- replace rtl8168g-1.fw with rtl8168g-2.fw which support new method.
- fix PHY power down is useless.
- disable rx early which causes the rx abnormal.
- enable auto fifo.
- set 10M IFG to default value.
- fix the conflict between jumbo frame and flow control.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove useless action PHY_READ_EFUSE, PHY_READ_MAC_BYTE, PHY_WRITE_MAC_BYTE,
PHY_WRITE_ERI_WORD. And define the new action PHY_MDIO_CHG.
PHY_MDIO_CHG is used to modify the mdio operation. By the way, the
firmware could support setting mac ocp.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the new settings and correct the wrong settings.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the current settings with rtl_writephy and rtl_readphy.
For the hardware, the settings are same with previous ones. This
make the setting method like the previous chips.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some codes are belong to binary codes and should be removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It would cause no link after suspending or shutdowning when the
nic changes the speed to 10M and connects to a link partner which
forces the speed to 100M.
Check the link partner ability to determine which speed to set.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emitting netdev_alloc_skb and netdev_alloc_skb_ip_align OOM
messages is unnecessary as there is already a dump_stack
after allocation failures.
Other trivial changes around these removals:
Convert a few comparisons of pointer to 0 to !pointer.
Change flow to remove unnecessary label.
Remove now unused variable.
Hoist assignment from if.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hardware start settings implicitely assume an usual 1500 bytes mtu
that can't be guaranteed because changes of mtu may be requested both
before and after the hardware is started.
Reported-by: Tomi Orava <tomimo@ncircle.nullnet.fi>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
The bnx2x gso_type setting bug fix in 'net' conflicted with
changes in 'net-next' that broke the gso_* setting logic
out into a seperate function, which also fixes the bug in
question. Thus, use the 'net-next' version.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d64ec84151.
Jörg Otte reported his 8168evl to increase boot time link detection
from 1.6 to 10 s.
Hayes suggests reverting it for the time being.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Jörg Otte <jrg.otte@gmail.com>
This reverts commit e0c0755779.
Jörg Otte reported his 8168evl to fail boot time link detection.
Hayes suggests reverting it for the time being.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Jörg Otte <jrg.otte@gmail.com>
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
Control of receive descriptor must not be returned to ethernet chipset
before vlan tag processing is done.
VLAN tag receive word is now reset both in normal and error path.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Spotted-by: Timo Teras <timo.teras@iki.fi>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was introduced in commit 6dccd16 "r8169: merge with version
6.001.00 of Realtek's r8169 driver". I did not find the version
6.001.00 online, but in 6.002.00 or any later r8169 from Realtek
this hunk is no longer present.
Also commit 05af214 "r8169: fix Ethernet Hangup for RTL8110SC
rev d" claims to have fixed this issue otherwise.
The magic compare mask of 0xfffe000 is dubious as it masks
parts of the Reserved part, and parts of the VLAN tag. But this
does not make much sense as the VLAN tag parts are perfectly
valid there. In matter of fact this seems to be triggered with
any VLAN tagged packet as RxVlanTag bit is matched. I would
suspect 0xfffe0000 was intended to test reserved part only.
Finally, this hunk is evil as it can cause more packets to be
handled than what was NAPI quota causing net/core/dev.c:
net_rx_action(): WARN_ON_ONCE(work > weight) to trigger, and
mess up the NAPI state causing device to hang.
As result, any system using VLANs and having high receive
traffic (so that NAPI poll budget limits rtl_rx) would result
in device hang.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 6f0333b ("r8169: use 50% less ram for RX ring") the rx
ring buffers are always copied making dirty_rx useless.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: "David S. Miller" <davem@davemloft.net>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David S. Miller <davem@davemloft.net>
perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit: cb64edb6b8 upstream
Above commit may introduce a race between cp_interrupt and dev_close
/ change MTU / dev_open up state. Changes cp_interrupt to tolerate
this. Change spin_locking in cp_interrupt to avoid possible
but unobserved race.
Reported-by: "Francois Romieu" <romieu@fr.zoreil.com>
Tested on virtual hardware, Tx MTU size up to 4096, max tx payload
was ping -s 4068 for MTU of 4096. No real hardware, need test
assist.
Signed-off-by: "John Greene" <jogreene@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: "David Woodhouse" <David.Woodhouse@intel.com>
Tested-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking changes from David Miller:
1) Allow to dump, monitor, and change the bridge multicast database
using netlink. From Cong Wang.
2) RFC 5961 TCP blind data injection attack mitigation, from Eric
Dumazet.
3) Networking user namespace support from Eric W. Biederman.
4) tuntap/virtio-net multiqueue support by Jason Wang.
5) Support for checksum offload of encapsulated packets (basically,
tunneled traffic can still be checksummed by HW). From Joseph
Gasparakis.
6) Allow BPF filter access to VLAN tags, from Eric Dumazet and
Daniel Borkmann.
7) Bridge port parameters over netlink and BPDU blocking support
from Stephen Hemminger.
8) Improve data access patterns during inet socket demux by rearranging
socket layout, from Eric Dumazet.
9) TIPC protocol updates and cleanups from Ying Xue, Paul Gortmaker, and
Jon Maloy.
10) Update TCP socket hash sizing to be more in line with current day
realities. The existing heurstics were choosen a decade ago.
From Eric Dumazet.
11) Fix races, queue bloat, and excessive wakeups in ATM and
associated drivers, from Krzysztof Mazur and David Woodhouse.
12) Support DOVE (Distributed Overlay Virtual Ethernet) extensions
in VXLAN driver, from David Stevens.
13) Add "oops_only" mode to netconsole, from Amerigo Wang.
14) Support set and query of VEB/VEPA bridge mode via PF_BRIDGE, also
allow DCB netlink to work on namespaces other than the initial
namespace. From John Fastabend.
15) Support PTP in the Tigon3 driver, from Matt Carlson.
16) tun/vhost zero copy fixes and improvements, plus turn it on
by default, from Michael S. Tsirkin.
17) Support per-association statistics in SCTP, from Michele
Baldessari.
And many, many, driver updates, cleanups, and improvements. Too
numerous to mention individually.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
net/mlx4_en: Add support for destination MAC in steering rules
net/mlx4_en: Use generic etherdevice.h functions.
net: ethtool: Add destination MAC address to flow steering API
bridge: add support of adding and deleting mdb entries
bridge: notify mdb changes via netlink
ndisc: Unexport ndisc_{build,send}_skb().
uapi: add missing netconf.h to export list
pkt_sched: avoid requeues if possible
solos-pci: fix double-free of TX skb in DMA mode
bnx2: Fix accidental reversions.
bna: Driver Version Updated to 3.1.2.1
bna: Firmware update
bna: Add RX State
bna: Rx Page Based Allocation
bna: TX Intr Coalescing Fix
bna: Tx and Rx Optimizations
bna: Code Cleanup and Enhancements
ath9k: check pdata variable before dereferencing it
ath5k: RX timestamp is reported at end of frame
ath9k_htc: RX timestamp is reported at end of frame
...
GigaMAC registers have been reported left unitialized in several
situations:
- after cold boot from power-off state
- after S3 resume
Tweaking rtl_hw_phy_config takes care of both.
This patch removes an excess entry (",") at the end of the exgmac_reg
array as well.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Wang YanQing <udknight@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a series of patches that remove the dev* attributes for all
networking drivers, with the exception of wireless drivers, those are in
a different branch.
Use of __devinit, __devexit_p, __devinitdata, __devinitconst, and
__devexit are no longer needed since CONFIG_HOTPLUG is being removed as
an option.
Note, there are some devinit compiler section mismatch warnings due to
this series, but they are fixed up when merged with my driver-next
branch, which fixes the PCI device id warnings, and removes the modpost
detection, as it's no longer needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlC9COEACgkQMUfUDdst+ykOEgCeKZsrtKrbjMFM5jEROqnk33FI
SwEAoMSZWFJ7M1/27FGRkylmmypWXi/p
=HH3A
-----END PGP SIGNATURE-----
Merge tag 'dev_removal' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/net-next
Networking: Remove __dev* markings from the networking drivers
This is a series of patches that remove the dev* attributes for all
networking drivers, with the exception of wireless drivers, those are in
a different branch.
Use of __devinit, __devexit_p, __devinitdata, __devinitconst, and
__devexit are no longer needed since CONFIG_HOTPLUG is being removed as
an option.
Note, there are some devinit compiler section mismatch warnings due to
this series, but they are fixed up when merged with my driver-next
branch, which fixes the PCI device id warnings, and removes the modpost
detection, as it's no longer needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8139cp driver has a change_mtu function that has not been
enabled since the dawn of the git repository. However, the
generic eth_change_mtu is not used in its place, so that
invalid MTU values can be set on the interface.
Original patch salvages the broken code for the single case of
setting the MTU while the interface is down, which is safe
and also includes the range check. Now enhanced to support up
or down interface.
v2: fix case where rxbufsz isn't changed in the up state case
Original patch from
http://lkml.indiana.edu/hypermail/linux/kernel/1202.2/00770.html
Testing: has been test on virtual 8139cp setup without issue,
have no access real hardware 8139cp, need testing help.
Signed-off-by: "John Greene" <jogreene@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
cp_open
[...]
rc = cp_alloc_rings(cp);
if (rc)
return rc;
cp_alloc_rings
[...]
mem = dma_alloc_coherent(&cp->pdev->dev, CP_RING_BYTES,
&cp->ring_dma, GFP_KERNEL);
- cp_alloc_rings never frees the coherent mapping it allocates
- neither do cp_open when cp_alloc_rings fails
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recovery doesn't work too well if we leave interrupts disabled...
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for byte queue limits on RTL8139C+
Tested on real hardware.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-By: Dave Täht <dave.taht@bufferbloat.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes (for me) a regression introduced by commit b01af457 ("8139cp:
set ring address before enabling receiver"). That commit configured the
descriptor ring addresses earlier in the initialisation sequence, in
order to avoid the possibility of triggering stray DMA before the
correct address had been set up.
Unfortunately, it seems that the hardware will scribble garbage into the
TxRingAddr registers when we enable "plus mode" Tx in the CpCmd
register. Observed on a Traverse Geos router board.
To deal with this, while not reintroducing the problem which led to the
original commit, we augment cp_start_hw() to write to the CpCmd register
*first*, then set the descriptor ring addresses, and then finally to
enable Rx and Tx in the original 8139 Cmd register. The datasheet
actually indicates that we should enable Tx/Rx in the Cmd register
*before* configuring the descriptor addresses, but that would appear to
re-introduce the problem that the offending commit b01af457 was trying
to solve. And this variant appears to work fine on real hardware.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org [3.5+]
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit b26623dab7.
This reverts the revert, in net-next we'll try another scheme
to fix this bug using patches from David Woodhouse.
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/iwlwifi/pcie/tx.c
Minor iwlwifi conflict in TX queue disabling between 'net', which
removed a bogus warning, and 'net-next' which added some status
register poking code.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts b01af4579e.
The original patch was tested with emulated hardware. Real
hardware chokes.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=47041
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since eab6d18d (vlan: Don't check for vlan group before
vlan_tx_tag_present.) we don't check tp->vlgrp and thus
tp is not needed in this function.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
The following chips need to enable internal settings to let ASPM
and clock request work.
RTL8111E-VL, RTL8111F, RTL8411, RTL8111G
RTL8105, RTL8402, RTL8106
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building atp.o triggers this GCC warning:
drivers/net/ethernet/realtek/atp.c: In function ‘set_rx_mode’:
drivers/net/ethernet/realtek/atp.c:871:26: warning: ‘mc_filter[0]’ may be used uninitialized in this function [-Wuninitialized]
GCC is correct. In promiscuous mode 'mc_filter' will be used
uninitialized in set_rx_mode_8012(), which is apparently inlined into
set_rx_mode().
But it turns out set_rx_mode_8012() will never be called, since
net_local.chip_type will always be RTL8002. So we can just remove
set_rx_mode_8012() and do some related cleanups.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL_GIGA_MAC_VER_35 includes no multicast hardware filter.
Signed-off-by: Nathan Walp <faceprint@faceprint.com>
Suggested-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This regression was spotted between Debian squeeze and Debian wheezy
kernels (respectively based on 2.6.32 and 3.2). More info about
Wake-on-LAN issues with Realtek's 816x chipsets can be found in the
following thread: http://marc.info/?t=132079219400004
Probable regression from d4ed95d796e5126bba51466dc07e287cebc8bd19;
more chipsets are likely affected.
Tested on top of a 3.2.23 kernel.
Reported-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Tested-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Hinted-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Cyril Brulebois <kibi@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After d58d46b5 (r8169: jumbo fixes.) max frame len is stored in
rtl_chip_infos[].jumbo_max for each chip and SafeMtu should be gone.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
use the module_pci_driver macro to make the code simpler
by eliminating the module_init and module_exit calls
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable ALDPS function to save power when link down. Note that the
feature should be set after the other PHY settings. And the firmware
is necessary. Don't enable it without loading the firmware.
None of the firmware-free chipsets support ALDPS. Neither do the
RTL8168d/8111d.
For 8136 series, make sure the ALDPS is disabled before loading the
firmware. For 8168 series, the ALDPS would be disabled automatically
when loading firmware. You must not disable it directly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current GRO can hold packets in gro_list for almost unlimited
time, in case napi->poll() handler consumes its budget over and over.
In this case, napi_complete()/napi_gro_flush() are not called.
Another problem is that gro_list is flushed in non friendly way :
We scan the list and complete packets in the reverse order.
(youngest packets first, oldest packets last)
This defeats priorities that sender could have cooked.
Since GRO currently only store TCP packets, we dont really notice the
bug because of retransmits, but this behavior can add unexpected
latencies, particularly on mice flows clamped by elephant flows.
This patch makes sure no packet can stay more than 1 ms in queue, and
only in stress situations.
It also complete packets in the right order to minimize latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking changes from David Miller:
1) GRE now works over ipv6, from Dmitry Kozlov.
2) Make SCTP more network namespace aware, from Eric Biederman.
3) TEAM driver now works with non-ethernet devices, from Jiri Pirko.
4) Make openvswitch network namespace aware, from Pravin B Shelar.
5) IPV6 NAT implementation, from Patrick McHardy.
6) Server side support for TCP Fast Open, from Jerry Chu and others.
7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel
Borkmann.
8) Increate the loopback default MTU to 64K, from Eric Dumazet.
9) Use a per-task rather than per-socket page fragment allocator for
outgoing networking traffic. This benefits processes that have very
many mostly idle sockets, which is quite common.
From Eric Dumazet.
10) Use up to 32K for page fragment allocations, with fallbacks to
smaller sizes when higher order page allocations fail. Benefits are
a) less segments for driver to process b) less calls to page
allocator c) less waste of space.
From Eric Dumazet.
11) Allow GRO to be used on GRE tunnels, from Eric Dumazet.
12) VXLAN device driver, one way to handle VLAN issues such as the
limitation of 4096 VLAN IDs yet still have some level of isolation.
From Stephen Hemminger.
13) As usual there is a large boatload of driver changes, with the scale
perhaps tilted towards the wireless side this time around.
Fix up various fairly trivial conflicts, mostly caused by the user
namespace changes.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits)
hyperv: Add buffer for extended info after the RNDIS response message.
hyperv: Report actual status in receive completion packet
hyperv: Remove extra allocated space for recv_pkt_list elements
hyperv: Fix page buffer handling in rndis_filter_send_request()
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
hyperv: Fix the max_xfer_size in RNDIS initialization
vxlan: put UDP socket in correct namespace
vxlan: Depend on CONFIG_INET
sfc: Fix the reported priorities of different filter types
sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP
sfc: Fix loopback self-test with separate_tx_channels=1
sfc: Fix MCDI structure field lookup
sfc: Add parentheses around use of bitfield macro arguments
sfc: Fix null function pointer in efx_sriov_channel_type
vxlan: virtual extensible lan
igmp: export symbol ip_mc_leave_group
netlink: add attributes to fdb interface
tg3: unconditionally select HWMON support when tg3 is enabled.
Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT"
gre: fix sparse warning
...
The r8169 driver currently limits the DMA burst for TX to 1024 bytes. I have
a box where this prevents the interface from using the gigabit line to its full
potential. This patch solves the problem by setting TX_DMA_BURST to unlimited.
The box has an ASRock B75M motherboard with on-board RTL8168evl/8111evl
(XID 0c900880). TSO is enabled.
I used netperf (TCP_STREAM test) to measure the dependency of TX throughput
on MTU. I did it for three different values of TX_DMA_BURST ('5'=512, '6'=1024,
'7'=unlimited). This chart shows the results:
http://michich.fedorapeople.org/r8169/r8169-effects-of-TX_DMA_BURST.png
Interesting points:
- With the current DMA burst limit (1024):
- at the default MTU=1500 I get only 842 Mbit/s.
- when going from small MTU, the performance rises monotonically with
increasing MTU only up to a peak at MTU=1076 (908 MBit/s). Then there's
a sudden drop to 762 MBit/s from which the throughput rises monotonically
again with further MTU increases.
- With a smaller DMA burst limit (512):
- there's a similar peak at MTU=1076 and another one at MTU=564.
- With unlimited DMA burst:
- at the default MTU=1500 I get nice 940 Mbit/s.
- the throughput rises monotonically with increasing MTU with no strange
peaks.
Notice that the peaks occur at MTU sizes that are multiples of the DMA burst
limit plus 52. Why 52? Because:
20 (IP header) + 20 (TCP header) + 12 (TCP options) = 52
The Realtek-provided r8168 driver (v8.032.00) uses unlimited TX DMA burst too,
except for CFG_METHOD_1 where the TX DMA burst is set to 512 bytes.
CFG_METHOD_1 appears to be the oldest MAC version of "RTL8168B/8111B",
i.e. RTL_GIGA_MAC_VER_11 in r8169. Not sure if this MAC version really needs
the smaller burst limit, or if any other versions have similar requirements.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one includes a 8168. Not to be confused with the sky2 driven
one whose PCI vendor and device ID are the same.
Reported-by: Neyuki Inaya <in@joblog.ru>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, when we turned on the "Enable No Snoop Bit," we cleared all
the other Device Control bits, including error reporting enables,
Max_Payload_Size, Max_Read_Request_Size, etc. This patch preserves
all the other bits.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit 036dafa28d.
First it appears in bisection, then reverting it solves the usual
netdev watchdog problem for different people. I don't have a proper
fix yet so get rid of it.
Bisected-and-reported-by: Alex Villacís Lasso <a_villacis@palosanto.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not needed for mac_ocp_{write / read}. Actually bit 31 of OCPDR
does not change and r8168_mac_ocp_read always returns ~0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Tested-by: Francois Romieu <romieu@fr.zoreil.com>
For RTL8111G, the settings of phy and firmware are replaced with
ocp functions. r8168g_mdio_{write / read} redirects the relative
settings to suitable ocp functions. A per-device variable is needed
to evaluate the real address of ocp functions.
rtl_writephy(tp, 0x1f, xxxx) is dedicated to keeping said variable
up-to-date.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Twelve functions can fail silently. Now they have a chance to complain.
Macro and pasting abuse has been kept at a level where tags and
friends should not be hurt.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The 8168evl (RTL_GIGA_MAC_VER_34) based Gigabyte GA-990FXA motherboards
are very prone to NETDEV watchdog problems without this change. See
https://bugzilla.kernel.org/show_bug.cgi?id=42899 for instance.
I don't know why it *works*. It's depressingly effective though.
For the record:
- the problem may go along IOMMU (AMD-Vi) errors but it really looks
like a red herring.
- the patch sets the RX_MULTI_EN bit. If the 8168c doc is any guide,
the chipset now fetches several Rx descriptors at a time.
- long ago the driver ignored the RX_MULTI_EN bit.
e542a2269f changed the RxConfig
settings. Whatever the problem it's now labeled a regression.
- Realtek's own driver can identify two different 8168evl devices
(CFG_METHOD_16 and CFG_METHOD_17) where the r8169 driver only
sees one. It sucks.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reworking the r8169 driver a few months ago to perform the
smallest amount of work in the irq handler, I took care of avoiding
any irq mask register operation in the slow work dedicated user
context thread. The slow work thread scheduled an extra round of NAPI
work which would ultimately set the irq mask register as required,
thus keeping such irq mask operations in the NAPI handler.
It would eventually race with the irq handler and delay NAPI execution
for - assuming no further irq - a whole ksoftirqd period. Mildly a
problem for rare link changes or corner case PCI events.
The race was always lost after the last bh disabling lock had been
removed from the work thread and people started wondering where those
pesky "NOHZ: local_softirq_pending 08" messages came from.
Actually the irq mask register _can_ be set up directly in the slow
work thread.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Marc Dionne <marc.c.dionne@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when register_netdev fails, the init'ed NAPIs by netif_napi_add must be
deleted with netif_napi_del, and also when driver unloads, it should
delete the NAPI before unregistering netdevice using unregister_netdev.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we terminate the eeprom access through clearing the CS by:
RTL_W8 (Cfg9346, ~EE_CS); or writeb (~EE_CS, ee_addr);
This would left the eeprom into "Config. Register Write Enable:"
state which is not expcted as the highest two bits were set to
0x11 ( expected is the "Normal" mode (0x00)). Solving this by write
0x0 instead of ~EE_CS when terminating the eeprom access.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we enable the receiver before setting the ring address which could
lead the card DMA into unexpected areas. Solving this by set the ring address
before enabling the receiver.
btw. I find and test this in qemu as I didn't have a 8139cp card in hand. please
review it carefully.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
The r8169 may get stuck or show bad behaviour after activating TSO :
the net_device is not stopped when it has no more TX descriptors.
This problem comes from TX_BUFS_AVAIL which may reach -1 when all
transmit descriptors are in use. The patch simply tries to keep positive
values.
Tested with 8111d(onboard) on a D510MO, and with 8111e(onboard) on a
Zotac 890GXITX.
Signed-off-by: Julien Ducourthial <jducourt@free.fr>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compared with previous chipsets, it needs no special action trough the
jumbo{enable/disable} helpers to operate with jumbo frames.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Adjust r810x_pll_power_down, r810x_pll_power_up, and r8168_pll_power_up.
Always power up device during rtl_open. For r810x, turn off more power
when the WOL is disabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Conflicts:
drivers/net/ethernet/atheros/atlx/atl1.c
drivers/net/ethernet/atheros/atlx/atl1.h
Resolved a conflict between a DMA error bug fix and NAPI
support changes in the atl1 driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
We set intr mask before its handler is registered, this does not work well when
8139cp is sharing irq line with other devices. As the irq could be enabled by
the device before 8139cp's hander is registered which may lead unhandled
irq. Fix this by introducing an helper cp_irq_enable() and call it after
request_irq().
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge with latest Linus' tree, as I have incoming patches
that fix code that is newer than current HEAD of for-next.
Conflicts:
drivers/net/ethernet/realtek/r8169.c
NAPI is disabled during suspend and needs to be enabled on resume. Without
this the driver locks up during resume in rtl_reset_work() trying to disable
NAPI again.
Signed-off-by: Artem Savkov <artem.savkov@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
The below patch fixes a typo that I found while reading the code.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch has been tested on a machine with the Realtek
RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05).
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not need this leftover of the ISA drivers era.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
With runtime PM, if the ethernet cable is disconnected, the device is
transitioned to D3 state to conserve energy. If the system is shutdown
in this state, any register accesses in rtl_shutdown are dropped on
the floor. As the device was programmed by .runtime_suspend() to wake
on link changes, it is thus brought back up as soon as the link recovers.
Resuming every suspended device through the driver core would slow things
down and it is not clear how many devices really need it now.
Original report and D0 transition patch by Sameer Nanda. Patch has been
changed to comply with advices by Rafael J. Wysocki and the PM folks.
Reported-by: Sameer Nanda <snanda@chromium.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to use ndo_get_stats64 to get 64bit statistics.
Two sync entries are used (one for Rx and one for Tx).
Signed-off-by: Junchang Wang <junchangwang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vmxnet3/vmxnet3_drv.c
Small vmxnet3 conflict with header size bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing fancy:
- sent bytes count is notified in the start_xmit path right before
updating the owner bit in the hardware Tx descriptor (E. Dumazet)
- avoid useless tp->dev dereferencing in start_xmit (E. Dumazet)
Use of netdev_reset_queue is favored over proper accounting in
rtl8169_tx_clear_range since the latter would need more work for the
same result (nb: said accounting degenerates to nothing in xmit_frags).
Signed-off-by: Igor Maravic <igorm@etf.rs>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Switch to use ndo_get_stats64 to get 64bit statistics.
Two sync entries are used (one for Rx and one for Tx).
Signed-off-by: Junchang Wang <junchangwang@gmail.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Noticed with the 8168d (-vb-gr, aka RTL_GIGA_MAC_VER_26).
ConfigX registers should only be written while the Config9346 lock
is held.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Nick Bowler <nbowler@elliptictech.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows the NIC to receive the Ethernet FCS
and pass it up the stack, allowing sniffers and
other interested programs to inspect the FCS.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This allows the NIC to receive packets with bad FCS and
Runts, which can help when sniffing.
NOTE: r8169, at least on my NIC, silently drops packets
with bad FCS instead of counting them. It seems they are
only received in any fashion if the RxCRC flag is set
(which this patch allows).
Signed-off-by: Ben Greear <greearb@candelatech.com>
This allows the NIC to pass the Ethernet FCS on up
the stack, and is useful when sniffing networks.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This allows the NIC to receive Runts and frames with bad
Ethernet Frame Checksums (FCS).
Useful to sniffing & diagnosing bad networks.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
- Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8169_get_regs operates under RTNL and rtl task mutex whereas
rtl_set_rx_mode is either called under RTNL or rtl task mutex protection.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Simpler, more consistent, with negligible cost in non-critical paths.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Suggested-by: Michał Mirosław <mirqus@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>
- atomic bit operations are globally visible
- pending status is always cleared before execution
- scheduled works are either idempotent or only required to happen once
after a series of originating events, say link events for instance
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Suggested-by: Michał Mirosław <mirqus@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>
With infinite gratitude to Eric Dumazet for allowing me to identify
the error.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>
The reorganization of the driver layout in drivers/net
left behind some stale paths in comments and in Kconfig
help text. Bring them up to date. No actual change to
any code takes place here.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The irq handler was a mess.
See 7ab87ff4c7 ("via-rhine: move work from
irq handler to softirq and beyond") for similar changes. One can notice:
- all non-napi tasks are explicitely scheduled trough a single work queue.
- hiding software tx queue start behind the rtl_hw_start method is mildly
natural. Move it in the caller where needed.
- as can be seen from the heavy use of bh disabling locks, the driver is
not safe for irq context messages with netconsole. It is still quite
usable for general messaging though. Tested ok with concurrent registers
dump (ethtool -d) + background traffic + "echo t > /proc/sysrq-trigger".
Tested with old PCI chipset, PCIe 8168 and 810x:
- XID 0c900800 RTL8168evl/8111evl
- XID 18000000 RTL8168b/8111b
- XID 98000000 RTL8169sc/8110sc
- XID 083000c0 RTL8168d/8111d
- XID 081000c0 RTL8168d/8111d
- XID 00b00000 RTL8105e
- XID 04a00000 RTL8102e
As a side note, the comments in f11a377b3f
("r8169: avoid losing MSI interrupts") does not seem completely clear: if
I hack the driver further to stop acking the irq link event bit, MSI
interrupts keep being delivered (RTL8168b/8111b, XID 18000000).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Though motivated by the move of the driver to a single work queue of
sequential events and removal of hard irq processing, it looks safe as
a standalone change.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
I see no good reason to keep both rtl8169_reinit_task and rtl8169_reset_task:
- rtl8169_reinit_task adds a software failure point which does relate to
any hardware state
- they handle hardware the same. Remember that rtl8169_reinit_task was
introduced in the 8169 only era to handle PCI errors way before the 8168
asked for pll and firmware ops and compare :
rtl8169_reinit_task | rtl8169_reset_task
----------------------------+--------------------------
rtl8169_wait_for_quiescence | rtl8169_hw_reset
rtl8169_update_counters | rtl8169_wait_for_quiescence
rtl8169_hw_reset | rtl_hw_start
rtl8169_rx_missed | rtl8169_check_link_status
rtl_pll_power_down |
rtl_request_firmware |
rtl8169_init_phy |
rtl_pll_power_up |
rtl_hw_start |
rtl8169_check_link_status |
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
The driver uses __napi_complete and napi_gro_receive. Without it, the
driver hits the BUG_ON(n->gro_list) assertion hard in __napi_complete.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Marin Glibic <zhilla2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx mode should be reset after resming, so unconditionally updating rx
mode rather than conditionally updating based on the value we
remembered, otherwise unexpected value may be used by the nic after
resuming.
btw. I find and test this when debugging guest hibernation in qemu, as
I did not have a 8139cp card in hand, this patch is untested in a
physical 8139cp card, plase review it carefully.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
delay_eeprom() use long read for Cfg9346 register(offset 0x50) which may read
into the area of reserved register(offset 0x53). Use byte read instead.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bluetooth/l2cap_core.c
Just two overlapping changes, one added an initialization of
a local variable, and another change added a new local variable.
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSIEnable bit is only available for the 8169.
Avoid Config2 writes for the post-8169 8168 and 810x.
Reported-by: Su Kang Yin <cantona@cantona.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 92fc43b415, rtl8169_tx_timeout ends up
resetting Rx and Tx indexes and thus racing with the NAPI handler via
-> rtl8169_hw_reset
-> rtl_hw_reset
-> rtl8169_init_ring_indexes
What about returning to the original state ?
rtl_hw_reset is only used by rtl8169_hw_reset and rtl8169_init_one.
The latter does not need rtl8169_init_ring_indexes because the indexes
still contain their original values from the newly allocated network
device private data area (i.e. 0).
rtl8169_hw_reset is used by:
1. rtl8169_down
Helper for rtl8169_close. rtl8169_open explicitely inits the indexes
anyway.
2. rtl8169_pcierr_interrupt
Indexes are set by rtl8169_reinit_task.
3. rtl8169_interrupt
rtl8169_hw_reset is needed when the device goes down. See 1.
4. rtl_shutdown
System shutdown handler. Indexes are irrelevant.
5. rtl8169_reset_task
Indexes must be set before rtl_hw_start is called.
6. rtl8169_tx_timeout
Indexes should not be set. This is the job of rtl8169_reset_task anyway.
The removal of rtl8169_hw_reset in rtl8169_tx_timeout and its move in
rtl8169_reset_task do not change the analysis.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: hayeswang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek has specified that the post 8168c gigabit chips and the post
8105e fast ethernet chips recover automatically from a Rx FIFO overflow.
The driver does not need to clear the RxFIFOOver bit of IntrStatus and
it should rather avoid messing it.
The implementation deserves some explanation:
1. events outside of the intr_event bit mask are now ignored. It enforces
a no-processing policy for the events that either should not be there
or should be ignored.
2. RxFIFOOver was already ignored in rtl_cfg_infos[RTL_CFG_1] for the
whole 8168 line of chips with two exceptions:
- RTL_GIGA_MAC_VER_22 since b5ba6d12bd
("use RxFIFO overflow workaround for 8168c chipset.").
This one should now be correctly handled.
- RTL_GIGA_MAC_VER_11 (8168b) which requires a different Rx FIFO
overflow processing.
Though it does not conform to Realtek suggestion above, the updated
driver includes no change for RTL_GIGA_MAC_VER_12 and RTL_GIGA_MAC_VER_17.
Both are 8168b. RTL_GIGA_MAC_VER_12 is common and a bit old so I'd rather
wait for experimental evidence that the change suggested by Realtek really
helps or does not hurt in unexpected ways.
Removed case statements in rtl8169_interrupt are only 8168 relevant.
3. RxFIFOOver is masked for post 8105e 810x chips, namely the sole 8105e
(RTL_GIGA_MAC_VER_30) itself.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: hayeswang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Round-up some wayward "N/A" fw_version dust bunnies as part of that
clean-up.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the number of #defines, use the normal #define from if_ether.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per the mention made by Ben Hutchings that strlcpy is now the preferred
string copy routine for a .get_drvinfo routine, do a bit of floor
sweeping and convert some of the as-yet unconverted ethernet drivers to
it.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link down would occur when reseting PHY. And it would take about 2 ~ 5 seconds
from link down to link up. If the delay of pm_schedule_suspend is not long enough,
the device would enter runtime_suspend before link up. After link up, the device
would wake up and reset PHY again. Then, you would find the driver keep in a loop
of runtime_suspend and rumtime_resume.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the SC92031 could be found on fake "Realtek" NICs, it has no
relationship to Realtek, and is actually from Silan.
Create a new subdirectory for silan and move sc92031 there.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reporting ring sizes via ethtool -g to the 8139cp driver.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix features : jumbo frames and checksumming can not be used at the
same time.
- introduce hw_jumbo_{enable / disable} helpers. Their content has been
creatively extracted from Realtek's own drivers. As an illustration,
it would be nice to know how/if the MaxTxPacketSize register operates
when the device can work with a 9k jumbo frame as its documentation
(8168c) can not be applied beyond ~7k.
- rtl_tx_performance_tweak is moved forward. No change.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
8168d and above allow jumbo frames beyond 8k. Bump the received
packet length check before enabling jumbo frames on these chipsets.
Frame length indication covers bits 0..13 of the first Rx descriptor
32 bits for the 8169 and 8168. I only have authoritative documentation
for the allowed use of the extra (13) bit with the 8169 and 8168c.
Realtek's drivers use the same mask for the 816x and the fast ethernet
only 810x.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
For RTL8111EVL, the register of MaxTxPacketSize doesn't acctually
limit the tx size. It influnces the feature of early tx.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
MII Kconfig option is apart of the core networking drivers and
by default NET_CORE is enabled so drivers selecting MII will
have MII enabled as well. It was found using the randconfig
option during testing, MII would be selected but NET_CORE
could be disabled. This caused a dependency error.
Resolved the dependency by selecting NET_CORE when MII is
selected.
Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on finds for Stephen Rothwell, where current defconfig's
enable a ethernet driver and it is not compiled due to the newly
added NET_VENDOR_* component of Kconfig.
This patch enables all the "new" Kconfig options so that current
defconfig's will continue to compile the expected drivers. In
addition, by enabling all the new Kconfig options does not add
any un-expected options.
CC: Stephen Rothwll <sfc@canb.auug.org.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Realtek drivers into drivers/net/ethernet/realtek/ and make
the necessary Kconfig and Makefile changes.
CC: Realtek linux nic maintainers <nic_swsd@realtek.com>
CC: Francois Romieu <romieu@fr.zoreil.com>
CC: Jeff Garzik <jgarzik@pobox.com>
CC: Donald Becker <becker@scyld.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
