The sunxi reset controller code is only used with sun6i (a31).
After the platform has been split up into per-soc options, it's
now possible to build it without the reset controller code, so
the base platform init must not call into the reset driver
if that is turned off at compile time.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The versatile express changes for 3.16 introduced a number of
build regressions for randconfig kernels by not tracking dependencies
between the components right.
This patch tries to rectify that:
* the mach-vexpress code cannot link without the syscfg driver,
which in turn needs MFD_VEXPRESS_SYSREG
* various drivers call devm_regmap_init_vexpress_config(), which
has to be exported so it can be used by loadable modules
* the configuration bus uses OF DT helper functions that are not
available to platforms disable CONFIG_OF
* The sysreg driver exports GPIOs through gpiolib, which can
be disabled on some platforms.
* The clocksource code cannot be built on platforms that don't
use modern timekeeping but rely on gettimeoffset.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With the newly introduced CPU_METHOD_OF_DECLARE is not necessary anymore
to reference the relevant smp_ops in the board file, but instead it can
simply be set by the enable-method property of the cpu nodes.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
According to the ARM ARM, the behaviour is UNPREDICTABLE if the PC read
from the exception return stack is not half word aligned. See the
pseudo code for ExceptionReturn() and PopStack().
The signal handler's address has the bit 0 set, and setup_return()
directly writes this to regs->ARM_pc. Current hardware happens to
discard this bit, but QEMU's emulation doesn't and this makes processes
crash. Mask out bit 0 before the exception return in order to get
predictable behaviour.
Fixes: 19c4d593f0 ("ARM: ARMv7-M: Add support for exception handling")
Cc: stable@kernel.org
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The arm EABI states that unwind opcode 10100nnn means pop register r4-4[4+nnn],aditionally there is a similar unwind opcode: 10101nnn which means the same thing plus popping r14. Those two cases are handled by the unwind_exec_pop_r4_to_rN function which checks whether the 4th bit is set and does r14 popping.
However, up until now it has been checking whether the 8th bit was set (mask & 0x80) instead of the 4th (mask & 0x8), a simple to make typo but this meant that we were always popping r14 even if we had the former opcode.
This patch changes the mask so that the 2 unwind opcodes are being handled correctly.
Signed-off-by: Nikolay Borisov <Nikolay.Borisov@arm.com>
Reviewed-by: Anurag Aggarwal <anurag19aggarwal@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to arm procedure call standart r2 register is call-cloberred.
So after the result of x expression was put into r2 any following
function call in p may overwrite r2. To fix this, the result of p
expression must be saved to the temporary variable before the
assigment x expression to __r2.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
__v7m_setup_stack currently sits in the .proc.info.init section, and
thus creates a bogus proc info entry (which by the way matches any
unknown CPU IDs, due to the entry's mask being 0). Move it out of
there.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A look at the code reveals use of S5P_VA_SYSRAM macro, in case of certain SoC
revisions, which is not valid any longer, after SYSRAM started to be mapped
dynamically. The new dynamic mapping is stored in sysram_base_addr variable,
which is declared static in platsmp.c
This fix makes sysram_base_addr non-static, declared it in common.h and used
in pm.c instead of S5P_VA_SYSRAM.
Suggested-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
No more dependency on the arch code. The platform_data field is used to set the
PM callback as the other cpuidle drivers.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This macro is only used there.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The code to initiate and exit the powerdown sequence is the same in
pm.c and cpuidle.c.
Let's split the common part in the pm.c and reuse it from the cpu_pm notifier.
That is one more step forward to make the cpuidle driver arch indenpendant.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In order to remove depedency on pm code, let's move the 'exynos_enter_aftr'
function into the pm.c file as well as the other helper functions.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Let's encapsulate the AFTR state specific call into a single function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
There is no point to register the cpuidle driver for the 5440 as it has only
one WFI state which is the default idle function when the cpuidle driver is
disabled.
By disabling cpuidle we prevent to enter to the governor computation for
nothing, thus saving a lot of processing time.
The only drawback is the statistic via sysfs on this state which is lost but
it is meaningless and it could be retrieved from the ftrace easily.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pass the wakeup mask to 'exynos_set_wakeupmask' as this function could
be used for different idle states with different mask.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The scu_enable function is already a noop in the scu's header file is
CONFIG_SMP=n, so no need to use these macros in the code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
We make the cpuidle code less arch dependent.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use the cpu_pm_enter/exit notifier to group some pm code inside the
pm file.
The save and restore code is duplicated across pm.c and cpuidle.c. By
using the cpu_pm notifier, we can factor out the routine.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This function should be called only when the powerdown sequence fails.
Even if the current code does not hurt, by moving this line, we have
the same code than the one in pm.c.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Move the code around to differentiate different section of code and
prepare it to be factored out in the next patches.
The call order changed but hat doesn't have a side effect because
they are independent. The important call is cpu_do_idle() which must
be done the last.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
That makes the code cleaner and encapsulted. The function will be
reused in the next patch.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The driver was initially written for exynos4 but the driver is used
also for exynos5.
Change the function prefix name exynos4 -> exynos
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use the cpuidle generic function 'cpuidle_register'. That saves us
from some extra lines of code and unneeded variables.
A side effect of this change is a bug fix where before the cpuidle
driver was registered for each_online_cpu and now it is for
each_possible_cpu.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Move the structure below the 'exynos4_enter_lowpower' function so no
more need of forward declaration.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now with common clock support added for exynos5250 it is necessary to
move this code to exynos5250 common clock driver as clock registers
should be handled there. This change is tested in exynos5250 based
arndale platform.
Cc: Abhilash Kesavan <a.kesavan@samsung.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsugn.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
[t.figa: Rebased onto current kernel sources.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Move debug-macro.S from mach/include to include/debug where
all other common debug macros are.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This removes the need for mach/-headers in the debug macro.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Using the lowlevel debug uart is a corner case - even more so in a
multiplatform environment. So it seems reasonable to simply let the
developer set the appropriate uart type for the debugged SoC.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
addruart from the generic debug macro is doing exactly the same using
the common lowlevel uart definition, so there is no cause for this
special casing for s3c24xx.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos specific macros and declarations have been moved to
mach-exynos. Inclusion of plat/cpu.h is no more necessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Move Exynos specific macros to mach-exynos from plat-samsung to avoid
unnecessary dependency on plat based header files.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
'exynos_subsys' has no users. Remove this code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Group all files compiled under common config option together.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
A common macro v7_exit_coherency_flush available which does the below
tasks in the seqeunce.
-clearing C bit
-clearing L1 cache
-exit SMP
-instruction and data synchronization
So removing the local functions which does the same thing and use the
macro instead.
Signed-off-by: Leela Krishna Amudala <leela.krishna@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
[cw00.choi@samsung.com: tested on exynos3250 based board]
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* only show ARCH_BCM in multi v6/v7 configs
* enable ARM erratum 775420
* bcm_defconfig updates for pwm
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qAvl
-----END PGP SIGNATURE-----
Merge tag 'for-3.16/bcm-soc' of git://github.com/broadcom/mach-bcm into next/soc
Merge "mach-bcm 3.16 soc updates" From Matt Porter:
* only show ARCH_BCM in multi v6/v7 configs
* enable ARM erratum 775420
* bcm_defconfig updates for pwm
* tag 'for-3.16/bcm-soc' of git://github.com/broadcom/mach-bcm:
ARM: bcm_defconfig: Enable PWM and Backlight
ARM: mach-bcm: add ARM_ERRATA_775420
ARM: bcm: Restrict ARCH_BCM selection to ARCH_MULTI_V6_V7
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Clean up bcm281xx/21664 SMC code
* Clean up bcm281xx/21664 L2C code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QVlm
-----END PGP SIGNATURE-----
Merge tag 'for-3.16/bcm-cleanup' of git://github.com/broadcom/mach-bcm into next/cleanup
* Clean up mach-bcm config and build targets
* Clean up bcm281xx/21664 SMC code
* Clean up bcm281xx/21664 L2C code
* tag 'for-3.16/bcm-cleanup' of git://github.com/broadcom/mach-bcm:
ARM: bcm: rename "kona.h" and "kona.c"
ARM: bcm: rewrite commentary for bcm_kona_do_smc()
ARM: bcm: use inline assembly for "smc" request
ARM: bcm: tidy up a few includes
ARM: bcm: config option for l2 cache support
ARM: bcm: don't special-case CPU 0 in bcm_kona_smc()
ARM: bcm: have bcm_kona_smc() return request result
ARM: bcm: clean up SMC code
ARM: bcm: err, don't BUG() on SMC init failures
ARM: bcm: use memory accessors for ioremapped area
ARM: bcm: clean up config and build targets
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-bcm/Kconfig
Toradex Colibri Evaluation Board uses the DS1307 RTC and the
MCP251x CAN controller. The NVIDIA Tegra 3 based Colibri T30
module can be used on this carrier board, hence enable those
drivers in tegra_defonfig and multi_v7_defconfig.
Furthermore the NVIDIA Tegra 3 based Apalis T30 module too
contains two MCP251x CAN controller.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Marvell Armada 38x platform has a SDHCI interface managed by the
sdhci-pxav3 MMC host driver. It therefore makes sense to enable this
driver in multi_v7_defconfig, which supports the Armada 38x platform.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Marvell Armada 38x platform needs the xhci_mvebu driver enabled
for the xHCI USB hosts, so this commit enables the corresponding
Kconfig option in multi_v7_defconfig.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: arm@kernel.org
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Add a new qcom_defconfig for mach-qcom
* Update msm_defconfig for handling building the old mach-msm
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
Comment: GPGTools - https://gpgtools.org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=RyxN
-----END PGP SIGNATURE-----
Merge tag 'qcom-defconfig-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into next/defconfig
Merge "Qualcomm ARM Based defconfig Updates for v3.16" from Kumar Gala:
* Add a new qcom_defconfig for mach-qcom
* Update msm_defconfig for handling building the old mach-msm
* tag 'qcom-defconfig-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: config: Update msm_defconfig
ARM: config: Add qcom_defconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the A31 reset driver to the sunxi-related defconfigs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1akP
-----END PGP SIGNATURE-----
Merge tag 'sunxi-defconfig-for-3.16-2' of https://github.com/mripard/linux into next/defconfig
Merge "Allwinner defconfig changes, take 2" from Maxime Ripard:
Add the A31 reset driver to the sunxi-related defconfigs
* tag 'sunxi-defconfig-for-3.16-2' of https://github.com/mripard/linux:
ARM: multi_v7: Add Allwinner reset drivers to multi_v7_defconfig
ARM: sunxi: Add A31 reset driver to sunxi_defconfig
ARM: sunxi: drop CONFIG_COMMON_CLK_DEBUG
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- mvebu
- enable MSI and XHCI in mvebu_v7_defconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ZWKb
-----END PGP SIGNATURE-----
Merge tag 'mvebu-defconfig-3.16-2' of git://git.infradead.org/linux-mvebu into next/defconfig
Merge "mvebu defconfig changes for v3.16 (incremental #2)" from Jason Cooper:
- mvebu
- enable MSI and XHCI in mvebu_v7_defconfig
* tag 'mvebu-defconfig-3.16-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: enable MSI support in mvebu_v7_defconfig
ARM: configs: enable XHCI mvebu support in mvebu_v7_defconfig
ARM: multi_v5_defconfig: Enable sound modules needed for t5325
ARM: mvebu_v5_defconfig: Enable sound modules needed for t5325
ARM: mvebu: defconfig: add MTD_SPI_NOR (new dependency for M25P80)
ARM: configs: add ahci_mvebu to mvebu_v7_defconfig
ARM: configs: add CONFIG_MMC_SDHCI_PXAV3 to the mvebu_v7_defconfig
ARM: mvebu: enable fhandle in the defconfigs
ARM: mvebu: Enable nfsroot in the defconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "mvebu DT changes for v3.16 (incremental #2)" from Jason Cooper:
- kirkwood
- add OpenRD boards
- make keymile boards bootable with latest kernels
- mvebu
- add ehci/xhci to Armada 375/38x boards
* tag 'mvebu-dt-3.16-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: kirkwood: add kirkwood-km_fixedeth DTS file
ARM: dts: kirkwood: add kirkwood-km_common DTSI files
ARM: dts: kirkwood: resynch 98dx4122 dtsi
ARM: mvebu: add Device Tree description for the EHCI controllers on Armada 375
ARM: mvebu: add Device Tree description of the xHCI controller on Armada 375
ARM: mvebu: add Device Tree description of the EHCI controller on Armada 38x
ARM: mvebu: add Device Tree description of xHCI controllers on Armada 38x
ARM: Kirkwood: DT versions of OpenRD boards
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "Allwinner DT changes for 3.16, take 2" from Maxime Ripard:
- Introduction of a new board, the i12-tvbox
- Enable the MMC and USB controllers on the Colombus
- Add the enable-method to the A31 cpus
- a few fixes
* tag 'sunxi-dt-for-3.16-2' of https://github.com/mripard/linux:
ARM: dts: sun7i: Add new i12-tvbox board
ARM: dts: sun7i: cubietruck: set mmc3 bus-width property
ARM: sun6i: Add MMC0 controller to the Colombus board
ARM: sun6i: Fix OHCI2 node name
ARM: sun6i: Enable USB Host support on the Colombus board
ARM: sunxi: Add fixed 3V regulator
ARM: sun6i: Define the A31 CPUs enable-method
ARM: sunxi: dt: build DTs according to new MACH_SUNxI Kconfig symbols
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/boot/dts/Makefile
Merge "mach-bcm dt updates for 3.16" from Matt Porter:
* Add PWM support to bcm281xx and bcm28155 ap board
* Add gpldo and vbus regulators to bcm590xx
* tag 'for-3.16/bcm-dt' of git://github.com/broadcom/mach-bcm:
ARM: dts: bcm590xx: add support for GPLDO and VBUS regulators
ARM: dts: Enable the PWM for bcm28155 AP board
ARM: dts: Declare the PWM for bcm11351 (bcm281xx)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "Qualcomm ARM Based Device Tree Updates for v3.16" from Kumar Gala:
* Added device tree nodes for pinctrl and SDHC for msm8974 SoC/DB8074 board
* Added binding spec for GSBI configuration node
* tag 'qcom-dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
soc: qcom: Add device tree binding for GSBI
ARM: dts: msm: Add SDHC controller nodes for MSM8974 and DB8074 board
ARM: dts: MSM8974: Add pinctrl node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "ARM: STi: DT changes for v3.16, v3" from Maxime Coquelin:
Please consider these STi DT updates for v3.16.
This 3rd version takes into account Olof's comments on the v2:
- Fix upper-cases in labels and node names
- Sort compatibles order from specific to generic
- Sort dts entries in Makefile
It also adds support for the B2020 revision E board for STiH416 SoC.
Note that two reset patches are part of this pull request, in order to avoid
compilation breakage.
Adding these two patches in this pull request has been accepted by Philipp Zabel.
* tag 'sti-dt-for-v3.16-1' of git://git.stlinux.com/devel/kernel/linux-sti: (23 commits)
ARM: sti: stih41x: Provide a proper header for this DTSI file
ARM: sti: stih416: Enable board LED support for B2020 RevE
ARM: sti: stih416: Add support for B2020 RevE
ARM: STi: DT: STiH41x Add clk_ignore_unused to bootargs
ARM: STi: DT: STiH415: 415 DT Entry for clockgen A9
ARM: STi: DT: STiH415: Remove unused CLK_S_GMAC0_PHY & CLK_S_ETH1_PHY fixed clocks
ARM: STi: DT: STiH415: Remove unused CLK_S_ICN_REG_0 fixed clock
ARM: STi: DT: STiH415: 415 DT Entry for clockgen A0/1/10/11/12
ARM: STi: DT: STiH416: 416 DT Entry for clockgen A9/DDR/GPU
ARM: STi: DT: STiH416: 416 DT Entry for clockgen B/C/D/E/F
ARM: STi: DT: STiH416: Remove unused CLK_S_GMAC0_PHY & CLK_S_ETH1_PHY fixed clocks
ARM: STi: DT: STiH416: Remove unused CLK_S_ICN_REG_0 fixed clock
ARM: STi: DT: STiH416: 416 DT Entry for clockgen A0/1/10/11/12
ARM: STi: DT: STiH41x: Rename CLK_SYSIN into clk_sysin
ARM: STi: DT: add keyscan for stih41x-b2000
ARM: STi: DT: add keyscan for stih416
ARM: STi: DT: add keyscan for stih415
driver: reset: sti: add keyscan for stih416
driver: reset: sti: add keyscan for stih415
ARM: dts: STiH407: Add B2120 board support
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "Allwinner Core additions for 3.16, take 2" from Maxime Ripard:
- Convert the A31 SMP operations to the CPU_METHOD_OF_DECLARE mechanism
- Remove the reset code from the machine definition, that removes pretty much
all the code left in mach-sunxi
* tag 'sunxi-core-for-3.16-2' of https://github.com/mripard/linux:
ARM: sunxi: Remove init_machine callback
ARM: sunxi: Remove reset code from the platform
ARM: sun6i: Retire the smp field in A31 machine
Documentation: dt: bindings: Document Allwinner A31 enable method
ARM: sun6i: Use CPU_METHOD_OF_DECLARE
Documentation: dt: bindings: Document ARM PSCI enable method
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "Qualcomm ARM Based SoC Updates for v3.16" from Kumar Gala:
* Enabling building pinctrl and AMBA bus support
* Clean up debug UART selection
* tag 'qcom-soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: qcom: Select PINCTRL by default for ARCH_QCOM
ARM: debug: qcom: make UART address selection configuration option
ARM: qcom: Enable ARM_AMBA option for Qualcomm SOCs.
Conflicts:
arch/arm/Kconfig.debug
arch/arm/mach-qcom/Kconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "mvebu SoC changes for v3.16 (incremental #2)" from Jason Cooper <jason@lakedaemon.net>:
- mvebu
- fix coherency on big-endian in -next
- hardware IO coherency
- L2/PCIe deadlock workaround
- small coherency cleanups
* tag 'mvebu-soc-3.16-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: returns ll_get_cpuid() to ll_get_coherency_cpumask()
ARM: mvebu: improve comments in coherency_ll.S
ARM: mvebu: fix indentation of assembly instructions in coherency_ll.S
ARM: mvebu: fix big endian booting after coherency code rework
ARM: mvebu: coherency: fix registration of PCI bus notifier when !PCI
ARM: mvebu: implement L2/PCIe deadlock workaround
ARM: mvebu: use hardware I/O coherency also for PCI devices
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Patches from Anders Berg applied individually:
Here is version 4 of platform support for AXM5516 SoC.
The clk driver is now applied to clk-next. The rest should be ready for
arm-soc. Haven't got any response from the power/reset maintainers... I hope
this driver can be taken via arm-soc as well.
The AXM55xx family consists of devices that may contain up to 16 ARM Cortex-A15
cores (in a 4x4 cluster configuration). The cores within each cluster share an
L2 cache, and the clusters are connected to each other via a CCN-504 cache
coherent interconnect.
This machine requires CONFIG_ARM_LPAE enabled as all peripherals are located
above 4GB in the memory map.
* axxia/soc:
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
ARM: dts: Device tree for AXM55xx.
ARM: Add platform support for LSI AXM55xx SoC
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The setup_max_cpus variable is only defined if CONFIG_SMP is set. Add
a preprocessor condition to avoid the following compilation error if
CONFIG_SMP is not set:
arch/arm/include/asm/trusted_foundations.h: In function 'register_trusted_foundations':
arch/arm/include/asm/trusted_foundations.h:57:2: error: 'setup_max_cpus' undeclared (first use in this function)
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a defconfig file for the LSI Axxia family of devices (CONFIG_ARCH_AXXIA).
Signed-off-by: Anders Berg <anders.berg@lsi.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add device tree for the Amarillo validation board with an AXM5516 SoC.
Signed-off-by: Anders Berg <anders.berg@lsi.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The AXM55xx family consists of devices that may contain up to 16 ARM Cortex-A15
cores (in a 4x4 cluster configuration). The cores within each cluster share an
L2 cache, and the clusters are connected to each other via a CCN-504 cache
coherent interconnect.
This machine requires CONFIG_ARM_LPAE enabled as all peripherals are located
above 4GB in the memory map.
Signed-off-by: Anders Berg <anders.berg@lsi.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- two fixes concerning iio ADC triggers for at91sam9260 and at91sam9g20
one for the "device" file, the other for the DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJTfjD/AAoJEAf03oE53VmQ1p0IAJL/FmsbXfHLLu8KvQEXMW8W
Y3c22v2mHSHpEFjqjFg+LbOkRbFaPTlszSXuKyw7HJPiOygUk/C1i2MUW4WLNlyY
fqu+tiAOrcfJ8rapM5ndFdeMZrkyRQIInFEPzOttQJSN4Aczpc6irfMqOOqw0y/s
Sf88MiK2YgeXnt5dH6mDYhy29glvspek3w1FmDN3DjmiAdxAUV8bSpOmw2FsFAX7
QJOwkevln+3Ddxnq+NsG/6KxdAl0fj+G3shl4GwALr+hizKypzsFsSGDuyKuAL2o
A7e+OFoUWN8eCTJBdP9YA/lVyl83uFMM3tBcHr4Oq8dJk6sQ0GNQcdJuCUBGTBw=
=ehhW
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes2' of git://github.com/at91linux/linux-at91 into fixes
Second 3.15 fixes for AT91
- two fixes concerning iio ADC triggers for at91sam9260 and at91sam9g20
one for the "device" file, the other for the DT.
* tag 'at91-fixes2' of git://github.com/at91linux/linux-at91:
ARM: at91: sam9260: fix compilation issues
ARM: at91/dt: sam9260: correct external trigger value
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Adds additional nodes to support GPLDO1-6 and VBUS regulators which
are now supported in the bcm590xx regulator driver.
Signed-off-by: Matt Porter <mporter@linaro.org>
Currently oscillator frequency is determined based on sysboot settings,
it may not be the case always. To determine it properly, efuse settings
also has to be read. CONTROL_STATUS register holds this information.
Bit 31: if 0, frequency to be determined based on sysboot
if 1, frequency to be determined based on efuse
Bit 29,30 - for efuse detection of frequency
Bit 22,23 - for sysboot detection of frequency
Add clock nodes (mux) to determine oscillator frequency as above.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
We need set-rate-parent flags for the display's clock path so that the
DSS driver can change the clock rate of the PLL.
This patchs adds the ti,set-rate-parent flag to disp_clk and
dpll_disp_m2_ck clock nodes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add ti,set-rate-parent to dss_dss_clk so that the DSS driver can
set the rate.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Booting Linux 3.14 on Pandaboard currently gets the following
message displayed:
smp_twd: clock not found -2
Define "mpu_periphclk" as the twd clock in omap4 dts to avoid this.
Signed-off-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
abe_iclk's parent is aess_fclk and not abe_clk.
Also correct the parameters for clock rate calculation as used for OMAP4
since in PRCM level there's no difference between the two platform
regarding to AESS/ABE clocking.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
In OMAP5 bit 8 in PRCM registers are not defined (Reserved) unlike their
counterpart in OMAP4.
It is better to not write to these bits.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
We need "tbclk" clock data for the functioning of ehrpwm
module. Hence, populating the required clock information
in clock dts file.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
tbclk does not need to be a composite clock, we can simply
use gate clock for this purpose.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Now that the reset code are part of drivers of their own, we need those in the
defconfig.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The init_machine hook is now at its default value. We can remove it.
Even though the sun4i and sun7i machines are nothing more than generic machines
now, leave them in so that we won't have to add them back if needed, and so
that the machine is still displayed in /proc/cpuinfo.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that reset is handled either by the watchdog driver for the sun4i, sun5i
and sun7i, and by a driver of its own for sun6i, we can remove it from the
platform code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add support for the 2 SDHC controllers on the DB8074 board. The first
controller (at 0xf9824900) is connected to an on board soldered eMMC.
The second controller (at 0xf98a4900) is connected to a uSD card slot.
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
The SoCFPGA has two watchdog timers. Add them to the dtsi.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
[dinh: modified patch to have correct irq flag]
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
The cycloneV has three gpio controllers, each one with 29 gpios. This patch
adds the three controller with the gpio driver which is now sitting the
gpio tree.
Cc: devicetree@vger.kernel.org
Acked-by: Alan Tull <atull@altera.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
This patch enables exynos_usbphy and hsotg device nodes.
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Kamil Debski <k.debski@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds a hsotg node for exynos4 USB2.0 device controller.
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Kamil Debski <k.debski@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch enables a exynos_usbphy node for exynos4 SoCs.
A exynos4x12 usb phy node is almost same with 4210's one
except compatible string and pmu syscon.
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds a PMU(Power Management Unit) syscon node. This
should be required for USB Phy syscon regmap I/F.
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
sss module device node missed clock macro.
This patch replace magic number with macro in clock
binding for exynos5420.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Phy and sss module device node missed clock macro.
This patch replace magic number with macros in clock
binding for exynos5250.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch replaces magic number of MIPI DSI Master node with
macros in clock binding for exynos4
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch enables support external SD card slot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch enables support for multimedia blocks - fimc in
mem2mem mode, no camera sensors support yet.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds device tree nodes necessary to enable USB support on
universalc210 board, this includes UDC controller (USB gadget) as well
as EHCI and OHCI host ports. LDO3 and LDO8 regulators are switched to
always on mode until EHCI and OHCI drivers will support them correctly.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds device tree nodes necessary to enable USB
gadget functionality on Exynos4210-based Trats board.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the audio subsystem clock controller and the I2S
IP block nodes for Exynos4 SoC series.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixed gpio key device node.
First, fix incorrect gpio property.
And then, add ok-key node where locate bottom center.
I have tested on exynos4412-trats2 board.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos4412-trats2 board have light/proximity sensor.
This patch add cm36651 light/ proximity sensor node for exynos4412.
cm36651 is required properties as below.
- Use i2c-gpio for cm36651 sensor.
- Use fixed regulator for the IR LED.
It is a part of the cm36651 for proximity detection.
- cm36651 is i2c device driver so need to use i2c-gpio driver.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add the pin control node and pin definitions of SPI8.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add missing PINCTRL selection. This enables selection of pinctrollers for
Qualcomm processors.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Separate Qualcomm low-level debugging UART to two options.
DEBUG_MSM_UART is used in earlier non-multi platform arches,
like MSM7X00A, QSD8X50 and MSM7X30.
DEBUG_QCOM_UARTDM is used in multi-plafrom arches and have
embedded data mover.
Make DEBUG_UART_PHYS and DEBUG_UART_BASE user adjustable by
Kconfig menu.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
As some of the IPs on Qualcomm SOCs are based on ARM PrimeCell IPs.
For example SDCC controller is PrimeCell MCI pl180. Adding this option will
give flexibility to reuse the existing drivers as it is without major
modifications.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Use the hexadecimal values for the triggers to match what is done for the device
tree. This also fixes compilation issues as the defines have been moved
elsewhere.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Now that DT based platforms are split out of mach-msm into
mach-qcom, put back a non-DT based SoC into the msm_defconfig and
stop selecting unsupported drivers.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This patch removes the selection of AT91_USE_OLD_CLK when selecting
sam9n12 SoC support. This will automatically enable COMMON_CLK_AT91 option
and add support for at91 common clk implementation.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define sam9n12ek's main and slow crystal frequencies.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define sam9n12 clocks and make use of them in peripheral definitions.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch encloses sam9n12 old clk registration in
"#if defined(CONFIG_OLD_CLK_AT91) #endif" sections.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch removes the selection of AT91_USE_OLD_CLK when selecting
sam9x5 SoCs support. This will automatically enable COMMON_CLK_AT91 option
and add support for at91 common clk implementation.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define sam9x5ek's main and slow crystal frequencies.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define sam9x5 clocks in sam9x5 dt files and make use of them in peripheral
definitions.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch encloses sam9x5 old clk registration in
"#if defined(CONFIG_OLD_CLK_AT91) #endif" sections.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
In the refactoring of the coherency fabric assembly code, a function
called ll_get_cpuid() was created to factorize common logic between
functions adding CPU to the SMP coherency group, enabling and
disabling the coherency.
However, the name of the function is highly misleading: ll_get_cpuid()
makes one think tat it returns the ID of the CPU, i.e 0 for CPU0, 1
for CPU1, etc. In fact, this is not at all what this function returns:
it returns a CPU mask for the current CPU, usable for the coherency
fabric configuration and control registers.
Therefore this commit renames this function to
ll_get_coherency_cpumask(), and adds additional comments on top of the
function to explain in more details what it does, and also how the
endianess issue is handled.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1400762882-10116-5-git-send-email-thomas.petazzoni@free-electrons.com
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit makes no functional change, it only improves a bit the
various code comments in mach-mvebu/coherency_ll.S, by fixing a few
typos and adding a few more details.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1400762882-10116-4-git-send-email-thomas.petazzoni@free-electrons.com
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit does not make any functional change, it only fixes the
indentation of a few assembly instructions in
arch/arm/mach-mvebu/coherency_ll.S.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1400762882-10116-3-git-send-email-thomas.petazzoni@free-electrons.com
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
As part of the introduction of the cpuidle support for Armada XP, the
coherency code was significantly reworked, especially in the
coherency_ll.S file. However, when the ll_get_cpuid function was
created, the big-endian specific code that switches the endianess of
the register was not updated properly.
This patch fixes this code, and therefore makes big endian systems
bootable again.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1400762882-10116-2-git-send-email-thomas.petazzoni@free-electrons.com
Fixes: 2e8a5942f8 ("ARM: mvebu: Split low level functions to manipulate HW coherency")
Reported-by: Kevin Hilman <khilman@linaro.org>
Cc: Kevin Hilman <khilman@linaro.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Commit b0063aad5d ("ARM: mvebu: use hardware I/O coherency also for
PCI devices") added a reference to the pci_bus_type variable, but this
variable is only available when CONFIG_PCI is enabled. Therefore,
there is now a build failure in !CONFIG_PCI situations.
This commit fixes that by enclosing the entire initcall into a
IS_ENABLED(CONFIG_PCI) condition.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1400598783-706-1-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Due a copy/paste error, the 'reg' values for the third PCIe interface
on Armada 380, and the third and fourth PCIe interfaces on Armada 385
are wrong: they are equal to the one of the second PCIe interface.
This patch fixes this by using the appropriate 'reg' values for those
PCIe interfaces.
Without this fix, the third and fourth PCIe interfaces are unusable on
those platforms.
Reported-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1400597008-4148-1-git-send-email-thomas.petazzoni@free-electrons.com
Fixes: 0d3d96ab00 ("ARM: mvebu: add Device Tree description of the Armada 380/385 SoCs")
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Marvell Armada 375 and Armada 38x SOCs, which use the Cortex-A9
CPU core, the PL310 cache and the Marvell PCIe hardware block are
affected a L2/PCIe deadlock caused by a system erratum when hardware
I/O coherency is used.
This deadlock can be avoided by mapping the PCIe memory areas as
strongly-ordered (note: MT_UNCACHED is strongly-ordered), and by
removing the outer cache sync done in software. This is implemented in
this patch by:
* Registering a custom arch_ioremap_caller function that allows to
make sure PCI memory regions are mapped MT_UNCACHED.
* Adding at runtime the 'arm,io-coherent' property to the PL310 cache
controller. This cannot be done permanently in the DT, because the
hardware I/O coherency can only be enabled when CONFIG_SMP is
enabled, in the current kernel situation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1400165974-9059-4-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Kconfig symbol USB_MUSB_PERIPHERAL was removed in v3.1. The last two
checks for its macro now always evaluate to false. So remove these
checks.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
[nsekhar@ti.com: also cleaned-up usage in defconfig file]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The i12 tvbox is an A20 based android tvbox, with 512M / 1G RAM, 4G nand flash,
ap6210 or ap6330 sdio wifi + bt (broadcom sdio wifi + uart attached brcm bt),
2USB host ports using USB-A receptacles and a micro-usb receptacle for USB OTG,
and 100Mbit ethernet using an IP101a phy.
The PCB is labelled i12-a20 hence I've named the board i12-a20. It is used
in noname allwinner A20 tv-boxes, which are sometimes sold with Q5 or
QT840A as product name.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
bus-width defaults to 1, and all 4 lines are hooked up at the cubietruck,
properly set bus-width to 4.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The following parameters are no longer needed by the edma driver since the
information can be obtained from the IP's CCCFG register:
n_channel, n_region, n_slot and n_tc.
Remove the initialization of n_cc as well since in this context it has no
meaning. We have separate edma_soc_info struct/eDMA3_CC instance so this
member does not make any sense (and the driver no longer uses it).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
dma-channels, ti,edma-regions and ti,edma-slots no longer needed in DT since
the the same information is available in the IP's CCCFG register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
dma-channels, ti,edma-regions and ti,edma-slots no longer needed in DT since
the the same information is available in the IP's CCCFG register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
From CCCFG register of eDMA3 we can get all the needed information for the
driver about the IP:
Number of channels: NUM_DMACH
Number of regions: NUM_REGN
Number of slots (PaRAM sets): NUM_PAENTRY
Number of TC/EQ: NUM_EVQUE
In case when booted with DT or the queue_priority_mapping is not provided
set up a default priority map.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
To be consistent in the code that we take parameters from edma_cc[j] struct
and not randomly from info[j] as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The struct edma is allocated per CC bases so the member num_cc does not make
any sense. One CC is one CC, it does not have sub CCs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The Colombus has a full size SD slot wired to the MMC0 controller. In order to
work, the MMC lines have to have the pull-ups enabled though.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The unit-address doesn't match the reg property. Since the reg property is
correct, change the unit-address accordingly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The colombus board has a on-board USB hub, that is enabled through the pin
PH24, and wired to the first EHCI controller.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- exynos4
: add missing pinctrls
- exynos4412-trats2
: update camera nodes and add rear camera nodes
: rename alias for i2c_ak8975 label
Update camera nodes for exynos4 and exynos4412-trats2
- exynos5250
: update DWC3 usb controller and enable to use generic USB DRD phy
- exynos5250-snow
: enable dp-controller, fimd, hdmi and pwm backlight
: add sound node and Vbus regulator for USB 3.0
: add tps65090 power regulator
: add pinctrl for EC irq and i2c-arbitrator
- exynos5420
: change to correct compatible string for hdmi
: add PD entry to MFC codec and enable DWC3 and USB 3.0 PHY
: add MFC memory banks for smdk5420 and arndale-octa boards
- exynos5420-peach-pit
: add support exynos5420 based peach-pit board
: add sound node and Vbus regulatro for USB 3.0
: enable dp-controller, fimd
- exynos5420-smdk5420
: add Vbus regulatro for USB 3.0
- use generic DT bindings for map SYSRAM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=F8WL
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Samsung DT updates for v3.16
- exynos4
: add missing pinctrls
- exynos4412-trats2
: update camera nodes and add rear camera nodes
: rename alias for i2c_ak8975 label
Update camera nodes for exynos4 and exynos4412-trats2
- exynos5250
: update DWC3 usb controller and enable to use generic USB DRD phy
- exynos5250-snow
: enable dp-controller, fimd, hdmi and pwm backlight
: add sound node and Vbus regulator for USB 3.0
: add tps65090 power regulator
: add pinctrl for EC irq and i2c-arbitrator
- exynos5420
: change to correct compatible string for hdmi
: add PD entry to MFC codec and enable DWC3 and USB 3.0 PHY
: add MFC memory banks for smdk5420 and arndale-octa boards
- exynos5420-peach-pit
: add support exynos5420 based peach-pit board
: add sound node and Vbus regulatro for USB 3.0
: enable dp-controller, fimd
- exynos5420-smdk5420
: add Vbus regulatro for USB 3.0
- use generic DT bindings for map SYSRAM
[olof: Fixed up conflict with a fix for 4212 secondary CPU startup, carrying
over the fix to the reworked code]
* tag 'samsung-dt' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (32 commits)
ARM: dts: Add MFC memory banks to exynos5420 boards
ARM: dts: enable dp-controller for exynos5420-peach-pit board
ARM: dts: enable fimd for exynos5420 based peach-pit board
ARM: dts: enable dp-controller for exynos5250-snow board
ARM: dts: enable fimd for exynos5250-snow board
ARM: dts: enable pwm backlight for exynos5250-snow
ARM: dts: Add pwmX_out pinctrl nodes to exynos5250
ARM: dts: Add Vbus regulator for USB 3.0 on exynos5420-smdk5420
ARM: dts: Add Vbus regulator for USB 3.0 on exynos5420-peach-pit
ARM: dts: Add Vbus regulator for USB 3.0 on exynos5250-snow
ARM: dts: Add PD entry to MFC codec on exynos5420
ARM: dts: Add sound node for exynos5420-peach-pit board
ARM: dts: Add sound node for exynos5250-snow board
ARM: dts: Update DWC3 usb controller to use new phy driver for exynos5250
ARM: dts: Enable support for generic USB DRD phy for exynos5250
ARM: dts: Enable support for DWC3 controller for exynos5420
ARM: dts: Enable support for USB 3.0 PHY controller for exynos5420
ARM: dts: enable hdmi for exynos5420-peach-pit board
ARM: dts: change to correct compatible string for exynos5420 hdmi
ARM: dts: enable hdmi for exynos5250 based snow board
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merging in Samsung fixes for 3.15-rc to avoid an annoying context conflict
with new DT code.
* commit '702b691e4a71':
ARM: dts: Remove g2d_pd node for exynos5420
ARM: dts: Remove mau_pd node for exynos5420
ARM: exynos_defconfig: enable HS-I2C to fix for mmc partition mount
ARM: dts: disable MDMA1 node for exynos5420
ARM: EXYNOS: fix the secondary CPU boot of exynos4212
Signed-off-by: Olof Johansson <olof@lixom.net>
- S3C2412, S3C2413, S3C2416 and S3C2443 to use CCF
- S3C2410, S3C2440, S3C2442 to use CCF
- Remove legacy samsung clock from mach-s3c24xx/
- Some of them are missed from previous pull-request
- Clock related sutff got ack from Mike and Tomasz
- Created the last commit due to missing changes
during re-sorting because this branch is provided
as a base to samsung clk tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJTeoP9AAoJEA0Cl+kVi2xq+VQP/jKVZmd0FvMeoyoyddUfOxfV
b8jKaVbD/lB7vhPc7XGK9waXBdi6Ajdx71VAAfIfcl+m+xp9XTS0eVirWeP9yh6g
Xbtqp6QhWJfph1iufI/Tmab075lmHI05iprVP3LIJ8fFVpfHbbMLel9SJEDti+sj
+shdWgTdd4Cxl7Y60noo7Y4WEBrC2qpkegC0xut16ZJKdt5WxC4KW2DltC435MB0
b/v7oKLvWr2SvBkDKk7h5aX7z+Ws3ALQ2XfV/CbTkW9LaPFaPqr68V9ZNmHEfeLb
Az7aSlktBAAGTjwDHYOuw5w1eHHrZZBOpJfVKFmPVLGNzqkTAzUWMDQJay/LTRDF
u9fXtJA2cZBuNmuGdAiE8ZxQwbrLFiPC06Ybie+Qq4LiliCzjBfuB+CuSf7bVw2A
jOmU34Cctvyj7JdEZzDDby4baQFgS6NuI5OHnTXjQlfNejtoG0gDSIWWkPm5xr1w
c5ADCyq5UzBCmUzhp4KCyxMnqz9BGMxw96PPLKGAlNNw0i1tp8SUFjzaKyDB6yOm
I60WDNWGC+T4uoNRvkW8sKGQX7thjtR5KVI0cWvgQbBSiycMoMJcKWAmrckGA1In
SPnriO5NpDIOEnV7MQ8pyPLIijhX09xSdDS7wASR9rthC7qnnHmVBjByMQXUi6Th
emxN1xC5mM2kT68u/oWB
=HX4t
-----END PGP SIGNATURE-----
Merge tag 's3c24xx-clk' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
Merge "Samsung S3C24XX updates for 3.16" from Kukjin Kim:
Samsung S3C24XX to use the common clock framework
- S3C2412, S3C2413, S3C2416 and S3C2443 to use CCF
- S3C2410, S3C2440, S3C2442 to use CCF
- Remove legacy samsung clock from mach-s3c24xx/
- Some of them are missed from previous pull-request
- Clock related sutff got ack from Mike and Tomasz
- Created the last commit due to missing changes
during re-sorting because this branch is provided
as a base to samsung clk tree.
* tag 's3c24xx-clk' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (23 commits)
ARM: S3C24XX: fix merge conflict
ARM: S3C24XX: remove SAMSUNG_CLOCK remnants after ccf conversion
ARM: S3C24XX: remove legacy clock code
ARM: S3C24XX: convert s3c2410 to common clock framework
ARM: S3C24XX: convert s3c2440 and s3c2442 to common clock framework
ARM: S3C24XX: add platform code for conversion to the common clock framework
clk: samsung: add clock controller driver for s3c2410, s3c2440 and s3c2442
dt-bindings: add documentation for s3c2410 clock controller
ARM: S3C24XX: enable usage of common dclk if common clock framework is enabled
clk: samsung: add clock driver for external clock outputs
ARM: S3C24XX: cpufreq-utils: don't write raw values to MPLLCON when using ccf
ARM: S3C24XX: convert s3c2412 to common clock framework
clk: samsung: add clock controller driver for s3c2412
dt-bindings: add documentation for s3c2412 clock controller
clk: samsung: add plls used by the early s3c24xx cpus
ARM: S3C24XX: only store clock registers when old clock code is active
ARM: S3C24XX: Convert s3c2416 and s3c2443 to common clock framework
ARM: dts: add clock data for s3c2416
ARM: S3C24XX: prevent conflicts between ccf and non-ccf s3c24xx-socs
clk: samsung: add clock-driver for s3c2416, s3c2443 and s3c2450
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Also a minor one line fix for audio clock on 54xx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ioRt
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.15/fixes-v3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Pull "omap fixes for v3.15-rc cycle" from Tony Lindgren:
Regression fixes for omaps for NAND, DMA, cpu_idle and audio.
Also a minor one line fix for audio clock on 54xx.
* tag 'omap-for-v3.15/fixes-v3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: Fix the boot regression with CPU_IDLE enabled
ARM: OMAP2+: Fix DMA hang after off-idle
ARM: OMAP2+: nand: Fix NAND on OMAP2 and OMAP3 boards
ARM: omap5: hwmod_data: Correct IDLEMODE for McPDM
ARM: OMAP3: clock: Back-propagate rate change from cam_mclk to dpll4_m5 on all OMAP3 platforms
Signed-off-by: Olof Johansson <olof@lixom.net>
It is ignored by the edma driver since we are just setting back the default
mapping of TC -> Queue.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
There is no need to change the default TC -> Queue mapping. By default the
mapping is: TC0 -> Q0, TC1 -> Q1, etc.
Changing this has no benefits at all and all the board files are just setting
the same mapping back to the HW.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Instead of saving the for loop length, take the num_tc value from the pdata.
In case of DT boot set the n_tc to 3 as it is hardwired in edma_of_parse_dt()
This is a temporary state since upcoming patch(es) will change how we are
dealing with these parameters.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The pdata has been just allocated with devm_kzalloc() in
edma_setup_info_from_dt() and passed to this function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
If we fail to allocate struct platform_device pdev we
dereference it after the goto label err.
This bug was found using coccinelle.
Fixes: afa77ef (ARM: mx3: dynamically allocate "ipu-core" devices)
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Remove g2d_pd and mau_pd nodes on exynos5420.
Since the power domains are linked to the CMU blocks,
kernel panic happens during access clocks when the
power domains are disabled. Now this is a best solution.
- Enable HS-I2C on exynos5 by default
MMC partition cannot be mounted for RFS without the
enabling HS-I2C because regulators for MMC power are
connected to HS-I2C bus.
- Disable MDMA1 node on exynos5420
When MDMA1 runs in secure mode it makes kernel fault,
so need to disalbe it on exynos5420 by default instead
of each board.
- Fix the secondary CPU boot for exynos4212
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=kz4r
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Samsung fixes for 3.15 from Kukjin Kim:
- Remove g2d_pd and mau_pd nodes on exynos5420.
Since the power domains are linked to the CMU blocks,
kernel panic happens during access clocks when the
power domains are disabled. Now this is a best solution.
- Enable HS-I2C on exynos5 by default
MMC partition cannot be mounted for RFS without the
enabling HS-I2C because regulators for MMC power are
connected to HS-I2C bus.
- Disable MDMA1 node on exynos5420
When MDMA1 runs in secure mode it makes kernel fault,
so need to disalbe it on exynos5420 by default instead
of each board.
- Fix the secondary CPU boot for exynos4212
* tag 'samsung-fixes' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Remove g2d_pd node for exynos5420
ARM: dts: Remove mau_pd node for exynos5420
ARM: exynos_defconfig: enable HS-I2C to fix for mmc partition mount
ARM: dts: disable MDMA1 node for exynos5420
ARM: EXYNOS: fix the secondary CPU boot of exynos4212
Signed-off-by: Olof Johansson <olof@lixom.net>
Get the two interrupt line number at the same time by merging the two
instance of if(node){}else{} places.
replace the &pdev->dev with the already existing dev which makes it possible
to collapse lines with devm_request_irq()
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
