Per binding doc fsl,aips-bus.yaml, compatible and reg is
required. And for reg, the AIPS configuration space should be
used, not all the AIPS bus space.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It was based on Google Source Code for Coral Edge TPU Mendel release:
https://coral.googlesource.com/linux-imx/
It was tested on Coral Dev Board using this command:
sudo stress --cpu 4 --timeout 3600
Signed-off-by: Vitor Massaru Iha <vitor@massaru.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "pinctrl" instead of "iomuxc"
for all i.MX8M SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8MM, the SNVS requires a clock. This is similar to the clock
bound to the SNVS RTC node, but if the SNVS RTC driver isn't enabled,
then SNVS doesn't work, and as such the pwrkey driver doesn't
work (i.e. hangs the kernel, as the clock isn't enabled).
Also see commit ec2a844ef7
("ARM: dts: imx7s: add snvs rtc clock")
for a similar fix.
Signed-off-by: André Draszik <git@andred.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no binding doc for these compatible string
"fsl,imx8mq-aips-bus" and "fsl,aips-bus", "simple-bus" is enough
for aips usage, so drop the upper two.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently only SAI2 is present in the DT. Add all the other SAI
instances present on the SoC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The NOC clock defaults to 400 MHz. Increase it to 800 MHz for improved
memory performance.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is used by the imx-ddrc devfreq driver to implement dynamic
frequency scaling of DRAM.
Support for proactive scaling via interconnect will come later. The
high-performance bus masters which need that (display, vpu, gpu) are
mostly not yet enabled in upstream anyway.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8MQ, usdhc's ipg clock is from IMX8MQ_CLK_IPG_ROOT,
assign it explicitly instead of using IMX8MQ_CLK_DUMMY.
Fixes: 748f908cc8 ("arm64: add basic DTS for i.MX8MQ")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Temperature and hysteresis were picked after the CPU.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull crypto updates from Herbert Xu:
"API:
- Add the ability to abort a skcipher walk.
Algorithms:
- Fix XTS to actually do the stealing.
- Add library helpers for AES and DES for single-block users.
- Add library helpers for SHA256.
- Add new DES key verification helper.
- Add surrounding bits for ESSIV generator.
- Add accelerations for aegis128.
- Add test vectors for lzo-rle.
Drivers:
- Add i.MX8MQ support to caam.
- Add gcm/ccm/cfb/ofb aes support in inside-secure.
- Add ofb/cfb aes support in media-tek.
- Add HiSilicon ZIP accelerator support.
Others:
- Fix potential race condition in padata.
- Use unbound workqueues in padata"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (311 commits)
crypto: caam - Cast to long first before pointer conversion
crypto: ccree - enable CTS support in AES-XTS
crypto: inside-secure - Probe transform record cache RAM sizes
crypto: inside-secure - Base RD fetchcount on actual RD FIFO size
crypto: inside-secure - Base CD fetchcount on actual CD FIFO size
crypto: inside-secure - Enable extended algorithms on newer HW
crypto: inside-secure: Corrected configuration of EIP96_TOKEN_CTRL
crypto: inside-secure - Add EIP97/EIP197 and endianness detection
padata: remove cpu_index from the parallel_queue
padata: unbind parallel jobs from specific CPUs
padata: use separate workqueues for parallel and serial work
padata, pcrypt: take CPU hotplug lock internally in padata_alloc_possible
crypto: pcrypt - remove padata cpumask notifier
padata: make padata_do_parallel find alternate callback CPU
workqueue: require CPU hotplug read exclusion for apply_workqueue_attrs
workqueue: unconfine alloc/apply/free_workqueue_attrs()
padata: allocate workqueue internally
arm64: dts: imx8mq: Add CAAM node
random: Use wait_event_freezable() in add_hwgenerator_randomness()
crypto: ux500 - Fix COMPILE_TEST warnings
...
Pull core timer updates from Thomas Gleixner:
"Timers and timekeeping updates:
- A large overhaul of the posix CPU timer code which is a preparation
for moving the CPU timer expiry out into task work so it can be
properly accounted on the task/process.
An update to the bogus permission checks will come later during the
merge window as feedback was not complete before heading of for
travel.
- Switch the timerqueue code to use cached rbtrees and get rid of the
homebrewn caching of the leftmost node.
- Consolidate hrtimer_init() + hrtimer_init_sleeper() calls into a
single function
- Implement the separation of hrtimers to be forced to expire in hard
interrupt context even when PREEMPT_RT is enabled and mark the
affected timers accordingly.
- Implement a mechanism for hrtimers and the timer wheel to protect
RT against priority inversion and live lock issues when a (hr)timer
which should be canceled is currently executing the callback.
Instead of infinitely spinning, the task which tries to cancel the
timer blocks on a per cpu base expiry lock which is held and
released by the (hr)timer expiry code.
- Enable the Hyper-V TSC page based sched_clock for Hyper-V guests
resulting in faster access to timekeeping functions.
- Updates to various clocksource/clockevent drivers and their device
tree bindings.
- The usual small improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (101 commits)
posix-cpu-timers: Fix permission check regression
posix-cpu-timers: Always clear head pointer on dequeue
hrtimer: Add a missing bracket and hide `migration_base' on !SMP
posix-cpu-timers: Make expiry_active check actually work correctly
posix-timers: Unbreak CONFIG_POSIX_TIMERS=n build
tick: Mark sched_timer to expire in hard interrupt context
hrtimer: Add kernel doc annotation for HRTIMER_MODE_HARD
x86/hyperv: Hide pv_ops access for CONFIG_PARAVIRT=n
posix-cpu-timers: Utilize timerqueue for storage
posix-cpu-timers: Move state tracking to struct posix_cputimers
posix-cpu-timers: Deduplicate rlimit handling
posix-cpu-timers: Remove pointless comparisons
posix-cpu-timers: Get rid of 64bit divisions
posix-cpu-timers: Consolidate timer expiry further
posix-cpu-timers: Get rid of zero checks
rlimit: Rewrite non-sensical RLIMIT_CPU comment
posix-cpu-timers: Respect INFINITY for hard RTTIME limit
posix-cpu-timers: Switch thread group sampling to array
posix-cpu-timers: Restructure expiry array
posix-cpu-timers: Remove cputime_expires
...
- New board support: i.MX8MQ Nitrogen8m, Hummingboard Pulse,
PICO-PI-IMX8M, i.MX8QXP AI_ML, and LS1046A FRWY board.
- Add gpio-ranges for GPIO devices on i.MX8MQ and i.MX8MM.
- Update OPP table according to latest data sheet and add opp-suspend
to OPP table for i.MX8MQ and i.MX8MM.
- Add IDEL states for i.MX8MM SoC.
- Correct I2C clock divider for Layerscape SoCs.
- Add series alias and LPUART baud clock for i.MX8QXP SoC.
- Add MIPI D-PHY device for i.MX8MQ and enable it on imx8mq-librem5
board.
- Enable USB1 and Type-C support for i.MX8MM EVK board.
- Add Thermal Monitor Unit support for LS1028A SoC.
- Misc small update and correction on Layerscape and i.MX8 support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdYqNmAAoJEFBXWFqHsHzOXFoH/2x5pFXOcHkGcfjWAjguYu4C
gd+fgY/KIBR/t9Fk0Etvi6TRxB6qU061zOrjQSRIB8NCv7zy9P4LuJnyHQsJB8fw
XRYExzxtnsH2NAwpLQN1CX4AFqe9hGEGM3xspck6DQAA5S1fQUBSaak88WqEgfQp
kpf+PnoLMtrG6aUYHQbZXP1WSweH9w6zZwJUlN9YxTeJO91cHCbXdKPZ7NkLasxM
5hLeE8LCFaPGXeAPcgCXyweu2Lv9ncp5R+hx6tb4psfOd18RVz6mTWPYerAW7P/U
EBP/0hTm+7Lk4G4sZJ8a06Of1wBpDD1QprMa0fslzFRt7QzgbOYEvPINlVXRTAk=
=1mGW
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree update for 5.4:
- New board support: i.MX8MQ Nitrogen8m, Hummingboard Pulse,
PICO-PI-IMX8M, i.MX8QXP AI_ML, and LS1046A FRWY board.
- Add gpio-ranges for GPIO devices on i.MX8MQ and i.MX8MM.
- Update OPP table according to latest data sheet and add opp-suspend
to OPP table for i.MX8MQ and i.MX8MM.
- Add IDEL states for i.MX8MM SoC.
- Correct I2C clock divider for Layerscape SoCs.
- Add series alias and LPUART baud clock for i.MX8QXP SoC.
- Add MIPI D-PHY device for i.MX8MQ and enable it on imx8mq-librem5
board.
- Enable USB1 and Type-C support for i.MX8MM EVK board.
- Add Thermal Monitor Unit support for LS1028A SoC.
- Misc small update and correction on Layerscape and i.MX8 support.
* tag 'imx-dt64-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (41 commits)
arm64: dts: imx8mq: Add mux controller to iomuxc_gpr
arm64: dts: fsl: add support for Hummingboard Pulse
arm64: dts: ls1088a: update gpio compatible
arm64: dts: imx: Add i.mx8mq nitrogen8m basic dts support
arm64: dts: ls1088a-qds: Add the spi-flash nodes under the DSPI controller
arm64: dts: ls1088a: Add the DSPI controller node
arm64: dts: imx8mm: Enable cpu-idle driver
arm64: dts: ls1028a: Add esdhc node in dts
arm64: dts: ls1028a: Add properties node for Display output pixel clock
arm64: dts: lx2160a: Fix incorrect I2C clock divider
arm64: dts: ls1028a: Fix incorrect I2C clock divider
arm64: dts: ls1012a: Fix incorrect I2C clock divider
arm64: dts: ls1088a: Fix incorrect I2C clock divider
arm64: dts: ls1028a: fix gpio nodes
arm64: dts: ls1028a: Add Thermal Monitor Unit node
arm64: dts: imx8mq-evk: Unbypass audio_pll1
arm64: dts: imx8mm: Add opp-suspend property to OPP table
arm64: dts: imx8mq: Add opp-suspend property to OPP table
arm64: dts: ls1088a: Revise gpio registers to little-endian
arm64: dts: add the console node for DPAA2 platforms
...
Link: https://lore.kernel.org/r/20190825153237.28829-6-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add opp-suspend property to each OPP, the of opp core will
select the OPP HW supported and with highest rate to be
suspend opp, it will speed up the suspend/resume process.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The correct clock for "bus_early", "ref", "suspend" should be:
IMX8MQ_CLK_USB1_CTRL_ROOT, IMX8MQ_CLK_USB_CORE_REF, IMX8MQ_CLK_32K,
especially we may need the right suspend clock rate to set register
in controller driver.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MQ has clock gate for TMU module, add clock info to TMU
node for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to latest datasheet (Rev.1, 10/2018) from below links,
in the consumer datasheet, 1.5GHz is mentioned as highest opp but
depends on speed grading fuse, and in the industrial datasheet,
1.3GHz is mentioned as highest opp but depends on speed grading
fuse. 1.5GHz and 1.3GHz opp use same voltage, so no need for
consumer part to support 1.3GHz opp, with same voltage, CPU should
run at highest frequency in order to go into idle as quick as
possible, this can save power.
That means for consumer part, 1GHz/1.5GHz are supported, for
industrial part, 800MHz/1.3GHz are supported, and then check the
speed grading fuse to limit the highest CPU frequency further.
Correct the market segment bits in opp table to make them work
according to datasheets.
https://www.nxp.com/docs/en/data-sheet/IMX8MDQLQIEC.pdfhttps://www.nxp.com/docs/en/data-sheet/IMX8MDQLQCEC.pdf
Fixes: 12629c5c37 ("arm64: dts: imx8mq: Add cpu speed grading and all OPPs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The same ddr perfomance counter IP from 8qxp is also available on imx8m
series so add it to dts.
Tested with `perf stat` and `memtester` on imx8mm-evk and obtained
plausible results.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX8MQ pinctrl driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M SAI block is not compatible with the i.MX6SX one, as the
register layout has changed due to two version registers being added
at the beginning of the address map. Remove the bogus compatible.
Fixes: 8c61538dc9 ("arm64: dts: imx8mq: Add SAI2 node")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Add i.MX8MQ based Librem5 devkit support.
- Add SNVS power key support for i.MX8MQ and i.MX8MM.
- Add GPIO alias for imx8mq and i.MX8QXP.
- A series from Daniel Baluta to add SAI devices and enable audio
support for imx8mm-evk board.
- Add DDR performance monitor unit support for i.MX8QXP.
- Add irqsteer interrupt controller device for i.MX8MQ SoC.
- Add CPU speed grading and all OPPs for i.MX8MM and i.MX8MQ.
- Add OCOTP device node for i.MX8QXP.
- Various device addition for LS1028A: SATA, qDMA, USB, Mali DP500 and
temperature sensor.
- Random minor coding style improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdEcFcAAoJEFBXWFqHsHzOcNYIAICVsBiJX/gU0t+jT7i1KL83
jDe/DDNg8j9PgR0ElLPejskJgnNYLS0DTWYCY/yPgzK8bwLuqxseVyjXBhyptZ1o
Oecgp9c/79RGsJi9+tFlPKCB/jL4gvagbNn0kPAAoCv3dV5n5FikuSXfsN1v0DJi
JpBXO0IHpkqRTJKk7Ran5MzxxaHbWkjMn0u80ewsAioZv/XhPg5xVSsONleQdh2V
YtZkjcAuA7M9ZOLTKcEFmGyZW/ZTLcW7+xaj9ETJGtMJEi60igPyeFcmd1YIKfIh
g1RwqgDilwEbh2rNulyZbRkRJKQDjTeHUNRqyGEM54lxAB52VQo5hHYa56K2m9Q=
=SIR/
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree changes for 5.3:
- Add i.MX8MQ based Librem5 devkit support.
- Add SNVS power key support for i.MX8MQ and i.MX8MM.
- Add GPIO alias for imx8mq and i.MX8QXP.
- A series from Daniel Baluta to add SAI devices and enable audio
support for imx8mm-evk board.
- Add DDR performance monitor unit support for i.MX8QXP.
- Add irqsteer interrupt controller device for i.MX8MQ SoC.
- Add CPU speed grading and all OPPs for i.MX8MM and i.MX8MQ.
- Add OCOTP device node for i.MX8QXP.
- Various device addition for LS1028A: SATA, qDMA, USB, Mali DP500 and
temperature sensor.
- Random minor coding style improvements.
* tag 'imx-dt64-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (32 commits)
arm64: dts: librem5: enable the SNVS power key
arm64: dts: librem5: Limit the USB to 5V
arm64: dts: imx8qxp: added ddr performance monitor nodes
arm64: dts: imx8qxp: sort LSIO subsystem devices
arm64: dts: imx8qxp: sort alias alphabetically
arm64: dts: imx8qxp: Add lsio_mu13 node
arm64: dts: imx8mm-evk: Enable audio codec wm8524
arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit
arm64: dts: fsl: ls1028a: Add qDMA node
arm64: dts: imx8mm: Enable SNVS power key according to board design
arm64: dts: imx8mq-evk: Enable SNVS power key
arm64: dts: ls1028a: add crypto node
arm64: dts: ls1028a: Add temperature sensor node
arm64: dts: imx8mm: Move gic node into soc node
arm64: dts: imx8mm: Move usbphy out of soc node
arm64: dts: imx8mm: Pass the 'ranges' property
arm64: dts: imx8mm: Pass a unit name for the 'soc' node
arm64: dts: fsl: imx8mq: add the snvs power key node
arm64: dts: ls1028a: fix watchdog device node
arm64: dts: ls1028a: Enable sata.
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add a node for the snvs power key, "disabled" by default.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MQ has clock gate for SNVS module, add clock info to SNVS
RTC node for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Unnecessary blank lines do NOT help readability, so remove them.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add nvmem-cells reference to cpu and fill the OPP table with all known
OPPs.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a node for the irqsteer interrupt controller found on the iMX8MQ
SoC.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
v2 of "clk: imx: Refactor entire sccg pll clk" dropped the implicit
reparenting of the PLL output from the bypass clock to the real
PLL. The commit introducing the GPU node had only been tested against
v1 of this patch. Without an explicit reparent to the real PLL the
GPU is stuck at the bypass clock rate of 25MHz, serverly hampering
performance.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This enables the Vivante GC7000L GPU on the i.MX8MQ SoC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the datasheet both industrial and consumer variants support
at least 1.3GHz CPU frequency at 1.0V. Only the OPP at 1.5GHz is
unavailable on some SKUs and thus need further fuse reading support.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to NXP's FAE feedback and a comment in ATF firmware, PCIE1
and PCIE2 power domains can't really be used independently. Due to
shared reset line both power domains have to be turned on at the same
time. Account for that quirk by combining PCIE power domains into a
single 'pgc_pcie' power domain.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Mark iomuxc_gpr as compatible with "fsl,imx6q-iomuxc-gpr" in order for
to allow i.MX6 PCIe driver to use it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Set ahb clock on sdma1 to get rid of "Timeout waiting for CH0"
on the imx8mq.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix a typo in the compatible string
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
thermal-zones node does not have any register properties and thus
shouldn't be placed inside the bus.
Move thermal-zones node from soc node to root node in order to fix
the following build warning with W=1:
arch/arm64/boot/dts/freescale/imx8mq.dtsi:305.18-364.6: Warning (simple_bus_reg): /soc@0/bus@30000000/thermal-zones: missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move opp-table node from soc node to root node.
opp-table node does not have any register properties and thus
shouldn't be placed inside the bus.
This fixes the following build warnings with W=1:
arch/arm64/boot/dts/freescale/imx8mq.dtsi:687.28-703.5: Warning (simple_bus_reg): /soc@0/opp-table: missing or empty reg/ranges property
Fixes: 64d26f8c1d ("arm64: dts: imx8mq: Add the opp table and cores opp properties")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SAI2 is part of AIPS-3 memory region.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SDMA1 is part of AIPS-3 region and SDMA2 is part
of AIPS-1 region.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MQ has clock gate for each GPIO bank, add clock info
to GPIO node for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the 0.8GHz and 1GHz opps. According to the datasheet:
https://www.nxp.com/docs/en/data-sheet/IMX8MDQLQIEC.pdf
section 3.1.3 Operating ranges.
The 0.8GHz opp runs in nominal mode with the regulator set to 0.9V.
The 1GHz runs in overdrive mode with the regulator set to 1V.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
