Merge remote-tracking branches 'spi/topic/rspi', 'spi/topic/sc18is602', 'spi/topic/sh-msiof', 'spi/topic/spidev-test' and 'spi/topic/st-ssc4' into spi-next

MAINTAINERS

@@ -11124,6 +11124,7 @@ F:	Documentation/spi/
 F:	drivers/spi/
 F:	include/linux/spi/
 F:	include/uapi/linux/spi/
+F:	tools/spi/
 
 SPIDERNET NETWORK DRIVER for CELL
 M:	Ishizaki Kou <kou.ishizaki@toshiba.co.jp>

drivers/spi/Kconfig

@@ -566,7 +566,7 @@ config SPI_SC18IS602
 config SPI_SH_MSIOF
 	tristate "SuperH MSIOF SPI controller"
 	depends on HAVE_CLK && HAS_DMA
-	depends on SUPERH || ARCH_RENESAS || COMPILE_TEST
+	depends on ARCH_SHMOBILE || ARCH_RENESAS || COMPILE_TEST
 	help
 	  SPI driver for SuperH and SH Mobile MSIOF blocks.
 

drivers/spi/spi-rspi.c

@@ -295,14 +295,24 @@ static int rspi_set_config_register(struct rspi_data *rspi, int access_size)
 static int rspi_rz_set_config_register(struct rspi_data *rspi, int access_size)
 {
 	int spbr;
+	int div = 0;
+	unsigned long clksrc;
 
 	/* Sets output mode, MOSI signal, and (optionally) loopback */
 	rspi_write8(rspi, rspi->sppcr, RSPI_SPPCR);
 
+	clksrc = clk_get_rate(rspi->clk);
+	while (div < 3) {
+		if (rspi->max_speed_hz >= clksrc/4) /* 4=(CLK/2)/2 */
+			break;
+		div++;
+		clksrc /= 2;
+	}
+
 	/* Sets transfer bit rate */
-	spbr = DIV_ROUND_UP(clk_get_rate(rspi->clk),
-			    2 * rspi->max_speed_hz) - 1;
+	spbr = DIV_ROUND_UP(clksrc, 2 * rspi->max_speed_hz) - 1;
 	rspi_write8(rspi, clamp(spbr, 0, 255), RSPI_SPBR);
+	rspi->spcmd |= div << 2;
 
 	/* Disable dummy transmission, set byte access */
 	rspi_write8(rspi, SPDCR_SPLBYTE, RSPI_SPDCR);

drivers/spi/spi-sc18is602.c

@@ -23,6 +23,7 @@
 #include <linux/pm_runtime.h>
 #include <linux/of.h>
 #include <linux/platform_data/sc18is602.h>
+#include <linux/gpio/consumer.h>
 
 enum chips { sc18is602, sc18is602b, sc18is603 };
 
@@ -50,6 +51,8 @@ struct sc18is602 {
 	u8			buffer[SC18IS602_BUFSIZ + 1];
 	int			tlen;	/* Data queued for tx in buffer */
 	int			rindex;	/* Receive data index in buffer */
+
+	struct gpio_desc	*reset;
 };
 
 static int sc18is602_wait_ready(struct sc18is602 *hw, int len)
@@ -257,6 +260,12 @@ static int sc18is602_probe(struct i2c_client *client,
 	hw = spi_master_get_devdata(master);
 	i2c_set_clientdata(client, hw);
 
+	/* assert reset and then release */
+	hw->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(hw->reset))
+		return PTR_ERR(hw->reset);
+	gpiod_set_value_cansleep(hw->reset, 0);
+
 	hw->master = master;
 	hw->client = client;
 	hw->dev = dev;

drivers/spi/spi-st-ssc4.c

@@ -175,10 +175,7 @@ static int spi_st_transfer_one(struct spi_master *master,
 
 static void spi_st_cleanup(struct spi_device *spi)
 {
-	int cs = spi->cs_gpio;
-
-	if (gpio_is_valid(cs))
-		devm_gpio_free(&spi->dev, cs);
+	gpio_free(spi->cs_gpio);
 }
 
 /* the spi->mode bits understood by this driver: */
@@ -201,14 +198,15 @@ static int spi_st_setup(struct spi_device *spi)
 		return -EINVAL;
 	}
 
-	if (devm_gpio_request(&spi->dev, cs, dev_name(&spi->dev))) {
+	ret = gpio_request(cs, dev_name(&spi->dev));
+	if (ret) {
 		dev_err(&spi->dev, "could not request gpio:%d\n", cs);
-		return -EINVAL;
+		return ret;
 	}
 
 	ret = gpio_direction_output(cs, spi->mode & SPI_CS_HIGH);
 	if (ret)
-		return ret;
+		goto out_free_gpio;
 
 	spi_st_clk = clk_get_rate(spi_st->clk);
 
@@ -217,7 +215,8 @@ static int spi_st_setup(struct spi_device *spi)
 	if (sscbrg < 0x07 || sscbrg > BIT(16)) {
 		dev_err(&spi->dev,
 			"baudrate %d outside valid range %d\n", sscbrg, hz);
-		return -EINVAL;
+		ret = -EINVAL;
+		goto out_free_gpio;
 	}
 
 	spi_st->baud = spi_st_clk / (2 * sscbrg);
@@ -266,6 +265,10 @@ static int spi_st_setup(struct spi_device *spi)
 	 readl_relaxed(spi_st->base + SSC_RBUF);
 
 	 return 0;
+
+out_free_gpio:
+	gpio_free(cs);
+	return ret;
 }
 
 /* Interrupt fired when TX shift register becomes empty */

tools/spi/spidev_test.c

@@ -19,6 +19,7 @@
 #include <getopt.h>
 #include <fcntl.h>
 #include <sys/ioctl.h>
+#include <linux/ioctl.h>
 #include <sys/stat.h>
 #include <linux/types.h>
 #include <linux/spi/spidev.h>