This patch adds clean up routine to clear the stream registers and
calls this routine before setting up stream registers.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This machine supports HDMI/DP ports so add these ports and its FE and BE
DAIlinks
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have WOV module which should act as DAPM sink, so add that and
its links.
Also rename the refcap to "Wake On Voice" as some user expect to
find this name
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have specific constraints for FE device (48KHz, stereo, 16
bits) and fixups for BE DMIC links (2 or 4 ch), so add those.
Also add one more FE DAIlink for dmiccap
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't support ignore suspend on few devices so remove that.
Also since we support ignore susend on PDM DMIC, add that
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAPM map for DMIC and SSP was not properly done, so fix that up.
Also mark machine as fully routed
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds Skylake I2S machine driver which uses NAU88L25 as anlog codec and
MAX98357A as speakers
Signed-off-by: Rohit Ainapure <rohit.m.ainapure@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the NAU88L25 + MAX98357A machine driver entry into
the machine table
Signed-off-by: Rohit Ainapure <rohit.m.ainapure@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"data" is a u32 pointer so this copies the information to wrong place
entirely.
Fixes: 140adfba52 ('ASoC: Intel: Skylake: Add tlv byte kcontrols')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These need to be signed because they hold negative error codes.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sst_memcpy32() only copied bytes/4 32bits, which means it dropped
the remaining bytes%4 bytes wrongly.
Here add copying those missing bytes, first to a 32bits tmp, and
then write the tmp to 32bits iomem.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If driver received a message that it can't handle, it won't
clear the corresponding bit and unmask interrupt, this may
lock the IRQ and DSP can't send message anymore.
To fix the issue, we should Always update IMRX after IPC.
Here we always clear the DONE/BUSY bit and unmask the IRQ
source, even when IPC failures have occurred previously.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Modified-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should only add ignore suspend flag for some DAIs and not all.
This patches removes it from the DAIs where we do not support
this
It also marks the endpoints for which ignore_suspend should be
enabled
Signed-off-by: Praveen Diwakar <praveen.diwakar@intel.com>
Signed-off-by: Vunny Sodhi <vunnyx.sodhi@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of the usecases can be marked as 'ignore_suspend' by
machine. For these on suspend we should keep audio controller
ON by saving the state and not suspending the device
For this we need to maintain a counter for these streams and be
active on suspend when such a stream is opened.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DAPM Machine map for machine was not specifying the paths
correctly.
The correct order should be:
"DMIC01 Rx" (SoC DMIC BE), connected to "DMIC AIF" (DMic Codec
AIF) and then "DMic" (DMic codec Input) connected to "SoC DMIC"
(Machine DMIC MIC Widget)
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since in Skylake we support another DAI for DMIC quad capture,
add a dailink for this as well. Also specify constrains for DMIC
FE devices and fixup for DMIC BEs
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a module is ON then we should read the module parameters from
DSP rather than driver cached values
Signed-off-by: Omair M Abdullah <omair.m.abdullah@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For messages which have larger payload than mailbox data, we need
to split the payload using set of messages containing mailbox
size as payload.
For sending such payload we already support LARGE_CONFIG_SET
IPCs and now to query such payload add LARGE_CONFIG_GET IPC
Signed-off-by: Mousami Jana <mousami.janax@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SKL actual mailbox size is 0x10000 and initial values were 0x800,
so update these accordingly
Signed-off-by: Omair M Abdullah <omair.m.abdullah@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Module initialization parameter data can be set by
- INIT_INSTANCE IPC by using the default value
- SET_PARAMS immediately after INIT_INSTANCE
- SET_PARAMS data from kcontrol values set
this patch add param type to identify the parameters
has to be sent to DSP.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mic select is a DSP module which is used to select one or many
inputs to form an output. This is useful to select data
selectively from PDM input and hence the name. This module is of
generic module type.
This patch adds support to add and configure Mic select module in
firmware topology.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A module can require extra memory for processing, like audio
algorithms. The memory for these modules needs to be represented
in base module configuration and passed to DSP on init, so add
the memory pages as a field in widget data
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A module is loaded when the path consisting the module is opened.
The module binary(ies) is loaded from file system and cached in
kernel memory for future use. This is downloaded to DSP using DMA
and invoking Load module IPCs
This patch adds support for load/unload module IPCs, DMAing
modules and manging the modules
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds tlv bytes topology control creation and control load to
initialize kcontrol data. And this also adds the callbacks for
the these tlv byte kcontrols
Signed-off-by: Mythri P K <mythri.p.k@intel.com>
Signed-off-by: Divya Prakash <divya1.prakash@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support to configure module parameter during module
initialization or after module init using set module param
required by the DSP firmware sequence.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some DSP modules has user configurable parameters, which are
required by some modules at module initialization.
To configure the module algorithm parameter during initialization
we add helpers here
Signed-off-by: Divya Prakash <divya1.prakash@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some DSP modules have user configurable parameters. These
parameters are required by modules in the following scenario
- during initialization
- after initialization using set parameter
This patch adds helper routine to set module parameters using
large config set IPC message and removes params to be passed as
init module routine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Skylake we can support upton 4DMICs on the PDM port, so update
the PCM capabilities accordingly
Also add a new DAI for DMIC pin which can be used for getting raw
DMIC data
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MCPS is freed first thing in pmd events but non memory. So if
we face error during teardown we leak this mem, so move the code
up
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds polling of CLDMA stream run bit when set
to confirm the HW reports the same value.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds pcm capability to support 16/8k rates and 32 bit formats
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Module hw param fixup will change the valid bit depth based
on the fixup flag. If valid bit depth changes, need to set
the bit depth according to valid bit depth. This patch
fixes this issue of updating bit depth correctly.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
PCM prepare callbacks can be called multiple times. During S3
the stream registers will be reset when Controller is reset.
When stream is resumed, these stream registers needs to reconfigured.
This patch removes the check in prepare callback() if stream already
prepared, which will allow reconfiguring of stream registers and also
decouple stream when stream is resumed to route audio via DSP.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The previous commit ef3e199a49 ("ASoC: Intel: sst: only use
sst-firmware when DW DMAC is available") does not fix the 0day
building errors thoroughly:
sound/built-in.o: In function 'dw_dma_remove'
sound/built-in.o: In function 'dw_dma_probe'
Here we fallback to select sst-firmware only when DW DMAC
is built-in selected. We may need to refactor sst common
driver and split DW related codes to platform driver, but
ATM, this fallback may be the smallest fix.
Please be noticed that after applying this patch, we may
need select DW DMAC manually in DMA driver menu, before
we can prompt and select HSW/BDW and old BYT machines.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Skylake driver uses snd_dma_buffer for data and buffer, these are variables
and not pointer so do not test field addresses.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"data" is always NULL in this function. I think we should be passing
"&data" to sst_prepare_and_post_msg() instead of "data".
Fixes: 3d9ff34622 ('ASoC: Intel: sst: add stream operations')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Dinesh Mirche <dinesh.mirche@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound card rtd was an array and was updated to a list so update
the driver to use a list
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PM ops are required so that DAPM will suspend and resume the DSP
pipelines properly
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In ref configuration for Skylake, we support only 16bit, 48KHz,
stereo audio, so specify these as constrains for the devices
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the below warning form smatch and makes the
skl_tplg_bind_sinks take the next sink as argument which is true
when the current sink is valid
sound/soc/intel/skylake/skl-topology.c:453 skl_tplg_bind_sinks()
error: we previously assumed 'sink' could be null (see line 452)
sound/soc/intel/skylake/skl-topology.c
451
452 if (!sink)
^^^^
New check. Reversed?
453 return skl_tplg_bind_sinks(sink, skl, src_mconfig);
^^^^ This is
dereferenced inside the function.
454
455 return 0;
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When downloading the firmware/module, if the ring buffer boundary
is reached, we need to wrap to the zeroth position. On next copy
we need to copy till end of buffer and the remaining buffer needs
to be copied from zeroth position.
In this case copy was not handled correctly when wrap condition
is reached which caused invalid data to be copied resulting in
invalid hash failure.
This patch fixes the issue by handling copy at the boundary
condition correctly.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sometimes firmware D3 IPC fails causing firmware to be in invalid
state. To recover we need to reset the DSP and then shut it down,
so don't return on error and continue resetting to recover.
On D0, firmware will be redownloaded and DSP will be back in
clean state
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During firmware download, dma buffers are allocated in prepare
and never freed on clean up. This patch frees the allocated dma
buffer in cldma controller clean up.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we call _skl_resume which also initializes the chip we no
need to call these explicitly, so remove the duplication
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For HDA codecs WAKEENABLE bit is to programmed if codec event
change has to wake the system when suspended.
In skylake I2S systems which are currently supported we have
only HDMI codec, which doesn't use this capability to detect a
HDMI connect/ disconnect event. HDMI HDA codec uses display
interface to detect connect/disconnect event.
This patch removes the WAKEBIT enabling during device D0/D3 as
this seems to cause spurious wakes on the system
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASoC core already does pm_runtime_get/put in the core before
opening/closing the devices.
So we do not need to do this is driver, hence remove
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds skl_nau8825_ssn4567_i2s machine driver into
machine table
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
