For some reason, the select input of pin function USB_OTG_ID is not
implemented via a regular select input register but using the bit
USB_OTG_ID_ SEL (shift 13) of IOMUXC_GPR1 register (offset 0x4).
As per the workaround for such quirk implemented in pinctrl driver,
we need to compose the input_val cell as below.
31 23 15 7 0
| 0xff | shift | width | select |
Thus, we have 0xff0d0100 for MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID and
0xff0d0101 for MX6QDL_PAD_GPIO_1__USB_OTG_ID in input_val cell.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The patch "0b7a76a ARM: dts: imx6q{dl}: add DTE pads for uart"
adds the DTE pads for uart. For PAD_EIM_D29, the offset of the
Pad Mux register should be 0x0c8, not 0x0c4.
This patch fixes it.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx6q and imx6dl are two pin-to-pin compatible SoCs. The same board
design can work with either chip plugged into the socket, e.g. sabresd
and sabreauto boards.
We currently define pin groups in imx6q.dtsi and imx6dl.dtsi
respectively because the pad macro names are different between two
chips. This brings a maintenance burden on having the same label point
to the same pin group defined in two places.
The patch replaces prefix MX6Q_ and MX6DL_ with MX6QDL_ for both SoCs
pad macro names. Then the pin groups becomes completely common between
imx6q and imx6dl and can just be moved into imx6qdl.dtsi, so that the
long term maintenance of imx6q/dt pin settings becomes easier.
Unfortunately, the change brings some dramatic diff stat, but it's all
about DTS file, and the ultimate net diff stat is good.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The uart2 in the imx6q-arm2 board is used as a DTE uart,
this patch adds the necessary DTE pads for uart2.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Currently, all imx pinctrl drivers maintain a big array of struct
imx_pin_reg which hard-codes data like register offset and mux mode
setting for each pin function. Every time a new imx SoC support is
added, we need to add such a big mount of data. With moving to single
kernel build, it's only matter of time to be blamed on memory consuming.
With DTC pre-processor support in place, the patch moves all these data
into device tree by redefining the PIN_FUNC_ID in imxXX-pinfunc.h and
changing the PIN_FUNC_ID parsing code a little bit.
The pin id gets re-numbered based on mux register offset, or config
register offset if the pin has no mux register, so that kernel can
identify the pin id from register offsets provided by device tree.
As a bonus point of the change, those arbitrary magic numbers standing
for particular PIN_FUNC_ID in device tree sources are now replaced by
macros to improve the readability of dts files.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
