Make sure the reserved fields, and padding (if any), are
fully initialized.
Based upon a patch by Dan Carpenter and feedback from
Joe Perches.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a VT mode check to make sure VLAN filters are disabled when
in promisc mode and VT is not enabled.
The problem with the previous check was that:
E1000_MRQC_ENABLE_VMDQ is defined as 0x00000003
but when not in VT mode:
mrqc |= E1000_MRQC_ENABLE_RSS_4Q (0x00000002)
So the above check will trigger regardless if VT mode is being used or not.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue with the 82598EB device, where lldpad is causing Tx
Hangs on the card as soon as it attempts to configure DCB for the device. The
adapter will continually Tx hang and reset in a loop.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Stable <stable@vger.kernel.org>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ready bit in the transmit buffer descriptor (TxBD[R])
is previously detected as not set during a prior frame transmission,
then the ENET_TDAR[TDAR] bit is cleared at a later time, even if
additional TxBDs were added to the ring and the ENET_TDAR[TDAR]
bit is set. This results in frames not being transmitted until
there is a 0-to-1 transition on ENET_TDAR[TDAR].
Workarounds:
code can use the transmit frame interrupt flag (ENET_EIR[TXF])
as a method to detect whether the ENET has completed transmission
and the ENET_TDAR[TDAR] has been cleared. If ENET_TDAR[TDAR] is
detected as cleared when packets are queued and waiting for transmit,
then a write to the TDAR bit will restart TxBD processing.
This case main happen when loading is light. A ethernet package may
not send out utile next package put into tx queue.
How to test:
while [ true ]
do
ping <IP> -s 10000 -w 4
ping <IP> -s 6000 -w 2
ping <IP> -s 4000 -w 2
ping <IP> -s 10000 -w 2
done
You will see below result in overnight test.
6008 bytes from 10.192.242.116: seq=1 ttl=128 time=0.722 ms
4008 bytes from 10.192.242.116: seq=0 ttl=128 time=1001.008 ms
4008 bytes from 10.192.242.116: seq=1 ttl=128 time=1.010 ms
10008 bytes from 10.192.242.116: seq=0 ttl=128 time=0.896 ms
After apply this patch, >1000ms delay disappear.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Initialize proper interrupt handler for 83xx.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o When configuring guest VLAN after PVID configuration, VF was loading
with previously configured PVID. Clear the PVID which was previously
configured before configuring guest VLAN.
o Display guest VLAN when it is configured
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Operation type and command type is not set correct in back channel
response.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Work function needs to be initialized before we participate in
inter device communication (IDC).
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ebe7fdbaf3.
This change is not correct. GFP_DMA is not necessary for
this device.
There is some other problem causing this bug.
Signed-off-by: David S. Miller <davem@davemloft.net>
atl1c uses netdev_alloc_skb to refill its rx dma ring, but that call makes no
guarantees about the suitability of the memory for use in DMA. As a result
we've gotten reports of atl1c drivers occasionally hanging and needing to be
reset:
https://bugzilla.kernel.org/show_bug.cgi?id=54021
Fix this by modifying the call to use the internal version __netdev_alloc_skb,
where you can set the gfp_mask explicitly to include GFP_DMA.
Tested by two reporters in the above bug, who have the hardware to validate it.
Both report immediate cessation of the problem with this patch
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Jay Cliburn <jcliburn@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: stable@vger.kernel.org
Tested-by: Luis Henriques <luis.henriques@canonical.com>
Tested-by: Vincent Alquier <vincent.alquier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While EEH error happens, we might not have network device instance
(struct net_device) yet. So we can't access the instance safely and
check its link state, which causes kernel crash. The patch fixes it.
EEH: Frozen PE#2 on PHB#3 detected
EEH: This PCI device has failed 1 times in the last hour
EEH: Notify device drivers to shutdown
(NULL net_device): PCI I/O error detected
Unable to handle kernel paging request for data at address 0x00000048
Faulting instruction address: 0xd00000001c9387a8
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=1024 NUMA PowerNV
:
NIP [d00000001c9387a8] .tg3_io_error_detected+0x78/0x2a0 [tg3]
LR [d00000001c9387a4] .tg3_io_error_detected+0x74/0x2a0 [tg3]
Call Trace:
[c000003f93a0f960] [d00000001c9387a4] .tg3_io_error_detected+0x74/0x2a0 [tg3]
[c000003f93a0fa30] [c00000000003844c] .eeh_report_error+0xac/0x120
[c000003f93a0fac0] [c0000000000371bc] .eeh_pe_dev_traverse+0x8c/0x150
[c000003f93a0fb60] [c000000000038858] .eeh_handle_normal_event+0x128/0x3d0
[c000003f93a0fbf0] [c000000000038db8] .eeh_handle_event+0x2b8/0x2c0
[c000003f93a0fc90] [c000000000038e80] .eeh_event_handler+0xc0/0x170
[c000003f93a0fd30] [c0000000000cc000] .kthread+0xf0/0x100
[c000003f93a0fe30] [c00000000000a0dc] .ret_from_kernel_thread+0x5c/0x80
Reported-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When (integer) sysctl values are expressed in ms and have to be
represented internally as jiffies. The msecs_to_jiffies function
returns an unsigned long, which gets assigned to the integer.
This patch prevents the value to be assigned if bigger than
INT_MAX, done in a similar way as in cba9f3 ("Range checking in
do_proc_dointvec_(userhz_)jiffies_conv").
Signed-off-by: Francesco Fusco <ffusco@redhat.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch, the fields app_solicit, gc_thresh1, gc_thresh2,
gc_thresh3, proxy_qlen, ucast_solicit, mcast_solicit could have
assumed negative values when setting large numbers.
Signed-off-by: Francesco Fusco <ffusco@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAC driver can't work without its associated PHY driver. Reflect
this in the Kconfig options by selecting it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet doesn't support yet SG, so drivers should not advertise SG or TSO
capabilities, as they allow TCP stack to build large TSO packets that
need to be linearized and might use order-5 pages.
This adds an extra copy overhead and possible allocation failures.
Current code ignore skb_linearize() return code so crashes are even
possible.
Best is to not pretend SG/TSO is supported, and add this again when/if
usbnet really supports SG for devices who could get a performance gain.
Based on a prior patch from Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This is another batch of fixes intended for the 3.11 stream. FWIW,
this is the first request with fixes from the mac80211 and iwlwifi
trees as well.
Regarding the mac80211 bits, Johannes says:
"Here I have a fix for RSSI thresholds in mesh, two minstrel fixes from
Felix, an nl80211 fix from Michal and four various fixes I did myself."
As for the iwlwifi bits, Johannes says:
"Here I have a fix for debugfs directory creation (causing a spurious
error message), two scanning fixes from David Spinadel, an LED fix and
two patches related to a BA session problem that eventually caused
firmware crashes from Emmanuel and a small BT fix for older devices as
well as a workaround for a firmware problem with APs with very small
beacon intervals from myself."
Along with those:
Arend van Spriel addresses a lock-up and a NULL pointer dereference
in brcmfmac.
Daniel Drake fixes an unhandled interrupt during device tear down
in mwifiex.
Larry Finger corrects a wil6210 build error.
Oleksij Rempel fixes two ath9k_htc problems related to keeping the
driver and firmware in sync.
Solomon Peachy gives us a cw1200 fix to avoid an oops in monitor mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
build_skb() specifies that the data parameter must come from a kmalloc'd
area, this is only true if frag_size equals 0, because then build_skb()
will use kzsize(data) to figure out the actual data size. Update the
comment to reflect that special condition.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current timeout check is comparing two constant values, so it won't
ever detect a timeout. This patch reworks the affected code a bit so it
has a chance at detecting timeouts correctly.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the <= max condition in the for loop, it will be always go 1
element further than needed. If the condition for the while loop is
never met, then max is MAX_STAT_DEPTH, and for loop will walk off the
end of nodesizes[].
Signed-off-by: Jerry Snitselaar <jerry.snitselaar@oracle.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't dereference "ent" after passing it to free_cmd().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The work queue is initialised in rtl_open (when the interface goes up),
but canceled in rtl_remove_one (when the PCI device gets removed). If
the network interface is not brought up, then the work queue struct is
not initialised. When the device is removed, the attempt to cancel the
uninitialised work queue causes a lockdep warning.
This patch fixes the issue by moving cancel_work_sync to rtl_close (to
match rtl_open). (Note that rtl_close is also called via
unregister_netdev in rtl_remove_one.)
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MODULE_ALIAS, so that auto module loading can work.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Received packets are only scattered if this is enabled in both the
matching filter and the receiving queue. This was not being done for
filters inserted for RFS, so any packet requiring more than a single
descriptor was dropped.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 4bb1667255 (build some drivers only
when compile-testing), PTP_1588_CLOCK_PCH depends on (X86 ||
COMPILE_TEST). But PCH_GBE selects PTP_1588_CLOCK_PCH without
depending on x86. Fix this by adding the same dependency here.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: <fengguang.wu@intel.com> [intel's build test robot]
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: netdev@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: kbuild-all@01.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
The following patchset contains Netfilter fixes for your net tree,
they are:
* Fix potential NULL dereference in the socket match if revision 0
is used, from Eric Dumazet.
* Fix missing expectation NAT initialization that results in dumping
the NAT part via ctnetlink, thus leading to problems in expectation
synchronization through conntrackd, from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid ending up in a NULL-pointer access, the function
brcmf_txflowblock_if() should only be called for interfaces
that have a netdev associated with it.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the transmit fails because there are no hanger slots or
any other reason and the packet was an EAPOL packet the
pending counter should be decreased although it was not
transmitted so the driver does not end up in a dead-lock.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Building driver wil6210 in 3.10 and 3.11 kernels yields the following errors:
CC [M] drivers/net/wireless/ath/wil6210/debugfs.o
drivers/net/wireless/ath/wil6210/debugfs.c: In function 'wil_print_ring':
drivers/net/wireless/ath/wil6210/debugfs.c:163:11: error: pointer targets in passing argument 5 of 'hex_dump_to_buffer' differ in signedness [-Werror=pointer-sign]
false);
^
In file included from include/linux/kernel.h:13:0,
from include/linux/cache.h:4,
from include/linux/time.h:4,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from drivers/net/wireless/ath/wil6210/debugfs.c:17:
include/linux/printk.h:361:13: note: expected 'char *' but argument is of type 'unsigned char *'
extern void hex_dump_to_buffer(const void *buf, size_t len,
^
drivers/net/wireless/ath/wil6210/debugfs.c: In function 'wil_txdesc_debugfs_show':
drivers/net/wireless/ath/wil6210/debugfs.c:429:10: error: pointer targets in passing argument 5 of 'hex_dump_to_buffer' differ in signedness [-Werror=pointer-sign]
sizeof(printbuf), false);
^
In file included from include/linux/kernel.h:13:0,
from include/linux/cache.h:4,
from include/linux/time.h:4,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from drivers/net/wireless/ath/wil6210/debugfs.c:17:
include/linux/printk.h:361:13: note: expected 'char *' but argument is of type 'unsigned char *'
extern void hex_dump_to_buffer(const void *buf, size_t len,
^
cc1: all warnings being treated as errors
make[5]: *** [drivers/net/wireless/ath/wil6210/debugfs.o] Error 1
make[4]: *** [drivers/net/wireless/ath/wil6210] Error 2
make[3]: *** [drivers/net/wireless/ath] Error 2
make[2]: *** [drivers/net/wireless] Error 2
make[1]: *** [drivers/net] Error 2
make: *** [drivers] Error 2
These errors are fixed by changing the type of the buffer from "unsigned char *" to "char *".
Reported-by: Thomas Fjellstrom <thomas@fjellstrom.ca>
Tested-by: Thomas Fjellstrom <thomas@fjellstrom.ca>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.10]
Cc: Thomas Fjellstrom <thomas@fjellstrom.ca>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In monitor mode, priv->vif is NULL, but at one point in the receive path we
blindly attempt to dereference it. Add a test to prevent this.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently ath9k_htc will reboot firmware only if interface was
ever started. Which lead to the problem in case where interface
was never started but module need to be reloaded.
This patch will partially fix bug "ath9k_htc: Target is unresponsive"
https://github.com/qca/open-ath9k-htc-firmware/issues/1
Reproduction case:
- plug adapter
- make sure nothing will touch it. Stop Networkmanager or blacklist mac address of this adapter.
- rmmod ath9k_htc; sleep 1; modprobe ath9k_htc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we configure harwdare and clock, only after
interface start. In this case, if we reload module or
reboot PC without configuring adapter, firmware will freeze.
There is no software way to reset adpter.
This patch add initial configuration and set it in
disabled state, to avoid this freeze. Behaviour of this patch
should be similar to: ifconfig wlan0 up; ifconfig wlan0 down.
Bug: https://github.com/qca/open-ath9k-htc-firmware/issues/1
Tested-by: Bo Shi <cnshibo@gmail.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During tear down (e.g. mwifiex_sdio_remove during system suspend),
mwifiex left IRQs enabled for a significant period of time when it was
unable to handle them correctly. This caused interrupt storms and
interfered with the bluetooth interface on the same SDIO card.
Solve this by disabling interrupts at the point when they can no longer
be handled correctly, which is at the start of mwifiex_remove_card().
For cleanliness, we now enable interrupts in the mwifiex_add_card() path,
to be symmetrical with the disabling of interrupts. We also couple the
registration of the sdio IRQ handler with the actual enable/disable of
interrupts at the hardware level.
I also removed a write to this register in mwifiex_init_sdio which seemed
pointless and won't cause any ill effects now that we only register
the SDIO IRQ handler when we are ready to accept interrupts.
Includes some corrections from Amitkumar Karwar.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville says:
====================
Please accept this batch of fixes intended for the 3.11 tree...
Alexey Khoroshilov fixes a suspend-related race in ath9k_htc.
Arnd Bergmann corrects the alignment of a structure in the ssb code
to be compatible with ARM devices.
Bob Copeland provides an ath5k fix that corrects a mistaken variable
initialization.
Felix Fietkau corrects some frame accounting for dropped frames
in ath9k.
Geert Uytterhoeven brings a Kconfig fix to indicate the DMA
requirements for rt2x00.
Larry Finger offers two rtlwifi fixes: one that properly initializes
a callback; and, a scattered collection of Kconfig, Makefile, and
EXPORT_SYMBOL changes that correct some build problems.
Finally, Sujith Manoharan provides an ath9k fix to disable a feature
on a specific hardware device.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
here are two fixes for the v3.11 release cycle:
Maximilian Schneider contributes a patch for the esd_usb2 CAN driver. It adds
sanity checking to the data coming from the USB CAN adapter before using it.
Alexey Khoroshilov from the Linux Driver Verification project fixes an urb leak
in the error handling of the USB 8dev's usb_8dev_start() function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 9f00b2e7cf ("bridge: only expire the mdb entry when query is
received") added a nasty bug as an active timer can be reinitialized.
setup_timer() must be done once, no matter how many time mod_timer()
is called. br_multicast_new_group() is the right place to do this.
Reported-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Diagnosed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit the min/max value passed to the
/proc/sys/net/ipv4/tcp_syn_retries.
Signed-off-by: Michal Tesar <mtesar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch doesn't change the compiled code because ARC_HDR_SIZE is 4
and sizeof(int) is 4, but the intent was to use the header size and not
the sizeof the header size.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The veth device doesn't provide the vlan features,
so TSO for example is disabled and that causes
performance issues when using tagged traffic.
The test topology looks like this:
br0 br1
/ \ / \
vnet veth0.10 ----- veth1.10 vnet
VM VM
The netperf results with current veth driver:
MIGRATED TCP STREAM TEST from 192.168.1.1 ()
port 0 AF_INET to 192.168.1.2 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.01 2210.22
Now after applying the proposed patch:
MIGRATED TCP STREAM TEST from 192.168.1.1 ()
port 0 AF_INET to 192.168.1.2 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 13067.47
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Clear cached vport vlan variable(vp->vlan) in PF on PCI FLR and
back-channel termination which will allow to configure guest VLAN
on VF after force off/shut down the guest VM.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver was using wrong mask for template version.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Commit b938662d88
("qlcnic: Fix ethtool supported port status for 83xx")
introduced regression for display of link status for 83xx
adapter while refactoring port status display. This patch
is to fix the link status display for 83xx adapter.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o "qlcnic_sriov" structure pointer should be accessed only
when SR-IOV is enabled. Access this pointer after SR-IOV
PF check.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
