The current code has 2 problems:
1. The maximum wait time is not long enough. It is about 60% of the
duration specified by the firmware. It is calling usleep_range(600, 800)
for every 1 msec we are supposed to wait.
2. The granularity of the delay is too coarse. Many simple firmware
commands finish in 25 usec or less.
We fix these 2 issues by multiplying the original 1 msec loop counter by
40 and calling usleep_range(25, 40) for each iteration.
There is also a second delay loop to wait for the last DMA word to
complete. This delay loop should be a very short 5 usec wait.
This change results in much faster bring-up/down time:
Before the patch:
time ip link set p4p1 up
real 0m0.120s
user 0m0.001s
sys 0m0.009s
After the patch:
time ip link set p4p1 up
real 0m0.030s
user 0m0.000s
sys 0m0.010s
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip supports 4K/8K/64K page sizes for the rings and we try to
match it to the CPU PAGE_SIZE. The current page size limits for the rings
are based on 4K/8K page size. If the page size is 64K, these limits are
too large. Reduce them appropriately.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to log a message during driver load indicating PCIe link
speed and width.
The log message will look like this:
bnxt_en 0000:86:00.0 eth0: PCIe: Speed 8.0GT/s Width x8
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to fetch the SFP EEPROM settings from the firmware
and display it via the ethtool -m command. We support SFP+ and QSFP
modules.
v2: Fixed a bug in bnxt_get_module_eeprom() found by Ben Hutchings.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is only 1 MSI-X vector or in INTA mode, tx and rx pre-set
max channel parameters are shown incorrectly in ethtool -l. With only 1
vector, bnxt_get_max_rings() will return -ENOMEM. bnxt_get_channels
should check this return value, and set max_rx/max_tx to 0 if it is
non-zero.
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Switchdev has been around for quite a while now, putting "EXPERIMENTAL"
in the description is no longer accurate, drop it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Original implementation commit e54bcde3d6 ("arm64: eBPF JIT compiler")
had the relevant code paths, but due to an oversight always fail jiting.
As a result, we had been falling back to BPF interpreter whenever a BPF
program has JMP_JSET_{X,K} instructions.
With this fix, we confirm that the corresponding tests in lib/test_bpf
continue to pass, and also jited.
...
[ 2.784553] test_bpf: #30 JSET jited:1 188 192 197 PASS
[ 2.791373] test_bpf: #31 tcpdump port 22 jited:1 325 677 625 PASS
[ 2.808800] test_bpf: #32 tcpdump complex jited:1 323 731 991 PASS
...
[ 3.190759] test_bpf: #237 JMP_JSET_K: if (0x3 & 0x2) return 1 jited:1 110 PASS
[ 3.192524] test_bpf: #238 JMP_JSET_K: if (0x3 & 0xffffffff) return 1 jited:1 98 PASS
[ 3.211014] test_bpf: #249 JMP_JSET_X: if (0x3 & 0x2) return 1 jited:1 120 PASS
[ 3.212973] test_bpf: #250 JMP_JSET_X: if (0x3 & 0xffffffff) return 1 jited:1 89 PASS
...
Fixes: e54bcde3d6 ("arm64: eBPF JIT compiler")
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Yang Shi <yang.shi@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when creating or updating a route, no check is performed
in both ipv4 and ipv6 code to the hoplimit value.
The caller can i.e. set hoplimit to 256, and when such route will
be used, packets will be sent with hoplimit/ttl equal to 0.
This commit adds checks for the RTAX_HOPLIMIT value, in both ipv4
ipv6 route code, substituting any value greater than 255 with 255.
This is consistent with what is currently done for ADVMSS and MTU
in the ipv4 code.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The slab name ends up being visible in the directory structure under
/sys, and even if you don't have access rights to the file you can see
the filenames.
Just use a 64-bit counter instead of the pointer to the 'net' structure
to generate a unique name.
This code will go away in 4.7 when the conntrack code moves to a single
kmemcache, but this is the backportable simple solution to avoiding
leaking kernel pointers to user space.
Fixes: 5b3501faa8 ("netfilter: nf_conntrack: per netns nf_conntrack_cachep")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs fixes from Al Viro:
"Overlayfs fixes from Miklos, assorted fixes from me.
Stable fodder of varying severity, all sat in -next for a while"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ovl: ignore permissions on underlying lookup
vfs: add lookup_hash() helper
vfs: rename: check backing inode being equal
vfs: add vfs_select_inode() helper
get_rock_ridge_filename(): handle malformed NM entries
ecryptfs: fix handling of directory opening
atomic_open(): fix the handling of create_error
fix the copy vs. map logics in blk_rq_map_user_iov()
do_splice_to(): cap the size before passing to ->splice_read()
This patch fixes SG_RX_DV_GATE_REG_0_ADDR register offset
and ring state field lengths.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the race condition on updating the statistics
counters by moving the counters to the ring structure.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses ununiform latency across queues by adding
more queues to match with, upto number of CPU cores.
Also, number of interrupts are increased and the channel numbers
are reordered.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hardware doesn't allow sharing of interrupts,
this patch fixes the same by removing IRQF_SHARED flag.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the crash observed during IPv4 forward test by
setting the drop field in the dbptr.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2016-05-13
This series contains updates to e1000e, igb and igbvf.
Steve Shih fixes an issue for disabling auto-negotiation and forcing
speed and duplex settings for non-copper media.
Brian Walsh cleanups some inconsistency in the use of return variables
names to avoid confusion.
Jake cleans up the drivers to use the BIT() macro when it can, which will
future proof the drivers for GCC 6 when it gets released. Cleaned up
dead code which was never being used. Also fixed e1000e, where it was
incorrectly restting the SYSTIM registers every time the ioctl was being
run.
Denys Vlasenko fixes an oversight where incvalue variable holds a 32
bit value so we should declare it as such, instead of 64 bits. Also
fixed an overflow check, where two reads are the same, then it is not
an overflow.
Nathan Sullivan fixes the PTP timestamps for transmit and receive
latency based on the current link speed.
Alexander Duyck adds support for partial GSO segmentation in the case
of tunnels for igb and igbvf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull cgroup fixes from Tejun Heo:
"During v4.6-rc1 cgroup namespace support was merged. There is an
issue where it's impossible to tell whether a given cgroup mount point
is bind mounted or namespaced. Serge has been working on the issue
but it took longer than expected to resolve, so the late pull request.
Given that it's a completely new feature and the patches don't touch
anything else, the risk seems acceptable. However, if this is too
late, an alternative is plugging new cgroup ns creation for v4.6 and
retrying for v4.7"
* 'for-4.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: fix compile warning
kernfs: kernfs_sop_show_path: don't return 0 after seq_dentry call
cgroup, kernfs: make mountinfo show properly scoped path for cgroup namespaces
kernfs_path_from_node_locked: don't overwrite nlen
Pull workqueue fix from Tejun Heo:
"CPU hotplug callbacks can invoke DOWN_FAILED w/o preceding
DOWN_PREPARE which can trigger a WARN_ON() in workqueue.
The bug has been there for a very long time. It only triggers if CPU
down fails at a specific point and I don't think it has adverse
effects other than the warning messages. The fix is very low impact"
* 'for-4.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix rebind bound workers warning
The e1000e_config_hwtstamp function was incorrectly resetting the SYSTIM
registers every time the ioctl was being run. If you happened to be
running ptp4l and lost the PTP connect (removing cable, or blocking the
UDP traffic for example), then ptp4l will eventually perform a restart
which involves re-requesting timestamp settings. In e1000e this has the
unfortunate and incorrect result of resetting SYSTIME to the kernel
time. Since kernel time is usually in UTC, and PTP time is in TAI, this
results in the leap second being re-applied.
Fix this by extracting the SYSTIME reset out into its own function,
e1000e_ptp_reset, which we call during reset to restore the hardware
registers. This function will (a) restart the timecounter based on the
new system time, (b) restore the previous PPB setting, and (c) restore
the previous hwtstamp settings.
In order to perform (b), I had to modify the adjfreq ptp function
pointer to store the old delta each time it is called. This also has the
side effect of restoring the correct base timinca register correctly.
The driver does not need to explicitly zero the ptp_delta variable since
the entire adapter structure comes zero-initialized.
Reported-by: Brian Walsh <brian@walsh.ws>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brian Walsh <brian@walsh.ws>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for partial GSO segmentation in the case of
tunnels. Specifically with this change the driver an perform segmentation
as long as the frame either has IPv6 inner headers, or we are allowed to
mangle the IP IDs on the inner header. This is needed because we will not
be modifying any fields from the start of the start of the outer transport
header to the start of the inner transport header as we are treating them
like they are just a block of IP options.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The E1000_ICH_NVM_SIG_MASK value is shifted, out to the 31st bit, which
is the signed bit for signed constants. Mark these values as unsigned to
prevent compiler warnings and issues on platforms which a different
signed bit implementation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This prevents signed bitshift issues when the shift would overwrite the
signed bit, and prevents making this mistake in the future when copying
and modifying code.
Use GENMASK or the unsigned postfix for cases which aren't suitable for
BIT() macro.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To prevent signed bitshift issues, and improve code readability, use the
BIT() macro. Also make use of GENMASK or the unsigned postfix where this
is more appropriate than BIT()
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The variable rdlen is set but never used, and thus setting it is dead
code. Remove it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Table 7-62 on page 338 of the i210 datasheet lists TX and RX latencies
for the various speeds the chip supports. To give better PTP timestamp
accuracy, adjust the timestamps by the amounts Intel gives based on
current link speed.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
SYSTIMH:SYSTIML registers are incremented by 24-bit value TIMINCA[23..0]
er32(SYSTIML) are probably moderately expensive (they are pci bus reads).
Can we avoid one of them? Yes, we can.
If the SYSTIML value we see is smaller than 0xff000000, the overflow
into SYSTIMH would require at least two increments.
We do two reads, er32(SYSTIML) and er32(SYSTIMH), in this order.
Even if one increment happens between them, the overflow into SYSTIMH
is impossible, and we can avoid doing another er32(SYSTIML) read
and overflow check.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If two consecutive reads of the counter are the same, it is also
not an overflow. "systimel_1 < systimel_2" should be
"systimel_1 <= systimel_2".
Before the patch, we could perform an *erroneous* correction:
Let's say that systimel_1 == systimel_2 == 0xffffffff.
"systimel_1 < systimel_2" is false, we think it's an overflow,
we read "systimeh = er32(SYSTIMH)" which meanwhile had incremented,
and use "(systimeh << 32) + systimel_2" value which is 2^32 too large.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: intel-wired-lan@lists.osuosl.org
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
"incvalue" variable holds a result of "er32(TIMINCA) &
E1000_TIMINCA_INCVALUE_MASK" and used in "do_div(temp, incvalue)"
as a divisor.
Thus, "u64 incvalue" declaration is probably a mistake.
Even though it seems to be a harmless one, let's fix it.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For bitshifts, we should make use of the BIT macro when possible, and
ensure that other bitshifts are marked as unsigned. This helps prevent
signed bitshift errors, and ensures similar style.
Make use of GENMASK and the unsigned postfix where BIT() isn't
appropriate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixed the file to use a consistent ret_val for return value checking.
Signed-off-by: Brian Walsh <brian@walsh.ws>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the issues for disabling auto-negotiation and forcing
speed and duplex settings for the non-copper media.
For non-copper media, e1000_get_settings should return ETH_TP_MDI_INVALID for
eth_tp_mdix_ctrl instead of ETH_TP_MDI_AUTO so subsequent e1000_set_settings
call would not fail with -EOPNOTSUPP.
e1000_set_spd_dplx should not automatically turn autoneg back on for forced
1000 Mbps full duplex settings for non-copper media.
Cc: xe-kernel@external.cisco.com
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Steve Shih <sshih@cisco.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull scheduler fix from Ingo Molnar:
"This is a revert to fix an interactivity problem.
The proper fixes for the problems that the reverted commit exposed are
now in sched/core (consisting of 3 patches), but were too risky for
v4.6 and will arrive in the v4.7 merge window"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "sched/fair: Fix fairness issue on migration"
Pull perf fixes from Ingo Molnar:
"An uncharacteristically large number of bugs popped up in the last
week:
- various tooling fixes, two crashes and build problems
- two Intel PT fixes
- an KNL uncore driver fix
- an Intel PMU driver fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf stat: Fallback to user only counters when perf_event_paranoid > 1
perf evsel: Handle EACCESS + perf_event_paranoid=2 in fallback()
perf evsel: Improve EPERM error handling in open_strerror()
tools lib traceevent: Do not reassign parg after collapse_tree()
perf probe: Check if dwarf_getlocations() is available
perf dwarf: Guard !x86_64 definitions under #ifdef else clause
perf tools: Use readdir() instead of deprecated readdir_r()
perf thread_map: Use readdir() instead of deprecated readdir_r()
perf script: Use readdir() instead of deprecated readdir_r()
perf tools: Use readdir() instead of deprecated readdir_r()
perf/core: Disable the event on a truncated AUX record
perf/x86/intel/pt: Generate PMI in the STOP region as well
perf/x86: Fix undefined shift on 32-bit kernels
perf/x86/msr: Fix SMI overflow
perf/x86/intel/uncore: Fix CHA registers configuration procedure for Knights Landing platform
perf diff: Fix duplicated output column
- The Atmel sama5d2 was registering the wrong NFC device type
- On Atmel sam9x5, the power management controller had an incorrect
register area size
- On ARM64 Allwinner machine was not secting the generic irqchip
code, causing build errors in some configurations
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HPqy
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Three more bug fixes for ARM SoCs this week:
- The Atmel sama5d2 was registering the wrong NFC device type
- On Atmel sam9x5, the power management controller had an incorrect
register area size
- On ARM64 Allwinner machine was not secting the generic irqchip
code, causing build errors in some configurations"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: at91: sam9x5: Fix the memory range assigned to the PMC
arm64/sunxi: 4.6-rc1: Add dependency on generic irq chip
ARM: dts: at91: sama5d2: use "atmel,sama5d3-nfc" compatible for nfc
A small collection of driver specific fixes for the regulator
subsysetem:
- Fix handling of probe deferral for GPIO regulators.
- Fix a typo in the module alias for DA9053.
- Fix the definition of BUCK9 in the S2MPS11 driver. This change looks
larger than it is because an irregularity in the hardware means that
the macro used to define bucks 6-10 needs duplicating and tweaking
to have a separate macro for 9.
- Fix a series of errors in the definitions of the LDOs the AXP20x
regulators, some of which had always been present and some of which
were introduced in the merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXNazxAAoJECTWi3JdVIfQd9EH/0x/3Era4ctuLFP/dKVg+lAQ
PDwgGRlHg1RVyEzzy1ZWqew//P7hgBo6urwFHjcczBE95e0bBhhMJERGnhya07uq
eWYfPARl1zHxEm0gOfLBDaFAW8YIaNyXiEsW/aTeViNIL9/HIAd/ZTZhJiDLPiAF
FdNs3yzBuAR5SHsnvCTXZY1d20LeQC6AC2nWUo2WrcyKKZZ0HamrSLP0lMq0OHVQ
n2h/8f1g9TcykakCStB/4D8vLKMt0OYmalh3Y/C/JGkWnhMoBTLRgktrNFh6lnh9
E0SnMXSuZbC9+mv8MLRHQft6XagDYzNq+odwSb9tfqbXqBdncOpvvVr6hLmzxGk=
=sVmG
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A small collection of driver specific fixes for the regulator
subsysetem:
- Fix handling of probe deferral for GPIO regulators
- Fix a typo in the module alias for DA9053
- Fix the definition of BUCK9 in the S2MPS11 driver. This change
looks larger than it is because an irregularity in the hardware
means that the macro used to define bucks 6-10 needs duplicating
and tweaking to have a separate macro for 9
- Fix a series of errors in the definitions of the LDOs the AXP20x
regulators, some of which had always been present and some of which
were introduced in the merge window"
* tag 'regulator-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: da9063: Correct module alias prefix to fix module autoloading
regulator: axp20x: Fix axp22x ldo_io registration error on cold boot
regulator: axp20x: Fix axp22x ldo_io voltage ranges
regulator: axp20x: Fix LDO4 linear voltage range
regulator: s2mps11: Fix invalid selector mask and voltages for buck9
regulator: gpio: check return value of of_get_named_gpio
This is rather too late so it'd be completely understandable if you
don't want to pull it at this point, I had thought I'd sent this earlier
but it seems I didn't. Everything has been in -next for some time now.
The main set of fixes here are mopping up some more issues with MMIO,
fixing handling of endianness configuration in DT (which just wasn't
working at all) and cases where the register and value endianness are
different.
There is also a fix for bulk register reads on SPMI.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXNaKUAAoJECTWi3JdVIfQoxEH/1DZGfeFyqhh4cdxrYz6UUr/
MbfMDR1wxNEvD4pifak6wYzQlern2Ki4J8ac72LP2OH9MYEoVs7kxESdSbqcVerc
uWQmn1qzj41hBSP5I4zmHIvYAwDry3B8mVVK9aYk+kBZLyOiw0eoMgZYyxB9cqws
pnfR4+5XHcaLGxh8QdIM7cXW1YOykXma4ivdwjwSlgWhYLGdh++j/uo9IUxqCrSa
qqxfMLPvAtEcksH8p4sJoRjibVDvzLXOvr3jMVHWyFoRGNDDB4TRiPkvydI04vYP
39pjg3c4gIAmp/RFyie1B8+zm4C+EQAkeiyH6D4jq8k9Gu6Y/XhqwFIAKtni3zg=
=k8tp
-----END PGP SIGNATURE-----
Merge tag 'regmap-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"This is rather too late so it'd be completely understandable if you
don't want to pull it at this point, I had thought I'd sent this
earlier but it seems I didn't. Everything has been in -next for some
time now.
The main set of fixes here are mopping up some more issues with MMIO,
fixing handling of endianness configuration in DT (which just wasn't
working at all) and cases where the register and value endianness are
different.
There is also a fix for bulk register reads on SPMI"
* tag 'regmap-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: spmi: Fix regmap_spmi_ext_read in multi-byte case
regmap: mmio: Explicitly say little endian is the defualt in the bus config
regmap: mmio: Parse endianness definitions from DT
regmap: Fix implicit inclusion of device.h
regmap: mmio: Fix value endianness selection
regmap: fix documentation to match code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXNbnRAAoJEAhfPr2O5OEV9NAP/R72SwjZZrPV8ABV/yF6iiRL
pEcnDWP1vfOq3hlWKAvKHtzyAh13zUlkf0WAZJ5SFbkIyxrPD1mNCjwqNdYPFUpS
m2kAP7E8sU3ldRCdlD9QpsaOnrnRVpsPc8ChawqRyp0gVs/b+I3cJ82l2S1JHwTR
wO+7Uid3FwDtgzuiTecmtDiqKJJ1AgW3YNXJXnug2L6bAhPxHgJct+OV2K/n37de
MSIaVNHkIZxaFLXtIoCWiyxhJQCngAQhdDm+wxNGWupSdxmqArBq9QljX/6ZR9rB
7OFT8Td85J59WmMhxSvbjfCnlj0KO/fJX/QIaBXK4gFtolZxgpVAsxHaWMWtrrii
UitDMcRL1aEyygpwW72BqJ62r4RQn1QBBTRUaGlAWzYwZU6C0B0Aj70qhxdocjNE
cxv6ND2WftbYIUEQceLrFV7Qzee07YIS+FapB1Vda1s+mDtfCBnfd+n5gTkGmIeY
bweoHGAELDPyLntu6iboqAtG5MiSWGUtOEAZsYhm7ugY5OeCh8wiq4lUDsb2hQ3T
TnaCVPHEFghN5+KAmiFcp46lOCab8H0crmfEmSMGzcIMf1fZBYUc8TjceGb5GHI/
l2uNYAUz7vrZvs/qX/tKfIEERlzDgDTvw1T8NL6yt8fKzZA4Ajr3WhWntBbrfnXi
KplRJ1ngkpoArG4+24v9
=PEbo
-----END PGP SIGNATURE-----
Merge tag 'media/v4.6-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fix from Mauro Carvalho Chehab:
"A revert fixing a breakage that caused an OOPS on all VB2-based DVB
drivers.
We already have a proper fix, but it sounds safer to keep it being
tested for a while and not hurry, to avoid the risk of another
regression, specially since this is meant to be c/c to stable. So,
for now, let's just revert the broken patch"
* tag 'media/v4.6-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
Revert "[media] videobuf2-v4l2: Verify planes array in buffer dequeueing"
Pull drm fixes from Dave Airlie:
"A bunch of radeon displayport mode setting fixes, and some misc i915
fixes.
There is one revert, the MST audio code in i915 was causing some
oopses, so we've decided just to drop it until next kernel when we can
fix it properly"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: fix DP mode validation
drm/radeon: fix DP mode validation
drm/i915: Bail out of pipe config compute loop on LPT
drm/radeon: fix PLL sharing on DCE6.1 (v2)
drm/radeon: fix DP link training issue with second 4K monitor
Revert "drm/i915: start adding dp mst audio"
drm/i915/bdw: Add missing delay during L3 SQC credit programming
drm/i915/lvds: separate border enable readout from panel fitter
drm/i915: Update CDCLK_FREQ register on BDW after changing cdclk frequency
Pull crypto fix from Herbert Xu:
"This fixes a bug in the RSA self-test that may cause crashes on some
architectures such as SPARC"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: testmgr - Use kmalloc memory for RSA input
Patch 562abd39 "xen-netback: support multiple extra info fragments
passed from frontend" contained a mistake which can result in an in-
correct number of responses being generated when handling errors
encountered when processing packets containing extra info fragments.
This patch fixes the problem.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reported-by: Jan Beulich <JBeulich@suse.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing an OpenStack configuration using VXLANs I saw the following
call trace:
RIP: 0010:[<ffffffff815fad49>] udp4_lib_lookup_skb+0x49/0x80
RSP: 0018:ffff88103867bc50 EFLAGS: 00010286
RAX: ffff88103269bf00 RBX: ffff88103269bf00 RCX: 00000000ffffffff
RDX: 0000000000004300 RSI: 0000000000000000 RDI: ffff880f2932e780
RBP: ffff88103867bc60 R08: 0000000000000000 R09: 000000009001a8c0
R10: 0000000000004400 R11: ffffffff81333a58 R12: ffff880f2932e794
R13: 0000000000000014 R14: 0000000000000014 R15: ffffe8efbfd89ca0
FS: 0000000000000000(0000) GS:ffff88103fd80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000488 CR3: 0000000001c06000 CR4: 00000000001426e0
Stack:
ffffffff81576515 ffffffff815733c0 ffff88103867bc98 ffffffff815fcc17
ffff88103269bf00 ffffe8efbfd89ca0 0000000000000014 0000000000000080
ffffe8efbfd89ca0 ffff88103867bcc8 ffffffff815fcf8b ffff880f2932e794
Call Trace:
[<ffffffff81576515>] ? skb_checksum+0x35/0x50
[<ffffffff815733c0>] ? skb_push+0x40/0x40
[<ffffffff815fcc17>] udp_gro_receive+0x57/0x130
[<ffffffff815fcf8b>] udp4_gro_receive+0x10b/0x2c0
[<ffffffff81605863>] inet_gro_receive+0x1d3/0x270
[<ffffffff81589e59>] dev_gro_receive+0x269/0x3b0
[<ffffffff8158a1b8>] napi_gro_receive+0x38/0x120
[<ffffffffa0871297>] gro_cell_poll+0x57/0x80 [vxlan]
[<ffffffff815899d0>] net_rx_action+0x160/0x380
[<ffffffff816965c7>] __do_softirq+0xd7/0x2c5
[<ffffffff8107d969>] run_ksoftirqd+0x29/0x50
[<ffffffff8109a50f>] smpboot_thread_fn+0x10f/0x160
[<ffffffff8109a400>] ? sort_range+0x30/0x30
[<ffffffff81096da8>] kthread+0xd8/0xf0
[<ffffffff81693c82>] ret_from_fork+0x22/0x40
[<ffffffff81096cd0>] ? kthread_park+0x60/0x60
The following trace is seen when receiving a DHCP request over a flow-based
VXLAN tunnel. I believe this is caused by the metadata dst having a NULL
dev value and as a result dev_net(dev) is causing a NULL pointer dereference.
To resolve this I am replacing the check for skb_dst(skb)->dev with just
skb->dev. This makes sense as the callers of this function are usually in
the receive path and as such skb->dev should always be populated. In
addition other functions in the area where these are called are already
using dev_net(skb->dev) to determine the namespace the UDP packet belongs
in.
Fixes: 63058308cd ("udp: Add udp6_lib_lookup_skb and udp4_lib_lookup_skb")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sunrpc is using SOCKWQ_ASYNC_NOSPACE without setting SOCK_FASYNC,
so the recent optimizations done in sk_set_bit() and sk_clear_bit()
broke it.
There is still the risk that a subsequent sock_fasync() call
would clear SOCK_FASYNC, but sunrpc does not use this yet.
Fixes: 9317bb6982 ("net: SOCKWQ_ASYNC_NOSPACE optimizations")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jiri Pirko <jiri@resnulli.us>
Reported-by: Huang, Ying <ying.huang@intel.com>
Tested-by: Jiri Pirko <jiri@resnulli.us>
Tested-by: Huang, Ying <ying.huang@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
