The GMAC (gigabit ethernet controller) supports RGMII to connect to
the ethernet PHY, for gigabit network speeds.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 has the same GMAC found on the A31 SoC.
Add a device node, and an alias for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 has the same DWMAC hardware as on earlier Allwinner SoCs. The
accompanying GMAC clock register has been moved into the "System
Control" area.
Add a clock node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Cubieboard 4 has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs. All pin-banks that
have supply rails are accounted for. PN pin-bank does not have a
supply rail.
Also remove any "regulator-always-on" properties from regulators that
were only marked to provide pin-bank power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 Optimus has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs. All pin-banks that
have supply rails are accounted for. PN pin-bank does not have a
supply rail.
Also remove any "regulator-always-on" properties from regulators that
were only marked to provide pin-bank power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The DC1SW output from the AXP809 is unused. Unused regulators should
still be listed so as to be considered to be fully constrained.
Fixes: aa4a27bc81 ("ARM: dts: sun9i: a80-optimus: Add AXP809 PMIC device node and regulators")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds dt-binding documentation of cpu for Mediatek MT8183.
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fix apb, cbus, hiu and periph regions which are not aligned
with the documentation and the information provided by Amlogic
Fixes: 9c8c52f7cb ("arm64: dts: meson-g12a: add initial g12a s905d2 SoC DT support")
Cc: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The USB controllers need to be associated with their respective IOMMU
bank, so define this on the dwc3 nodes.
Also add dma-ranges to the qcom-dwc3 nodes to make the bus' DMA mask
propagate to the dwc3 controller instances.
Fixes: 4429e57567 ("arm64: dts: sdm845: Add node for arm,mmu-500")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
With apps_smmu initializing the SMMU we must specify iommus property for
the sdhc controller.
Fixes: 4429e57567 ("arm64: dts: sdm845: Add node for arm,mmu-500")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Since all cpus in the big and little clusters, respectively, are in the
same frequency domain, use all of them for mitigation in the
cooling-map. We end up with two cooling devices - one each for the big
and little clusters.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The databook clearly states that the MSI IRQ (msi_ctrl_int) is a level
triggered interrupt.
The msi_ctrl_int will be high for as long as any MSI status bit is set,
thus the IRQ type should be set to IRQ_TYPE_LEVEL_HIGH, causing the
IRQ handler to keep getting called, as long as any MSI status bit is set.
A git grep shows that ipq4019 is the only SoC using snps,dw-pcie that has
configured this IRQ incorrectly.
Not having the correct IRQ type defined will cause us to lose interrupts,
which in turn causes timeouts in the PCIe endpoint drivers.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The apcs node has #clock-cells = <0>, which means that those who
references it should specify 0 arguments.
The apcs reference in the cpu node incorrectly specifies an argument,
remove this bogus argument.
Fixes: 65afdf4583 ("arm64: dts: qcom: msm8916: Add CPU frequency scaling support")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The cpu_lp clock property is only needed when the CPUfreq driver
supports CPU cluster switching. But it was not a design for this driver
and it didn't handle that as well. So removing this property.
Cc: devicetree@vger.kernel.org
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra124 cpufreq driver works only with DFLL clock, which is a
hardware-based frequency/voltage controller. The driver doesn't need to
control the regulator itself. Hence remove that.
Cc: devicetree@vger.kernel.org
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add Tegra210 support for DFLL clock.
Cc: devicetree@vger.kernel.org
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add new properties to configure the DFLL PWM regulator support.
Cc: devicetree@vger.kernel.org
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Starting with commit 8947e396a8 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Libre Computer ALL-H3-CC H5 is one of the few boards that can have
its eMMC run at HS-DDR speed mode. Mark it as such.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
On these A64 devices, the DC input jacks are wired to the ACIN pins of
the PMIC, which is represented by the AC power supply. With the
exception of the Nanopi A64, all devices include LiPo batteries or have
connectors for them, which are represented by the battery power supply.
Enable these power supplies in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Ensure the PCIe endpoint card reset that is toggled by the PCIe
controller itself is muxed correctly on the EspressoBin.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
One pin can be muxed as PCIe endpoint card reset.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
On Marvell Armada 3700 SoCs there are two USB2 UTMI PHYs. They are
both very similar but only one has OTG/charging capabilities.
Because there are USB host registers and PHY registers mixed in a
single area, a system controller is also created and referenced from
both the USB host node and the PHY node.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The specification splits the USB2 memory region into three sections:
1/ 0xD005E000-0xD005EFFF: USB2 Host Controller Registers
2/ 0xD005F000-0xD005F7FF: USB2 UTMI PHY Registers
3/ 0xD005F800-0xD005FFFF: USB2 Host Miscellaneous Registers
Section 1/ belongs to the USB2 node but section 2/ belongs to the UTMI
PHY node. Section 3/ can be accessed by both the USB controller and
the PHY because of the miscaellaneous nature of the registers inside
so a specific node will be created to cover the area and a handle to
it will be added in both the USB controller and the PHY node.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The SATA IP get its clock from the north-bridge.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fix the SATA IP memory area which is only 0x178 bytes long (from
Marvell A3700 specification). Actually, starting from the offset
0xe0178, there is an area dedicated to the COMPHY driver.
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add interrupt properties in the thermal node as well as a critical trip
point in the thermal-zone.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add interrupt properties in the thermal node as well as a critical trip
point in the thermal-zone.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This reverts commit abd7d0972a. This
change was already partially reverted by John Stultz in
commit 9c6d26df1f ("arm64: dts: hikey: Fix eMMC corruption regression").
This change appears to cause controller resets and block read failures
which prevents successful booting on some hikey boards.
Cc: Ryan Grachek <ryan@edited.us>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: stable <stable@vger.kernel.org> #4.17+
Signed-off-by: Alistair Strachan <astrachan@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Somewhere along recent changes to power control of the wl1835, power-on
became very unreliable on the hikey, failing like this:
wl1271_sdio: probe of mmc2:0001:1 failed with error -16
wl1271_sdio: probe of mmc2:0001:2 failed with error -16
After playing with some dt parameters and comparing to other users of
this chip, it turned out we need some power-on delay to make things
stable again. In contrast to those other users which define 200 ms, the
hikey would already be happy with 1 ms. Still, we use the safer 10 ms,
like on the Ultra96.
Fixes: ea45267873 ("arm64: dts: hikey: Fix WiFi support")
Cc: <stable@vger.kernel.org> #4.12+
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Regarding the 'gpio_keys' device node a dtc reports a couple of
warnings:
Warning (avoid_unnecessary_addr_size): /gpio_keys: unnecessary
#address-cells/#size-cells without "ranges" or child "reg" property
Warning (unit_address_vs_reg): /gpio_keys/button@21: node has
a unit name, but no reg property
The change fixes these issues and adds empty lines between adjacent
children device nodes. The device node itself is renamed by substituting
an underscore by hyphen to follow the standard naming convention
of device tree nodes.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds a unit address to memory device node, the issue was
reported as a unit_address_vs_reg warning by dtc.
Root device node properties #address-cells and #size-cells were
removed as inherited from lpc32xx.dtsi.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds a unit address to memory device node, the issue was
reported as a unit_address_vs_reg warning by dtc.
Root device node properties #address-cells and #size-cells were
removed as inherited from lpc32xx.dtsi.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds description of Sharp LQ035Q7DB03 3.5" 320x240 TFT panel,
which is connected to Phytec phyCORE-LPC3250 board, ARM PrimeCell PL111
LCD controller on NXP LPC3250 SoC gets its configuration appropriately
to support graphics output to the panel.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The originally added 'regulators' device node has a number of flaws,
to name a few its children has unit addresses but no reg properties,
the regulators are not captured by a device driver due to a missing
'simple-bus' compatible, the regulator names are selected by killing
either alphabetical order or device node grouping property.
The change removes 'regulators' device node and renames the regulators
and labels.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The fixed voltage regulator on Phytec phyCORE-LPC3250 board, which
supplies SD/MMC card's power, has a constant output voltage level
of either 3.15V or 3.3V, the actual value depends on JP4 position,
the power rail is referenced as VCC_SDIO in the board hardware manual.
Fixes: d06670e962 ("arm: dts: phy3250: add SD fixed regulator")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The originally added ARM PrimeCell PL111 clocks property misses
the required "clcdclk" clock, which is the same as a clock to enable
the LCD controller on NXP LPC3230 and NXP LPC3250 SoCs.
Fixes: 93898eb775 ("arm: dts: lpc32xx: add clock properties to device nodes")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
ARM PrimeCell PL111 LCD controller is found on On NXP LPC3230
and LPC3250 SoCs variants, the original reference in compatible
property to an older one ARM PrimeCell PL110 is invalid.
Fixes: e04920d9ef ("ARM: LPC32xx: DTS files for device tree conversion")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
After switching to a new interrupt controller scheme by separating SIC1
and SIC2 from MIC interrupt controller just one SoC keypad controller
was not taken into account, fix it now:
WARNING: CPU: 0 PID: 1 at kernel/irq/irqdomain.c:524 irq_domain_associate+0x50/0x1b0
error: hwirq 0x36 is too large for interrupt-controller@40008000
...
lpc32xx_keys 40050000.key: failed to get platform irq
lpc32xx_keys: probe of 40050000.key failed with error -22
Fixes: 9b8ad3fb81 ("ARM: dts: lpc32xx: reparent SIC1 and SIC2 interrupts from MIC")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
NXP LPC32xx keypad controller requires a clock property to be defined.
The change fixes the driver initialization problem:
lpc32xx_keys 40050000.key: failed to get clock
lpc32xx_keys: probe of 40050000.key failed with error -2
Fixes: 93898eb775 ("arm: dts: lpc32xx: add clock properties to device nodes")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Add support for MYIR Tech MYD-LPC4357 Development Board and
MY-LCD70TP-C 7" TFT LCD module with Innolux AT070TN82 panel.
The board contains quite rich periferals, the list features
NXP LPC4357 SoC, 32 MB SDRAM, 4 MB SPI Flash, audio input/output
interface, LCD panel, micro SD card slot, USB, USB OTG, Ethernet,
2 CAN ports, 4 UARTs, I2C and SPI interfaces routed to external
interface.
More information can be found on http://www.myirtech.com/list.asp?id=422
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix
the following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[vzapolskiy: fixed commit message to pass checkpatch.pl test]
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The following properties:
- regulator-state-enabled
- regulator-state-disabled
- regulator-state-uv
are not valid ones as per
Documentation/devicetree/bindings/regulator/regulator.txt
Fix it by using the correct properties as per the dt bindings.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The following properties:
- regulator-state-enabled
- regulator-state-disabled
- regulator-state-uv
are not valid ones as per
Documentation/devicetree/bindings/regulator/regulator.txt
Fix it by using the correct properties as per the dt bindings.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On rv1108-elgin-r1 board the RK805 VCC5 and VCC6 supplies come from
the BUCK2 regulator at 2.2V, so fix the representation in the
device tree.
While at it, rename it from vdd_cam to vdd_buck2, which is a better
name for the regulator label.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable the gpu node and add the supplying regulator
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This commit enable the hdmi-sound and i2s2 devices needed to have
audio over HDMI on both rock960 and the related ficus board.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add RSC (Resource State Coordinator) provider
dictating network-on-chip interconnect bus performance
found on SDM845-based platforms.
Signed-off-by: David Dai <daidavid1@codeaurora.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
