Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pointer comparison is not sufficient for non-NULL device name matching,
so use strcmp(). Otherwise the semantics remain the same.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When one regulator supplies another allow the relationship to be specified
using names rather than struct regulators, in a similar manner to that
allowed for consumer supplies. This allows static configuration at compile
time, reducing the need for dynamic init code.
Also change the references to LINE supply to be system supply since line
is sometimes used for actual supplies and therefore potentially confusing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If the request for wdt_mem region fails, this patch modifies the driver
such that, it does not try to release the wdt_mem region on exit.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds HAVE_S3C2410_WATCHDOG to control inclusion of watchdog driver
for Samsung SoCs. This option will help to include the driver only for the
necessary machines and not for all for any given arch.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
For TCO V1 devices the programmed timeout was twice too long
because the fact that the TCO V1 timer needs to count down
twice before triggering the watchdog, wasn't accounted for.
Also the timeout values in the module description and error
message were clarified. And the _STS registers are 16 bit
instead of 8 bit.
Signed-off-by: Pádraig Brady <P@draigBrady.com>
Tested-by: Simon Kagstrom <simon.kagstrom@netinsight.se>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If we are not able to register then it is better to have
watchdog in disabled state than noticing a system reboot.
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Acked-By: Timo Kokkonen <timo.t.kokkonen@nokia.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Move the limited watchdog driver help from kernel-parameters.txt
to Documentation/watchdog/watchdog-parameters.txt and add info to it
for all watchdog drivers except the ones that have driver-specific
files already.
Correct minor comments and MODULE_PARM_DESC() text in 2 places.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix MODULE_PARM_DESC() strings in several watchdog drivers.
Some are simple as add a parenthesis.
Others are problems from __stringify() being used on a
variable name instead of a macro name, so the variable name
is produced in the string instead of its build-time value.
In these cases, create a macro for the value so that the
module param description string is useful.
Only pc87413_wdt has been built (due to toolchains).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Module roccat is a char device used to report special events of roccat hardware
to userland. These events include requests for on-screen-display of profile or
dpi settings or requests for execution of macro sequences that are not stored
in device. The information in these events depends on hid device implementation
and contains data that is not available in a single hid event or else hidraw
could have been used.
It is inspired by hidraw, but uses only one circular buffer for all readers.
The device is as generic as possible so that the functionality is usable by all
(kone and upcomming) roccat device drivers.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 58f9b0b024, "of: eliminate
of_device->node and dev_archdata->{of,prom}_node" changed the location
of the device_node pointer. Most drivers were converted to the new
location, but the xilinx_spi_of driver was missed and now fails to
compile.
This patch fixes up the xilinx_spi_of driver to use the new location.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Computation of the clock prescaler value returned bogus results if
the requested SPI clock was impossible to set. It now sets either
the maximum or minimum clock frequency, as appropriate.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
A number of files in drivers/spi fail checkincludes.pl due to the double
include of <linux/spi/spi_bitbang.h>.
The first include is needed to get the struct spi_bitbang definition and
the spi_bitbang_* function prototypes.
The second include happens after defining EXPAND_BITBANG_TXRX to get the
inlined bitbang_txrx_* utility functions.
The <linux/spi/spi_bitbang.h> header is also included by a number of other
spi drivers, as well as some arch/ code, in order to use struct spi_bitbang
and the associated functions.
To fix the double include, and remove any potential confusion about it, move
the inlined bitbang_txrx_* functions to a new private header in drivers/spi
and also remove the need to define EXPAND_BITBANG_TXRX.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since PSC could also be used in other modes than UART mode
we move PSC FIFO memory initialization from serial driver to
common platform code. The initialized FIFO memory slices may
not overlap, so the most easy way would be to configure them
all at once at init time for all PSC devices. This is now done
by this patch.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds an SPI master driver for the Cirrus EP93xx SPI controller found
in EP93xx chips.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Turbo mode allows to read data to shift register when rx-buffer
is full thus improving the perfomance. This feature is available
for RX-only mode.
In PIO turbo mode when the penultimate word is available
in RX-buffer the controller should be disabled before reading data
to prevent the next transaction triggering. The controller itself
handles the last word to be correctly loaded to shift-register and
then transferred to RX-buffer.
The turbo mode is enabled by setting turbo_mode parameter to 1.
This parameter is a part of omap2_mcspi_device_config structure
which is passed through the spi_device controller_data pointer.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The value 160 has been obtained as optimal in testing it for
wl1271 which use spi for communication.
In some sense this change might also influence on other spi devices
connected to omap2_mcspi controller.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This fix prevents queue being marked as "stopped", if data exists
in the queue list.
Signed-off-by: Grzegorz Sygieda <grzegorz.sygieda@tieto.com>
Signed-off-by: Lukasz Baj <lukasz.baj@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds support for a further ST variant of the PL022 called
PL023. Some differences in the control registers due to being
stripped down to SPI mode only, and a new clock feedback sample
delay config setting is available.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The PL022 SPI driver did not cleanly separate between the
original unmodified ARM version and the ST Microelectronics
versions. Split this more cleanly and fix some whitespace
moaning from checkpatch at the same time.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This fixes a typo were map_tx_dma is used instead of
map_rx_dma, casing the driver to unmap rx_dma when it
shouldn't.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
QE mode uses Little Endian so words > 8 bits are byte swapped.
Workaround this by always enforcing wordsize 8 for words
> 8 bits. Unfortunately this will not work for LSB transfers
where wordsize is > 8 bits so disable these for now.
Also move the different quirks into its own function to keep
mpc8xxx_spi_setup_transfer() sane.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Under abnormal termination, modify_qp() closes the QP, and async event
(AE) handling also attempts to close the same QP, causing a crash.
Fix this by checking the state of the QP before processing the AE.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enhance ethtool to read hardware registers for rcv/tx error stats.
Also add support for free pbl resources. Remove cq depth stats, which
are not used.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- wrap cq->cqidx_inc based on cq size.
- optimize t4_arm_cq logic.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
1) save the timestamp flit in the cq when we consume a CQE.
2) always compare the saved flit with the previous entry flit when
reading the next CQE entry. If the flits don't compare, then we
have overflowed.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We need 1 extra entry for the status page and 1 to always have 1 free
entry to detect when the queue is full.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The LLD now supports proper UP state change events, so move the RDMA
provider registration to UP path.
This fixes a crash when loading iw_cxgb4 _after_ the NFS/RDMA
transport is up and running.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In the RDMA core unregister path, kernel users will be calling down
into the T4 provider to release resources. So we cannot detach from
the LLD until this process completes.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fixes possible memory leak.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI function reset needs to invoked after fw init ioctl is issued.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functionality to keep the device awake until it is done with
the rx of any mcast/bcast frames which are pending on AP should
also be added to the hardwares which support auto sleep feature.
This patch fixes frequent failures in ARP resolution when it is
initiated by the other end. Currently auto sleep is enabled only
for ar9003 in ath9k.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The intent here is to test that "sta_id_r" is a valid pointer. We do
this same test later on in the function.
Btw iwl_add_bssid_station() is called from two places and "sta_id_r" is
a valid pointer from both callers.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is obviously a small picky thing. The original error handling code
doesn't free the most recent allocations which haven't been added to the
hif_dev->tx.tx_buf list yet.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After c11d8f89d3: "ath9k_htc: Simplify TX URB management" we no longer
assume that tx_buf is a non-null pointer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent changes to skb handling introduced a bug in the rt2800usb
TX descriptor writing whereby the length of the USB packet wasn't
calculated correctly.
Found via code inspection, as the devices themselves didn't seem to mind.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(Based on a patch created by Ondrej Zary)
In some circumstances the Ralink devices do not properly go to sleep
or wake up, with timeouts occurring.
Fix this by retrying telling the device that it has to wake up or
sleep.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 03ceedea97.
This patch was reported to cause a regression in which connectivity is
lost and cannot be reestablished after a suspend/resume cycle.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't use to_pci_dev in rt2x00pci_uninitialize to get the allocated irq
as it won't work for platform devices (SoC). Instead, use the irq field
that's already used everywhere else.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should use the same buffer size we set up for DMA also in the hardware
descriptor. Previously we used common->rx_bufsize for setting up the DMA
mapping, but used skb_tailroom(skb) for the size we tell to the hardware in the
descriptor itself. The problem is that skb_tailroom(skb) can give us a larger
value than the size we set up for DMA before. This allows the hardware to write
into memory locations not set up for DMA. In practice this should rarely happen
because all packets should be smaller than the maximum 802.11 packet size.
On the tested platform rx_bufsize is 2528, and we allocated an skb of 2559
bytes length (including padding for cache alignment) but sbk_tailroom() was
2592. Just consistently use rx_bufsize for all RX DMA memory sizes.
Also use the return value of the descriptor setup function.
Cc: stable@kernel.org
Signed-off-by: Bruno Randolf <br1@einfach.org>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change adds in the USB product ID for the Gyration
GYR4101US USB media center remote control. This remote
is similar enough to the other two devices that this driver
can be used without any other changes to get full support
for the remote.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6:
cmd640: fix kernel oops in test_irq() method
pdc202xx_old: ignore "FIFO empty" bit in test_irq() method
pdc202xx_old: wire test_irq() method for PDC2026x
IDE: pass IRQ flags to the IDE core
ide: fix comment typo in ide.h
* 'bkl/ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/random-tracing:
uml: Pushdown the bkl from harddog_kern ioctl
sunrpc: Pushdown the bkl from sunrpc cache ioctl
sunrpc: Pushdown the bkl from ioctl
autofs4: Pushdown the bkl from ioctl
uml: Convert to unlocked_ioctls to remove implicit BKL
ncpfs: BKL ioctl pushdown
coda: Clean-up whitespace problems in pioctl.c
coda: BKL ioctl pushdown
drivers: Push down BKL into various drivers
isdn: Push down BKL into ioctl functions
scsi: Push down BKL into ioctl functions
dvb: Push down BKL into ioctl functions
smbfs: Push down BKL into ioctl function
coda/psdev: Remove BKL from ioctl function
um/mmapper: Remove BKL usage
sn_hwperf: Kill BKL usage
hfsplus: Push down BKL into ioctl function
* git://git.infradead.org/battery-2.6:
ds2760_battery: Document ABI change
ds2760_battery: Make charge_now and charge_full writeable
power_supply: Add support for writeable properties
power_supply: Use attribute groups
power_supply: Add test_power driver
tosa_battery: Fix build error due to direct driver_data usage
wm97xx_battery: Quieten sparse warning (bat_set_pdata not declared)
ds2782_battery: Get rid of magic numbers in driver_data
ds2782_battery: Add support for ds2786 battery gas gauge
pda_power: Add function callbacks for suspend and resume
wm831x_power: Use genirq
Driver for Zipit Z2 battery chip
ds2782_battery: Fix clientdata on removal
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (25 commits)
sh: fix up sh7785lcr_32bit_defconfig.
arch/sh/lib/strlen.S: Checkpatch cleanup
sh: fix up sh7786 dmaengine build.
sh: guard cookie consistency across termination in the DMA driver
sh: prevent the DMA driver from unloading, while in use
sh: fix Oops in the serial SCI driver
sh: allow platforms to specify SD-card supported voltages
mmc: let MFD's provide supported Vdd card voltages to tmio_mmc
sh: disable SD-card write-protection detection on kfr2r09
mfd: pass platform flags down to the tmio_mmc driver
tmio: add a platform flag to disable card write-protection detection
sh: Add SDHI DMA support to migor
sh: Add SDHI DMA support to kfr2r09
sh: Add SDHI DMA support to ms7724se
sh: Add SDHI DMA support to ecovec
mmc: add DMA support to tmio_mmc driver, when used on SuperH
sh: prepare the SDHI MFD driver to pass DMA configuration to tmio_mmc.c
mmc: prepare tmio_mmc for passing of DMA configuration from the MFD cell
sh: add DMA slave definitions to sh7724
sh: add DMA slaves for two SDHI controllers to sh7722
...
This reverts commit 03ceedea97, since it
breaks resume from suspend-to-ram on Rafael's Acer Ferrari One.
NetworkManager thinks everything is ok, but it can't connect to the AP
to get an IP address after the resume.
In fact, it even breaks resume for non-ath9k chipsets: reverting it also
fixes Rafael's Toshiba Protege R500 with the iwlagn driver. As Johannes
says:
"Indeed, this patch needs to be reverted. That mac80211 change is wrong
and completely unnecessary."
Reported-and-requested-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Daniel Yingqiang Ma <yma.cool@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6:
of: change of_match_device to work with struct device
of: Remove duplicate fields from of_platform_driver
drivercore: Add of_match_table to the common device drivers
arch/microblaze: Move dma_mask from of_device into pdev_archdata
arch/powerpc: Move dma_mask from of_device into pdev_archdata
of: eliminate of_device->node and dev_archdata->{of,prom}_node
of: Always use 'struct device.of_node' to get device node pointer.
i2c/of: Allow device node to be passed via i2c_board_info
driver-core: Add device node pointer to struct device
of: protect contents of of_platform.h and of_device.h
of/flattree: Make unflatten_device_tree() safe to call from any arch
of/flattree: make of_fdt.h safe to unconditionally include.
The function name must be followed by a space, hypen, space, and a
short description.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After merging the driver-core tree, today's linux-next build (x86_64
allmodconfig) produced these warnings:
drivers/hid/hid-roccat-kone.c:694: warning: initialization from incompatible pointer type
drivers/hid/hid-roccat-kone.c:696: warning: initialization from incompatible pointer type
drivers/hid/hid-roccat-kone.c:701: warning: initialization from incompatible pointer type
drivers/hid/hid-roccat-kone.c:703: warning: initialization from incompatible pointer type
drivers/hid/hid-roccat-kone.c:708: warning: initialization from incompatible pointer type
drivers/hid/hid-roccat-kone.c:710: warning: initialization from incompatible pointer type
drivers/hid/hid-roccat-kone.c:715: warning: initialization from incompatible pointer type
drivers/hid/hid-roccat-kone.c:717: warning: initialization from incompatible pointer type
drivers/hid/hid-roccat-kone.c:722: warning: initialization from incompatible pointer type
drivers/hid/hid-roccat-kone.c:724: warning: initialization from incompatible pointer type
drivers/hid/hid-roccat-kone.c:729: warning: initialization from incompatible pointer type
drivers/hid/hid-roccat-kone.c:731: warning: initialization from incompatible pointer type
Introduced by commit 867040163f10f2b52b45bc573f330d6eb28f5914 ("sysfs:
add struct file* to bin_attr callbacks") from the driver-core tree
interacting with commit 14bf62cde7 ("HID:
add driver for Roccat Kone gaming mouse") from the hid tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The i.MX25 PDK uses RMII to communicate with its PHY. This patch adds
the ability to configure RMII, based on platform data.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes tun update its socket classid every time we
inject a packet into the network stack. This is so that any
updates made by the admin to the process writing packets to
tun is effected.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anomaly 05000230 (over sampling of the UART STOP bit) applies only when
the peripheral is operating in UART mode. So drop the anomaly handling
in the IRDA code.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dummy implementations for the optional CAPI controller operations
load_firmware and reset_ctr can cause userspace callers to hang
indefinitely. It's better not to implement them at all.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CAPI controller operation reset_ctr is marked as optional, and
not all drivers do implement it. Add a check to the kernel CAPI
whether it exists before trying to call it.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This assignment got deleted along with the checks by mistake. This
comes from: 8753d29fd "pppoe: remove unnecessary checks in
pppoe_flush_dev"
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan reported the patch 0baa080c75: "ethoc: use system memory
as buffer" introduced a potential null dereference.
1060 free:
1061 if (priv->dma_alloc)
^^^^^^^^^^^^^^^
priv can be null here.
He also suggested that the error handling is not complete.
This patch fixes the null priv issue and improves resources
releasing in ethoc_probe() and ethoc_remove().
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use random mac addr for interface when associating port-profile to
dynamic enic device, in the case no mac addr was previous assigned.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ib_qib driver is taking over support for QLogic PCIe QLE devices,
so remove support for them from ib_ipath. The ib_ipath driver now
supports only the obsolete QLogic Hyper-Transport IB host channel
adapter (model QHT7140).
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a low-level IB driver for QLogic PCIe adapters.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
drivers/gpu/drm/nouveau/nv40_graph.c: In function `nv40_graph_init':
drivers/gpu/drm/nouveau/nv40_graph.c:400: warning: the frame size of 1184 bytes is larger than 1024 bytes
drivers/gpu/drm/radeon/radeon_atombios.c: In function `radeon_get_atom_connector_info_from_supported_devices_table':
drivers/gpu/drm/radeon/radeon_atombios.c:857: warning: the frame size of 1872 bytes is larger than 1024 bytes
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When CONFIG_ACPI_BUTTON=m (and probably when ACPI_BUTTON is not enabled)
and NOUVEAU is built-in (not as a loadable module):
nouveau_connector.c:(.text+0xe17ce): undefined reference to `acpi_lid_open'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I think it's good to release the AGP bridge at suspend
and reacquire it at resume. Also fix :
https://bugzilla.kernel.org/show_bug.cgi?id=15969
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
tx_dma/rx_dma are already set to a dummy buffer when no
tx/rx buffer and t->tx_dma/t->rx_dma does not contain a dma
address, but NULL.
This may lead to corruption of kernel memory. Fix this by
leaving tx_dma/rx_dma alone.
Do not INIT_TX_RX while controller is enabled, this is bad according
to the MPC8321 manual.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
If all descriptors on a channel are terminated or the channel is released,
update the completed cookie counter to match the last cookie. This prevents
inconsistency warning on resumed DMA operation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This prevents the driver from unloading, while it is in use. Unloading of the
driver, while its DMA channels are held, leads to a kernel Oops.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix an Oops, triggering, if the DMA buffer allocation for the Rx channel in
sh-sci.c fails.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Boards can have different supplied voltages on different SD card slots. This
information has to be passed down to the SD/MMC driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Write-protection status is not always available, e.g., micro-SD cards do not
have a write-protection switch at all. This patch adds a flag to let platforms
force tmio_mmc to consider the card writable.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SDHI controllers on SuperH, served by the tmio_mmc driver, can use slave DMA
for data transfer. This patch adds support for the dmaengine API to the
tmio_mmc driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Pass DMA slave IDs from platform down to the tmio_mmc driver, to be used
for dmaengine configuration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The of_node pointer is now stored directly in struct device, so
of_match_device() should work with any device, not just struct of_device.
This patch changes the interface to of_match_device() to accept a
struct device instead of struct of_device.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
OF-style matching can be available to any device, on any type of bus.
This patch allows any driver to provide an OF match table when CONFIG_OF
is enabled so that drivers can be bound against devices described in
the device tree.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
By moving dma_mask into pdev_archdata, and adding archdata to
struct of_device, it makes it possible to substitute of_device
with struct platform_device, which is a stepping stone to
removing the of_platform bus entirely.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix printk formats:
drivers/video/fbmem.c: In function 'fb_do_apertures_overlap':
drivers/video/fbmem.c:1494: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'resource_size_t'
drivers/video/fbmem.c:1494: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'resource_size_t'
drivers/video/fbmem.c:1494: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'resource_size_t'
drivers/video/fbmem.c:1494: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'resource_size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (69 commits)
fix handling of offsets in cris eeprom.c, get rid of fake on-stack files
get rid of home-grown mutex in cris eeprom.c
switch ecryptfs_write() to struct inode *, kill on-stack fake files
switch ecryptfs_get_locked_page() to struct inode *
simplify access to ecryptfs inodes in ->readpage() and friends
AFS: Don't put struct file on the stack
Ban ecryptfs over ecryptfs
logfs: replace inode uid,gid,mode initialization with helper function
ufs: replace inode uid,gid,mode initialization with helper function
udf: replace inode uid,gid,mode init with helper
ubifs: replace inode uid,gid,mode initialization with helper function
sysv: replace inode uid,gid,mode initialization with helper function
reiserfs: replace inode uid,gid,mode initialization with helper function
ramfs: replace inode uid,gid,mode initialization with helper function
omfs: replace inode uid,gid,mode initialization with helper function
bfs: replace inode uid,gid,mode initialization with helper function
ocfs2: replace inode uid,gid,mode initialization with helper function
nilfs2: replace inode uid,gid,mode initialization with helper function
minix: replace inode uid,gid,mode init with helper
ext4: replace inode uid,gid,mode init with helper
...
Trivial conflict in fs/fs-writeback.c (mark bitfields unsigned)
* git://git.infradead.org/iommu-2.6:
intel-iommu: Set a more specific taint flag for invalid BIOS DMAR tables
intel-iommu: Combine the BIOS DMAR table warning messages
panic: Add taint flag TAINT_FIRMWARE_WORKAROUND ('I')
panic: Allow warnings to set different taint flags
intel-iommu: intel_iommu_map_range failed at very end of address space
intel-iommu: errors with smaller iommu widths
intel-iommu: Fix boot inside 64bit virtualbox with io-apic disabled
intel-iommu: use physfn to search drhd for VF
intel-iommu: Print out iommu seq_id
intel-iommu: Don't complain that ACPI_DMAR_SCOPE_TYPE_IOAPIC is not supported
intel-iommu: Avoid global flushes with caching mode.
intel-iommu: Use correct domain ID when caching mode is enabled
intel-iommu mistakenly uses offset_pfn when caching mode is enabled
intel-iommu: use for_each_set_bit()
intel-iommu: Fix section mismatch dmar_ir_support() uses dmar_tbl.
* 'virtio' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (27 commits)
drivers/char: Eliminate use after free
virtio: console: Accept console size along with resize control message
virtio: console: Store each console's size in the console structure
virtio: console: Resize console port 0 on config intr only if multiport is off
virtio: console: Add support for nonblocking write()s
virtio: console: Rename wait_is_over() to will_read_block()
virtio: console: Don't always create a port 0 if using multiport
virtio: console: Use a control message to add ports
virtio: console: Move code around for future patches
virtio: console: Remove config work handler
virtio: console: Don't call hvc_remove() on unplugging console ports
virtio: console: Return -EPIPE to hvc_console if we lost the connection
virtio: console: Let host know of port or device add failures
virtio: console: Add a __send_control_msg() that can send messages without a valid port
virtio: Revert "virtio: disable multiport console support."
virtio: add_buf_gfp
trans_virtio: use virtqueue_xxx wrappers
virtio-rng: use virtqueue_xxx wrappers
virtio_ring: remove a level of indirection
virtio_net: use virtqueue_xxx wrappers
...
Fix up conflicts in drivers/net/virtio_net.c due to new virtqueue_xxx
wrappers changes conflicting with some other cleanups.
* 'modules' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
module: drop the lock while waiting for module to complete initialization.
MODULE_DEVICE_TABLE(isapnp, ...) does nothing
hisax_fcpcipnp: fix broken isapnp device table.
isapnp: move definitions to mod_devicetable.h so file2alias can reach them.
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (32 commits)
Move N014, N051 and CR620 dmi information to load scm dmi table
drivers/platform/x86/eeepc-wmi.c: fix build warning
X86 platfrom wmi: Add debug facility to dump WMI data in a readable way
X86 platform wmi: Also log GUID string when an event happens and debug is set
X86 platform wmi: Introduce debug param to log all WMI events
Clean up all objects used by scm model when driver initial fail or exit
msi-laptop: fix up some coding style issues found by checkpatch
msi-laptop: Add i8042 filter to sync sw state with BIOS when function key pressed
msi-laptop: Set rfkill init state when msi-laptop intiial
msi-laptop: Add MSI CR620 notebook dmi information to scm models table
msi-laptop: Add N014 N051 dmi information to scm models table
drivers/platform/x86: Use kmemdup
drivers/platform/x86: Use kzalloc
drivers/platform/x86: Clarify the MRST IPC driver description slightly
eeepc-wmi: depends on BACKLIGHT_CLASS_DEVICE
IPC driver for Intel Mobile Internet Device (MID) platforms
classmate-laptop: Add RFKILL support.
thinkpad-acpi: document backlight level writeback at driver init
thinkpad-acpi: clean up ACPI handles handling
thinkpad-acpi: don't depend on led_path for led firmware type (v2)
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
DMAENGINE: extend the control command to include an arg
async_tx: trim dma_async_tx_descriptor in 'no channel switch' case
DMAENGINE: DMA40 fix for allocation of logical channel 0
DMAENGINE: DMA40 support paused channel status
dmaengine: mpc512x: Use resource_size
DMA ENGINE: Do not reset 'private' of channel
ioat: Remove duplicated devm_kzalloc() calls for ioatdma_device
ioat3: disable cacheline-unaligned transfers for raid operations
ioat2,3: convert to producer/consumer locking
ioat: convert to circ_buf
DMAENGINE: Support for ST-Ericssons DMA40 block v3
async_tx: use of kzalloc/kfree requires the include of slab.h
dmaengine: provide helper for setting txstate
DMAENGINE: generic channel status v2
DMAENGINE: generic slave control v2
dma: timb-dma: Update comment and fix compiler warning
dma: Add timb-dma
DMAENGINE: COH 901 318 fix bytesleft
DMAENGINE: COH 901 318 rename confusing vars
* 'for-linus' of git://neil.brown.name/md: (45 commits)
md: don't insist on valid event count for spare devices.
md: simplify updating of event count to sometimes avoid updating spares.
md/raid6: Fix raid-6 read-error correction in degraded state
md: restore ability of spare drives to spin down.
md: Fix read balancing in RAID1 and RAID10 on drives > 2TB
md/linear: standardise all printk messages
md/raid0: tidy up printk messages.
md/raid10: tidy up printk messages.
md/raid1: improve printk messages
md/raid5: improve consistency of error messages.
md: remove EXPERIMENTAL designation from RAID10
md: allow integers to be passed to md/level
md: notify mdstat waiters of level change
md/raid4: permit raid0 takeover
md/raid1: delay reads that could overtake behind-writes.
md/raid1: fix confusing 'redirect sector' message.
md: don't unregister the thread in mddev_suspend
md: factor out init code for an mddev
md: pass mddev to make_request functions rather than request_queue
md: call md_stop_writes from md_stop
...
Conflicts:
drivers/md/md.c
- Resolved conflict in md_update_sb
- Added extra 'NULL' arg to new instance of sysfs_get_dirent.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that the last user passing a NULL file pointer is gone we can remove
the redundant dentry argument and associated hacks inside vfs_fsynmc_range.
The next step will be removig the dentry argument from ->fsync, but given
the luck with the last round of method prototype changes I'd rather
defer this until after the main merge window.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (577 commits)
Staging: ramzswap: Handler for swap slot free callback
swap: Add swap slot free callback to block_device_operations
swap: Add flag to identify block swap devices
Staging: vt6655: use ETH_FRAME_LEN macro instead of custom one
Staging: vt6655: use ETH_DATA_LEN macro instead of custom one
Staging: vt6655: use ETH_FCS_LEN macro instead of custom one
Staging: vt6656: use ETH_HLEN macro instead of custom one
Staging: comedi: quatech_daqp_cs.c Replace eos semaphore with a completion.
Staging: dt3155v4l: remove private memory allocator
Staging: crystalhd: Remove typedefs from driver
Staging: winbond: Fix for pointer name format issue in mds.c
Staging: vt6656: removed custom UCHAR/USHORT/UINT/ULONG/ULONGLONG typedefs
Staging: vt6656: removed custom CHAR/SHORT/INT/LONG typedefs
Staging: comedi: Altered the way printk is used in 8255.c
staging: iio: adis16350 and similar IMU driver
Staging: iio: max1363 Fix two bugs in single_channel_from_ring
Staging: iio: adis16220 extract bin_attribute structures from state
Staging: iio: adis16220 vibration sensor driver
Staging: comedi: Kconfig dependancy fixes
Staging: comedi: fix up build error from last Kconfig changes
...
* 'for-2.6.35' of git://git.kernel.dk/linux-2.6-block: (86 commits)
pipe: set lower and upper limit on max pages in the pipe page array
pipe: add support for shrinking and growing pipes
drbd: This is now equivalent to drbd release 8.3.8rc1
drbd: Do not free p_uuid early, this is done in the exit code of the receiver
drbd: Null pointer deref fix to the large "multi bio rewrite"
drbd: Fix: Do not detach, if a bio with a barrier fails
drbd: Ensure to not trigger late-new-UUID creation multiple times
drbd: Do not Oops when C_STANDALONE when uuid gets generated
writeback: fix mixed up arguments to bdi_start_writeback()
writeback: fix problem with !CONFIG_BLOCK compilation
block: improve automatic native capacity unlocking
block: use struct parsed_partitions *state universally in partition check code
block,ide: simplify bdops->set_capacity() to ->unlock_native_capacity()
block: restart partition scan after resizing a device
buffer: make invalidate_bdev() drain all percpu LRU add caches
block: remove all rcu head initializations
writeback: fixups for !dirty_writeback_centisecs
writeback: bdi_writeback_task() must set task state before calling schedule()
writeback: ensure that WB_SYNC_NONE writeback with sb pinned is sync
drivers/block/drbd: Use kzalloc
...
Removed check to prevent hotplug of display devices within pciehp.
Originally this was thought to have been required within the PCI
Hotplug specification for some legacy devices. However there is
no such requirement in the most recent revision. The check prevents
hotplug of not only display devices but also computational GPUs
which require serviceability.
Signed-off-by: Praveen Kalamegham <praveen@nextio.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
At the moment only PCI-E briges can be flagged as hotplug, thus
allowing manual resource preallocation via pci=hpmemsize=nnM and
pci=hpiosize=nnM kernel parameters. Some PCI hotplug bridges, e.g.
PLX 6254 can also benefit from this functionalily, as kernel fails
to properly allocate their resources when hotplug device is added
and PCI bus is rescanned.
This patch adds header quirk for PLX 6254 that marks this bridge
as hotplug. Other PCI bridges with similar problems can use it
as well.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'msm-mmc_sdcc' of git://codeaurora.org/quic/kernel/dwalker/linux-msm:
drivers: mmc: msm_sdcc: Add EMBEDDED_SDIO support
mmc: msm_sdcc: Fix issue where clocks could be disabled mid transaction
mmc: msm_sdcc: Fix the dma exec function to use the proper delays
mmc: msm_sdcc: Don't set host->curr.mrq until after we're sure the busclk timer won't fire
mmc: msm_sdcc: Enable busclk idle timer for power savings
mmc: msm_sdcc: Don't disable interrupts while suspending
mmc: msm_sdcc: Fix issue where we might not end a sucessfull request
mmc: msm_sdcc: Featurize busclock power save and disable it by default
mmc: msm_sdcc: Fix bug where busclk expiry timer was not properly disabled
mmc: msm_sdcc: Reduce command timeouts and improve reliability.
mmc: msm_sdcc: Schedule clock disable after probe
mmc: msm_sdcc: Wrap readl/writel calls with appropriate clk delays
mmc: msm_sdcc: Driver clocking/irq improvements
msm: Add 'execute' datamover callback
mmc: msm_sdcc: Snoop SDIO_CCCR_ABORT register
mmc: msm_sdcc: Clean up clock management and add a 10us delay after enabling clocks
As a follow-up to the thread about RTC support for some Loongson 2E/2F
boards, this patch tries to address the "REVISIT"/"FIXME" comments about
rtc binary mode handling and allow rtc to work with rtc in binary mode.
I've also raised the message about 24-h mode not supported to warning
otherwise, one may end up with no rtc without any message in the kernel
log.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
To: linux-mips@linux-mips.org
To: rtc-linux@googlegroups.com
Cc: david-b@pacbell.net
Cc: a.zummo@towertech.it
Cc: akpm@linux-foundation.org
Patchwork: http://patchwork.linux-mips.org/patch/1158/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Conflicts:
drivers/staging/arlan/arlan-main.c
drivers/staging/comedi/drivers/cb_das16_cs.c
drivers/staging/cx25821/cx25821-alsa.c
drivers/staging/dt3155/dt3155_drv.c
drivers/staging/hv/hv.c
drivers/staging/netwave/netwave_cs.c
drivers/staging/wavelan/wavelan.c
drivers/staging/wavelan/wavelan_cs.c
drivers/staging/wlags49_h2/wl_cs.c
This required a bit of hand merging due to the conflicts
that happened in the later .34-rc releases, as well as
some staging driver changing coming in through other trees
(v4l and pcmcia).
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Introduced a few days ago:
commit 45bb912bd5
Author: Lars Ellenberg <lars.ellenberg@linbit.com>
Date: Fri May 14 17:10:48 2010 +0200
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Got introduces with
commit 0c3f34516e
Author: Philipp Reisner <philipp.reisner@linbit.com>
Date: Mon May 17 16:10:43 2010 +0200
drbd: Create new current UUID as late as possible
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Remove (hopefully) last use of WEXT in rndis_wlan. Replace wireless_send_event
with missing cfg80211_disconnected in rndis_wlan_do_link_down_work.
Reported-by: "Rogério Brito" <rbrito@ime.usp.br>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We tried to squeeze as much AR9003 support into this kernel
release cycle but there are a few features which are still
being tested and developed. Some of these features are critical
to the stable operation of AR9003 so for now disable AR9003 support
all together. This will get re-enabled once all necessary features
are in place but very likely will not happen for 2.6.35.
Reviewed-by: Don Breslin <don.breslin@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current frame length used by the driver for RX frames is the SPI bus
transfer length. This length has padding bytes, which do not belong to the
WLAN frame.
As there is no other length information in the WLAN frame except the skb
length this problem caused for instance extra ESSID's to be listed at the
end of scan results (IE id 0) with zero length.
Fix the frame length by removing padding.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is possible for internal scan to race against itself if the device is
not returning the scan results from first requests. What happens in this
case is the cleanup done during the abort of the first internal scan also
cleans up part of the new scan, causing it to access memory it shouldn't.
Here are details:
* First internal scan is triggered and scan command sent to device.
* After seven seconds there is no scan results so the watchdog timer
triggers a scan abort.
* The scan abort succeeds and a SCAN_COMPLETE_NOTIFICATION is received for
failed scan.
* During processing of SCAN_COMPLETE_NOTIFICATION we clear STATUS_SCANNING
and queue the "scan_completed" work.
** At this time, since the problem that caused the internal scan in first
place is still present, a new internal scan is triggered.
The behavior at this point is a bit different between 2.6.34 and 2.6.35
since 2.6.35 has a lot of this synchronized. The rest of the race
description will thus be generalized.
** As part of preparing for the scan "is_internal_short_scan" is set to
true.
* At this point the completion work for fist scan is run. As part of this
there is some locking missing around the "is_internal_short_scan"
variable and it is set to "false".
** Now the second scan runs and it considers itself a real (not internal0
scan and thus causes problems with wrong memory being accessed.
The fix is twofold.
* Since "is_internal_short_scan" should be protected by mutex, fix this in
scan completion work so that changes to it can be serialized.
* Do not queue a new internal scan if one is in progress.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=15824
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (92 commits)
powerpc: Remove unused 'protect4gb' boot parameter
powerpc: Build-in e1000e for pseries & ppc64_defconfig
powerpc/pseries: Make request_ras_irqs() available to other pseries code
powerpc/numa: Use ibm,architecture-vec-5 to detect form 1 affinity
powerpc/numa: Set a smaller value for RECLAIM_DISTANCE to enable zone reclaim
powerpc: Use smt_snooze_delay=-1 to always busy loop
powerpc: Remove check of ibm,smt-snooze-delay OF property
powerpc/kdump: Fix race in kdump shutdown
powerpc/kexec: Fix race in kexec shutdown
powerpc/kexec: Speedup kexec hash PTE tear down
powerpc/pseries: Add hcall to read 4 ptes at a time in real mode
powerpc: Use more accurate limit for first segment memory allocations
powerpc/kdump: Use chip->shutdown to disable IRQs
powerpc/kdump: CPUs assume the context of the oopsing CPU
powerpc/crashdump: Do not fail on NULL pointer dereferencing
powerpc/eeh: Fix oops when probing in early boot
powerpc/pci: Check devices status property when scanning OF tree
powerpc/vio: Switch VIO Bus PM to use generic helpers
powerpc: Avoid bad relocations in iSeries code
powerpc: Use common cpu_die (fixes SMP+SUSPEND build)
...
* 'drm-for-2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (207 commits)
drm/radeon/kms/pm/r600: select the mid clock mode for single head low profile
drm/radeon: fix power supply kconfig interaction.
drm/radeon/kms: record object that have been list reserved
drm/radeon: AGP memory is only I/O if the aperture can be mapped by the CPU.
drm/radeon/kms: don't default display priority to high on rs4xx
drm/edid: fix typo in 1600x1200@75 mode
drm/nouveau: fix i2c-related init table handlers
drm/nouveau: support init table i2c device identifier 0x81
drm/nouveau: ensure we've parsed i2c table entry for INIT_*I2C* handlers
drm/nouveau: display error message for any failed init table opcode
drm/nouveau: fix init table handlers to return proper error codes
drm/nv50: support fractional feedback divider on newer chips
drm/nv50: fix monitor detection on certain chipsets
drm/nv50: store full dcb i2c entry from vbios
drm/nv50: fix suspend/resume with DP outputs
drm/nv50: output calculated crtc pll when debugging on
drm/nouveau: dump pll limits entries when debugging is on
drm/nouveau: bios parser fixes for eDP boards
drm/nouveau: fix a nouveau_bo dereference after it's been destroyed
drm/nv40: remove some completed ctxprog TODOs
...
* 'dbg-early-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
echi-dbgp: Add kernel debugger support for the usb debug port
earlyprintk,vga,kdb: Fix \b and \r for earlyprintk=vga with kdb
kgdboc: Add ekgdboc for early use of the kernel debugger
x86,early dr regs,kgdb: Allow kernel debugger early dr register access
x86,kgdb: Implement early hardware breakpoint debugging
x86, kgdb, init: Add early and late debug states
x86, kgdb: early trap init for early debug
* 'kdb-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb: (25 commits)
kdb,debug_core: Allow the debug core to receive a panic notification
MAINTAINERS: update kgdb, kdb, and debug_core info
debug_core,kdb: Allow the debug core to process a recursive debug entry
printk,kdb: capture printk() when in kdb shell
kgdboc,kdb: Allow kdb to work on a non open console port
kgdb: Add the ability to schedule a breakpoint via a tasklet
mips,kgdb: kdb low level trap catch and stack trace
powerpc,kgdb: Introduce low level trap catching
x86,kgdb: Add low level debug hook
kgdb: remove post_primary_code references
kgdb,docs: Update the kgdb docs to include kdb
kgdboc,keyboard: Keyboard driver for kdb with kgdb
kgdb: gdb "monitor" -> kdb passthrough
sparc,sunzilog: Add console polling support for sunzilog serial driver
sh,sh-sci: Use NO_POLL_CHAR in the SCIF polled console code
kgdb,8250,pl011: Return immediately from console poll
kgdb: core changes to support kdb
kdb: core for kgdb back end (2 of 2)
kdb: core for kgdb back end (1 of 2)
kgdb,blackfin: Add in kgdb_arch_set_pc for blackfin
...
bdops->set_capacity() is unnecessarily generic. All that's required
is a simple one way notification to lower level driver telling it to
try to unlock native capacity. There's no reason to pass in target
capacity or return the new capacity. The former is always the
inherent native capacity and the latter can be handled via the usual
device resize / revalidation path. In fact, the current API is always
used that way.
Replace ->set_capacity() with ->unlock_native_capacity() which take
only @disk and doesn't return anything. IDE which is the only current
user of the API is converted accordingly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (113 commits)
omap4: Add support for i2c init
omap: Fix i2c platform init code for omap4
OMAP2 clock: fix recursive spinlock attempt when CONFIG_CPU_FREQ=y
OMAP powerdomain, hwmod, omap_device: add some credits
OMAP4 powerdomain: Support LOWPOWERSTATECHANGE for powerdomains
OMAP3 clock: add support for setting the divider for sys_clkout2 using clk_set_rate
OMAP4 powerdomain: Fix pwrsts flags for ALWAYS ON domains
OMAP: timers: Fix clock source names for OMAP4
OMAP4 clock: Support clk_set_parent
OMAP4: PRCM: Add offset defines for all CM registers
OMAP4: PRCM: Add offset defines for all PRM registers
OMAP4: PRCM: Remove duplicate definition of base addresses
OMAP4: PRM: Remove MPU internal code name and apply PRCM naming convention
OMAP4: CM: Remove non-functional registers in ES1.0
OMAP: hwmod: Replace WARN by pr_warning for clockdomain check
OMAP: hwmod: Rename hwmod name for the MPU
OMAP: hwmod: Do not exit the iteration if one clock init failed
OMAP: hwmod: Replace WARN by pr_warning if clock lookup failed
OMAP: hwmod: Remove IS_ERR check with omap_clk_get_by_name return value
OMAP: hwmod: Fix wrong pointer iteration in oh->slaves
...
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-nforce2: Remove redundant error messages on ACPI conflict
i2c: Use <linux/io.h> instead of <asm/io.h>
i2c-algo-pca: Fix coding style issues
i2c-dev: Fix all coding style issues
i2c-core: Fix some coding style issues
i2c-gpio: Move initialization code to subsys_initcall()
i2c-parport: Make template structure const
i2c-dev: Remove unnecessary casts
at24: Fall back to byte or word reads if needed
i2c-stub: Expose the default functionality flags
i2c/scx200_acb: Make PCI device ids constant
i2c-i801: Fix all checkpatch warnings
i2c-i801: All newer devices have all the optional features
i2c-i801: Let the user disable selected driver features
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (25 commits)
serial: Tidy REMOTE_DEBUG
serial: isicomm: handle running out of slots
serial: bfin_sport_uart: Use resource size to fix off-by-one error
tty: fix obsolete comment on tty_insert_flip_string_fixed_flag
serial: Add driver for the Altera UART
serial: Add driver for the Altera JTAG UART
serial: timbuart: make sure last byte is sent when port is closed
serial: two branches the same in timbuart_set_mctrl()
serial: uartlite: move from byte accesses to word accesses
tty: n_gsm: depends on NET
tty: n_gsm line discipline
serial: TTY: new ldiscs for staging
serial: bfin_sport_uart: drop redundant cpu depends
serial: bfin_sport_uart: drop the experimental markings
serial: bfin_sport_uart: pull in bfin_sport.h for SPORT defines
serial: bfin_sport_uart: only enable SPORT TX if data is to be sent
serial: bfin_sport_uart: drop useless status masks
serial: bfin_sport_uart: zero sport_uart_port if allocated dynamically
serial: bfin_sport_uart: protect changes to uart_port
serial: bfin_sport_uart: add support for CTS/RTS via GPIOs
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (38 commits)
net: Expose all network devices in a namespaces in sysfs
hotplug: netns aware uevent_helper
kobj: Send hotplug events in the proper namespace.
netlink: Implment netlink_broadcast_filtered
net/sysfs: Fix the bitrot in network device kobject namespace support
netns: Teach network device kobjects which namespace they are in.
kobject: Send hotplug events in all network namespaces
driver-core: fix Typo in drivers/base/core.c for CONFIG_MODULE
pci: check caps from sysfs file open to read device dependent config space
sysfs: add struct file* to bin_attr callbacks
sysfs: Remove usage of S_BIAS to avoid merge conflict with the vfs tree
sysfs: Don't use enums in inline function declaration.
sysfs-namespaces: add a high-level Documentation file
sysfs: Comment sysfs directory tagging logic
driver core: Implement ns directory support for device classes.
sysfs: Implement sysfs_delete_link
sysfs: Add support for tagged directories with untagged members.
sysfs: Implement sysfs tagged directory support.
kobj: Add basic infrastructure for dealing with namespaces.
sysfs: Remove double free sysfs_get_sb
...
Add a new parameter to ib_register_device() so that low-level device
drivers can pass in a pointer to a callback function that will be
called for each port that is registered in sysfs. This allows
low-level device drivers to create files in
/sys/class/infiniband/<hca>/ports/<N>/
without having to poke through the internals of the RDMA sysfs handling.
There is no need for an unregister function since the kobject
reference will go to zero when ib_unregister_device() is called.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The removal of the 'waitqueue_active()' test in commit d7d05548a6
("[SCSI] iscsi_tcp: fix relogin/shutdown hang") got incorrectly resolved
by David when he back-merged the main git tree into the networking tree
in commit 278554bd65 ("Merge branch 'master' of master.kernel.org:...").
There was a content conflict due to 'sock->sk->sk_sleep' being changed
into 'sk_sleep(sock->sk)' in the networking tree, but David didn't pick
up the iscsi change from the main tree.
Reported-by: James Bottomley <James.Bottomley@suse.de>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ACPI subsystem strictly checks for resource conflicts. When there's
a conflict, it outputs a warning message with all the details needed to
properly diagnose the underlying issue. However, the i2c-nforce2 driver
also prints its own message. Not only is the message redundant, it is at
the KERN_ERR level, which overrides some bootsplash screens for no good
reason. This change removes the two lines that print out the error
messages.
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As warned by checkpatch.pl, <linux/io.h> should be used instead of
<asm/io.h>.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix up some coding style issues. i2c-algo-pca.c has been built
successfully after applying this patch and the binary object is
still exactly the same. Other issues found by checkpatch.pl were
voluntarily not fixed, either to keep readability, or because of
false positive errors.
Signed-off-by: Farid Hammane <farid.hammane@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix all coding style issues found by checkpatch.pl.
Signed-off-by: Farid Hammane <farid.hammane@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix up coding style issues found by the checkpatch.pl tool.
Signed-off-by: Farid Hammane <farid.hammane@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
GPIO driven I2C bus can be used for controlling the PMIC chip. The
example of such configuration is Samsung Aquila board.
This patch moves initialization code to subsys_initcall() to ensure
that the i2c bus is available early so the regulators can be quickly
probed and available for other devices on their probe() call.
Such solution has been proposed by Mark Brown to fix the problem of
the regulators not beeing available on the peripheral device probe():
http://lists.infradead.org/pipermail/linux-arm-kernel/2010-March/011971.html
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The private_data member of struct file is a void *, there is no need
to cast it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Increase the portability of the at24 driver by letting it read from
EEPROM chips connected to cheap SMBus controllers that support neither
raw I2C messages nor even I2C block reads. All SMBus controllers
should support either word reads or byte reads, so read support
becomes universal, much like with the legacy "eeprom" driver.
Obviously, this only works with EEPROM chips up to AT24C16, that use
8-bit offset addressing. 16-bit offset addressing is almost impossible
to support on SMBus controllers.
I did not add universal support for writes, as I had no immediate need
for this, but it could be added later if needed (with the same
performance issue as byte and word reads have, of course.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Konstantin Lazarev <klazarev@sbcglobal.net>
It is easier to adjust the flags when you know their default value.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Make PCI device ids constant as we just did for many other i2c bus
drivers already.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Márton Németh <nm127@freemail.hu>
Fix all checkpatch warnings. No functional changes are made.
Signed-off-by: Ivo Manca <pinkel@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Only the oldest devices lack some of the features supported by this
driver. List them explicitly, and default to all features enabled for
all other chips, including the ones added through sysfs. This will
make future driver maintenance easier.
In the unlikely event of a not yet supported device not implementing
all the features, one can always use the disable_features module
parameter to prevent the driver from attempting to use them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Seth Heasley <seth.heasley@intel.com>
Let the user disable selected features normally supported by the
device. This makes it possible to work around possible driver or
hardware bugs if the feature in question doesn't work as intended
for whatever reason.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Felix Rubinstein <felixru@gmail.com>
In this code section the final S of CONFIG_MODULES was missed making
the whole check useless
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PCI config space bin_attr read handler has a hardcoded CAP_SYS_ADMIN
check to verify privileges before allowing a user to read device
dependent config space. This is meant to protect from an unprivileged
user potentially locking up the box.
When assigning a PCI device directly to a guest with libvirt and KVM,
the sysfs config space file is chown'd to the unprivileged user that
the KVM guest will run as. The guest needs to have full access to the
device's config space since it's responsible for driving the device.
However, despite being the owner of the sysfs file, the CAP_SYS_ADMIN
check will not allow read access beyond the config header.
With this patch we check privileges against the capabilities used when
openining the sysfs file. The allows a privileged process to open the
file and hand it to an unprivileged process, and the unprivileged process
can still read all of the config space.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The problem. When implementing a network namespace I need to be able
to have multiple network devices with the same name. Currently this
is a problem for /sys/class/net/*, /sys/devices/virtual/net/*, and
potentially a few other directories of the form /sys/ ... /net/*.
What this patch does is to add an additional tag field to the
sysfs dirent structure. For directories that should show different
contents depending on the context such as /sys/class/net/, and
/sys/devices/virtual/net/ this tag field is used to specify the
context in which those directories should be visible. Effectively
this is the same as creating multiple distinct directories with
the same name but internally to sysfs the result is nicer.
I am calling the concept of a single directory that looks like multiple
directories all at the same path in the filesystem tagged directories.
For the networking namespace the set of directories whose contents I need
to filter with tags can depend on the presence or absence of hotplug
hardware or which modules are currently loaded. Which means I need
a simple race free way to setup those directories as tagged.
To achieve a reace free design all tagged directories are created
and managed by sysfs itself.
Users of this interface:
- define a type in the sysfs_tag_type enumeration.
- call sysfs_register_ns_types with the type and it's operations
- sysfs_exit_ns when an individual tag is no longer valid
- Implement mount_ns() which returns the ns of the calling process
so we can attach it to a sysfs superblock.
- Implement ktype.namespace() which returns the ns of a syfs kobject.
Everything else is left up to sysfs and the driver layer.
For the network namespace mount_ns and namespace() are essentially
one line functions, and look to remain that.
Tags are currently represented a const void * pointers as that is
both generic, prevides enough information for equality comparisons,
and is trivial to create for current users, as it is just the
existing namespace pointer.
The work needed in sysfs is more extensive. At each directory
or symlink creating I need to check if the directory it is being
created in is a tagged directory and if so generate the appropriate
tag to place on the sysfs_dirent. Likewise at each symlink or
directory removal I need to check if the sysfs directory it is
being removed from is a tagged directory and if so figure out
which tag goes along with the name I am deleting.
Currently only directories which hold kobjects, and
symlinks are supported. There is not enough information
in the current file attribute interfaces to give us anything
to discriminate on which makes it useless, and there are
no potential users which makes it an uninteresting problem
to solve.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move complete knowledge of namespaces into the kobject layer
so we can use that information when reporting kobjects to
userspace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_del and device_rename were modified to use
sysfs_delete_link and sysfs_rename_link respectively to ensure
when these operations happen on devices whose classes
are in namespace directories they work properly.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent udev versions probe loop devices for filesystems meaning that
the /dev/disk hierarchy may contain useful entries such as
$ ls -l /dev/disk/by-label/Fedora-12-x86_64-Live
lrwxrwxrwx 1 root root 11 Mar 11 13:41 /dev/disk/by-label/Fedora-12-x86_64-Live -> ../../loop0
Unfortunately, no "change" uevent is generated when the loop device is
detached so the symlink persists. Additionally, no "change" uevent is
guaranteed to be generated when attaching an fd or changing capacity.
For example, user space could open the loop device O_RDONLY (in fact,
recent util-linux-ng does this) so udev's OPTIONS+="watch" machinery may
not trigger the "change" uevent.
This patch ensures that the "change" uevent is generated in all of
these cases. As a result, the /dev/disk hierarchy works as expected
for loop devices.
Signed-off-by: David Zeuthen <davidz@redhat.com>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While device_shutdown() walks through devices_kset to shutdown all
devices, device unplug events may race to shutdown individual devices.
Specifically, sd_shutdown(), on behalf of fc_starget_delete(), has
been observed deleting devices during device_shutdown()'s list
traversal. So we factor out list_for_each_entry_safe_reverse(...) in
favor of while (!list_empty(...)).
Signed-off-by: Hugh Daschbach <hdasch@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fw_id has the same life time as firmware_priv so it makes sense to move
it into firmware_priv structure instead of allocating separately.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Split builtin firmware handling into separate functions to clean up the
main body of code.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Do not create 'timeout' attribute manually, let driver core do it for us.
This also ensures that attribute is cleaned up properly.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we use request_firmware_nowait(), userspace may
not want to answer negatively right away when for
example it is answering from an initrd only, but
with request_firmware() it has to in order to not
delay the kernel boot until the request times out.
This allows userspace to differentiate between the
two in order to be able to reply negatively to async
requests only when all filesystems have been mounted
and have been checked for the requested firmware file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The conversion of device->sem to device->mutex resulted in lockdep
warnings. Create a novalidate class for now until the driver folks
come up with separate classes. That way we have at least the basic
mutex debugging coverage.
Add a checkpatch error so the usage is reserved for device->mutex.
[ tglx: checkpatch and compile fix for LOCKDEP=n ]
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The semaphore is semantically a mutex. Convert it to a real mutex and
fix up a few places where code was relying on semaphore.h to be included
by device.h, as well as the users of the trylock function, as that value
is now reversed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When runtime PM for platform_bus was added, it allowed for platforms
to customize the runtime PM methods since they are defined as weak
symbols.
This patch allows platforms to also extend the system PM methods with
custom hooks so runtime PM and system PM extensions can be managed
together by custom platform-specific code.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Magnus Damm <damm@opensource.se>
Cc: Rafael Wysocki <rjw@sisk.pl>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make devtmpfs available on (embedded) configurations without SHMEM/TMPFS,
using ramfs instead.
Saves ~15KB.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
kasprintf combines kmalloc and sprintf, and takes care of the size
calculation itself.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression a,flag;
expression list args;
statement S;
@@
a =
- \(kmalloc\|kzalloc\)(...,flag)
+ kasprintf(flag,args)
<... when != a
if (a == NULL || ...) S
...>
- sprintf(a,args);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1351) removes an unnecessary and unwanted assignment
from device_initialize(). The wakeup flags are set to 0 along with
everything else when the device structure is allocated, so we don't
need to do it again. Furthermore, the subsystem might already have
set these flags to their correct values; we don't want to override it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fix a potential race condition in the driver_bound() function
in the file driver/base/dd.c.
The broadcast of the BUS_NOTIFY_BOUND_DRIVER notifier should be done
after adding the new device to the driver list. Otherwise notifier
listener will fail if they use functions like usb_find_interface().
The patch is against kernel 2.6.33. Please merge it.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The messages from _request_firmware() informing that firmware is
being requested or built-in firmware is going to be used are printed
at KERN_INFO, which produces lots of noise on systems with huge
numbers of AMD CPUs. Reduce the level of these messages to
KERN_DEBUG to get rid of that noise.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix memory leak introduced by the patch 6e03a201bb:
firmware: speed up request_firmware()
1. vfree won't release pages there were allocated explicitly and mapped
using vmap. The memory has to be vunmap-ed and the pages needs
to be freed explicitly
2. page array is moved into the 'struct
firmware' so that we can free it from release_firmware()
and not only in fw_dev_release()
The fix doesn't break the firmware load speed.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Singed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without CONFIG_CPUMASK_OFFSTACK, simply inverting cpu_online_mask leads
to CPUs beyond nr_cpu_ids to be displayed twice and CPUs not even
possible to be displayed as offline.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
REMOTE_DEBUG does already appear in 2.2 kernel sources but didn't
appear as a config Option in the initial git import 2.6.12-rc. It's
currently just used in one single place of the linux kernel and should
probably be dropped totally
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes it return -ENODEV if we run out of empty slots in the
probe function. It's unlikely to happen, but it makes the static
checkers happy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the resource_size function instead of manually calculating the
resource size. This actually fixes an off-by-one error.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Comment was not updated when tty_insert_flip_string was generalised.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add an UART driver for the UART component available as a SOPC (System on
Programmable Chip) component for Altera FPGAs.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add an UART driver for the JTAG UART component available as a SOPC
(System on Programmable Chip) component for Altera FPGAs.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a problem in early versions of the FPGA IP.
In certain situations the IP reports that the FIFO is empty, but a byte is
still clocked out. If a flush is done at that point the currently clocked
byte is canceled.
This causes incompatibilities with the upper layers when a port is closed,
it waits until the FIFO is empty and then closes the port. During close
the FIFO is flushed -> the last byte is not sent properly.
Now the FIFO is only flushed if it is reported to be non-empty. Which
makes the currently clocked out byte to finish.
[akpm@linux-foundation.org: fix build]
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CTS is a read only bit and we are to stop signal RTS if modem line
TIOCM_RTS is not set.
Thanks for suggestions by Richard Röjfors.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Byte accesses for I/O devices in Xilinx IP is going to be less
desired in the future such that the driver is being changed to
use 32 bit accesses.
This change facilitates using the uartlite IP over a PCIe bus
which only allows 32 bit accesses.
Signed-off-by: John Linn <john.linn@xilinx.com>
Tested-by: Michal Simek <monstr@monstr.eu>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
n_gsm uses skb functions, so it should depend on NET.
n_gsm.c:(.text+0x123d49): undefined reference to `skb_dequeue'
n_gsm.c:(.text+0x123d98): undefined reference to `kfree_skb'
n_gsm.c:(.text+0x123e1e): undefined reference to `skb_pull'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add an implementation of GSM 0710 MUX. The implementation currently supports
- Basic and advanced framing (as either end of the link)
- UI or UIH data frames
- Adaption layer 1-4 (1 and 2 via tty, 3 and 4 as skbuff lists)
- Modem and control messages including the correct retry process
- Flow control
and exposes the MUX channels as a set of virtual tty devices including modem
signals. This is an experimental driver.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The BF54xM procs imply the related BF54x define, so no need to check both.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the SPORT MMR defines have been unified, switch over to it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rather than always turn on the SPORT TX interrupt, only do it when we've
actually queued up data for transmission. This avoids useless interrupt
processing.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These were all copied over from the Blackfin UART driver, but they don't
make sense here because these bits are all specific to the Blackfin UART.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Need to initialize the SPORT state rather than using random memory.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Common serial API says we need to grab the port lock before modifying
the port state to prevent inconsistent state between threads.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some people need flow control on their ports, so now boards can support
that via any GPIOs.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clarifies command line set up for devices between consoles and early
devices.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver doesn't care about this, but the common serial core wants it.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All the resources are in the boards files now.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The waiting loop to stop SPORT TX from TX interrupt is too long. This may
block the SPORT RX interrupts and cause the RX FIFO to overflow. So, do
stop sport TX only after the last char in TX FIFO is moved into the shift
register.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We cannot let a 32-bit RX FIFO read be interrupted otherwise a fake RX
underflow error might be generated.
URL: http://blackfin.uclinux.org/gf/tracker/5145
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.infradead.org/mtd-2.6: (154 commits)
mtd: cfi_cmdset_0002: use AMD standard command-set with Winbond flash chips
mtd: cfi_cmdset_0002: Fix MODULE_ALIAS and linkage for new 0701 commandset ID
mtd: mxc_nand: Remove duplicate NAND_CMD_RESET case value
mtd: update gfp/slab.h includes
jffs2: Stop triggering block erases from jffs2_write_super()
jffs2: Rename jffs2_erase_pending_trigger() to jffs2_dirty_trigger()
jffs2: Use jffs2_garbage_collect_trigger() to trigger pending erases
jffs2: Require jffs2_garbage_collect_trigger() to be called with lock held
jffs2: Wake GC thread when there are blocks to be erased
jffs2: Erase pending blocks in GC pass, avoid invalid -EIO return
jffs2: Add 'work_done' return value from jffs2_erase_pending_blocks()
mtd: mtdchar: Do not corrupt backing device of device node inode
mtd/maps/pcmciamtd: Fix printk format for ssize_t in debug messages
drivers/mtd: Use kmemdup
mtd: cfi_cmdset_0002: Fix argument order in bootloc warning
mtd: nand: add Toshiba TC58NVG0 device ID
pcmciamtd: add another ID
pcmciamtd: coding style cleanups
pcmciamtd: fixing obvious errors
mtd: chips: add SST39WF160x NOR-flashes
...
Trivial conflicts due to dev_node removal in drivers/mtd/maps/pcmciamtd.c
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: misc comment fixes
UBI: fix s/then/than/ typos
UBI: init even if MTD device cannot be attached, if built into kernel
UBI: remove reboot notifier