There are a lot of places where sequences of space/tabs are
found. Get rid of all spaces before tabs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The 'irq' member of the vdoa_data struct is only used inside probe,
so there is no need for it. Use a local variable 'ret' instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The mvcol buffer needs to be placed behind the chroma plane(s) when
decoding MPEG-4, same as for the h.264 decoder. Use the real offset
with the required rounding.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The MPEG-4 decoder mvcol buffer was registered, but its size not added
to a frame buffer allocation. This could cause the decoder to write past
the end of the allocated buffer for large frame sizes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We need internal frames to be rounded up to full macroblocks for MPEG-4
decoding as well.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since bytesperline always fulfills VDOA width requirements, detile the
whole buffer instead of limiting to visible width. This stops TRY_FMT
from returning -EINVAL for YUYV capture buffers that are not a multiple
of 16 wide.
An alternative would be to always round up width to stride, as we report
the valid image rectange via G_SELECTION (V4L2_SEL_TGT_COMPOSE_DEFAULT),
but that would require all applications to handle the compose default
rectangle properly.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current driver implementation expects at least one buffer on
all queues to start streaming. Properly signal this to the vb2
core, to avoid confusion when streamon is racing with qbuf.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to i.MX VPU API Reference Manuals the MJPG video codec is
referenced to by number 7, not 3.
Also Philipp pointed out that this value is only meant to fill in
CMD_ENC_SEQ_COD_STD for encoding, only on i.MX53. It was never written
to any register, and even if defined correctly, wouldn't be needed
for i.MX6.
So avoid confusion and remove this definition.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=d9nT
-----END PGP SIGNATURE-----
Merge tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation for digital TV (both kAPI and uAPI) are now in sync
with the implementation (except for legacy/deprecated ioctls). This
is a major step, as there were always a gap there
- New sensor driver: imx274
- New cec driver: cec-gpio
- New platform driver for rockship rga and tegra CEC
- New RC driver: tango-ir
- Several cleanups at atomisp driver
- Core improvements for RC, CEC, V4L2 async probing support and DVB
- Lots of drivers cleanup, fixes and improvements.
* tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (332 commits)
dvb_frontend: don't use-after-free the frontend struct
media: dib0700: fix invalid dvb_detach argument
media: v4l2-ctrls: Don't validate BITMASK twice
media: s5p-mfc: fix lockdep warning
media: dvb-core: always call invoke_release() in fe_free()
media: usb: dvb-usb-v2: dvb_usb_core: remove redundant code in dvb_usb_fe_sleep
media: au0828: make const array addr_list static
media: cx88: make const arrays default_addr_list and pvr2000_addr_list static
media: drxd: make const array fastIncrDecLUT static
media: usb: fix spelling mistake: "synchronuously" -> "synchronously"
media: ddbridge: fix build warnings
media: av7110: avoid 2038 overflow in debug print
media: Don't do DMA on stack for firmware upload in the AS102 driver
media: v4l: async: fix unregister for implicitly registered sub-device notifiers
media: v4l: async: fix return of unitialized variable ret
media: imx274: fix missing return assignment from call to imx274_mode_regs
media: camss-vfe: always initialize reg at vfe_set_xbar_cfg()
media: atomisp: make function calls cleaner
media: atomisp: get rid of storage_class.h
media: atomisp: get rid of wrong stddef.h include
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kasprintf() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
platform_get_resource() may fail and in this case a NULL dereference
will occur.
Prevent this from happening by returning an error on
platform_get_resource() failure.
Fixes: b0444f18e0 ("[media] coda: add i.MX6 VDOA driver")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The on-chip SRAM of i.MX6S is only 128 KiB. 4 KiB of that are allocated
for suspend to RAM since commit df595746fa ("ARM: imx: add suspend in
ocram support for i.mx6q"). Reduce the requested IRAM size to 124 KiB to
avoid an allocation failure that causes the coda driver to not use the
SRAM at all.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
coda_command_sync calls coda_command_async, which writes the
bit_stream_param context variable into the BIT_STREAM_PARAM register,
overwriting the previously set value during coda_start_decoding. Instead
of writing to the register, set bit_stream_param to ensure that the
decoder sequence init command is executed with the escape flag set.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Disabling the BWB works around hangups observed while decoding. Since no
issues have been observed while encoding, and disabling BWB also reduces
encoding performance, reenable it for encoding.
Fixes: 89ed025d5c ("[media] coda: disable BWB for all codecs on CODA 960")
Reported-by: Ian Arkver <ian.arkver.dev@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Ian Arkver <ian.arkver.dev@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If an encoder stop command is issued after the output queue has already
stopped streaming, the qsequence counter has been reset to 0. Always
wake up the capture queue if the output queue is not streaming.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Explicitly set MPEG-4 encoder class register instead of relying on the
default value of 0.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This fixes visual artifacts in the first macroblock row of encoded
MPEG-4 video output caused by 8 additional lines of luma data leaking
into the chroma planes of the internal reference framebuffers: the
buffer size is rounded up to a multiple of 16x16 macroblock size, same
as for the h.264 encoder.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Set the field of destination buffers properly.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CodaDx6 only accepts GOP sizes up to 60 frames, but CODA960 can handle
up to 99 frames. If we disable automatic I frame generation altogether
by setting GOP size to 0, we can let an application produce arbitrarily
large I frame intervals using the V4L2_CID_MPEG_VIDEO_FORCE_KEY_FRAME
control.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This smatch warning:
coda/coda-common.c:706 coda_s_fmt() warn: missing break? reassigning 'ctx->tiled_map_type'
can be silenced by moving the ctx->tiled_map_type assignment into the
breakout condition. That way the field is not reassigned when falling
through to the next switch statement.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CODA7541 supports H.264 BP level 3/3.1 and MPEG-4 SP level 5/6.
CODA960 supports H.264 BP level 4.0 and MPEG-4 SP level 5/6.
Implement the necessary profile and level controls to let userspace know
this.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
I would have liked the the picture run timeout error handler to be renamed to
something a bit more descriptive in the original commit fb2be08f8c ("[media]
coda: first step at error recovery").
Somehow v1 [1] was merged instead of v2 [2].
[1] https://patchwork.kernel.org/patch/9663965/
[2] https://patchwork.kernel.org/patch/9774239/
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This fixes a smatch warning:
drivers/media/platform/coda/coda-bit.c:415 coda_alloc_framebuffers()
error: we previously assumed 'ctx->codec' could be null (see line 396)
coda_alloc_framebuffers() is called from coda_start_encoding() and
__coda_start_decoding(). Both dereference ctx->codec before calling
coda_alloc_framebuffers() in lines 935 and 1649, so ctx->codec can not
be NULL.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As long as only one CODA context is running we get alternating device_run()
and wait_for_completion() calls, but when more then one CODA context is
active, other VDOA slots can be inserted between those calls for one context.
Make sure to wait on job completion before running a different context and
before destroying the currently active context.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This implements a simple handler for the case where decode did not finish
sucessfully. This might be helpful during normal streaming, but for now it
only handles the case where the context would deadlock with userspace,
i.e. userspace issued DEC_CMD_STOP and waits for EOS, but after the failed
decode run we would hold the context and wait for userspace to queue more
buffers.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The mvcol buffer needs to be placed behind the chroma plane(s), so
use the real offset including any required rounding.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
That way we don't have to rely on userspace to inject the headers on IDR
requests, and there is always enough information to start decoding at an
I-frame.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implement the V4L2_CID_MPEG_VIDEO_FORCE_KEY_FRAME control to force IDR
frames. This is useful to implement VFU (Video Fast Update) on RTP
transmissions.
We already force an IDR frame at the beginning of each GOP to work
around a firmware bug on i.MX27, use the same mechanism to service IDR
requests from userspace.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The hardware codec is not colorspace aware. We should trust userspace to
set the correct colorimetry information on the OUTPUT queue and mirror
the exact same setting on the CAPTURE queue.
There is no reason to restrict colorspace to JPEG or REC709 only. Also,
set the default colorspace, as returned by calling VIDIOC_TRY/S_FMT with
V4L2_COLORSPACE_DEFAULT, initially.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As of commit bb475230b8 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to
describe optional, non-present reset controls.
This allows to return errors from devm_reset_control_get_optional
without special cases and to call reset_control_reset unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The h.264 standard allows up to 16 reference frame for the high profile
and we need one additional internal framebuffer when the VDOA is in use.
Lift the current maximum of 8 internal framebuffers to allow playback
of those video streams.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
TRY_FMT already disables the YUYV format if the VDOA is not available.
ENUM_FMT must do the same.
Fixes: d40e98c13b ("[media] coda: support YUYV output if VDOA is used")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The call to v4ls_m2m_get_vq is only used to get the return value
which is not being used, so it appears to be redundant and can
be removed.
Detected with CoverityScan, CID#1420674 ("Useless call")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drivers/media/platform/coda/coda-common.c: In function ‘coda_alloc_aux_buf’:
./include/linux/kern_levels.h:4:18: warning: format ‘%u’ expects argument of type ‘unsigned int’, but argument 4 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
#define KERN_SOH "\001" /* ASCII Start Of Header */
^
./include/media/v4l2-common.h:69:9: note: in definition of macro ‘v4l2_printk’
printk(level "%s: " fmt, (dev)->name , ## arg)
^~~~~
./include/linux/kern_levels.h:10:18: note: in expansion of macro ‘KERN_SOH’
#define KERN_ERR KERN_SOH "3" /* error conditions */
^~~~~~~~
./include/media/v4l2-common.h:72:14: note: in expansion of macro ‘KERN_ERR’
v4l2_printk(KERN_ERR, dev, fmt , ## arg)
^~~~~~~~
drivers/media/platform/coda/coda-common.c:1341:3: note: in expansion of macro ‘v4l2_err’
v4l2_err(&dev->v4l2_dev,
^~~~~~~~
Hans wrote a similar patch, but it was fold with a Kconfig change.
So, I opted to keep my version.
Signed-off-by Hans Verkuil <hans.verkuil@cisco.com>
Acked-by Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some vars are not used, as warned by gcc:
drivers/media/platform/coda/coda-common.c: In function 'coda_buf_is_end_of_stream':
drivers/media/platform/coda/coda-common.c:816:20: warning: variable 'src_vq' set but not used [-Wunused-but-set-variable]
struct vb2_queue *src_vq;
^~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Recently, an unfinished patch was merged that added a third entry to the
beginning of the array of firmware locations without changing the code
to also look at the third element, thus pushing an old firmware location
off the list.
Fixes: 8af7779f3c ("[media] coda: add Freescale firmware compatibility location")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With reordering enabled, the sequence init in CODA960 firmware requests an
unreasonable number of internal frames for some baseline profile streams.
Disabling the reordering feature manually if baseline streams are detected
fixes this problem.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The bitstream reader needs 512 bytes ready to read to examine the
headers in the first frame. If that frame is too small, prepend it
with a filler NAL.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Keeping buffers filled into the bitstream on a temporary list instead of
immediately calling vb2_buffer_done on each of them immediately allows
start_streaming to correctly decide whether they should be marked as
done or requeued if an error occurs after the bitstream has been filled.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
streamon and streamoff are used as boolean values, not as bitfields.
Therefore, the logical && should be used to combine them.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
I don't know what the BWB unit is, I guess W is for write and one of the
Bs is for burst. All I know is that there repeatedly have been issues
with it hanging on certain streams (ENGR00223231, ENGR00293425), with
various firmware versions, sometimes blocking something related to the
GDI bus or the GDI AXI adapter. There are some error cases that we don't
know how to recover from without a reboot. Apparently this unit can be
disabled by setting bit 12 in the FRAME_MEM_CTRL mailbox register to
zero, so do that to avoid crashes.
Side effects are reduced burst lengths when writing out decoded frames
to memory, so there is an "enable_bwb" module parameter to turn it back
on.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is no need to call v4l2_m2m_try_schedule to kick off draining the
bitstream buffer for the encoder, but we have to wake up the destination
queue in case there are no new OUTPUT buffers to be encoded and userspace
is already polling for new CAPTURE buffers.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The device driver platform is actually written to during registration,
for setting the owner field, so platform_driver_register() does not
take a const pointer:
drivers/media/platform/coda/imx-vdoa.c: In function 'vdoa_driver_init':
drivers/media/platform/coda/imx-vdoa.c:333:213: error: passing argument 1 of '__platform_driver_register' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
module_platform_driver(vdoa_driver);
In file included from drivers/media/platform/coda/imx-vdoa.c:22:0:
include/linux/platform_device.h:199:12: note: expected 'struct platform_driver *' but argument is of type 'const struct platform_driver *'
extern int __platform_driver_register(struct platform_driver *,
^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/platform/coda/imx-vdoa.c: In function 'vdoa_driver_exit':
drivers/media/platform/coda/imx-vdoa.c:333:626: error: passing argument 1 of 'platform_driver_unregister' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
Remove the modifier again.
Fixes: d2fe28feae ("[media] coda/imx-vdoa: constify structs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Freescale provided imx-vpu looks for firmware files under /lib/firmware/vpu
by default. Make coda look there for firmware files to ease the update path.
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
