Preparing to use the same mutex for disk_conf updates
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
An administrative detach used to request a state change directly to D_DISKLESS,
first suspending IO to avoid the last put_ldev() occuring from an endio handler,
potentially in irq context.
This is not enough on the receiving side (typically secondary), we may miss
some peer_req on the way to local disk, which then may do the last put_ldev()
from their drbd_peer_request_endio().
This patch makes the detach always go through the intermediate D_FAILED state.
We may consider to rename it D_DETACHING.
Alternative approach would be to create yet an other work item to be scheduled
on the worker, do the destructor work from there, and get the timing right.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
There are races where the receiver may be exiting,
but still need the worker to process some stuff.
Do not wait for the receiver to die from an exiting worker.
The receiver must already be dead in case the worker decides to exit.
If the receiver was still alive, it may still want to queue work, and do
drbd_flush_workqueue() from it's disconnect cleanup code,
which would no longer be processed by an exiting worker.
This also would deadlock,
if the worker was to synchornously wait for the receiver to die.
Do not implicitly stop the worker.
The worker will only be stopped from configuration context, from
conn_reconfig_done(), drbd_adm_down() or drbd_adm_delete_connection(),
after making sure the receiver is already stopped.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If a forced disconnect hits a restarting receiver right after it passed
its final "if (C_DISCONNECTING)" test in drbdd_init(), but before it was
actually restarted by drbd_thread_setup, we could be left with a
connection stuck in C_DISCONNECTING, never reaching C_STANDALONE,
which would be necessary to take it down or reconfigure it.
Move the last cleanup into w_after_conn_state_ch(), and do an additional
state change request in conn_try_disconnect(), just in case.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The main purpose of this is to allow to turn data integrity checking on
and off on demand without causing interruptions.
Implemented by allocating tconn->peer_integrity_tfm only when receiving
a P_PROTOCOL message. l accesses to tconn->peer_integrity_tf happen in
worker context, and no further synchronization is necessary.
On the sender side, tconn->integrity_tfm is modified under
tconn->data.mutex, and a P_PROTOCOL message is sent whenever. All
accesses to tconn->integrity_tfm already happen under this mutex.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We allocate hash transformations with crypto_alloc_hash() which will
only return hash algorithms. It is not necessary to reconfirm that we
actually got a hash algorithm.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
It is not enough to grab net_conf->integrity_alg under rcu_read_lock()
and access it outside of it; the entire net_conf object may be gone by
then.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
sc was short for syncer conf, which does not exist anymore anyways.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The DRBD_GENL_F_SET_DEFAULTS flag was ignored
for drbd_adm_disk_opts() and drbd_adm_net_opts().
Factor out drbd_set_*_defaults() helper functions,
and call them appropriately.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
So for this was simply not considered after the options have been
re-arranged.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If an admin requests disconnect at a time when the state handling
already disconnects/reconnects, there have been some races.
Make sure to always really stop the network threads before
returning success for disconnect. Do not pretend successfull
forced disconnect, if the state handling returned an error.
Return success from drbd_adm_down() only after all threads are finished.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Calling kobject_uevent, which may sleep, from within rcu_read_lock()
protected regions is not possible.
This particular kobject_uevent also is also wrong. It was supposed to
trigger a udev run, just in case something relevant to udev symlink
magic has changed, when adjusting runtime re-configurable settings while
we still had the "syncer conf". It was improperly placed in connect
when we dropped the "syncer conf". The right thing to do is probably to
call "udevadm trigger" directly in those cases where drbdadm thinks
there was a need to trigger extra udev runs.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
References hold by:
* Each (running) drbd thread has a reference on tconn
* Each mdev has a referenc on tconn
* Beeing in the all_tconn list counts for one reference
* Each after_conn_state_chg_work has a reference to tconn
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When the last volume of a replication group is unconfigured,
the worker thread exits. To not interfere with cleanup
of other threads, before the the last cleanups run,
we need to make sure the receiver has already exited.
The commend explaining that clearly belongs above
drbd_thread_stop(&tconn->receiver), not in the cleanup loop below.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We use our own copy of kernel_setsockopt, and did not mess around with
get_fs/set_fs, since we thought we knew we would always be KERNEL_DS
anyways. Apparently not so for at least user mode linux, so put the
set_fs(KERNEL_DS) in there.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We had drbd_adm_get_status (one single volume),
and drbd_adm_get_status_all (dump of all volumes of all resources).
This enhances the latter to be able to dump all volumes
of just one specific resource.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Now since it is possible to change the two_primaries config
flag while the connection is up, make sure we treat a peer_req
in a consistent way if the config flag changes while the peer_req
is under IO.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Removing the get_net_conf()/put_net_conf() functions
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Removing the get_net_conf()/put_net_conf() calls
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The wire protocol is no longer a property that is negotiated
between the two peers. It is now expressed with two bits
(DP_SEND_WRITE_ACK and DP_SEND_RECEIVE_ACK) in each data
packet. Therefore the primary node is free to change the
wire protocol at any time without disconnect/reconnect.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
With this commit the locking for all accesses to IDRs is complete:
* Non sleeping read accesses are protected by RCU
* sleeping read accesses are protocted by a read lock on drbd_cfg_rwsem
* accesses that add anything are protected by a write lock
* accesses that remove an object are protoected by a write lock
and a call to synchronize_rcu() after it is removed from the IDR
and before the object is actually free()ed.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Since have now header 100, that has space for 16 bit volume numbers,
the high byte of the length in header 95 is no longer reserved for
8 bit volume numbers.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The 8 byte header finally becomes too small. With the protocol 100 header we
have 16 bit for the volume number, proper 32 bit for the data length, and
32 bit for further extensions in the future.
Previous versions of drbd are using version 80 headers for all packets
short enough for protocol 80. They support both header versions in
worker context, but only version 80 headers in asynchronous context.
For backwards compatibility, continue to use version 80 headers for
short packets before protocol version 100.
From protocol version 100 on, use the same header version for all
packets.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Prepare the introduction of the protocol 100 headers. The actual protocol
header is removed for the packet declarations. I.e. allow us to use the
packets with different headers.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Centralize sock->mutex locking and unlocking in [drbd|conn]_prepare_command()
and [drbd|conn]_send_comman().
Therefore all *_send_* functions are touched to use these primitives instead
of drbd_get_data_sock()/drbd_put_data_sock() and former helper functions.
That change makes the *_send_* functions more standardized.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Recent commit drbd: get rid of bio_split, allow bios of "arbitrary" size
had a reference count leak: it only deactivated the first of several
activity log extents for intervals crossing extent boundaries.
This commit generalizes on bios spanning multiple activity log extents
in drbd_al_begin_io, and adds the necessary loop around lc_put in
drbd_al_complete_io as well.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Where "arbitrary" size is currently 1 MiB, which is the BIO_MAX_SIZE
for architectures with 4k PAGE_CACHE_SIZE (most).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We want to avoid bio_split for bios crossing activity log boundaries.
So we may need to activate two activity log extents "atomically".
drbd_al_begin_io() needs to know more than just the start sector.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
So we can initialize a clean on disk activity log area,
without the module complaining with loud assert messages
because of checksum or magic value mismatches.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Packets of type P_HAND_SHAKE define which protocol versions and features
a node supports. For clarity, call those packets P_CONNECTION_FEATURES
instead.
(This does not determine the features that a specific drbd device
supports, such as drbd protocol A, B, C.)
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The first packets exchanged when a connection is established are
referred to as P_HAND_SHAKE_S and P_HAND_SHAKE_M in the code, followed
by P_HAND_SHAKE packets. To avoid confusion between these two unrelated
things, call the initial packets P_INITIAL_DATA and P_INITIAL_META.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
During a disconnect the oc variable in _conn_request_state()
could become outdated. Determin the common old state after
sleeping.
While at it, I implemented that for all parts of the state
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The receive handlers do not all handle unknown volume numbers the same
way.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
These messages can only trigger in case there is a pretty obvious
internal programming error.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
There is no need to send protocol 80 headers to peers that understand
protocol 95 headers. Make sure that we don't send protocol 95 headers
until we have agreed upon a protocol version with our peer, though.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
