Resetting the chip to a default transfer mode after each transfer
doesn't provide any benefit. Therefore remove this call.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch supports 32bytes of buffer for DUAL and QUAD in QSPI by
Using Transmit/Receive Buffer Data Triggering Number.
In order to improve the DUAL and QUAD's performance of SPI
while transferring data in PIO mode, it sends/receives each 32bytes
data instead of each byte data as current situation.
Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
H3 has two SPI controllers. The size of the buffer is 64 * 8.
(8 bit transfer by 64 entry FIFO)
A31 has four controllers. The size of the buffer is 128 * 8.
(8 bit transfer by 128 entry FIFO)
Register maps are sharable, so sun6i SPI driver is reusable with
device configuration.
Use the variable, 'fifo_depth' instead of fixed value to support both SPI
controllers.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce additional output parameter in spi_imx_clkdiv_1()
function to return result frequency and set it to spi_bus_clk.
This fixes division by zero bug, which occurred in
spi_imx_calculate_timeout() function.
Signed-off-by: Robert Baldyga <r.baldyga@hackerion.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Once dspi is used in uboot, the SPI_SR have been set by some value.
At this time, if kernel enable the interrupt before clear the
status flag, that will trigger the wrong interrupt.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI transfers were limited to one FIFO depth, which is 64 bytes.
This was an artificial limitation, however, as the hardware can handle
much larger bursts. To accommodate this, we enable the interrupt when
the Rx FIFO is 3/4 full, and drain the FIFO within the interrupt
handler. The 3/4 ratio was chosen arbitrarily, with the intention to
reduce the potential number of interrupts.
Since the SUN4I_CTL_TP bit is set, the hardware will pause
transmission whenever the FIFO is full, so there is no risk of losing
data if we can't service the interrupt in time.
For the Tx side, enable and use the Tx FIFO 3/4 empty interrupt to
replenish the FIFO on large SPI bursts. This requires more care in
when the interrupt is left enabled, as this interrupt will continually
trigger when the FIFO is less than 1/4 full, even though we
acknowledge it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olliver Schinagl <o.schinagl@ultimaker.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to NXP ESPI datasheet, the SPI clock rate is:
spi_clk = System_Clock / ( 2 * DIV16 * ( 1 + PM ) )
Where System_Clock is the platform clock divided by 2,
DIV16 may be 1 or 16, and PM is a 4 bits integer (0 to 15).
Isolating PM on the expression, we get:
PM = (System_Clock / ( 2 * DIV16 * spi_clk ) ) - 1
Where System_Clock = mpc8xxx_spi->spibrg / 2, spi_clk = hz,
and DIV16 = 1 or DIV16 = 16. So,
PM = (mpc8xxx_spi->spibrg / ( 4 * hz) ) - 1
or
PM = (mpc8xxx_spi->spibrg / ( 16 * 4 * hz) ) - 1
Current spi-fsl-espi driver can't configure the HW for all
supported clock rates. It filters out clock rates for PM = 0
and PM = 1.
This patch allows all range of supported clock rates to be
configured on the ESPI controller.
Signed-off-by: Paulo Zaneti <paulo.zaneti@datacom.ind.br>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
spin_lock is used to obtain the spinlock, so spin_unlock
has to be used here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the driver polls in the ISR for enough bytes in the RX FIFO.
An ISR should never do this.
Change it to read as much as possible whenever the ISR is called.
This also allows to significantly simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
So far an interrupt is triggered whenever there's at least one byte
in the RX FIFO. This results in a unnecessarily high number of
interrupts.
Change this to generate an interrupt if
- RX FIFO is half full (except if all bytes to read fit into the
RX FIFO anyway)
- end of transfer has been reached
This way the number of interrupts can be significantly reduced.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend and improve transfer error handling
- in case of timeout report also number of remaining rx bytes
- in case of timeout return ETIMEDOUT instead of EMSGSIZE
- add sanity checks after all bytes have been sent / read:
- check that HW has flag SPIE_DON set
- check that RX / TX FIFO are empty
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ESPI spec mentions no requirement to turn off the ESPI unit prior
to changing the mode. Most likely the ESPI unit is only turned off to
clear the FIFO's as before this patch series single bytes could
remain in the TX FIFO after transfer end.
Therefore remove disabling / re-enabling the ESPI unit.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we introduced element tx_len in struct mpc8xxx_spi let's
rename element len to rx_len as it actually is the number of bytes to
receive. In addition make it unsigned.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change addresses two issues:
- If the TX FIFO is full the ISR polls until there's free space again.
An ISR should never wait for something.
- Currently the number of bytes to transfer is rounded up to the next
multiple of 4. For most transfers therefore few bytes remain in the
TX FIFO after end of transfer.
This would cause the next transfer to fail and as a workaround the
ESPI block is disabled / re-enabled in fsl_espi_change_mode.
This seems to clear the FIFO's (although it's not mentioned in the
spec).
With this change the TX FIFO is filled as much as possible initially
and whenever the ISR is called. Also the exact number of bytes is
transferred.
The spinlock protects against a potential race if the first interrupt
occurs whilst the TX FIFO is still being initially filled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI_QE_CPU_MODE doesn't exist for ESPI and is set by of_mpc8xxx_spi_probe
based on DT property "mode". This property is not defined for ESPI,
see Documentation/devicetree/bindings/spi/fsl-spi.txt.
So print an error message and bail out if SPI_QE_CPU_MODE is set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 5c0ba57744 ("spi: fsl-espi: avoid processing uninitalized
data on error") applied fine to stable but caused a merge conflict
on next. This patch fixes that.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_transfer parameter delay_usecs allows specifying a time to wait
after transferring a spi message. This wait can be quite long - some
devices, such as some Chrome OS ECs, require as much as 2000 usecs after
a SPI transaction, before it can respond.
(cf: arch/arm64/boot/dts/nvidia/tegra132-norrin.dts:
google,cros-ec-spi-msg-delay = <2000>
)
Blocking a CPU for 2 msecs in a busy loop like this doesn't seem very
friendly to other processes, so change the blocking delay to a sleep
to allow other things to use this CPU (or so it can sleep).
This should be safe to do, because:
(a) A post-transaction delay like this is always specified as a minimum
wait time
(b) A delay here is most likely not very time sensitive, as it occurs
after all data has been transferred
(c) This delay occurs in a non-critical section of the spi worker thread
so where it is safe to sleep.
Two caveats:
1) To avoid penalizing short delays, still use udelay for delays < 10us.
2) usleep_range() very often picks the upper bound, an upper bounds 10%
should be plenty.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we get a spurious interrupt in fsl_espi_irq, we end up
processing four uninitalized bytes of data, as shown in this
warning message:
drivers/spi/spi-fsl-espi.c: In function 'fsl_espi_irq':
drivers/spi/spi-fsl-espi.c:462:4: warning: 'rx_data' may be used uninitialized in this function [-Wmaybe-uninitialized]
This adds another check so we skip the data in this case.
Fixes: 6319a68011 ("spi/fsl-espi: avoid infinite loops on fsl_espi_cpu_irq()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Instantiated SPI device nodes are marked with OF_POPULATE. This was
introduced in bd6c164. On unloading, loaded device nodes will of course
be unmarked. The problem are nodes that fail during initialisation: If a
node fails, it won't be unloaded and hence not be unmarked.
If a SPI driver module is unloaded and reloaded, it will skip nodes that
failed before.
Skip device nodes that are already populated and mark them only in case
of success.
Note that the same issue exists for I2C.
Fixes: bd6c164 ("spi: Mark instantiated device nodes with OF_POPULATE")
Signed-off-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Support DMA transfers on imx35 and compatible chipsets (imx31, imx25).
If DMA can be used, set the start mode control (SMC) bit to start the
SPI burst as soon as data is written into the tx fifo. Configure DMA
requests when the fifo is half empty during tx or half full during rx.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Entries are needed in the spidev ID list to configure configure it from a
device tree. Add entry for the following device:
- "ge,achc" : GE Healthcare USB Management Controller
The USB Management Controller does not expose USB to the host, but acts as
an offload engine, communicating with specific USB based data acquisition
devices which are connected to it, extracting the required data and
providing it to the host via other methods. SPI is used as an out-of-band
configuration channel.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
currently during probe the resource data gets modified and device
physical address remains valid only during first load. If the module is
unloaded and loaded again, the ioremp will be done on a incorrect address
as the resource was modified during previous module load.
This patch fixes this issue.
Signed-off-by: Vikram N <vicky773@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code in fsl_espi_tx_buf_lsb and parts of fsl_espi_setup_transfer
look very weird and don't reflect the ESPI spec.
ESPI stores values with <= 8 bit word size right justified as 8 bit
value and values with > 8 bit word size right justified as 16 bit
value. Therefore no such shifting is needed.
Only case MSB-first with 8 bit word size is correctly handled,
and most likely nobody ever used this driver with a different config.
On ESPI only the case LSB-first with word size > 8 bit needs a
special handling. In this case a little endian 16 bit value has
to be written to the TX FIFO what requires a byte swap as the
host system is big endian.
The same applies to reading from the RX FIFO.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the ESPI spec MSB-first transfers are supported for
word size 8 and 16 only.
Check for this and reject MSB-first transfers with other word sizes.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_property_read_u32 is better here than generic of_get_property:
- implicit endianness conversion if needed
- implicit checking of size of property
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SPI masters require slave selection before the transfer
can begin [1]. The SPI framework currently selects the chip using
either 1) the internal CS mechanism or 2) the GPIO CS, but not both.
This patch adds a new master->flags define to indicate both the GPIO
CS and the internal chip select mechanism should be used.
Tested On:
Altera CycloneV development kit
Compile tested for build errors on x86_64 (allyesconfigs)
[1] DesignWare dw_apb_ssi Databook, Version 3.20a (page 39)
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A good practice is to prefix the names of functions by the name
of the subsystem.
The kthread worker API is a mix of classic kthreads and workqueues. Each
worker has a dedicated kthread. It runs a generic function that process
queued works. It is implemented as part of the kthread subsystem.
This patch renames the existing kthread worker API to use
the corresponding name from the workqueues API prefixed by
kthread_:
__init_kthread_worker() -> __kthread_init_worker()
init_kthread_worker() -> kthread_init_worker()
init_kthread_work() -> kthread_init_work()
insert_kthread_work() -> kthread_insert_work()
queue_kthread_work() -> kthread_queue_work()
flush_kthread_work() -> kthread_flush_work()
flush_kthread_worker() -> kthread_flush_worker()
Note that the names of DEFINE_KTHREAD_WORK*() macros stay
as they are. It is common that the "DEFINE_" prefix has
precedence over the subsystem names.
Note that INIT() macros and init() functions use different
naming scheme. There is no good solution. There are several
reasons for this solution:
+ "init" in the function names stands for the verb "initialize"
aka "initialize worker". While "INIT" in the macro names
stands for the noun "INITIALIZER" aka "worker initializer".
+ INIT() macros are used only in DEFINE() macros
+ init() functions are used close to the other kthread()
functions. It looks much better if all the functions
use the same scheme.
+ There will be also kthread_destroy_worker() that will
be used close to kthread_cancel_work(). It is related
to the init() function. Again it looks better if all
functions use the same naming scheme.
+ there are several precedents for such init() function
names, e.g. amd_iommu_init_device(), free_area_init_node(),
jump_label_init_type(), regmap_init_mmio_clk(),
+ It is not an argument but it was inconsistent even before.
[arnd@arndb.de: fix linux-next merge conflict]
Link: http://lkml.kernel.org/r/20160908135724.1311726-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/1470754545-17632-3-git-send-email-pmladek@suse.com
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Designware SPI master requires slave selection before the transfer
can begin [1].
This patch uses the new master flag to indicate both the GPIO CS and
the internal chip select should be used.
Tested On:
Altera CycloneV development kit
Compile tested for build errors on x86_64 (allyesconfigs)
[1] DesignWare dw_apb_ssi Databook, Version 3.20a (page 39)
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SPI masters require slave selection before the transfer
can begin [1]. The SPI framework currently selects the chip using
either 1) the internal CS mechanism or 2) the GPIO CS, but not both.
This patch adds a new master->flags define to indicate both the GPIO
CS and the internal chip select mechanism should be used.
Tested On:
Altera CycloneV development kit
Compile tested for build errors on x86_64 (allyesconfigs)
[1] DesignWare dw_apb_ssi Databook, Version 3.20a (page 39)
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To avoid warning when using i2c gpio expander change call to the
cansleep variant. There should be no issue with sleeping in the
drivers probe function.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kbuild test robot reports:
drivers/spi/spi-pxa2xx.c: In function ‘setup_cs’:
drivers/spi/spi-pxa2xx.c:1190:20: error: implicit declaration of function ‘desc_to_gpio’
...
Reason for this is the fact that those functions are declared in
linux/gpio/consumer.h which is not included in the driver. Fix this by
including it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix to return error code -EINVAL if no CS GPIOs available
instead of 0, as done elsewhere in this function.
Fixes: f13d4e189d ("spi: imx: Gracefully handle NULL master->cs_gpios")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver uses custom chip_info coming from platform data for chip selects
implemented as GPIOs. If the system lacks board files setting up the
platform data, it is not possible to use GPIOs as chip selects.
This adds support for GPIO descriptors so that regardless of the underlying
firmware interface (DT, ACPI or platform data) the driver can request GPIOs
used as chip selects and configure them accordingly.
The custom chip_info GPIO support is still left there to make sure the
existing systems keep working as expected.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is possible that master->cs_gpios is NULL after spi_bitbang_start(),
this happens if the master has no CS GPIOs specified in DT. Check for
this case after spi_bitbang_start() to prevent NULL pointer dereference
in the subsequent for loop, which accesses the master->cs_gpios field.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Martin Kaiser <martin@kaiser.cx>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This spi driver uses the common spi-bcm-qspi driver and implements iProc
SoCs specific interrupt controller. The common driver now calls the SoC
handlers when present. Adding support for both muxed l1 and unmuxed interrupt
sources.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The return value of fsl_espi_probe (currently struct spi_master *)
is just used for checking whether an error occurred.
Change the return value type to int and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of error, the function kcalloc() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The two power management functions are define inside of an #ifdef
but referenced unconditionally, which is obviously broken when
CONFIG_PM_SLEEP is not set:
drivers/spi/spi-bcm-qspi.c:1300:13: error: 'bcm_qspi_suspend' undeclared here (not in a function)
drivers/spi/spi-bcm-qspi.c:1301:13: error: 'bcm_qspi_resume' undeclared here (not in a function)
This replaces the #ifdef with a __maybe_unused annotation that lets
the compiler figure out whether to drop the functions itself,
and uses SIMPLE_DEV_PM_OPS() to refer to the functions.
This will also fill the freeze/thaw/poweroff/restore callback
pointers in addition to suspend/resume, but as far as I can tell,
this is what we want.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Mark Brown <broonie@kernel.org>
The header isn't actually needed here, but including it leads
to a build warning when CONFIG_MTD is disabled:
include/linux/mtd/cfi.h:76:2: #warning No CONFIG_MTD_CFI_Ix selected. No NOR chip support can work. [-Werror=cpp]
Fixes: fa236a7ef2 (spi: bcm-qspi: Add Broadcom MSPI driver)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add definition of further register bits for use in upcoming
driver extensions and improve current bit definitions:
- use BIT macro
- use bit names as in the chip spec
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change register access to the method used in other drivers too.
- use register names as in the chip spec for constants
- avoid hard to read statements like
__be32 __iomem *espi_mode = ®_base->mode
- get rid of old powerpc-specific functions like in_8
In addition annotate reg_base in struct mpc8xxx_spi as __iomem.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the interrupt handler a little. In addition don't call
fsl_espi_cpu_irq() if no event bit is set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If t is not null then the SPI core takes care that bits_per_word and
speed_hz are populated. This allows to simplify fsl_espi_setup_transfer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
imx35 and compatible chipsets support loopback mode by setting a
loopback control bit in the test register. Make this setting available
for data transfers, similar to what we do for imx51.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify spi_imx_clkdiv_2() to return the resulting bus clock frequency
when the selected clock divider is applied. Set spi_imx->spi_bus_clk to
this frequency.
If spi_bus_clk is unset, spi_imx_calculate_timeout() causes a
division by 0.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change implements BSPI driver for Broadcom BRCMSTB, NS2,
NSP SoCs works in combination with the MSPI controller driver
and implements flash read acceleration and implements the
spi_flash_read() method. Both MSPI and BSPI controllers are
needed to access spi-nor flash.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding the settop SoC platfrom driver, this driver is compatible
with the settop MSPI+BSPI and MSPI only blocks implemented on the
SoCs. Driver calls the spi-bcm-qspi probe(), remove() and pm_ops.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Master SPI driver for Broadcom settop, iProc SoCs. The driver
is used for devices that use SPI protocol on BRCMSTB, NSP, NS2
SoCs. SoC platform driver call exported porbe(), remove()
and suspend/resume pm_ops implemented in this common driver.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Yendapally Reddy Dhananjaya Reddy
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_* API is supposed to be used only in probe function call.
The resource is allocated at 'probe' and free automatically at 'remove'.
Usage of devm_* functions outside probe sometimes leads to resource leak.
Thus avoid using devm_* APIs in .setup/.cleanup callbacks.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge both functions to reduce source code size and improve
readability.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move checking for a zero-length message up in the call chain and
use m->frame_length instead of re-calculating the overall length
of all transfers in the message.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Factor out copying read data to the read buffers in the original
message to a new function fsl_espi_copy_from_buf.
This also allows to simplify fsl_espi_copy_to_buf.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Better structure the code by population all elements of struct
spi_transfer in one place.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Checking the message is currently done at diffrent places in the
driver. Factor it out to fsl_espi_check_message.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most of the devices in the supported list have PXA configuration of FIFO. In
particularly Intel Medfield and Merrifield have bigger FIFO, than it's defined
for CE4100.
Split CE4100 in the similar way how it was done for Intel Quark, i.e. prefix
definitions by CE4100 and append necessary pieces of code to switch case
conditions.
We are on safe side since those bits are ignored on all LPSS IPs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Transfer state machine in this driver does not need to set/unset pointer
to chip data between queueing and finalizing message as it is not
actually used as a state info itself but just pointer passing.
Since this per SPI device specific chip data is already carried in
ctldata use that and remove pointer to chip data from driver data.
While at it, group initialized variables before uninitialized variables
in pump_transfers().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to carry pointer to current SPI message in driver data
because cur_msg in struct spi_master holds it already when driver is using
the message queueing infrastructure from the SPI core.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All of these variables are unconditionally set before their use.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Avoid ending up with a higher frequency than requested
Signed-off-by: Matthias Seidel <kernel@mseidel.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
fsl_espi_bufs and fsl_espi_cpu_bufs are very small that we can merge them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return a proper status code from fsl_espi_bufs instead of returning
the number of remaining words and let the caller evaluate it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
fsl_espi_cmd_trans and fsl_espi_rw_trans share most of the code so
we can merge them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The remaining elements of struct fsl_espi_transfer are part of struct
spi_transfer anyway. So we can get rid of struct fsl_espi_transfer
and use a struct spi_transfer only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If an error occurs during processing the message, then we don't have
to populate the actual_length element of struct message.
So we can get rid of element actual_length in struct
fsl_espi_transfer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If an error occurred during message handling return this error instead
of always returning 0 and align the code with the generic
implementation in spi_transfer_one_message.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the return values of the functions in the call chain to transport
status information instead of using an element in struct
fsl_espi_transfer for this.
This is more in line with the general approach how to handle status
information and is one step further to eventually get rid of
struct fsl_espi_transfer completely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Better structure the code by factoring out filling the local buffer.
In addition don't initialize the complete local buffer at the
beginning of fsl_espi_do_one_msg. Instead move initialization of
those parts of the local buffer to be used for transfers w/o tx_buf
to fsl_espi_copy_to_buf.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the driver allocates a 64kb buffer for each single message.
On systems with little and fragmented memory this can result in
memory allocation errors. Solve this by pre-allocating a buffer.
This patch was developed in OpenWRT long ago, however it never
made it upstream.
I slightly modified the original patch to re-initialize the buffer
at the beginning of each transfer.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core takes care that both values are always populated.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add current master clock to dws struct and compare it against the
requestedtransfer speed. Update clock divider only if necessary.
Signed-off-by: Matthias Seidel <kernel@mseidel.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
When reading SPI flash as MTD device, the transfer length is
directly passed to the spi driver. If the requested data size
exceeds 512KB, it will cause the time out calculation to
overflow since transfer length is 32-bit unsigned integer.
This issue is resolved by using 64-bit unsigned integer
to perform the arithmetic.
Signed-off-by: Sien Wu <sien.wu@ni.com>
Acked-by: Brad Keryan <brad.keryan@ni.com>
Acked-by: Gratian Crisan <gratian.crisan@ni.com>
Acked-by: Brad Mouring <brad.mouring@ni.com>
Natinst-ReviewBoard-ID 150232
Signed-off-by: Mark Brown <broonie@kernel.org>
If the spi device is already runtime suspended, if spi_qup_suspend is
executed during suspend-to-idle or suspend-to-ram it will result in the
a splat from unpreparing a non-prepared clock.
This patch fixes the issue by executing clk_disable_unprepare conditionally
in spi_qup_suspend.
[Reworded commit message to remove irrelevant backtrace -- broonie]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Creating a message, adding one transfer, and then iterating over
all transfers in the message doesn't make sense.
We can simply use the original transfer directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing static declaration to fsl_espi_cpu_irq.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
fsl_espi_cpu_bufs always returns 0, so change the return type to void.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
fsl_espi_setup_transfer always returns 0, so change the return type
to void.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
irq.h isn't needed and it even shouldn't be included, see comment
at the beginning of this header file.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We get 1 warning when building kernel with W=1:
drivers/spi/spi-loopback-test.c:408:5: warning: no previous prototype for 'rx_ranges_cmp' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
So this patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"spi_sh_msiof" is used on sh7723 and sh7724 only. As all of the above
select ARCH_SHMOBILE, restrict its driver dependencies from SUPERH to
ARCH_SHMOBILE.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
This sc18is602 has a reset pin that may need to be deasserted.
Add optional binding to specifiy the reset pin via a gpio and deassert
during probe.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the missing clk_disable_unprepare() before return in the probe
error handling case and remove.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Slave devices are not enumerated by ACPI data because the ACPI handle for the
core driver is NULL if it was enumerated by PCI.
Propagate firmware node handle of the PCI device to the platform device.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The call sequence spi_alloc_master/spi_register_master/spi_unregister_master
is complete; it reduces the device reference count to zero, which and results
in device memory being freed. The subsequent call to spi_master_put is
unnecessary and results in an access to free memory. Drop it.
Fixes: 9298bc7273 ("spi: spi-fsl-dspi: Remove spi-bitbang")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_prepare_enable() may fail, so we should better check its
return value and propagate it in the case of failure.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add ThunderX SPI driver using the shared part from the Octeon
driver. The main difference of the ThunderX driver is that it
is a PCI device so probing is different. The system clock settings
can be specified in device tree.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While the custom minimal TXx9 clock implementation doesn't need or use
clock (un)prepare calls (they are dummies if !CONFIG_HAVE_CLK_PREPARE),
they are mandatory when using the Common Clock Framework.
Hence add them, to prepare for the advent of CCF.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The fsl-espi driver contains a read loop that implicitely assumes that
the device to read from is a m25p80 SPI NOR flash (bytes 2 - 4 of the
first write transfer are interpreted as 3 byte flash address).
Now that we have such a read loop in the spi-nor driver and are able
to correctly indicate the message size limit of the controller,
the read loop can be removed from the fsl-espi driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use mem-to-mem DMA to read from flash when reading in mmap mode. This
gives improved read performance and reduces CPU load.
With this patch the raw-read throughput is ~16MB/s on DRA74 EVM. And CPU
load is <20%. UBIFS read throughput ~13 MB/s.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
JFFS2 FS might sometime provide kmap'd buffers as destination
buffers to read data from flash. Update spi_map_buf() function to
generate sg_list for such buffers, so that SPI controllers drivers can
use DMA to read data into such buffers.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
For fixing this problem, we use of_device_get_match_data(), this will
simplify the code a little by using a standard function for
getting the match data.
Reported-by: coverity (CID 1324129)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_id->data is const, so instead of casting the pointer to drop its
const status, this patch constify the devtype_data pointer.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of error paths were missing drops of io_mutex.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add ACPI support for SPI controller on Broadcom Vulcan ARM64.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When you leave the clock divider at 0, 130kHz is the lowest you can go.
Also, by adjusting the clock divider you can get more accurate resolutions
for clock speeds lower than 16MHz. This patch uses the clock divider as
part of the bit rate setup.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using list_move_tail() and list_move() to simplify the code.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The J-Core "spi2" device is a PIO-based SPI master controller. It
differs from "bitbang" devices in that that it's clocked in hardware
rather than via soft clock modulation over gpio, and performs
byte-at-a-time transfers between the cpu and SPI controller.
This driver will be extended to support future versions of the J-Core
SPI controller with DMA transfers when they become available.
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The conversion from a look-up table to a calculation for clock generator
parameters forgot to take into account that BRDV x 1/1 is valid only if
BRPS is x 1/1 or x 1/2, leading to undefined behavior (e.g. arbitrary
clock rates).
This limitation is documented for the MSIOF module in all supported
SH/R-Mobile and R-Car Gen2/Gen3 ARM SoCs.
Tested on r8a7791/koelsch and r8a7795/salvator-x.
Fixes: 65d5665bb2 ("spi: sh-msiof: Update calculation of frequency dividing")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Device tree contents continue to be the largest branches we submit. This
time around, some of the contents worth pointing out is:
- New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large delta due
to indentation changes
- A new Tegra K1 board: Apalis
- A bunch of small updates to many Allwinner platforms; new hardware support,
some cleanup, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C4NU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Device tree contents continue to be the largest branches we submit.
This time around, some of the contents worth pointing out is:
New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large
delta due to indentation changes
- a new Tegra K1 board: Apalis
- a bunch of small updates to many Allwinner platforms; new hardware
support, some cleanup, etc"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (426 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: at91: Don't build unnecessary dtbs
ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
ARM: dts: at91: move isi definition to at91sam9g25ek
ARM: dts: at91: fix i2c-gpio node name
ARM: dts: at91: vinco: fix regulator name
ARM: dts: at91: ariag25 : fix onewire node
...
Quite a lot of cleanup and maintainence work going on this release in
various drivers, and also a fix for a nasty locking issue in the core:
- A fix for locking issues when external drivers explicitly locked the
bus with spi_bus_lock() - we were using the same lock to both control
access to the physical bus in multi-threaded I/O operations and
exclude multiple callers. Confusion between these two caused us to
have scenarios where we were dropping locks. These are fixed by
splitting into two separate locks like should have been done
originally, making everything much clearer and correct.
- Support for DMA in spi_flash_read().
- Support for instantiating spidev on ACPI systems, including some test
devices used in Windows validation.
- Use of the core DMA mapping functionality in the McSPI driver.
- Start of support for ThunderX SPI controllers, involving a very big
set of changes to the Cavium driver.
- Support for Braswell, Exynos 5433, Kaby Lake, Merrifield, RK3036,
RK3228, RK3368 controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXmPFBAAoJECTWi3JdVIfQbisH/355nT/cyqc08l9iC+a1zRDw
/Bf5kN8pqmu6+y3sMjAIdptZQTlXhgR4q1ZH+oNSfowCVgvJYWF6RVCEXDBh6XHs
YBQAFlYeSOO5cLTPQSDnn06oFucV/HZJppC6hM0SNclbVboeMBBS6S6aljXqMbj+
mFvtq6/iEsG6kgQcmcl3fm/SMOYF2OFDJyr66NimBXQGzjx84xJcG0eGk8kCIwEw
xyiE/WmB9WT2scFSgAsfaOEE27ozaq9iANNUA/ceUibQgQYpQveBgy4XVXFjEzFo
3BVvPYGGzjebzaXbMwDV6OvSgMwnTsMxjtZGsraxIEOcMdeeMEpn1/Ze4ksWi4c=
=R4Zx
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of cleanup and maintainence work going on this release in
various drivers, and also a fix for a nasty locking issue in the core:
- A fix for locking issues when external drivers explicitly locked
the bus with spi_bus_lock() - we were using the same lock to both
control access to the physical bus in multi-threaded I/O operations
and exclude multiple callers.
Confusion between these two caused us to have scenarios where we
were dropping locks. These are fixed by splitting into two
separate locks like should have been done originally, making
everything much clearer and correct.
- Support for DMA in spi_flash_read().
- Support for instantiating spidev on ACPI systems, including some
test devices used in Windows validation.
- Use of the core DMA mapping functionality in the McSPI driver.
- Start of support for ThunderX SPI controllers, involving a very big
set of changes to the Cavium driver.
- Support for Braswell, Exynos 5433, Kaby Lake, Merrifield, RK3036,
RK3228, RK3368 controllers"
* tag 'spi-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (64 commits)
spi: Split bus and I/O locking
spi: octeon: Split driver into Octeon specific and common parts
spi: octeon: Move include file from arch/mips to drivers/spi
spi: octeon: Put register offsets into a struct
spi: octeon: Store system clock freqency in struct octeon_spi
spi: octeon: Convert driver to use readq()/writeq() functions
spi: pic32-sqi: fixup wait_for_completion_timeout return handling
spi: pic32: fixup wait_for_completion_timeout return handling
spi: rockchip: limit transfers to (64K - 1) bytes
spi: xilinx: Return IRQ_NONE if no interrupts were detected
spi: xilinx: Handle errors from platform_get_irq()
spi: s3c64xx: restore removed comments
spi: s3c64xx: add Exynos5433 compatible for ioclk handling
spi: s3c64xx: use error code from clk_prepare_enable()
spi: s3c64xx: rename goto labels to meaningful names
spi: s3c64xx: document the clocks and the clock-name property
spi: s3c64xx: add exynos5433 spi compatible
spi: s3c64xx: fix reference leak to master in s3c64xx_spi_remove()
spi: spi-sh: Remove deprecated create_singlethread_workqueue
spi: spi-topcliff-pch: Remove deprecated create_singlethread_workqueue
...
The call to spi_master_put() in img_spfi_remove() is redundant since
the master is registered using devm_spi_register_master() and no
reference hold by using spi_master_get() in img_spfi_remove().
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The call to spi_master_put() in mtk_spi_remove() is redundant since
the master is registered using devm_spi_register_master() and no
reference hold by using spi_master_get() in mtk_spi_remove().
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The call to spi_master_put() in spi_qup_remove() is redundant since
the master is registered using devm_spi_register_master() and no
reference hold by using spi_master_get() in spi_qup_remove().
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
* acpi-tables:
ACPI: Rename configfs.c to acpi_configfs.c to prevent link error
ACPI: add support for loading SSDTs via configfs
ACPI: add support for configfs
efi / ACPI: load SSTDs from EFI variables
spi / ACPI: add support for ACPI reconfigure notifications
i2c / ACPI: add support for ACPI reconfigure notifications
ACPI: add support for ACPI reconfiguration notifiers
ACPI / scan: fix enumeration (visited) flags for bus rescans
ACPI / documentation: add SSDT overlays documentation
ACPI: ARM64: support for ACPI_TABLE_UPGRADE
ACPI / tables: introduce ARCH_HAS_ACPI_TABLE_UPGRADE
ACPI / tables: move arch-specific symbol to asm/acpi.h
ACPI / tables: table upgrade: refactor function definitions
ACPI / tables: table upgrade: use cacheable map for tables
Conflicts:
arch/arm64/include/asm/acpi.h
The current SPI code attempts to use bus_lock_mutex for two purposes. One
is to implement spi_bus_lock() which grants exclusive access to the bus.
The other is to serialize access to the physical hardware. This duplicate
purpose causes confusion which leads to cases where access is not locked
when a caller holds the bus lock mutex. Fix this by splitting out the I/O
functionality into a new io_mutex.
This means taking both mutexes in the DMA path, replacing the existing
mutex with the new I/O one in the message pump (the mutex now always
being taken in the message pump) and taking the bus lock mutex in
spi_sync(), allowing __spi_sync() to have no mutex handling.
While we're at it hoist the mutex further up the message pump before we
power up the device so that all power up/down of the block is covered by
it and there are no races with in-line pumping of messages.
Reported-by: Rich Felker <dalias@libc.org>
Tested-by: Rich Felker <dalias@libc.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Separate driver probing from SPI transfer functions.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Steven J. Hill <steven.hill@cavium.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the register definitions to the drivers directory because they
are only used there.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Steven J. Hill <steven.hill@cavium.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of hard-coding the register offsets put them into a struct
and set them in the probe function.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Steven J. Hill <steven.hill@cavium.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Storing the system clock frequency in struct octeon_spi avoids
calling the MIPS specific octeon_get_io_clock_rate() for every transfer.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Steven J. Hill <steven.hill@cavium.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove all calls to cvmx_read_csr()/cvmx_write_csr() and use
the portable readq()/writeq() functions.
Signed-off-by: Steven J. Hill <steven.hill@cavium.com>
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wait_for_completion_timeout returns unsigned long not int so the check for
<= 0 should be == 0 here, and the type unsigned long. The function return
is set to -ETIMEDOUT to reflect the actual problem.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
wait_for_completion_timeout returns unsigned long not int so the check for
<= 0 should be == 0 here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Rockchip SPI controller's length register only supports 16-bits,
yielding a maximum length of 64KiB (the CTRLR1 register holds "length -
1"). Trying to transfer more than that (e.g., with a large SPI flash
read) will cause the driver to hang.
Now, it seems that while theoretically we should be able to program
CTRLR1 with 0xffff, and get a 64KiB transfer, but that also seems to
cause the core to choke, so stick with a maximum of 64K - 1 bytes --
i.e., 0xffff.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return IRQ_NONE from the interrupt handler if the handler is running, but
no interrupt was detected. This allows the system to recover in case of an
interrupt storm due to an invalid interrupt configuration or faulty
hardware.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Xilinx SPI driver can operate without an IRQ, but not every error
returned by platform_get_irq() means that no IRQ was specified. It will
also return an error if the IRQ specification is invalid or the IRQ
provider is not yet available (EPROBE_DEFER).
So instead of ignoring all errors only ignore ENXIO, which means no IRQ was
specified, and propagate all other errors to device driver core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Patch a9e93e8 has erroneously removed some comments which are
important to understand why the bus frequency is multiplied by
two during the spi transfer.
Reword the previous comment to a more appropriate message.
Suggested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The new compatible is related to the Samsung Exynos5433 SoC. The
difference between the previous is that in the exynos5433 the SPI
controller is driven by three clocks instead of only one.
The new clock (ioclk) is controlling the input/output clock
whenever the controller is slave or master.
The presence of the clock line is detected from the compatibility
structure (exynos5433_spi_port_config) as a boolean value.
The probe function checks whether the ioclk is present and if so,
it acquires.
The runtime suspend and resume functions will handle the clock
enabling and disabling as well.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If clk_prepare_enable() fails do not return -EBUSY but use the
value provided by the function itself.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The goto labels of the style of
err4:
err3:
err2:
err1:
are complex to insert in between new errors without renaming all
the goto statements. Replace the errX naming style to meaningful
names in order to make it easier to insert new goto exit points.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Once a spi_master_get() call succeeds, we need an additional
spi_master_put() call to free the memory, otherwise we will
leak a reference to master. Fix by removing the unnecessary
spi_master_get() call.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to the newly upstreamed 'critical clocks' API we can now
safely handle clocking in the SPI and I2C drivers without fear
of catastrophically crippling the running platform.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The workqueue has a single workitem(&ss->ws) and hence doesn't require
ordering. Also, it is not being used on a memory reclaim path. Hence, the
singlethreaded workqueue has been replaced with the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in spi_sh_remove() to ensure that
there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The workqueue "wk" serves as a queue for carrying out execution
of requests. It has a single work item(&drv_data->work) and hence doesn't
require ordering. Also, it is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in pch_spi_free_resources() to ensure that
there are no pending tasks while disconnecting the driver.
Also dropped the label 'err_return' since it's not being used anymore.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds supports for SPI device enumeration and removal via
ACPI reconfiguration notifications that are send as a result of an
ACPI table load or unload operation.
The code is very similar with the device tree reconfiguration code
with only small differences in the way we test and set the enumerated
state of the device:
* the equivalent of device tree's OF_POPULATED flag is the
flags.visited field in the ACPI device and the following wrappers
are used to manipulate it: acpi_device_enumerated(),
acpi_device_set_enumerated() and acpi_device_clear_enumerated()
* the device tree code checks of status of the OF_POPULATED flag to
avoid trying to create duplicate Linux devices in two places: once
when the controller is probed, and once when the reconfigure event
is received; in the ACPI code the check is performed only once when
the ACPI namespace is searched because this code path is invoked in
both of the two mentioned cases
The rest of the enumeration handling is similar with device tree: when
the Linux device is unregistered the ACPI device is marked as not
enumerated; also, when a device remove notification is received we
check that the device is in the enumerated state before continuing
with the removal of the Linux device.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, the driver handles mapping buffers to be used by the DMA.
However, there are times that the current mapping implementation will
fail for certain buffers. Fortunately, the SPI framework can detect
and map buffers so its usable by the DMA.
Update the driver to utilize the SPI framework for buffer
mapping instead. Also incorporate hooks that the framework uses to
determine if the DMA can or can not be used.
This will result in the original omap2_mcspi_transfer_one function being
deleted and omap2_mcspi_work_one being renamed to
omap2_mcspi_transfer_one. Previously transfer_one was only responsible
for mapping and work_one handled the transfer. But now only transferring
needs to be handled by the driver.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function sg_split will be used by spi-omap2-mcspi to handle a SoC
workaround in the SPI driver. Therefore, select SG_SPLIT so this function
is available to the driver.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit 30f3a6ab44 ("spi: pxa2xx: Add support for both chip selects on
Intel Braswell") introduces a support of chipselects for Intel Braswell SPI
host controller. Though it missed to convert the PCI part of the driver.
Do conversion here which enables both chipselects on Intel Braswell when
enumerated via PCI.
We don't care about num_chipselect value since it is overrided inside core
driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It seems the commit e5262d0568 ("spi: spi-pxa2xx: SPI support for Intel Quark
X1000") misses one place to be adapted for Intel Quark, i.e. in reset_sccr1().
Clear all RFT bits when call reset_sccr1() on Intel Quark.
Fixes: e5262d0568 ("spi: spi-pxa2xx: SPI support for Intel Quark X1000")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This is a complex patch for refactoring CLPS711X SPI driver.
This change adds devicetree support and removes board support.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the clock is coming from the cmu it is not required to be
disabled and then re-enabled in order to change the rate.
Besides, some exynos chipsets (e.g. exynos5433) do not deliver
any to the SFR if one from the pclk ("spi" in this case) or sclk
("busclk") is disabled.
Remove the clock disabling/enabling to avoid falling into this
situation.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OMAP35x and OMAP37x mentions in the McSPI End-of-Transfer Sequences section
that if the McSPI is configured as a Master and only DMA RX is being
performed then the DMA transfer size needs to be reduced by 1 or 2.
This was originally implemented by:
commit 57c5c28dbc ("spi: omap2_mcspi rxdma bugfix")
This patch adds comments to clarify what is going on in the code since its
not obvious what problem its addressing.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some IoT and maker software stacks are using spidev to perform raw access
to the SPI bus instead of relying existing drivers provided by the kernel.
They then implement their own "drivers" in userspace on top of the spidev
raw interface. This is far from being an ideal solution but we do not want
to prevent using mainline Linux in these devices.
Now, it turns out that Windows has similar SPI devices than spidev which
allow raw access on the SPI bus to userspace programs as described in the
link below:
https://msdn.microsoft.com/windows/hardware/drivers/spb/spi-tests-in-mitt
These SPI test devices are also meant to be used during development and
testing.
In order to allow usage of spidev for development and testing in Linux, add
those same ACPI IDs to the spidev driver (which is Linux counterpart of the
Windows SPI test devices), but complain loudly so that users know it is not
good idea to use it in production systems. Instead they should be using
proper drivers for peripherals connected to the SPI bus.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simply sort header block alphabetically.
While here, sort devices by PCI ID and add a copyright line for Intel.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
pcim_iomap_table() can't fail when called after pcim_iomap_regions(). Moreover,
we already dereference returned value and kernel will crash if it is not
correct.
Remove obvious leftover of commit 0202775bc3 ("spi/pxa2xx-pci: switch to use
pcim_* interfaces").
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI controllers used on Intel Merrifield are PXA2XX compatible. This patch
enables them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move LPSS specific setup to a separate function. It makes ->probe() cleaner as
well as allows extend the driver for different variation of hardware in the
future, e.g. for Intel Merrifield.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kaby Lake PCH-H has the same SPI host controller as Skylake. Add these new
PCI IDs to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It generates a static checker warning if an if statement isn't indented.
I think the code is fine except for the white space issue.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The workqueue "workqueue" serves as a driver message queue.
It has a single work item(&drv_data->pump_messages) and hence doesn't
require ordering. Also, it is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in bfin_sport_spi_destroy_queue() to ensure
that there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The workqueue "workqueue" has a single work item(&mps->work)
doesn't require ordering. Also, it is not being used on a memory reclaim
path. Hence, the singlethreaded workqueue has been replaced with the use
of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in mpc52xx_psc_spi_of_remove() to ensure that
nothing is pending while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The workqueue "workqueue" has a single work item(&c->work) and hence
doesn't require ordering. Also, it is not being used on a memory reclaim
path. Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in txx9spi_remove() to ensure that
nothing is pending while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The workqueue "workqueue" serves as a driver message queue.
It has a single work item(&drv_data->pump_messages) and hence doesn't
require ordering. Also, it is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in bfin_spi_destroy_queue() to ensure that there
are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The whole function is inside an 'if' statement
("!is_polling(sdd)").
Check the opposite of that statement at the beginning and exit,
this way we can have one level less of indentation.
Remove the goto paths as they are redundant.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
At the start of the transfer, the spi_config function is called
twice, the first time when the 3c64xx_spi_prepare_message is
called and the second time with the s3c64xx_spi_transfer_one,
both called from the spi framework.
Remove the first call at the prepare message because in that
point we don't have the imformation about "bit per word" and
frequency.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the CS line is not connected, it is not needed to enable or
disable the chip selection functionality from the s3c64xx
devices in order to perform a transfer.
Set the CS controller logically always enabled already during
initialization (by writing '0' in the S3C64XX_SPI_SLAVE_SEL
register) and never disable it.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To enable/disable the CS line, the driver performs a writel in
the S3C64XX_SPI_SLAVE_SEL registers. Group the register's
configuration in a single function.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The speed limits are unset in the sun4i and sun6i SPI drivers.
The maximum speed of SPI master is used when maximum speed of SPI slave
is not specified. Also the __spi_validate function should check that
transfer speeds do not exceed the master limits.
The user manual for A10 and A31 specifies maximum
speed of the SPI clock as 100MHz and minimum as 3kHz.
Setting the SPI clock to out-of-spec values can lock up the SoC.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
--
v2:
new patch
v3:
fix constant style
Signed-off-by: Mark Brown <broonie@kernel.org>
trivial fix to spelling mistake in dev_dbg message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After probe time, the pointer to the sh_msiof_chipdata structure in the
sh_msiof_spi_priv structure is used only for checking the SPI master flags.
As these are also available in the spi_master structure, convert the
users to access those, and remove the pointer.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core provides DMA mapping with scatterlists. Start using it instead
of own implementation in spi-pxa2xx. Major difference in addition to
bunch of removed boilerplate code is that SPI core does
mapping/unmapping for all transfers in a message before and after the
message sending where spi-pxa2xx did mapping/unmapping for each
transfers separately.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We will find more use for struct spi_master pointer in pump_transfers()
and code will be more readable if we access it using local pointer than
through the drv_data->master.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI-driver no longer contains the conditions for various CPUs, so
"maybe_unused" attributes is no longer needed.
This patch removes these attributes.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI mode can be obtained directly from spi-device, there is no
need to keep a copy.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Patch reuse existing "chip_select" and "cs_gpio(s)" fields from SPI core.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
The trasfer timeout is fixed at 1000 ms. Reading a 4Mbyte flash over
1MHz SPI bus takes way longer than that. Calculate the timeout from the
actual time the transfer is supposed to take and multiply by 2 for good
measure.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
When testing SPI without DMA I noticed that filling the FIFO on the
spi controller causes timeout.
Always leave room for one byte in the FIFO.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The sun4i spi hardware can trasfer at most 63 bytes of data without DMA
support so report the limitation. Same for sun6i.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using DMA, the transfer_one callback should return 1 because the
transfer hasn't finished yet.
A previous commit changed the function to return 0 when the DMA channels
were correctly prepared.
This manifested in Veyron boards with this message:
[ 1.983605] cros-ec-spi spi0.0: EC failed to respond in time
Fixes: ea98491133 ("spi: rockchip: check return value of dmaengine_prep_slave_sg")
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Few SPI devices provide accelerated read interfaces to read from
SPI-NOR flash devices. These hardwares also support DMA to transfer data
from flash to memory either via mem-to-mem DMA or dedicated slave DMA
channels. Hence, add support for DMA in order to improve throughput and
reduce CPU load.
Use spi_map_buf() to get sg table for the buffer and pass it to SPI
driver.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Before disabling the pm_runtime, we must ensure that there is no transfer
in progress nor will a new one be started. Otherwise the message pump will
fail and in the end, the process requesting the transfer will be stuck.
This behavior has been observed when transferring data from a SPI flash
with dd while removing the module on a DRA7x-evm.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In gerenal, the "rockchip,rockchip-spi" string will match the dts
that's great in spi driver. After all the most of rockchip SoCs ar
same spi controller.
Then, we should keep the old style to match the dts various.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, even if the PXA2xx SPI master supports DMA, it won't be
enabled unless (i) the slave device is enumerated through ACPI, or
(ii) the slave device is registered with board-specific
controller_data specified. Even then, there isn't a field in the
controller_data that explicitly enables dma - it just gets enabled
if the master supports it and controller_data is non-NULL.
This means that drivers which register SPI devices on a bus without
awareness of this controller cannot avail of DMA performance gains.
This patch allows DMA transfers to be used if supported.
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the direct access mode to the Orion SPI
driver which is used on the Marvell Armada based SoCs. In this direct
mode, all data written to (or read from) a specifically mapped MBus
window (linked to one SPI chip-select on one of the SPI controllers)
will be transferred directly to the SPI bus. Without the need to control
the SPI registers in between. This can improve the SPI transfer rate in
such cases.
Both, direct-read and -write mode are supported. But only the write
mode has been tested. This mode especially benefits from the SPI direct
mode, as the data bytes are written head-to-head to the SPI bus,
without any additional addresses.
One use-case for this direct write mode is, programming a FPGA bitstream
image into the FPGA connected to the SPI bus at maximum speed.
This mode is described in chapter "22.5.2 Direct Write to SPI" in the
Marvell Armada XP Functional Spec Datasheet.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the second update round for 4.7-rc1. Most of changes are
about the pending ASoC updates and fixes, including a few new
drivers. Below are some highlights:
ASoC:
- New drivers for MAX98371 and TAS5720
- SPI support for TLV320AIC32x4, along with the module split
- TDM support for STI Uniperf IPs
- Remaining topology API fixes / updates
HDA:
- A couple of Dell quirks and new Realtek codec support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=uNKQ
-----END PGP SIGNATURE-----
Merge tag 'sound-4.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull more sound updates from Takashi Iwai:
"This is the second update round for 4.7-rc1. Most of changes are
about the pending ASoC updates and fixes, including a few new drivers.
Below are some highlights:
ASoC:
- New drivers for MAX98371 and TAS5720
- SPI support for TLV320AIC32x4, along with the module split
- TDM support for STI Uniperf IPs
- Remaining topology API fixes / updates
HDA:
- A couple of Dell quirks and new Realtek codec support"
* tag 'sound-4.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (63 commits)
ALSA: hda - Fix headset mic detection problem for one Dell machine
spi: spi-ep93xx: Fix the PTR_ERR() argument
ALSA: hda/realtek - Add support for ALC295/ALC3254
ASoC: kirkwood: fix build failure
ALSA: hda - Fix headphone noise on Dell XPS 13 9360
ASoC: ak4642: Enable cache usage to fix crashes on resume
ASoC: twl6040: Disconnect AUX output pads on digital mute
ASoC: tlv320aic32x4: Properly implement the positive and negative pins into the mixers
rcar: src: skip disabled-SRC nodes
ASoC: max98371 Remove duplicate entry in max98371_reg
ASoC: twl6040: Select LPPLL during standby
ASoC: rsnd: don't use prohibited number to PDMACHCRn.SRS
ASoC: simple-card: Add pm callbacks to platform driver
ASoC: pxa: Fix module autoload for platform drivers
ASoC: topology: Fix memory leak in widget creation
ASoC: Add max98371 codec driver
ASoC: rsnd: count .probe/.remove for rsnd_mod_call()
ASoC: topology: Check size mismatch of ABI objects before parsing
ASoC: topology: Check failure to create a widget
ASoC: add support for TAS5720 digital amplifier
...
Another quiet release for SPI, almost entirely driver specific changes
with the diffstat dominated by two new drivers which are about two
thirds of it in terms of lines of code:
- New drivers for PIC32 standard and SQI controllers.
- The Cadence driver has had runtime PM support added and quite a few
fixes and cleanups.
- The flash-specific accelerated path support now has a feature query
interface.
- The pxa2xx driver has been moved to use the core DMA mapping support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXQufEAAoJECTWi3JdVIfQXeEH/3PZVHvwQBqpN6S0AunlJQoM
s1bScKYeH2ukx9iw86M/upSCOVt4TGlPrdwzcYCUYll9IJuO/ChDio7PoVlxQeJB
kYUrFi6dzE/bCNzWtrGtyvNlSDsrRccbRBhmKTFQ9DokcJHgzdzhuCuXUR6OKDDw
CxlvDrLwapzOpHIncrhh6dvv1NoZgusOTMzVQAPvLbuiH9WpdnD9MjySklIqd0XU
bp+J4J5+jyBVykOZ2MdYpXf1dRhg0c0kmKXOKuX9woiJhvBFrtZX2GfCw1MXchKZ
/obHOyD7ff+MBCY2nFN95s3rl9Vxn8IAfNWsuQvZaFK0nz1bypaQ6aXIbXXgj/8=
=QO1T
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Another quiet release for SPI, almost entirely driver specific changes
with the diffstat dominated by two new drivers which are about two
thirds of it in terms of lines of code:
- new drivers for PIC32 standard and SQI controllers
- the Cadence driver has had runtime PM support added and quite a few
fixes and cleanups
- flash-specific accelerated path support now has a feature query
interface
- the pxa2xx driver has been moved to use the core DMA mapping support"
* tag 'spi-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (48 commits)
spi: pic32-sqi: Fix linker error, undefined reference to `bad_dma_ops'
spi: dw-pci: Spelling s/paltforms/platforms/g
spi: pic32-sqi: Remove pic32_sqi_setup and pic32_sqi_cleanup
spi: Fix simple typo s/impelment/implement
spi: rockchip: potential NULL dereference on error
spi: zynqmp: disable clocks in error paths
spi: Drop unnecessary dependencies on relaxed I/O accessors
spi: qup: Add spi_master_put in remove function
spi: qup: Handle clocks in pm_runtime suspend and resume
spi: st-ssc4: Fix missing spi_master_put in spi_st_probe error paths
spi: st-ssc4: Allow compile test build
spi: omap2-mcspi: Use dma_request_chan() for requesting DMA channel
spi: davinci: Use dma_request_chan() for requesting DMA channel
spi: pic32: Fix checking return value of devm_ioremap_resource
spi: spi-fsl-dspi: Update DT binding documentation
spi: Drop duplicate code to set master->dev.parent
spi: pic32: Set proper bits_per_word_mask
spi: return error if kmap'd buffers passed to spi_map_buf()
spi: core: add hook flash_read_supported to spi_master
spi: pic32-sqi: silence array overflow warning
...
PTR_ERR should access the value just tested by IS_ERR.
The semantic patch that makes this change is available
in scripts/coccinelle/tests/odd_ptr_err.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This time round the update brings in following changes:
- New tegra driver for ADMA device
- Support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI Central
Direct Memory Access Engine and few updates to this driver.
- New cyclic capability to sun6i and few updates.
- Slave-sg support in bcm2835.
- Updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Sy7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
Even if DMA support is disabled code using DMA mapping APIs compiles fine,
but fails in linking.
-------
drivers/built-in.o: In function `ring_desc_ring_free':
spi-pic32-sqi.c:(.text+0x2cfbe0): undefined reference to `bad_dma_ops'
spi-pic32-sqi.c:(.text+0x2cfbe4): undefined reference to `bad_dma_ops'
drivers/built-in.o: In function `pic32_sqi_probe':
spi-pic32-sqi.c:(.text+0x2cfe48): undefined reference to `bad_dma_ops'
spi-pic32-sqi.c:(.text+0x2cfeb0): undefined reference to `bad_dma_ops'
spi-pic32-sqi.c:(.text+0x2cff38): undefined reference to `bad_dma_ops'
--------
Correct dependency by adding 'depends on HAS_DMA' in Kconfig.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code does not use ctldata at all, so remove spi_set_ctldata call.
spi_setup() will set spi->bits_per_word = 8 if it was not set, so remove
!spi->max_speed_hz checking.
The spi core allows absent of spi->max_speed_hz setting, if it was not set
spi_setup() assigns spi->master->max_speed_hz to it.
spi core allows spi->max_speed_hz > spi->master->max_speed_hz, in this case
spi core will limit the transfer speed to ensure xfer->speed_hz won't
greater than spi->master->max_speed_hz so remove checking if
spi->max_speed_hz is higher than spi->master->max_speed_hz.
As a result, both pic32_sqi_setup() and pic32_sqi_cleanup() can be removed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes a simple typo in one of the comments.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We were calling dma_release_channel(rs->dma_tx.ch) when "rs->dma_tx.ch"
is potentially NULL. There is actually a call to that in the unwind
code at the bottom of the function so we can just re-arrange this a bit
and remove the call. Also there is no need to set rs->dma_tx.ch to
NULL on this error path.
Fixes: e4c0e06f94 ('spi: rockchip: fix probe deferral handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The if pclk enable fails the refclk is not disabled.
Fix the same.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The relaxed I/O accessors are available on all architectures now.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Release memory allocated for spi master by calling spi_master_put in
.remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clocks must ne disabled in pm_runtime to achieve some power saving.
Enable the clocks when the device is runtime resumed during a transfer.
Signed-off-by: Pramod Gurav <pramod.gurav@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no build dependency for this driver, so enable COMPILE_TEST to get
better build coverage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With the new dma_request_chan() the client driver does not need to look for
the DMA resource and it does not need to pass filter_fn anymore.
By switching to the new API the driver can now support deferred probing
against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With the new dma_request_chan() the client driver does not need to look for
the DMA resource and it does not need to pass filter_fn anymore.
By switching to the new API the driver can now support deferred probing
against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_ioremap_resource() returns ERR_PTR on error.
Also remove the redundant dev_err message, the implementation of
devm_ioremap_resource() already print error messages on error paths.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver only supports 8/16/32 bits_per_word, so set
master->bits_per_word_mask accordingly. With this change, we can remove
the spi->bits_per_word checking in pic32_spi_setup as it's done by spi
core.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Certain Intel Sunrisepoint PCH variants report zero chip selects in SPI
capabilities register even they have one per port. Detection in
pxa2xx_spi_probe() sets master->num_chipselect to 0 leading to -EINVAL
from spi_register_master() where chip select count is validated.
Fix this by not using SPI capabilities register on Sunrisepoint. They don't
have more than one chip select so use the default value 1 instead of
detection.
Fixes: 8b136baa58 ("spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Current spi_map_buf() implementation supports creates sg_table for
vmalloc'd and kmalloc'd buffers. Therefore return error if kmap'd buffer
(or any other buffer) is passed to spi_map_buf().
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We read one element beyond the end of the array when we access
"rdesc[i + 1]" so it causes a static checker warning. It's harmless
because we write over it again on the next line. But let's just silence
the warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI controller managed by the spi-orion is used on the new ARM64
Marvell Armada 7K/8K SoCs. In order to allow this driver to be built
for this platform, we allow it to be selected for ARCH_MVEBU=y
configurations.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver implements SPI master interface for Quad SPI
controller, specifically for accessing quad SPI flash.
It uses descriptor-based DMA transfer mode and supports
half-duplex communication for single, dual and quad SPI
transactions.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This implements more efficient reads of SPI-attached flash content.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The newly added runtime PM support for the cadence spi driver
causes harmless warnings when PM is disabled:
drivers/spi/spi-cadence.c:681:12: warning: 'cnds_runtime_suspend' defined but not used
drivers/spi/spi-cadence.c:652:12: warning: 'cnds_runtime_resume' defined but not used
This adds __maybe_unused annotations to the respective functions
to shut up the warnings, while leaving the code in place for
compile testing and avoiding ugly #ifdefs.
Fixes: d36ccd9f7e ("spi: cadence: Runtime pm adaptation")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This allows defining SPI devices connected to a DLN2 using devicetree.
This already works for i2c because of a similar patch:
3b10db23: i2c: dln2: set the device tree node of the adapter
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Acked-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The source and destination masters are reflecting buses or their layers to
where the different devices can be connected. The patch changes the master
names to reflect which one is related to which independently on the transfer
direction.
The outcome of the change is that the memory data width is now always limited
by a data width of the master which is dedicated to communicate to memory.
The patch will not break anything since all current users have the same data
width for all masters. Though it would be nice to revisit avr32 platforms to
check what is the actual hardware topology in use there. It seems that it has
one bus and two masters on it as stated by Table 8-2, that's why everything
works independently on the master in use. The purpose of the sequential patch
is to fix the driver for configuration of more than one bus.
The change is done in the assumption that src_master and dst_master are
reflecting a connection to the memory and peripheral correspondently on avr32
and otherwise on the rest.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We clamp frame_len_words to a maximum of 4096, but do not actually
limit the number of words written or read through the DATA registers
or the length added to spi_message::actual_length. This results in
silent data corruption for commands longer than this maximum.
Recalculate the length of each transfer, taking frame_len_words into
account. Use this length in qspi_{read,write}_msg(), and to increment
spi_message::actual_length.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Each transfer can specify 8, 16 or 32 bits per word independently of
the default for the device being addressed. However, currently we
calculate the number of words in the frame assuming that the word size
is the device default.
If multiple transfers in the same message have differing
bits_per_word, we bitwise-or the different values in the WLEN register
field.
Fix both of these. Also rename 'frame_length' to 'frame_len_words' to
make clear that it's not a byte count like spi_message::frame_length.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Let all SPI masters ignore their children: when it comes
to power management: SPI children have no business doing
keeping their parents awake: they are completely autonomous
devices that just use their parent to talk, and the latter
usecase must be power managed by the host itself on a
per-message basis.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 3525e0aac9.
The DMA transfer for RX buffer was not handled correctly in this change.
The actual transfer length for DMA RX can be less than xfer->len in the
specific condition and the last words will be filled after the DMA
completion, but the commit doesn't consider it and the dmaengine is
started with rx_sg mapped by spi core.
The solution for this at least requires more lines than this commit
has inserted. So revert it for now.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No functional change.
Fixing some style related issues
CHECK: multiple assignments should be avoided
+ new_ctrl_reg = ctrl_reg = cdns_spi_read(xspi, CDNS_SPI_CR);
CHECK: Alignment should match open parenthesis
+static void cdns_spi_config_clock_freq(struct spi_device *spi,
+ struct spi_transfer *transfer)
CHECK: Please use a blank line after function/struct/union/enum declarations
+}
+static int cdns_prepare_message(struct spi_master *master,
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are use cases when chip select should be triggered between transfers
in single SPI message. Current implementation does this only on last
transfer in message ignoring cs_change value provided in current transfer.
Signed-off-by: Andrey Vostrikov <andrey.vostrikov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return the error code for cdns_spi_suspend and cdns_spi_resume.
Also fixes a comment where which claims that the error code is
returned.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the clocks are enabled and disabled per transaction
, remove the clock enable and disable from resume and suspend
hooks.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the clocks are enabled at probe and disabled
at remove. This patch moves the clock enable to the
start of transaction and disables at the end.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
cdns_spi_chipselect has parameter is_high however the comment
describes it as is_on.
Also fixes the below warning.
drivers/spi/spi-cadence.c:182: warning: No description found for
parameter 'is_high'
drivers/spi/spi-cadence.c:182: warning: Excess function parameter 'is_on'
description in 'cdns_spi_chipselect'
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The clock disabling is missed out in some
error cases at probe. Fix the same.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the _MASK and _OFFSET from the macros.
It improves readability, removes some checkpatch
error for exceeding 80 chars and also prevents some
linebreaks.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CHECK: Comparison to NULL could be written "!master"
+ if (master == NULL)
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PIC32 SPI driver is capable of performing SPI transfers
using PIO or external DMA engine. GPIO controlled /CS support
is made default in the driver for correct operation of the
controller. This can be enabled by adding "cs-gpios" property
of the SPI node in board dts file.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dma_request_chan instead of dma_request_slave_channel,
in this case we can check EPROBE_DEFER without static
warning.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix cs_change management so that it is in line with other spi drivers.
In the spi core api helpers such as spi_bus_lock/unlock and spi_sync_locked
or cs_change field in spi_transfer help to manage chip select from the
device driver.
The driver was setting the chip select to idle if the message queue was
empty despite cs_change or other status field set by spi_bus_lock/unlock
or spi_sync_locked.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It brought nearly infinite loops, and was possible to be
occurred only if the SPI transaction total size are not
alighed with 4. Loops are here at while (tmp--),
tmp is unsigned, and set it with minus value.
The loops are executed as a result of unexpected RX interrupt
occurrence after that. This interrupt may be hardware eratta
and is not fixed.
Fix mspi->len from minus value to 0 and print warning message.
Signed-off-by: Nobuteru Hayashi <hayashi.nbb@ncos.nec.co.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
