This adds a DT node for the system-controller found on Marvell Dove
SoCs.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Describe the T5325 using device tree properties, where possible. The
first version of this file was produced by Thomas Petazzoni.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When using platform_driver instantiation, the i2c bus was given bus
number 0. The kirkwood-t5325 audio driver has this bus number hard
coded for the address of the codec. However by default device tree i2c
busses are dynamically allocated a bus number, starting from 1. Thus
the kirkwood-t5325 cannot find its audio codec. By adding an alias in
the DT file we can control the bus number and set it to 0. The codec
can then be found.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The binding has existed for a while, so add the missing node so it can
be used by devices.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With kirkwood migrating into mach-mvebu, mvebu_v5_defconfig needs to
select ARCH_MVEBU. Unfortunately, this means that when building a v5
kernel, we unnecessarily build dtbs for the armada v7 boards.
To fix this, we instead select based on MACH_ARMADA_* on a per SoC basis.
Reported-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
We share global config registers by syscon node, add it to dove.dtsi.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Dove pinctrl uses additional registers to control MPPs. This patch first
increases existing pinctrl reg property by one register, and then adds
two new ranges for MPP4 and PMU MPP registers.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Make use of the mvebu system controller, by placing a node into the
dtsi file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the Feroceon L2 cache has a DT binding, make use of it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Instead of hardcoding the values of the interrupt flags, use the
macros provided by <include/dt-bindings/interrupt-controller/irq.h>
and <include/dt-bindings/interrupt-controller/arm-gic.h> for the
Armada 375 and Armada 38x Device Tree files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Instead of hardcoding 0 and 1 to indicate SPI and PPI GIC interrupts,
use the definitions of <dt-bindings/interrupt-controller/arm-gic.h> to
clarify the Device Tree code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Some of the Armada 375/38x DTs that were recently submitted were still
using the old-style /include/ instead of the new-style, C-preprocessor
based #include. Since we are going to start including more headers,
switching to the C-preprocessor based includes is important.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add device tree fragments and files to support many of the kirkwood
based Synology NAS devices. This is a modification of
Andrew Lunn's <andrew@lunn.ch> translation of the board setup file
maintained by Ben Peddell <klightspeed@killerwolves.net>
The Ricoh RS5C372 RTC was used in all 2009 units and some 2010 units.
All other Synology Kirkwood-based DiskStations and RackStations use
the Seiko S35390A RTC.
Most of the 1-bay and 2-bay units use the GPIOs that are multiplexed
with the built-in SATA interface activity/presence pins on mpp 20-23,
while the 4-bay units use ge01 and a PCIe SATA controller, and put the
software controlled HDD leds on mpp 36-43.
Most of the 6281 units with HDD power controls use mpp 29 and 31, while
most of the 6282 units with HDD power controls use mpp 30, 34, 44 and 45
and provide a model ID on mpp 28, 29, 46 and 47. Pre-2012 units and
most 4-bay units didn't have a separate power control for HDD1. These
power controls are presumably to limit startup current from the 12V
brick power supply.
Instead of using separate dtsi files in a synology directory, this
patch uses a single dtsi file containing all of the modules for
these boards, with all of the modules not common to all boards
disabled. The board dts files then enable the appropriate modules for
their boards.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Tested-by: Ben Peddell <klightspeed@killerwolves.net> (ds211j)
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add the Seiko Instruments Inc S35390a to the list of trivial i2c
devices.
Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The following patches make use of vendor names:
* ricoh (Ricoh Co. Ltd.);
* qnap (QNAP Systems, Inc.);
* sii (Seiko Instruments, Inc.); and
* synology (Synology, Inc.)
Add them to the vendor prefix list.
Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The corresponding driver didn't make it into v3.14, so we need to remove
the node. Dove systems fail to boot with the node present and no
driver.
This node will be re-added when the driver makes it to mainline.
Reported-by: Jean-Francois Moine <moinejf@free.fr>
Tested-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 385 DB board is the development board from Marvell for the
Armada 385 SoC. This commit adds a Device Tree description for this
board, which enables the following features:
* Network interfaces
* I2C buses
* SDIO
* Serial port
* SPI bus, with a SPI flash
* PCIe interfaces
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 380 and 385 SoCs are new SoCs from Marvell, based on a
Cortex-A9 cores (single core for 380, dual core for 385) and a number
of hardware blocks that are common with earlier SoCs from the mvebu
family.
The provided Device Tree describes the following parts of the SoC:
* CPU
* Device Bus
* Clocks
* Interrupt controllers: GIC and MPIC
* GPIO controllers
* I2C buses
* L2 cache
* MBus controller
* Pinctrl
* Serial
* SPI buses
* System controller (for reboot)
* Timer
* XOR engines
* PCIe controllers
* Network interfaces
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 375 DB board is the development board from Marvell for the
Armada 375 SoC. This commit adds a Device Tree description for this
board, which enables the following features:
* I2C buses
* SDIO
* Serial port
* SPI bus, with a SPI flash. Note that the SPI bus is disabled by
default, because it conflicts with the NAND, and can only work if
the board boots out of SPI. Since most boards are shipped to boot
out of NAND, we're default to having the SPI bus disabled.
* PCIe interfaces
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 375 SoC is a new SoC from Marvell, based on a dual core
Cortex-A9 and a number of hardware blocks that are common with earlier
SoCs from the mvebu family.
The provided Device Tree describes the following parts of the SoC:
* CPUs
* Device Bus
* Clocks
* Interrupt controllers: GIC and MPIC
* GPIO controllers
* I2C buses
* L2 cache
* MBus controller
* SDIO
* Pinctrl
* SATA
* Serial
* SPI buses
* System controller (for reboot)
* Timer
* XOR engines
* PCIe controllers
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add the devicetree node to enable watchdog support available in Dove SoCs.
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In order to support multiplatform builds the watchdog devicetree binding
was modified and now the 'reg' property is specified to need two
entries. This commit adds the second entry as-per the new specification.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add the DT nodes to enable watchdog support available in Armada 370
and Armada XP SoCs.
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Perform a mechanical translation of rd88f6281-setup.c into DT. Since
the hardware differs between the A0 and A1 stepping, two dts files are
used, and a .dtsi file for the common parts. The A0 part does not have
a "wan" port on the switch and uses PHY address 10 to address the
switch. The A1 part does have the "wan" port and uses address 0.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Mechanically translate rd88f6192-nas-setup.c into DT equivelent.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In addition to the analog audio input and output, the Armada 370 DB
also has S/PDIF input and output optical connectors. This commit
improves the Device Tree description of the Armada 370 DB platform to
enable the S/PDIF support.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds the necessary Device Tree informations to enable
audio support on the Armada 370 DB platform. In details it:
* Instantiates the CS42L51 audio codec on the I2C0 bus, and
configures this bus with the appropriate pin-muxing configuration.
* Enables the I2S audio controller, and configures it with the
appropriate pin-muxing configuration.
* Through hog pins, ensures that the other pins possibly used for I2S
are muxed with another function than I2S.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds a pin-muxing configuration for the I2C0 bus of the
Armada 370, which is used on the Armada 370 DB platform to interface
with the CS42L51 audio codec.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 370 SoC has an I2S audio controller. This commit adds the
description of this controller to the Device Tree describing this SoC,
as well as two possible muxing configurations for the I2S bus pins.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Instead of harcoding keycodes specifications in the Armada 370/XP
boards, use the <dt-bindings/input/input.h> header file and its
keycode definitions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Instead of harcoding 0 and 1 for the gpio specifications in the Armada
370/XP boards, use the <dt-bindings/gpio/gpio.h> header file and its
GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW definitions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
It was correctly set on mv78460 but not on mv78260, resulting in my
OpenBlocks AX3-4 retrieving only 3 of its 4 MAC addresses from the
boot loader.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Re-implement the Marvell Kirkwood ts41x-setup.c in DT.
As with the QNAP 119, there are two variants, depending on which SoC
has been used. They differ on Ethernet PHY addresses and number of
PCIe busses.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Ian Campbell <ijc@hellion.org.uk> (kirkwood-ts419-6281.dtb)
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Excito Bubba B3 is a home server, single drive NAS box, Wifi
access point, etc.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull parisc updates from Helge Deller:
"The three major changes in this patchset is a implementation for
flexible userspace memory maps, cache-flushing fixes (again), and a
long-discussed ABI change to make EWOULDBLOCK the same value as
EAGAIN.
parisc has been the only platform where we had EWOULDBLOCK != EAGAIN
to keep HP-UX compatibility. Since we will probably never implement
full HP-UX support, we prefer to drop this compatibility to make it
easier for us with Linux userspace programs which mostly never checked
for both values. We don't expect major fall-outs because of this
change, and if we face some, we will simply rebuild the necessary
applications in the debian archives"
* 'parisc-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: add flexible mmap memory layout support
parisc: Make EWOULDBLOCK be equal to EAGAIN on parisc
parisc: convert uapi/asm/stat.h to use native types only
parisc: wire up sched_setattr and sched_getattr
parisc: fix cache-flushing
parisc/sti_console: prefer Linux fonts over built-in ROM fonts
HPFS needs to load 4 consecutive 512-byte sectors when accessing the
directory nodes or bitmaps. We can't switch to 2048-byte block size
because files are allocated in the units of 512-byte sectors.
Previously, the driver would allocate a 2048-byte area using kmalloc,
copy the data from four buffers to this area and eventually copy them
back if they were modified.
In the current implementation of the buffer cache, buffers are allocated
in the pagecache. That means that 4 consecutive 512-byte buffers are
stored in consecutive areas in the kernel address space. So, we don't
need to allocate extra memory and copy the content of the buffers there.
This patch optimizes the code to avoid copying the buffers. It checks
if the four buffers are stored in contiguous memory - if they are not,
it falls back to allocating a 2048-byte area and copying data there.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously, hpfs scanned all bitmaps each time the user asked for free
space using statfs. This patch changes it so that hpfs scans the
bitmaps only once, remembes the free space and on next invocation of
statfs it returns the value instantly.
New versions of wine are hammering on the statfs syscall very heavily,
making some games unplayable when they're stored on hpfs, with load
times in minutes.
This should be backported to the stable kernels because it fixes
user-visible problem (excessive level load times in wine).
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the flexible mmap memory layout (as described in
http://lwn.net/Articles/91829). This is especially very interesting on
parisc since we currently only support 32bit userspace (even with a
64bit Linux kernel).
Signed-off-by: Helge Deller <deller@gmx.de>
On Linux, only parisc uses a different value for EWOULDBLOCK which
causes a lot of troubles for applications not checking for both values.
Since the hpux compat is long dead, make EWOULDBLOCK behave the same as
all other architectures.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Signed-off-by: Helge Deller <deller@gmx.de>
The stat.h header file is exported to userspace. Some userspace
applications failed to compile due to missing/unknown types, so we
better convert it to use native types only (like it's done on other
architectures too).
Signed-off-by: Helge Deller <deller@gmx.de>
This commit:
f8dae00684: parisc: Ensure full cache coherency for kmap/kunmap
caused negative caching side-effects, e.g. hanging processes with expect and
too many inequivalent alias messages from flush_dcache_page() on Debian 5 systems.
This patch now partly reverts it and has been in production use on our debian buildd
makeservers since a week without any major problems.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Helge Deller <deller@gmx.de>
The built-in ROM fonts lack many necessary ASCII characters, which is
why it makes sens to prefer the Linux fonts instead if they are
available. This makes consoles on STI graphics cards which are not
supported by the stifb driver (e.g. Visualize FXe) looks much nicer.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v3.13
Pull SLAB changes from Pekka Enberg:
"Random bug fixes that have accumulated in my inbox over the past few
months"
* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
mm: Fix warning on make htmldocs caused by slab.c
mm: slub: work around unneeded lockdep warning
mm: sl[uo]b: fix misleading comments
slub: Fix possible format string bug.
slub: use lockdep_assert_held
slub: Fix calculation of cpu slabs
slab.h: remove duplicate kmalloc declaration and fix kernel-doc warnings
Pull turbostat updates from Len Brown.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: introduce -s to dump counters
tools/power turbostat: remove unused command line option
turbostat: Add option to report joules consumed per sample
turbostat: run on HSX
turbostat: Add a .gitignore to ignore the compiled turbostat binary
turbostat: Clean up error handling; disambiguate error messages; use err and errx
turbostat: Factor out common function to open file and exit on failure
turbostat: Add a helper to parse a single int out of a file
turbostat: Check return value of fscanf
turbostat: Use GCC's CPUID functions to support PIC
turbostat: Don't attempt to printf an off_t with %zx
turbostat: Don't put unprocessed uapi headers in the include path
Here's a set of patches for (hopefully) -rc1. Some of them are fixes,
but a good number of them also do things such as enable new drivers in
the defconfigs for platforms that have such devices, increases coverage
of the multiplatform defconfig and some DTS changes that plumbs up some
of the devices that now have bindings and driver support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJS7VYsAAoJEIwa5zzehBx3FKIQAIVIkjlKAtvRpg+P/BYWigXq
6jG2xuBhwf1Yciu70ttvfRnR9bGJc+0o5w/qjr7ARSFp7GkDlWXtIwj+1EwGSEES
hB/f2GcBfNLJOI0rHvvudz+7HlpiyfB6iMj3U25hnpShrSTxbOHDC6pU6pYjUzBy
T1AYTmfa0vwuy9TNodOr4dVYlbJc3YA0V2sBTusXDFwm03XTdCd7E7RJIr/MRDEN
96PtaNrfstmxeTjN0NBuL2IdsZNR2mn/cgWTL1lVqVE8+z7QyvmPDqmWD5iCVQaM
+6mJbXL4jzM1CyB8Qf89sNtTaFVjwbgvbtuljPv/7q/jhf2rvixaMzywCv28FjB+
uJCaLh1r/HiR61tlw0yX3ixPdKFJqyWV9vF5+uuwmEQCCPpFWGzTcNaZ7NRiYzEt
yqt1ZRDhEAli8iHt96LxMwLIklaDGvuxLtHsv4a5djEoaO/yqRTNZXDjwIsIzkpD
N8vUwPf7Pnw+3/5iGVTQdZaPzmrNjqTOLwz0s7ys2avVsRsNNi68hMuIj+qrNlzu
/tJhhh0u9SONRM3c6D9mtrZPD7Gs8QgMbT9TyZ2/ILQKuo4wO9F1GDN93MjZI5oq
1rX/QUeYItWQamzHGmI8ZlAx4YlsxxB90eJ8CaG2F8sVtumklrFRb43Vf9NRsyo/
XDrjoS/cdi7PAO0wemkg
=ymAC
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a set of patches for (hopefully) -rc1. Some of them are fixes,
but a good number of them also do things such as enable new drivers in
the defconfigs for platforms that have such devices, increases
coverage of the multiplatform defconfig and some DTS changes that
plumbs up some of the devices that now have bindings and driver
support.
The commit dates are recent; we've mostly collected these fixes in the
last few days but I also had to rebuild the branch yesterday to sort
out some internal conflicts which reset the timestamps. The changes
should have been tested by each platform maintainer already (and few
of them have cross-platform impact) so I'm personally not too
concerned by it at this time"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMA
ARM: multi_v7_defconfig: add mvebu drivers
clocksource: kona: Add basic use of external clock
drivers: bus: fix CCI driver kcalloc call parameters swap
ARM: dts: bcm28155-ap: Fix Card Detection GPIO
ARM: multi_v7_defconfig: Select CONFIG_AT803X_PHY
ARM: keystone: config: fix build warning when CONFIG_DMADEVICES is not set
MAINTAINERS: ARM: SiRF: use regex patterns to involve all SiRF drivers
ARM: dts: zynq: Add SDHCI nodes
ARM: hisi: don't select SMP
ARM: tegra: rebuild tegra_defconfig to add DEBUG_FS
ARM: multi_v7: copy most options from tegra_defconfig
ARM: iop32x: fix power off handling for the EM7210 board
ARM: integrator: restore static map on the CP
ARM: msm_defconfig: Enable MSM clock drivers
ARM: dts: msm: Add clock controller nodes and hook into uart
ARM: OMAP4+: move errata initialization to omap4_pm_init_early
ARM: OMAP4460: cpuidle: Extend PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD on cpuidle
ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference
...
