_VENDOR_ID_CENATEK, use ATA_GEN_FORCE_DMA
flag in id instead.
* Add ATA_GEN_FORCE_DMA to the id entry of MBP 7,1.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Cc: stable@kernel.org
Reported-by: Anders Østhus <grapz666@gmail.com>
Reported-by: Andreas Graf <andreas_graf@csgraf.de>
Reported-by: Benoit Gschwind <gschwind@gnu-log.net>
Reported-by: Damien Cassou <damien.cassou@gmail.com>
Reported-by: tixetsal@juno.com
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For yet unknown reason, MCP89 on MBP 7,1 doesn't work w/ ahci under
linux but the controller doesn't require explicit mode setting and
works fine with ata_generic. Make ahci ignore the controller on MBP
7,1 and let ata_generic take it for now.
Reported in bko#15923.
https://bugzilla.kernel.org/show_bug.cgi?id=15923
NVIDIA is investigating why ahci mode doesn't work.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Cc: stable@kernel.org
Reported-by: Anders Østhus <grapz666@gmail.com>
Reported-by: Andreas Graf <andreas_graf@csgraf.de>
Reported-by: Benoit Gschwind <gschwind@gnu-log.net>
Reported-by: Damien Cassou <damien.cassou@gmail.com>
Reported-by: tixetsal@juno.com
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In function ahci_store_em_buffer(), if the input (signed char*) buffer
contains negative data, the constructed 32-bit long message data may
be wrong.
Signed-off-by: Harry Zhang <harry.zhang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds a driver for a harddrive attached to PXA address and data bus.
Unlike pata_platform, this driver allows usage of PXA DMA controller, making the
transmission speed 3x higher.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The data in the cmd_block buffers may reach the main memory after the
writel() to the device ports. This patch introduces two calls to wmb()
to ensure the relative ordering.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Colin Tuckley <colin.tuckley@arm.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
cb->atapi.cdb is an array of 16 u8 elements. The call too memset()
would set the first part of the sge array to zero as well. It's not
a packed struct.
This one has been around for five years. I found it with Smatch. I
think the reason no one has seen it before is because we normally call
sil24_fill_sg() and that overwrites sge with proper information?
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 96d60303fd (ahci: Turn off DMA engines when there's no device)
implemented stopping DMA engines on empty ports but it used single
sampling of status registers to determine device presence which led to
disabling of DMA engines on occupied ports. Do it after all EH
actions are complete using device presence state determined by EH.
This avoids spurious disabling of DMA engines and simplifies the code.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: Marc Dionne <marc.c.dionne@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The sata_sil24 driver has six 16-bit registers that are initialised with
32-bit writes. This cause a kernel panic on ARM due to the unaligned
accesses which result.
This patch changes the accesses to the correct 16-bit ones.
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add Joseph Chan's explanation of the problem and workaround to the
VT6421 magic fix.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: implement on-demand HPA unlocking
libata: use the enlarged capacity after late HPA unlock
SCSI: implement sd_unlock_native_capacity()
libata-sff: trivial corrections to Kconfig help text
sata_nv: don't diddle with nIEN on mcp55
sata_via: magic vt6421 fix for transmission problems w/ WD drives
Implement ata_scsi_unlock_native_capacity() which will be called
through SCSI layer when block layer notices that partitions on a
device extend beyond the end of the device. It requests EH to unlock
HPA, waits for completion and returns the current device capacity.
This allows libata to unlock HPA on demand instead of having to decide
whether to unlock upfront. Unlocking on demand is safer than
unlocking by upfront because some BIOSes write private data to the
area beyond HPA limit. This was suggested by Ben Hutchings.
Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
After late HPA unlock, libata kept using the original capacity
ignoring the new larger native capacity. Enlarging device on the fly
doesn't cause any harm. Use the larger native capacity instead. This
will enable on-demand HPA unlocking.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On mcp55, nIEN gets stuck once set and liteon blueray rom iHOS104-08
violates ATA specification and fails to set I on D2H Reg FIS if nIEN
is set when the command was issued. When the other party is following
the spec, both devices can work fine but when the two flaws are put
together, they can't talk to each other.
mcp55 has its own IRQ masking mechanism and there's no reason to mess
with nIEN in the first place. Fix it by dropping nIEN diddling from
nv_mcp55_freeze/thaw().
This was originally reported by Cengiz. Although Cengiz hasn't
verified the fix yet, I could reproduce this problem and verfiy the
fix. Even if Cengiz is experiencing different or additional problems,
this patch is needed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Cengiz Günay <cgunay@emory.edu>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
vt6421 has problems talking to recent WD drives. It causes a lot of
transmission errors while high bandwidth transfer as reported in the
following bugzilla entry.
https://bugzilla.kernel.org/show_bug.cgi?id=15173
Joseph Chan provided the following fix. I don't have any idea what it
does but I can verify the issue is gone with the patch applied.
Signed-off-by: Tejun Heo <tj@kernel.org>
Originally-from: Joseph Chan <JosephChan@via.com.tw>
Reported-by: Jorrit Tijben <sjorrit@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Grant patches added an of mach table to struct device_driver. However,
while he changed the macio device code to use that, he left the match
table pointer in struct macio_driver and didn't update drivers to use
the "new" one, thus breaking the probing.
This completes the change by moving all drivers to setup the "new"
one, removing all traces of the old one, and while at it (since it
changes the exact same locations), I also remove two other duplicates
from struct driver which are the name and owner fields.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add dump_id libata.force parameter. If specified, libata dumps full
IDENTIFY data during device configuration. This is to aid debugging.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Larry Baker <baker@usgs.gov>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There are ATAPI devices which raise AN when hit by commands issued by
open(). This leads to infinite loop of AN -> MEDIA_CHANGE uevent ->
udev open() to check media -> AN.
Both ACS and SerialATA standards don't define in which case ATAPI
devices are supposed to raise or not raise AN. They both list media
insertion event as a possible use case for ATAPI ANs but there is no
clear description of what constitutes such events. As such, it seems
a bit too naive to export ANs directly to userland as MEDIA_CHANGE
events without further verification (which should behave similarly to
windows as it apparently is the only thing that some hardware vendors
are testing against).
This patch adds libata.atapi_an module parameter and disables ATAPI AN
by default for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Nick Bowler <nbowler@elliptictech.com>
Cc: David Zeuthen <david@fubar.dk>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make BMDMA optional depending on new config variable CONFIG_ATA_BMDMA.
In Kconfig, drivers are grouped into five groups - non-SFF native, SFF
w/ custom DMA interface, SFF w/ BMDMA, PIO-only SFF, and generic
fallback / legacy ones. Kconfig and Makefile are reorganized
according to the groups and ordered alphabetically inside each group.
ata_ioports.bmdma_addr and ata_port.bmdma_prd[_dma] are put into
CONFIG_ATA_BMDMA, as are all bmdma related ops, variables and
functions.
This increase the binary size slightly when BMDMA is enabled but on
both native-only and PIO-only configurations the size is slightly
reduced. Either way, the size difference is insignificant. This
change is more meaningful to signify the separation between SFF and
BMDMA and as a tool to verify the separation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that SFF and BMDMA are completely separate, sata_qstor and
pata_octeon_cf which inherit from ata_sff_port_ops don't need to worry
about BMDMA ops being called. Kill the dummy BMDMA ops.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Separate out ata_pci_bmdma_prepare_host() and ata_pci_bmdma_init_one()
from their SFF counterparts. SFF ones no longer try to initialize
BMDMA or set PCI master.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Separate out BMDMA irq handler from SFF irq handler. The misnamed
host_intr() functions are renamed to ata_sff_port_intr() and
ata_bmdma_port_intr(). Common parts are factored into
__ata_sff_port_intr() and __ata_sff_interrupt() and used by sff and
bmdma interrupt routines.
All BMDMA drivers now use ata_bmdma_interrupt() or
ata_bmdma_port_intr() while all non-BMDMA SFF ones use
ata_sff_interrupt() or ata_sff_port_intr().
For now, ata_pci_sff_init_one() uses ata_bmdma_interrupt() as it's
used by both SFF and BMDMA drivers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_sff_irq_clear() is BMDMA specific. Rename it to
ata_bmdma_irq_clear(), move it to ata_bmdma_port_ops and make
->sff_irq_clear() optional.
Note: ata_bmdma_irq_clear() is actually only needed by ata_piix and
possibly by sata_sil. This should be moved to respective low
level drivers later.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that BMDMA EH ops are separated out from SFF ops, mv5_ops doesn't
have to explicitly reset ->error_handler() and ->post_internal_cmd().
Drop them.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
