In such a way that vcs and vcs2 are just two different instances (0 and 1)
of the same engine class (VIDEO_DECODE_CLASS).
v2: Align the instance types (Tvrtko)
v3: Don't use enums for bspec-defined stuff (Michal)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491834873-9345-2-git-send-email-oscar.mateo@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Geminilake platform sports a native HDMI 2.0 controller, and is
capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec
mendates scrambling for these higher clocks, for reduced RF footprint.
This patch checks if the monitor supports scrambling, and if required,
enables it during the modeset.
V2: Addressed review comments from Ville:
- Do not track scrambling status in DRM layer, track somewhere in
driver like in intel_crtc_state.
- Don't talk to monitor at such a low layer, set monitor scrambling
in intel_enable_ddi() before enabling the port.
V3: Addressed review comments from Jani
- In comments, function names, use "sink" instead of "monitor",
so that the implementation could be close to the language of
HDMI spec.
V4: Addressed review comment from Maarten
- scrambling -> hdmi_scrambling
- high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio
V5: Addressed review comments from Ville and Ander
- Do not modifiy the crtc_state after compute_config. Move all
scrambling and tmds_clock_ratio calcutations to compute_config.
- While setting scrambling for source/sink, do not check the
conditions again, just go by the crtc_state flags. This will
simplyfy the condition checks.
V6: Addressed review comments from Ville
- Do not add IS_GLK check in disable/enable function, instead add it
in compute_config, while setting state flags.
- Remove unnecessary paranthesis.
- Simplyfy handle_sink_scrambling function as suggested.
- Add readout code for scrambling status in get_ddi_config and add a
check for the same in pipe_config_compare.
V7: Addressed review comments from Ander/Ville
- No separate function for source scrambling, make it inline
- Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK
- Do not add platform check while setting source scrambling
- Use pipe_config instead of crtc->config to set sink scrambling
- To readout scrambling status, Compare with SCRAMBLING_MASK
not any of its bits
- Remove platform check in intel_pipe_config_compare while checking
scrambling status
V8: Fixed mege conflict, Addressed review comments from Ander
- Remove the desciption/comment about scrambling fom the caller, move
it to the function
- Move the IS_GLK check into scrambling function
- Fix alignment
V9: Fixed review comments from Ville, Ander
- Pass the scrambling state variables as bool input to the sink_scrambling
function and let the disable call be unconditional.
- Fix alignments in function calls and debug messages.
- Add kernel doc for function intel_hdmi_handle_sink_scrambling
V10: Rebase
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489404244-16608-6-git-send-email-shashank.sharma@intel.com
We have used cz timestamp register to gain a reference time wrt
to residency calculations. The residency counts are in cz clk ticks
(333Mhz clock) but for some reason the cz timestamp register gives
100us units. Perhaps for some other usage, the base-ten based values
are easier, but in residency calculations raw units would have been
the easiest.
As there is not much advantage of using base-ten clock through
a more costly punit access, take our reference times directly from
kernel clock.
v2: use ktime (Chris, Ville)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The REDIRECT_TO_GUC bit is a strange beast as it is a disable bit -
setting the bit in the pm interrupt generation stops the interrupt going
to the guc (not sending it to the guc as the name implies). To help the
reader rename it to DISABLE_REDIRECT_TO_GUC so that we keep the bspec
greppable name without it being as confusing!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170312132745.9618-1-chris@chris-wilson.co.uk
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Driver needs to ensure that it doesn't mask the PM interrupts, which are
unmasked/needed by GuC firmware. For that, Driver maintains a bitmask of
interrupts to be kept unmasked, pm_intr_keep.
pm_intr_keep was determined across GuC load. GuC gets loaded in different
scenarios and it is not going to change the pm_intr_keep so this patch
moves its setup to intel_irq_init.
This patch fixes incorrect RPS masking leading to UP interrupts triggered
even when at cur_freq=max and inversly for Down interrupts.
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1488862355-9768-1-git-send-email-sagar.a.kamble@intel.com
4 weeks worth of stuff since I was traveling&lazy:
- lspcon improvements (Imre)
- proper atomic state for cdclk handling (Ville)
- gpu reset improvements (Chris)
- lots and lots of polish around fences, requests, waiting and
everything related all over (both gem and modeset code), from Chris
- atomic by default on gen5+ minus byt/bsw (Maarten did the patch to
flip the default, really this is a massive joint team effort)
- moar power domains, now 64bit (Ander)
- big pile of in-kernel unit tests for various gem subsystems (Chris),
including simple mock objects for i915 device and and the ggtt
manager.
- i915_gpu_info in debugfs, for taking a snapshot of the current gpu
state. Same thing as i915_error_state, but useful if the kernel didn't
notice something is stick. From Chris.
- bxt dsi fixes (Umar Shankar)
- bxt w/a updates (Jani)
- no more struct_mutex for gem object unreference (Chris)
- some execlist refactoring (Tvrtko)
- color manager support for glk (Ander)
- improve the power-well sync code to better take over from the
firmware (Imre)
- gem tracepoint polish (Tvrtko)
- lots of glk fixes all around (Ander)
- ctx switch improvements (Chris)
- glk dsi support&fixes (Deepak M)
- dsi fixes for vlv and clanups, lots of them (Hans de Goede)
- switch to i915.ko types in lots of our internal modeset code (Ander)
- byt/bsw atomic wm update code, yay (Ville)
* tag 'drm-intel-next-2017-03-06' of git://anongit.freedesktop.org/git/drm-intel: (432 commits)
drm/i915: Update DRIVER_DATE to 20170306
drm/i915: Don't use enums for hardware engine id
drm/i915: Split breadcrumbs spinlock into two
drm/i915: Refactor wakeup of the next breadcrumb waiter
drm/i915: Take reference for signaling the request from hardirq
drm/i915: Add FIFO underrun tracepoints
drm/i915: Add cxsr toggle tracepoint
drm/i915: Add VLV/CHV watermark/FIFO programming tracepoints
drm/i915: Add plane update/disable tracepoints
drm/i915: Kill level 0 wm hack for VLV/CHV
drm/i915: Workaround VLV/CHV sprite1->sprite0 enable underrun
drm/i915: Sanitize VLV/CHV watermarks properly
drm/i915: Only use update_wm_{pre,post} for pre-ilk platforms
drm/i915: Nuke crtc->wm.cxsr_allowed
drm/i915: Compute proper intermediate wms for vlv/cvh
drm/i915: Skip useless watermark/FIFO related work on VLV/CHV when not needed
drm/i915: Compute vlv/chv wms the atomic way
drm/i915: Compute VLV/CHV FIFO sizes based on the PM2 watermarks
drm/i915: Plop vlv/chv fifo sizes into crtc state
drm/i915: Plop vlv wm state into crtc_state
...
Generally we are using macros for any hardware identifiers as these
may change between Gens. Do the same with hardware engine ids.
v2: move hw engine defs to i915_reg.h (Chris)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301202615.118632-1-michal.wajdeczko@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
drivers/gpu/drm/i915/intel_dsi.c: In function ‘intel_dsi_prepare’:
drivers/gpu/drm/i915/intel_dsi.c:1308:1: error: the frame size of 2488 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
which is caused by the compiling expanding every _MIPI_PORT into an
on-stack array of u32[3] at every callsite. Not sure why only one
machine/compiler appears susceptible, but with a minor tweak to _MIPI_PORT
we can defer the error until later.
This is a partial revert of commit ce64645d86 ("drm/i915: use variadic
macros and arrays to choose port/pipe based registers") for a particular
bad offender.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170228145519.18012-1-chris@chris-wilson.co.uk
Acked-by: Jani Nikula <jani.nikula@intel.com>
v2: Addressed Jani's Review comments(renamed bit field macros)
Txesc clock divider is calculated and programmed
for geminilake platform.
Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487335415-14766-7-git-send-email-madhav.chauhan@intel.com
PLL divider range for GLK is different than that of
BXT, hence adding the GLK range check in this patch.
v2: Code restructure using min and max ratio variables (Ander)
v3: Code changes to avoid "maybe-uninitialized" warning (Jani)
Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487335415-14766-5-git-send-email-madhav.chauhan@intel.com
Program the clk lane and tlpx time count registers
to configure DSI PHY.
v2: Addressed Jani's Review comments(renamed bit field macros)
v3: Program clk lane timing reg same as dphy param reg.
v4: Removed "line over 80 character" warning
Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487335415-14766-3-git-send-email-madhav.chauhan@intel.com
-----BEGIN PGP SIGNATURE-----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=Yjfg
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.11.
Nothing too major, the tinydrm and mmu-less support should make
writing smaller drivers easier for some of the simpler platforms, and
there are a bunch of documentation updates.
Intel grew displayport MST audio support which is hopefully useful to
people, and FBC is on by default for GEN9+ (so people know where to
look for regressions). AMDGPU has a lot of fixes that would like new
firmware files installed for some GPUs.
Other than that it's pretty scattered all over.
I may have a follow up pull request as I know BenH has a bunch of AST
rework and fixes and I'd like to get those in once they've been tested
by AST, and I've got at least one pull request I'm just trying to get
the author to fix up.
Core:
- drm_mm reworked
- Connector list locking and iterators
- Documentation updates
- Format handling rework
- MMU-less support for fbdev helpers
- drm_crtc_from_index helper
- Core CRC API
- Remove drm_framebuffer_unregister_private
- Debugfs cleanup
- EDID/Infoframe fixes
- Release callback
- Tinydrm support (smaller drivers for simple hw)
panel:
- Add support for some new simple panels
i915:
- FBC by default for gen9+
- Shared dpll cleanups and docs
- GEN8 powerdomain cleanup
- DMC support on GLK
- DP MST audio support
- HuC loading support
- GVT init ordering fixes
- GVT IOMMU workaround fix
amdgpu/radeon:
- Power/clockgating improvements
- Preliminary SR-IOV support
- TTM buffer priority and eviction fixes
- SI DPM quirks removed due to firmware fixes
- Powerplay improvements
- VCE/UVD powergating fixes
- Cleanup SI GFX code to match CI/VI
- Support for > 2 displays on 3/5 crtc asics
- SI headless fixes
nouveau:
- Rework securre boot code in prep for GP10x secure boot
- Channel recovery improvements
- Initial power budget code
- MMU rework preperation
vmwgfx:
- Bunch of fixes and cleanups
exynos:
- Runtime PM support for MIC driver
- Cleanups to use atomic helpers
- UHD Support for TM2/TM2E boards
- Trigger mode fix for Rinato board
etnaviv:
- Shader performance fix
- Command stream validator fixes
- Command buffer suballocator
rockchip:
- CDN DisplayPort support
- IOMMU support for arm64 platform
imx-drm:
- Fix i.MX5 TV encoder probing
- Remove lower fb size limits
msm:
- Support for HW cursor on MDP5 devices
- DSI encoder cleanup
- GPU DT bindings cleanup
sti:
- stih410 cleanups
- Create fbdev at binding
- HQVDP fixes
- Remove stih416 chip functionality
- DVI/HDMI mode selection fixes
- FPS statistic reporting
omapdrm:
- IRQ code cleanup
dwi-hdmi bridge:
- Cleanups and fixes
adv-bridge:
- Updates for nexus
sii8520 bridge:
- Add interlace mode support
- Rework HDMI and lots of fixes
qxl:
- probing/teardown cleanups
ZTE drm:
- HDMI audio via SPDIF interface
- Video Layer overlay plane support
- Add TV encoder output device
atmel-hlcdc:
- Rework fbdev creation logic
tegra:
- OF node fix
fsl-dcu:
- Minor fixes
mali-dp:
- Assorted fixes
sunxi:
- Minor fix"
[ This was the "fixed" pull, that still had build warnings due to people
not even having build tested the result. I'm not a happy camper
I've fixed the things I noticed up in this merge. - Linus ]
* tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux: (1177 commits)
lib/Kconfig: make PRIME_NUMBERS not user selectable
drm/tinydrm: helpers: Properly fix backlight dependency
drm/tinydrm: mipi-dbi: Fix field width specifier warning
drm/tinydrm: mipi-dbi: Silence: ‘cmd’ may be used uninitialized
drm/sti: fix build warnings in sti_drv.c and sti_vtg.c files
drm/amd/powerplay: fix PSI feature on Polars12
drm/amdgpu: refuse to reserve io mem for split VRAM buffers
drm/ttm: fix use-after-free races in vm fault handling
drm/tinydrm: Add support for Multi-Inno MI0283QT display
dt-bindings: Add Multi-Inno MI0283QT binding
dt-bindings: display/panel: Add common rotation property
of: Add vendor prefix for Multi-Inno
drm/tinydrm: Add MIPI DBI support
drm/tinydrm: Add helper functions
drm: Add DRM support for tiny LCD displays
drm/amd/amdgpu: post card if there is real hw resetting performed
drm/nouveau/tmr: provide backtrace when a timeout is hit
drm/nouveau/pci/g92: Fix rearm
drm/nouveau/drm/therm/fan: add a fallback if no fan control is specified in the vbios
drm/nouveau/hwmon: expose power_max and power_crit
..
Following a reset, the context and page directory registers are lost.
However, the queue of requests that we resubmit after the reset may
depend upon them - the registers are restored from a context image, but
that restore may be inhibited and may simply be absent from the request
if it was in the middle of a sequence using the same context. If we
prime the CCID/PD registers with the first request in the queue (even
for the hung request), we prevent invalid memory access for the
following requests (and continually hung engines).
v2: Magic BIT(8), reserved for future use but still appears unused.
v3: Some commentary on handling innocent vs guilty requests
v4: Add a wait for PD_BASE fetch. The reload appears to be instant on my
Ivybridge, but this bit probably exists for a reason.
Fixes: 821ed7df6e ("drm/i915: Update reset path to fix incomplete requests")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207152437.4252-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
(cherry picked from commit c0dcb203fb)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Once the address space has been created (using 3 or 4 levels of page
tables), we should use that to program the appropriate type into the
contexts. This gives us the flexibility to handle different types of
address spaces at runtime.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170209144036.23664-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Following a reset, the context and page directory registers are lost.
However, the queue of requests that we resubmit after the reset may
depend upon them - the registers are restored from a context image, but
that restore may be inhibited and may simply be absent from the request
if it was in the middle of a sequence using the same context. If we
prime the CCID/PD registers with the first request in the queue (even
for the hung request), we prevent invalid memory access for the
following requests (and continually hung engines).
v2: Magic BIT(8), reserved for future use but still appears unused.
v3: Some commentary on handling innocent vs guilty requests
v4: Add a wait for PD_BASE fetch. The reload appears to be instant on my
Ivybridge, but this bit probably exists for a reason.
Fixes: 821ed7df6e ("drm/i915: Update reset path to fix incomplete requests")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207152437.4252-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
The audio chicken bit (register offset 0x62f38) seems required to make
DP audio working on some machines. At least, on Dell Wyse 3040, I
failed to get the audio unless this bit is set once.
Strangely, the bit seems necessary only once, and it persists after
that, even some power-off cycles. The register is supposedly
write-only, so it's no evidence whether the bit keeps effect
persistently. But, judging from the experiment, it looks enough to
set it up once at the device initialization.
The patch is basically a cut from the original patch by Pierre-Louis
Bossart.
v1->v2: drop read since it's a write-only reg.
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable unmute/mute amp notification. This doesn't seem to affect
HDMI support so this is done unconditionally.
An earlier version of this patch set a chicken bit at address 0x62F38
prior to the mute/unmute but this register doesn't seem to do anything
so this phase was removed.
v1->v2: Drop needless pipe A check, avoid temporary reg offset variable.
v2->v3: Add "_" prefix to VLV_AUD_PORT_EN_X_DBG as they are internal.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable MIPI IO WA for BXT DSI as per bspec and
program the DSI regulators.
v2: Moved IO enable to pre-enable as per Mika's
review comments. Also reused the existing register
definition for BXT_P_CR_GT_DISP_PWRON.
v3: Added Programming the DSI regulators as per disable/enable
sequences.
v4: Restricting regulator changes to BXT as suggested by
Jani/Mika
v5: Removed redundant read/modify for regulator register as
per Jani's comment. Maintain enable/disable symmetry as per spec.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Vidya Srinivas <vidya.srinivas@intel.com>
Acked-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485353603-11260-1-git-send-email-vidya.srinivas@intel.com
This allows the use of more than 3 ports/pipes/whatever without tricks,
even if the register offsets are not evenly spaced.
There's the risk of out of bounds access if we're not careful; currently
that would "just" lead to the wrong register offset being used. It might
be possible to add build bug ons for build time constant indexing.
We already have ports defined up to E, not sure if we might have bugs
related to them and the current _PORT3() macro.
text data bss dec hex filename
1239868 46199 4096 1290163 13afb3 drivers/gpu/drm/i915/i915.ko
1238828 46199 4096 1289123 13aba3 drivers/gpu/drm/i915/i915.ko
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Tvrtko Ursulin <tursulin@ursulin.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485532626-20923-1-git-send-email-jani.nikula@intel.com
Move the invariant parts of context desc setup from execlist init
to context creation. This is advantageous when we need to
create different templates based on the context parametrization,
ie. for svm capable contexts.
v2: s/create/default, remove engine->ctx_desc_template
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485522189-31984-1-git-send-email-mika.kuoppala@intel.com
The gamma tables in Geminilake were changed. There is no split-gamma
mode. Instead, there is a dedicated degamma table that is enabled
whenever pipe CSC is enabled.
The dedicated gamma table has 16 bit precision but doesn't support
separate channels. Since that doesn't match the per-channel format of
the degamma LUT property, for now only a linear table is loaded and the
property ignored.
v2: Remove empty line. (Ville)
Reuse broadwell code. (Ville)
v3: Don't write PIPE_CSC_MODE. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170127090230.20302-1-ander.conselvan.de.oliveira@intel.com
In Geminilake, the bits for enabling pipe csc, pipe gamma and plane
gamma moved to a new register. So update the plane update functions
to set the right bits.
Pipe CSC is kept disabled though, since enabling that also enables the
dedicated degamma table, and that is not properly programmed yet,
leading to a black screen.
v2: Use plane_id. (Ville)
Remove unnecessary variable. (Ville)
Keep registers in offset order. (Ville)
Don't set plane gamma disable twice. (Ander)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485429865-10687-3-git-send-email-ander.conselvan.de.oliveira@intel.com
Enable support for HDMI LPE audio mode on Baytrail and
Cherrytrail when HDaudio controller is not detected
Setup minimum required resources during i915_driver_load:
1. Create a platform device to share MMIO/IRQ resources
2. Make the platform device child of i915 device for runtime PM.
3. Create IRQ chip to forward HDMI LPE audio irqs.
HDMI LPE audio driver (a standalone sound driver) probes the
LPE audio device and creates a new sound card.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Jerome Anand <jerome.anand@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reports live state of PSR2 form PSR2_STATUS register.
bit field 31:28 gives the live state of PSR2.
It can be used to check if system is in deep sleep,
selective update or selective update standby.
During video play back, we can use this to check
if system is entering SU mode or not.
when system is in idle state, DEEP_SLEEP(8) must be entered.
When video playback is happening, system must be in
SLEEP(3 / selective update) or SU_STANDBY( 6 / selective update standby)
v2: (Rodrigo)
- Remove EDP_PSR2_STATUS_TG_ON=a ,instead use ARRAY_SIZE
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Patil Deepti <deepti.patil@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1483720352-24761-1-git-send-email-vathsala.nagaraju@intel.com
Program EDP_PSR_DEBUG_CTL (PSR_MASK) to enable system
to go to deep sleep while in psr2.PSR2_STATUS bit 31:28
should report value 8 , if system enters deep sleep state.
Also, EDP_FRAMES_BEFORE_SU_ENTRY is set 1 , if not set,
flickering is observed on psr2 panel.
v2: (Ilia Mirkin)
- Remove duplicate bit definition 25:27
v3: rebase
v4: rebase
v5: rebase
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Patil Deepti <deepti.patil@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484267484-21843-1-git-send-email-vathsala.nagaraju@intel.com
As per bpsec, CHICKEN_TRANS_EDP bit 12 ,15 must be programmed in
psr2 enable sequence.
bit 12 : Program Transcoder EDP VSC DIP header with a valid setting for
PSR2 and Set CHICKEN_TRANS_EDP(0x420cc) bit 12 for programmable
header packet.
bit 15 : Set CHICKEN_TRANS_EDP(0x420cc) bit 15 if Y coordinate is supported
v2: (Rodrigo)
- move CHICKEN_TRANS_EDP bit set logic right after setup_vsc
v3:(Rodrigo)
- initialize chicken_trans to CHICKEN_TRANS_BIT12 instead of 0
v4:(chris wilson)
- use BIT(12), remove CHICKEN_TRANS_BIT12
- remove unnecessary comments
- update commit message
v5:
- rename bit 12 PSR2_VSC_ENABLE_PROG_HEADER
- rename bit 15 PSR2_ADD_VERTICAL_LINE_COUNT
v6:(Rodrigo)
- remove TRANS_EDP=3, use cpu_transcoder
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: vathsala nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Patil Deepti <deepti.patil@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484247691-20930-1-git-send-email-vathsala.nagaraju@intel.com
Psr1 and psr2 are mutually exclusive,ie when psr2 is enabled,
psr1 should be disabled.When psr2 is exited , bit 31 of reg
PSR2_CTL must be set to 0 but currently bit 31 of SRD_CTL
(psr1 control register)is set to 0.
Also ,PSR2_IDLE state is looked up from SRD_STATUS(psr1 register)
instead of PSR2_STATUS register, which has wrong data, resulting
in blankscreen.
hsw_enable_source is split into hsw_enable_source_psr1 and
hsw_enable_source_psr2 for easier code review and maintenance,
as suggested by rodrigo and jim.
v2: (Rodrigo)
- Rename hsw_enable_source_psr* to intel_enable_source_psr*
v3: (Rodrigo)
- In hsw_psr_disable ,
1) for psr active case, handle psr2 followed by psr1.
2) psr inactive case, handle psr2 followed by psr1
v4:(Rodrigo)
- move psr2 restriction(32X20) to match_conditions function
returning false and fully blocking PSR to a new patch before
this one.
v5: in source_psr2, removed val = EDP_PSR_ENABLE
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Patil Deepti <deepti.patil@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484244059-9201-1-git-send-email-vathsala.nagaraju@intel.com
BSpec says:
"Overlay Clock Gating Must be Disabled: Overlay & L2 Cache clock gating
must be disabled in order to prevent device hangs when turning off overlay.SW
must turn off Ovrunit clock gating (6200h) and L2 Cache clock gating (C8h)."
We only turned off the overlay clock gating (due to lack of docs I
presume). After a bit of experimentation it looks like the the magic
C8h register lives in the PCI config space of device 0, and the magic
bit appears to be bit 2. Or at the very least this eliminates the GPU
death after MI_OVERLAY_OFF.
L2 clock gating seems to save ~80mW, so let's keep it on unless we need
to actually use the overlay.
Also let's move the OVRUNIT clock gating to the same place since we can,
and 845 supposedly doesn't need it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481131693-27993-11-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Follow the PLL enable sequence updated in bspec, which requires the DCC
delay range 2 bit to be set.
v2: Moved from DDI init sequence to PLL enable.
v3: Don't read value from GRP register. (Rodrido)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480667037-11215-5-git-send-email-ander.conselvan.de.oliveira@intel.com
Geminilake is mostly backwards compatible with broxton, so change most
of the IS_BROXTON() checks to IS_GEN9_LP(). Differences between the
platforms will be implemented in follow-up patches.
v2: Don't reuse broxton's path in intel_update_max_cdclk().
Don't set plane count as in broxton.
v3: Rebase
v4: Include the check intel_bios_is_port_hpd_inverted().
Commit message.
v5: Leave i915_dmc_info() out; glk's csr version != bxt's. (Rodrigo)
v6: Rebase.
v7: Convert a few mode IS_BROXTON() occurances in pps, ddi, dsi and pll
code. (Rodrigo)
v8: Squash a couple of DDI patches with more conversions. (Rodrigo)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480667037-11215-2-git-send-email-ander.conselvan.de.oliveira@intel.com
Doing cmd_header >> 29 to extract our 3-bit client value where we know
cmd_header is a u32 shouldn't then also require the use of a mask. So
remove the redundant operation and get rid of INSTR_CLIENT_MASK now that
there are no longer any users.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479163174-29686-1-git-send-email-matthew.auld@intel.com
Use intel_plane->id to derive the VLV/CHV sprite register offsets
instead of abusing plane->plane which is really meant to for
primary planes only.
v2: Convert assert_sprites_disabled() over as well
v3: Rename the reg macro parameter to 'plane_id' as well (Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479830524-7882-6-git-send-email-ville.syrjala@linux.intel.com
Gen graphics hardware can be set up to periodically write snapshots of
performance counters into a circular buffer via its Observation
Architecture and this patch exposes that capability to userspace via the
i915 perf interface.
v2:
Make sure to initialize ->specific_ctx_id when opening, without
relying on _pin_notify hook, in case ctx already pinned.
v3:
Revert back to pinning ctx upfront when opening stream, removing
need to hook in to pinning and to update OACONTROL on the fly.
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Sourab Gupta <sourab.gupta@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161107194957.3385-7-robert@sixbynine.org
OACONTROL changes quite a bit for gen8, with some bits split out into a
per-context OACTXCONTROL register. Rename now before adding more gen7 OA
registers
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Sourab Gupta <sourab.gupta@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161107194957.3385-3-robert@sixbynine.org
Decoupled MMIO is an alternative way to access forcewake domain
registers, which requires less cycles for a single read/write and
avoids frequent software forcewake.
This certainly gives advantage over the forcewake as this new
mechanism “decouples” CPU cycles and allow them to complete even
when GT is in a CPD (frequency change) or C6 state.
This can co-exist with forcewake and we will continue to use forcewake
as appropriate. E.g. 64-bit register writes to avoid writing 2 dwords
separately and land into funny situations.
v2:
- Moved platform check out of the function and got rid of duplicate
functions to find out decoupled power domain (Chris)
- Added a check for forcewake already held and skipped decoupled
access (Chris)
- Skipped writing 64 bit registers through decoupled MMIO (Chris)
v3:
- Improved commit message with more info on decoupled mmio (Tvrtko)
- Changed decoupled operation to enum and used u32 instead of
uint_32 data type for register offset (Tvrtko)
- Moved HAS_DECOUPLED_MMIO to device info (Tvrtko)
- Added lookup table for converting fw_engine to pd_engine (Tvrtko)
- Improved __gen9_decoupled_read and __gen9_decoupled_write
routines (Tvrtko)
v4:
- Fixed alignment and variable names (Chris)
- Write GEN9_DECOUPLED_REG0_DW1 register in just one go (Zhe Wang)
v5:
- Changed HAS_DECOUPLED_MMIO() argument name to dev_priv (Tvrtko)
- Sanitize info->had_decoupled_mmio at init (Chris)
Signed-off-by: Zhe Wang <zhe1.wang@intel.com>
Signed-off-by: Praveen Paneri <praveen.paneri@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479230360-22395-1-git-send-email-praveen.paneri@intel.com
The port registers related to the phys in broxton map to different
channels and specific phys. Make that mapping explicit.
v2: Pass enum dpio_phy to macros instead of mmio base. (Imre)
v3: Fix typo in macros. (Imre)
v4: Also change variables from u32 to enum dpio_phy. (Imre)
Remove leftovers from previous version. (Imre)
v5: Actually git add the changes.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1476863940-6019-1-git-send-email-ander.conselvan.de.oliveira@intel.com
When modeset occurs and the LS_CLK is set to some special values in DP
mode, the N/M need to be set manually if audio is playing. Otherwise the
first several seconds may be silent in audio playback.
The relationship of Maud and Naud is expressed in the following
equation:
Maud/Naud = 512 * fs / f_LS_Clk
Please refer VESA DisplayPort Standard spec for details.
v2 by Jani:
- organize Maud/Naud table according to DP 1.4 spec
- add 64k and 128k audio rates
- update HSW_AUD_M_CTS_ENABLE register when Maud not found
- remove extra checks for port clock
- simplify Maud/Naud lookup
- reset patch author back to Libin
Cc: "Zhang, Keqiao" <keqiao.zhang@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: "Lin, Mengdong" <mengdong.lin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477407258-30599-3-git-send-email-jani.nikula@intel.com
There are certain types of interrupts which Host can receive from GuC.
GuC ukernel sends an interrupt to Host for certain events, like for
example retrieve/consume the logs generated by ukernel.
This patch adds support to receive interrupts from GuC but currently
enables & partially handles only the interrupt sent by GuC ukernel.
Future patches will add support for handling other interrupt types.
v2:
- Use common low level routines for PM IER/IIR programming (Chris)
- Rename interrupt functions to gen9_xxx from gen8_xxx (Chris)
- Replace disabling of wake ref asserts with rpm get/put (Chris)
v3:
- Update comments for more clarity. (Tvrtko)
- Remove the masking of GuC interrupt, which was kept masked till the
start of bottom half, its not really needed as there is only a
single instance of work item & wq is ordered. (Tvrtko)
v4:
- Rebase.
- Rename guc_events to pm_guc_events so as to be indicative of the
register/control block it is associated with. (Chris)
- Add handling for back to back log buffer flush interrupts.
v5:
- Move the read & clearing of register, containing Guc2Host message
bits, outside the irq spinlock. (Tvrtko)
v6:
- Move the log buffer flush interrupt related stuff to the following
patch so as to do only generic bits in this patch. (Tvrtko)
- Rebase.
v7:
- Remove the interrupts_enabled check from gen9_guc_irq_handler, want to
process that last interrupt also before disabling the interrupt, sync
against the work queued by irq handler will be done by caller disabling
the interrupt.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Remove never used BSM{,_MASK}. BSM_MASK #define also causes a warning.
include/drm/i915_drm.h:96:34: warning: result of ‘65535 << 20’
requires 37 bits to represent, but ‘int’ only has 32 bits
[-Wshiftoverflow=]
#define INTEL_BSM_MASK (0xFFFF << 20)
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1476256734-6457-1-git-send-email-joonas.lahtinen@linux.intel.com
