The following compilation issue popped up moving from v3.10-rc1 to
v3.10-rc6 after merging wireless-testing.
net/wireless/sysfs.c:86:13: error: 'cfg80211_leave_all' defined
but not used [-Werror=unused-function]
The function is only called when CONFIG_PM is enabled. Moving the
function under CONFIG_PM as well.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If it *is* still set when the netdev is being deleted,
then we are about to leak a pointer. Warn and clean up
in that case.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Should help the next person that tries to understand
the bss refcounting logic.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fixes the potential issue that the BSS struct that we use
and later assign to wdev->current_bss is removed from the scan
list while associating.
Also warn when we don't have a BSS struct in connect_result
unless it's from a driver that only has the connect() API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Doing so will allow us to hold the BSS (not just ref it) over the
association process, thus ensuring that it doesn't time out and
gets invisible to the user (e.g. in 'iw wlan0 link'.)
This also fixes a leak in mac80211 where it doesn't always release
the BSS struct properly in all cases where calling this function.
This leak was reported by Ben Greear.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid parsing the original dump message again and again by
allocating a small state struct that is used by the functions
involved in the dump, storing this struct in cb->args[0].
This reduces the memory allocation size as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge mac80211 to avoid conflicts with the nl80211 attrbuf
changes.
Conflicts:
net/mac80211/iface.c
net/wireless/nl80211.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since my commit 3713b4e364 ("nl80211: allow splitting wiphy
information in dumps"), nl80211_dump_wiphy() uses the global
nl80211_fam.attrbuf for parsing the incoming data. This wouldn't
be a problem if it only did so on the first dump iteration which
is locked against other commands in generic netlink, but due to
space constraints in cb->args (the needed state doesn't fit) I
decided to always parse the original message. That's racy though
since nl80211_fam.attrbuf could be used by some other parsing in
generic netlink concurrently.
For now, fix this by allocating a separate parse buffer (it's a
bit too big for the stack, currently 1448 bytes on 64-bit). For
-next, I'll change the code to parse into the global buffer in
the first round only and then allocate a smaller buffer to keep
the data in cb->args.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 6d810f1032
In this way an IBSS station will not use the AUTH messages
to trigger a state reinitialisation anymore.
The behaviour was racy and was not working properly.
It has been introduced to help wpa_supplicant to support
IBSS/RSN, however all the logic is now getting moved into
wpa_s itself which will also be in charge of handling the
AUTH messages thanks to the mgmt frame registration.
If userspace does not register for receiving AUTH frames
then mac80211 will still reply by itself.
At the same time, the auth frame registration counter can be
removed since it is not needed anymore.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[remove unused variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This should make some parts cleaner and is also required for handling
5/10 MHz properly.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is a collection of minor fixes:
* don't allow HT IEs in IBSS for 5/10 MHz
* don't allow HT IEs in Mesh for 5/10 MHz
* don't downgrade from/to 5 and 10 MHz channels
* don't try HT rates for 5 and 10 MHz channels when selecting rates
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add defines for 5 and 10 MHz channel width and fix channel
handling functions accordingly.
Also check for and report the WIPHY_FLAG_SUPPORTS_5_10_MHZ
capability.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[fix spelling in comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of updating the mesh beacon immediately when
requested (which would require the sdata_lock()), defer it
to the mac80211 workqueue.
Fixes yet another deadlock on calling sta_info_flush()
with the sdata_lock() held from ieee80211_stop_mesh(). We
could just drop the sdata_lock() around the
mesh_sta_cleanup() call, but this path is also taken from
several non-locked error paths.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[fix comment position]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
only the attributes are required and not the whole netlink info, as the
function accesses the attributes only anyway. This makes it easier to
parse nested beacon IEs later.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Track the AP's beacon rate in the scan BSS data and in the
interface configuration to let the drivers know which rate
the AP is using. This information may be used by drivers,
in our case to let the firmware optimise beacon RX.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All accesses of the tid_start_tx lock should be protected
by sta->lock if there is any chance that another thread
could still be accessing the sta object.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ben reports that kmemleak is saying TX aggregation TID
structs are leaked. Given his workload, I suspect that
they're leaked because stations are destroyed before
their aggregation sessions get a chance to start. Fix
this by simply freeing structs that are not used yet.
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The order of parameters was mixed up, introduced in commit
"mac80211: improve the rate control API"
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a CAC is running and stop_ap is called (e.g. when hostapd is killed
while performing CAC), the CAC must be aborted immediately.
Otherwise ieee80211_stop_ap() will try to stop it when it's too late -
wdev->channel is already NULL and the abort event can not be generated.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are some APs, notably 2G/3G/4G Wifi routers, specifically the
"Onda PN51T", "Vodafone PocketWiFi 2", "ZTE MF60" and a similar
T-Mobile branded device [1] that erroneously don't include all the
needed information in (re)association response frames. Work around
this by assuming the information is the same as it was in the
beacon or probe response and using the data from there instead.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=58881.
[1] https://bbs.archlinux.org/viewtopic.php?pid=1277305
Note that this requires marking the first ieee802_11_parse_elems()
argument const, otherwise we'd get a compiler warning.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Michal Zajac <manwe@manwe.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In two wiphy dump error cases, most often when the dump allocation
must be increased, the RTNL is leaked. This quickly results in a
complete system lockup. Release the RTNL correctly.
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Users may want to send a frame on the current channel
without specifying it.
This is particularly useful for the correct implementation
of the IBSS/RSN support in wpa_supplicant which requires to
receive and send AUTH frames.
Make mgmt_tx pass a NULL channel to the driver if none has
been specified by the user.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211 passes a NULL channel to mgmt_tx if the frame has
to be sent on the one currently in use by the device.
Make the implementation of mgmt_tx correctly handle this
case
Cc: Nicolas Cavallari <Nicolas.Cavallari@lri.fr>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211 passes a NULL channel to mgmt_tx if the frame has
to be sent on the one currently in use by the device.
Make the implementation of mgmt_tx correctly handle this
case
Cc: brcm80211-dev-list@broadcom.com
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211 passes a NULL channel to mgmt_tx if the frame has
to be sent on the one currently in use by the device.
Make the implementation of mgmt_tx correctly handle this
case. Fail if offchan is required.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[fix RCU locking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I (Johannes) accidentally applied the first version of the patch
("Allow TDLS peer AID to be configured for VHT"). Now apply just
the changes between v1 and v2 to get the AID verification and
prefer the new attribute over the old one.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently mesh uses mandatory rates as the default basic rates. Allow basic
rates to be configured during mesh join. Basic rates are applied only if
channel is also provided with mesh join command.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
[some whitespace fixes, refuse basic rates w/o channel]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The time it takes to see the peer link expire may differ
by a minute since sta_expire() is run once a minute as a
mesh housekeeping task.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a STA has a peer that it hasn't seen any tx activity
from for a certain length of time, the peer link is
expired. This means the inactive STA is removed from the
list of peers and that STA is not considered a peer again
unless it re-peers. Previously, this inactivity time was
always 30 minutes. Now, add it to the mesh configuration
and allow it to be configured. Retain 30 minutes as a
default value.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The patch "cfg80211/mac80211: use cfg80211 wdev mutex in
mac80211" introduced several deadlocks by converting the
ifmsh->mtx to wdev->mtx. Solve these by:
1. drop the cancel_work_sync() in ieee80211_stop_mesh().
Instead make the mesh work conditional on whether the mesh
is running or not.
2. lock the mesh work with sdata_lock() to protect beacon
updates and prevent races with wdev->mesh_id_len or
cfg80211.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently beacon availability upon association is marked by have_beacon
flag of assoc_data structure that becomes unavailable when association
completes. However beacon availability indication is required also after
association to inform a driver. Currently dtim_period parameter is used
for this purpose. Move have_beacon flag to another structure, persistant
throughout a interface's life cycle. Use suitable sematics for beacon
availability indication.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
[fix another instance of BSS_CHANGED_DTIM_PERIOD in docs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_rx_bss_info() deals with dtim_period setting and PS update
when associated. Move all these to another locations cleaning this
function. Also, the current implementation is buggy because when it
calls ieee80211_recalc_ps() bss_conf->dtim_period is notset properly
yet and thus nothing will happen.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The change to use atomic_inc_return() for assigning the wiphy
index made the first wiphy index 1 instead of 0. This is fine,
but we all habitually type "phy0" when we're testing, so make
it go back to 0 instead of 1 by subtracting 1 from the index.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My big locking cleanups caused a problem by registering the
rfkill instance with the RTNL held, while the callback also
acquires the RTNL. This potentially causes a deadlock since
the two locks used (rfkill mutex and RTNL) can be acquired
in two different orders. Fix this by (un)registering rfkill
without holding the RTNL. This needs to be done after the
device struct is registered, but that can also be done w/o
holding the RTNL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
get_reg_request_treatment() returns 0 in one case but is
defined to return an enum, use the proper value REG_REQ_OK.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current internal SME implementation in cfg80211 is
very mixed up with the MLME handling, which has been
causing issues for a long time. There are three things
that the implementation has to provide:
* a basic SME implementation for nl80211's connect()
call (for drivers implementing auth/assoc, which is
really just mac80211) and wireless extensions
* MLME events for the userspace SME
* SME events (connected, disconnected etc.) for all
different SME implementation possibilities (driver,
cfg80211 and userspace)
To achieve these goals it isn't necessary to track the
software SME's connection status outside of it's state
(which is the part that caused many issues.) Instead,
track it only in the SME data (wdev->conn) and in the
general case only track whether the wdev is connected
or not (via wdev->current_bss.)
Also separate the internal implementation to not have
callbacks from the SME events, but rather call it from
the API functions that the driver (or rather mac80211)
calls. This separates the code better.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do some cleanups in the cfg80211 SME APIs, which are
only used by mac80211.
Most of these functions get a frame passed, and there
isn't really any reason to export multiple functions
as cfg80211 can check the frame type instead, do that.
Additionally, the API functions have confusing names
like cfg80211_send_...() which was meant to indicate
that it sends an event to userspace, but gets a bit
confusing when there's both TX and RX and they're not
all clearly labeled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge to get the wil6210 changes that a cfg80211 change needs.
A conflict in drivers/net/wireless/ath/ath9k/init.c was just
whitespace changes.
Also fix a semantic conflict due to cw1200 using WoWLAN which
I had modified in my tree.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The connection monitor needs to know the tx status of
nullframes to work properly.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
genlmsg_end() can't return an error since it returns the
skb length so remove checks treating the return value as
an error code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move message to debug mode to reduce log spam under heavy tx (iperf) load.
This message prints in ht debug mode only:
brcms_c_ampdu_dotxstatus_complete: Pkt tx suppressed, illegal channel
possibly 153
Signed-off-by: John Greene <jogreene@redhat.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI state can be maintained globally instead of per-channel.
This reduces memory usage and since default values are used
during a scan run, per-channel state is not required.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The macros ATH9K_ANI_USE_OFDM_WEAK_SIG can be removed.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>