Add more register address and mask which can be different
for newer chip to hw_reg table.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to prepare ath10k to support newer chip set.
Values like CE_COUNT, MSI_ASSIGN_CE_MAX and
RTC_STATE_V_ON can be different for different
chips.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wait_event_timeout(), introduced in 'commit 5e3dd157d7 ("ath10k: mac80211
driver for Qualcomm Atheros 802.11ac CQA98xx devices")' never returns < 0
so the only failure condition to be checked is == 0 (timeout). Further the
return type is long not int - an appropriately named variable is added
and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wait_event_timeout(), introduced in 'commit 5e3dd157d7 ("ath10k: mac80211
driver for Qualcomm Atheros 802.11ac CQA98xx devices")' never returns < 0
so the only failure condition to be checked is ==0 (timeout). Further the
return type is long not int - an appropriately named variable is added
and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible to force an out of bounds MMIO
read/write via debugfs. E.g. on QCA988X this could
be triggered with:
echo 0x2080e0 | tee /sys/kernel/debug/ieee80211/*/ath10k/reg_addr
cat /sys/kernel/debug/ieee80211/*/ath10k/reg_value
BUG: unable to handle kernel paging request at ffffc90001e080e0
IP: [<ffffffff8135c860>] ioread32+0x40/0x50
...
Call Trace:
[<ffffffffa00d0c7f>] ? ath10k_pci_read32+0x4f/0x70 [ath10k_pci]
[<ffffffffa0080f50>] ath10k_reg_value_read+0x90/0xf0 [ath10k_core]
[<ffffffff8115c2c1>] ? handle_mm_fault+0xa91/0x1050
[<ffffffff81189758>] __vfs_read+0x28/0xe0
[<ffffffff812e4694>] ? security_file_permission+0x84/0xa0
[<ffffffff81189ce3>] ? rw_verify_area+0x53/0x100
[<ffffffff81189e1a>] vfs_read+0x8a/0x140
[<ffffffff8118acb9>] SyS_read+0x49/0xb0
[<ffffffff8104e39c>] ? trace_do_page_fault+0x3c/0xc0
[<ffffffff8196596e>] system_call_fastpath+0x12/0x71
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable VHT support for IBSS, while mac80211/cfg80211 and
wpa_supplicant already support this.
In my test env, qca988x 2x2 I get:
(udp) ath10k-1 >>>> ath10k-2 (server) - speed: 419 Mbits/sec
(tcp) ath10k-1 >>>> ath10k-2 (server) - speed: 404 Mbits/sec
During tests I used wpa_supplicant (latest git version), which
already support IBSS VHT, and choose highest available BW. Also tested with
qca6174.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HTT version itself isn't sufficient to know what
HTT version given firmware blob uses. Hence print
the recently introduced HTT op version code.
While at it make the info string a bit more
consistent and clear.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This should help when analysing problems from
users and spot fw api blob problems easier.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the support of channel switching functionality, similar
to ath9k support.
Tested with TP-Link TL-WN722N and TL-WN821N.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Need to reorder init sequence to run wil_platform_init
before pci_enable_device. Assumption is platform init
may be required before device may be enabled.
Another issue, platform uninit should be called after
pci_disable_device because platform uninit may render
pci device non-accessible.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Provide platform hooks for module init/exit.
If platform require to perform some specific actions
in global context, this is where to do so.
Example may be turning on power for the PCIE based
on DT information.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass hidden SSID information to FW for proper operation.
In order to be able to scan/connect to the hidden SSID, SSID
setting is added when scan is requested from FW. SSID
scanning currently supports single SSID due to FW limitation.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Provide detailed statistics for the Rx frames per MCS
Statistics printed in "stations" debugfs entry
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware defines new memory region, mac_rgf_ext
that need to be accessed from the host for debug purposes.
Add corresponded mapping
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Control Bcast ring size in similar way as Rx and Tx ones,
through "bcast_ring_order" modparam, actual ring size is 1 << order
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When one client is associated and connected to an ar6003 hw version
2.0 with firmware 3.1.1.149, and another client tries to connect, the
first client's MAC address is lost in the station list because the
"aid" is always "1". The structure "wmi_connect_event" has the "aid"
as the second byte in the message, but it should be the first byte.
This patch has been tested with linux-3.10.40
Signed-off-by: Brent Taylor <motobud@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Found during code review. This was pretty much
impossible to happen but better safe than sorry.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the midst of chanctx patch review channel
switching became broken which I failed to notice
until now.
Function ath10k_mac_vif_chan() reports current
chandef which isn't updated until after
switch_vif_chanctx() is returned from.
Consequently the driver just restarted operation
on channels it was residing already instead of
switching to the new ones.
Fixes: 500ff9f938 ("ath10k: implement chanctx API")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In practice there's no point in having a copy of
chanctx_conf.
Most of the time the channel pointer (and band
along with it) is accessed and this can't change
after a chanctx is created because switching is
done using explicit chanctx swapping via
switch_vif_chanctx().
The only thing that can change within a
chanctx_conf and is used by the driver is
radar_enabled and channel width. These are however
always accessed in adequate mac80211 callback
context which guarantees safe access to the
chanctx data.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Channel contexts aren't iterable until after
they've been added to the driver. The code assumed
otherwise.
This problem could result in:
* rx_channel being NULL and forcing Rx path to go
the slow way to get channel on QCA988X,
* report incorrect channel when running
multi-channel on QCA61X4 hw2.1,
* report incorrect channel after AP channel
switch.
Fixes: 500ff9f938 ("ath10k: implement chanctx API")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mete_data is extracted from ce descriptor and stored in variable 'id'.
later, id is not used anywhere in the same function.
Fixes: d84a512dca ("ath10k: remove transfer_id from ath10k_hif_cb::tx_completion")
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When wmi mgmt event function fails to parse given skb,
it should be freed on failure condition to avoid memory
leaks. Found this during the code review.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
AR93xx and newer needs to stop rx before tx to avoid getting the DMA
engine or MAC into a stuck state.
This should reduce/fix the occurence of "Failed to stop Tx DMA" logspam.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k:
* qca6174 power consumption improvements, enable ASPM etc (Michal)
wil6210:
* support Wi-Fi Simple Configuration in STA mode
iwlwifi:
* a few fixes (re-enablement of interrupts for certain new
platforms that have special power states)
* Rework completely the RBD allocation model towards new
multi RX hardware.
* cleanups
* scan reworks continuation (Luca)
mwifiex:
* improve firmware debug functionality
rtlwifi:
* update regulatory database
brcmfmac:
* cleanup and new feature support in PCIe code
* alternative nvram loading for router support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVb1cPAAoJEG4XJFUm622bP0oIAKhUBlC3rtrOJd+9kREAGUJQ
Dk2xZr/p6hdb4dSHHKKroBr5mfryHknSs+AI5akJMph36DoBMD+Mwb4HlcL9cI5J
RXIjIvQEADsK+6ME7cqnw2htWlYsX8aJI96/2Eusveo/zHyAG3+eBC3wkyqWBlBK
EGV5ziClSe5pE5yGWj5tyr9me+qRQiO+dFJK1AoRE3Zq4pjj+5VDZoVQN0GNZGP7
lgeNOzvPxWt+ZseslP8IeCedN5c+NpacD889NnQJyMXaouSp7LmMod000bjnKK8o
9sRHsKxI5qHgC4mUa3Tk3cEnFqVYAo8KKOVaBVtKsMc4XoO/Qov6Z0AtXig5Xnk=
=CM/T
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-06-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
new driver mt7601u for MediaTek Wi-Fi devices MT7601U
ath10k:
* qca6174 power consumption improvements, enable ASPM etc (Michal)
wil6210:
* support Wi-Fi Simple Configuration in STA mode
iwlwifi:
* a few fixes (re-enablement of interrupts for certain new
platforms that have special power states)
* Rework completely the RBD allocation model towards new
multi RX hardware.
* cleanups
* scan reworks continuation (Luca)
mwifiex:
* improve firmware debug functionality
rtlwifi:
* update regulatory database
brcmfmac:
* cleanup and new feature support in PCIe code
* alternative nvram loading for router support
====================
Conflicts:
drivers/net/wireless/iwlwifi/Kconfig
Trivial conflict in iwlwifi Kconfig, two commits adding
the same two chip numbers to the help text, but order
transposed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of of qca988x solutions are having global reset issue
during target initialization. Bypassing PLL setting before
downloading firmware and letting the SoC run on REF_CLK is fixing
the problem. Corresponding firmware change is also needed to set
the clock source once the target is initialized. Since 10.2.4
firmware is having this ROM patch, applying skip_clock_init only
for 10.2.4 firmware versions.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
more things for -next:
* disconnect TDLS stations on CSA to avoid issues
* fix a memory leak introduced in a recent commit
* switch rfkill and cfg80211 to PM ops
* in an unlikely scenario, prevent a bookkeeping
value to get corrupted leading to dropped packets
* fix a crash in VLAN assignment
* switch rfkill-gpio to more modern gpiod API
* send disconnected event to userspace with proper
local/remote indication
-----BEGIN PGP SIGNATURE-----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=KmwY
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
As we get closer to the merge window, here are a few
more things for -next:
* disconnect TDLS stations on CSA to avoid issues
* fix a memory leak introduced in a recent commit
* switch rfkill and cfg80211 to PM ops
* in an unlikely scenario, prevent a bookkeeping
value to get corrupted leading to dropped packets
* fix a crash in VLAN assignment
* switch rfkill-gpio to more modern gpiod API
* send disconnected event to userspace with proper
local/remote indication
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This could lead userspace initram images getting
built without necessary firmware files included
leading to probing failures of ath10k on boot with
QCA61X4.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some cases some channel survey data was
reported incorrect.
Channel info events were expected to come in pairs
without and with COMPLETE flag set respectively
for each channel visit during scan.
The known deviation from this is rule for last
scan chan info and first (next) scan chan info
both have COMPLETE flag set. This was either
programmed with the intent of providing BSS cycle
count info or this is an artefact of firmware scan
state machine. Either way this is useless due to
short wraparound time, wraparound quirks and no
overflow notification.
Survey dumps now include only data gathered during
scan channel visits that can be computed
correctly.
This should improve hostapd ACS a little bit.
Reported-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When QCA988X cycle counter HW register wraps
around it resets to 0x7fffffff instead of 0. All
other cycle counter related registers are divided
by 2 so they never wraparound themselves. QCA61X4
has a uniform CC and it wraparounds in a regular
fashion though.
Worst case wraparound time is approx 24 seconds
(2**31 / 88MHz). Since scan channel visit times
are max 5 seconds (offchannel case) it is
guaranteed there's been at most 1 wraparound and
it is possible to compute survey active time
value. It is, however, impossible to determine the
point at which Rx Clear Count has been divided by
two so it is not reported upon wraparound.
This fixes some occasional incorrect survey data
on QCA988X as some channels (depending on how/when
scan/offchannel requests were requested) would
have approx 24 sec active time which wasn't
actually the case.
This should improve hostapd ACS a little bit.
Reported-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The macro isn't WMI specific. Instead it is
related to hardware chip so move the macro
accordingly. While at it document the magic value.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When we disconnect from the AP, drivers call cfg80211_disconnect().
This doesn't know whether the disconnection was initiated locally
or by the AP though, which can cause problems with the supplicant,
for example with WPS. This issue obviously doesn't show up with any
mac80211 based driver since mac80211 doesn't call this function.
Fix this by requiring drivers to indicate whether the disconnect is
locally generated or not. I've tried to update the drivers, but may
not have gotten the values correct, and some drivers may currently
not be able to report correct values. In case of doubt I left it at
false, which is the current behaviour.
For libertas, make adjustments as indicated by Dan Williams.
Reported-by: Matthieu Mauger <matthieux.mauger@intel.com>
Tested-by: Matthieu Mauger <matthieux.mauger@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[ar5008 and ar9002]_hw_spur_mitigate have big portion of identical code.
This patch will move common part of ar5008_hw_spur_mitigate to
ar5008_hw_cmn_spur_mitigate and reuse it in ar9002_hw_spur_mitigate.
As noticed by Joe Perches I reuse ar9002_hw_spur_mitigate (const) version of
declarations for pilot_mask_reg and chan_mask_reg.
There should be no other difference with original code.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In d8a2c51cdc ('ath9k_htc: Use atomic operations for op_flags') we
changed things like this:
- if (priv->op_flags & OP_TSF_RESET) {
+ if (test_bit(OP_TSF_RESET, &priv->op_flags)) {
The problem is that test_bit() takes a bit number and not a mask. It
means that when we do:
set_bit(OP_TSF_RESET, &priv->op_flags);
Then it sets the (1 << 6) bit instead of the 6 bit so we are setting a
bit which is past the end of the unsigned long.
Fixes: d8a2c51cdc ('ath9k_htc: Use atomic operations for op_flags')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added, and the assignments
as well as error checking fixed up.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/carl9170/usb.c:675
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_CARL9170=m
Patch is against 4.1-rc3 (localversion-next is -next-20150512)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* enable channel 144 on 5 GHz
* enable Adaptive Noise Immunity (ANI) by default
* add Wake on Wireless LAN (WOW) patterns support
* add basic Tunneled Direct Link Setup (TDLS) support
* add multi-channel support for QCA6174
* enable IBSS RSN support
* enable Bluetooth Coexistance whenever firmware supports it
* add more versatile way to set bitrates used by the firmware
ath9k:
* spectral scan: add support for multiple FFT frames per report
iwlwifi:
* major rework of the scan code (Luca)
* some work on the thermal code (Chaya Rachel)
* some work on the firwmare debugging infrastructure
brcmfmac:
* SDIO suspend and resume fixes
* wiphy band info and changes in regulatory settings
* add support for BCM4324 SDIO and BCM4358 PCIe
* enable support of PCIe devices on router platforms (Hante)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVXbP3AAoJEG4XJFUm622b5KoH/1qlTHsKcyvdxlhQOgYNGCXA
HNMwcxtwFyRYHFeVTGOQp2BVknEoqWTwGv1m4FQ1pBSSwuUvAyw4BHNSRat/zaNc
wLnZgUYKH5VHeoE/cpe/Asowau+u8hru1adPsVSjudTXMinKrNaDUfjSs2U+UR0+
BaC3PtsANk7wH82+bZq3qXYjcaZITObDe3WBmMNMG0nTimS6pScgnTUnfHch+CEA
0sTOlZF+QTGiH/c5tw2SAoRft4OG+oTnWYQ+vEEQsVev7Yegasa/kg4NdDVdjBNk
9VH9aDlQfGgxodCoeJuQCDzUZL8ixnvYTLeUTxqypzx9Cw0TsLDwoMQA+Ux3G8w=
=JSya
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-05-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
ath10k:
* enable channel 144 on 5 GHz
* enable Adaptive Noise Immunity (ANI) by default
* add Wake on Wireless LAN (WOW) patterns support
* add basic Tunneled Direct Link Setup (TDLS) support
* add multi-channel support for QCA6174
* enable IBSS RSN support
* enable Bluetooth Coexistance whenever firmware supports it
* add more versatile way to set bitrates used by the firmware
ath9k:
* spectral scan: add support for multiple FFT frames per report
iwlwifi:
* major rework of the scan code (Luca)
* some work on the thermal code (Chaya Rachel)
* some work on the firwmare debugging infrastructure
brcmfmac:
* SDIO suspend and resume fixes
* wiphy band info and changes in regulatory settings
* add support for BCM4324 SDIO and BCM4358 PCIe
* enable support of PCIe devices on router platforms (Hante)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware revisions pad 4th hw address in
Native Wifi Rx decap. This is the case with 10.x
and it was assumed that this is true for all
firmware images.
However QCA988X with 999.999.0.636 and QCA61X4
with WLAN.RM.2.0-00088 don't have the padding.
Hence add a feature flag indicating that the
padding isn't present so firmware images can
advertise it appropriately. This way driver will
behave as it was before with old firmware blobs
and doesn't cause any regressions from user
perspective.
Effectively this patch enables QCA988X with
999.999.0.636 and QCA61X4 with WLAN.RM.2.0-00088
to set up client bridging provided user has an
updated firmware blob.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By using SOC_WAKE register it is possible to bring
down power consumption of QCA61X4 from 36mA to
16mA when associated and idle.
Currently the sleep threshold/grace period is at a
very conservative value of 60ms.
Contrary to QCA61X4 the QCA988X firmware doesn't
have Rx/beacon filtering available for client mode
and SWBA events are used for beaconing in AP/IBSS
so the SoC needs to be woken up at least every
~100ms in most cases. This means that QCA988X
is at a disadvantage and the power consumption
won't drop as much as for QCA61X4.
Due to putting irq-safe spinlocks on every MMIO
read/write it is expected this can cause a little
performance regression on some systems. I haven't
done any thorough measurements but some of my
tests don't show any extreme degradation.
The patch removes some explicit pci_wake calls
that were added in 320e14b8db51aa ("ath10k: fix
some pci wake/sleep issues"). This is safe because
all MMIO accesses are now wrapped and the device
is woken up automatically if necessary.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 can update vif powersave state while
disconnected. Firmware doesn't behave nicely and
consumes more power than necessary if PS is
disabled on a non-started vdev. Hence
force-enable PS for non-running vdevs.
This reduces power drain on QCA61X4 from 88mA to
36mA when interface is up and not associated.
QCA988X wasn't measured.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is actually safe to enable ASPM after the
device is booted up.
This reduces power drain of QCA61X4 when driver is
simply loaded (no interface is up) from 31mA to
14mA. QCA988X wasn't measured but doesn't seem to
regress in any other way.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix format specifier used for dma_addr_t, namely use %pad
Debug print virtual address for the same buffer as well.
Fixes: dc16427bbe ("wil6210: Add pmc debug mechanism memory management")
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Four minor merge conflicts:
1) qca_spi.c renamed the local variable used for the SPI device
from spi_device to spi, meanwhile the spi_set_drvdata() call
got moved further up in the probe function.
2) Two changes were both adding new members to codel params
structure, and thus we had overlapping changes to the
initializer function.
3) 'net' was making a fix to sk_release_kernel() which is
completely removed in 'net-next'.
4) In net_namespace.c, the rtnl_net_fill() call for GET operations
had the command value fixed, meanwhile 'net-next' adjusted the
argument signature a bit.
This also matches example merge resolutions posted by Stephen
Rothwell over the past two days.
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx clear count reported in wmi_chan_info_event is actually channel_busy_count
not rx_frame_count. Send rx_clear_count through time_busy of survey_info
and set SURVEY_INFO_TIME_BUSY in filled.
iw wlan0 survey dump
urvey data from wlan0
frequency: 5180 MHz [in use]
noise: -103 dBm
channel active time: 150 ms
channel busy time: 22 ms
Survey data from wlan0
frequency: 5200 MHz
noise: -102 dBm
channel active time: 146 ms
channel busy time: 0 ms
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Spectral scan supported by ath10k has capability to monitor and report
through whole bands and channels, but current buffer size is too small
to save reported spectral scan data.
This results in dropping 5G channel reports at all when dual band card
is used, so that users are not able to analyze spectral environments.
Hence increase the buffer size to fix the problem.
A spectral data size is vary based on the number of bins, so the unit
buffer size, 1140, is chose to minimize relay buffer fragmentation.
The total buffer size is also chose in tradeoff with spectral scan
support vs. kernel memory consumption.
Since theoretical maximum buffer size, 9.5MB, can be consumed with
512 bins in dual bands, we target to cover up to 128 bins for all
channels in dual bands and due to the buffer size limitation,
spectral scan with bin number bigger than 128 needs to be run on
single band each.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Normal FFT reports generate a LOT of data, to save resources
enable short repeat by default also on ath9k_htc (it's already
enabled by default on ath9k). This can always be changed from
userspace if needed.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
E/M noise is a pretty good source of entropy so we mix the FFT
measurements of the E/M spectrum to /dev/random pool. Note that
this doesn't increase the pool's entropy count but it still helps
on improving the output of /dev/(u)random.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Temp buffer is only used for fixing malformed frames, there is no
need to memset it every time.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
