Replace kfree_skb with dev_consume_skb_any in free_tx_desc that can be
called in hard irq and other contexts. dev_consume_skb_any is used
as this function consumes successfully transmitted skbs.
Replace dev_kfree_skb with dev_kfree_skb_any in t4_eth_xmit that can
be called in hard irq and other contexts, on paths that drop the skb.
Replace dev_kfree_skb with dev_consume_skb_any in t4_eth_xmit that can
be called in hard irq and other contexts, on paths that successfully
transmit the skb.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace kfree_skb with dev_consume_skb_any in free_tx_desc, and
write_tx_pkt_wr that can be called in hard irq and other contexts.
Replace dev_kfree_skb with dev_kfree_skb_any in t3_eth_xmit that can
be called in hard irq and other contexts.
dev_kfree_skb is replaced with dev_kfree_skb_any in t3_eth_xmit as
that location is a packet drop, while kfree_skb in free_tx_desc,
and in write_tx_pkt_wr are places where packets are consumed
in a healthy manner.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace dev_kfree_skb with dev_consume_skb_any in xgmac_tx_complete
that can be called in hard irq and other contexts.
Replace dev_kfree_skb with dev_kfree_skb_any in xgmac_xmit that can
be called in hard irq and other contexts.
dev_consume_skb_any is used in xgamc_tx_complete as skbs that reach
there have been successfully transmitted, dev_kfree_skby_any is used
in xgmac_xmit as skbs that are freed there are being dropped.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace kfree_skb with dev_kfree_skb_any in macb_start_xmit that can
be called in hard irq and other contexts.
macb_start_xmit only frees skbs when dropping them so
dev_kfree_skb_any is used.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace dev_kfree_skb with dev_kfree_skb_any in bnad_start_xmit that
can be called in hard irq and other contexts.
dev_kfree_skb_any is used as bnad_start_xmit only frees skbs when to
drop them, normally transmitted packets are handled elsewhere.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The call path: atl1c_xmit_frame, atlc_tx_rollback, atl1c_clean_buffer
can not be tell at compile time if it will be invoked from hard irq
or other context, as atl1c_xmit_frame does not know. So remove
the logic that passes the compile time knowledge into al1c_clean_buffer
and figure out it out at runtime with dev_consume_skb_any.
Replace dev_kfree_skb with dev_kfree_skb_any in atl1c_xmit_frame that
can be called in hard irq and other contexts.
Replace dev_kfree_skb and dev_kfree_skb_irq with dev_consume_skb_any
in atl1c_clean_buffer that can be called in hard irq and other
contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace dev_kfree_skb with dev_kfree_skb_any in alx_start_xmit that
can be called in hard irq and other contexts.
dev_kfree_skb_any is used as alx_start_xmit only frees skbs
when dropping them.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace dev_kfree_skb with dev_kfree_skb_any in pcnet32_start_xmit
that can be called in hard irq and other contexts.
dev_kfree_skb_any is used as pcnet32_start_xmit only frees an
skb when it drops a packet during transmit.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace dev_kfree_skb with dev_consume_skb_any in lance_start_xmit
that can be called in hard irq and other contexts.
dev_consume_skb_any is used as lance_start_xmit always immediately
consumes the skb.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace dev_kfree_skb with dev_consume_skb_any in am79c961 that can
be called in hard irq and other contexts.
dev_consume_skb_any is used as am79c961_sendpacket always
immediately consumes the skb.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace dev_kfree_skb with dev_consume_skb_any in emacs_start_xmit
which can be called in hard irq and other contexts.
emac_start_xmit always transmits the packet making dev_consume_skb
the appropriate function to call.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace dev_kfree_skb with dev_consume_skb_any in _tx_reclaim_skb that
can be called in hard irq and other contexts.
dev_consume_skb is used as _tx_reclaim_skb is called after a packet
has been successfully transmitted.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace dev_kfree_skb with dev_consume_skb_any in __ei_start_xmit that
can be called in hard irq and other contexts.
dev_consume_skb is used as in this simple driver the skb is always
immediately consumed, there are no drops.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace dev_kfree_skb with dev_consume_skb_any in vortex_start_xmit
as it can be called in hard irq and other contexts.
dev_consume_skb_any is used when vortext_start_xmit directly consumes
the packet instead of dmaing it to the device.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace dev_kfree_skb with dev_consume_skb_any in el3_start_xmit
as it can be called in hard irq and other contexts.
dev_consume_skb_any is used as on this simple hardware the
skb is consumed directly by the start_xmit function.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to igb, ixgbe, ixgbevf, i40e and i40evf.
Anjali provides a i40e/i40evf patch to add Energy Efficient Ethernet
Low Power Idle stats and a fix for i40e to change the string
"Side Band" to "Sideband" for consistency.
Mitch provides 2 patches for i40evf to fix if the driver encounters
an error while communicating with the PF driver, do not shut down the
admin queue unconditionally. Add an error message when the admin
queue message never completes and fix formatting on another message
that was unnecessarily wrapped.
Mark provides a ixgbe patch and five ixgbevf patches. Fix a possible
infinite recursion when an adapter is removed and registers all read
as all one's in ixgbe_clear_vmdq_generic() and ixgbe_clear_rar_generic().
Converts macros to static inline functions to align kernel coding standard
and prepare for adding Live Error Recovery (LER) to ixgbevf. Change the
ethtool register test to use the normal register accessor functions and
eliminate macors used for calling register test functions to make error
exits more clear. Checks all register reads for adapter removal by checking
the status register after any register read that returns all F's since the
status register will never return 0xFFFFFFFF unless the adapter is removed.
Jacob implements SIOCGHWTSTAMP ioctl for igb which enables user processes
to read the current hardware stamp config settings non-destructively.
Todd adds the initial register read and write for surprise removal (LER)
for igb.
Christian Engelmayer fixes an igb memory leak in the igb_get_module_eeprom()
error handling path.
Ken Ichikawa provides a fix for igb, specifically for 82575 hardware to
specify -1 to the phc_index for ethtool's get_ts_info, otherwise a wrong
value will be set to the phc_index.
Christopher Paasch fixes a null pointer dereference in igb and makes sure
to unset the HAS_MSIX flag when the driver falls back to MSI only.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As commit a6e28b34205b("staging/et131x: use SET_ETHTOOL_OPS
directly"), using a wrapper around SET_ETHTOOL_OPS macro is
not actually required, remove and use SET_ETHTOOL_OPS directly.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses two typos in the original driver submission. One derived
from a cut & paste error, and another is a misspelling.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses a portable pointer arithmetic issue in the
original submission found by the kbuild test robot.
config: make ARCH=i386 allyesconfig
altera_sgdma.c: In function 'sgdma_txphysaddr':
>> altera_sgdma.c:393:33: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
dma_addr_t offs = (dma_addr_t)((dma_addr_t)desc -
^
>> altera_sgdma.c:394:5: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
(dma_addr_t)priv->tx_dma_desc);
^
altera_sgdma.c: In function 'sgdma_rxphysaddr':
>> altera_sgdma.c:403:33: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
dma_addr_t offs = (dma_addr_t)((dma_addr_t)desc -
^
>> altera_sgdma.c:404:5: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
(dma_addr_t)priv->rx_dma_desc);
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the version number returned by the driver's get regs routine
invoked by ethtool so formatting can be dependent on the version
number returned, and any interesting formatted output can check
the version number for specific types of register data returned.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds Rx checksum offload support for VXLAN.
Implements .ndo_{add|del}_vxlan_port netdev ops.
Adapter supports only one VXLAN port, so program adapter with
very first UDP port which VXLAN driver is listening to.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds LSO, LSO6 and Tx checksum offload support for VXLAN
encapsulated packets on 83xx/84xx series adapters.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The P1010 device tree restricts the number of
supported interrupt groups to 1, although the eth
controller can support 2 interrupt groups and the
driver assumes the Multi-Group mode ("fsl,etsec2" model).
So, in this case the assumption that the Multi-Group
mode (MQ_MG_MODE) devices always support 2 interrupt
groups is false. To fix this, a check for the actual
number of interrupt groups enabled in the board's
device tree has been added in gfar_probe for the
"fsl,etsec2" devices.
Without this fix, P1010 based boards claim support for
2 Tx queues to the net stack but only one is actually
allocated, leading to NULL access in xmit. This issue
was introduced by enabling Single-Queue polling for
the P1010 devices.
(71ff9e3 gianfar: Use Single-Queue polling for
"fsl,etsec2")
Fixes: 71ff9e3df7
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the many PTP Hardware Clock drivers with the
newly introduced field that advertises the number of programmable
pins. Some of these devices do have programmable pins, but the
implementation will have to wait for follow on patches.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When igb_set_interrupt_capability() calls
igb_reset_interrupt_capability() (e.g., because CONFIG_PCI_MSI is unset),
num_q_vectors has been set but no vector has yet been allocated.
igb_reset_interrupt_capability() will then call igb_reset_q_vector,
which assumes that the vector is allocated. As this is not the case, we
are accessing a NULL-pointer.
This patch fixes it by checking that q_vector is indeed different from
NULL.
Fixes: 02ef6e1d0b (igb: Fix queue allocation method to accommodate changing during runtime)
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
82575 has only software timestamping capability and it has
no PTP Hardware Clocks. Therefore, -1 has to be specified
to the phc_index for ethtool's get_ts_info, otherwise a wrong
value will be set to the phc_index.
v2: move the if (adapter->ptp_clock) section specifying phc_index
to above the switch statement as suggested by Matthew Vick.
adapter->ptpclock will always be NULL for 82575.
Signed-off-by: Ken ICHIKAWA <ichikawa.ken@jp.fujitsu.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a memory leak in the igb_get_module_eeprom() error handling path.
Detected by Coverity: CID 1016508.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for the SIOCGHWTSTAMP ioctl which enables user
processes to read the current hwtstamp_config settings
non-destructively. Previously a process had to be privileged and could
only set values, it couldn't return what is currently set without
possibly overwriting the value.
This patch adds support for this new operation into igb by keeping a
shadow copy of the config in the adapter structure, which is returned
upon request.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Additional checks are needed for a detected removal not to cause
problems. Some involve simply avoiding a lot of stuff that can't
do anything good, and also cases where the phony return value can
cause problems. In addition, down the adapter when the removal is
sensed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Prevent writes to an adapter that has been detected as removed
by a previous failing read.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check all register reads for adapter removal by checking the status
register after any register read that returns 0xFFFFFFFF. Since the
status register will never return 0xFFFFFFFF unless the adapter is
removed, such a value from a status register read confirms the
removal. Since this patch adds so much to ixgbe_read_reg, stop
inlining it, to reduce driver bloat.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make the ethtool register test use the normal register accessor
functions. Also eliminate macros used for calling register test
functions to make error exits clearer.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kernel coding standard prefers static inline functions instead
of macros, so use them for register accessors. This is to prepare
for adding LER, Live Error Recovery, checks to those accessors.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When an adapter is removed and registers all read as all one's,
an infinite recursion can happen between ixgbe_clear_vmdq_generic
and ixgbe_clear_rar_generic. Adding a check for removal breaks
this recursion.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an error message when the admin queue message never completes, and
fix formatting on another one that was unnecessarily wrapped.
Change-ID: I8b8a4eb7629d741f09357250144023cd4a72231f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the driver encounters an error while communicating with the PF
driver, don't just shut down the admin queue unconditionally. The PF
may be delayed, and shutting down the admin queue causes it to fail
completely. If this happens, the VF will never complete initialization.
Change-ID: I6192e9d8caeefb738428c3597fa2f54fa400ce7f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of always invoking netdev_get_tx_queue() in bcmgenet_xmit() and
bcmgenet_tx_reclaim(), just get the corresponding netdev_queue pointer
once and for all and manipulate it throughout bcmgenet_xmit() and
bcmgenet_tx_reclaim().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_pick_tx already takes care of making sure that a given
skb->queue_mapping value will remain within the number of advertised
hardware queue number, there is no need to re-do this again in the
driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCMGENET driver was not TX timestamping the SKBs it queued for
transmission, do this in bcmgenet_xmit() right before kicking the
Transmit DMA engine.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock cookie in bcmgenet_priv is never used, get rid of it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"goto" is well accepted for error paths in the kernel but should not be
used unnecessarily. Return the correct value directly instead of using a
goto when possible.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network API functions that rely on the MDIO bus can be called as soon as
the driver calls register_netdev(). Register the MDIO bus before the
network device to avoid race conditions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device passed to the sh_mdio_init and sh_mdio_release
functions is only used to access the sh_eth_private instance. Pass it
directly to those functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO bus parent is set to the network device. Beside not reflecting
the hardware topology, this prevents registering the MDIO bus before
initializing the network device. Fix it by setting the MDIO bus parent
to the platform device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory allocated for the MDIO bus with the devm_kzalloc() API is
associated with the network device. While this will cause memory to be
freed at the right time, it doesn't allow allocating memory before the
network device is initialized.
Replace the network device with the parent platform device for memory
allocation to remove that dependency. This also improves consistency
with the other devm_* calls in the driver that all use the platform
device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
