When resetting and reloading the GuC, the GuC submission management code
also needs to destroy and recreate the GuC client(s). Currently this is
done by a separate call from the GuC loader, but really, it's just an
internal detail of the submission code. So here we remove the call from
the loader (which is too late, really, because the GuC has already been
reloaded at this point) and put it into guc_submission_init() instead.
This means that any preexisting client is destroyed *before* the GuC
(re)load and then recreated after, iff the firmware was successfully
loaded. If the GuC reload fails, we don't recreate the client, so
fallback to execlists mode (if active) won't leak the client object
(previously, the now-unusable client would have been left allocated,
and leaked if the driver were unloaded).
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
The last stage of the GuC loader also sanitises the GuC submission
settings, so should be called unconditionally (even on platforms
without a GuC) to ensure consistent settings; in particular, this
prevents any attempt to use GuC submission on GuCless platforms!
Also fix error path handling and clarify DRM_INFO fallback message.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fix the failure mode where the display appears split, or shifted about
2/3 of the screen, and the color components are cycled. Turns out we
were missing the crucial BXT_DEFEATURE_DPI_FIFO_CTR bit in the
EOT_DISABLE register.
Per bspec, with the bit set, the "mipi_dpf_vblank_start" signal is
asserted only when the complete frame is transferred in the DPHY line
and also the DPI FIFO is flushed out at the end of each frame.
The problem was mitigated by keeping the panel fitter enabled, but that
only limited the issue to a shift of about 0..10 pixels. With the fix
here, the panel fitter workaround does not seem to be needed at all.
While at it, set BXT_DPHY_DEFEATURE_EN in EOT_DISABLE register which is
also needed per the BXT DSI mode set sequence.
Issue: VIZ-7610
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464965825-31035-1-git-send-email-jani.nikula@intel.com
Just fallout from switching from asciidoc to sphinx/rst.
v2: Found more. Also s/\//#/ in the vgpu ascii-art - sphinx treats
those as comments and switch to variable-width, which wreaks the
layout.
v3: Undo some of the hacks, rebasing onto latest version of Jani's
series fixed it.
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
It's kinda pointless to have 2 separate mallocs for these. And when we
add more per-plane state in the future it's even more pointless.
Right now there's no such thing planned, but both Gustavo's per-crtc
fence patches, and some nonblocking commit helpers I'm playing around
with will add more per-crtc stuff. It makes sense to also consolidate
planes, just for consistency.
In the future we can use this to store a pointer to the preceeding
state, making an atomic update entirely free-standing. This will be
needed to be able to queue them up with a depth > 1.
Cc: Gustavo Padovan <gustavo@padovan.org>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464818821-5736-11-git-send-email-daniel.vetter@ffwll.ch
Mostly this is unexpected indents. But really it's just a
demonstration for my patch, all these issues have been found&fixed
using the correct source file and line number support I just added.
All line numbers have been perfectly accurate.
One issue looked a bit fishy in intel_lrc.c, where I don't quite grok
what sphinx is unhappy about. But since that file looks like it has
never seen a proper kernel-doc parser I figured better to fix in a
separate path.
v2: Use fancy new &drm_device->struct_mutex linking (Jani).
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: linux-doc@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The VBT has these mysterious H/V image sizes as part of the display
timings. Looking at some dumps those appear to be the physical
dimensions in mm. Which makes sense since the timing descriptor matches
the format used by EDID detailed timing descriptor, which defines these
as "H/V Addressable Video Image Size in mm".
So let's use that information from the panel fixed mode to get the
physical dimensions for LVDS/eDP/DSI displays. And with that we can
fill out the display_info so that userspace can get at it via
GetConnector.
v2: Use (hi<<8)|lo instead of broken (hi<<4)+lo
Handle LVDS and eDP too
Cc: Stephen Just <stephenjust@gmail.com>
Tested-by: Stephen Just <stephenjust@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96255
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464685714-30507-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
My old 845g complains that the child_device_size inside its VBT,
version 110, is incorrect. Let's fiddle with the version matching such
that it works with this VBT (i.e. treat BIOS v110 as having the same size
as v108).
Fixes [drm:intel_bios_init] *ERROR* Unexpected child device config
size 27 (expected 33 for VBT version 110)
Whether this is correct, no one knows - but it works for this particular
machine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464800923-6054-1-git-send-email-chris@chris-wilson.co.uk
Git got absolutely destroyed with all our cherry-picking from
drm-intel-next-queued to various branches. It ended up inserting
intel_crtc_page_flip 2x even in intel_display.c.
Backmerge to get back to sanity.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
drm-intel-next-2016-05-22:
- cmd-parser support for direct reg->reg loads (Ken Graunke)
- better handle DP++ smart dongles (Ville)
- bxt guc fw loading support (Nick Hoathe)
- remove a bunch of struct typedefs from dpll code (Ander)
- tons of small work all over to avoid casting between drm_device and the i915
dev struct (Tvrtko&Chris)
- untangle request retiring from other operations, also fixes reset stat corner
cases (Chris)
- skl atomic watermark support from Matt Roper, yay!
- various wm handling bugfixes from Ville
- big pile of cdclck rework for bxt/skl (Ville)
- CABC (Content Adaptive Brigthness Control) for dsi panels (Jani&Deepak M)
- nonblocking atomic commits for plane-only updates (Maarten Lankhorst)
- bunch of PSR fixes&improvements
- untangle our map/pin/sg_iter code a bit (Dave Gordon)
drm-intel-next-2016-05-08:
- refactor stolen quirks to share code between early quirks and i915 (Joonas)
- refactor gem BO/vma funcstion (Tvrtko&Dave)
- backlight over DPCD support (Yetunde Abedisi)
- more dsi panel sequence support (Jani)
- lots of refactoring around handling iomaps, vma, ring access and related
topics culmulating in removing the duplicated request tracking in the execlist
code (Chris & Tvrtko) includes a small patch for core iomapping code
- hw state readout for bxt dsi (Ramalingam C)
- cdclk cleanups (Ville)
- dedupe chv pll code a bit (Ander)
- enable semaphores on gen8+ for legacy submission, to be able to have a direct
comparison against execlist on the same platform (Chris) Not meant to be used
for anything else but performance tuning
- lvds border bit hw state checker fix (Jani)
- rpm vs. shrinker/oom-notifier fixes (Praveen Paneri)
- l3 tuning (Imre)
- revert mst dp audio, it's totally non-functional and crash-y (Lyude)
- first official dmc for kbl (Rodrigo)
- and tons of small things all over as usual
* 'drm-intel-next' of git://anongit.freedesktop.org/drm-intel: (194 commits)
drm/i915: Revert async unpin and nonblocking atomic commit
drm/i915: Update DRIVER_DATE to 20160522
drm/i915: Inline sg_next() for the optimised SGL iterator
drm/i915: Introduce & use new lightweight SGL iterators
drm/i915: optimise i915_gem_object_map() for small objects
drm/i915: refactor i915_gem_object_pin_map()
drm/i915/psr: Implement PSR2 w/a for gen9
drm/i915/psr: Use ->get_aux_send_ctl functions
drm/i915/psr: Order DP aux transactions correctly
drm/i915/psr: Make idle_frames sensible again
drm/i915/psr: Try to program link training times correctly
drm/i915/userptr: Convert to drm_i915_private
drm/i915: Allow nonblocking update of pageflips.
drm/i915: Check for unpin correctness.
Reapply "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
drm/i915: Make unpin async.
drm/i915: Prepare connectors for nonblocking checks.
drm/i915: Pass atomic states to fbc update functions.
drm/i915: Remove reset_counter from intel_crtc.
drm/i915: Remove queue_flip pointer.
...
Frist -misc pull for 4.8, with pretty much just random all over plus a few
more lockless gem BO patches acked/reviewed by driver maintainers.
I'm starting a bit earlier this time around because there's a few invasive
patch series to land (nonblocking atomic prep work, fence prep work,
rst/sphinx kerneldoc finally happening) and I need a baseline with all the
branches merged.
* tag 'topic/drm-misc-2016-06-01' of git://anongit.freedesktop.org/drm-intel: (21 commits)
drm/vc4: Use lockless gem BO free callback
drm/vc4: Use drm_gem_object_unreference_unlocked
drm: Initialize a linear gamma table by default
drm/vgem: Use lockless gem BO free callback
drm/qxl: Don't set a gamma table size
drm/msm: Nuke dummy gamma_set/get functions
drm/cirrus: Drop redundnant gamma size check
drm/fb-helper: Remove dead code in setcolreg
drm/mediatek: Use lockless gem BO free callback
drm/hisilicon: Use lockless gem BO free callback
drm/hlcd: Use lockless gem BO free callback
vga_switcheroo: Support deferred probing of audio clients
vga_switcheroo: Add helper for deferred probing
virtio-gpu: fix output lookup
drm/doc: Unify KMS Locking docs
drm/atomic-helper: Do not call ->mode_fixup for CRTC which will be disabled
Fix annoyingly awkward typo in drm_edid_load.c
drm/doc: Drop vblank_disable_allow wording
drm: use seqlock for vblank time/count
drm/mm: avoid possible null pointer dereference
...
if downscaling is enabled plane data rate increases according to scaling
amount. take scaling amount under consideration while calculating plane
data rate
v2: Address Matt's comments, where data rate was overridden because of
missing else.
v3 (by Matt):
- Add braces to 'else' branch to match kernel coding style
- Adjust final calculation now that skl_plane_downscale_amount()
returns 16.16 fixed point value instead of a decimal fixed point
v4 (by Matt):
- Avoid integer overflow by making sure final multiplication is
treated as 64-bit.
Cc: matthew.d.roper@intel.com
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463695381-21368-1-git-send-email-matthew.d.roper@intel.com
Don't use pipe pixel rate for plane pixel rate. Calculate plane pixel according
to formula
adjusted plane_pixel_rate = adjusted pipe_pixel_rate * downscale ammount
downscale amount = max[1, src_h/dst_h] * max[1, src_w/dst_w]
if 90/270 rotation use rotated width & height
v2: use intel_plane_state->visible instead of (fb == NULL) as per Matt's
comment.
v3 (by Matt):
- Keep downscale amount in 16.16 fixed point rather than converting to
decimal fixed point.
- Store adjusted plane pixel rate in plane state instead of the plane
parameters structure that we no longer use.
v4 (by Matt):
- Significant rebasing onto latest atomic watermark work
- Don't bother storing plane pixel rate in state; just calculate it
right before the calls that make use of it.
- Fix downscale calculations to actually use width values when
computing downscale_w rather than copy/pasted height values.
Cc: matthew.d.roper@intel.com
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463439121-28974-4-git-send-email-matthew.d.roper@intel.com
don't always use 8 ddb as minimum, instead calculate using proper
algorithm.
v2: optimizations as per Matt's comments.
v3 (by Matt):
- Fix boolean logic for !fb test in skl_ddb_min_alloc()
- Adjust negative tiling format comparisons in skl_ddb_min_alloc() to
improve readability.
v4 (by Matt):
- Rebase onto recent atomic watermark changes
- Slight tweaks to code flow to make the logic more closely match the
description in the bspec.
v5 (by Matt):
- Handle minimum scanline calculation properly for 4 & 8 bpp formats.
8bpp isn't actually possible right now, but it's listed in the bspec
so I've included it here for forward compatibility (similar to how
we have logic for NV12).
v6 (by Matt):
- Calculate plane_bpp correctly for non-NV12 formats. (Mahesh)
Cc: matthew.d.roper@intel.com
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464713939-10440-1-git-send-email-matthew.d.roper@intel.com
We don't actually read out full plane state during driver startup (only
whether the primary plane is enabled/disabled), so all of the src/dest
rectangles are invalid at this point. However this calculation was
needless anyway since we re-calculate them from scratch on the very
first atomic transaction after boot anyway.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463439121-28974-2-git-send-email-matthew.d.roper@intel.com
If the VBT says that a certain port should be eDP (and hence fused off
from HDMI), but in reality it isn't, we need to try and acquire the HDMI
connection instead. So only trust the VBT edp setting if we can connect
to an eDP device on that port.
Fixes: d2182a6608 (drm/i915: Don't register HDMI connectors for eDP ports on VLV/CHV)
References: https://bugs.freedesktop.org/show_bug.cgi?id=96288
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Phidias Chiang <phidias.chiang@canonical.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464766070-31623-1-git-send-email-chris@chris-wilson.co.uk
This reverts the following patches:
d55dbd06bb drm/i915: Allow nonblocking update of pageflips.
15c86bdb76 drm/i915: Check for unpin correctness.
95c2ccdc82 Reapply "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
a6747b7304 drm/i915: Make unpin async.
03f476e1fc drm/i915: Prepare connectors for nonblocking checks.
2099deffef drm/i915: Pass atomic states to fbc update functions.
ee7171af72 drm/i915: Remove reset_counter from intel_crtc.
2ee004f7c5 drm/i915: Remove queue_flip pointer.
b8d2afae55 drm/i915: Remove use_mmio_flip kernel parameter.
8dd634d922 drm/i915: Remove cs based page flip support.
143f73b3bf drm/i915: Rework intel_crtc_page_flip to be almost atomic, v3.
84fc494b64 drm/i915: Add the exclusive fence to plane_state.
6885843ae1 drm/i915: Convert flip_work to a list.
aa420ddd8e drm/i915: Allow mmio updates on all platforms, v2.
afee4d8707 Revert "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
"drm/i915: Allow nonblocking update of pageflips" should have been
split up, misses a proper commit message and seems to cause issues in
the legacy page_flip path as demonstrated by kms_flip.
"drm/i915: Make unpin async" doesn't handle the unthrottled cursor
updates correctly, leading to an apparent pin count leak. This is
caught by the WARN_ON in i915_gem_object_do_pin which screams if we
have more than DRM_I915_GEM_OBJECT_MAX_PIN_COUNT pins.
Unfortuantely we can't just revert these two because this patch series
came with a built-in bisect breakage in the form of temporarily
removing the unthrottled cursor update hack for legacy cursor ioctl.
Therefore there's no other option than to revert the entire pile :(
There's one tiny conflict in intel_drv.h due to other patches, nothing
serious.
Normally I'd wait a bit longer with doing a maintainer revert, but
since the minimal set of patches we need to revert (due to the bisect
breakage) is so big, time is running out fast. And very soon
(especially after a few attempts at fixing issues) it'll be really
hard to revert things cleanly.
Lessons learned:
- Not a good idea to rush the review (done by someone fairly new to
the area) and not make sure domain experts had a chance to read it.
- Patches should be properly split up. I only looked at the two
patches that should be reverted in detail, but both look like the
mix up different things in one patch.
- Patches really should have proper commit messages. Especially when
doing more than one thing, and especially when touching critical and
tricky core code.
- Building a patch series and r-b stamping it when it has a built-in
bisect breakage is not a good idea.
- I also think we need to stop building up technical debt by
postponing atomic igt testcases even longer. I think it's clear that
there's enough corner cases in this beast that we really need to
have the testcases _before_ the next step lands.
(cherry picked from commit 5a21b6650a
from drm-intel-next-queeud)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
On Loading, GuC sets PM interrupts routing (bit 31) and clears ARAT
expired interrupt (bit 9). Host turbo also updates this register
in RPS flows. This patch ensures bit 31 and bit 9 setup by GuC persists.
ARAT timer interrupt is needed in GuC for various features. It also
facilitates halting GuC and hence achieving RC6. PM interrupt routing
will not impact RPS interrupt reception by host as GuC will redirect
them.
This patch fixes igt test pm_rc6_residency that was failing with guc
load/submission enabled. Tested with SKL GuC v6.1 and BXT GuC v5.1 and v8.7.
v2: i915_irq/i915_pm decoupling from intel_guc. (ChrisW)
v3: restructuring the mask update and rebase w.r.t Ville's patch. (ChrisW)
v4: Updating the pm_intr_keep during direct_interrupts_to_guc. (Sagar)
Cc: Chris Harris <chris.harris@intel.com>
Cc: Zhe Wang <zhe1.wang@intel.com>
Cc: Deepak S <deepak.s@intel.com>
Cc: Satyanantha, Rama Gopal M <rama.gopal.m.satyanantha@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Testcase: igt/pm_rc6_residency
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Tested-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464683307-19475-1-git-send-email-sagar.a.kamble@intel.com
So far we've got one condition when DRM drivers need to defer probing
on a dual GPU system and it's coded separately into each of the relevant
drivers. As suggested by Daniel Vetter, deduplicate that code in the
drivers and move it to a new vga_switcheroo helper. This yields better
encapsulation of concepts and lets us add further checks in a central
place. (The existing check pertains to pre-retina MacBook Pros and an
additional check is expected to be needed for retinas.)
One might be tempted to check deferred probing conditions in
vga_switcheroo_register_client(), but this is usually called fairly late
during driver load. The GPU is fully brought up and ready for switching
at that point. On boot the ->probe hook is potentially called dozens of
times until it finally succeeds, and each time we'd repeat bringup and
teardown of the GPU, lengthening boot time considerably and cluttering
logfiles. A separate helper is therefore needed which can be called
right at the beginning of the ->probe hook.
Note that amdgpu currently does not call this helper as the AMD GPUs
built into MacBook Pros are only supported by radeon so far.
v2: This helper could eventually be used by audio clients as well,
so rephrase kerneldoc to refer to "client" instead of "GPU"
and move the single existing check in an if block specific
to PCI_CLASS_DISPLAY_VGA devices. Move documentation on
that check from kerneldoc to a comment. (Daniel Vetter)
v3: Mandate in kerneldoc that registration of client shall only
happen after calling this helper. (Daniel Vetter)
v4: Rebase on 412c8f7de0 ("drm/radeon: Return -EPROBE_DEFER when
amdkfd not loaded")
v5: Some Optimus GPUs use PCI_CLASS_DISPLAY_3D, make sure those are
matched as well. (Emil Velikov)
v6: The if-condition referring to PCI_BASE_CLASS_DISPLAY may be
considered a functional change. Move to a separate commit to
keep this a pure refactoring change. (Emil Velikov, Jani Nikula)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/575885fd440c2b13c3f19ddf44360cfbbff35f50.1464685538.git.lukas@wunner.de
Rather than let the core generate usless encoder names, let's pass in
something that actually identifies the piece of hardware we're dealing
with.
v2: Use 'DSI %c' instead of 'MIPI %c' for DSI encoders (Jani)
v3: Use port_name() in DSI code since we have it
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-7-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Let's name our planes in a way that makes sense wrt. the spec:
- skl+ -> "plane 1A", "plane 2A", "plane 1C", "cursor A" etc.
- g4x+ -> "primary A", "primary B", "sprite A", "cursor C" etc.
- pre-g4x -> "plane A", "cursor B" etc.
v2: Rebase on top of the fixed/cleaned error paths
Use a local 'name' variable to make things easier
v3: Pass the name as a function argument to drm_universal_plane_init() (Jani)
v3: Pass the printf style string to drm_universal_plane_init()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Call intel_plane_destroy() instead of drm_plane_cleanup() so that we
also free the plane struct itself when bailing out of the crtc init.
And make intel_plane_destroy() NULL tolerant to avoid having to check
for it in the caller.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
v2: Fix intel_crtc leak on failure to allocate the name
Use a local 'name' variable to make things easier
v3: Pass the name as a function arguemnt to drm_crtc_init_with_planes() (Jani)
v4: Pass the printf style format string to drm_crtc_init_with_planes()
v5: Drop spurious code changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Pull drm fixes from Dave Airlie:
- one IMX built-in regression fix
- a set of amdgpu fixes, mostly powerplay and polaris GPU stuff
- a set of i915 fixes all over, many cc'ed to stable.
The i915 batch contain support for DP++ dongle detection, which is
used to fix some regressions in the HDMI color depth area
* tag 'drm-fixes-v4.7-rc1' of git://people.freedesktop.org/~airlied/linux: (44 commits)
drm/amd: add Kconfig dependency for ACP on DRM_AMDGPU
drm/amdgpu: Fix hdmi deep color support.
drm/amdgpu: fix bug in fence driver fini
drm/i915: Stop automatically retiring requests after a GPU hang
drm/i915: Unify intel_ring_begin()
drm/i915: Ignore stale wm register values on resume on ilk-bdw (v2)
drm/i915/psr: Try to program link training times correctly
drm/imx: Match imx-ipuv3-crtc components using device node in platform data
drm/i915/bxt: Adjusting the error in horizontal timings retrieval
drm/i915: Don't leave old junk in ilk active watermarks on readout
drm/i915: s/DPPL/DPLL/ for SKL DPLLs
drm/i915: Fix gen8 semaphores id for legacy mode
drm/i915: Set crtc_state->lane_count for HDMI
drm/i915/BXT: Retrieving the horizontal timing for DSI
drm/i915: Protect gen7 irq_seqno_barrier with uncore lock
drm/i915: Re-enable GGTT earlier during resume on pre-gen6 platforms
drm/i915: Determine DP++ type 1 DVI adaptor presence based on VBT
drm/i915: Enable/disable TMDS output buffers in DP++ adaptor as needed
drm/i915: Respect DP++ adaptor TMDS clock limit
drm: Add helper for DP++ adaptors
...
Reject the modeset if the requested dotclock exceeds the maximum allowed
by the hardware. So far we've only checked this on gen2/3 while also
handling the double wide vs. single wide pipe selection. Extend the
check to all platforms since we have the max dotclock correctly
populated now across the board.
Testcase: igt/kms_invalid_dotclock
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464114859-15610-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
I see the main drm pull got merged, here's the first batch of fixes for
4.7 already. Fixes all around, a large portion cc: stable stuff.
[airlied: the DP++ stuff is a regression fix].
* tag 'drm-intel-next-fixes-2016-05-25' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Stop automatically retiring requests after a GPU hang
drm/i915: Unify intel_ring_begin()
drm/i915: Ignore stale wm register values on resume on ilk-bdw (v2)
drm/i915/psr: Try to program link training times correctly
drm/i915/bxt: Adjusting the error in horizontal timings retrieval
drm/i915: Don't leave old junk in ilk active watermarks on readout
drm/i915: s/DPPL/DPLL/ for SKL DPLLs
drm/i915: Fix gen8 semaphores id for legacy mode
drm/i915: Set crtc_state->lane_count for HDMI
drm/i915/BXT: Retrieving the horizontal timing for DSI
drm/i915: Protect gen7 irq_seqno_barrier with uncore lock
drm/i915: Re-enable GGTT earlier during resume on pre-gen6 platforms
drm/i915: Determine DP++ type 1 DVI adaptor presence based on VBT
drm/i915: Enable/disable TMDS output buffers in DP++ adaptor as needed
drm/i915: Respect DP++ adaptor TMDS clock limit
drm: Add helper for DP++ adaptors
Thanks to Ville Syrjälä for pointing me towards the cause of this issue.
Unfortunately one of the sideaffects of having the refclk for a DPLL set
to SSC is that as long as it's set to SSC, the GPU will prevent us from
powering down any of the pipes or transcoders using it. A couple of
BIOSes enable SSC in both PCH_DREF_CONTROL and in the DPLL
configurations. This causes issues on the first modeset, since we don't
expect SSC to be left on and as a result, can't successfully power down
the pipes or the transcoders using it. Here's an example from this Dell
OptiPlex 990:
[drm:intel_modeset_init] SSC enabled by BIOS, overriding VBT which says disabled
[drm:intel_modeset_init] 2 display pipes available.
[drm:intel_update_cdclk] Current CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max dotclock rate: 360000 kHz
vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[drm:intel_crt_reset] crt adpa set to 0xf40000
[drm:intel_dp_init_connector] Adding DP connector on port C
[drm:intel_dp_aux_init] registering DPDDC-C bus for card0-DP-1
[drm:ironlake_init_pch_refclk] has_panel 0 has_lvds 0 has_ck505 0
[drm:ironlake_init_pch_refclk] Disabling SSC entirely
… later we try committing the first modeset …
[drm:intel_dump_pipe_config] [CRTC:26][modeset] config ffff88041b02e800 for pipe A
[drm:intel_dump_pipe_config] cpu_transcoder: A
…
[drm:intel_dump_pipe_config] dpll_hw_state: dpll: 0xc4016001, dpll_md: 0x0, fp0: 0x20e08, fp1: 0x30d07
[drm:intel_dump_pipe_config] planes on this crtc
[drm:intel_dump_pipe_config] STANDARD PLANE:23 plane: 0.0 idx: 0 enabled
[drm:intel_dump_pipe_config] FB:42, fb = 800x600 format = 0x34325258
[drm:intel_dump_pipe_config] scaler:0 src (0, 0) 800x600 dst (0, 0) 800x600
[drm:intel_dump_pipe_config] CURSOR PLANE:25 plane: 0.1 idx: 1 disabled, scaler_id = 0
[drm:intel_dump_pipe_config] STANDARD PLANE:27 plane: 0.1 idx: 2 disabled, scaler_id = 0
[drm:intel_get_shared_dpll] CRTC:26 allocated PCH DPLL A
[drm:intel_get_shared_dpll] using PCH DPLL A for pipe A
[drm:ilk_audio_codec_disable] Disable audio codec on port C, pipe A
[drm:intel_disable_pipe] disabling pipe A
------------[ cut here ]------------
WARNING: CPU: 1 PID: 130 at drivers/gpu/drm/i915/intel_display.c:1146 intel_disable_pipe+0x297/0x2d0 [i915]
pipe_off wait timed out
…
---[ end trace 94fc8aa03ae139e8 ]---
[drm:intel_dp_link_down]
[drm:ironlake_crtc_disable [i915]] *ERROR* failed to disable transcoder A
Later modesets succeed since they reset the DPLL's configuration anyway,
but this is enough to get stuck with a big fat warning in dmesg.
A better solution would be to add refcounts for the SSC source, but for
now leaving the source clock on should suffice.
Changes since v3:
- Move temp variable into loop
- Move checks for using_ssc_source to after we've figured out has_ck505
- Add using_ssc_source to debug output
Changes since v2:
- Fix debug output for when we disable the CPU source
Changes since v1:
- Leave the SSC source clock on instead of just shutting it off on all
of the DPLL configurations.
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1464199863-9397-1-git-send-email-cpaul@redhat.com
This set of changes introduces an atomic API to the PWM subsystem. This
is influenced by the DRM atomic API that was introduced a while back,
though it is obviously a lot simpler. The fundamental idea remains the
same, though: drivers provide a single callback to implement the atomic
configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware. Many
use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are postponed
to v4.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sxT9
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes introduces an atomic API to the PWM subsystem.
This is influenced by the DRM atomic API that was introduced a while
back, though it is obviously a lot simpler. The fundamental idea
remains the same, though: drivers provide a single callback to
implement the atomic configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware.
Many use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are
postponed to v4.8"
* tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
pwm: Add information about polarity, duty cycle and period to debugfs
pwm: Switch to the atomic API
pwm: Update documentation
pwm: Add core infrastructure to allow atomic updates
pwm: Add hardware readout infrastructure
pwm: Move the enabled/disabled info into pwm_state
pwm: Introduce the pwm_state concept
pwm: Keep PWM state in sync with hardware state
ARM: Explicitly apply PWM config extracted from pwm_args
drm: i915: Explicitly apply PWM config extracted from pwm_args
input: misc: pwm-beeper: Explicitly apply PWM config extracted from pwm_args
input: misc: max8997: Explicitly apply PWM config extracted from pwm_args
backlight: lm3630a: explicitly apply PWM config extracted from pwm_args
backlight: lp855x: Explicitly apply PWM config extracted from pwm_args
backlight: lp8788: Explicitly apply PWM config extracted from pwm_args
backlight: pwm_bl: Use pwm_get_args() where appropriate
fbdev: ssd1307fb: Use pwm_get_args() where appropriate
regulator: pwm: Use pwm_get_args() where appropriate
leds: pwm: Use pwm_get_args() where appropriate
input: misc: max77693: Use pwm_get_args() where appropriate
...
I noticed that during S4 resume BIOS incorrectly sets bits 18, 19 which
are reserved/MBZ and sets the decimal frequency fields to all 0xff in
the CDCLK register. The result is a hard lockup as display register
accesses are attempted later. Work around this by sanitizing the CDCLK
PLL/dividers the same way it's done on SKL.
While this is clearly a BIOS bug which should be fixed separately, it
doesn't hurt to check/sanitize this regardless.
v2:
- Use the same condition for VCO and CDCLK in broxton_init_cdclk as is
used in skl_init_cdclk for the same purpose.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464093513-16258-2-git-send-email-imre.deak@intel.com
If the CDCLK PLL isn't locked or incorrectly configured we can just
assume that it's off resulting in fully re-initializing both CDCLK PLL
and CDCLK dividers. This way the CDCLK PLL sanitization added in the
following patch can be done on BXT the same way as it's done on SKL.
v2: (Ville)
- Remove the remaining PLL specific checks from skl_sanitize_cdclk() and
depend instead on the corresponding check in skl_dpll0_update().
- Use vco == 0 instead of the corresponding boolean check in
skl_sanitize_cdclk().
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464093513-16258-1-git-send-email-imre.deak@intel.com
This reverts the following patches:
d55dbd06bb drm/i915: Allow nonblocking update of pageflips.
15c86bdb76 drm/i915: Check for unpin correctness.
95c2ccdc82 Reapply "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
a6747b7304 drm/i915: Make unpin async.
03f476e1fc drm/i915: Prepare connectors for nonblocking checks.
2099deffef drm/i915: Pass atomic states to fbc update functions.
ee7171af72 drm/i915: Remove reset_counter from intel_crtc.
2ee004f7c5 drm/i915: Remove queue_flip pointer.
b8d2afae55 drm/i915: Remove use_mmio_flip kernel parameter.
8dd634d922 drm/i915: Remove cs based page flip support.
143f73b3bf drm/i915: Rework intel_crtc_page_flip to be almost atomic, v3.
84fc494b64 drm/i915: Add the exclusive fence to plane_state.
6885843ae1 drm/i915: Convert flip_work to a list.
aa420ddd8e drm/i915: Allow mmio updates on all platforms, v2.
afee4d8707 Revert "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
"drm/i915: Allow nonblocking update of pageflips" should have been
split up, misses a proper commit message and seems to cause issues in
the legacy page_flip path as demonstrated by kms_flip.
"drm/i915: Make unpin async" doesn't handle the unthrottled cursor
updates correctly, leading to an apparent pin count leak. This is
caught by the WARN_ON in i915_gem_object_do_pin which screams if we
have more than DRM_I915_GEM_OBJECT_MAX_PIN_COUNT pins.
Unfortuantely we can't just revert these two because this patch series
came with a built-in bisect breakage in the form of temporarily
removing the unthrottled cursor update hack for legacy cursor ioctl.
Therefore there's no other option than to revert the entire pile :(
There's one tiny conflict in intel_drv.h due to other patches, nothing
serious.
Normally I'd wait a bit longer with doing a maintainer revert, but
since the minimal set of patches we need to revert (due to the bisect
breakage) is so big, time is running out fast. And very soon
(especially after a few attempts at fixing issues) it'll be really
hard to revert things cleanly.
Lessons learned:
- Not a good idea to rush the review (done by someone fairly new to
the area) and not make sure domain experts had a chance to read it.
- Patches should be properly split up. I only looked at the two
patches that should be reverted in detail, but both look like the
mix up different things in one patch.
- Patches really should have proper commit messages. Especially when
doing more than one thing, and especially when touching critical and
tricky core code.
- Building a patch series and r-b stamping it when it has a built-in
bisect breakage is not a good idea.
- I also think we need to stop building up technical debt by
postponing atomic igt testcases even longer. I think it's clear that
there's enough corner cases in this beast that we really need to
have the testcases _before_ the next step lands.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
One of the uses for i915_gem_objects is pin-pointing leaks. For this, we
can compare the number of allocated objects and who owns them, a
discrepancy here often indicates a kernel bug. One allocator of unreported
objects is for backing context objects, so include those in the listing.
v2: Take filelist_mutex which requires a little dance with struct_mutex
to avoid nesting filelist_mutex inside struct_mutex.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-10-git-send-email-chris@chris-wilson.co.uk
struct intel_context contains two substructs, one for the legacy RCS and
one for every execlists engine. Since legacy RCS is a subset of the
execlists engine support, just combine the two substructs.
v2: Only pin the default context for legacy mode (the object only exists
for legacy, but adding i915.enable_execlists provides symmetry with the
cleanup functions).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-8-git-send-email-chris@chris-wilson.co.uk
Just move the kernel_context member of drm_i915_private next to the
engines it is associated with.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-7-git-send-email-chris@chris-wilson.co.uk
Print the context's owner (via the pid under file_priv) under debugfs.
In doing so, we must be careful that the filp is not accessed after it
is freed (notified via i915_gem_context_close).
v2: Mark the file_priv as closed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-6-git-send-email-chris@chris-wilson.co.uk
Rather than have every context ask "am I owned by the kernel? pin!",
move that logic into the creator of the kernel context, in order to
improve code comprehension.
v2: Throw away the user_handle on failure to allocate the ppgtt.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-5-git-send-email-chris@chris-wilson.co.uk
We want to give a name to the currently anonymous per-engine struct
inside the context, so that we can assign it to a local variable and
save clumsy typing. The name we have chosen is intel_context as it
reflects the HW facing portion of the context state (the logical context
state, the registers, the ringbuffer etc).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-4-git-send-email-chris@chris-wilson.co.uk
i915_gem_context_get() is a very simple wrapper around idr_find(), so
simple that it would be smaller to do the lookup inline. Also we use the
verb 'lookup' to return a pointer from a handle, freeing 'get' to imply
obtaining a reference to the context.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-3-git-send-email-chris@chris-wilson.co.uk
Our goal is to rename the anonymous per-engine struct beneath the
current intel_context. However, after a lively debate resolving around
the confusion between intel_context_engine and intel_engine_context, the
realisation is that the two structs target different users. The outer
struct is API / user facing, and so carries the higher level GEM
information. The inner struct is hw facing. Thus we want to name the
inner struct intel_context and the outer one i915_gem_context. As the
first step, we need to rename the current struct:
s/struct intel_context/struct i915_gem_context/
which fits much better with its constructors already conveying the
i915_gem_context prefix!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-1-git-send-email-chris@chris-wilson.co.uk
New GuC code is logging errors at runtime suspend and resume which
causes CI testing to log "orange" status. Default to not trying to
load the firmware until this is resolved.
Example of the log:
[drm] RC6 on
[drm:intel_runtime_suspend] Suspending device
[drm:host2guc_action [i915]] *ERROR* GUC: host2guc action 0x501 failed. ret=-110 status=0x00000501 response=0x40000000
...
[drm:intel_runtime_resume] Resuming device
[drm:host2guc_action [i915]] *ERROR* GUC: host2guc action 0x502 failed. ret=-110 status=0x00000502 response=0x40000000
[drm:intel_runtime_resume] Device resumed
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Harris <chris.harris@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1464017675-12257-1-git-send-email-tvrtko.ursulin@linux.intel.com
Merge yet more updates from Andrew Morton:
- Oleg's "wait/ptrace: assume __WALL if the child is traced". It's a
kernel-based workaround for existing userspace issues.
- A few hotfixes
- befs cleanups
- nilfs2 updates
- sys_wait() changes
- kexec updates
- kdump
- scripts/gdb updates
- the last of the MM queue
- a few other misc things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (84 commits)
kgdb: depends on VT
drm/amdgpu: make amdgpu_mn_get wait for mmap_sem killable
drm/radeon: make radeon_mn_get wait for mmap_sem killable
drm/i915: make i915_gem_mmap_ioctl wait for mmap_sem killable
uprobes: wait for mmap_sem for write killable
prctl: make PR_SET_THP_DISABLE wait for mmap_sem killable
exec: make exec path waiting for mmap_sem killable
aio: make aio_setup_ring killable
coredump: make coredump_wait wait for mmap_sem for write killable
vdso: make arch_setup_additional_pages wait for mmap_sem for write killable
ipc, shm: make shmem attach/detach wait for mmap_sem killable
mm, fork: make dup_mmap wait for mmap_sem for write killable
mm, proc: make clear_refs killable
mm: make vm_brk killable
mm, elf: handle vm_brk error
mm, aout: handle vm_brk failures
mm: make vm_munmap killable
mm: make vm_mmap killable
mm: make mmap_sem for write waits killable for mm syscalls
MAINTAINERS: add co-maintainer for scripts/gdb
...
i915_gem_mmap_ioctl relies on mmap_sem for write. If the waiting task
gets killed by the oom killer it would block oom_reaper from
asynchronous address space reclaim and reduce the chances of timely OOM
resolving. Wait for the lock in the killable mode and return with EINTR
if the task got killed while waiting.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull drm updates from Dave Airlie:
"Here's the main drm pull request for 4.7, it's been a busy one, and
I've been a bit more distracted in real life this merge window. Lots
more ARM drivers, not sure if it'll ever end. I think I've at least
one more coming the next merge window.
But changes are all over the place, support for AMD Polaris GPUs is in
here, some missing GM108 support for nouveau (found in some Lenovos),
a bunch of MST and skylake fixes.
I've also noticed a few fixes from Arnd in my inbox, that I'll try and
get in asap, but I didn't think they should hold this up.
New drivers:
- Hisilicon kirin display driver
- Mediatek MT8173 display driver
- ARC PGU - bitstreamer on Synopsys ARC SDP boards
- Allwinner A13 initial RGB output driver
- Analogix driver for DisplayPort IP found in exynos and rockchip
DRM Core:
- UAPI headers fixes and C++ safety
- DRM connector reference counting
- DisplayID mode parsing for Dell 5K monitors
- Removal of struct_mutex from drivers
- Connector registration cleanups
- MST robustness fixes
- MAINTAINERS updates
- Lockless GEM object freeing
- Generic fbdev deferred IO support
panel:
- Support for a bunch of new panels
i915:
- VBT refactoring
- PLL computation cleanups
- DSI support for BXT
- Color manager support
- More atomic patches
- GEM improvements
- GuC fw loading fixes
- DP detection fixes
- SKL GPU hang fixes
- Lots of BXT fixes
radeon/amdgpu:
- Initial Polaris support
- GPUVM/Scheduler/Clock/Power improvements
- ASYNC pageflip support
- New mesa feature support
nouveau:
- GM108 support
- Power sensor support improvements
- GR init + ucode fixes.
- Use GPU provided topology information
vmwgfx:
- Add host messaging support
gma500:
- Some cleanups and fixes
atmel:
- Bridge support
- Async atomic commit support
fsl-dcu:
- Timing controller for LCD support
- Pixel clock polarity support
rcar-du:
- Misc fixes
exynos:
- Pipeline clock support
- Exynoss4533 SoC support
- HW trigger mode support
- export HDMI_PHY clock
- DECON5433 fixes
- Use generic prime functions
- use DMA mapping APIs
rockchip:
- Lots of little fixes
vc4:
- Render node support
- Gamma ramp support
- DPI output support
msm:
- Mostly cleanups and fixes
- Conversion to generic struct fence
etnaviv:
- Fix for prime buffer handling
- Allow hangcheck to be coalesced with other wakeups
tegra:
- Gamme table size fix"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1050 commits)
drm/edid: add displayid detailed 1 timings to the modelist. (v1.1)
drm/edid: move displayid validation to it's own function.
drm/displayid: Iterate over all DisplayID blocks
drm/edid: move displayid tiled block parsing into separate function.
drm: Nuke ->vblank_disable_allowed
drm/vmwgfx: Report vmwgfx version to vmware.log
drm/vmwgfx: Add VMWare host messaging capability
drm/vmwgfx: Kill some lockdep warnings
drm/nouveau/gr/gf100-: fix race condition in fecs/gpccs ucode
drm/nouveau/core: recognise GM108 chipsets
drm/nouveau/gr/gm107-: fix touching non-existent ppcs in attrib cb setup
drm/nouveau/gr/gk104-: share implementation of ppc exception init
drm/nouveau/gr/gk104-: move rop_active_fbps init to nonctx
drm/nouveau/bios/pll: check BIT table version before trying to parse it
drm/nouveau/bios/pll: prevent oops when limits table can't be parsed
drm/nouveau/volt/gk104: round up in gk104_volt_set
drm/nouveau/fb/gm200: setup mmu debug buffer registers at init()
drm/nouveau/fb/gk20a,gm20b: setup mmu debug buffer registers at init()
drm/nouveau/fb/gf100-: allocate mmu debug buffers
drm/nouveau/fb: allow chipset-specific actions for oneinit()
...
Like with cdclk, the DMC is supposed to manage dbuf enabling/disabling.
Let's make sure it has correctly restored the dbuf state to enabled
when we disable the DC states.
v2: s/skl/gen9/ in function name (Imre)
Cc: Imre Deak <imre.deak@intel.com>
Suggested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463407180-28993-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
In case the driver is initialized without active displays, we should
just drop the cdclk to the minimum frequency right off the bat. There
might not be a modeset to drop it to the minimum late rafter all.
With DMC supposedly we should always have the cdclk up and running.
The DMC will shut the DE PLL down when appropriate, so let's nuke
the related FIXMEs as well. Trying to do anything different would
go against the expectations of the DMC firmware, and we all know
how fragile the DMC firmware is.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-22-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Rather than having a BXT specific function to make sure the DE PLL is
enabled after disabling DC6, let's just make sure the current cdclk
is the same as what we last programmed.
Having another check in bxt_display_core_init() almost immediately after
the cdclk init seems redundant, so let's just kill that one.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-21-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Make bxt_set_cdclk() more readable by looking at current vs. target
DE PLL vco to determine if the DE PLL needs disabling and/or enabling.
We can also calculate the CD2X divider simply as (vco/cdclk) instead of
depending on magic numbers.
The magic numbers are still needed though, but only to map the supported
cdclk frequencies to corresponding DE PLL frequencies.
Note that w'll now program CDCLK_CTL correctly even for the bypass case.
Actually the CD2X divider should not matter in that case since the
hardware will bypass it too, but the "decimal" part should matter (if we
want to do gmbus/aux with the bypass enabled).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-20-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
We'll want to store the cdclk PLL (whatever PLL that is in reality) vco
frequency somewhere on other platforms too, so let's rename the
skl_vco_freq to cdclk_pll.vco, and let's store it in kHz instead of MHz
to match most of the other clocks.
v2: Drop the spurious > vs != change (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-14-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The SKL 308.57 MHz cdclk is probably 8640/28 = ~308.571 Mhz.
Similartly the 617.14 MHz cdclk is probably 8640/14 = ~617.143 MHz.
Let's use the slightly more accurate numbers. Potentially we might
change to computing all of these based on dividers, but let's
stick to the current theme for now..
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-13-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
SKL and BXT have the same snippets of code for enabling disabling the
DBUF. Extract those into helpers and move the calls from
init/unit_cdclk() to the display core init/init since this stuff isn't
really about cdclk. Also doing the enable twice shouldn't hurt since
you're just setting the request bit again when it was already set.
We can also toss in a few WARNs about the register values into
skl_get_dpll0_vco() now that we know that things should always be
sane there.
Flatten skl_init_cdclk() while at it.
v2: s/skl/gen9/ in function names (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-12-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Currently we initialize cdclk on SKL from two different places,
depending on whether it's during driver init or resume. Let's
unify it to happen from the same place always, and that place will be
the display core init function.
To do this we first run through the cdclk sanitation code, which will
first verify that the PLL is programmed correctly, after which we can
read out the current cdclk frequency, and once the cdclk is known we
verify that the cdclk "decimal" frequency is programmed correctly. If
any of these fail we will force a cdclk change, and to be safe we also
force the PLL to be turned off and on again. If the sanitation step
didn't notice anything amiss, we'll skip the cdclk programming which
will prevent cdclk reprogramming when the displays might be active.
We can also toss in a few WARNs about the register values into
skl_update_dpll0() since we now know that the PLL state should
always be sane when that function is called.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-11-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Now that skl_vco_freq tracks the actual DPLL0 vco frequency, we'll need
something that keeps track of which vco frequency we want to use in case
the current vco is 0. This would be important across supend/resume since
we'll disable DPLL0 around those parts.
We'll also update our idea of max cdclk/dotclock when the preferred
vco changes. That could happen if out initial guess was wrong, and
later eDP would force us to change it. One issue here could be that
changing the max dotclock could cause our mode list to change during
next time the displays get probed. But I don't see a good way to avoid
that, except perhaps by allowing either vco frequency to be used as
needed. But the docs suggest that such usage wasn't really inteded.
Also need to make sure we don't update our max_cdclk value before we
have a preferred vco value, which means moving that to happen after
the cdclk sanitation.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
In case we originally guessed wrong which lcpll vco frequency to use,
we will need to shut down the pll and restart it when reprogamming the
cdclk.
This also allows us to track the actual vco frequency in dev_priv
instead of just a guess.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-8-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Currently we're trying to guess which lcpll vco frequency is used
use based on the cdclk. That doesn't work for cdclk==540 since
both vco frequencies can generate a 540 Mhz output. Let's stop
guessing and just read the actual vco frequency from the
hardware.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Shared plls won't get assigned until the .compute_clocks() hook gets
called, which happens from the crtc .atomic_check hook. That's too late
as the cdclk computation has already happened. So let's move the DPLL0
VCO computation into intel_dp_compute_config() so that it's done when
the cdclk computation happens. Also only do it for eDP since we only
pick DPLL0 for eDP.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
WARNING: Using ChromeOS with an eDP panel and a 4K@60 DP monitor connected
to DDI1 the system will hard hang during a cold boot. Occurs when DDI1
is enabled when the cdclk is less then required. DP connected to DDI2
and HPD on either port works correctly.
Set cdclk based on the max required pixel clock based on VCO
selected. Track boot vco instead of boot cdclk.
The vco is now tracked at the atomic level and all CRTCs updated if
the required vco is changed. Not tested with eDP v1.4 panels that
require 8640 vco due to availability.
V1: initial version
V2: add vco tracking in intel_dp_compute_config(), rename
skl_boot_cdclk.
V3: rebase, V2 feedback not possible as encoders are not aware of
atomic.
V4: track target vco is atomic state. modeset all CRTCs if vco changes
V5: rename atomic variable, cleaner if/else logic, use existing vco if
encoder does not return a new vco value. check_patch.pl cleanup
V6: simplify logic in intel_modeset_checks.
V7: reorder an IF for readability and whitespace fix.
V8: use dev_cdclk for tracking new cdclk during atomic
V9: correctly handle vco 8640 when crtcs==0
V10: Clean up if else in crtcs==0
V11: Rebase for new intel_dpll_mgr.c
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
[vsyrjala: rebased due to churn]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-3-git-send-email-ville.syrjala@linux.intel.com
commit 4e5ca60fd3 ("drm/i915: Use ilk_max_pixel_rate() for BXT cdclk calculation")
tried to change BXT to use ilk_max_pixel_rate() to compute the
pipe pixel rate. I failed to notice that there was another place
in the state readout code that needs the same treatment. So let's
change that one too.
Should probably just change things to always compuyte the pipe pixel
rates, instead of just doing on platforms that can change cdclk
dynamically. But for now let's just move BXT fully over to the
side that uses ilk_pipe_pixel_rate().
Cc: Jani Nikula <jani.nikula@intel.com>
Fixes: 4e5ca60fd3 ("drm/i915: Use ilk_max_pixel_rate() for BXT cdclk calculation")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Current intel_opregion_init is called during the driver registration
phase and intel_opregion_fini from the unregistration phase. Rename the
functions so that this is clear from their names. The phases tell us
what we expect the existing hw state to be, e.g. whether interrupts are
still enabled etc.
It should be noted that the opregion init/fini routines are asymmetric
and this is carried across into their new names. Indeed, their new names
make it even clearer that perhaps all is not well in the opregion
suspend/resume sequence (as well in the module unload).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464012490-30961-2-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Prefer passing struct drm_i915_private to internal interfaces as this
saves us having to dance between drm_device and our native struct. The
savings hare are small (only 70 bytes of unrequired dancing), but
progressive!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464012490-30961-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
We've never actually enabled or unmasked the GSE interrupt on BDW+,
even though the interrupt handler was always prepared for it.
Let's enable it and see what happens.
Credit to Mark Kettenis who fixed this in the OpenBSD fork of the
driver. He reports that it fixed the "ACPI _BCM/_BCQ-based
brightness mechanism on a MacBookPro12,1 and a 3rd gen Lenovo X1
Carbon" for them.
Mark says:
"FWIW, this *is* needed if you want ACPI-based backlight control to
work. On Linux you probably don't notice, since "hardware" backlight
control is preferred over "firmware" or "platform" backlight control.
It would help me if this did land in the Linux tree though, as it will
make future imports of the i915 driver into OpenBSD easier."
So even though we don't really need this, let's put it in to help Mark
with future porting efforts. Should be harmless to have it enabled in
any case.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
References: http://lists.freedesktop.org/archives/intel-gfx/2015-December/081799.html
Reported-by: Mark Kettenis <mark.kettenis@xs4all.nl>
Cc: Mark Kettenis <mark.kettenis@xs4all.nl>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463649283-28698-1-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Mostly little optimisations and future-proofing against code breakage.
For instance, if the driver is correctly following the submission
protocol, the "out of space" condition is impossible, so the previous
runtime WARN_ON() is promoted to a GEM_BUG_ON() for a more dramatic
effect in development and less impact in end-user systems.
Similarly we can make alignment checking more stringent and replace
other WARN_ON() conditions that don't relate to the runtime hardware
state with either BUILD_BUG_ON() for compile-time-detectable issues, or
GEM_BUG_ON() for logical "can't happen" errors.
With those changes, we can convert it to void, as suggested by Chris
Wilson, and update the calling code appropriately.
v2:
Note that we're now putting the request seqno in the "fence_id"
field of each GuC-work-item, in case it turns up somewhere useful
(e.g. in a GuC log) [Tvrtko Ursulin].
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Rather than wait to see whether more space becomes available in the GuC
submission workqueue, we can just return -EAGAIN and let the caller try
again in a little while. This gets rid of an uninterruptable sleep in
the polling code :)
We'll also add a counter to the GuC client statistics, to see how often
we find the WQ full.
v2:
Flag the likely() code path (Tvtrko Ursulin).
v4:
Add/update comments about failure counters (Tvtrko Ursulin).
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
The knowledge of how to derive the relevant client from the request
should be localised within i915_guc_submission.c; the LRC code shouldn't
have to know about the internal details of the GuC submission process.
And all the information the GuC code needs should be encapsulated in (or
reachable from) the request.
v2:
GEM_BUG_ON() for bad GuC client (Tvrtko Ursulin).
Add/update kerneldoc explaining check_space/submit protocol
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Split the function of "enable_guc_submission" into two separate
options. The new one ("enable_guc_loading") controls only the
*fetching and loading* of the GuC firmware image. The existing
one is redefined to control only the *use* of the GuC for batch
submission once the firmware is loaded.
In addition, the degree of control has been refined from a simple
bool to an integer key, allowing several options:
-1 (default) whatever the platform default is
0 DISABLE don't load/use the GuC
1 BEST EFFORT try to load/use the GuC, fallback if not available
2 REQUIRE must load/use the GuC, else leave the GPU wedged
The new platform default (as coded here) will be to attempt to
load the GuC iff the device has a GuC that requires firmware,
but not yet to use it for submission. A later patch will change
to enable it if appropriate.
v4:
Changed some error-message levels, mostly ERROR->INFO, per
review comments by Tvrtko Ursulin.
v5:
Dropped one more error message, disabled GuC submission on
hypothetical firmware-free devices [Tvrtko Ursulin].
v6:
Logging tidy by Tvrtko Ursulin:
* Do not log falling back to execlists when wedging the GPU.
* Do not log fw load errors when load was disabled by user.
* Pass down some error code from fw load for log message to
make more sense.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v5)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Tested-by: Fiedorowicz, Lukasz <lukasz.fiedorowicz@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v5)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com> (v6)
For now, anything with a GuC requires uCode loading, and then supports
command submission once loaded. But these are logically distinct from
simply "having a GuC", so we need a separate macro for the latter. Then,
various tests should use this new macro rather than HAS_GUC_UCODE() or
testing enable_guc_submission.
v4:
Added a couple more uses of the new macro.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
The GuC initialisation code could do other things apart from loading
firmware, so here we rename the three primary entry points to remove any
specific reference to "ucode" (no functional changes, just renaming).
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Following a GPU hang, we break out of the request loop in order to
unlock the struct_mutex for use by the GPU reset. However, if we retire
all the requests at that moment, we cannot identify the guilty request
after performing the reset.
v2: Not automatically retiring requests forces us to recheck for
available ringspace.
Fixes: f4457ae71f ("drm/i915: Prevent leaking of -EIO from i915_wait_request()")
Testcase: igt/gem_reset_stats/ban-*
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Tested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463137042-9669-4-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit e075a32f51)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Combine the near identical implementations of intel_logical_ring_begin()
and intel_ring_begin() - the only difference is that the logical wait
has to check for a matching ring (which is assumed by legacy).
In the process some debug messages are culled as there were following a
WARN if we hit an actual error.
v2: Updated commentary
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461833819-3991-12-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit 987046ad65)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When we resume the watermark register may contain some BIOS leftovers,
or just the hardware reset values. We should ignore those as the
pipes will be off anyway, and so frobbing around with intermediate
watermarks doesn't make much sense.
In fact I think we should just throw the skip_intermediate_wm flag
out, and instead properly sanitize the "active" watermarks to match
the current plane and pipe states. The actual wm state readout might
also need a bit of work. But for now, let's continue with the
skip_intermediate_wm to keep the fix more minimal.
Fixes this sort of errors on resume
[drm:ilk_validate_pipe_wm] LP0 watermark invalid
[drm:intel_crtc_atomic_check] No valid intermediate pipe watermarks are possible
[drm:intel_display_resume [i915]] *ERROR* Restoring old state failed with -22
and a boatload of subsequent modeset BAT fails on my ILK.
v2:
- Rebase; the SKL atomic WM patches that just landed changed the WM
structure fields in intel_crtc_state slightly. (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: ed4a6a7ca8 ("drm/i915: Add two-stage ILK-style watermark programming (v11)")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463159442-20478-1-git-send-email-matthew.d.roper@intel.com
(cherry picked from commit e3d5457c7c)
[Jani: rebase on drm-next while cherry-picking]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The default of 0 is 500us of link training, but that's not enough for
some platforms. Decoding this correctly means we're using 2.5ms of
link training on these platforms, which fixes flickering issues
associated with enabling PSR.
v2: Unbotch the math a bit.
v3: Drop debug hunk.
v4: Improve commit message.
Tested-by: Lyude <cpaul@redhat.com>
Cc: Lyude <cpaul@redhat.com>
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95176
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: fritsch@kodi.tv
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463590036-17824-2-git-send-email-daniel.vetter@ffwll.ch
(cherry picked from commit 50db139018)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In BXT DSI there is no regs programmed with few horizontal timings
in Pixels but txbyteclkhs.. So retrieval process adds some
ROUND_UP ERRORS in the process of PIXELS<==>txbyteclkhs.
Actually here for the given adjusted_mode, we are calculating the
value programmed to the port and then back to the horizontal timing
param in pixels. This is the expected value at the end of get_config,
including roundup errors. And if that is same as retrieved value
from port, then retrieved (HW state) adjusted_mode's horizontal
timings are corrected to match with SW state to nullify the errors.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461053894-5058-2-git-send-email-ramalingam.c@intel.com
(cherry picked from commit 042ab0c3c4)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When we read out the watermark state from the hardware we're supposed to
transfer that into the active watermarks, but currently we fail to any
part of the active watermarks that isn't explicitly written. Let's clear
it all upfront.
Looks like this has been like this since the beginning, when I added the
readout. No idea why I didn't clear it up.
Cc: Matt Roper <matthew.d.roper@intel.com>
Fixes: 243e6a44b9 ("drm/i915: Init HSW watermark tracking in intel_modeset_setup_hw_state()")
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463151318-14719-2-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit 15606534bf)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
With the introduction of a distinct engine->id vs the hardware id, we need
to fix up the value we use for selecting the target engine when signaling
a semaphore. Note that these values can be merged with engine->guc_id.
Fixes: de1add3605
Cc: stable@vger.kernel.org # v4.6
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461932305-14637-3-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit 215a7e3210)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Set the lane count for HDMI to 4. This will make it easier to
unduplicate CHV phy code.
This also fixes the the soft reset programming for HDMI with CHV. After
commit a8f327fb84 ("drm/i915: Clean up CHV lane soft reset
programming"), it wouldn't set the right bits for PCS23 since it relied
on a lane count that was never set.
v2: Set lane_count in *_get_config() to please state checker. (0day)
v3: Set lane_count for DDI in DVI mode too. (CI)
v4: Add note about CHV soft lane reset. (Ander)
Fixes: a8f327fb84 ("drm/i915: Clean up CHV lane soft reset programming")
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461761065-21195-2-git-send-email-ander.conselvan.de.oliveira@intel.com
(cherry picked from commit d4d6279abe)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Faced with sporadic machine hangs on gen7, that mimic the issue of
concurrent writes to the same cacheline and seem to start with
commit 9b9ed30936 (drm/i915: Remove forcewake dance from seqno/irq
barrier on legacy gen6+), let us restore the spinlock around the mmio
read.
Fixes: 9b9ed30936 (drm/i915: Remove forcewake dance from seqno/irq...)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461744121-27051-1-git-send-email-chris@chris-wilson.co.uk
Tested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
(cherry picked from commit bcbdb6d011)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Move the intel_enable_gtt() call to happen before we touch the GTT
during resume. Right now it's done way too late. Before
commit ebb7c78d35 ("agp/intel-gtt: Only register fake agp driver for gen1")
it was actually done earlier on account of also getting called from
the resume hook of the fake agp driver. With the fake agp driver
no longer getting registered we must move the call up.
The symptoms I've seen on my 830 machine include lowmem corruption,
other kinds of memory corruption, and straight up hung machine during
or just after resume. Not really sure what causes the memory corruption,
but so far I've not seen any with this fix.
I think we shouldn't really need to call this during init, but we have
been doing that so I've decided to keep the call. However moving that
call earlier could be prudent as well. Doing it right after the
intel-gtt probe seems appropriate.
Also tested this on 946gz,elk,ilk and all seemed quite happy with
this change.
v2: Reorder init_hw vs. enable_hw functions (Chris)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: ebb7c78d35 ("agp/intel-gtt: Only register fake agp driver for gen1")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462559755-353-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit ac840ae535)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
DP dual mode type 1 DVI adaptors aren't required to implement any
registers, so it's a bit hard to detect them. The best way would
be to check the state of the CONFIG1 pin, but we have no way to
do that. So as a last resort, check the VBT to see if the HDMI
port is in fact a dual mode capable DP port.
v2: Deal with VBT code reorganization
Deal with DRM_DP_DUAL_MODE_UNKNOWN
Reduce DEVICE_TYPE_DP_DUAL_MODE_BITS a bit
Accept both DP and HDMI dvo_port in VBT as my BSW
at least declare its DP port as HDMI :(
v3: Ignore DEVICE_TYPE_NOT_HDMI_OUTPUT (Shashank)
Cc: stable@vger.kernel.org
Cc: Tore Anderson <tore@fud.no>
Reported-by: Tore Anderson <tore@fud.no>
Fixes: 7a0baa6234 ("Revert "drm/i915: Disable 12bpc hdmi for now"")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462362322-31278-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit d61992565b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
To save a bit of power, let's try to turn off the TMDS output buffers
in DP++ adaptors when we're not driving the port.
v2: Let's not forget DDI, toss in a debug message while at it
v3: Just do the TMDS output control based on adaptor type. With the
helper getting passed the type, we wouldn't actually have to
check at all in the driver, but the check eliminates the debug
output more honest
Cc: stable@vger.kernel.org
Cc: Tore Anderson <tore@fud.no>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462216105-20881-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit b2ccb822d3)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Try to detect the max TMDS clock limit for the DP++ adaptor (if any)
and take it into account when checking the port clock.
Note that as with the sink (HDMI vs. DVI) TMDS clock limit we'll ignore
the adaptor TMDS clock limit in the modeset path, in case users are
already "overclocking" their TMDS links. One subtle change here is that
we'll have to respect the adaptor TMDS clock limit when we decide whether
to do 12bpc or 8bpc, otherwise we might end up picking 12bpc and
accidentally driving the TMDS link out of spec even when the user chose
a mode that fits wihting the limits at 8bpc. This means you can't
"overclock" your DP++ dongle at 12bpc anymore, but you can continue to
do so at 8bpc.
Note that for simplicity we'll use the I2C access method for all dual
mode adaptors including type 2. Otherwise we'd have to start mixing
DP AUX and HDMI together. In the future we may need to do that if we
come across any board designs that don't hook up the DDC pins to the
DP++ connectors. Such boards would obviously only work with type 2
dual mode adaptors, and not type 1.
v2: Store adaptor type under indel_hdmi->dp_dual_mode
Deal with DRM_DP_DUAL_MODE_UNKNOWN
Pass adaptor type to drm_dp_dual_mode_max_tmds_clock(),
and use it for type1 adaptors as well
Cc: stable@vger.kernel.org
Reported-by: Tore Anderson <tore@fud.no>
Fixes: 7a0baa6234 ("Revert "drm/i915: Disable 12bpc hdmi for now"")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462216105-20881-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit b1ba124d8e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
I'm looking at trying to possibly merge the 32-bit and 64-bit versions
of the x86 uaccess.h implementation, but first this needs to be cleaned
up.
For example, the 32-bit version of "__copy_to_user_inatomic()" is mostly
the special cases for the constant size, and it's actually never
relevant. Every user except for one aren't actually using a constant
size anyway, and the one user that uses it is better off just using
__put_user() instead.
So get rid of the unnecessary complexity.
[ The same cleanup should likely happen to __copy_from_user_inatomic()
as well, but that one has a lot more users that I need to take a look
at first ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's the big staging and iio driver update for 4.7-rc1.
I think we almost broke even with this release, only adding a few more
lines than we removed, which isn't bad overall given that there's a
bunch of new iio drivers added. The Lustre developers seem to have
woken up from their sleep and have been doing a great job in cleaning up
the code and pruning unused or old cruft, the filesystem is almost
readable :)
Other than that, just a lot of basic coding style cleanups in the churn.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/00QACgkQMUfUDdst+ynXYQCdG9oEsw4CCItbjGfQau5YVGbd
TOcAnA19tZz+Wcg3sLT8Zsm979dgVvDt
=9UG/
-----END PGP SIGNATURE-----
Merge tag 'staging-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver updates from Greg KH:
"Here's the big staging and iio driver update for 4.7-rc1.
I think we almost broke even with this release, only adding a few more
lines than we removed, which isn't bad overall given that there's a
bunch of new iio drivers added.
The Lustre developers seem to have woken up from their sleep and have
been doing a great job in cleaning up the code and pruning unused or
old cruft, the filesystem is almost readable :)
Other than that, just a lot of basic coding style cleanups in the
churn. All have been in linux-next for a while with no reported
issues"
* tag 'staging-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (938 commits)
Staging: emxx_udc: emxx_udc: fixed coding style issue
staging/gdm724x: fix "alignment should match open parenthesis" issues
staging/gdm724x: Fix avoid CamelCase
staging: unisys: rename misleading var ii with frag
staging: unisys: visorhba: switch success handling to error handling
staging: unisys: visorhba: main path needs to flow down the left margin
staging: unisys: visorinput: handle_locking_key() simplifications
staging: unisys: visorhba: fail gracefully for thread creation failures
staging: unisys: visornic: comment restructuring and removing bad diction
staging: unisys: fix format string %Lx to %llx for u64
staging: unisys: remove unused struct members
staging: unisys: visorchannel: correct variable misspelling
staging: unisys: visorhba: replace functionlike macro with function
staging: dgnc: Need to check for NULL of ch
staging: dgnc: remove redundant condition check
staging: dgnc: fix 'line over 80 characters'
staging: dgnc: clean up the dgnc_get_modem_info()
staging: lustre: lnet: enable configuration per NI interface
staging: lustre: o2iblnd: properly set ibr_why
staging: lustre: o2iblnd: remove last of kiblnd_tunables_fini
...
This was added in
commit 0a3e67a4ca
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Sep 30 12:14:26 2008 -0700
drm: Rework vblank-wait handling to allow interrupt reduction.
to stay backwards-compatible with old UMS code that didn't even tell
the kernel when it did a modeset, so that the kernel could
save/restore vblank counters. At worst this means vblanks will be
somewhat funky on a setup that very likely no one still runs.
So let's just nuke it.
Plan B would be to set it unconditionally in drm_vblank_init for kms
drivers, instead of in each driver separately. So if this patch breaks
anything please only restore the hunks in drmP.h and drm_irq.c, plus
add a check for DRIVER_MODESET in drm_vblank_init.
Stumbled over this in a discussion on irc with Chris.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Avoiding the out-of-line call to sg_next() reduces the kernel execution
overhead by 10% in some workloads (for example the Unreal Engine 4 demo
Atlantis on 2GiB GTTs) which are dominated by the cost of inserting PTEs
due to texture thrashing. We can demonstrate this in a microbenchmark
that forces us to rebind the object on every execbuf, where we can
measure a 25% improvement, in the time required to execute an execbuf
requiring a texture to be rebound, for inlining the sg_next() for large
texture sizes.
Benchmark: igt/benchmarks/gem_exec_fault
Benchmark: igt/benchmarks/gem_exec_trace/Atlantis
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1463741647-15666-5-git-send-email-chris@chris-wilson.co.uk
The existing for_each_sg_page() iterator is somewhat heavyweight, and is
limiting i915 driver performance in a few benchmarks. So here we
introduce somewhat lighter weight iterators, primarily for use with GEM
objects or other case where we need only deal with whole aligned pages.
Unlike the old iterator, the new iterators use an internal state
structure which is not intended to be accessed by the caller; instead
each takes as a parameter an output variable which is set before each
iteration. This makes them particularly simple to use :)
One of the new iterators provides the caller with the DMA address of
each page in turn; the other provides the 'struct page' pointer required
by many memory management operations.
Various uses of for_each_sg_page() are then converted to the new macros.
v2: Force inlining of the sg_iter constructor and make the union
anonymous.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1463741647-15666-4-git-send-email-chris@chris-wilson.co.uk
We're using this function for ringbuffers and other "small" objects, so
it's worth avoiding an extra malloc()/free() cycle if the page array is
small enough to put on the stack. Here we've chosen an arbitrary cutoff
of 32 (4k) pages, which is big enough for a ringbuffer (4 pages) or a
context image (currently up to 22 pages).
v5:
change name of local array [Chris Wilson]
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1463741647-15666-3-git-send-email-chris@chris-wilson.co.uk
The recently-added i915_gem_object_pin_map() can be further optimised
for "small" objects. To facilitate this, and simplify the error paths
before adding the new code, this patch pulls out the "mapping" part of
the operation (involving local allocations which must be undone before
return) into its own subfunction.
The next patch will then insert the new optimisation into the middle of
the now-separated subfunction.
This reorganisation will probably not affect the generated code, as the
compiler will most likely inline it anyway, but it makes the logical
structure a bit clearer and easier to modify.
v2:
Restructure loop-over-pages & error check [Chris Wilson]
v3:
Add page count to debug messages [Chris Wilson]
Convert WARN_ON() to GEM_BUG_ON()
v4:
Drop the DEBUG messages [Tvrtko Ursulin]
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1463741647-15666-2-git-send-email-chris@chris-wilson.co.uk
Found this while browsing Bspec. Looks like it applies to both skl and
kbl.
v2: Also for bxt (Art).
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Cc: "Runyan, Arthur J" <arthur.j.runyan@intel.com>
Reviewed-by: Sonika Jindal<sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463642060-30728-1-git-send-email-daniel.vetter@ffwll.ch
I just wanted to get rid of the rmw cycle for gen9, but this also
fixes some bugs we haven't carried over, like using recommended
precharge and timeout values.
Also I noticed that we don't set the fastwake sync length on skl, and
that's used by PSR2 selective updates. Fix that.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463590036-17824-6-git-send-email-daniel.vetter@ffwll.ch
On bdw/hsw we have a separate psr dp aux registers to set up, but on
bdw it's shared with the main dp aux thing. Which means any subsequent
dp aux transaction will trample over it, and hence must be done
beforehand.
Also this means we can't do any dp aux transactions while PSR is
active, or at least we must restore the old state.
Probably need a psr disable/enable pair around dp aux transactions in
general.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463590036-17824-5-git-send-email-daniel.vetter@ffwll.ch
This reverts
commit dfaf37baa0
Author: Rodrigo Vivi <rodrigo.vivi@intel.com>
Date: Mon Dec 7 14:45:20 2015 -0800
drm/i915: Fix idle_frames counter.
and
commit 97173eaf5f
Author: Rodrigo Vivi <rodrigo.vivi@intel.com>
Date: Tue Jul 7 16:28:55 2015 -0700
drm/i915: PSR: Increase idle_frames
and implements
commit d44b4dcbd1
Author: Rodrigo Vivi <rodrigo.vivi@intel.com>
Date: Fri Nov 14 08:52:31 2014 -0800
drm/i915: HSW/BDW PSR Set idle_frames = VBT + 1
without the hack to use 2 idle frames when VBT says 1. We keep the + 1
just for safety, although I haven't really figured out why that one
exists.
It's nonsense. idle_frames = number of frames where the screen is
entirely idle before we think about entering PSR.
idle_patter = part of link training, and we probably totally butchered
link training because we told the hw to entirely skip it. No wonder
PSR occasionally just fell over.
I suspect the reason we've increased idle frames is that it makes PSR
entry slightly less likely, and more likely to happen in a quite
system, which probably increased the changes the panel came back up
without link training. The proper fix is to implement link training
for PSR.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463590036-17824-3-git-send-email-daniel.vetter@ffwll.ch
The default of 0 is 500us of link training, but that's not enough for
some platforms. Decoding this correctly means we're using 2.5ms of
link training on these platforms, which fixes flickering issues
associated with enabling PSR.
v2: Unbotch the math a bit.
v3: Drop debug hunk.
v4: Improve commit message.
Tested-by: Lyude <cpaul@redhat.com>
Cc: Lyude <cpaul@redhat.com>
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95176
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: fritsch@kodi.tv
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463590036-17824-2-git-send-email-daniel.vetter@ffwll.ch
userptr directly only uses drm_device in a single interface where it
meant to use drm_i915_private (everywhere else we have to derive it from
the drm_i915_gem_object and so require going from drm_device).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463671036-3235-1-git-send-email-chris@chris-wilson.co.uk
If planes are added to the state after the call to
drm_atomic_helper_check_planes planes_changed may not be set
and we will not unpin the old framebuffer. This results in a
pin leak long after the framebuffer is destroyed, so to find
this add some checks when it happens.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-21-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
intel_unpin_work may not take the list lock because it requires the connector_mutex.
To prevent taking locks we add an array of old and new state. The old state to free,
the new state to commit and verify.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-18-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Create a work structure that will be used for all changes. This will
be used later on in the atomic commit function.
Changes since v1:
- Free old_crtc_state from unpin_work_fn properly.
Changes since v2:
- Add hunk for calling hw state verifier.
- Add missing support for color spaces.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-12-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
With intel_pipe_update begin/end we ensure that the mmio updates
don't run during vblank interrupt, using the hw counter we can
be sure that when current vblank count != vblank count at the time
of pipe_update_end the mmio update is complete.
This allows us to use mmio updates on all platforms, using the
update_plane call.
With Chris Wilson's patch to skip waiting for vblanks for
legacy_cursor_update this potentially leaves a small race
condition, in which update_plane can be called with a freed
crtc_state. Because of this commit acf4e84d61
("drm/i915: Avoid stalling on pending flips for legacy cursor updates")
is temporarily reverted.
Changes since v1:
- Split out the flip_work rename.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-9-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Rename intel_unpin_work to intel_flip_work and use it for mmio flips
and unpinning. Use flip_queued_req to hold the wait request in the
mmio case, and the vblank counter from intel_crtc_get_vblank_counter.
MMIO flips get their own path through intel_finish_page_flip_mmio,
handled on vblank. CS page flips go through *_cs.
Changes since v1:
- Clean up destinction between MMIO and CS flips.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-7-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Instead of calling prepare_flip right before calling finish_page_flip
do everything from prepare_page_flip in finish_page_flip.
Putting prepare and finish page_flip in a single step removes the need
for INTEL_FLIP_COMPLETE, so it can be removed. This simplifies the code
slightly.
Changes since v1:
- Invert if case to simplify code.
- Add missing barrier.
- Reword commit message.
Changes since v2:
- intel_page_flip_plane is removed.
- work->pending is turned into a bool.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-5-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Both intel_unpin_work.pending and intel_unpin_work.enable_stall_check
were used to see if work should be enabled. By only using pending
some special cases are gone, and access to unpin_work can be simplified.
A flip could previously be queued before
stallcheck was active. With the addition of the pending member
enable_stall_check became obsolete and can thus be removed.
Use this to only access work members untilintel_mark_page_flip_active
is called, or intel_queue_mmio_flip is used. This will prevent
use-after-free, and makes it easier to verify accesses.
Changes since v1:
- Reword commit message.
- Do not access unpin_work after intel_mark_page_flip_active.
- Add the right memory barriers.
Changes since v2:
- atomic_read() needs a full smp_rmb.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-3-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
This patch resizes the GuC WOPCM (specifically on BXT)
so that the GuC and RC6 memory spaces do not overlap.
v2:
Made calculation of WOPCM size into a separate function,
so that it's consistent between the firmware size-check
and the register-programming operations [Dave Gordon].
Issue: https://jira01.devtools.intel.com/browse/VIZ-6638
Signed-off-by: Peter Antoine <peter.antoine@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Tested-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463494365-26330-1-git-send-email-david.s.gordon@intel.com
- Unconditionally add plane states. Core helpers would have done this
in drm_atomic_helper_check_modeset, doing it once more won't cause
harm and is less fragile.
- Simplify the continue logic when disabling a pipe.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462779085-2458-1-git-send-email-daniel.vetter@ffwll.ch
During boot time, MST devices usually send a ton of hotplug events
irregardless of whether or not any physical hotplugs actually occurred.
Hotplugs mean connectors being created/destroyed, and the number of DRM
connectors changing under us. This isn't a problem if we use
fb_helper->connector_count since we only set it once in the code,
however if we use num_connector from struct drm_mode_config we risk it's
value changing under us. On top of that, there's even a chance that
dev->mode_config.num_connector != fb_helper->connector_count. If the
number of connectors happens to increase under us, we'll end up using
the wrong array size for memcpy and start writing beyond the actual
length of the array, occasionally resulting in kernel panics.
Note: This is just polish for 4.7, Dave Airlie's drm_connector
refcounting fixed these bugs for real. But it's good enough duct-tape
for stable kernel backporting, since backporting the refcounting
changes is way too invasive.
Cc: stable@vger.kernel.org
Signed-off-by: Lyude <cpaul@redhat.com>
[danvet: Clarify why we need this.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1463065021-18280-2-git-send-email-cpaul@redhat.com
In CABC (Content Adaptive Brightness Control) content grey level
scale can be increased while simultaneously decreasing
brightness of the backlight to achieve same perceived brightness.
The CABC is not standardized and panel vendors are free to follow
their implementation. The CABC implementaion here assumes that the
panels use standard SW register for control.
CABC is supported only when the PWM source for backlight is
from the panel.
v2 by Jani: rebase, renames, check cabc support earlier, etc.
Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/883faade74d2e598b143221ccc7df6daf4393a13.1461676337.git.jani.nikula@intel.com
If the source of the backlight PWM is from the
panel then the PWM can be controlled by DCS
command, this patch adds the support to
enable/disbale panel PWM, control backlight level
etc...
v2: Moving the CABC bkl functions to new file.(Jani)
v3: Rebase
v4: Rebase
v5: Use mipi_dsi_dcs_write() instead of mipi_dsi_dcs_write_buffer() (Jani)
Move DCS macro`s to include/video/mipi_display.h (Jani)
v6: Rename the file to intel_dsi_panel_pwm.c
Removing the CABC operations
v7 by Jani: renames, rebases, etc.
v8 by Jani: s/INTEL_BACKLIGHT_CABC/INTEL_BACKLIGHT_DSI_DCS/
v9 by Jani: rename init function to intel_dsi_dcs_init_backlight_funcs
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Deepak M <m.deepak@intel.com>
Reviewed-by: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/71238a4b14b8c3a6c04070c789f09f1b4bc00a15.1461676337.git.jani.nikula@intel.com
Call pwm_apply_args() just after requesting the PWM device so that the
polarity and period are initialized according to the information
provided in pwm_args.
This is an intermediate state, and pwm_apply_args() should be dropped as
soon as the atomic PWM infrastructure is in place and the driver makes
use of it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Backmerge request by Jani to get at
commit 249c4f538b
Author: Deepak M <m.deepak@intel.com>
Date: Wed Mar 30 17:03:39 2016 +0300
drm: Add new DCS commands in the enum list
Some simple conflicts in intel_dp.c.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
It's unused, and really this helper should only look at the state
structure and nothing else.
v2: Rebase on top of rockchip changes
v3: Drop unrelated hunk, spotted by Laurent.
v4: Rebase onto mtk driver merge.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Yao <mark.yao@rock-chips.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1462804451-15318-1-git-send-email-daniel.vetter@ffwll.ch
drm_gem_object_lookup() has never required the drm_device for its file
local translation of the user handle to the GEM object. Let's remove the
unused parameter and save some space.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: dri-devel@lists.freedesktop.org
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Fixup kerneldoc too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull x86 asm updates from Ingo Molnar:
"The main changes in this cycle were:
- MSR access API fixes and enhancements (Andy Lutomirski)
- early exception handling improvements (Andy Lutomirski)
- user-space FS/GS prctl usage fixes and improvements (Andy
Lutomirski)
- Remove the cpu_has_*() APIs and replace them with equivalents
(Borislav Petkov)
- task switch micro-optimization (Brian Gerst)
- 32-bit entry code simplification (Denys Vlasenko)
- enhance PAT handling in enumated CPUs (Toshi Kani)
... and lots of other cleanups/fixlets"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
x86/arch_prctl/64: Restore accidentally removed put_cpu() in ARCH_SET_GS
x86/entry/32: Remove asmlinkage_protect()
x86/entry/32: Remove GET_THREAD_INFO() from entry code
x86/entry, sched/x86: Don't save/restore EFLAGS on task switch
x86/asm/entry/32: Simplify pushes of zeroed pt_regs->REGs
selftests/x86/ldt_gdt: Test set_thread_area() deletion of an active segment
x86/tls: Synchronize segment registers in set_thread_area()
x86/asm/64: Rename thread_struct's fs and gs to fsbase and gsbase
x86/arch_prctl/64: Remove FSBASE/GSBASE < 4G optimization
x86/segments/64: When load_gs_index fails, clear the base
x86/segments/64: When loadsegment(fs, ...) fails, clear the base
x86/asm: Make asm/alternative.h safe from assembly
x86/asm: Stop depending on ptrace.h in alternative.h
x86/entry: Rename is_{ia32,x32}_task() to in_{ia32,x32}_syscall()
x86/asm: Make sure verify_cpu() has a good stack
x86/extable: Add a comment about early exception handlers
x86/msr: Set the return value to zero when native_rdmsr_safe() fails
x86/paravirt: Make "unsafe" MSR accesses unsafe even if PARAVIRT=y
x86/paravirt: Add paravirt_{read,write}_msr()
x86/msr: Carry on after a non-"safe" MSR access fails
...
Under full-ppgtt, access to the global GTT is carefully regulated
through hardware functions (i.e. userspace cannot read and write to
arbitrary locations in the GGTT via the GPU). With this restriction in
place, we can forgo clearing stale entries from the GGTT as they will
not be accessed.
For aliasing-ppgtt, we could almost do the same except that we do allow
userspace access to the global-GTT via execbuf in order to workraound
some quirks of certain instructions. (This execbuf path is filtered out
with EINVAL on full-ppgtt.)
The most dramatic effect this will have will be during resume, as with
full-ppgtt the GGTT is only used sparingly.
References: https://bugs.freedesktop.org/show_bug.cgi?id=94722
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Weinehall <david.weinehall@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Tested-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463207195-22076-4-git-send-email-chris@chris-wilson.co.uk
Now that we mark the object domains for having been restored from the
hibernation image, we not need to flush everything during resume and
can instead rely on the normal domain tracking to flush only when
required. The only caveat here are objects that are pinned for use by
the hardware, whose contents must be coherent for when the device
resumes reading from then (shortly afterwards with the driver assuming
the objects are in the correct domain).
References: https://bugs.freedesktop.org/show_bug.cgi?id=94722
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: David Weinehall <david.weinehall@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Tested-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463207195-22076-3-git-send-email-chris@chris-wilson.co.uk
When creating the hibernation image, the CPU will read the pages of all
objects and thus conflict with our domain tracking. We need to update
our domain tracking to accurately reflect the state on restoration.
v2: Perform the domain tracking inside freeze, before the image is
written, rather than upon restoration.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: David Weinehall <david.weinehall@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463207195-22076-2-git-send-email-chris@chris-wilson.co.uk
Currently for handling the extra hibernation phases we just call the
equivalent suspend/resume phases. In the next couple of patches, I wish
to specialise the hibernation phases to reduce the amount of work
required for handling GEM objects.
v2: There are more! Don't forget the freeze phases.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: David Weinehall <david.weinehall@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463207195-22076-1-git-send-email-chris@chris-wilson.co.uk
When we resume the watermark register may contain some BIOS leftovers,
or just the hardware reset values. We should ignore those as the
pipes will be off anyway, and so frobbing around with intermediate
watermarks doesn't make much sense.
In fact I think we should just throw the skip_intermediate_wm flag
out, and instead properly sanitize the "active" watermarks to match
the current plane and pipe states. The actual wm state readout might
also need a bit of work. But for now, let's continue with the
skip_intermediate_wm to keep the fix more minimal.
Fixes this sort of errors on resume
[drm:ilk_validate_pipe_wm] LP0 watermark invalid
[drm:intel_crtc_atomic_check] No valid intermediate pipe watermarks are possible
[drm:intel_display_resume [i915]] *ERROR* Restoring old state failed with -22
and a boatload of subsequent modeset BAT fails on my ILK.
v2:
- Rebase; the SKL atomic WM patches that just landed changed the WM
structure fields in intel_crtc_state slightly. (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: ed4a6a7ca8 ("drm/i915: Add two-stage ILK-style watermark programming (v11)")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463159442-20478-1-git-send-email-matthew.d.roper@intel.com
When we read out the watermark state from the hardware we're supposed to
transfer that into the active watermarks, but currently we fail to any
part of the active watermarks that isn't explicitly written. Let's clear
it all upfront.
Looks like this has been like this since the beginning, when I added the
readout. No idea why I didn't clear it up.
Cc: Matt Roper <matthew.d.roper@intel.com>
Fixes: 243e6a44b9 ("drm/i915: Init HSW watermark tracking in intel_modeset_setup_hw_state()")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463151318-14719-2-git-send-email-ville.syrjala@linux.intel.com
